EPSON ELPMBC01
Specifications
Color
White
Features
- Designed to allow cable management
- Features a pipe fitting, threaded on both ends
- Includes an 8" – 11" adjustable extension (adjusts in 1-inch increments)
- Offers notched ends for use with set screws to provide added safety and security
Datasheet
Extracted Text
Installation and Assembly:
Adjustable Extension Column (Pipe) 8" - 11"
Model: ELPMBC01
This product is UL Listed. It must be
installed by a qualified professional
�
installer.
Maximum UL Load Capacity: 500 lb (227 kg)
Manufactured by Peerless Industries, Inc.
3215 W. North Ave. • Melrose Park, IL 60160 • (800) 865-2112 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com
NOTE: Read entire instruction sheet before you start installation and assembly.
WARNING
• Do not begin to install your product until you have read and understood the instructions and warnings contained in this
Installation Sheet. If you have any questions regarding any of the instructions or warnings, call Peerless customer care
at 1-800-729-0307.
• This product should only be installed by someone of good mechanical aptitude, has experience with basic building
construction, and fully understands these instructions.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hard-
ware and components.
• Never exceed the Maximum UL Load Capacity.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding
power. See suggested torque values where applicable within these instructions.
• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal
injury.
• When installing or adjusting the ceiling mount, do not use adhesives, lubricants, or oils to prevent the screws from
loosening. If you use adhesives, lubricants, or oils to prevent the screws from loosening, the casing may crack and the
projector may fall, causing serious injury and damage to the projector.
Tools Needed for Assembly
• phillips screwdriver
Table of Contents
Parts List .............................................................................................................................................................................. 3
Installation to Ceiling Plate ................................................................................................................................................... 4
Adjustment of Extension Column .......................................................................................................................................... 5
Warranty ............................................................................................................................................................................... 6
2 of 6 ISSUED: 03-06-08 SHEET #: 154-9009-2 07-10-08
Visit the Peerless Web Site at www.peerlessmounts.com For Technical Support Contact Peerless Mounts at 1-800-729-0307 or 708-865-8870.
Before you start check the parts list to ensure all of
the parts shown are included.
Parts List
Description Qty. Part Number
A extension column 1 154-2093
NOTE: Actual parts may appear slightly different
than illustrated.
A
Outer Column
M8 x 10 mm phillips screw
Inner Column
3 of 6 ISSUED: 03-06-08 SHEET #: 154-9009-2 07-10-08
Visit the Peerless Web Site at www.peerlessmounts.com For Technical Support Contact Peerless Mounts at 1-800-729-0307 or 708-865-8870.
Installation to Ceiling Plate
WARNING
• Installer must verify that the supporting surface will safely support four times the combined weight of all attached
equipment and hardware.
• Extension column (A) must be fully threaded (six or seven full turns) onto threaded fitting in ceiling plate and then
locked with M5 x 10 mm screw (not included).
