Manufacturers
E-T-A CIRCUIT PROTECTION AND CONTROL 2-5700-IG1-K10-DD-5A
Description
Circuit Breaker; 5 A; 250 VAC/28 VDC; 3000; 100 Megohms (Min.); 0.35 in.; Screw
Part Number
2-5700-IG1-K10-DD-5A
Price
Request Quote
Manufacturer
E-T-A CIRCUIT PROTECTION AND CONTROL
Lead Time
Request Quote
Category
PRODUCTS - 2
Datasheet
Extracted Text
Thermal Overcurrent Circuit Breakers 2-5000/2-5700-... Description Single pole thermal circuit breaker with press-to-reset, tease-free, trip- free, snap action mechanism. Type 2-5000 is available with optional manual release (-H), type 2-5700 can be supplied as a push-push switch/circuit breaker (R-type TO CBE to EN 60934 in press-to-reset configuration; M-type when fitted with manual release -H; S-type with push-push operation). Fitted with flange or threadneck for panel mounting. Options include an additional unprotected circuit tap (-A3). Approved to CBE standard EN 60934 (IEC 60934). 1 Typical applications Motors, transformers, solenoids, battery chargers, power supplies, appliances, machinery, extra low voltage systems. 2-5000-... 2-5700-... Ordering information Technical data Type No. Voltage rating AC 250 V; DC 28 V (UL: DC 50 V) 2-5000 flange mounting Current rating range 0.05...25 A 2-5700 threadneck panel mounting (hardware bulk shipped) Threadneck design – type 2-5700 only Typical life 5,000 operations at 2 x I N iG1 moulded threadneck 3/8"-27UNS-2A Ambient temperature -20...+60 °C (-4...+140 °F) iG2 moulded threadneck M12x1 Insulation co-ordination Rated impulse Pollution Terminal design (IEC 60664 and 60664 A) withstand voltage degree P10 blade terminals 6.3-0.8 mm (QC .250) 2.5 kV 2 K10 screw terminals M4x6 reinforced insulation in operating area Shunt terminal (optional) -P10 only A3 shunt terminal (up to I 2.5 A/6 A max. load) Dielectric strength N Manual release (optional) (IEC 60664 and 60664A) Test voltage H manual release facility (type 2-5000 only) operating area AC 3,000 V DD push to release/push to reset (type 2-5700 only) Insulation resistance > 100 MΩ (DC 500 V) Current ratings Interrupting capacity I 0.05...2.5 A 8 x I cn N 0.05 ... 25 A 3... 5 A 20 x I N 6...12 A 200 A (higher interrupting 2-5700 - iG1 - P10 - - DD - 8 A ordering example capacity available to special order) 13...25 A 400 A The exact part number required can be built up from the table of choices shown above. Ordering references for optional features should be omitted if not required. Interrupting capacity I U N N (UL 1077) 0.05...20 A AC 250 V 2,000 A 0.05...25 A DC 50 V 2,000 A Degree of protection operating area IP 40 (IEC 60529/DIN 40050) terminal area IP 00 Vibration 8 g (57-500 Hz) ±0.61 mm (10-57 Hz), to IEC 60068-2-6, Test Fc, Standard current ratings and typical internal resistance values 10 frequency cycles/axis Shock 25 g (11 ms) Current Internal Current Internal to IEC 60068-2-27, test Ea rating (A) resistance (Ω) rating (A) resistance (Ω) Corrosion 96 hours at 5 % salt mist, 0.05 280 3 0.1 to IEC 60068-2-11, test Ka 0.08 100 3.5 0.065 Humidity 240 hours at 95 % RH to IEC 60068-2-3, test Ca 0.1 110 4 0.065 0.2 29 4.5 0.05 Mass approx. 29 g 0.3 14 5 0.05 0.4 7 6 0.02 0.5 4.9 7 0.02 Approvals 0.6 3.4 8 < 0.02 0.7 2.5 10 < 0.02 Authority Voltage ratings Current ratings 0.8 1.8 12 < 0.02 VDE (EN 60934) AC 250 V; DC 28 V 0.05...25 A 1 1.2 13 < 0.02 CSA/ UL AC 250 V; DC 50 V 0.05...20 A 1.2 0.85 15 < 0.02 CSA/UL DC 50 V 0.05...25 A 1.5 0.6 16 < 0.02 Semko (EN 60934) AC 250 V; DC 28 V 0,05...25 A 1.8 0.4 20 < 0.02 SEV AC 250 V; DC 28 V 0,05...25 A 2 0.3 22 < 0.02 LRoS (type 2-5700 only) AC 250 V; DC 28 V 0.1 ...25 A 2.5 0.2 25 < 0.02 BV (type 2-5700 only) AC 250 V; DC 28 V 0.2 ...25 A Issue D USA (847) 827-7600 - www.e-t-a.com - CANADA (905) 764-9510 99 Thermal Overcurrent Circuit Breakers 2-5000/2-5700-... Dimensions Terminal design 2-5000-P10 -P10-A3 -K10 0.05...2.5 A ş9.5 ş13.5 .374 .531 14 32 14 32 1 13 .512 flat head screw M4x6 ISO1580 tightening torque 1.2 Nm A 14 32 Installation drawings 19.8 14.5 .780 .571 31 blade terminal DIN 46244-A6.3-0.8 2-5000-... 