600W with PFC and Parallel Function PSP-600 series Features : Universal AC input / Full range Built-in active PFC function Protections: Short circuit / Overload / Over voltage / Over temperature Forced air cooling by built-in DC fan With DC OK Signal output Current sharing up to 2400W(3+1) Built-in remote ON-OFF control Built-in remote sense function Fixed switching frequency at PFC:88KHz PWM:100KHz 3 years warranty SPECIFICATION MODEL PSP-600-5 PSP-600-12 PSP-600-13.5 PSP-600-15 PSP-600-24 PSP-600-27 PSP-600-48 DC VOLTAGE 5V 12V 13.5V 15V 24V 27V 48V RATED CURRENT 80A 50A 44.5A 40A 25A 22.2A 12.5A CURRENT RANGE 0 ~ 80A 0 ~ 50A 0 ~ 44.5A 0 ~ 40A 0 ~ 25A 0 ~ 22.2A 0 ~ 12.5A RATED POWER 400W 600W 600.75W 600W 600W 599.4W 600W RIPPLE & NOISE (max.) Note.2 180mVp-p 240mVp-p 240mVp-p 240mVp-p 240mVp-p 240mVp-p 300mVp-p OUTPUT VOLTAGE ADJ. RANGE 4.75 ~ 5.5V 10 ~ 13.2V 12 ~ 15V 13.5 ~ 18V 20 ~ 26.4V 24 ~ 30V 41 ~ 56V VOLTAGE TOLERANCE Note.3 2.0% 1.0% 1.0% 1.0% 1.0% 1.0% 1.0% LINE REGULATION 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% LOAD REGULATION 1.0% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% SETUP, RISE TIME 1500ms, 50ms at full load HOLD UP TIME (Typ.) 20ms at full load VOLTAGE RANGE Note.5 88 ~ 264VAC 124 ~ 370VDC FREQUENCY RANGE 47 ~ 63Hz POWER FACTOR (Typ.) 0.95/230VAC 0.99/115VAC at full load INPUT EFFICIENCY(Typ.) 79% 84% 85% 85% 86% 86% 87% AC CURRENT (Typ.) 6.8A/115VAC 3.4A/230VAC INRUSH CURRENT (Typ.) 20A/115VAC 40A/230VAC LEAKAGE CURRENT <1.3mA/240VAC 105 ~ 135% rated output power OVERLOAD Protection type : Constant current limiting, recovers automatically after fault condition is removed 5.75 ~ 6.75V 13.8 ~ 16.2V 15.5 ~ 18.2V 18 ~ 21V 27.6 ~ 32.4V 31 ~ 36.5V 57.6 ~ 67.2V OVER VOLTAGE Protection type : Shut down o/p voltage, re-power on to recover PROTECTION +5V: 95 (TSW1) detect on heatsink of power transistor; 95 (TSW51) detect on heatsink of power diode OVER TEMPERATURE +12V ~ +48V: 85 (TSW1) detect on heatsink of power transistor; 80 (TSW51) detect on heatsink of power diode Protection type : Shut down o/p voltage, re-power on to recover REMOTE CONTROL RC+/RC-: Short = power on ; Open = power off FUNCTION POK SIGNAL PSU turn on: 3.3V ~ 5.6V PSU turn off: 0V ~ 1V -20 ~ +60 (Refer to "Derating Curve") WORKING TEMP. 20 ~ 90% RH non-condensing WORKING HUMIDITY -40 ~ +85 , 10 ~ 95% RH ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT 0.03%/ (0 ~ 50 ) VIBRATION 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes SAFETY STANDARDS UL60950-1, TUV EN60950-1 approved WITHSTAND VOLTAGE I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC SAFETY & ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH EMC (Note 4) EMC EMISSION Compliance to EN55022 (CISPR22) Class B, EN61000-3-2,-3 EMC IMMUNITY Compliance to EN61000-4-2,3,4,5,6,8,11, light industry level, criteria A MTBF 116.4K hrs min. MIL-HDBK-217F (25 ) OTHERS DIMENSION 170*120*93mm (L*W*H) PACKING 1.9Kg; 8pcs/15.5Kg/1.06CUFT 