Elite.Parts Manufacturers B BOURNS PCW1J-B24-KAB502
About product Specifications Features Datasheet FAQ

BOURNS PCW1J-B24-KAB502

Description

Bourns PCW1J-B24-KAB502 Panel Control Module - PANEL CONTROL - 22MM-ST-CP

Part Number

PCW1J-B24-KAB502

Price

Request Quote

Manufacturer

BOURNS

Lead Time

Request Quote

Category

PRODUCTS - P

Specifications

70,000 Feet

500 VAC minimum

Absolute Minimum Resistance

5 ohms maximum

Audio

0.25 watt

Audio Tapers

1 K ohms to 500 K ohms

Contact Resistance Variation

±5 % maximum
7 % of total resistance

Detents

Center, 10, 20, 30, none

Dielectric Withstanding Voltage (MIL-STD-202, Method 301):Sea Level

1,000 VAC minimum

Effective Electrical Angle

270 ° ± 5 °

Ganging

1 cup maximum

Hardware

One lockwasher & one mounting nut is shipped w/ each potentiometer, except where noted in the part number

Independent Linearity

±5%

Insulation Resistance (500 V)

1,000 ohms minimum

IP Rating

IP 40

Load Life

1,000 Hours @ Rated Power, 20 % RH, 70ºC

Marking

Manufacturer’s trademark, resistance value, part number, and date code

Mechanical Angle

300 ° ± 5 °

Moisture Resistance

MIL-STD-202, Method 103, Condition B

Mounting

79.09 N-cm (7 lb.-in.) maximum

Power Rating @ 70 ºC (Voltage Limited by Power Dissipation or 350 VAC, Whic

0.75 watt

Rotational Life (No Load)

50,000 cycles

Running (Undetented)

0.18 to 1.06 N-cm (0.25 to 1.5 oz.-in.)

Shock

50 G

Soldering Condition:Manual Soldering

96.5Sn/3.0Ag/0.5Cu solid wire or no-clean rosin cored wire; 370°C (700°F) max. for 3 seconds

Standard Resistance Range:Linear Tapers

500 ohms to 1 megohm

Starting (Undetented)

1.5 N-cm (2.25 oz.-in.) maximum

Stop Strength (1/4 ” and 6 mm Shaft Diameters)

79.09 N-cm (7 lb.-in.)

Temperature

Operating:+1°C to +125°C; Storage:-40°C to +125°C

Temperature Coefficient Over Storage Temperature Range

±1000 ppm/°C

Terminals

PC pin or solder lug

Theoretical Resolution

Essentially infinite

Torque:Starting (Detented)

0.5-1.5 N-cm (0.75-2.25 oz.-in.)

Total Resistance Shift

±1 % maximum
±10 % maximum
±20 % maximum

Total Resistance Shift (Audio taper)

±20 % maximum

Total Resistance Shift (Linear taper)

±10 ohms or 12 %, whichever is greater

Total Resistance Tolerance

±20%

Vibration

20 G

Voltage Ratio Shift

±20 % maximum

Wash processes

Not recommended

Wave Soldering

96.5Sn/3.0Ag/0.5Cu solder with no-clean flux; 260°C (500°F) max. for 5 seconds

Weight (Single Section)

21 gm (0.75 oz.) maximum

Features

Datasheet

pdf file

Bourns-PCW1J-B24-KAB502-datasheet1-2047032438.pdf

310 KiB

Extracted Text

Features ■ RoHS compliant* ■ Linear or audio taper versions ■ Space saving design ■ Wide range of resistance values ■ PC pin or solder lug terminals ■ Metric shaft and bushing option ■ Mounting brackets available PC - “Slimline” 22 mm Square Single Turn Panel Control Electrical Characteristics Standard Resistance Range Linear Tapers.....................................................................................................................................................................................500 ohms to 1 megohm Audio Tapers....................................................................................................................................................................................1 K ohms to 500 K ohms Total Resistance Tolerance ...............................................................................................................................................................................................±20 % Independent Linearity .........................................................................................................................................................................................................±5 % Absolute Minimum Resistance........................................................................................................................................................................5 ohms maximum Effective Electrical Angle ............................................................................................................................................................................................270 ° ± 5 ° Contact Resistance Variation ..................................................................................................................................................................7 % of total resistance Dielectric Withstanding Voltage (MIL-STD-202, Method 301) Sea Level ................................................................................................................................................................................................1,000 VAC minimum 70,000 Feet................................................................................................................................................................................................500 VAC minimum Insulation Resistance (500 V) ....................................................................................................................................................................1,000 ohms minimum Power Rating @ 70 ºC (Voltage Limited by Power Dissipation or 350 VAC, Whichever is Less) Linear........................................................................................................................................................................................................................ .75 watt Audio ........................................................................................................................................................................................................................ .25 watt Theoretical Resolution.....................................................................................................................................................................................Essentially infinite Environmental Characteristics Operating Temperature Range .........................................................................................................................................................................+1 °C to +125 °C Storage Temperature Range ...........................................................................................................................................................................-40 °C to +125 °C Temperature Coefficient Over Storage Temperature Range ................................................................................................................................±1000 ppm/°C Vibration ...............................................................................................................................................................................................................................20 G Total Resistance Shift.....................................................................................................................................................................................±1 % maximum Voltage Ratio Shift .......................................................................................................................................................................................±20 % maximum Shock ...................................................................................................................................................................................................................................50 G Total Resistance Shift.....................................................................................................................................................................................±1 % maximum Voltage Ratio Shift .......................................................................................................................................................................................±20 % maximum Load Life .............................................................................................................................................................1,000 Hours @ Rated Power, 20 % RH, 70 ºC Total Resistance Shift...................................................................................................................................................................................±10 % maximum Rotational Life (No Load) .......................................................................................................................................................................................50,000 cycles Total Resistance Shift (Linear taper)........................................................................................................................±10 ohms or 12 %, whichever is greater Total Resistance Shift (Audio taper).............................................................................................................................................................±20 % maximum Contact Resistance Variation .............................................................................................................................................................................±5 % maximum Moisture Resistance ....................................................................................................................................................MIL-STD-202, Method 103, Condition B Total Resistance Shift...................................................................................................................................................................................±20 % maximum IP Rating ..............................................................................................................................................................................................................................IP 40 Mechanical Characteristics Stop Strength (1/4 ” and 6 mm Shaft Diameters) ......................................................................................................................................79.09 N-cm (7 lb.-in.) Mechanical Angle .......................................................................................................................................................................................................300 ° ± 5 ° Torque Starting (Detented)................................................................................................................................................................0.5-1.5 N-cm (0.75-2.25 oz.-in.) Starting (Undetented)..........................................................................................................................................................1.5 N-cm (2.25 oz.-in.) maximum Running (Undetented) ................................................................................................................................................ 0.18 to 1.06 N-cm (0.25 to 1.5 oz.-in.) Mounting...............................................................................................................................................................................79.09 N-cm (7 lb.-in.) maximum Weight (Single Section) .....................................................................................................................................................................21 gm (0.75 oz.) maximum Terminals......................................................................................................................................................................................................PC pin or solder lug Soldering Condition Manual Soldering......................................................................................................................96.5Sn/3.0Ag/0.5Cu solid wire or no-clean rosin cored wire 370 °C (700 °F) max. for 3 seconds Wave Soldering ..............................................................................................................................................96.5Sn/3.0Ag/0.5Cu solder with no-clean flux 260 °C (500 °F) max. for 5 seconds Wash processes ........................................................................................................................................................................................Not recommended Marking ....................................................................................................................Manufacturer’s trademark, resistance value, part number, and date code Ganging..............................................................................................................................................................................................................1 cup maximum Hardware.............................................One lockwasher and one mounting nut is shipped with each potentiometer, except where noted in the part number. Detents ..................................................................................................................................................................................................Center, 10, 20, 30, none For additional features or specifications not shown, consult factory. FOR ORDERING INFORMATION SEE PAGE 4. *RoHS Directive 2002/95/EC Jan 27 2003 including Annex Specifications are subject to change without notice. Specifications are subject to change without notice. Customers should verify actual device performance in their specific applications. Customers should verify actual device performance in their specific applications. *RoHS COMPLIANT PC - “Slimline” 22 mm Square Single Turn Panel Control Product Dimensions Axial PC Pins 14.7 ± 0.5 DIA. (.578 ± .020) "F" 7.42 22.2 ± 0.25 11.1 (.292) (.874 ± .010) PANEL HOLE DIMENSIONS (.437) "L" 9.53 (.375) 12 3 9.0 DIA. 3.18 9.14 (.354) DIA. DIA. 0.79 (.125) (.360) M9 X 0.75-6g SPL 3 PLCS. (.031) .320 11.1 1.52 (8.13) "E" 2 PLCS. (.437) (.060) 6.25 (.246) 6.35 9.53 2.54 5.08 "F" = OR "E" = OR (.250) (.375) (.100) (.200) "L" = SEE SHAFT LENGTH TABLE 22.2 ± 0.25 Radial PC Pins (.874 ± .010) .320 11.1 "L" (8.13) (.437) 14.7 ± 0.5 PANEL HOLE DIMENSIONS "F" (.578 ± .020) 9.53 DIA. (.375) 12 3 8.36 3.18 9.14 DIA. DIA. (.329) (.125) (.360) 11.1 (.437) .28 0.79 6.25 (.011) 3 PLCS. (.031) (.246) "E" 2 PLCS. 3 PLCS. 6.35 9.53 2.54 5.08 "F" = OR "E" = OR (.250) (.375) (.100) (.200) "L" = SEE SHAFT LENGTH TABLE TOLERANCES EXCEPT WHERE NOTED: MM 2 DIMENSIONS ARE: .25 (INCHES) .XX = ± (.010) 3 .13 1 .XXX = ± (.005) Specifications are subject to change without notice. Customers should verify actual device performance in their specific applications. PC - “Slimline” 22 mm Square Single Turn Panel Control Product Dimensions SOLDER LUGS "L" (Dimensions not given are the same as "F" Axial PC pins. 22.2 ± 0.25 (.874 ± .010) 8.36 (.329) 1.02 X 2.29 3 PLCS. (.040 X .090) 7.75 6.35 9.53 .28 5.08 "F" = OR (.305) 3 PLCS. 6.25 2.03 (.250) (.375) (.011) (.200) 3 PLCS. (.246) (.080) 2 PLCS. 6.83 Axial PC PINS 23.37 "L" (.269) 11.43 (.92) With Rear Mounting Bracket 8.31 15.2 (.450) (.327) (.600) 2 PLCS. 18.87 0.76 (.743) "E" 2 PLCS. (.030) 17.07 4 PLCS. (.672) 1.19 DIA. 7 PLCS. (.047) 2.54 5.08 5.87 "E" = OR (.100) (.200) (.231) 1.19 5.48 DIA. 7 PLCS. (.047) Radial PC PINS 23.37 (.216) (.92) With Side Mounting Bracket "L" 7.62 (.300) 2 PLCS. 5.08 17.07 "E" 2 PLCS. (.200) (.672) 11.43 12.62 2 PLCS. (.450) (.497) 6.83 (.269) 2.54 5.08 "E" = OR (.100) (.200) 0.76 0.79 4 PLCS. 3 PLCS. (.030) (.031) "E" 2 PLCS. SHAFT STYLES AND ORIENTATION (Full CCW Rotation) Shaft Style C Shaft Style J Shaft Style R Shaft Style B Shaft Style Y 6.00 6.32 + 0.03/ - 0.08 3.94 + .051/ - .025 5.54 ± .076 4.7 DIA. 1.57 (.236) (.249 + .001/ - .003) DIA. (.218 ± .003) (.155 + .002/ - .001) (.062) (.185) DIA. 4.75 ± .051 6.32 + 0.03/ - 0.08 1.19 1.19 "D" DIA. "D" 1.6 (.187 ± .002) (.047) 1.6 (.047) (.249 + .001/ - .003) (.063) DIA. (.063) Slot depth (Y shaft) 9.65 (.380) for shafts <1 " (2.54) length; "D" dimensions extend from shaft end to bushing face "D" = (shaft length, FMS) – (bushing length) 14.7 (.520) for shafts ≥1 " (2.54) length Shaft Orientations Shaft Styles C, J Shaft Styles B, R Shaft Style Y 60 ° ± 2 ° 60 ° ± 2 ° 120 ° ± 2 ° MM DIMENSIONS: (IN.) TOLERANCES EXCEPT WHERE NOTED: .25 .XX = ± (.010) .13 .XXX = ± (.005) Specifications are subject to change without notice. Customers should verify actual device performance in their specific applications. How to Order PC “Slimline” Panel Controls PC W 1 J - B 2 4 - B A B 1 0 3 L RoHS IDENTIFIER Code Description L Compliant SHAFT LENGTH (FMS) RESISTANCE VALUES Available Shaft Code TR Code TR Code TR Code Description Styles 501 500 Ω 103 10 KΩ 104 100 KΩ 16 1/2 ” (12.7 mm) Length B 102 1 KΩ 203 20 KΩ 254 250 KΩ 20 5/8 ” (15.9 mm) Length J 252 2.5 KΩ 253 25 KΩ 504 500 KΩ 24 3/4 ” (19 mm) Length B, C, J, Y 502 5 KΩ 503 50 KΩ 105 1 MΩ 28 7/8 ” (22.2 mm) Length B, C, J, Y 32 1 ” (25.4 mm) Length B, C, J, Y 36 1-1/8 ” (28.6 mm) Length B, C, J, Y Metric ELEMENT TAPER VERSIONS 19 19 mm Length R Code Taper Description 22 22 mm Length R B Lin. CP ±20 % 24 24 mm Length R D CW Audio CP ±20 % G CCW Audio CP ±20 % SHAFT STYLES (See Outline Drawing) Code Description B 1/4 ” (6.35 mm) Dia. Slotted DETENT CONFIGURATIONS C 1/4 ” (6.35 mm) Dia. Flatted Code Taper Description J 3/16 ” (4.76 mm) Dia. Flatted A No Detents R 6 mm Dia. Slotted B 10 Detents (Use Metric Lengths Only) C Center Detent Only Y 3/16 ” (4.76 mm) Dia. Split Shaft D 20 Detents E 30 Detents F CCW Detent Only ANTI-ROTATION LUG Code Description J 9:00 Position D None HOUSING TERMINAL CONFIGURATION Code Features A B C D E F G H J K L M N Rear Mounting Bracket X XX X NO. SECTIONS Side Mounting Bracket X X X X 1 Single Axial Terminals .100 ” (2.54 mm) Centers X X X Radial Terminals .100 ” (2.54 mm) Centers X X X Radial Terminals .200 ” (5.08 mm) Centers X X X Solder Lugs .200” (5.08 mm) Centers X BUSHING CONFIGURATION Axial Terminals .200 ” (5.08 mm) Centers X X X Available Shaft Hardware Included X X X X X X X X X Code Description Styles W 9 mm x .250 ” (6.35 mm) Length All Threaded M9 x 0.75 6g 5 Pl Panel mount hardware not included as standard on bracketed versions. L 9 mm x .375 ” (9.53 mm) Length B, C, R The sample part number demonstrates the identification code for Bourns Threaded M9 x 0.75 6g 5 Pl Slimline Potentiometers. The part number shown is a commonly used model, typically available from stock. Boldface features are Bourns standard options. All others are available with higher minimum order quantities. Asia-Pacific: Tel: +886-2 2562-4117 • Fax: +886-2 2562-4116 Europe: Tel: +41-41 768 5555 • Fax: +41-41 768 5510 The Americas: Tel: +1-951 781-5500 • Fax: +1-951 781-5700 REV. 08/09 www.bourns.com Specifications are subject to change without notice. Customers should verify actual device performance in their specific applications.

Frequently asked questions

What makes Elite.Parts unique?

chervon down
At GID Industrial (Elite.Parts' parent company), we specialize in procuring industrial parts. We know where to find the rare and obsolete equipment that our customers need in order to get back to business. There are other companies who claim to do what we do, but we're confident that our commitment to quality and value is unparalleled in our field.

What kind of warranty will the PCW1J-B24-KAB502 have?

chervon down
Warranties differ by part and by which suppliers we use to procure it for you. Sometimes, a part will be sold as-is and without a warranty. Our specialty, single board computers, tend to receive a one-year warranty.

Which carriers does Elite.Parts work with?

chervon down
Elite.Parts can ship via FedEx, UPS, DHL, and USPS. We have accounts with each of them and generally ship using one of those, but we can also ship using your account if you would prefer. However, we can use other carriers if it will be more convenient for you.

Will Elite.Parts sell to me even though I live outside the USA?

chervon down
Absolutely! We are happy to serve customers regardless of location. We work with international clients all the time, and we are familiar with shipping to destinations all across the globe.

I have a preferred payment method. Will Elite.Parts accept it?

chervon down
All major credit cards are accepted: Visa, MasterCard, Discover, and American Express. We will also accept payment made with wire transfer or PayPal. Checks will only be accepted from customers in the USA. Terms may available for larger orders, upon approval.

Why buy from GID?

quality

Quality

We are industry veterans who take pride in our work

protection

Protection

Avoid the dangers of risky trading in the gray market

access

Access

Our network of suppliers is ready and at your disposal

savings

Savings

Maintain legacy systems to prevent costly downtime

speed

Speed

Time is of the essence, and we are respectful of yours

What they say about us

FANTASTIC RESOURCE

star star star star star

One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!

Bucher Emhart Glass

EXCELLENT SERVICE

star star star star star

With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.

Fuji

HARD TO FIND A BETTER PROVIDER

star star star star star

Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.

Applied Materials

CONSISTENTLY DELIVERS QUALITY SOLUTIONS

star star star star star

Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.

Nidec Vamco

TERRIFIC RESOURCE

star star star star star

This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.

Trican Well Service

GO TO SOURCE

star star star star star

When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.

ConAgra Foods

Related Products

PANEL CONTROL - 22MM-ST-CP

PANEL CONTROL - 22MM-ST-CP

PANEL CONTROL - 22MM-ST-CP

PANEL CONTROL - 22MM-ST-CP

PANEL CONTROL - 22MM-ST-CP

PANEL CONTROL - 22MM-ST-CP