C&K BD Series Standard Profile DIP Switches Features/Benefits Typical Applications • Traditional full profile DIP • Address switch for industrial switch controls H • Extended actuator for easy • Logic switching for computers actuation and peripherals • Open bottom construction • Function controlling for allows for solder washing numerous applications without the need for tape seal How To Order Complete part numbers for BD Series are shown on pages H-9 thru H-10. All switches supplied in “OFF” position. VIBRATION: No contact opening greater than 10 microseconds and no Specifications contact closure when exposed to vibration .06 in DA or 5g, whichever is less, from 10 to 55 Hz, and 10g from 55 to 500 Hz. SWITCH FUNCTION: SPST - 1 thru 12 position available SOLDERABILITY: Per MIL-STD-202F method 208D, or EIA RS-186E (except 11 position). method 9 (1 hour steam aging). CONTACT RATING: PACKAGING: Switches supplied in rigid dispensing tubes in full-tube Carry: 100 mA max. @ 50 V DC. quantities only: this may effect order quantity. Number of switches Switch: 100 mA max. @ 5 V DC or 25 mA max. @ 25 V DC. per tube varies with model. Switch position 1 denotes pin number MECHANICAL AND ELECTRICAL LIFE: 10,000 make-and-break 1. All switch actuators in ‘OFF’ position, standard. cycles at full load, each circuit. CONTACT RESISTANCE: Below 50 milliohms typ. initial Materials @ 2-4 V DC 100mA. CASE & COVER: Glass filled polyester (PBT), 9 INSULATION RESISTANCE: 10 ohms min. flame retardant (UL 94V-0). DIELECTRIC STRENGTH: 500 V RMS min. @ sea level between ACTUATOR: Glass filled nylon 6/6, flame retardant, adjacent terminals. heat stabilized (UL 94V-0) CAPACITANCE: 5pF max. between adjacent terminals. CONTACTS: WE#1 over palladium silver over nickel or gold over nickel STORAGE & OPERATING TEMPERATURE: -40°C to 85°C. over phosphor bronze. SHOCK: Withstands 20g 11 ms sawtooth waveform with no con- NOTE: Specifications and materials listed above are for switches with standard options. For tact opening greater than 10 microseconds. information on specific and custom switches, consult Customer Service Center. QUANTITY Vertical Full Profile DIP PART NUMBER NO.POS. DIM. ‘A’ PER TUBE BD01 1 .180 (4,57) 115 .072 Ş.038 TYP. (0,97) BD02 2 .280 (7,11) 74 (1,83) .100 TYP. ACTUATOR BD03 3 .380 (9,65) 54 DIM 'A' (2,54) TRAVEL BD04 4 .480 (12,19) 43 O N BD05 5 .580 (14,73) 35 .380 .300 (9,65) (7,62) BD06 6 .680 (17,27) 30 2345678 1 BD07 7 .780 (19,81) 26 BD08 8 .880 (22,35) 23 .160 TYP. DIM 'B' BD08 (4,06) BD09 9 .980 (24,89) 21 .060 TYP. (1,52) .080 TYP. BD10 10 1.080 (27,43) 19 (2,03) BD12 12 1.280 (32,51) 16 .305 .040 Schematic .026 (7,75) (1,02) (0,66) TYP. SPST .007 .090 .020 TYP. .100 TYP. (0,18) (2,29) .300 (0,51) (2,54) (7,62) .141 TYP. (3,58) Third Angle Projection Dimensions are shown in inch (mm ) Dimensions subject to change www.ittcannon.com H-10 DIP DIP C&K BD Series Standard Profile DIP Switches Open Base and AV Right Angle Terminal Style 0.050 .090 (1,27) (2,29) QUANTITY PART NUMBER NO.POS. DIM. ‘A’ PER TUBE 0.026 (0,66) H BD02AV 2 .280 (7,11) 72 0.300 BD03AV 3 .380 (9,65) 52 BD08AV (7,62) BD04AV 4 .480 (12,19) 42 BD05AV 5 .580 (14,73) 35 0.061 TYP. (1,55) BD06AV 6 .680 (17,27) 29 DIM.A BD07AV 7 .780 (19,81) 26 BD08AV 8 .880 (22,35) 23 ON BD09AV 9 .980 (24,89) 20 .380 (9,65) BD10AV 10 1.080 (27,43) 18 .125 1 2 3 4 5 6 7 8 BD12AV 12 1.280 (32,51) 15 (3,18) Schematic .020 TYP. .010 .100 TYP. (0,51) .007 (0,25) (2,54) (0,18) .100 .320 .100 SPST (2,54) (8,13) (2,54) NOTE: Box dimensions show difference between AV and AV2 terminal styles. .100 TYP. .046 DIA TYP. (2,54) (1,17ş) Open Base and AV2 Right Angle Terminal Style 0.050 .090 (1,27) (2,29) QUANTITY 0.026 PART NUMBER NO.POS. DIM. ‘A’ PER TUBE (0,66) BD02AV2 2 .280 (7,11) 72 0.300 BD08AV2 BD03AV2 3 .380 (9,65) 52 (7,62) BD04AV2 4 .480 (12,19) 42 0.061 TYP. BD05AV2 5 .580 (14,73) 35 (1,55) BD06AV2 6 .680 (17,27) 29 DIM.A BD07AV2 7 .780 (19,81) 26 ON BD08AV2 8 .880 (22,35) 23 .380 BD09AV2 9 .980 (24,89) 20 (9,65) BD10AV2 10 1.080 (27,43) 18 .115 1 2 3 4 5 6 7 8 (2,92) BD12AV2 12 1.280 (32,51) 15 Schematic .010 .020 TYP. .007 (0,51) .100 TYP. (0,25) (0,18) (2,54) .280 .100 0.100 (7,11) (2,54) (2,54) SPST NOTE: Box dimensions show difference between AV and AV2 terminal styles. 0.100 TYP. 0.046 DIA TYP. (2,54) (1,17ş) Installation, Soldering and Cleaning All BD Series Standard Profile DIP Switches can be hand soldered or machine soldered without the use of boot, caps, tapes or special attention. Open base washable models have unique design, allowing solvent cleaners and water/detergent solutions to flush and clean the electrical contacts of the contaminants and fluxes. For best results, follow these directions: 1.) Wave soldering recommended at 500° F solder temperature. 2.) Hand solder using 30 watt small tip iron controlled at 500° F, 10 seconds max./terminal. 3.) Open base washable models: Clean flux using forced rinse, high agitation or triple bath cleaning method. DO NOT mask or cover switch in any way during cleaning. Switch is designed for easy solvent flush out. 4.) All switch actuators must be in ‘OFF’ position during soldering and cleaning processes. 5.) Closed base models with epoxy terminal seal available in even positions, consult factory for details. Dimensions are shown inch (mm) Dimensions subject to change www.ittcannon.com H-11