Metallized Polypropylene Film Capacitors (MKP) B32 620 Plastic Case B32 621 MKP stacked-film capacitors Smallest possible dimensions Construction � Dielectric: polypropylene � Stacked-film technology � Plastic case (UL 94 V-0) � Epoxy resin sealing Features � Very high pulse strength � Very good self-healing properties Dimensions in mm � Smallest possible dimensions � High contact reliability Lead spacing Diameter d Type 1 ± 0,4 Typical applications 7,5 0,5 B 32 620 � Energy-saving lamps 1) 10 0,5 /0,6 B 32 621 � TV S-correction 1) 0,5 mm for capacitor width b = 4 mm � High pulse load applications � AC applications Terminals � Parallel wire leads, tinned � Also available with (3,2 ± 0,3) mm lead length Marking Manufacturer’s logo, lot number, style and type (P621) for lead spacing 10 mm, style (MKP) for lead spacing 7,5 mm, rated capacitance (coded), capacitance tolerance (code letter), rated dc voltage, date of manufacture (coded) Delivery mode Bulk (untaped) Taped (Ammo pack or reel) For notes on taping, refer to chapter “Taping and packing”, page 274. 117 12/00 MKP B 32 620 B 32 621 Overview of available types Lead spacing 7,5 mm 10 mm Type B 32 620 B 32 621 Page 119 121 0,47 nF 0,68 nF 1,0 nF 1,5 nF 2,2 nF 3,3 nF 4,7 nF 6,8 nF 10 nF 15 nF 22 nF 33 nF 47 nF 68 nF 0,10 µF 0,15 µF 0,22 µF 118 12/00 160 Vdc 90 Vac 250 Vdc 140 Vac 400 Vdc 200 Vac 630 Vdc 400 Vac 1000 Vdc 500 Vac 1000 Vdc 600 Vac 160 Vdc 90 Vac 250 Vdc 140 Vac 400 Vdc 200 Vac 630 Vdc 400 Vac 1000 Vdc 500 Vac B32 620 MKP 7,5 Ordering codes and packing units, lead spacing 7,5 mm 1) V C Maximum Ordering code Packing units (pcs) R R (V dimensions rms Ammo Reel Untaped f ≤ 1 kHz) b × h × l (mm) pack 160 Vdc 22 nF 3,0 × 8,0 × 10,0 B32620-A5223-+ 2600 2400 2000 *** (90 Vac) 33 nF 4,0 × 8,5 × 10,0 B32620-A5333-+ 2000 1800 1500 *** 47 nF 4,0 × 8,5 × 10,0 B32620-A5473-+ 2000 1800 1500 *** 68 nF 5,0 × 10,5 × 10,0 B32620-A5683-+ 1600 1400 1000 *** 0,10 µF5,0 × 10,5 × 10,0 B32620-A5104-+ 1600 1400 1000 *** 0,15 µF6,0 × 12,0 × 10,3 B32620-A5154-+ 1300 1100 750 *** 250 Vdc 22 nF 4,0 × 8,5 × 10,0 B32620-A3223-+ 2000 1800 1500 *** (140 Vac) 33 nF 4,0 × 8,5 × 10,0 B32620-A3333-+ 2000 1800 1500 *** 47 nF 5,0 × 10,5 × 10,0 B32620-A3473-+ 1600 1400 1000 *** 68 nF 5,0 × 10,5 × 10,0 B32620-A3683-+ 1600 1400 1000 *** 0,10 µF6,0 × 12,0 × 10,3 B32620-A3104-+ 1300 1100 750 *** 400 Vdc 6,8 nF 4,0 × 8,5 × 10,0 B32620-A4682-+ 2000 1800 1500 *** (200 Vac) 10 nF 4,0 × 8,5 × 10,0 B32620-A4103-+ 2000 1800 1500 *** 15 nF 5,0 × 10,5 × 10,0 B32620-A4153-+ 1600 1400 1000 *** 22 nF 5,0 × 10,5 × 10,0 B32620-A4223-+ 1600 1400 1000 *** 33 nF 6,0 × 12,0 × 10,3 B32620-A4333-+ 1300 1100 750 *** 630 Vdc 1,5 nF 4,0 × 8,5 × 10,0 B32620-A6152-+ 2000 1800 1500 *** (400 Vac) 2,2 nF 4,0 × 8,5 × 10,0 B32620-A6222-+ 2000 1800 1500 *** 3,3 nF 4,0 × 8,5 × 10,0 B32620-A6332-+ 2000 1800 1500 *** 4,7 nF 4,0 × 8,5 × 10,0 B32620-A6472-+ 2000 1800 1500 *** 6,8 nF 5,0 × 10,5 × 10,0 B32620-A6682-+ 1600 1400 1000 *** 10 nF 5,0 × 10,5 × 10,0 B32620-A6103-+ 1600 1400 1000 *** 15 nF 6,0 × 12,0 × 10,3 B32620-A6153-+ 1300 1100 750 *** Capacitance tolerance: ± 20 % = ˆ M, ± 10 % = ˆ K, ± 5 % = ˆ J 1) + Code letter for capacitance tolerance *** Code number for packing: Ammo pack = 289, reel = 189 The ordering code for untaped components ends after the tolerance code letter. For capacitors with 3,2 mm lead length, append code number “3” to the tolerance code, e.g.: B32620-A5104-K3 119 12/00 MKP B32 620 7,5 Ordering codes and packing units, lead spacing 7,5 mm 1) V C Maximum Ordering code Packing units (pcs) R R (V dimensions rms Ammo Reel Untaped f ≤ 1 kHz) b × h × l (mm) pack 1000 Vdc 1,5 nF 4,0 × 8,5 × 10,0 B32620-A152-+ 2000 1800 1500 *** (500 Vac) 2,2 nF 4,0 × 8,5 × 10,0 B32620-A222-+ 2000 1800 1500 *** 3,3 nF 5,0 × 10,5 × 10,0 B32620-A332-+ 1600 1400 1000 *** 4,7 nF 5,0 × 10,5 × 10,0 B32620-A472-+ 1600 1400 1000 *** 6,8 nF 6,0 × 12,0 × 10,3 B32620-A682-+ 1300 1100 750 *** 1000 Vdc 470 pF 4,0 × 8,5 × 10,0 B32620-J471-+ 2000 1800 1500 *** (600 Vac) 680 pF 5,0 × 10,5 × 10,0 B32620-J681-+ 1600 1400 1000 *** 1,0 nF 5,0 × 10,5 × 10,0 B32620-J102-+ 1600 1400 1000 *** 1,5 nF 5,0 × 10,5 × 10,0 B32620-J152-+ 1600 1400 1000 *** 2,2 nF 5,0 × 10,5 × 10,0 B32620-J222-+ 1600 1400 1000 *** 3,3 nF 5,0 × 10,5 × 10,0 B32620-J332-+ 1600 1400 1000 *** 4,7 nF 6,0 × 12,0 × 10,3 B32620-J472-+ 1300 1100 750 *** Capacitance tolerance: ± 20 % = ˆ M, ± 10 % = ˆ K, ± 5 % = ˆ J 1) + Code letter for capacitance tolerance *** Code number for packing: Ammo pack = 289, reel = 189 The ordering code for untaped components ends after the tolerance code letter. For capacitors with 3,2 mm lead length, append code number “3” to the tolerance code, e.g.: B32620-A152-K3 120 12/00 B32 621 MKP 10 Ordering codes and packing units, lead spacing 10 mm 1) V C Maximum Ordering code Packing units (pcs) R R (V dimensions rms Ammo Reel Untaped f ≤ 1 kHz) b × h × l (mm) pack 160 Vdc 47 nF 4,0 × 7,0 × 13,0 B32621-A5473-+ 1000 1700 1000 *** (90 Vac) 68 nF 4,0 × 9,0 × 13,0 B32621-A5683-+ 1000 1700 1000 *** 0,10 µF5,0 × 11,0 × 13,0 B32621-A5104-+ 830 1300 1000 *** 0,15 µF5,0 × 11,0 × 13,0 B32621-A5154-+ 830 1300 1000 *** 0,22 µF6,0 × 12,0 × 13,0 B32621-A5224-+ 680 1100 1000 *** 250 Vdc 2,2 nF 4,0 × 7,0 × 13,0 B32621-A3222-+ 1000 1700 1000 *** (140 Vac) 3,3 nF 4,0 × 9,0 × 13,0 B32621-A3332-+ 1000 1700 1000 *** 4,7 nF 4,0 × 9,0 × 13,0 B32621-A3472-+ 1000 1700 1000 *** 6,8 nF 4,0 × 9,0 × 13,0 B32621-A3682-+ 1000 1700 1000 *** 10 nF 4,0 × 9,0 × 13,0 B32621-A3103-+ 1000 1700 1000 *** 15 nF 4,0 × 9,0 × 13,0 B32621-A3153-+ 1000 1700 1000 *** 22 nF 4,0 × 9,0 × 13,0 B32621-A3223-+ 1000 1700 1000 *** 33 nF 4,0 × 9,0 × 13,0 B32621-A3333-+ 1000 1700 1000 *** 47 nF 4,0 × 9,0 × 13,0 B32621-A3473-+ 1000 1700 1000 *** 68 nF 5,0 × 11,0 × 13,0 B32621-A3683-+ 830 1300 1000 *** 0,10 µF6,0 × 12,0 × 13,0 B32621-A3104-+ 680 1100 1000 *** 400 Vdc 10 nF 4,0 × 9,0 × 13,0 B32621-A4103-+ 1000 1700 1000 *** (200 Vac) 15 nF 4,0 × 9,0 × 13,0 B32621-A4153-+ 1000 1700 1000 *** 22 nF 5,0 × 11,0 × 13,0 B32621-A4223-+ 830 1300 1000 *** 33 nF 5,0 × 11,0 × 13,0 B32621-A4333-+ 830 1300 1000 *** 47 nF 6,0 × 12,0 × 13,0 B32621-A4473-+ 680 1100 1000 *** 630 Vdc 2,2 nF 4,0 × 7,0 × 13,0 B32621-A6222-+ 1000 1700 1000 *** (400 Vac) 3,3 nF 4,0 × 9,0 × 13,0 B32621-A6332-+ 1000 1700 1000 *** 4,7 nF 4,0 × 9,0 × 13,0 B32621-A6472-+ 1000 1700 1000 *** 6,8 nF 4,0 × 9,0 × 13,0 B32621-A6682-+ 1000 1700 1000 *** 10 nF 4,0 × 9,0 × 13,0 B32621-A6103-+ 1000 1700 1000 *** 15 nF 5,0 × 11,0 × 13,0 B32621-A6153-+ 830 1300 1000 *** 22 nF 6,0 × 12,0 × 13,0 B32621-A6223-+ 680 1100 1000 *** 33 nF 6,0 × 12,0 × 13,0 B32621-A6333-+ 680 1100 1000 *** 1000 Vdc 2,2 nF 4,0 × 7,0 × 13,0 B32621-A222-+ 1000 1700 1000 *** (500 Vac) 3,3 nF 4,0 × 9,0 × 13,0 B32621-A332-+ 1000 1700 1000 *** 4,7 nF 4,0 × 9,0 × 13,0 B32621-A472-+ 1000 1700 1000 *** 6,8 nF 5,0 × 11,0 × 13,0 B32621-A682-+ 830 1300 1000 *** 10 nF 6,0 × 12,0 × 13,0 B32621-A103-+ 680 1100 1000 *** Capacitance tolerance: ± 20 % = ˆ M, ± 10 % = ˆ K, ± 5 % = ˆ J 1) + Code letter for capacitance tolerance *** Code number for packing: Ammo pack = 289, reel = 189 The ordering code for untaped components ends after the tolerance code letter. For capacitors with 3,2 mm lead length, append code number “3” to the tolerance code, e.g.: B32621-A5473-K3 121 12/00 MKP B 32 620 B 32 621 Technical data Climatic category 55/100/56 in accordance with IEC 60068-1 Lower category temperature T − 55 °C min Upper category temperature T + 100 °C max Damp heat test 56 days/40 °C/93 % relative humidity Limit values after damp Capacitance change |∆C/C| ≤ 3 % −3 heat test Dissipation factor change ∆ tan δ ≤ 0,5 ⋅ 10 (at 1 kHz) −3 ≤ 1,0 ⋅ 10 (at 10 kHz) Insulation resistance R ≥ 50 % of minimum is as-delivered values Reliability: Reference conditions 0,5 ⋅ V ; 40 °C R −9 Failure rate 1 ⋅ 10 /h = 1 fit For a conversion table for other operating conditions and tem- peratures, refer to chapter “Quality assurance”, page 327. Service life 200 000 h Failure criteria: Total failure Short circuit or open circuit Failure due to variation Capacitance change |∆C/C| > ±10 % of parameters Dissipation factor tan δ 4 ⋅ upper limit values Insulation resistance R < 1500 MΩ is DC test voltage 1,6 ⋅ V , 2 s R Category voltage V T ≤ 85 °C: V = 1,0 ⋅ V or 1,0 ⋅ V C C R rms Operation with dc voltage or T = 100 °C: V = 0,7 ⋅ V or 0,7 ⋅ V C R rms ac voltage V up to 1 kHz rms −3 Dissipation factor tan δ (in 10 ) C ≤ 0,1 µF0,1 µF < C ≤ 0,22 µF R R at 20 °C at 1 kHz – 1,0 (upper limit values) 10 kHz – 1,5 100 kHz 4,0 – Insulation resistance R 100 GΩ is or time constant τ = C ⋅ R R is at 20 °C, rel. humidity ≤ 65 % (minimum as-delivered values) 122 12/00 0,47 nF 1,5 nF 2,2 nF 10 nF 33 nF 0,10 µF 0,22 µF B32 620 MKP B32 621 Im pedance Z KMK0680-7 4 10 versus mΩ frequency f (typical values) Z 3 10 5 2 10 5 1 10 4 5 6 7 8 10 5 10 510 510 Hz 10 f Pulse handling capability Maximum permissible voltage change per unit of time for non-sinusoidal voltages (pulse, sawtooth) V Max. rate of voltage rise V /τ in V/µs (for V = V ) R pp pp R Lead spacing 7,5 mm 10 mm 160 Vdc 750 600 250 Vdc 1200 900 400 Vdc 1500 1050 630 Vdc 2700 1800 1000 Vdc (500 Vac) 3200 2400 1000 Vdc (600 Vac) 4000 − For V < V , the permissible voltage rise rate value V /τ may be multiplied by the factor V /V . pp R pp R pp Also refer to the calculation example in chapter “General technical information”, page 302. 2 V Pulse characteristic k in V /µs (forV ≤ V ) R 0 pp R Lead spacing 7,5 mm 10 mm 160 Vdc 240 000 190 000 250 Vdc 600 000 450 000 400 Vdc 1 200 000 840 000 630 Vdc 3 400 000 2 250 000 1000 Vdc (500 Vac) 6 400 000 4 800 000 1000 Vdc (600 Vac) 8 000 000 − 123 12/00 MKP B32 620 7,5 Permissible ac voltage V versus frequency f rms Lead spacing 7,5 mm 160 Vdc / 90 Vac 250 Vdc / 140 Vac KMK0744-H KMK0550-E 1000 1000 V V ac ac V V rms rms 500 500 100 100 50 50 22 nF 22 nF 0,10 µF 0,1 µF 0,15 µF 10 10 2 3 4 5 6 2 3 4 5 6 10 10 10 10 Hz 10 10 