Total Power: 70-120 Watts Input Voltage: 85-264 VAC 70-120 Watts # of Outputs: Quad NTQ123 Series Electrical Specs Input Input range 85-264 VAC Frequency 47-63 Hz Inrush current 38 A max., cold start @ 25°C Efficiency 65% typical at full load EMI filter FCC Class B conducted and radiated, CISPR 22 Class B conducted and radiated, EN55022 Class B conducted and radiated, VDE 0878 PT3 Class B conducted and radiated. Power factor 0.99 typical Safety ground leakage current <1 mA @ 50/60 Hz, 264 VAC input Output Special Features Maximum power 70 W convection, 120 W with 30 CFM forced air • Active power factor correction Adjustment range ±5% minimum on outputs one and two • EN61000-3-2 compliance Hold-up time 20 ms @ 120 W load, 120 VAC input • Remote sense on outputs one and two Overload protection Short circuit protection on all outputs. • Power fail and remote inhibit Case overload protected @ 110-145% • Single wire current sharing on outputs one above peak rating and two Overvoltage protection 3.3 V and 5 V output: 20% to 35% • Adjustable main outputs above nominal output • Built-in Class B EMI filter Logic Control • Overvoltage protection Power failure TTL logic signal goes high 100-500 • Overload protection msec after 5 V output; it goes low at • Thermal overload protection least 4 msec before loss of regulation Remote inhibit Requires an external TTL Signal to inhibit outputs Remote sense Compensates for 0.5 V lead drop Environmental minimum, will operate without remote sense connected. Reverse connection Operating temperature: 0° to 50°C ambient; derate protection. each output at 2.5% per degree from 50° to 70°C Electromagnetic susceptibility: Designed to meet EN61000-4, -2, -3, -4, -5, -6, -8, -11 Level 3 Humidity: Operating; non-condensing 5% to 95% Vibration: Three orthogonal axes, sweep at 1 oct/min, 5 min. dwell at four major resonances 0.7 G peak 5 Hz to 500 Hz, operational Safety Storage temperature: -40° to 85°C Temperature coefficient: ± .04% per °C VDE 0805/EN60950 (IEC950) 21310-3336-0004 UL UL1950 E186249 MTBF demonstrated: >1 million hours at full load CSA CSA 22.2-234 Level 3 LR109492C and 25°C ambient conditions NEMKO EN 60950/EMKO-TUE P98100870 (74-sec) 203 BABT EN60950/EN41003 608497 CB Certificate and report 5009 CE Mark (LVD) Technical Support: (888) 41-ASTEC or (407) 241-2752 rev 10.19.04 Americas: (760) 930-4600 Europe (UK) 44 (1384) 842-211 Asia (HK) 852-2437-9662 106 NTQ123 Series ASIA EUROPE AMERICAS Units 2111-2116, Level 21 Astec House, Waterfront Business Park 5810 Van Allen Way Tower1, Metroplaza Merry Hill, Dudley Carlsbad, CA 92008 223, Hing Fong Road West Midlands, DY5 1LX, UK Telephone: 760-930-4600 Kwai Fong, New Territories Telephone: 44 (1384) 842-211 Facsimile: 760-930-0698 Hong Kong Facsimile: 44 (1384) 843-355 Telephone: 852-2437-9662 Facsimile: 852-2402-4426 Ordering Information 2 Model Output Minimum Maximum Load with Maximum Load with Peak Regulation Ripple 4 1 3 Number Voltage Load Convection Cooling 30 CFM Forced Air Load P/P (PARD) NTQ123 +3.3 V 0 A 14 A 25 A 28 A ±2% 50 mV +5 V 2 A 12.5 A 24 A 28 A ±2% 50 mV +12 V 0 A 1 A 2 A 4 A ±3% 120 mV -12 V 0 A 0.5 A 1 A 1.5 A ±3% 120 mV 1. Peak current lasting <30 seconds with a maximum 10% duty cycle. 2. At 25°C including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings. 3. Peak-to-peak with 20 MHz bandwidth and 10 μF in parallel with a 0.1 μF capacitor at rated line voltage and load ranges. 4. Minimum loads are required. In parallel minimum loads are 2.5 A on the 5 V output and 1 A on the 3.3 V output for each power supply. Pin Assignments Connector SK1 PIN 1 Ground PIN 3 Neutral PIN 5 Live SK5 PIN 1 +12 V PIN 2 Common PIN 3 -12 V SK6 PIN 1 3.3 V SWP PIN 2 -3.3 V Sense PIN 3 +3.3 V + Sense PIN 4 5 V SWP PIN 5 COMMON PIN 6 +5 V Sense PIN 7 -5 V Sense PIN 8 + Inhibit PIN 9 - Inhibit PIN 10 Power Fail Mating Connectors (SK1) AC Input: Molex: 09-50-8051 (USA) Molex: 09-91-0500 (UK) PINS: 08-58-0111 SK2,3,4: Molex series 19141-0058/0063 (SK5) ±12V Molex:09-50-8031 (USA) Molex: 09-91-0300 (UK) PINS: 08-58-0111 (SK6) Control Signals: Molex: 90142-0010 PINS: 90119-2110 or Amp: 87977-3 PINS: 87309-8 Astec Connector Kit #70-841-012 Notes: 1. Specifications subject to change without notice. 2. All dimensions in inches (mm), tolerance ±.02”. 3. Remote inhibit requires an external 5 V @ 10 mA to activate 4. Mounting maximum insertion depth is 0.12”. 5. Warranty: 1 year 6. Weight: 1.38 lb. / .63 kg www.astecpower.com 107 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Emerson Network Power :   NTQ123  NTQ123-DC  70-841-012