150W Single Output Switching Power Supply CLG - 15 0 s e ri e s Features : Universal AC input / Full range (up to 295VAC) Built-in active PFC function High efficiency up to 91% Protections: Short circuit / Over current / Over voltage / Over temperature Cooling by free air convection OCP point adjustable through output cable or internal potentiometer IP65 / IP67 design for indoor or outdoor installations Suitable for LED lighting and moving sign applications Compliance to worldwide safety regulations for lighting 3 years warranty 110 F SELV I P 6 5 I P 6 7 (option) CLG-150-12 A Blank : IP67 rated. Cable for I/O connection. A : IP65 rated. Output voltage and constant current level can be adjusted through internal potentiometer. B : IP67 rated. Constant current level adjustable through output cable. C : Terminal block for I/O connection. Output voltage and constant current level can be adjusted through internal potentiometer. SPECIFICATION MODEL CLG-150-12 CLG-150-15 CLG-150-20 CLG-150-24 CLG-150-30 CLG-150-36 CLG-150-48 DC VOLTAGE 12V 15V 20V 24V 30V 36V 48V CONSTANT CURRENT REGION Note.4 9 ~12V 11.25 ~ 15V 15 ~ 20V 18 ~ 24V 22.5 ~ 30V 27 ~ 36V 36 ~ 48V RATED CURRENT 11A 9.5A 7.5A 6.3A 5A 4.2A 3.2A RATED POWER 132W 142.5W 150W 151.2W 150W 151.2W 153.6W RIPPLE & NOISE (max.) Note.2 150mVp-p 150mVp-p 150mVp-p 150mVp-p 150mVp-p 150mVp-p 200mVp-p VOLTAGE ADJ. RANGE Note.6 9 ~ 13V 13 ~ 17V 17 ~ 22V 22 ~ 27V 26 ~ 32V 31 ~ 41V 40 ~ 56V OUTPUT Can be adjusted by internal potentiometer or through output cable CURRENT ADJ. RANGE 5.5 ~ 11A 4.75 ~ 9.5A 3.75 ~ 7.5A 3.15 ~ 6.3A 2.5 ~ 5A 2.1 ~ 4.2A 1.6 ~ 3.2A VOLTAGE TOLERANCE Note.3 2.0% 2.0% 2.0% 1.0% 1.0% 1.0% 1.0% LINE REGULATION 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% LOAD REGULATION 1.0% 1.0% 1.0% 0.5% 0.5% 0.5% 0.5% SETUP, RISE TIME 3000ms, 80ms at full load 230VAC /115VAC HOLD UP TIME (Typ.) 50ms / 230VAC 16ms / 115VAC at full load VOLTAGE RANGE Note.5 90 ~ 295VAC 127 ~ 417VDC FREQUENCY RANGE 47 ~ 63Hz POWER FACTOR (Typ.) PF>0.98/115VAC, PF>0.95/230VAC, PF>0.93/277VAC at full load (Please refer to "Power Factor Characteristic" curve) INPUT EFFICIENCY (Typ.) 88% 88% 90% 90% 91% 91% 91% AC CURRENT (Typ.) 2A / 115VAC 1A / 230VAC 0.68A / 277VAC INRUSH CURRENT(max.) COLD START 65A/230VAC LEAKAGE CURRENT <1mA / 240VAC 95 ~ 108% OVER CURRENT (Typ.) Note.4 Protection type : Constant current limiting, recovers automatically after fault condition is removed SHORT CIRCUIT Hiccup mode, recovers automatically after fault condition is removed PROTECTION 13.5 ~ 16V 18 ~ 20V 23 ~ 27V 28 ~ 34V 33 ~ 36V 42 ~ 48V 59 ~ 70V OVER VOLTAGE Protection type : Shut down and latch off o/p voltage, re-power on to recover 100 10 (RTH2) OVER TEMPERATURE Protection type : Shut down o/p voltage, re-power on to recover -30 ~ +70 (Refer to "Derating Curve") WORKING TEMP. 20 ~ 95% RH non-condensing WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY -40 ~ +80 , 10 ~ 95% RH TEMP. COEFFICIENT 0.03%/ (0 ~ 50 ) VIBRATION 10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes UL8750, CSA C22.2 No. 250.0-08, UL1012, CAN/CSA-C22.2 No. 107.1-01, EN61347-1, EN61347-2-13 independent SAFETY STANDARDS Note.7 (except for CLG-150 C type), UL60950-1, TUV EN60950-1,IP65 or IP67, J61347-1(option, except for CLG-150 C type), J61347-2-13 approved SAFETY & WITHSTAND VOLTAGE I/P-O/P:3.75KVAC I/P-FG:1.88KVAC O/P-FG:0.5KVAC EMC ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH EMC EMISSION Compliance to EN55015, EN55022 (CISPR22) Class B, EN61000-3-2 Class C ( 75% load) ; EN61000-3-3 EMC IMMUNITY Compliance to EN61000-4-2,3,4,5,6,8,11, EN61547, EN55024, light industry level (surge 4KV), criteria A MTBF 303.7Khrs min. MIL-HDBK-217F (25 ) OTHERS DIMENSION 222.2*68*38.8mm (L*W*H)(CLG-150-Blank/A/B) 229*68*38.8mm (L*W*H)(CLG-150-C) 1.0Kg; 12pcs/13Kg/0.58CUFT(CLG-150-Blank/A/B) 1Kg; 12pcs/13Kg/0.96CUFT(CLG-150-C) PACKING 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. NOTE 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. Constant current operation region is within 75% ~100% rated output voltage. This is the suitable operation region for LED related applications, but please reconfirm special electrical requirements for some specific system design. 