150W MICRO ATX PC Power Supply ATX-68A s e ri e s Features : AC input range selected by switch With +5VSB:0 ~ 0.75A max. Power good signal output Power fail signal output High efficiency Approvals: CSA/ TUV/ CB/ CE/ FCC Forced air cooling by built-in DC fan 100% full load burn-in test Low cost 1 year warranty SPECIFICATION MODEL CH1 CH2 CH3 CH4 STANDBY DC VOLTAGE 3.3V 5V 12V -12V 5VSB MINIMUM CURRENT 1.2A 1.0A 0.1A 0.1A 0A MAXIMUM CURRENT 6.0A 12A 5.0A 0.3A 0.75A RATED POWER (max.) 150W continue OUTPUT RIPPLE & NOISE (max.) Note.2 50mVp-p 50mVp-p 120mVp-p 120mVp-p 50mVp-p LINE REGULATION 1% 1% 1% 2% 1% LOAD REGULATION Note.3 5% 5% 5% 10% 5% HOLD UP TIME 16ms min. at full load AC VOLTAGE 115 / 230VAC 1 / 0.5A VOLTAGE RANGE 100 ~ 132VAC/ 200 ~ 264VAC selected by switch FREQUENCY RANGE 47~63Hz EFFICIENCY (Typ.) 70% INPUT AC CURRENT 4.0A / 115VAC 2.0A / 230VAC INRUSH CURRENT (max.) 40A / 115VAC 80A / 230VAC LEAKAGE CURRENT(max.) 3.5mA / 240VAC 105~150% rated output power OVER LOAD Protection type : Shut down o/p voltage, re-power on to recover PROTECTION All output equipped with short circuit SHORT CIRCUIT Protection type : Shut down o/p voltage, re-power on to recover POWER GOOD SIGNAL The TTL compatible signal out with 100ms to 500ms delay after power set up POWER FAIL SIGNAL The TTL compatible signal will go down at least 1ms before +5V below 4.7V FUNCTION PS-ON INPUT SIGNAL Power on: PS-ON = "Low" or "<0.8V" ; Power off: PS-ON = "Hi" or ">2V" WORKING TEMP. -10~+40 WORKING HUMIDITY 20~90% RH non-condensing STORAGE TEMP., HUMIDITY -20~+85 , 10~95% RH ENVIRONMENT TEMP. COEFFICIENT 0.05% / (0~50 ) VIBRATION 10~200Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes CSA22.2, UL1950, TUV EN60950 Approved SAFETY STANDARDS WITHSTAND VOLTAGE I/P-O/P, I/P-FG:1.5KVAC SAFETY & ISOLATION RESISTANCE I/P-O/P, I/P-FG:50M Ohms / 500VDC Compliance to EN55022 (CISPR22) Class B, FCC part 15 class B EMC EMI CONDUCTION & RADIATION (Note 4) HARMONIC CURRENT Compliance to EN61000-3-2,-3 Compliance to EN61000-4-2,3,4, Light industry level, criteria A EMS IMMUNITY MTBF 100K hrs min. MIL-HDBK-217F (25 ) ATX main power connector * 1ea ; Peripheral power connector * 3 ea ; Floppy drive power connector * 1ea CONNECTOR OTHERS COOLING Forced air ventilation by 8cm DC fan DIMENSION 125*100*64mm (L*W*H) PACKING 0.7kg; 20pcs / 19kg / CARTON NOTE 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Load regulation is measured from 20% to 100% max. Load. 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. File Name: ATX- 68A-SPEC 2004-06-21 150W MICRO ATX PC Power Supply ATX-68A Mechanical Specification Unit:mm 63.5 51.5 3 49 31.8 33.25 125 (A)ATX main power connector Type: MOLEX 39-01-2200 or equivalent (B)Peripheral connector Type: MOLEX 8981-04P or equivalent (C)FLOPPY drive connector Type: AMP 171822-4 or equivalent ( B ) ( B ) ( B ) ( C ) ( A ) File Name: ATX -68A-SPEC 2004-06-21 INPUT 100 VOLTAGE 88 RANGE SWITCH WIRE OUTPUT OF CASE +5VDC +12VDC +5VDC 5VSB -5VDC PW-OK GND GND GND +5VDC GND GND PS-ON +5VDC GND GND AC -12VDC +3.3VDC T T OU PU +3.3VDC +3.3VDC 28.25 44.6 21.4 CONNECTOR AC PIN11 PIN1 INPUT L=300mm 20mm CONNECTOR 4 +5VDC 3 COM COM 2 +12VDC 1 L=150mm L=300mm 20mm +5VDC 4 COM 3 COM 2 +12VDC 1 L=150mm +5VDC 4 COM 3 COM 2 +12VDC 1 L=150mm +5VDC 1 COM 2 COM 3 4 +12VDC L=150mm 49.5 14.25