M201EW01 V3 Document Version: 0.2 Date: 2006/02/06 Product Functional Specification 20.1 inch WSXGA+ Color TFT LCD Module Model Name: M201EW01 V3 (u) Preliminary Specification ( ) Final Specification (C) Copyright AU Optronics Ver 0.2 1/30 2005 All Rights Reserved. No Reproduction and Redistribution Allowed. M201EW01 V3 Note: This Specification is subject to change without notice. AU OPTRONICS CORPORATION Product Specification + 20.1”Wide SXGA Color TFT-LCD Module Model Name: M201EW01 V.3 Approved by Prepared by CCChiu Chris Peng DDBU Marketing Division / AU Optronics corporation Customer Checked & Approved by (C) Copyright AU Optronics Ver 0.2 2/30 2005 All Rights Reserved. No Reproduction and Redistribution Allowed. M201EW01 V3 Contents 1.0 Handling Precautions.............................................................6 2.0 General Description...............................................................7 2.1 Display Characteristics .............................................................................................................. 7 2.2 Optical Characteristics............................................................................................................... 8 3.0 Functional Block Diagram .................................................... 12 4.0 Absolute Maximum Ratings ................................................. 13 4.1 TFT LCD Module ...................................................................................................................... 13 4.2 Backlight Unit............................................................................................................................ 13 4.3 Absolute Ratings of Environment............................................................................................ 13 5.0 Electrical characteristics...................................................... 14 5.1 TFT LCD Module ...................................................................................................................... 14 5.1.1 Power Specification............................................................................................... 14 5.1.2 Signal Electrical Characteristics .............................................................................. 15 5.2 Backlight Unit............................................................................................................................ 16 6.0 Signal Characteristic............................................................ 17 6.1 Pixel Format Image................................................................................................................... 17 6.2 The input data format ............................................................................................................... 17 6.3 Signal Description .................................................................................................................... 18 6.4 Timing Characteristics.............................................................................................................. 19 6.4.1 Timing diagram.................................................................................................... 20 6.5 Power ON/OFF Sequence....................................................................................................... 21 7.0 Connector & Pin Assignment ............................................... 22 7.1 TFT LCD Module ...................................................................................................................... 22 7.2 Backlight Unit............................................................................................................................ 23 7.3 Signal for Lamp connector....................................................................................................... 23 8.0 Reliability ............................................................................ 