8060 Series Alternate Action and Momentary Pushbutton Switches Features/Benefits Typical Applications A • Long travel • Instrumentation • Available with LED • Computers and peripherals • Long life contact design • Telecommunications and networking equipment • Epoxy terminial seal compatabile with bottom wash cleaning • RoHS compliant models available Models Available Specifications Materials CONTACT RATING: Q contact material: 6 AMPS @ 120 V AC CASE: Glass filled nylon 6/6 or diallyl phthalate (DAP), or 28 V DC; 3 AMPS @ 250 V AC. See page A-59 for flame retardant (UL 94V-0). additional ratings. PLUNGER: S, S1, S2 Options: Glass filled nylon or glass filled ELECTRICAL LIFE: 50,000 make-and-break cycles at full load. polyester (PBT) (UL 94V-0). L, L1 Options: Brass, nickel plated. CONTACT RESISTANCE: Below 20 mΩ typ. initial @ CAP & FRAME: Nylon, black standard. 2-4 V DC, 100 mA, for both silver and gold plated contacts. BUSHING: Brass or zinc, nickel plated. 9 INSULATION RESISTANCE: 10 Ω min. HOUSING: Stainless steel. DIELECTRIC STRENGTH: 1,000 Vrms min. @ sea level. SWITCH SUPPORT: Brass or steel, matte-tin plated. OPERATING TEMPERATURE: –30ºC to 65ºC END CONTACTS: Q contact material: Coin silver, silver plated. SOLDERABILITY: Per MIL-STD-202F method 208D, or See page A-59 for additional contact materials. EIA RS-186E method 9 (1 hour steam aging). CENTER CONTACT & ALL TERMINALS: Q contact material: Copper CAP INSTALLATION FORCE: 10 lbs. maximum permissible. alloy, silver plated. See page A-59 for additional contact materials. TERMINAL SEAL: Epoxy. Refer to soldering and cleaning NOTE: Any models supplied with P, R, S, Q, B or G contact material are RoHS compliant. in Technical Data Chapter. HARDWARE: Nut & Locking Ring: Brass, nickel plated; NOTE: Specifications and materials listed above are for switches with standard options. For information on specific and custom switches, consult Customer Service Center. Lockwasher: Steel, nickel plated. Build-A-Switch To order, simply select desired option from each category and place in the appropriate box. Available options are shown and described on pages A-53 thru A-61. For additional options not shown in catalog, consult Customer Service Center. All models have epoxy terminal seal and are compatible with all “bottom-wash” PCB cleaning methods. Switch Function Bushing 8161 SPDT On-On H .300" high, flat, hi torque Contact Material 8168 SPDT On-Mom. H9 .300" high, flat, hi torque B Gold 8261 DPDT On-On NONE No bushing choice required P Gold, matte-tin Y3 7.6mm, keyway Q Silver Actuator or Plunger S Silver, matte-tin S .710" high plunger Terminations G Gold over silver with .375" dia. cap A Right angle, PC thru-hole R Gold over silver, J80 Snap-in AV2 Vertical right angle, matte-tin J81 Snap-in with frame PC thru-hole J82 Snap-in with frame for LED C PC Thru-hole Seal J86 Snap-in with frame & LED Z Solder lug E Epoxy L .740" high plunger with A3 Right angle, snap-in, PC thru-hole .395" dia. cap AV3 Vertical right angle, snap-in, I Epoxy potted base L1 .740" high plunger with PC thru-hole .590" dia. cap V3 .460" high, V-bracket Cap Color S1 .615" high plunger with V4 .630" high, V-bracket 2 Black .200" dia. cap V6 .460" high, V-bracket 1 White S2 .710" high plunger with V21 .555" high, snap-in V-bracket 3 Red .310" dia. cap V31 .460" high, snap-in V-bracket Frame Color 4 Orange W .750" long, wire wrap 2 Black 5 Yellow Z3 Quick connect 9 Gray LED Color 3 Red NONE Models without LED Dimensions are shown: Inches (mm) Specifications and dimensions subject to change www.ck-components.com A-52 Pushbutton Pushbutton 8060 Series Alternate Action and Momentary Pushbutton Switches SWITCH FUNCTION A SWITCH FUNCTION CONNECTED TERMINALS POS. 1 POS. 2 POS. 1 POS. 2 NO. C&K marking this side C&K marking this side POLES MODEL NO. SCHEMATIC 8161 ON ON 2-3 2-1 SP 8168 ON MOM. 2-3 2-1 SPDT SPDT Terminal Nos. Part number shown: 8161SHZQE For Reference Only DP 8261 ON ON 2-3,5-6 2-1,5-4 DPDT DPDT Terminal Nos. Part number shown: 8261SHZQE For Reference Only MOM. = Momentary All models with all options when ordered with G or Q contact material. CAP COLOR ACTUATOR—SNAP-IN FRONT MOUNT ACTUATOR OR PLUNGER J80 SNAP-IN PANEL MOUNTING * OPTION CODE CAP COLOR 2 BLACK 1 WHITE 3 RED *Increase this dimension to 4 ORANGE .620/.625 (15,75/15,88) for .091/.125 (2,41/2,18) 5 YELLOW thick panels. 9 GRAY J81 SNAP-IN WITH BLACK FRAME P PANEL MOUNTING ANEL MOUNTING Cap Finish: matte. Other colors available, consult Customer Service Center. Available with C, W, Z or Z3 terminations. NOTE: Caps & frames available separately, see pages A-60 and A-61. * * *Increase this dimension to .620/.625 (15,75/15,88) for .091/.125 (2,41/2,18) Third Angle thick panels. Projection Dimensions are shown: Inches (mm) Specifications and dimensions subject to change www.ck-components.com A-53 8060 Series Alternate Action and Momentary Pushbutton Switches CAP COLOR ACTUATOR—SNAP-IN FRONT MOUNT ACTUATOR OR PLUNGER A J82 SNAP-IN WITH BLACK FRAME FOR LED Available with C, W, Z or Z3 terminations. OPTION LED not included. CODE CAP COLOR For LED information, see page A-61. 2 BLACK NOTE: Caps & frames available separately, see pages A-60 and A-61. 1 WHITE Other colors available, consult 3 RED Customer Service Center. 4 ORANGE 5 YELLOW 9 GRAY CAP COLOR LED COLOR ACTUATOR—SNAP-IN FRONT MOUNT ACTUATOR OR PLUNGER J86 SNAP-IN WITH BLACK FRAME AND LED PANEL MOUNTING * * Increase this dimension to 8161J86ZQE223 .620/.625 (15,75/15,88) SPDT for .091/.125 (2,31/3,18) thick panels. Available with C, W, Z or Z3 terminations and SPDT models only. OPTION OPTION NOTE: Caps & frames available CODE CAP COLOR CODE LED COLOR separately, see pages A-60 and A-61. 2 BLACK 3 RED Other colors available, consult 1 WHITE For LED information, see page A-61. Customer Service Center. 3 RED 4 ORANGE 5 YELLOW 9 GRAY Third Angle Projection Dimensions are shown: Inches (mm) Specifications and dimensions subject to change www.ck-components.com A-54 Pushbutton Pushbutton 8060 Series Alternate Action and Momentary Pushbutton Switches CAP COLOR PLUNGER ACTUATOR OR PLUNGER A S PLUNGER WITH CAP P/N 7527 S1 PLUNGER WITH CAP P/N 7089 S2 PLUNGER WITH CAP P/N 8018 L PLUNGER WITH CAP P/N 8941 L1 PLUNGER WITH CAP P/N 8940 OPTION CODE CAP COLOR 2 BLACK 1 WHITE 3 RED 4 ORANGE 5 YELLOW 9 GRAY Cap Finish: gloss. Cap supplied not installed. Other colors available, consult Customer Service Center. NOTE: When selecting plunger and cap option, bushing selection must also be made, see below. BUSHING H .300" HIGH THREADED, FLAT Y3 7.6mm THREADED, KEYWAY NONE NO BUSHING CHOICE REQUIRED (JXX ACTUATORS) H9 .300" HIGH UNTHREADED, FLAT 1/4±40 UNS-2A H bushing standard with C, W, Z or Z3 terminations. H9 bushing standard with A, A3, AV2, AV3, or Withstands 12 in./lbs. of torque with no distortion. V3-V31 terminations. Withstands 12 in./lbs. of torque with no distortion. NOTE: When selecting bushing option, plunger selection must also be made, see above. No bushing option choice required when any JXX actuator option is selected. NOTE. Two mounting nuts, locking ring and lockwasher supplied standard with threaded bushings. Optional mounting nut and locking ring styles and finishes available, see section “Technical Data and Additional Hardware”. Third Angle Projection Dimensions are shown: Inches (mm) Specifications and dimensions subject to change www.ck-components.com A-55 8060 Series Alternate Action and Momentary Pushbutton Switches TERMINATIONS A C PC THRU-HOLE Z SOLDER LUG PC MOUNTING SPDT and DPDT SPDT and DPDT Not available with P, S or R contact material. Z3 QUICK CONNECT W WIRE WRAP .750 (19,05) Not available with P, S or R contact material. Mating quick connector available; SPDT and DPDT order part number 530100000, page A-61. SPDT and DPDT A RIGHT ANGLE, PC THRU- HOLE .130 (3,3) .138 (3,51) SECTION A-A 8161SH9ABE2 SPDT A3 RIGHT ANGLE, SNAP-IN, PC THRU-HOLE PC MOUNTING NOTE: PC pattern must clear switch support leg. Not available with I seal. Terminal bend radii and lead-in manufacturing option. Third Angle Projection Dimensions are shown: Inches (mm) Specifications and dimensions subject to change www.ck-components.com A-56 Pushbutton Pushbutton 8060 Series Alternate Action and Momentary Pushbutton Switches TERMINATIONS A A RIGHT ANGLE, PC THRU-HOLE 8261SH9ABE2 DPDT SECTION A-A A3 RIGHT ANGLE, SNAP-IN, PC THRU-HOLE PC MOUNTING Not available with I seal. Terminal bend radii and lead-in manufacturing option. AV2 VERTICAL RIGHT ANGLE, PC THRU-HOLE, .150" PITCH 8161SH9AV2BE2 SPDT AV3 VERTICAL RIGHT ANGLE, SNAP-IN, PC THRU-HOLE, .150" PITCH PC MOUNTING Not available with I seal. Terminal bend radii and lead-in manufacturing option. Third Angle Projection Dimensions are shown: Inches (mm) Specifications and dimensions subject to change www.ck-components.com A-57 8060 Series Alternate Action and Momentary Pushbutton Switches TERMINATIONS A AV2 VERTICAL RIGHT ANGLE, PC THRU-HOLE, .150" PITCH 8261SH9AV2BE2 DPDT SECTION A-A AV3 VERTICAL RIGHT ANGLE, SNAP-IN, PC THRU-HOLE, PC MOUNTING .150" PITCH Not available with I seal. Terminal bend radii and lead-in manufacturing option. V6 VERTICAL MOUNT, V-BRACKET PC MOUNTING V21 VERTICAL MOUNT, V-BRACKET, SNAP-IN OPTION CODE DIM ‘A’ 8161SH9__BE2 V21 .555 (14,10) SPDT V6 .460 (11,68) Not available with I seal. V6 VERTICAL MOUNT, V-BRACKET PC MOUNTING V21 VERTICAL MOUNT, V-BRACKET, SNAP-IN OPTION CODE DIM ‘A’ V21 .555 (14,10) 8261SH9__BE2 DPDT V6 .460 (11,68) Not available with I seal. Third