Quad Output AC/DC Medical Power Supply, 70W IPD REL-70 Series REL-70 SERIES AC-DC OUTPUT SPECIFICATIONS Total Output Power at 50°C 50W Convection Cooled FEATURES: 70W Forced Air Cooled • RoHS Compliant • EN 60950-1 ITE Certification Output Voltage Centering Output 1: (All outputs ± 0.5% • Universal 85-264 VAC Input • EN 60601-1 Medical Certification Output 2,3,4: at 50% load) ± 5.0% • High Efficiency • Class B Emissions per EN 55011/22 Output Voltage Adjust Range Output 1: 95 - 105% • Advanced SMT Design • Harmonic Current per EN 61000-3-2 Load Regulation Output 1: 0.5% (10-100% • Compact 2.5 x 4.5" x 1.2" Size • EMC to EN 61000-6-2 & EN 60601-1-2 Output 2: 5.0% load change) • 2 Year Warranty • Optional Chassis and Cover (4001-5) 8.0% • Fits 1U Applications • One to Four Outputs (2001) 8.0% Output 3: 5.0% Output 4: 5.0% Source Regulation Outputs 1 – 4: 0.5% Cross Regulation Outputs 2 – 4: 5.0% Output Noise Outputs 1 – 4: 1.0% Turn on Overshoot None Transient Response Outputs 1 – 4 Voltage Deviation 5.0% Recovery Time 500µS Load Change 50% to 100% Output Overvoltage Protection Output 1: 110% to 150% OPEN FRAME CHASSIS/COVER Output Overpower Protection 110-160% rated Pout, cycle on/off, auto recovery Hold Up Time 16 mS min., Full Power, 85V Input SAFETY SPECIFICATIONS Start Up Time 4 Seconds, 120V Input Protection Class: I INPUT SPECIFICATIONS General Overvoltage Category: II Source Voltage 85 – 264 Volts AC Pollution Degree: 2 Frequency Range 47 – 63 Hz nd Underwriters UL 60950-1 2 Edition Peak Inrush Current 40A st Laboratories UL 60601-1 1 Edition Efficiency 78% Typ., Full Power, 230V, varies by model File E137708/E140259 Power Factor 0.95 (Full Power, 230V) CB Certificate per IEC 60950-1:2005 ENVIRONMENTAL SPECIFICATIONS nd 2 Edition +A1:2009 including all Ambient Operating 0 C to + 70 C National Deviations Temperature Range Derating: See Power Rating Chart CB Certificate per IEC 60601-1 (1988) Ambient Storage Temp. Range - 40 C to + 85 C nd 2 Edition A1, A2 Temperature Coefficient Outputs 1 – 4: 0.02%/ C CAN/CSA-C22.2 No. 60950-1-07, UL Recognition GENERAL SPECIFICATIONS nd 2 Edition Mark for Canada Dielectric Strength(13) CAN/CSA-C22.2 No. 601-1-M90 File E137708/E140259 Reinforced Insulation 5656 VDC, Primary to Secondary, 1 Sec. with updates 1 and 2 Basic Insulation 2121 VDC, Primary to Ground, 1 Sec. EN 60950-1/A1:2010 Operational Insulation 500 VDC, Secondary to Ground, 1 Sec. TUV EN 60601-1/A2:1995 Leakage Current <300uA Earth Leakage Current Power Fail Signal Logic low with input power failure 10 mS Low Voltage Directive minimum prior to Output 1 dropping 1% Remote Sense (singles only) 250mV compensation of output cable losses Mean-Time Between Failures 100,000 Hours min., MIL-HDBK-217F, 25° C, GB MODEL LISTING Weight 0.60 Lbs. Open Frame MODEL NO. OUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4 1.00 Lbs. Chassis and Cover REL-70-4001 +3.3V/6A +5V/5A +12V/2A(7) -12V/2A(7) ELECTROMAGNETIC COMPATIBILITY SPECIFICATIONS REL-70-4002 +5V/6A +3.3V/5A +12V/2A(7) -12V/2A(7) Electrostatic Discharge EN 61000-4-2 +/-8kV Contact Discharge REL-70-4003 +5V/6A +3.3V/5A +15V/2A(7) -15V/2A(7) +/-8kV Air Discharge REL-70-4004 +5V/6A -5V/5A +12V/2A(7) -12V/2A(7) Radiated Electromagnetic Field EN 61000-4-3 80MHz-2.5GHz, 10/m, 80% AM REL-70-4005 +5V/6A -5V/5A +15V/2A(7) -15V/2A(7) EFT/Bursts EN 61000-4-4 +/-2 kV REL-70-4006 +5V/6A +24V/2A +12V/2A(7) -12V/2A(7) REL-70-4007 +5V/6A +24V/2A +15V/2A(7) -15V/2A(7) Surges EN 61000-4-5 +/- 1 kV Common Mode REL-70-4009 6.7V/5A 5V/4A +15V/2A(7) -15V/2A(7) +/- 2 kV Differential Mode REL-70-3001 +5V/6A +12V/2A -12V/2A(7) Conducted Immunity EN 61000-4-6 .15 to 80MHz, 10V, 80% AM REL-70-3002 +5V/6A +15V/2A -15V/2A(7) Voltage Dips and Interruptions EN 61000-4-11 30% Reduction, 500ms REL-70-3003 +5.1V/6A +7.5V/2A -7.5V/2A(7) 95% Reduction, 10ms REL-70-3004 +3.3V/6A +7V/5A +12V/2A(7) 60% Reduction, 1s (Criteria B) REL-70-2001 +3.3V/6A +5V/5A 95% Reductions, 5000ms REL-70-2002 +5V/6A +12V/4A Voltage Interruptions EN 61000-4-11 95% Reduction, 5s REL-70-2003 +5V/6A +24V/2A Radiated Emissions EN 55011/22 Class B REL-70-2004 +12V/3A -12V/3A Conducted Emissions EN 55011/22 Class B REL-70-2005 +15V/3A -15V/2A Harmonic Current Emissions EN 61000-3-2 REL-70-2006 +5.5V/6A -5.5V/5A Voltage Fluctuations and Flicker EN 61000-3-3 REL-70-1001 2.5V/14A(1) NOTES REL-70-1002 3.3V/14A(1) Consult factory for alternate output configurations. REL-70-1003 5V/14A(1) Consult factory for positive, negative or floating outputs. REL-70-1004 12V/5.8A Refer to Applications Information for complete output power ratings. REL-70-1005 15V/4.7A All specifications are maximum at 25 C, 110W unless otherwise stated, may vary by REL-70-1006 24V/2.9A model and are subject to change without notice. REL-70-1007 28V/2.5A Specify optional chassis and cover when ordering. REL-70-1008 48V/1.5A www.trcelectronics.com/ipd TRC ELECTRONICS, INC. 1.888.612.9514 Quad Output AC/DC Medical Power Supply, 70W IPD REL-70 Series REL-70 MECHANICAL SPECIFICATIONS APPLICATIONS INFORMATION 1. Rated 10A with convection cooling. OPEN FRAME 2. Total power must not exceed 50 watts with convection cooling on open frame .65 (16.5) 3.20 (81.3) 4−40 models. MTG HOLE 3. Total power must not exceed 70 watts with 300LFM forced air cooling on open (2 PLACES) frame models. .80 (20.3) 4. Total power must not exceed 40 watts with convection cooling and chassis/cover 1.00 (25.4) 1.22 (31.0) option. MAX 5. Total power must not exceed 70 watts with 300LFM forced air cooling and chassis/cover option. P3 6. Each output can deliver its rated current but total output power must not exceed 1 (+) OUTPUT 1 maximum power as determined by the cooling method stated above. 2 (+) SENSE 3 (−) OUTPUT 1 7. Rated 1.5 A with convection cooling. 4 (−) SENSE 5 (−) P.F. RTN 8. Sufficient area must be provided around convection cooled power supplies to 6(+) P.F. SIG 3 P3 2 6 P2 allow natural movement of air to develop. 1 5 1 (−) OUTPUT 1 1 9. 300 linear feet per minute of airflow must be maintained one inch above any point 2 (−) OUTPUT 1 3 (−) OUTPUT 1 of the heatsink in the direction shown when forced air cooling is required. 4 (−) OUTPUT 1 3 5 (+) OUTPUT 1 2 10. This product is intended for use as a professionally installed component within 6 (+) OUTPUT 1 AC P1 7 (+) OUTPUT 1 INPUT information technology and medical equipment. N 8(+) OUTPUT 1 P2 11. A minimum load of 10% is required on output one to ensure proper regulation of V1 ADJUST GND remaining outputs. 