25 9.0 Environment........................................................................ 26 9.1 Temperature and Humidity....................................................................................................... 26 9.1.1 Operating Conditions ............................................................................................ 26 9.1.2 Shipping Conditions.............................................................................................. 26 9.2 Atmospheric Pressure .............................................................................................................. 26 10.0 Safety................................................................................ 27 10.1 Sharp Edge Requirements .................................................................................................... 27 10.2 Materials.................................................................................................................................. 27 10.2.1 Toxicity ............................................................................................................. 27 10.2.2 Flammability ...................................................................................................... 27 (C) Copyright AU Optronics Ver 0.2 3/30 2005 All Rights Reserved. No Reproduction and Redistribution Allowed. M201EW01 V3 10.3 Capacitors ............................................................................................................................... 27 11.0 Other requirement............................................................. 28 11.1 National Test Lab Requirement............................................................................................. 28 11.2 Label ........................................................................................................................................ 28 12.0 Mechanical Characteristics ................................................ 29 (C) Copyright AU Optronics Ver 0.2 4/30 2005 All Rights Reserved. No Reproduction and Redistribution Allowed. M201EW01 V3 Record of Revision Version and Page Old description New Description Remark Date 0.1 All First Edition for Customer All 2006/01/18 0.2 16 FCFL Typ: 50; Max: 60 [KHz] FCFL Typ. 55; Max. 80 [KHz] 2006/02/06 o o ViCFL (0 C) Min:1950 [Volt] ViCFL (0 C) Min: 2120 [Volt] o o ViCF (25 C) Min:1495 [Volt] ViCF (25 C) Min: 1625 [Volt] VCFL Min 740@8mA VCFL Min 750@8mA; Typ 760@7mA Typ 783@7mA; Max 860@3mA Max 936@3mA PCFL Typ: 32[Watt] PCFL Typ: 32.9[Watt] 4.1 TFT LCD Module 4.1 TFT LCD Module 13 Logic/LCD Drive Voltage Max: 6 [Volt] Logic/LCD Drive Voltage Max: 14 [Volt] 5.1.1 Power specification 5.1.1 Power specification 14 IDD Typ 500 Max 550 [mA] IDD Typ 550 Max 650 [mA] 5.1.1 Power specification 5.1.1 Power specification Irush Max:7 [A] Irush Max: 2.5 [A] 5.1.1 Power specification 5.1.1 Power specification PDD Typ:6; Max:7 [Watt] PDD Typ:6.6; Max:8 [Watt] Mating type: Mating type: 12 HRS: MDF76TW-30S-1H(58) F I-X30S-H Mating house part number: Mating house part number: 22 HRS: MDF76TW-30S-1H(58) FI-X30S-H (C) Copyright AU Optronics Ver 0.2 5/30 2005 All Rights Reserved. No Reproduction and Redistribution Allowed. M201EW01 V3 1.0 Handling Precautions 1) Since front polarizer is easily damaged, pay attention not to scratch it. 2) Be sure to turn off power supply when inserting or disconnecting from input connector. 3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots. 4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth. 5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. 6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth when handling. 7) Do not open nor modify the Module Assembly. 8) Do not press or pat the panel surface by fingers,hand or tooling 9) Do not press the reflector sheet at the back of the module to any directions. 