Installation and Operation Manual P S 5 2 P o w e r S u p p l y B a r C o d e S y s t e m s © 1999 SICK, Inc. 6900 West 110th Street Bloomington, Minnesota 55438 USA Tel: 952 •941 •6780 Fax: 952 •941 •9287 w w w. s i c k o p t i c . c o m I n t r o d u c t i on The PS 52 Power Supply, with an input voltage of 115/230 V AC or 24 V DC (model dependent), is designed to provide a 24 V DC source for a single CLV 21X, 220 or 41X bar code scanner. Standard 9-pin D-Sub and 15-pin out box, since its terminal block can be easily accessed via PG connector ports located on the side of the enclo- sure. The terminal block incorporates the communication interface and discrete inputs/outputs of the scanners. This terminal block provides easy access in applications where hardwiring, due to long cable runs, is preferable to a D-Sub connector type interface. w w w . s i c k o p t i c . c o m 8 0 0 • 3 2 5 • 7 4 2 5 1 D-Sub female connectors make for easy connectivity on the PS 52. The PS 52 also acts as a distribution or break- PS 52 Port Functionality Figure 1 PORT FUNCTIONALITY TerminalConnection to Host Device to program the CLV series scanners using the CLV Setup Software. The communication parameters are an RS 232 iwith a 2400-baud rate, 8 data bits, 1 stop bit, and no parity.Astraight through cable can be used to connect this port to the RS 232 serial port of the PC. This port is a 9-pin D-Sub female connector. *Note: Only used for the CLV 21x and 220 scanners HostConnection to Host Device is for transmission of the bar code data to the Host Device. The This port is a 9-pin D-Sub female connector. *Note: Also used to program CLV 410, 412 and 414 bar code scanners using the CLV Setup Software CLVConnection of the CLV 21x, 220 and 41x to supply power, communications, and discrete input/output. This port is a 15-pin D-Sub high density female connector. 8 0 0 • 3 2 5 • 7 4 2 5 w w w . s i c k o p t i c . c o m 2 interface is dependent upon the type of bar code scanner attached. f a c en t e r D-Sub Connector Pin-out Functionality 1 2 1 PIN TERMINAL PORT HOST PORT CLV PORT CLV PORT 1N/CN/C+24 V+24 V 2AUX TxD RS232 TxD RS232Sensor 2AUX RxDRS232 3AUX RxD RS232RxD RS232 Output 3AUX TxDRS232 4N/C Term 422Term 422Term 422 5GNDGNDGNDGND 6N/C T+RS422R+RS422R+ RS422 7N/CT-RS422R-RS422R- 8N/C R+RS422T+RS422T+ RS422 9N/CR-RS422T-RS422T- 10RxDRS232RxDRS232 11TxDRS232TxDRS232 12Output 1Device Ready 13Output 2Read Result 14Sensor 1Sensor 15Sensor GNDSensor GND 1 Configuration for use with CLV 21x, 220 2 Configuration for use with 41x Figure 2 w w w . s i c k o p t i c . c o m 8 0 0 • 3 2 5 • 7 4 2 5 3 R S 4 2 2 R S 4 2 2 16 Pole Terminal Block The 16 pole terminal block is used to make hardwire connection to various bar code scanner signals. In most applications, this is not required. Below is the list of signals and functionality of each. 123456789101112141516 OUTOUTOUT422SEN T-R+R-T+GNDRXDTXDGNDGND+24 123TRM12 Figure 3 PIN # SIGNAL FUNCTION 1R+RS 422 Receive + line from CLV host port (Also RS 485 Receive line) 2R-RS 422 Receive - line from CLV host port 3T+ RS 422 Transmit + line from CLV host port (Also RS 485 Transmit line) 4T-RS 422 Transmit - line from CLV host port 5OUT1Discrete output line #1 24 V DC PNP(Device Ready) 6OUT2Discrete output line #2 24 V DC PNP(Read Result) 7OUT3Discrete output line #3 24 V DC PNP 8GNDSignal Ground 9RXDRS 232 Receive line from CLV Host port 10TXDRS 232 Transmit line from CLV Host port 11GNDSignal Ground 12422 TERMTermination line for the RS 422 interface 13SEN 1Sensor input line (1) to trigger the scanner 14GNDSignal Ground 15+ 2424 V DC line 16SEN 2Sensor input line (2) to trigger the scanner Figure 4 8 0 0 • 3 2 5 • 7 4 2 5 w w w . s i c k o p t i c . c o m 4 S E N 1 3 Functionality of Molex Interface (J3) 1+24 V DC RxD (RS 232) The 24 V DC version TxD (RS 232) This connector is an of the PS 52 extension of the GND(PS 52-0000) has a terminal block. It's intended2-position terminal of DC OUTPUT1 input. The input is polarityuse is to provide extra connectivity without independent for ease of OUTPUT2 consuming the terminalwiring. block connections.OUTPUT3 SENSOR 2 SENSOR 19 + - 9 1 w w w . s i c k o p t i c . c o m 8 0 0 • 3 2 5 • 7 4 2 5 5 CLV 410, 412, 414 Standard Configuration 1 To PC running CLV Setup Software for programming CLV or To Host Device for data transmission (PC, computer, etc.) 1 7 021 8512 m Interface Cable 7 021 8493 m Interface Cable 8 0 0 • 3 2 5 • 7 4 2 5 w w w . s i c k o p t i c . c o m 6 CLV 21X, 220 Standard Configuration To PC running CLV Setup Software for programming CLV 1 CLV 21X, 220 1 To Host Device for data transmission (PC, computer, etc.) 1 7 021 8512 m Interface Cable 7 021 8493 m Interface Cable w w w . s i c k o p t i c . c o m 8 0 0 • 3 2 5 • 7 4 2 5 7 Dimensional Drawings Dimensions in mm (in) Figure 6 8 0 0 • 3 2 5 • 7 4 2 5 w w w . s i c k o p t i c . c o m 8 Technical Specifications PS 52 POWER SUPPLY Input Voltage115 V AC / 230 V AC 60/50 Hz Output Voltage24 V DC ±20% Max. Power Output350 mA Enclosure MaterialPolycarbonate Enclosure RatingNEMA12 (pending), FCC Class APart 15 compliance, CE compliant Transformer RatingUL, CSA Dimensions (Lx W x H)115 x 90 x 80 mm (4.53 x 3.54 x 3.15 in) Weight0.64 kg (1.40 lb) Operating Temperature0…70° C (32…158° F) Relative Humidity90% non-condensing MountingOne side, 4 holes, 4.76 mm (.19 in) diameter Power Cord Length1.83 m (6 ft) Figure 7 w w w . s i c k o p t i c . c o m 8 0 0 • 3 2 5 • 7 4 2 5 9 . S a l e s • S e r v i c e • S u p p o r t For more information and application assistance, please call: 8 0 0 - 3 2 5 - 7 4 2 5 Visit us on the World Wide W w w w. s i c k o p t i c . c o m i n f o @ s i c k o p t i c . c o m SICK, INC. • 6900 WEST110TH STREET• BLOOMINGTON MN 55438 USA PHONE (952) 941-6780 • FAX (952) 941-9287 7 022 644.0006 E m a i l : e b : o r l dNorth America and the W Industrial Automation Products for