1 12. Remote sense terminals may be used to compensate for cable losses up to SINGLE OUTPUT MODEL .128 DIA 250mV (single output models only). The use of a twisted pair is recommended as MTG HOLE (4 PLACES) well as a de-coupling capacitor (0.1 - 10µF) and a capacitor of 100µF/amp connected across the load side. 13. Peak to peak output ripple and noise is measured directly at the output terminals 4.50 (114.3) .15 (3.8) TYP 4.20 (106.7) of the power supply, without the use of the probe ground lead or retractable tip, 20 MHz bandwidth. P2 1 (−) OUTPUT 4 14. This product was type tested and safety certified using the dielectric strength test 1 2 (+) OUTPUT 4 voltages listed in Table V of UL 60601-1. In consideration of Clause 20.4g, care 3 (−) OUTPUT 3 2.20 (55.9) 4 (+) OUTPUT 3 must be taken to insure that the voltage applied to a reinforced insulation does P2 5 (−) OUTPUT 2 6 (+) OUTPUT 2 not overstress basic insualtion. Secondary to ground capacitors may need to be 7 (−) OUTPUT 1 L AC 8(+) OUTPUT 1 removed prior to performing a dielectric strength type test on the end product. It is P1 2.50 (63.5) INPUT N V1 ADJUST highly recommended that the DC test voltages litsed in DVB.1, Annex DVB are 1 P3 P3 GND not exceeded during a production-line dielectric strength test of the assembled 1 (−) P.F. RTN 2(+) P.F. SIG end product. Please consult factory for further information. MULTIPLE OUTPUT MODEL 15. This power supply has been safety approved and final tested using a DC dielectric strength test. Please consult factory before performing an AC dielectric .65 (16.5) 3.20 (81.3) 4−40 MTG HOLE strength test. (2 PLACES) 16. Maximum screw penetration into bottom chassis mounting holes is .100 inches. 17. Maximum screw penetration into side chassis mounting holes is .250 inches. 1.22 (31.0) 1.00 (25.4) MAX .80 (20.3) 18. To meet emissions specifications, all four mounting hole pads must be electrically connected to a common metal chassis. Chassis/cover option recommended. 19. This product includes only one fuse in the input circuit. In consideration of Clause 57.6 of UL 60601-1, a second fuse may be required in the end product. OPTIONAL CHASSIS/COVER MAXIMUM Output Power vs. Ambient Temperature 70 .25 (6.4) TYP 4.20 (106.7) F O RCE D AIR CO O L ING 60 50 4−40 .68 (17.3) C ON V E C T ION C OOL IN G MTG HOLE 40 (2 PLACES) 30 1.48 (37.6) 20 10 0 4.79 (121.6) 0 102030 40506070 .30 (7.6) 4.20 (106.7) A m b ie n t T e m p eratu re ( C ) Connector Specifications .23 (5.8) P1 AC Input .156 friction lock header mates with Tyco 640250-3 or 3 1 equivalent crimp terminal housing with Tyco 3-640706-1 or 2.20 (55.9) equivalent crimp terminal. P2 P2 DC Output .156 friction lock header mates with Tyco 770849-8 or 2 3 (Single) equivalent crimp terminal housing with Tyco 3-640707-1 or L P1 equivalent crimp terminal. 2.62 (66.5) N V1 P2 DC Output .156 friction lock header mates with Tyco 770849-8 or 1 4−40 P3 MTG HOLE (4 PLACES−BASE) (Multiple) equivalent crimp terminal housing with Tyco 3-640707-1 or 1 equivalent crimp terminal. ALL DIMENSIONS IN INCHES (MM) G Ground .187 quick disconnect terminal. P3 P.F./Sense .100 breakaway header mates with Molex 22-55-2061 or Recommended Air Flow Direction (Single) equivalent crimp terminal housing with Molex type 71851 or equivalent crimp terminal. 1 – Optimum 2 – Good 3 – Fair P3 Power Fail .100 breakaway header mates with Molex 50-57-9002 or (Multiple) equivalent crimp terminal housing with Molex type 71851 or equivalent crimp terminal. www.trcelectronics.com/ipd TRC ELECTRONICS, INC. 1.888.612.9514