FTA1100J Diesel Engine Fire Pump Controllers Product Description • MAIN SWITCH IN MANUAL • SYSTEM PRESSURE LOW • ENGINE RUNNING • ENGINE FAIL TO START • ENGINE TEMPERATURE HIGH • ENGINE OIL PRESSURE LOW • ENGINE OVERSPEED • ENGINE ALTERNATE ECM • ENGINE FUEL INJECTOR MALFUNCTION • FUEL LEVEL LOW • AUTOMATIC SHUTDOWN DISABLED • CHARGER MALFUNCTION • BATTERY #1 TROUBLE • BATTERY #2 TROUBLE • Minimum Run Timer / Off Delay Timer • Programmable Daylight Saving Time Option • Weekly Test Timer ® • Engine Run Time Meter Description – Firetrol combined automatic and manual • Digital Pressure Display Mark IIXG based diesel engine Ţ re pump controllers are • USB Host Controller and Port intended for starting and monitoring Ţ re pump diesel • Solid State Pressure Transducer engines. They are suitable for use with both mechanical • Data Log and electronic type engines. The controller is available for • Event Log (3000 events) 12 or 24 volt negative ground systems, using lead acid • Simultaneous Display of Battery Voltages, Charging or Nickel-Cadmium batteries. The controller monitors, Rates, AC Volts, Pressure and Alarm Messages displays and records Ţ re pump system information. • Disk Error Message • Disk Near Full Message Approvals – Firetrol Ţ re pump controllers are listed by • Pressure Error Message Underwriters’ Laboratories, Inc., in accordance with • Fail to Start Message UL218, Standard for Fire Pump Controllers, CSA, Standard • Low Suction Pressure Message for Industrial Control Equipment (cUL), and approved by • Crank Cycle Status Indication (Displays Cranking Bat- Factory Mutual. They are built to meet or exceed the tery, Number of Starting Attempts and Crank/Rest requirements of the approving authorities as well as Time Remaining) NEMA and the latest editions of NFPA 20, Installation • 300 psi (20.7 bars) wet parts (solid state pressure of Centrifugal Fire Pumps, and NFPA 70, National Electri- transducer, solenoid valve, plumbing) for fresh water cal Code. applications • NEMA Type 2 enclosure (IEC IP22) Standard Features – The following are included as stan- • Each standard controller comes with user set options dard with each controller: for: • AC Line & Battery circuit breakers • AC Power Loss Start • Interlock Alarm • Manual-Off-Auto selector switch • Low Pressure Aud. • Low Suction • Manual test push-button • Main Sw. Mis-Set • Manual Test • Two manual crank push-buttons • Pump Run Alarm • Remote Start • Two 10 Amp battery chargers with 4 stage charging • User DeŢ ned Input • Weekly Test Setup cycle, selectable AC voltage (110 / 220), selectable DC • Low Pump Rm Temp • Low Reservoir voltage (12 / 24), and selectable battery type (Lead • Relief Valve Open • High Fuel Level Acid, Ni-Cad 9/18 Cell, Ni-Cad 10/20 Cell) • High Reservoir • Door mounted display/interface panel featuring a 128 x 64 pixel backlit LCD graphical display, Membrane Type User Control Push-buttons and easy to read LED Indicators for: • AC POWER AVAILABLE • ALARM • MAIN SWITCH IN AUTO -CPL Contacts for remote indication, system Special Enclosures 115% over pressure (for use with PLD engines only) -T NEMA Type 3R (IEC IP22), Painted Steel -CTS Built-in low suction pressure alarm panel (Includes select- -E NEMA Type 4 (IEC IP 66), Painted Steel able auto/manual reset, audible, visible and remote alarms -F NEMA Type 4X (IEC IP66) #304 Stainless and mounted and wired pressure switch) Steel, Brushed Finish -EE Additional contacts for remote indication, engine trouble - 1 -FXP NEMA Type 4X (IEC IP66) #304 Stainless set provided as standard Steel, Painted Finish -EF Additional contacts for remote indication, main switch -FD NEMA Type 4X (IEC IP66) #316 Stainless mis-set - 1 set provided as standard Steel, Brushed Finish 1 -EH Contacts for remote indication, relief valve discharge -FDB NEMA Type 4X (IEC IP66) #316 Stainless 1 -EJ Audible & Visible ţ ow meter on alarm Steel, 12 Gauge, Seam Welded, 1 -EK Contacts for remote indication, ţ ow meter on (Requires Brushed Finish option -EJ) -FDP NEMA Type 4X (IEC IP66) #316 Stainless -JR Visible jockey pump running indication Steel, Painted Finish -JT Audible and visible jockey pump trouble indication -G NEMA Type 12 (IEC IP54) 1 -LC Contacts for remote indication, high fuel level 1 -LD Audible & Visible fuel spill alarm Mounting Legs 1 -LE Contacts for remote indication, fuel spill (Requires option -N31 Standard 12” Mounting Legs -LD) -N31S 12” Mounting Legs, Stainless Steel 1 -LG Contacts for remote indication, reservoir high -PE Contacts for remote indication, low system pressure Anti-Condensation Space Heaters (Pump On Demand) -H 120 Volt Space Heater -J 120 Volt Space Heater with Thermostat Miscellaneous -K 120 Volt Space Heater with Humidistat -AZ Low pump room temperature switch, mounted and wired -L 240 Volt Space Heater -BA 220-240 Volt operation -M 240 Volt Space Heater with Thermostat -EL Series pumping, high zone controller -N 240 Volt Space Heater with Humidistat -EM Series pumping, mid zone controller -EN Series pumping, low zone controller Pressure Transducers, Solenoid Valves, Plumbing -IEC CE Marking with Externally Mounted Wet Parts -B 0-600 psi (0-41.4 bars) wet parts for fresh water applications -IECI CE Marking (Internal Wet Parts) -C 0-300 psi (0-20.7 bars) wet parts for copper corrosive -OSP OSHPD Seismic CertiŢ cation (State of California) (Requires applications Option -SEI) -D 0-600 psi (0-41.4 bars) wet parts for copper corrosive -S Tropicalization applications -SEI Seismic CertiŢ cation (in accordance with IBC) -USBX External USB Port Alarms -ZPA Customized, annual service display message (factory -AC Additional contacts for remote indication, engine running - 2 programmed) sets provided as standard -ZPN Serial Modbus RTU over Ethernet TCP/IP -AJ Contacts for remote indication, engine overspeed using 5150 Connectivity Module -AK Contacts for remote indication, low oil pressure -ZPM Serial Modbus RTU over 2-wire or 4-wire RS485 -AL Contacts for remote indication, high water temperature -AM Contacts for remote indication, engine failed to start 2 FTA1100-K1 Low fuel level switch, 16” max insertion length -AN Contacts for remote indication, battery / charger failure FTA1100-K1-X High/Low fuel level switch - specify levels/tank -AP Contacts for remote indication, main switch in manual dimensions -AR Contacts for remote indication, main switch in off 2 FTA1100-K2 Low fuel level switch, 25” max. insertion length -AS Contacts for remote indication, main switch in auto 1 2 FTAK21 380-480 volt operation (transformer) -AT Contacts for remote indication, pump room trouble Export packaging (Wooden crating to conform to IPPC Standards) -AV Contacts for remote indication, low pump room 1 temperature 1 -AW Contacts for remote indication, reservoir low 1 1 - Initiating switches by others -AY Contacts for remote indication, low suction pressure 2 - Shipped loose for installation by the customer -COM Visible low suction pressure alarm, Manual reset only (Includes reset push-button, initiating 1 pressure switch not included)