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. NOTE 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. For guidance on how to perform these EMC tests, please refer to “EMI testing of component power supplies.” (as available on http://www.meanwell.com) 5. Derating may be needed under low input voltages. Please check the derating curve for more details. File Name:PSP-600-SPEC 2011-11-30 Air flow direction 600W with PFC and Parallel Function PSP-600 series Mechanical Specification Case No.910A Unit:mm RS Connector(CN5) : JST B-XH or equivalent Pin No. Assignment Mating Housing Terminal 1 RS+ JST XHP JST SXH-001T or equivalent or equivalent 2 RS- Terminal Pin No. Assignment 2-M3 L=4mm max. Pin No. Assignment 2-M3 L=4mm max. 1 AC/L 2 AC/N 3 FG 4 P(Current Share) 5 POK 6 R.C. G 150 7 R.C. 8~11 DC OUTPUT +V 185 12~15 DC OUTPUT -V 120 170 150 8 11.5 1 2 3 4 5 6 7 2-M3 L=4mm max. 2-M3 L=4mm max. 14 max. 1 2 CN5 8 9 10 11 12 13 14 15 9.5 11.5 Block Diagram PFC fosc : 88KHz PWM fosc : 100KHz FAN SIGNAL POK CONTROL CURRENT SHARING P CIRCUIT ACTIVE RECTIFIERS RECTIFIERS POWER +V EMI INRUSH I/P & & CURRENT FILTER SWITCHING -V P.F.C. FILTER LIMITING RC.G. O.C.P. RC FG DETECTION CIRCUIT PWM O.L.P. CONTROL O.V.P. O.T.P. Derating Curve Output Derating VS Input Voltage 100 100 Others 90 80 80 70 60 12V 50 60 40 50 20 40 -20 0 10 20 30 40 45 50 60 (HORIZONTAL) 88 100 115 135 155 230 264 AMBIENT TEMPERATURE ( ) INPUT VOLTAGE (V) 60Hz File Name:PSP-600-SPEC 2011-11-30 LOAD (%) LOAD(%) 50 58.3 93 100 600W with PFC and Parallel Function PSP-600 series Control Terminal Instruction Manual POK(+) RCG(-) RCG RC L N FG P POK RCG RC L N FG P POK RCG RC L N FG P POK RCG RC +V +V +V +V -V -V -V -V +V +V +V +V -V -V -V -V +V +V +V +V -V -V -V -V RS+ RS- RS+ RS- RS+ RS- + - + - + - LOAD LOAD LOAD Remote Sensing POK Signal Remote Control Power ON: RCG and RC for short POK Signal is the voltage difference between Power OFF: RCG and RC for open "RCG" and "POK" pin output POK Signal for TTL level signal PSU turn on: 3.3V ~ 5.6V PSU turn off: 0V ~ 1V Parallel Operation with Remote Sensing (1)Parallel operation is available by connecting the units shown as below (+S,-S and P are connected mutually in parallel) : (2)The voltage difference among each output should be minimized that less than 2% is required. (3)The total output current must not exceed the value determined by the following equation (Output current at parallel operation) =(The rated current per unit) x (Number of unit) x 0.9. (4) In parallel operation 4 units is the maximum, please consult the manufacture for other applications. (5) When remote sensing is used in parallel operation, the sensing wire must be connected only to the master unit. (6) When in parallel operation, the minimum output load should be greater than 3% of total output load. (Min. load > 3% rated current per unit x number of unit) LOAD +V -V +S -S + - P RCG RS+ RS- + - P RCG RS+ RS- + - P RCG RS+ RS- + - P RCG RS+ RS- PSU PSU PSU PSU File Name:PSP-600-SPEC 2011-11-30