10 10 10 Hz 10 f f 400 Vdc / 200 Vac 630 Vdc / 400 Vac KMK0553-4 KMK0554-C 1000 1000 V V ac ac V V rms rms 500 500 100 100 1,5 nF 6,8 nF 3,3 nF 50 50 15 nF 6,8 nF 33 nF 15 nF 10 10 2 3 4 5 6 2 3 4 5 6 10 10 10 10 Hz 10 10 10 10 10 Hz 10 f f 124 12/00 B32 620 MKP 7,5 Permissible ac voltage V versus frequency f rms Lead spacing 7,5 mm 1000 Vdc/ 500 Vac 1000 Vdc/ 600 Vac KMK0560-L KMK0651-T 1000 1000 V ac Vac V rms V rms 500 500 0,47 nF 1,5 nF 1,0 nF 6,8 nF 2,2 nF 100 100 4,7 nF 50 50 10 10 2 3 4 5 6 2 3 4 5 6 10 10 10 10 Hz 10 10 10 10 10 Hz 10 f f 125 12/00 MKP B32 621 10 Permissible ac voltage V versus frequency f rms Lead spacing 10 mm 160 Vdc / 90 Vac 250 Vdc / 140 Vac KMK0715-4 KMK0716-C 400 400 Vac Vac 200 200 V V rms rms 100 100 60 60 40 40 folgt fol 20 20 47 nF 2,2 nF 0,10 µF 15 nF 10 10 0,22 µF 0,10 µF 6 6 4 4 2 2 1 1 2 3 4 5 6 2 3 4 5 6 10 10 10 10 Hz 10 10 10 10 10 Hz 10 f f 400 Vdc / 200 Vac 630 Vdc / 400 Vac KMK0703-F KMK0552-V 1000 1000 V ac V ac V rms V rms 500 500 100 100 2,2 nF 15 nF 10 nF 50 33 nF 50 47 nF 10 10 2 3 4 5 6 2 3 4 5 6 10 10 10 10 Hz 10 10 10 10 10 Hz 10 f f 126 12/00 B32 621 MKP 10 Permissible ac voltage V versus frequency f rms Lead spacing 10 mm 1000 Vdc / 500 Vac KMK0551-M 1000 Vac V ac V rms 500 100 2,2 nF 50 10 nF 10 2 3 4 5 6 10 10 10 10 Hz 10 f 127 12/00 MKP B 32 620 B 32 621 Sinus-wave application, lighting Permissible voltage and current / waveform V pp V 0-p t = 10 ... 63,5 µs I pp KMK0721-D 128 12/00 B32 620 MKP 7,5 Sinus-wave application, lighting Permissible current I versus rated capacaitance C pp R Lead spacing 7,5 mm 160 Vdc/90 Vac 250 Vdc/140 Vac KMK0681-F KMK0640-D 1,6 0,4 A pp A pp 100 kHz 1,4 I I pp pp 100 kHz 0,3 1,2 1,0 0,25 50 kHz 50 kHz 0,2 0,8 0,15 0,6 0,4 0,1 0,05 0,2 0 0 050 100 nF 150 020 40 60 nF 80 C C 400 Vdc/200 Vac 630 Vdc/400 Vac KMK0641-L KMK0642-U 0,8 0,6 A pp A pp 0,7 I I pp pp 0,5 100 kHz 0,6 100 kHz 0,4 0,5 50 kHz 0,4 0,3 50 kHz 0,3 0,2 0,2 0,1 0,1 0 0 010 20 30 nF 40 0 510 15 nF 20 C C 129 12/00 MKP B32 620 B32 621 7,5 10 Sinus-wave application, lighting Permissible current I versus rated capacaitance C pp R Lead spacing 7,5 mm 1000 Vdc/500 Vac 1000 Vdc/600 Vac KMK0643-3 KMK0644-B 0,3 0,4 A A pp pp I I pp pp 100 kHz 100 kHz 0,3 0,2 0,25 50 kHz 50 kHz 0,15 0,2 0,15 0,1 0,1 0,05 0,05 0 0 12 3 4 nF 5 12 3 4 nF 5 C C Lead spacing 10 mm 160 Vdc/90 Vac 250 Vdc/140 Vac KMK0653-A KMK0654-I 0,8 0,6 A pp A pp 100 kHz 0,7 I I pp pp 0,5 100 kHz 0,6 50 kHz 0,4 0,5 50 kHz 0,4 0,3 0,3 0,2 0,2 