Angle Projection Dimensions are shown: Inches (mm) Specifications and dimensions subject to change www.ck-components.com A-58 Pushbutton Pushbutton 8060 Series Alternate Action and Momentary Pushbutton Switches TERMINATIONS A V3, V4 VERTICAL MOUNT, V-BRACKET V31 VERTICAL MOUNT, V-BRACKET, SNAP-IN PC MOUNTING 8161SH9__BE2 SPDT OPTION CODE DIM ‘A’ V3, V31 .460 (11,68) V4 .630 (16,00) Not available with I seal. V3, V4 VERTICAL MOUNT, V-BRACKET V31 VERTICAL MOUNT, V-BRACKET, SNAP-IN PC MOUNTING 8261SH9__BE2 DPDT SNAP-IN OPTION CODE DIM ‘A’ V3, V31 .460 (11,68) Not available with I seal. V4 .630 (16,00) CONTACT MATERIAL OPTION TERMINAL CONTACT CODE PLATING RATINGS MATERIAL B 1 GOLD 1 GOLD 0.4 VA MAX. @ 20 V AC OR DC MAX. LOW LEVEL/DRY CIRCUIT 6 MATTE-TIN P Q 5 SILVER 6 AMPS @ 120 V AC OR 28 V DC; 4,5 SILVER POWER 3 AMPS @ 250 V AC. 6 MATTE-TIN S G 0.4 VA MAX @ 20 V AC OR DC MAX. OR 3 GOLD GOLD OVER LOW LEVEL/DRY CIRCUIT OR POWER 6 AMPS @ 120 V AC OR 28 V DC; 2,3 6 SILVER MATTE-TIN R 3 AMPS @ 250 V AC. * Note: See Technical Data section of this catalog for RoHS compliant and compatible definitions and specifications. 1 CONTACTS & TERMINALS: Copper alloy, with gold plate over nickel plate. All models with all options when ordered with S, R, G, or Q 2 END CONTACTS: Coin silver, with gold plate over nickel plate. contact material. 3 CENTER CONTACTS & ALL TERMINALS: Copper alloy, with gold plate B contact material standard with all terminations except C, Z & Z3. over nickel plate. Q contact material standard with C, Z & Z3 terminations. 4 END CONTACTS: Coin silver, silver plated. P, S & R contact materials not available with Z & Z3 terminations. 5 CENTER CONTACT & ALL TERMINALS: Copper alloy, silver plated. 6 TERMINALS: Copper alloy, with matte-tin over nickel plate. NOTE: Any models supplied with P, S, R,Q, B or G contact material are RoHS compliant. Third Angle Projection Dimensions are shown: Inches (mm) Specifications and dimensions subject to change www.ck-components.com A-59 8060 Series Alternate Action and Momentary Pushbutton Switches SEAL A E EPOXY SEAL I EPOXY POTTED BASE NOTE: Available with C, W, Z, Z3 terminations only. AVAILABLE HARDWARE Cap Cap Cap .200 DIA. (5,08 ) .120 (3,05) .155 (3,94) PART NO. PART NO. PART NO. 708901000 WHITE 752701000 WHITE 801801000 WHITE 708902000 BLACK 752702000 BLACK 801802000 BLACK 708903000 RED 752703000 RED 801803000 RED 708904000 ORANGE 752704000 ORANGE 801804000 ORANGE 708905000 YELLOW 752705000 YELLOW 801805000 YELLOW 708909000 GRAY 752709000 GRAY 801809000 GRAY Material: Nylon Material: Nylon Material: Nylon Finish: Gloss Finish: Gloss Finish: Gloss Cap, Snap-fitting plunger Cap, Snap-fitting plunger Cap, J80, J81 & J82 options only PART NO. PART NO. PART NO. PART NO. 452D01000 WHITE 894101000 WHITE 484601000 WHITE 798201000 WHITE 452D02000 BLACK 894102000 BLACK 484602000 BLACK 798202263 BLACK 452D03000 RED 894103000 RED 484603000 RED 798203000 RED 452D04000 ORANGE 894104000 ORANGE 484604000 ORANGE 798204000 ORANGE 452D05000 YELLOW 894105000 YELLOW 484605000 YELLOW 798205000 YELLOW 452D09000 GRAY 894109000 GRAY 484609000 GRAY 798209000 GRAY Material: Nylon Material: Nylon Material: Nylon Material: Nylon Finish: Gloss Finish: Gloss Finish: Gloss Finish: Matte Cap, J86 & J96 options only Frame Frame PART NO. PART NO. 459701000 476801000 WHITE PART NO. PART NO. 459702000 476802000 BLACK 615602263 BLACK 613302263 BLACK 459703000 476803000 RED 459704000 476804000 ORANGE Material: Nylon Material: Nylon 459705000 476805000 YELLOW Finish: Matte Finish: Matte 459709000 476809000 GRAY Material: Nylon Material: Nylon Finish: Gloss Finish: Matte NOTE: Additional nuts, locking rings and lockwashers available separately, see section “Technical Data and Additional Hardware”. Third Angle Other cap & frame colors available, consult Customer Service Center. Projection Dimensions are shown: Inches (mm) Specifications and dimensions subject to change www.ck-components.com A-60 Pushbutton Pushbutton 8060 Series Alternate Action and Momentary Pushbutton Switches AVAILABLE HARDWARE A Fits Z3 Termination female connector PART NO. 530100000 Available in loose pieces. Frames snap into panel opening and are independent from switch mounting. Accurate positioning of the PC TYPICAL APPLICATION mounted switch relative to the panel opening is necessary to provide proper clearance between actuator and frame. Available in two basic styles and four panel thicknesses .047-.125 in. Material: Nylon. Finish: Matte. .047" (1,19) PANEL THK. .062" (1,57) PANEL THK. .090" (2,29) PANEL THK. .125" (3,18) PANEL THK. PART NO. PART NO. PART NO. PART NO. 432502263 432602263 432702263 432802263 BLACK Panel Inserts Above frames (part nos. 432XXXXXX) are also available with insert which accepts LED for indicator light assembly. Order insert separately from frame. Blank insert panel (without hole for LED) also available. LED not included. PANEL INSERT BLANK PANEL INSERT WITH HOLE FOR LED WITHOUT HOLE FOR LED PART NO. PART NO. 894902000 476602000 BLACK Special colors, custom markings available, consult Customer Service Center. LED INFORMATION SWITCHES WITH LED SUPPLIED: J86 OPTION: Rectangular LEDs are supplied on 8060 Series pushbutton switches with J86 option. These LEDs are factory installed and are not replaceable. The following specifications apply: MAX RATINGS AT 25ºC AMBIENT TEMPERATURE .025 SQ. TYP. TYP. Flat denotes .200 DIA. TYP. (0,63) cathode. OPTION TYP. FORWARD FORWARD FORWARD CONTINUOUS POWER (5,08˘) CODE COLOR INTENSITY VOLTAGE CURRENT VOLTAGE FORWARD CURRENT DISSIPATION 6 Green 1.0 mcd 20 mA 50 mA 125 mW .030 .230 DIA. 2.1 V 2.5 V 3 Red* 0.5 mcd 10 mA 30 mA 75 mW (0,76) (5,84˘) .750 5 Yellow 4.0 mcd 20 mA 50 mA 125 mW .340 (19,05) (8,64) Process Information: Soldering to LED leads must be completed within 5 seconds at Suggested LED for J82 & J84 options. Dimensions for reference only. 500ºF (260ºC) maximum. Caution: Circuit elements must limit forward current of LED to 50mA max. continuous. * Extra-bright red LED available (typ. intensity 4.5 mcd), consult Customer Service Center. LEDs are not supplied with J82 & J84 options. LED snaps into switch frame surrounding actuator and is wired externally. Third Angle Projection Dimensions are shown: Inches (mm) Specifications and dimensions subject to change www.ck-components.com A-61