D GND Loc Loc Rmt Rmt Ethernet Extenders over Copper Wire Power1 Power 2 Power 3 ED3141 Series Hardened 10/100BASE-TX Ethernet Extender Overview The ED3141 is a point-to-point Ethernet Wide Temp ITS UL508 Extender designed to operate in harsh environments that efficiently extends 10/100 Ethernet circuits to over 300meters (984feet) at 50Mbps using existing cross-over pair copper wire. The ED3141 functions at temperatures ranging from -40°C to 75°C (-40°F to 167°F) and is tested for functional operation @ -40°C to 85°C (-40°F to 185°F). The ED3141 will allow Ethernet connectivity in existing facilities without pulling extra cable. This is the perfect solution to Ethernet on the factory floor where systems have been upgraded from slower serial communications to Ethernet networking. Installation is easy with a single switch setting, one end is set for local and the other remote. The ED3141 is used in pairs to extend Ethernet connectivity over existing voice grade copper wire. Features Complies with NEMA TS1 & TS2 Environmental requirements Ethernet Extender (RJ-11 and Terminal Block) Port: Symmetrical for Traffic control equipment on the VDSL, High-speed Full-duplex 50Mbps communications ISA 12.12.01, Class 1, Division 2 Classified for use in hazardous link over existing copper Telephone line locations Ten speeds with speed indicator LEDs on front panel of unit, Complies with IEC61000-6-2 EMC Generic standard immunity Up to 50Mbps@about 300meters (984ft.), for Industrial environment Down to 1Mbps@about 1,900meters (6,232ft.) Operates transparent to higher layer protocols such as TCP/IP Redundant power inputs with Terminal Block and DC Jack Ethernet Port: 10/100Mbps-Full/Half-duplex, Auto-Negotiation, -40°C to 75°C (-40°F to 167°F) operating temperature range Auto-MDI/MDIX Hardened aluminum case Support DIP switch to select Local or Remote side Supports DIN-Rail Panel Rack Mounting installation Ordering Information ED3141-00Z 10/100BASE-TX Hardened Ethernet Extender Power Input Interface: (Z) = B : Terminal Block & DC Jack Power Supply: (Optional) *Option A - The Terminal Block type external power supply are not included. Please order the following part numbers, as required: DR-30-24, DR-60-24, DR-75-24, DR-120-24 or 41-136046-X X=1,2,3,4,5 **Option B - The external power adapter and power cord are not included. Please order the following part numbers, as required: 41-136044-X X=1,2,3,4,5 Installation Type : Optional Panel mount kit, part number: KP-AA96-480 Diagrams 50mm 110mm + + Front Side Back Top Bottom 3-13 135mm - - Ethernet Extenders Accessories Specifications Technology Environment Standards: Operating Temperature: IEEE802.3 10BASE-T, IEEE802.3u 100BASE-TX, IEEE802.3x, -40°C to 75°C (-40°F to 167°F) Ethernet over VDSL Tested @ -40°C to 85°C (-40°F to 185°F) Protocols: Storage Temperature: Transparent to higher layer protocols -40°C to 85°C (-40°F to 185°F) Processing Type: Ambient Relative Humidity: Half-duplex back-pressure and IEEE802.3x Full-duplex flow control 5% to 95% (non-condensing) Power Regulatory Approvals: Input: ISO: Input Voltage: 12 to 30VDC (Terminal Block);12VDC (DC Jack) Manufactured in an ISO9001 facility Power Consumption: Safety: 4.2W Max. 0.35A@12VDC, 0.175A@24VDC Overload Current Protection: UL508 Present ISA 12.12.01, Class 1, Division 2 Classified for use in hazardous locations Reverse Polarity Protection: EMI: Present FCC Part 15, Class A Mechanical EN61000-6-3 Casing: EN55022 Aluminum case EN61000-3-2 IP30 EN61000-3-3 Dimensions: EMS: 50mm (W) x 110mm (D) x 135mm (H) EN61000-6-2 (1.97" (W) x 4.33" (D) x 5.31" (H)) EN61000-4-2 (ESD Standards) Weight: 0.8Kg (1.76lbs.) Contact: + / - 4KV; Criteria B Installation: Air: + / - 8KV; Criteria B DIN-Rail (Top hat type 35mm), Panel Rack Mounting EN61000-4-3 (Radiated RFI Standards) Interface 10V/m, 80 to 1000MHz; 80% AM Criteria A Ethernet Port: EN61000-4-4 (Burst Standards) Port: One RJ-45 port, 10/100BASE-TX Full/Half-duplex Signal Ports: + / - 4KV; Criteria B Auto-Negotiation, Auto-MDI/MDIX D.C. Power Ports: + / - 4KV; Criteria B Speed: 10/100Mbps EN61000-4-5 (Surge Standards) Distance: 100meters (328ft.) Signal Ports: + / - 1KV; Line-to-Line; Criteria B Cable: 10BASE-T: UTP CAT. 3, 4, 5 (2-pair wire) D.C. Power Ports: + / - 0.5KV; Line-to-earth; Criteria B 100BASE-TX: UTP CAT. 5 (2-pair wire) EN61000-4-6 (Induced RFI Standards) Signal Ports: 10Vrms @ 0.15~80MHz; 80% AM Criteria A Ethernet Extender Port: Port: One RJ-11 and Terminal Block port D.C. Power Ports: 10Vrms @ 0.15~80MHz; 80% AM Criteria A EN61000-4-8 (Magnetic Field Standards) Speed: 1/3/5/10/15/20/25/30/40/50Mbps 30A/m @ 50, 60Hz; Criteria A Distance: 1900meters (6,232ft.) Environmental Test Compliance: Cable: Telephone line 24 AWG (0.5mm diameter, 1-pair wire) or larger IEC60068-2-6 Fc (Vibration Resistance) DIP switch: 5g @ 10~150Hz, Amplitude 0.35mm (Operation/Storage/Transport) One DIP switch: Local (CO) or Remote (CPE) IEC60068-2-27 Ea (Shock) LED Indicators: 25g @ 11ms (Half-Sine Shock Pulse; Operation) Per Unit: Power Status (Power) 50g @ 11ms (Half-Sine Shock Pulse; Storage/Transport) Per Port: 10/100TX: Link/Activity, Full-duplex IEC60068-2-32 Ed (Free Fall) Line: Error, Link, Local, Remote 1M (3.281ft.) LED Speed Distance 1 Green 1 Mbps 1,900m (6,232 ft.) Amber 3 Mbps 1,800m (5,904 ft.) 2 Green 5 Mbps 1,600m (5,249 ft.) Amber 10Mbps 1,400m (4,593 ft.) 3 Green 15Mbps 1,200m (3,936 ft.) Amber 20Mbps 1,000m (3,280 ft.) 4 Green 25Mbps 800m (2,624 ft.) Amber 30Mbps 700m (2,296 ft.) Green 40Mbps 600m (1,968 ft.) 5 50Mbps 300m ( 984 ft.) Amber NOTE: All speed selections are Symmetrical on the DSL and Full-duplex on the Ethernet. 3-14 2-11