10) In case if a module has to be put back into the packing container slot after once it was taken out from the container, do not press the center of the CCFL reflector edge. Instead, press at the far ends of the CCFL reflector edge softly. Otherwise the TFT module may be damaged. 11) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the Interface Connector of the TFT module. 12) After installation of the TFT module into an enclosure (Desktop monitor Bezel, for example), do not twist nor bend the TFT Module even momentary. At designing the enclosure, it should be taken into consideration that no bending/twisting forces are applied to the TFT module from outside. Otherwise the TFT module may be damaged. (C) Copyright AU Optronics Ver 0.2 6/30 2005 All Rights Reserved. No Reproduction and Redistribution Allowed. M201EW01 V3 2.0 General Description This specification applies to the 20.1 inch-wide Color TFT-LCD Module M201EW01. The display supports the WSXGA+ (1680(H) x 1050(V)) screen format and 16.7M colors (RGB 8-bits data). All input signals are 2 Channel LVDS interface compatible. This module does not contain an inverter card for backlight. 2.1 Display Characteristics The following items are characteristics summary on the table under 25 ℃ condition: ITEMS Unit SPECIFICATIONS Screen Diagonal [mm] 511.13 (20.1"Wide) Active Area [mm] 433.44 (H) x 270.90(V) Pixels H x V 1680(x3) x 1050 Pixel Pitch [mm] 0.258 (per one triad) x 0.258 Pixel Arrangement R.G.B. Vertical Stripe Display Mode Normally Black by AUO AMVA 2 White Luminance ( Center ) [cd/m ] 2 @7mA 300 cd/m (Typ) Contrast Ratio 1000 : 1 (Typ) Optical Response Time [msec] 16ms (Typ, on/off) ; 8ms (Average, grey to grey) Color Saturation 72% NTSC Nominal Input Voltage VDD [Volt] +12 V Power Consumption [Watt] 30W(Typ) (w/o Inverter, All white pattern) (VDD line + CCFL line) Weight [Grams] 2950 (Typ) Physical Size [mm] 459.4(W) x 296.4(H) x 22.8(D) (Typ) Electrical Interface Even/Odd R/G/B data, 3 sync signal, Clock Support Color 16.7M colors (RGB 8-bit data ) Temperature Range o Operating [ C] 0 to +50 o Storage (Shipping) [ C] -20 to +60 Surface Treatment Hard-coating (3H), Anti-Glare treatment (C) Copyright AU Optronics Ver 0.2 7/30 2005 All Rights Reserved. No Reproduction and Redistribution Allowed. LCD Module M201EW01 V3 2.2 Optical Characteristics The optical characteristics are measured under stable conditions at 25 ℃: Item Unit Conditions Min. Typ. Max. Note Viewing Angle [degree] Horizontal (Right) 75 89 - [degree] CR = 10 (Left) 75 89 - [degree] Vertical (Up) 75 89 - [degree] CR = 10 (Down) 75 89 - Contrast ratio Normal Direction 750 1000 Response Time [msec] Rising Time - 11 25 Note 1 [msec] Falling Time - 5 15 Note 1 [msec] Rising + Falling - 16 40 Note 1 [msec] Grey to Grey Note 2 - 8 - (average) Color / Chromaticity Red x 0.610 0.641 0.670 Coordinates (CIE) Red y 0.322 0.353 0.382 Green x 0.258 0.289 0.318 Green y 0.598 0.626 0.658 Blue x 0.114 0.142 0.174 Blue y 0.046 0.078 0.106 White x 0.283 0.343 Color Coordinates (CIE) White 0.313 White y 0.299 0.359 0.329 White Luminance at CCFL 7.0mA 2 [cd/m ] (central point) 240 300 - Luminance Uniformity [%] 75 80 - Note 3 Crosstalk (in75Hz) [%] 1.5 Note 4 Flicker DB -20 Note 5 Equipment: Pattern Generator, Power Supply, Digital Voltmeter, Luminance meter (PR 880, BM-5A , BM 7 ,CS-1000, & EZContrast* ) Aperture : 1∘with 100cm viewing distance (VD) or 2 ∘with 50cm viewing distance (VD) Test Point: Center (VESA point 9) Environment: < 1 lux PR-880 / BM5A / BM7 /CS-1000 measuring distance 0 Module Driving Equipment (C) Copyright AU Optronics Ver 0.2 8/30 2005 All Rights Reserved. No Reproduction and Redistribution Allowed. M201EW01 V3 *’ EZ Contrast is different measurement tool with very close viewing distance. Note 1: Definition of Response time The output signals of photodetector are measured when the input signals are changed from “Black ” to “White” (rising time), and from “White ” to “Black ”(falling time), respectively. The response time is interval between the 10% and 90% of amplitudes. Note 2: Over-Drive and Response time: B A Time 100% 90% 10% 0% Tr Tf Time Algorithm: Level A - Level B ³ 16 then average Tr ≦8ms & average Tf ≦8ms (C) Copyright AU Optronics Ver 0.2 9/30 2005 All Rights Reserved. No Reproduction and Redistribution Allowed. Optical Response Driving Signal M201EW01 V3 Note 3: Brightness uniformity of these 9 points is defined as below 90 % 50 % 10 % 10 % 50 % 90 % Minimum Luminance in 9 points (1- 9) Uniformity = x 100% Maximum Luminance in 9 Points (1- 9) Note 4: Crosstalk is defined as below : 1/2 1/6 2/3 1/2 1/3 1/6 1/6 A A ’ 1/6 1/3 1/2 1/2 B B’ 2/3 184 gray level 184 gray level Unit: percentage of dimension of display area 0 gray level l L -L l / L x 100%= 1.5% max., L and L are brightness at location A and B A A’ A A B l L -L l / L x 100%= 1.5% max., L and L are brightness at location A ’ and B ’ B B’ B A’ B’ (C) Copyright AU Optronics Ver 0.2 10/30 2005 All Rights Reserved. No Reproduction and Redistribution Allowed. M201EW01 V3 Note5: Test Paterm: Subchecker Pattern R G B R G B Gray Level = L127 R G B R G B Gray Level = L0 R G B R G B Method: Record dBV & DC value with (WESTAR)TRD-100 Amplitude AC DC Time AC Level(at 30 Hz) Flicker (dB) = 20 log DC Level 3.0 Functional Block Diagram The following diagram shows the functional block of the 20.1 inches wide Color TFT/LCD Module: (C) Copyright AU Optronics Ver 0.2 11/30 2005 All Rights Reserved. No Reproduction and Redistribution Allowed. Y-Driver IC Connector M201EW01 V3 AUO ASIC G1 LVDS TFT-LCD Receiver Timing LVDS 1680*(3)*1050 Controller Pixels Over-Driver +12V X-Driver IC G1050 D1 D5040 6 CCFL Gamma DC/DC Correction Converter DC POWER I/F + X-PCB Inverter JAE: FI-XB30SSL-HF15 JST: BHSR-02VS-1 (2 pin) BHSR-05VS-1 (5 pin) Mating Type: Mating Type: JAE: FI-X30S-H SM02B-BHSS-1-TB (2 pin) SM04(9-E2)B-BHS-1-TB (5 pin) 4.0 Absolute Maximum Ratings Absolute maximum ratings of the module is as following: 4.1 TFT LCD Module (C) Copyright AU Optronics Ver 0.2 12/30 2005 All Rights Reserved. No Reproduction and Redistribution Allowed. M201EW01 V3 Item Symbol Min Max Unit Conditions Logic/LCD Drive VIN -0.3 14 [Volt] Note 1,2 4.2 Backlight Unit Item Symbol Min Max Unit Conditions CCFL Current ICFL - 8 [mA] rms Note 1,2 4.3 Absolute Ratings of Environment Item Symbol Min Max Unit Conditions Operating Humidity HOP 5 90 [%RH] Note o Storage Temperature TST -20 +60 [ C] Note Storage Humidity HST 5 90 [%RH] Note Note 1: With in Ta (25 ℃ ) Note 2: Permanent damage to the device may occur if exceed maximum values Relative Humidity % Twb=39℃ T=40℃,H=90% 100 90 80 T=50℃,H=55% 60 T=60℃,H=39% Storage range Operation range 40 T=65℃,H=29% Storage 20 range 5 0 -20 0 50 60 Temperature ℃ 5.0 Electrical characteristics 5.1 TFT LCD Module 5.1.1 Power Specification Input power specifications are as follows; (C) Copyright AU Optronics Ver 0.2 13/30 2005 All Rights Reserved. No Reproduction and Redistribution Allowed. M201EW01 V3 Symbol Parameter Min Typ Max Units Condition Logic/LCD Drive VDD 10.8 12 13.2 [Volt] ±10% Voltage Vin=12V , All White Pattern, IDD VDD current - 550 650 [mA] at 60Hz Irush LCD Inrush Current - - 2.5 [A] Note Vin=12V , All White Pattern, PDD VDD Power - 6.6 8 [Watt] at 60Hz Allowable Logic/LCD [mV] VDDrp 100 Drive Ripple Voltage p-p Note: Measurement conditions: +5.0V Q3 AO6402 D6 F1 D5 D2 S VCC D1 R1 (LCD Module Input) 47K C1 1uF/16V (High to Low) Q3 Control Signal R2 AO6402 G SW 1K C3 +12.0V VR1 0.01uF/25V 47K C2 1uF/25V 5.0V 90% 10% 0V 470 us Vin rising time 5.1.2 Signal Electrical Characteristics Input signals shall be low or Hi-Z state when Vin is off It is recommended to refer the specifications of SN75LVDS82DGG (Texas Instruments) in detail. Each signal characteristics are as follows; Symbol Parameter Min Typ Max Units Condition (C) Copyright AU