0,1 0,1 0 0 0 50 100 150 200 nF 250 0 50 100 nF 150 C C 130 12/00 B32 621 MKP 10 Sinus-wave application, lighting Permissible current I versus rated capacaitance C pp R Lead spacing 10 mm 400 Vdc/200 Vac 630 Vdc/400 Vac KMK0645-J KMK0655-F 0,4 1,4 A pp A pp I I pp pp 1,2 100 kHz 0,3 1,0 100 kHz 50 kHz 0,8 0,2 0,6 50 kHz 0,4 0,1 0,2 0 0 0 10 20 30 40 nF 50 0 10 20 nF 30 C C 1000 Vdc/500 Vac KMK0646-S 0,6 A pp 100 kHz I pp 0,5 50 kHz 0,4 0,3 0,2 0,1 0 0 2 46 8 10 nF 12 C 131 12/00 Herausgegeben von EPCOS AG Marketing Kommunikation, Postfach 80 17 09, 81617 München, DEUTSCHLAND  EPCOS AG 2000. Alle Rechte vorbehalten. Vervielfältigung, Veröffentlichung, Verbreitung und Verwertung dieser Broschüre und ihres Inhalts ohne ausdrückliche Genehmigung der EPCOS AG nicht gestattet. Mit den Angaben in dieser Broschüre werden die Bauelemente spezifiziert, keine Eigenschaften zugesichert. Bestellungen unterliegen den vom ZVEI empfohlenen Allgemeinen Lieferbedingungen für Erzeugnisse und Leistungen der Elektroindustrie, soweit nichts anderes vereinbart wird. Diese Broschüre ersetzt die vorige Ausgabe. Fragen über Technik, Preise und Liefermöglichkeiten richten Sie bitte an den Ihnen nächstgele- genen Vertrieb der EPCOS AG oder an unsere Vertriebsgesellschaften im Ausland. Bauelemente können aufgrund technischer Erfordernisse Gefahrstoffe enthalten. Auskünfte darüber bitten wir unter Angabe des betreffenden Typs ebenfalls über die zuständige Vertriebsge- sellschaft einzuholen. Published by EPCOS AG Marketing Communications, P.O. Box 80 17 09, 81617 Munich, GERMANY  EPCOS AG 2000. All Rights Reserved. Reproduction, publication and dissemination of this bro- chure and the information contained therein without EPCOS’ prior express consent is prohibited. The information contained in this brochure describes the type of component and shall not be con- sidered as guaranteed characteristics. Purchase orders are subject to the General Conditions for the Supply of Products and Services of the Electrical and Electronics Industry recommended by the ZVEI (German Electrical and Electronic Manufacturers’ Association), unless otherwise agreed. This brochure replaces the previous edition. For questions on technology, prices and delivery please contact the Sales Offices of EPCOS AG or the international Representatives. Due to technical requirements components may contain dangerous substances. For information on the type in question please also contact one of our Sales Offices. 1