ELECTRONIC SIGNALS ® Adaptatone Millennium Central Tone Generator Synchronized System Signaling, Four Outputs, RS485 Activation 5540M Series FEATURES > 27 tone capability - No additional The Edwards 5540M Millennium Central Tone Generator has been tone modules needed designed for applications where simultaneous signaling of a high > PLC Compatible decibel, heavy duty signal is required. The tone generator assures a > Captive Components synchronous signaling sound from all remote speakers. The Millen- nium Central Tone Generator produces the 27 standard Adaptatone > Centralized programmable tone sounds. Four tones may be activated from field-wired, normally selection open contacts, or a 24VDC or 120VAC external voltage source > System-wide priority tone such as an output of a PLC. selection > RS485 models available Normally open contacts can be obtained from the Cat. No. 5538-4 or Cat. No. 5538-4R Adaptatone Signal Actuator. See page 4-49. The AGENCY APPROVALS tones are selected by setting miniature dip switches within the unit. > NEMA Type 3R The programmed tones operate on a pyramid-type priority system. > IP 44 For more information on priority tone operation and a complete list- ing of all 27 tones, see page 4-55. > UL 464 and 1604 Listed > UL Listed for indoor and outdoor On-site volume control is accomplished by adjusting the conve- applications in Class I, Div. 2, niently located volume control inside the unit. Groups A, B, C & D; Class II, Div. 2, Groups F & G; and Class III The 5540M-485Y6 is designed to be connected to RS485 networks, hazardous locations allowing full serial signaling communication control. > cUL C22.2 No. 205 (24AQ, 24N5 Adaptatone Signaling Systems are designed for industrial applica- & 24Y6 models) tions calling for high decibel output and microprocessor reliability > TUV Rheinland Certified combined with simultaneous signal delivery over all speakers in- > CE Marked - Cenelec LV & EMC cluded in the system. Typical applications include: emergency Directives (24Y6 AC only & warning systems, plant evacuation alarms, security intrusion si- 24AQ models) rens, process monitoring, shift start-and-dismissal horns, and pag- ing signals. SPECIFICATIONS > 24V DC battery backup terminals RS485 units are MEDI compatible. See page 4-10. > Short Circuit protected || 90 Fieldstone Court ||| Cheshire, CT 06410 © Copyright 2004 Edwards Ph: 203.699.3300 ||||| Fx: 203.699.3108 www.edwards-signals.com D-04 4-28 D-04 4-29 ELECTRONIC SIGNALS TECHNICAL INFORMATION Mounting flange 8" 4 holes (2 each side) (203mm) 2 1/2" 6" 4" (152mm) (64mm) (102mm) 6" 1/2" (13mm) (152mm) 3 1/2" conduit mounting (89mm) Operating Input Card Signal Off Signal On Cat. No. Voltage Activation Voltage Standby Current (Amps) Operating Current (Amps) 5540M-24AQ 24V DC 24VDC 0.10 0.74 24V AC 50/60 Hz 0.10 1.3 5540M-24N5 120V AC 50/60 Hz 24VDC 0.10 0.36 5540M-120N5 120V AC 50/60 Hz 120VAC 0.10 0.38 5540M-24Y6 120V AC 50/60 Hz 24V DC 0.10 0.32 240V AC 50/60 Hz 0.10 0.20 125V DC 0.10 0.21 250V DC 0.02 0.10 5540M-120Y6 120V AC 50/60 Hz 120VAC 0.10 0.31 240V AC 50/60 Hz 0.10 0.20 125V DC 0.10 0.20 250V DC 0.02 0.10 5540M-485Y6 120V AC 50/60 Hz RS485 0.10 0.31 240V AC 50/60 Hz 0.10 0.20 125V DC 0.10 0.20 250V DC 0.02 0.10 SIGNAL INPUT LOAD CHARACTERISTICS* (PLC output to meet following product input parameters) Operating Max. off state Continuous on Surge (inrush/duration) Cat. No. voltage leakage current (mA) current (mA) Amps/milliseconds 5540M-24AQ 24V DC only 2 740 8/4 5540M-24N5 120V 60 Hz 2 360 2.82/4 5540M-120N5 120V 60 Hz 5 380 2.82/4 5540M-24Y6 120V 60 Hz 2 320 2.82/4 5540M-120Y6 120V 60 Hz 5 310 2.82/4 24VDC Input Board 24V DC (each input) 26 — 120VAC Input Board 120VAC 60 Hz (each input)513 — *This device is PLC compatible and may be operated by PLCs with output characteristics that match the input load requirements of this signal. || 90 Fieldstone Court ||| Cheshire, CT 06410 © Copyright 2004 Edwards Ph: 203.699.3300 ||||| Fx: 203.699.3108 www.edwards-signals.com