Optronics Ver 0.2 14/30 2005 All Rights Reserved. No Reproduction and Redistribution Allowed. D1 S D2 D5 D6 G M201EW01 V3 Differential Input High VICM = 1.2V VTH - - +100 [mV] Threshold Note Differential Input Low VICM = 1.2V VTL -100 - - [mV] Threshold Note │VID│ Input Differential Voltage 100 400 600 [mV] Note Differential Input Common VTH/VTL = ±100MV VICM +1.0 +1.2 +1.5 [V] Mode Voltage Note Note: LVDS Signal Waveform VTH │VID│ VTL VICM VSS 5.2 Backlight Unit Parameter guideline for CCFL Inverter Symbol Parameter Min. Typ. Max. Unit Condition [mA] o ISCFL CCFL standard current 6.5 7.0 7.5 (Ta=25 C) Note 1 rms (C) Copyright AU Optronics Ver 0.2 15/30 2005 All Rights Reserved. No Reproduction and Redistribution Allowed. M201EW01 V3 [mA] o 3.0 7.0 8.0 IRCFL CCFL operation range (Ta=25 C) rms o FCFL CCFL Frequency 40 55 80 [KHz] (Ta=25 C) Note 2 CCFL Ignition Voltage ViCFL [Volt] o (End of the lamp wire 2120 - (Ta=0 C) Note 3 o (0 C) rms connector) CCFL Ignition Voltage ViCF [Volt] o (End of the lamp wire 1625 - (Ta=25 C) Note 3 o (25 C) rms connector) CCFL Operation Voltage 750 783 936 [Volt] o VCFL (Ta=25 C) Note 4 @8mA @7mA @3mA rms CCFL Power consumption (for o PCFL - 32.9 - [Watt] (Ta=25 C) Note 5 reference) o LTCFL CCFL life Time 40,000 50,000 - [Hour] (Ta=25 C) Note 6 Note 1: CCFL standard current is measured at 25 ±2℃. Note 2: CCFL Frequency should be carefully determined to avoid interference between inverter and TFT LCD Note 3: ViCFL means Ignition Voltage for both ends of the lamp, and CCFL inverter should be able to give out a power that has a generating capacity of over ViCFL for ignition Note 4: CCFL operation voltage is measured at 25 ±2℃. Note 5: The variance of CCFL power consumption is ±10%. Power is calculated for reference (ICFL×VCFL×6=PCFL). Note 6: Definition of life: brightness becomes 50% or less than the minimum luminance value of CCFL..The typical life time of CCFL is on the condition at 6.0 mA lamp current. 6.0 Signal Characteristic 6.1 Pixel Format Image Following figure shows the relationship of the input signals and LCD pixel format. (C) Copyright AU Optronics Ver 0.2 16/30 2005 All Rights Reserved. No Reproduction and Redistribution Allowed. M201EW01 V3 1 2 1679 1680 R G B R G B R G B R G B 1st Line R G B R G B R G B R G B 1050 Line 6.2 The input data format Note 1: R/G/B data 7:MSB, R/G/B data 0:LSB O = “First Pixel Data” E = “Second Pixel Data” 6.3 Signal Description The module using one LVDS receiver SN75LVDS82(Texas Instruments) or compatible. LVDS is a differential signal technology for LCD interface and high speed data transfer device. Transmitter shall be (C) Copyright AU Optronics Ver 0.2 17/30 2005 All Rights Reserved. No Reproduction and Redistribution Allowed. M201EW01 V3 SN75LVDS83(negative edge sampling) or compatible . The first LVDS port(RxOxxx) transmits odd pixels while the second LVDS port(RxExxx) transmits even pixels. PIN # SIGNAL NAME DESCRIPTION 1 RxO0- Negative LVDS differential data input (Odd data) 2 RxO0+ Positive LVDS differential data input (Odd data) 3 RxO1- Negative LVDS differential data input (Odd data) 4 RxO1+ Positive LVDS differential data input (Odd data) 5 RxO2- Negative LVDS differential data input (Odd data, H-Sync,V-Sync,DSPTMG) 6 RxO2+ Positive LVDS differential data input (Odd data, H-Sync,V-Sync,DSPTMG) 7 GND Power Ground 8 RxOC- Negative LVDS differential clock input (Odd clock) 9 RxOC+ Positive LVDS differential clock input (Odd clock) 10 RxO3- Negative LVDS differential data input (Odd data) 11 RxO3+ Positive LVDS differential data input (Odd data) 12 RxE0- Negative LVDS differential data input (Even clock) 13 RxE0+ Positive LVDS differential data input (Even data) 14 GND Power Ground 15 RxE1- Positive LVDS differential data input (Even data) 16 RxE1+ Negative LVDS differential data input (Even data) 17 GND Power Ground 18 RxE2- Negative LVDS differential data input (Even data) 19 RxE2+ Positive LVDS differential data input (Even data) 20 RxEC- Negative LVDS differential clock input (Even clock) 21 RxEC+ Positive LVDS differential clock input (Even clock) 22 RxE3- Negative LVDS differential data input (Even data) 23 RxE3+ Positive LVDS differential data input (Even data) 24 GND Power Ground 25 NC No contact (For AUO test only) 26 NC No contact (For AUO test only) 27 NC No contact (For AUO test only) 28 POWER Power 29 POWER Power 30 POWER Power Note1: Start from left side (C) Copyright AU Optronics Ver 0.2 18/30 2005 All Rights Reserved. No Reproduction and Redistribution Allowed. Vsync Hsync Tfp(v) E N RGB Data Line VCC CLK RxOIN0- HsyncD PWhs DE RGB Data (Odd) RGB Data (Even) M201EW01 V3 Connector 30 1 Note2: Input signals of odd and even clock shall be the same timing. 6.4 Timing Characteristics Basically, interface timings described here is not actual input timing of LCD module but output timing of SN75LVDS82DGG (Texas Instruments) or equivalent. Signal Item Symbol Min Typ Max Unit Period Tv 1061 1087 1600 Th Vertical Active Tdisp(v) 1050 1050 1050 Th Section Blanking Tbp(v)+Tfp(v)+PWvs 11 37 550 Th Period Th 920 1128 1400 Tclk Horizontal Active Tdisp(h) 840 840 840 Tclk Section Blanking Tbp(h)+Tfp(h)+PWhs 80 288 560 Tclk Period Tclk 12.3 13.6 16.67 ns Clock Frequency Freq 60 73.5 81 MHz Frame rate Frame rate F 55 60 75 Hz Note : DE mode only 6.4.1 Timing diagram (C) Copyright AU Optronics Ver 0.2 19/30 2005 All Rights Reserved. No Reproduction and Redistribution Allowed. M201EW01 V3 6.5 Power ON/OFF Sequence (C) Copyright AU Optronics Ver 0.2 20/30 2005 All Rights Reserved. No Reproduction and Redistribution Allowed. M201EW01 V3 Vin power and lamp on/off sequence is as follows. Interface signals are also shown in the chart. Signals from any system shall be Hi-Z state or low level when Vin is off. 9 9 90 0 0%%% 90% 90% 90% 1 1 10% 0% 0% V V Vi i innn 1 1 10% 0% 0% 10% 10% 10% 0V 0V 0V T T T222 T T T555 T T T666 T7 T7 T7 T1 T1 T1 S S Si i ign gn gnal al al 0V 0V 0V T4 T4 T4 T3 T3 T3 L L La a amp mp mp 0V 0V 0V Values Symbol Unit Min Typ Max T1 0.5 - 10 [ms] T2 0.5 40 50 [ms] T3 200 - - [ms] T4 200 - - [ms] T5 0.5 16 50 [ms] T6 - - 10 [ms] T7 1000 - - [ms] 7.0 Connector & Pin Assignment Physical interface is described as for the connector on module. These connectors are capable of accommodating the following signals and will be following components. (C) Copyright AU Optronics Ver 0.2 21/30 2005 All Rights Reserved. No Reproduction and Redistribution Allowed. M201EW01 V3 7.1 TFT LCD Module Connector Name / Designation Interface Connector / Interface card Manufacturer JAE or compatible Type Part Number FI-XB30SSL-HF15 Mating Housing Part Number JAE: FI-X30S-H Pin# Signal Name Pin# Signal Name 1 RxO0- 2 RxO0+ 3 RxO1- 4 RxO1+ 5 RxO2- 6 RxO2+ 7 GND 8 RxOC- 9 RxOC+ 10 RxO3- 11 RxO3+ 12 RxE0- 13 RxE0+ 14 GND 15 RxE1- 16 RxE1+ 17 GND 18 RxE2- 19 RxE2+ 20 RxEC- 21 RxEC+ 22 RxE3- 23 RxE3+ 24 GND 25 NC 26 NC 27 NC 28 Power 29 Power 30 Power 7.2 Backlight Unit Connector Name / Designation Lamp Connector / Backlight lamp (C) Copyright AU Optronics Ver 0.2 22/30 2005 All Rights Reserved. No Reproduction and Redistribution Allowed. M201EW01 V3 Manufacturer JST BHSR-02VS-1 (CN3/CN4) Type Part Number BHSR-05VS-1 (CN2/CN5) SM02B-BHSS-1-TB (2pin) Mating Type Part Number SM04 (9-E2) B-BHS-1-TB (5pin) 7.3 Signal for Lamp connector Connector No. Pin No. Color Function 1 Pink High Voltage (Lamp 1) 2 Sky Blue High Voltage (Lamp 2) 3 NC NC CN2 4 Black Low Voltage (Lamp 1) Upper 5 Dark Blue Low Voltage (Lamp 2) 1 White High Voltage (Lamp 3) CN3 2 White Low Voltage (Lamp 3) 1 White High Voltage (Lamp 4) CN4 2 White Low Voltage (Lamp 4) 1 Pink High Voltage (Lamp 6) 2 Sky Blue High Voltage (Lamp 5) Lower 3 NC NC CN5 4 Black Low Voltage (Lamp 6) 5 Dark Blue Low Voltage (Lamp 5) Upper (C) Copyright AU Optronics Ver 0.2 23/30 2005 All