860 10025 860 10118 Remote Control Unit Kathrein’s 860 10025 and 860 10118 Remote Control Units (RCU) allow operators to control the electrical tilt of compatible antennas without direct access to the antenna. • Automatically calibrate to the antenna. There is no need to preset the antenna’s electrical tilt or the RCU when installing the unit. • Allow control of the antenna either locally through a laptop computer, on site desktop computer, the optional central control unit; remotely via an ethernet network or over the internet. • May be retrofitted to compatible antennas without dismantling or removing the antenna. • Suitable for daisy chain and splitter solutions. • Suitable for outdoor use. Specifications: Protocols AISG 1.1 and 3GPP/AISG 2.0 compliant 1) Logical interface ex factory AISG 1.1 860 10025 3GPP/AISG 2.0 860 10118 Input voltage range 10–30 V (pin 1 and pin 6) Power Consumption <1 W (standby); <8.5 W (motor activated) 2) Connectors 2 x 8 pin connector according to IEC 60130-9 conforming with AISG Daisy chain in: male; Daisy chain out: female Hardware interfaces RS485A/B (pin 5, pin 3 ) power supply (pin 1, pin 6); DC return (pin 7) Daisy chain in Daisy chain out conforming with AISG Adjustment time (full range) 40 seconds (typical, depending on antenna type) Adjustment cycles >50,000 Temperature range -40°C to +60°C Protection class IP 24 Housing material Profile: Aluminum, coated Cover: Zinc diecast, coated varnished housing (RAL 7035, light gray) Bottom of RCU Termination Plug Weight 1.16 lb (525 g) Dimensions 7 x 2.4 x 2 inches (178 x 60 x 50 mm) 1) The protocol of the logical interface can be switched from Shipping dimensions 9.6 x 4 x 3.7 inches (245 x 102 x 93 mm) AISG 1.1 to 3GPP/AISG 2.0 and vice versa with a vendor Standards EN 60950-1 (Safety) specific command. Start-up operation of the RCU 860 10025 EN 55022 (Emission) is only possible in a RET system supporting AISG 1.1 and EN 55024 (Immunity) start-up operation of the RCU 860 10118 is only possible in a ETS 300019-1-4 (Environmental) st RET system supporting 3GPP/AISG 2.0. UL 60950-1; 1 edition Please note: If the Primary of the RETsystem does not Certifications CE, UL, FCC 15.107 Class B support the standard of the ‘logical interface ex factory’, the RCU must be switched to the appropriate standard of Order Information: the Primary before installation. Please contact Kathrein for Model Description further information. 860 10025 Remote control unit (AISG 1.1 start-up) 2) The tightening torque for attaching the connector must be 860 10118 Remote control unit (3GPP/AISG 2.0 start-up) 0.5–1.0 Nm (hand tightened). KATHREIN 860 10025, 860 10118 7 inches 2 inches (178 mm) (50 mm) Tested To Comply With FCC Standards This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 2.4 inches (1) This device may not cause harmful interference, and (2) this device must accept any interference (60 mm) received, including interference that may cause undesired operation. All specifications are subject to change without notice. 10853-G The latest specifications are available at www.kathrein-scala.com. 936.2849/d Kathrein Inc., Scala Division Post Office Box 4580 Medford, OR 97501 (USA) Phone: (541) 779-6500 Fax: (541) 779-3991 Email: communications@kathrein.com Internet: www.kathrein-scala.com Attaching the RCU Threaded attachment fitting ➊ Step 1 for the downtilt adjustment ➊ cap and the RCU. Remove the protective downtilt ➎ adjustment cap completely from Locking ring. ➋ ➋ the antenna. Downtilt adjustment spindle ➌ Remove the black locking ring ➋ with integrated downtilt by pulling it downward. ➋ degree scale. Check the phase shifter for proper function by turning the gear wheel Antenna tilt control housing. ➍ . The phase shifter will go ➎ smoothly between minimum and ➌ maximum tilt when functioning Gear wheel for the RCU. ➎ properly. Reset the downtilt to 0 degrees. Step 2 Avoid ingestion of mounting-paste Clean the thread surface. or contact with eyes. In case of contact with eyes rinse thoroughly Apply the mounting-paste evenly with plenty of water and seek onto the full circumference of the medical advice. Avoid long-term thread as illustrated in the figure. ➍ contact with skin. In case of contact with skin wash off with ➎ soap and water. For further information please read the ‘Safety data-sheet (91/155 EEC), Anti-Seize ‘High-Tech’ Assembly Paste different packing sizes’ by company WEICON GmbH & Co. KG, Königsberger Str. 225, D-48157 Münster, http://www.weicon.de Step 3 Push the attachment nut of the RCU down towards the RCU housing. Place the RCU carefully over The RCU must be kept the adjustment spindle . Be ➌ in vertical alignment sure the flat side of the spindle with the antenna during is aligned with the flat side of the antenna tilt control housing . installation or the ➍ downtilt adjustment Carefully push the RCU onto the spindle ➌ may be antenna until it is firmly seated. damaged. Step 4 To set the downtilt angle exactly you must look Hand tighten the RCU horizontally at the scale. The attachment nut (41 mm). lower edge of the gear wheel must be used for alignment Torque setting: 11 lb ft purposes. (15 Nm) In cases where a mechanical downtilt is Connect the RCU control installed do not set the cable. mechanical tilt more than 14 degrees or the unit may be damaged. All specifications are subject to change without notice. The latest specifications are available at www.kathrein-scala.com. Kathrein Inc., Scala Division Post Office Box 4580 Medford, OR 97501 (USA) Phone: (541) 779-6500 Fax: (541) 779-3991 Email: communications@kathrein.com Internet: www.kathrein-scala.com