5. Derating may be needed under low input voltages. Please check the static characteristics for more details. 6. Type A and type C only. 7. Safety and EMC design refer to EN60598-1, subject 8750(UL), CNS15233, GB7000.1, FCC part18. 8. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again. File Name:CLG-150-SPEC 2012-03-12 150W Single Output Switching Power Supply CLG -150 series Mechanical Specification Case No. 954A Unit:mm Blank:(CLG-150) 222.2 12 198.2 9.6 300 20 300 20 T case AC/L(Brown) 99.1 +V(Red) AC/N(Blue) -V(Black) FG (Green/Yellow) SJTW 14AWG 2C SJTW 18AWG 3C 4.2 4PL T case: Max. Case Temperature. IP67 rated. Cable for I/O connection. A Type:(CLG-150-_A) 222.2 198.2 12 9.6 Io ADJ. 300 20 300 20 T case AC/L(Brown) 99.1 +V(Red) AC/N(Blue) -V(Black) FG (Green/Yellow) SJTW 14AWG 2C SJTW 18AWG 3C Vo ADJ. 4.2 4PL T case: Max. Case Temperature. IP65 rated. Output voltage and constant current level can be adjusted through internal potentiometer. (Can access by removing the rubber stopper on the case.) File Name:CLG-150-SPEC 2012-03-12 9.4 34.2 9.4 9.4 34.2 9.4 68 68 34 34 38.8 38.8 150W Single Output Switching Power Supply CLG -150 series B Type:(CLG-150-_B) 222.2 12 198.2 9.6 300 20 300 20 SJTW 14AWG 2C +V(Red) AC/L(Brown) T case -V(Black) 99.1 SJTW 18AWG 2C AC/N(Blue) ADJ1(Blue) FG (Green/Yellow) SJTW 18AWG 3C ADJ2(White) 4.2 4PL T case: Max. Case Temperature. IP67 rated. Output constant current level can be adjusted through output cable by connecting a resistor between ADJ1 and ADJ2. Reference resistance value for output current adjustment (Typical) Resistance Percentage of rated current Open Slightly > 100% 4.7K 100% 620 75% 82 50% Short Slightly < 50% C Type:(CLG-150-_C) 229 15.4 198.2 8 AC Input Terminal Pin No. Io ADJ. Assignment 1 T case 1 99.1 I/P 2 O/P Pin No. Assignment 2 1 FG 3 Vo ADJ. 2 AC/N 3 AC/L 4.2 4PL T case: Max. Case Temperature. DC Output Terminal Pin No. Assignment Pin No. Assignment 1 +V 2 -V Output voltage and constant current level can be adjusted through internal potentiometer. (Can access by removing the rubber stopper on the case.) File Name:CLG-150-SPEC 2012-03-12 7.5 9.5 8 37 8 68 9.4 34.2 9.4 68 34 34 38.8 38.8 150W Single Output Switching Power Supply CLG -150 series Block Diagram Fosc : 100KHz RECTIFIERS EMI FILTER POWER PFC +V I/P & & SWITCHING CIRCUIT -V RECTIFIERS FILTER ADJ1 O.L.P. ADJ2 (B Type) DETECTION FG O.L.P. CIRCUIT PWM & PFC PFC CONTROL CONTROL O.V.P. Derating Curve Static Characteristics 100 100 230VAC 90 80 230VAC 80 Input only 70 100VAC 60 60 40 50 20 40 (HORIZONTAL) -30 -25 -10 0 15 30 50 55 60 70 90 100 125 135 145 155 165 175 180 200 230 295 AMBIENT TEMPERATURE ( ) INPUT VOLTAGE (V) 60Hz File Name:CLG-150-SPEC 2012-03-12 LOAD (%) LOAD (%) 150W Single Output Switching Power Supply CLG -150 series Power Factor Characteristic Constant Current Mode 1 . 0 0 0 . 9 8 0 . 9 6 0 . 9 4 0 . 9 2 2 7 7 V a c 0 . 9 0 0 . 8 8 2 3 0 V a c 0 . 8 6 1 1 5 V a c 0 . 8 4 0 . 8 2 0 . 8 0 0 . 7 8 5 0 % 6 0 % 7 0 % 8 0 % 9 0 % 1 0 0 % (150W) LOAD EFFICIENCY vs LOAD (48V Model) CLG-150 series possess superior working efficiency that up to 91% can be reached in field applications. 9 6 9 2 8 8 8 4 2 7 7 V ac 8 0 2 3 0 V ac 7 6 1 1 5 V ac 7 2 6 8 6 4 1 0 % 2 0 % 3 0 % 4 0 % 5 0 % 6 0 % 7 0 % 8 0 % 9 0 % 1 0 0 % LOAD DRIVING METHODS OF LED MODULE There are two major kinds of LED drive method "direct drive" and "with LED driver". A typical LED power supply may either work in "constant voltage mode (CV) or constant current mode (CC)" to drive the LEDs. Mean Well's LED power supply with CV+ CC characteristic can be operated at both CV mode [with LED driver, at area (A)] and CC mode [direct drive, at area (B)]. 100 (B) Constant Current area (A) Constant Voltage area 75 (max.) (C) Hiccup Protection 75 100 Io (%) Typical LED power supply I-V curve File Name:CLG-150-SPEC 2012-03-12 PF EFFICIENCY (%) Vo(%)