Screw extension column to ceiling plate (not included) as shown in fig. 1.1. Align the slot with one of the four holes
1 in the ceiling plate (not included) and secure extension column with a M5 x 10 mm screw (not included) as shown in
fig. 1.2 and detail 1.
*NOTE: Slotted set screws (not included) are used to jam against the threads of each connecting joint to prevent any
excess movement. Do not overtighten screws; overtightening screws will damage threads making it difficult to
separate the products.
UL LISTED ELPMBP01, ELPMBP02,
ELPMBP03 AND CMJ OR ACC SERIES
CEILING MOUNTS (SOLD SEPARATELY)
CEILING PLATE
(NOT INCLUDED)
SLOT
SLOT
M5 x 10 mm SCREW
(NOT INCLUDED)
A
DETAIL 1
*SET SCREWS
fig. 1.1
(NOT INCLUDED)
PROJECTOR MOUNT (NOT SHOWN)
UL LISTED ELPMBPRG, ELPMBPJF AND PRG
OR PJF SERIES (SOLD SEPARATELY)
M5 x 10 mm SCREW
(NOT INCLUDED)
A
fig. 1.2
4 of 6 ISSUED: 03-06-08 SHEET #: 154-9009-2 07-10-08
Visit the Peerless Web Site at www.peerlessmounts.com For Technical Support Contact Peerless Mounts at 1-800-729-0307 or 708-865-8870.
Adjustment of Extension Column
WARNING
• Extension column (A) must be fully threaded (six or seven full turns) onto threaded fitting in ceiling plate and then
locked with M5 x 10 mm screw.
Skip to step 3 if adjustment is not required.
Remove M8 x 10 mm phillips screw from set hole in extension column (A) as shown in fig. 2.1. Slightly loosen
2 M8 x 10 mm phillips screw in hook slot until inner column is loose. Rotate inner column left and slide down in to
desired hook slot as shown in fig. 2.2 and 2.3. Securely tighten M8 x 10 mm phillips screw in hook slot. Fasten
M8 x 10 mm phillips screw into set hole and inner column and retighten M8 x 10 mm phillips screw in hook slot as
shown in fig. 2.1.
WARNING
• Do not loosen M8 x 10 mm screw to point of
disengagement. Hold inner column securely while
M8 x 10 MM
adjusting M8 x 10 mm screw. Tighten fasteners
PHILLIPS SCREW
securely.
SET HOLE
A
INNER COLUMN
fig. 2.1
M8 x 10 MM
PHILLIPS SCREW
M8 x 10 MM
PHILLIPS SCREW
HOOK SLOT
INNER COLUMN
fig. 2.2 fig. 2.3
5 of 6 ISSUED: 03-06-08 SHEET #: 154-9009-2 07-10-08
Visit the Peerless Web Site at www.peerlessmounts.com For Technical Support Contact Peerless Mounts at 1-800-729-0307 or 708-865-8870.
LIMITED FIVE-YEAR WARRANTY
3HHUOHVV,QGXVWULHV,QFHVWDEOLVKHVDZDUUDQW\SHULRGRIÀYH\HDUVIRUSURGXFWVPDQXIDFWXUHGRUVXSSOLHGE\3HHUOHVV7KLVSHULRGFRPPHQFHVIURPWKHGDWH
RIVDOHRIWKHSURGXFWWRWKHRULJLQDOFRQVXPHUEXWZLOOLQQRFDVHODVWIRUPRUHWKDQVL[\HDUVDIWHUWKHGDWHRIWKHSURGXFWҋVPDQXIDFWXUH'XULQJWKHZDUUDQW\
SHULRGVXFKSURGXFWVZLOOEHIUHHIURPGHIHFWVLQPDWHULDODQGZRUNPDQVKLSSURYLGHGWKH\DUHLQVWDOOHGDQGXVHGLQFRPSOLDQFHZLWKWKHLQVWUXFWLRQVHVWDEOLVKHGE\
3HHUOHVV,QGXVWULHV,QF6XEMHFWWRDSSOLFDEOHOHJDOUHTXLUHPHQWVGXULQJWKHZDUUDQW\SHULRG3HHUOHVVZLOOUHSDLURUUHSODFHRUUHIXQGWKHSXUFKDVHSULFHRIDQ\
VXFKSURGXFWZKLFKIDLOVWRFRQIRUPZLWKWKLVZDUUDQW\
$Q\RWKHUZDUUDQWLHVSUHVFULEHGE\WKHODZZKLFKPD\DSSO\ZLWKUHVSHFWWRVXFKSURGXFWVDOVRDUHOLPLWHGLQGXUDWLRQWRWKHZDUUDQW\SHULRGVSHFLÀHGLQWKLV/LPLWHG
)LYH
Frequently asked questions
What makes Elite.Parts unique?

What kind of warranty will the ELPMBC01 have?

Which carriers does Elite.Parts work with?

Will Elite.Parts sell to me even though I live outside the USA?

I have a preferred payment method. Will Elite.Parts accept it?

Why buy from GID?

Quality
We are industry veterans who take pride in our work

Protection
Avoid the dangers of risky trading in the gray market

Access
Our network of suppliers is ready and at your disposal

Savings
Maintain legacy systems to prevent costly downtime

Speed
Time is of the essence, and we are respectful of yours
What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods