Total Power: 80-110 Watts Input Voltage: 85-264 VAC 110 Watts 120-300 VDC # of Outputs: Quad LPQ110 Series Electrical Specs Input Input range 85-264 VAC 120-300 VDC Frequency 47-440 Hz Inrush current <18 A peak @ 115 VAC; <36 A peak @ 230 VAC, cold start @ 25°C Input current 2.5 A max. (RMS) @ 115 VAC Efficiency 70% typical at full load EMI filter FCC Class B conducted CISPR 22 Class B conducted EN55022 Class B conducted VDE 0878 PT3 Class B conducted Safety ground leakage current <0.5 mA @ 50/60 Hz, 264 VAC input Special Features Output • Universal input Maximum power 80 W for convection; • High efficiency 110 W with 30 CFM forced air • Remote sense on main output Adjustment range ±5% min. on main; 5-25 V on 4th • Built-in EMI filter output on LPQ112 and LPQ113 • Low output ripple Cross regulation ±2% on output 1; ±3% on outputs • Adjustable 5 V output 2, 3 & 4 • Overvoltage protection Hold-up time 20 ms @ 80 W load, 115 VAC • Overload protection nominal line • Adjustable floating 4th output Overload protection Short circuit protection on all (On LPQ112 and LPQ113) outputs. Case overload protected @ •Power fail 110-145% above peak rating • Optional L bracket (-B suffix) Overvoltage protection 5.7-6.7 VDC on main output. • Cover kit available LPX110-C Latching type, recycle AC to reset. Logic Control Environmental Power Failure TTL logic signal goes high 50-150 msec after 5 V output. It goes low at least 4 msec before loss of regulation. Operating temperature: 0° to 50°C ambient Remote sense Compensates for 0.5 V lead drop derate each output at 2.5% per degree from 50° min. Will operate without remote to 70°C sense connected. Reverse Electromagnetic susceptibility: Designed to connection protected. meet IEC 801, -2, -3, -4, -5, -6, Level 3 Humidity: Operating; non-condensing 5% to 95% Electrical Specs Vibration: Three orthogonal axes, sweep at 1 oct/min, 5 min. dwell at four major resonances 0.75 G peak 5 Hz to 500 Hz, operational VDE 0805/EN60950 (IEC950) 11774-3336-1245 (LC #84997) Storage temperature: -40° to 85°C UL UL1950 E132002 CSA CSA 22.2-234 Level 3 LR53982C Temperature coefficient: ±.04% per °C NEMKO EN 60950/EMKO-TUE P94102464 MTBF demonstrated: >550,000 hours at full load (74-sec) 203 and 25°C ambient conditions CB Certificate and report 1423, 1424, 1425 CE Mark (LVD) rev 12.10.03 Technical Support: (888) 41-ASTEC or (407) 241-2752 Americas: (760) 930-4600 Europe (UK) 44 (1384) 842-211 Asia (HK) 852-2437-9662 102 LPQ110 Series 5V O/P ADJ ASIA EUROPE AMERICAS Units 2111-2116, Level 21 Astec House, Waterfront Business Park 5810 Van Allen Way Tower1, Metroplaza Merry Hill, Dudley Carlsbad, CA 92008 223, Hing Fong Road West Midlands, DY5 1LX, UK Telephone: 760-930-4600 Fwai Fong, New Territories Telephone: 44 (1384) 842-211 Facsimile: 760-930-0698 Hong Kong Facsimile: 44 (1384) 843-355 Telephone: 852-2437-9662 Facsimile: 852-2402-4426 Ordering Information Model Output Minimum Maximum Load with Maximum Load with Peak Regulation2 Ripple Number Voltage Load Convection Cooling 30 CFM Forced Air Load1 P/P (PARD)3 LPQ112 5 V 2 A 9 A 11 A 15 A ±2% 50 mV 12 V 0 A 4.5 A 5 A 9 A ±3% 120 mV -12 V 0 A 0.7 A 1.0 A 1.5 A ±5% 120 mV ±5-25 V 0 A 2.5 A 3 A 3.5 A ±3% 240 mV, max. LPQ113 5 V 2 A 9 A 11 A 15 A ±2% 50 mV 15 V 0 A 4.5 A 5 A 9 A ±3% 150 mV -15 V 0 A 0.7 A 1.0 A 1.5 A ±5% 150 mV ±5-25 V 0 A 2.5 A 3 A 3.5 A ±3% 240 mV, max. LPQ114 5 V 2A 9 A 11 A 15 A ±2% 50 mV 12 V 0 A 4.5 A 5 A 9 A ±3% 120 mV -12 V 0 A 0.7 A 1.0 A 1.5 A ±5% 120 mV 24 V 0.5 A 3.5 A 4.5 A 5 A +10 / -5% 240 mV 1. Peak current lasting <30 seconds with a maximum 10% duty cycle. 2. At 25°C including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings. 3. Peak-to-peak with 20 MHz bandwidth and 10 µF in parallel with a 0.1 µF capacitor at rated line voltage and load ranges. 4. 4th O/P adjustable 5 to 25 V, factory set at 5 V. 5. Minimum loads are required. Note: -B suffix added to model number indicates L bracket option. -B Bracket Pin Assignments #6-32 PEM 4.28" 6 places (108.6) Connector LPQ112 LPQ113 LPQ114 2.5" (63.5) SK1-1 GND GND GND  SK1-3 Neutral Neutral Neutral SK1-5 Line Line Line  SK2-1 +5 V +5 V +5 V SK2-2 +5 V +5 V +5 V 6.4" (162.6) SK2-3 +5 V +5 V +5 V 7.3" SK2-4 Common Common Common (185.5) SK2-5 Common Common Common SK2-6 Common Common Common SK2-7 Common Common Common SK2-8 +12 V +15 V +12 V SK2-9 +12 V +15 V +12 V 2.2" SK2-10 -12 V -15 V -12 V (56) SK2-11 +5-25 V +5-25 V +24 V 0.86" (21.8) SK2-12 -5-25 V -5-25 V Common SK201-1 +sense +sense +sense 5.9" SK201-2 -sense -sense -sense (150.0) SK202-1 POK POK POK SK202-2 GND GND GND 0.25" (6.35) Mating Connectors SK 202 M2 (POK) AC Input: Molex 09-50-8051 (USA) 1 2 SK 201 1 (+S) 1 2 09-91-0500 (UK) (-S) 2 3 4 PINS: 08-58-0111 5 4.0" 6 DC Outputs: Molex 09-50-8121 (USA) (101.6) 7 8 09-91-1200 (UK) 9 3.5" 10 4th O/P ADJ PINS: 08-58-0111 (88.9) 11 12 Remote sense/Power fail: 1 GND Molex 22-01-1022 (USA) 3 N L 22-01-1023 (UK) SK 1 PINS: 08-50-0114 M1 6.5" 0.25" 0.156" (4) Astec Connector Kit #70-841-008, includes all of the above. (165.1) (6.35) 7.0" DIA (4 places) (177.8) Notes: 1. Specifications subject to change without notice. 2. All dimensions in inches (mm), tolerance is ± 0.02” 1.80" 3. Specifications are for convection rating at factory settings unless otherwise stated. (45.7) 4. Mounting holes M1 and M2 should be grounded for EMI purposes. 5. Mounting hole M1 is safety ground connection. 6. L bracket mounting (6-32) maximum insertion depth is .20” (5). 0.12" 7. Warranty: 1 year (3) 8. Weight: 1.25 lb./0.57 kg www.astecpower.com 103 SK 2