MODEL: M6NXV (Configurator software is used to change output over the Screw Terminal Ultra-Slim Signal Conditioners M6N Series described range of the selected suffix code. For changing between suffix codes, set the Output Range SIGNAL TRANSMITTER Selector on the side of unit before software adjustment.) (PC programmable) Functions & Features POWER INPUT • 7.5-mm wide ultra-slim design DC Power • Low profile allows the M6N module mounted in a 120-mm R: 24 V DC deep panel (Operational voltage range 24 V ±10 %, ripple 10 %p-p max.) • Converts a DC input into a standard process signal • PC programmable • High-density mounting [3] OPTIONS • Power indicator LED STANDARDS & APPROVALS • UL approval blank: CE marking /UL: UL approval (CE marking) 7.5 (.30) RELATED PRODUCTS • PC configurator software (model: M6CFG) 102 Downloadable at M-System’s web site. (4.02) A dedicated cable is required to connect the module to the PC. Please refer to the internet software download site or the users manual for the PC configurator for applicable cable types. 102 (4.02) mm (inch) GENERAL SPECIFICATIONS Connection Input and output: M3 screw terminal (torque 0.5 N·m) MODEL: M6NXV–[1][2]–R[3] Power input: Via the Installation Base (model: M6NBS) or M3 screw terminal (torque 0.5 N·m) ORDERING INFORMATION Recommended solderless terminal: Max. 5.8 mm (0.23”) • Code number: M6NXV-[1][2]-R[3] wide; Ones with insulation sleeve do not fit. Specify a code from below for each [1] through [3]. Applicable wire size 0.2 – 2.5 mm2 (e.g. M6NXV-Z1Z1-R/UL) Housing material: Flame-resistant resin (black) • Input range (e.g. 4 – 20 mA DC) Isolation: Input to output to power • Output range (e.g. 4 – 20 mA DC) Overrange output: -2 – +102 % (Negative current output is not available.) Zero adjustment: -2 to +2% (PC programming) [1] INPUT Span adjustment: 98 to 102% (PC programming) Current Power LED: Green light turns on when the power is supplied. Z1: Range 0 – 50 mA DC (Input resistance 24.9 Ω) Status indicator LED: Orange LED; Flashing patterns Voltage indicate different operating status of the transmitter. S1: Range -1000 – +1000 mV DC (Input resistance 1 MΩ min.) Programming: Downloaded from PC; input type and range, S2: Range -10 – +10 V DC (Input resistance 1 MΩ min.) output type and range, zero and span, user’s linearization (Configurator software is used to change the input type and table (max. 101 points, specified within -2 to +102% for precise range.) both input and output), etc. For detailed information, refer to the users manual for the [2] OUTPUT PC configurator. Current Configurator connection: 2.5 dia. miniature jack; Z1: Range 0 – 20 mA DC RS-232C level Voltage V2: Range -10 – +10 V DC V3: Range -5 – +5 V DC http://www.m-system.co.jp/ M6NXV SPECIFICATIONS ES-7912 Rev.5 Page 1/4 MODEL: M6NXV ■Recommended solderless terminal (e.g. 1 – 5 V: 5000 Ω [5 V/1 mA]) 5.5 max. 4 min. If not specified, the output range is shown below. (.22) (.16) 3.2 (.13) dia. V2: 0 – 10 V DC V3: 1 – 5 V DC INSTALLATION Power consumption: Approx. 0.5 W Operating temperature: -20 to +55°C (-4 to +131°F) INPUT SPECIFICATIONS Operating humidity: 30 to 90 %RH (non-condensing) • DC Current: Input resistor incoporated Mounting: Installation Base (model: M6NBS) or DIN rail (If not specified, the input range is 4 – 20 mA DC.) Weight: 65 g (2.3 oz) Input range: 0 – 50 mA DC Minimum span: 2 mA Offset: Lower range can be any specific value within the PERFORMANCE in percentage of span input range provided that the minimum span is maintained. Overall accuracy: Input accuracy + output accuracy • DC Voltage Inversely proportional to the span. Code S1 (narrow spans) See CALCULATION EXAMPLES OF OVERALL ACURACY. Input range: -1000 – +1000 mV DC • Input accuracy: (% of max. input range) Minimum span: 100 mV -1000 – +1000 mV : ±0.01 % Code S2 (wide spans) -10 – +10 V : ±0.01 % Input range: -10 – +10 V DC 0 – 50 mA : ±0.02 % Minimum span: 1 V • Output accuracy: ±0.04 % of max. output range Offset: Lower range can be any specific value within the Temp. coefficient: ±0.01 %/°C (±0.006 %/°F) of max. span input range provided that the minimum span is maintained. Response time: ≤ 0.5 sec. (0 – 90 %) If not specified, the input range is shown below. Line voltage effect: ±0.1 % over voltage range S1: 0 – 100 mV DC Insulation resistance: ≥ 100 MΩ with 500 V DC S2: 1 – 5 V DC Dielectric strength: 2000 V AC @1 minute (input to output to power to ground) OUTPUT SPECIFICATIONS • DC CURRENT CALCULATION EXAMPLES OF OVERALL ACCURACY Output range: 0 – 20 mA DC [Example] Input Type -10 – +10 V, Input Range 1 – 5 V, Conformance range: 0 – 20.4 mA DC Output Type -5 – +5 V, Output Range 1 – 5 V Minimum span: 1 mA • Input accuracy = Max. Input Range (20 V) / Span (4 V) × Offset: Lower range can be any specific value within the 0.01 % = 0.05 % output range provided that the minimum span is • Output accuracy = Max. Output Range (10 V) / Span (4 V) maintained. × 0.04 % = 0.1 % Load resistance: Output drive 11 V max. Accuracy= ±0.15 % (e.g. 4 – 20 mA: 550 Ω [11 V/20 mA]) If not specified, the output range is 4 – 20 mA DC. STANDARDS & APPROVALS • DC VOLTAGE CE conformity: Code V2 (wide spans) EMC Directive (2004/108/EC) Output range: -10 – +10 V DC EN 61000-6-4 (EMI) Conformance range: -10.4 – +10.4 V DC EN 61000-6-2 (EMS) Minimum span: 1 V Approval: Code V3 (narrow spans) UL/C-UL nonincendive Class I, Division 2, Output range: -5 – +5 V DC Groups A, B, C, and D hazardous locations Conformance range: -5.2 – +5.2 V DC (ANSI/ISA-12.12.01, CAN/CSA-C22.2 No.213) Minimum span: 0.5 V UL/C-UL general safety requirements Offset: Lower range can be any specific value within the (UL 61010-1, CAN/CSA-C22.2 No.61010-1) output range provided that the minimum span is maintained. Load resistance: Output drive 1 mA max. http://www.m-system.co.jp/ M6NXV SPECIFICATIONS ES-7912 Rev.5 Page 2/4 5.8 max. (.23) MODEL: M6NXV EXTERNAL VIEW � FRONT VIEW (with the cover open) � SIDE VIEW 5 6 7 8 Power LED Status Indicator LED Output Range Selectors Configurator Jack 1 2 3 4 The DIP switch setting is required to select output types before setting a precise output range using PC Configurator Software (model: M6CFG). Refer to the instruction manual for detailed procedures. DIMENSIONS unit: mm (inch) SCREWDRIVER * WIRE INSERTION ANGLE INSERTION ANGLE : approx. 35° : approx. 55° 8–M3 SCREW TERMINAL DIN RAIL HOOK 5 6 7 8 DIN RAIL 35mm wide 1 2 3 4 [1 (.04)] SCREWDRIVER INSERTION ANGLE : approx. 40° 7.5 (.30) 102 (4.02) *Screwdriver stem diameter: 6 mm (.24”) or less • When mounting, no extra space is needed between units. http://www.m-system.co.jp/ M6NXV SPECIFICATIONS ES-7912 Rev.5 Page 3/4 102 (4.02) SW1 SW1 ON OFF 1 2 3 4 5 6 7 8 MODEL: M6NXV SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM STATUS LED DIP SW Isolation 24.9Ω + Digital Output 1 5 + Computation Driver CURRENT OUTPUT (Z1) Low Drift – 2 6 – – Amplifier VOLTAGE POWER LED (S1, S2) 3 + + 7 POWER 4 – 8 CONFIGURATOR JACK POWER Specifications are subject to change without notice. http://www.m-system.co.jp/ M6NXV SPECIFICATIONS ES-7912 Rev.5 Page 4/4 CONNECTOR