Q08 Series Opposed-Mode Sensors Low-profile infrared sensors in rugged metal housings Q08 Series Diffuse-Mode Sensor Features • Miniature right-angle dc photoelectric sensors in rugged die-cast metal housings • Ultra-thin; only 8 mm (0.3") deep •Totally self-contained; 10 to 30V dc operation • Easy mechanical alignment • Circuitry is completely sealed and epoxy-encapsulated; rated IP67 and NEMA 6 • Select models with NPN (sinking) or PNP (sourcing) output • Select light operate or dark operate models • 3-wire hookup; output load capacity to 150 milliamps • LED indicators for Power ON and Output ON; Output indicator may be used for alignment • Choose 2 m (6.5') standard integral cable length; or 9 m (30') cable; quick- disconnect models with Pico-style connectors are also available. Mating cables are ordered separately (see page 4). Infrared, 880 nm Q08 Series Diffuse-Mode Models Supply Output Excess Gain Beam Pattern Models* Range Cable Voltage Type Performance based on 90% reflective white test card NO5-Q08-AN7 2 m (6.5') NPN/LO 1000 NO5-Q08-AN7-V1131 3-Pin Pico QD E Q08 X Diffuse Mode Q08 7.5 mm .3 in C NO5-Q08-RN7 2.5 mm 2 m (6.5') Diffuse Mode 100 E 5.0 mm .2 in NPN/DO S NO5-Q08-RN7-V1131 to 61 3-Pin Pico QD 2.5 mm .1 in S 0 0 mm 10-30V dc 10 G 2.5 mm .1 in (0.1" to NO5-Q08-AP7 2 m (6.5') A 5.0 mm .2 in PNP/LO I 2.4") NO5-Q08-AP7-V1131 3-Pin Pico QD 7.5 mm .3 in N 1 0 12.5 mm 25.0 mm 37.5 mm 40.0 mm 52.5 mm 1 mm 10 mm 100 mm 1000 mm 0.5 in 1.0 in 1.5 in 2.0 in 2.5 in 0.04 in 0.4 in 4.0 in 40 in NO5-Q08-RP7 2 m (6.5') DISTANCE PNP/DO DISTANCE NO5-Q08-RP7-V1131 3-Pin Pico QD *NOTES: • 9 m (30') cables are available by adding suffix “W/30” to the model number of the cabled version (e.g., NO5-Q08-AN7 W/30). • A model with a QD connector (identified by the suffix V1131 in the model number) requires an accessory mating cable. See page 4 for more information. WARNING . . . Not To Be Used for Personnel Protection Never use these products as sensing devices for personnel protection. Doing so could lead to serious injury or death. ! These sensors do NOT include the self-checking redundant circuitry necessary to allow their use in personnel safety applications. A sensor failure or malfunction can cause either an energized or de-energized sensor output condition. Consult your current Banner Safety Products catalog for safety products which meet OSHA, ANSI and IEC standards for personnel protection. Printed in USA 05/02 P/N 03558 rev. C For Sales and Support, Contact Walker EMD • Toll-free: (800) 876-4444 • Tel: (203) 426-7700 • Fax: (203) 426-7800 • www.walkeremd.com Q08 Series Diffuse-Mode Sensors Q08 Series Diffuse-Mode Sensor Overview This small, rugged infrared diffuse proximity mode sensor is contained within an 8- mm deep die-cast metal housing. It is totally self-contained, and is powered by 10 to 30V dc. It is ideal for sensing of any reflective surface at up to 2" from the sensor face. Typical applications include parts detection on small conveyors and in robot grippers, and other similar short-range sensing applications. Q08 diffuse sensors have a solid-state output capable of switching loads of up to 150 mA dc, continuous. Four output types are available: NPN sinking/light operate, NPN sinking/dark operate, PNP sourcing/light operate, and PNP sourcing/dark operate. A light-operate output conducts when the sensor sees the reflection of its own modulated light (an object is present). A dark-operate output conducts when the sensor does not see the reflection of its own modulated light (no object is present). A green LED indicator, visible from the front and left side of the sensor, lights whenever dc power is applied to the sensor. A yellow LED, visible from the front and right side of the sensor, lights whenever the sensor output is conducting. Figure 1. Q08 Series Diffuse-Mode features 8.0 mm (0.32") 20.0 mm (0.79") 32.0 mm 39.1 mm (1.26") (1.54") 3.00 mm (0.118") ş 3.40 mm (0.134") (2 Holes) 2 m (6.5') Cable #4 (M3) Screw Clearance 3-pin Pico-Style Quick-Disconnect 13.00 mm (0.512") Quick-Disconnect Models Attached Cable Models 9.7 mm (0.38") Optical 7.7 mm Center of (0.30") Beam Optical Center of Sensor Figure 2. Q08 Series Diffuse-Mode Sensor dimensions Banner Engineering Corp. • Minneapolis, MN U.S.A. page 2 www.bannerengineering.com • Tel: 763.544.3164 For Sales and Support, Contact Walker EMD • Toll-free: (800) 876-4444 • Tel: (203) 426-7700 • Fax: (203) 426-7800 • www.walkeremd.com Q08 Series Diffuse-Mode Sensors Q08 Series Diffuse-Mode Sensor Specifications Supply Voltage and Current 10 to 30V dc at 25 mA; 10% maximum ripple Supply Protection Circuitry Protected against reverse polarity Output Configuration Solid-state dc output, with four output types available: NPN sinking/light operate PNP sourcing/light operate NPN sinking/dark operate PNP sourcing/dark operate Light operate outputs conduct when the receiver sees the reflection of its own modulated light source; Dark operate outputs conduct when the sensor sees dark. Output Rating 150mA maximum, continuous Off-state leakage current is 100 microamps at 30V dc On-state saturation voltage is < 200 millivolts at 10 mA dc and < 1 volt at 150 mA dc Output Response Time 1 millisecond ON and OFF independent of signal strength Repeatability 200 microseconds (0.2 milliseconds), independent of signal strength Indicators Two LED indicators: Green: Lights to indicate dc power ON Yellow: Lights when sensor output is conducting (in “light” condition for light operate models; in “dark” condition for dark operate models) Construction Black epoxy-painted die-cast zinc housing, polysulfone thermoplastic lens with two through-mounting holes to accommodate M3 (#4) hardware Environmental Rating Meets NEMA standards 1, 2, 4, 6, 12 and 13; IEC IP67 Connections PVC-jacketed 2 m (6.5') or 9 m (30') cable or 3-pin Pico-style quick-disconnect (QD) fitting available. See page 4. Cable is 4.0 mm (0.16") in diameter. Operating Conditions Temperature: 0° to +50°C (+32° to +122°F) Maximum relative humidity: 90% at 50°C (non-condensing) Application Notes The horizontal axis of the beam pattern represents a line extending outward from the optical center of the Q08 sensor, and perpendicular to the sensor’s lens. For purposes of mounting and alignment, note that the optical center of the Q08’s lens is not the same as its mechanical center. The drawing in figure 2 shows the location of the Q08’s optical center. Certifications Banner Engineering Corp. • Minneapolis, MN U.S.A. page 3 www.bannerengineering.com • Tel: 763.544.3164 For Sales and Support, Contact Walker EMD • Toll-free: (800) 876-4444 • Tel: (203) 426-7700 • Fax: (203) 426-7800 • www.walkeremd.com Q08 Series Opposed-Mode Sensors Q08 Series Diffuse-Mode Sensor Hookups Cabled Models PNP (Sourcing) Cabled Models NPN (Sinking) bu bn – + 10-30V dc 10-30V dc bn bu + – bk bk Load Load QD Models PNP (Sourcing) QD Models NPN (Sinking) (3-Pin Pico-Style) (3-Pin Pico-Style) bu bn – + 10-30V dc 10-30V dc bn bu – + bk bk Load Load Accessories Quick-Disconnect Cables The following cables are available for Q08 Series Diffuse-Mode QD models Style Model Length Dimensions Pin-out ş 10 mm max. (0.4") 3-pin Pico-style PKG3-2 2 m (6.5') straight 28 mm max. Black Wire (1.1") Brown Wire Blue Wire 25 mm max. (1.0") 3-pin 20 mm 2 m (6.5') Pico-style (0.8") PKW3-2 right-angle ş 12 mm max. (0.5") WARRANTY: Banner Engineering Corp. warrants its products to be free from defects for one year. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture found to be defective at the time it is returned to the factory during the warranty period. This warranty does not cover damage or liability for the improper application of Banner products. This warranty is in lieu of any other warranty either expressed or implied. Banner Engineering Corp., 9714 Tenth Ave. No., Minneapolis, MN 55441 • Phone: 763.544.3164 • www.bannerengineering.com • Email: sensors@bannerengineering.com For Sales and Support, Contact Walker EMD • Toll-free: (800) 876-4444 • Tel: (203) 426-7700 • Fax: (203) 426-7800 • www.walkeremd.com