1.22 (QC .250) current rating in A operating area 2-5000-P10-A3 0.05...2.5 A 5 14 32 40 1.57 13 50 .512 1.97 A 2-5700-P10 14 32 3 iG1= / -27UNS-2A tightening torque max. 1 Nm 8 mounting area iG2=M12x1 tightening torque max. 1.5 Nm ş6.5 .256 2-5700-... A operating area A 14 32 blade terminal DIN 46244-A6.3-0.8 14.5 19.8 (QC .250) .571 .780 29 14 32 1.14 D-shaped threadneck current rating in A for standard mounting area 1 1 (-DD version without push button marking) .039 .039 mounting hole 5 SW 14 .551 iG1=ş9.6 -0.1 iG2=ş12.2 -0.1 iG1=.378 -.004 iG2=.480 -.004 mm This is a metric design and millimeter dimensions take precedence ( ) inch 100 USA (847) 827-7600 - www.e-t-a.com - CANADA (905) 764-9510 Issue D iG1=8.8 OFF 22.5 iG2=11.3 5 iG1=.346 .886 .197 iG2=.445 16.5 ON .650 46.5 10 10.4 .409 1.83 .394 ş4.5 10.4 12.2 ON .177 .480 .409 18.5 44 18.2 OFF .728 1.73 .717 7 .276 iG1=8.9 -0.1 iG2=11.5 -0.1 iG1=.350 -.004 iG2=. 453 -.004 25 .984 10.4 .409 25 .984 max. 2.5 max. 2.5 max .098 max .098 Thermal Overcurrent Circuit Breakers 2-5000/2-5700-... Internal connection diagrams 0.05...2.5 A 3...25 A (with or without shunt terminal) (without shunt terminal) 1 1 (3) 1 (-A3) 2 2 Typical time/current characteristics at +23°C/+73.4°F 10000 0.05 - 2.5 A 3 - 25 A 1000 100 10 1 0.1 12 46810 20 40 … times rated current The time/current characteristic curve depends on the ambient temperature prevailing. In order to eliminate nuisance tripping, please multiply the circuit breaker current ratings by the derating factor shown below. See also section 9 – Technical information. Ambient temperature °F -4 +14 +32 +73.4 +104 +122 +140 °C -20 -10 0 +23 +40 +50 +60 Multiplication factor 0.76 0.84 0.92 1 1.08 1.16 1.24 Issue D USA (847) 827-7600 - www.e-t-a.com - CANADA (905) 764-9510 101 Trip time in seconds Thermal Overcurrent Circuit Breakers 2-5000/2-5700-... Accessories for types 2-5000 and 2-5700 with screw terminals -K10 176 Bus bar 6.93 Y 303 563 01 162 X 6.38 7 18 60° .276 .709 1 X Accessories for type 2-5000-... Accessories for type 2-5700-... Water splash cover, transparent Fixing plate With 3/8" threadneck (-iG1) for push button (IP64) Y 301 056 02 Water splash cover, transparent with knurled nut X 200 799 01 (IP64) Y 300 728 01 50 31.5 14.5 1.97 1.24 .571 40 4.5 18 1.57 .177 .709 3 / -27 UNS-2B 8 Hex nut with splash cover black Water splash cover, transparent X 210 739 01 (IP64) 40 with special knurled nut transparent splash cover 1.57 X 200 798 02 (IP64) X 201 296 03 (IP64) 50 1.97 Rear terminal shroud, transparent (IP64) Y 300 476 01 3 / -27 UNS-2B 3 8 / -27 UNS-2B 8 12.5 29 .492 1.14 Separate hardware Hex nut Knurled nut Y 300 192 01 Y 300 284 02 E - T - A 3/8-27UNS-2B 3/8-27UNS-2B 2.5 SW14 SW14 4 ş12 ş6 .551 .098 .157 .472 .236 With M12 threadneck (-iG2) Hex nut with splash cover, black Water splash cover, X 201 296 01 without O ring (IP64) transparent, X 200 801 03 with O ring (IP66) with knurled nut Hex nut with splash cover, X 210 663 01 (IP64) transparent X 200 801 08 with O ring (IP66) M12x1 M12x1 Separate hardware Hex nut Knurled nut Y 300 116 02 Y 302 065 01 M12x1 3.2 M12x1 .126 mm This is a metric design and millimeter dimensions take precedence ( ) inch All dimensions without tolerances are for reference only. In the interest of improved design, SW14 2.5 0.5 x 45° ş17 performance and cost effectiveness the right to make changes in these specifications without .098 .551 .020 x 45° .669 notice is reserved.Product markings may not be exactly as the ordering codes. Errors and omissions excepted. 102 USA (847) 827-7600 - www.e-t-a.com - CANADA (905) 764-9510 Issue D 1.5 .059 10 .394 49 M4 1.93 .756 18.5 2.3 .728 .091 0.5 .020 2 .079 1.1 .043 ş13.5 .531 ş11.4 .449 19.2
Frequently asked questions
What makes Elite.Parts unique?
What kind of warranty will the 2-5700-IG1-K10-DD-5A have?
Which carriers does Elite.Parts work with?
Will Elite.Parts sell to me even though I live outside the USA?
I have a preferred payment method. Will Elite.Parts accept it?
What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods