™ ™ Mini-Mux 210 & Mini-Mux 280 Drop T1/E1 lines from T3/STS-1 feeds using the versatile Mini-Mux single rack unit shelf. Charles Industries’ Mini-Mux 210 (E1 version) 1:1 redundancy is provided on both the high- and 280 (T1 version) are industry leading M13 speed and drop ports for added reliability. multiplexer solutions. The Mini-Mux 210 Integrated T1/E1 testing makes fault isolation multiplexes E1s into a T3, STS-1, or AU3 routine, and unlike most M13 muxes, T1/E1 signal. Likewise, the Mini-Mux 280 multiplexes framing information is included to provide T1s into a T3 or STS-1. Both units feature low additional performance statistics. power consumption and a small 1 rack unit footprint ideal for co-location applications. Features  M13 Multiplexers optimized for smaller  19”, 1 RU shelf, flush or offset mounting deployments  Sophisticated T1/E1 testing with internal  Field configurable for T3, or STS-1operation pattern generator and receiver (Mini-Mux 210 is also AU3 configurable)  Integral T1/E1 frame monitoring  Low power consumption: 17 Watts  Terminal, Telnet, SNMP, TL-1, and Web  Convection cooled, no fans required management interfaces Applications  T1/E1 dropoff from a SONET/SDH network  Consolidating T1s/E1s in wireless networks  Provisioning Hi-Cap T1 services  Transporting E1s over T3/STS-1  Backhauling T1/E1 traffic between central offices Specifications T3 INTERFACE PERFORMANCE MONITORING Line Rate: 44.736 Mbps +/- 20ppm Cumulative Errored Seconds: Line Format: Bipolar B3ZS encoded  T1/E1 BPV Framing: C-Bit Parity or M13  T1/E1 Frame Bit or CRC errors Line Build-Out: 0-900 feet of cable  STS-1 Section (B1) errors Input Level: 35mV to 900mV  STS-1 Line (B2) errors Clocking: Loop or Internal Timed  T3 P-bit errors  T3 CP-bit errors STS-1/AU3 INTERFACE  T3 FEBE errors Line Rate: 51.84 Mbps +/- 20ppm  VT1.5/VT2/TU-12 parity errors Line Format: Bipolar B3ZS encoded Line Build-Out: 0-900 feet of cable POWER Input Level: 35mV to 900mV  Separate A & B battery feeds Clocking: Loop or Internal Timed  -48VDC or +24VDC, 17 watts maximum E1 INTERFACE (Mini-Mux 210 only) TIMING Line Rate: 2.048 Mbps +/- 50ppm  T3 loop-timed or internally timed Line Code: AMI or HDB3  STS-1 loop-timed or internally timed Line Framing: CCS, CAS, Unframed TESTABILITY T1 INTERFACE (Mini-Mux 280 only)  T3 and STS-1 Line Loopback Line Rate: TX: 1.544 Mbps +/- 50 ppm  T1/E1 Loopbacks (toward T1/E1 drop and/or RX: 1.544 Mbps +/- 130 ppm T3/STS-1 line) Line Code: AMI or B8ZS  Remote C-bit loopback (for T3) Line Build-Out: 0 to 655 ft.  Manual and Automatic Protection switching for Line Framing: SF (D4), ESF, or Unframed high and low speed ports  T1/E1 Test Patterns (Gen & Rec) MECHANICAL SYSTEM MANAGEMENT 19” Shelf: 1.75” (4.45 cm.) high,  VT100 terminal compatibility 17.37” (44.12 cm.) wide,  Telnet 10.03” (25.49 cm.) deep  SNMP (Fully-compliant Charles Industries MIB) Weight: Maximum of 10 lbs.  Web interface (fully loaded and redundant)  TL-1 interface ENVIRONMENTAL  Serial interface, 1200 baud to 115 kilobaud  Ambient operating temperature from -40º to  Ethernet 10BaseT, RJ45 Connector +65º C CERTIFICATIONS  Relative humidity to 95% (non-condensing)  UL/C-UL  Altitude to 12,000 ft. (3660 m)  CE Mark (Mini-Mux 210 only) ALARMS  NEBS Level 3  External contacts for visual and audible alarms  FCC Part 15 Class A  Major and Minor Alarms  Normally open and normally closed pin-out  Front panel alarm cutoff switch With Charles, You Can Depend On:  Field-proven and unequaled 24-hour technical support  Individualized application consultation  Training courses available Visit our website at http://www.charlesindustries.com Charles Industries, Ltd. Voice: (847) 806-6300 Telecommunications Group FAX: (847) 806-6231 5600 Apollo Drive E-mail: mktserv@charlesindustries.com Rolling Meadows, IL 60008 is a registered trademark of Charles Industries, Ltd. D-AAT108-G04