Rights Reserved. No Reproduction and Redistribution Allowed. Lamp 1 M201EW01 V3 8.0 Reliability Reliability test condition No Test Item Test Condition (C) Copyright AU Optronics Ver 0.2 24/30 2005 All Rights Reserved. No Reproduction and Redistribution Allowed. M201EW01 V3 50℃, 80%, 300hours 1 Temperature Humidity Bias (THB) 50℃, 300hours 2 High Temperature Operation (HTO) 0℃, 300hours 3 Low Temperature Operation (LTO) 60℃, 300hours 4 High Temperature Storage (HTS) -20℃, 300hours 5 Low Temperature Storage (LTS) -20℃/30min, 60℃/30min, 100 cycles 6 Thermal Shock Test (TST) 7 On/Off Test On/10sec, Off/10sec, 30,000 cycles 8 Shock Test (Non-Operating) 50G, 20ms, Half-sine wave (+ X, +Y, +Z) 9 Vibration Test (Non-Operating) 1.5G(10~200Hz P- P), 30 Minutes each Axis (X, Y, Z) Package test: The drop height is 60cm. 10 Drop test 11 ESD (ElectroStatic Discharge) Contact Discharge: ± 8KV, 150pF(330 Ω ) 1sec, 8 points, 25 times/ point Air Discharge: ± 15KV, 150pF(330 Ω ) 1sec, 8 points, 25 times/ point 12 Altitude Test Operation:10,000 ft Non-Operation:30,000 ft 9.0 Environment The display module will meet the provision of this specification during operating condition or after storage (C) Copyright AU Optronics Ver 0.2 25/30 2005 All Rights Reserved. No Reproduction and Redistribution Allowed. M201EW01 V3 or shipment condition specified below. Operation at 10% beyond the specified range will not cause physical damage to the unit. 9.1 Temperature and Humidity 9.1.1 Operating Conditions The display module operates error free, when operated under the following conditions; 0 0 Temperature 0 C to 50 C Relative Humidity 5% to 90% 0 Wet Bulb Temperature 39.0 C 9.1.2 Shipping Conditions The display module operates error free, after the following conditions; 0 0 Temperature -20 C to 60 C Relative Humidity 5% to 90% 0 Wet Bulb Temperature 39.0 C 9.2 Atmospheric Pressure The display assembly is capable of being operated without affecting its operations over the pressure range as following specified; Pressure Note Maximum Pressure 1040hPa 0m = sea level Minimum Pressure 674hPa 3048m = 10.000 feet Note : Non-operation attitude limit of this display module = 30,000 feet. = 9145 m. 10.0 Safety 10.1 Sharp Edge Requirements (C) Copyright AU Optronics Ver 0.2 26/30 2005 All Rights Reserved. No Reproduction and Redistribution Allowed. M201EW01 V3 There will be no sharp edges or comers on the display assembly that could cause injury. 10.2 Materials 10.2.1 Toxicity There will be no carcinogenic materials used anywhere in the display module. If toxic materials are used, they will be reviewed and approved by the responsible ADT Toxicologist. 10.2.2 Flammability All components including electrical components that do not meet the flammability grade UL94-V1 in the module will complete the flammability rating exception approval process. The printed circuit board will be made from material rated 94-V1 or better. The actual UL flammability rating will be printed on the printed circuit board. 10.3 Capacitors If any polarized capacitors are used in the display assembly, provisions will be made to keep them from being inserted backwards. 11.0 Other requirement 11.1 National Test Lab Requirement (C) Copyright AU Optronics Ver 0.2 27/30 2005 All Rights Reserved. No Reproduction and Redistribution Allowed. M201EW01 V3 The display module will satisfy all requirements for compliance to UL 1950, First Edition U.S.A. Information Technology Equipment CSA C22.2 No.950-M89 Canada, Information Technology Equipment EEC 950 International, Information Technology Equipment EN 60 950 International, Information Processing Equipment (European Norm for IEC950) 11.2 Label The label is on the panel as shown below: M201EW01 V.3 M201EW01 V.3 (C) Copyright AU Optronics Ver 0.2 28/30 2005 All Rights Reserved. No Reproduction and Redistribution Allowed. 12.0 Mechanical Characteristics Ver0.2 29/32 Ver0.2 30/32