NFS110 Series Single and quad output LOW TO MEDIUM POWER AC/DC POWER SUPPLIES 80-110W AC/DC Universal Input Switch Mode Power Supplies 1 • 7.0 x 4.25 x 1.8 inch package • Overvoltage and short circuit protection • 110W with 20CFM • Adjustable outputs • EN55022, EN55011 conducted emissions level B • UL, VDE and CSA safety approvals • CE mark The NFS110 series is a 110W universal input AC/DC power supply on a 7 x 4.25 inch card. The NFS110 series has four single and three quad output models and has proven itself to be highly reliable and versatile product for a wide range of communication and industrial applications, with a very high peak current capability on each output for drive and motor applications. The NFS110 provides 80W of output power with free air convection cooling which can be boosted to 110W with 20CFM of air. Standard features include overvoltage and short circuit protection. The series, with full international safety approval and the CE mark, meets conducted emissions EN55022 level B. The NFS110 series is designed for use in low power data networking, computer, telecom and industrial applications such as servers, thermal printers, storage devices, vending machines and POS equipment. 2 YEAR WARRANTY All specifications are typical at nominal input, full load at 25°C unless otherwise stated SPECIFICATIONS OUTPUT SPECIFICATIONS GENERAL SPECIFICATIONS Voltage adjustability +5.1V output on multi’s ±3.0% Hold-up time 110VAC @ 80W 35ms 5.1V single output ±3.0% 110VAC @ 110W 17ms 12V single output 12V to 14V 230VAC @ 80W 140ms 15V single output 15V to 18V 230VAC @ 110W 100ms 24V single output 24V to 30V Efficiency Multiple outputs 70% typical Line regulation LL to HL, FL ±0.1% max. +5.1V single 70% typical All outputs on all units 12V and 15V singles 72% typical 24V single 75% typical Overshoot/undershoot At turn-on 0% Isolation voltage Input/output 3000VAC Temperature coefficient All outputs ±0.02%/°C Input/chassis 1500VAC Overvoltage protection Multi output 5.1V only 6.25V±0.75V Switching frequency At 100 Watts output 20 to 70kHz 5.1V single 6.25V±0.75V At zero load 100 to 250kHz 12V single 15.75V±1.0V 15V single 22V±1.5V Approvals and VDE0805, EN60950, IEC950 24V single 33V±2.5V standards IEC1010, UL1950 (See Note 12) CSA C22.2 No. 950 Output power limit Primary power Pin max. 160W limited Pout min. 110W Weight Singles 550g (19.4oz) Multiple outputs 600g (21.2oz) Minimum output current (See Note 13) 0A MTBF (See Note 9) MIL-HDBK-217E 125,000 hours Short circuit protection Burst mode operation ENVIRONMENTAL SPECIFICATIONS INPUT SPECIFICATIONS Thermal performance Operating, see curve 0°C to +70°C (See Notes 9, 10) Non-operating –40°C to +85°C Input voltage range 85 to 264VAC 120 to 370VDC 0°C to +50°C, 80W amb. convection cooled Input frequency range 47Hz to 440Hz +50°C to +70°C, Derate 2W/°C amb. convection cooled Input surge current 230VAC 35A 0°C to +50°C, 110W 20CFM forced air Safety ground 110VAC, 50Hz 0.2mA, max. leakage current 230VAC, 50Hz 0.4mA, max. +50°C to +70°C, Derate 20CFM forced air 2.75W/°C Peak, 0°C to +50°C, 110W EMC CHARACTERISTICS max. 60 seconds Conducted emissions EN55022, FCC part 15 Level B Relative humidity Non-condensing 5% to 95% RH Radiated emissions EN55022, FCC part 15 Level A ESD air EN61000-4-2, level 3 Perf. criteria 1 Altitude Operating 10,000 feet max. ESD contact EN61000-4-2, level 4 Perf. criteria 1 Non-operating 40,000 feet max. Surge EN61000-4-5, level 3 Perf. criteria 1 Fast transients EN61000-4-4, level 3 Perf. criteria 1 Vibration (See Note 11) 5Hz to 500Hz 2.4G approx. Radiated immunity EN61000-4-3, level 3 Perf. criteria 2 File Name: NFS110.PDF Rev: 01 Jan 2000 Conducted immunity EN61000-4-6, level 3 Perf. criteria 1 NFS110 Series Single and quad output LOW TO MEDIUM POWER AC/DC POWER SUPPLIES 80-110W AC/DC Universal Input Switch Mode Power Supplies 2 For the most current data and application support visit www.artesyn.com/powergroup/products.htm OUTPUT CURRENTS OUTPUT TOTAL (4) (F) RIPPLE MODEL NUMBERS (5) VOLTAGE REGULATION (1) (2) (3) MAX PEAK FAN +5.1V 8.0A 20.0A 10.0A 50mV ±2.0% NFS110-7601P +12.0V 4.5A 9.0A 5.0A 120mV ±3.0% –12.0V 0.5A 1.5A 1.0A 120mV ±3.0% –5.0V 0.5A 1.5A 1.0A 50mV ±3.0% (6) +5.1V (I ) 8.0A 20.0A 10.0A 50mV ±2.0% NFS110-7602P A (6) +24.0V (I ) 3.5A 4.5A 4.5A 240mV +10/–5.0% B +12.0V 4.5A 9.0A 5.0A 120mV ±3.0% –12.0V 0.5A 1.5A 1.0A 120mV ±3.0% +5.1V 8.0A 20A 10A 50mV ±2.0% NFS110-7604P +15.0V 4.0A 7.5A 5A 150mV ±3.0% –15.0V 0.5A 1.5A 1.0A 150mV ±3.0% –5.0V 0.5A 1.5A 1.0A 50mV ±3.0% (7,8) 5.1V 16.0A 22.0A 20.0A 50mV ±2.0% NFS110-7605 (7,8) 12V 7.0A 9.0A 9.0A 120mV ±2.0% NFS110-7612 (7,8) 15V 5.0A 7.3A 7.3A 150mV ±2.0% NFS110-7615 (7,8) 24V 3.5A 4.5A 4.5A 240mV ±2.0% NFS110-7624 Notes TRANSIENT RESPONSE 1 Convection cooled, 80W maximum. NFS110-7601P +5.1V (7.5A to 10A) 150mV peak, 2 Peak outputs lasting less than 60 seconds with duty cycle less than 10%. 1ms recovery Total peak power must not exceed 110W. +12V (2.5A to 5A) 100mV peak, 3 Forced air, 20CFM at 1 atmosphere, 110W maximum. 0.5ms recovery 4 Figure is peak-to-peak. Output ripple is measured across a 50MHz -12V (0.5A to 1A) 100mV peak, bandwidth using a 12 inch twisted pair terminated with a 47μF capacitor. 0.5ms recovery 5 Total regulation is defined as the static output regulation at 25°C, including -5V (0.5A to 1A) 100mV peak, initial tolerance, line voltage within stated limits and output voltages 0.5ms recovery adjusted to their factory settings. 6 To achieve stated regulation on the 24V output on the NFS110-7602P, the NFS110-7602P +5.1V (7.5A to 10A) 150mV peak, following load condition must be true: I / I ≤ 5, where: A B 1ms recovery I = +5.1V output current, and A +24V (1.5A to 3A) 300mV peak, I = +24V output current B 1ms recovery The +24V output will maintain ±5.0% regulation under the following +12V (2.5A to 5A) 100mV peak, additional condition: I ≤ 5A. A 0.5ms recovery 7 Single output models have floating outputs which may be referenced as -12V (0.5A to 1A) 100mV peak, either positive or negative. Higher voltage supplies may be adjusted over a 0.5ms recovery wide output voltage range, as long as the total output power does not exceed 80 Watts (natural convection) or 110 Watts (forced air). NFS110-7604P +5.1V (7.5A to 10A) 150mV peak, 8 Power fail detect not available on single output models. 1ms recovery 9 Derating curve is application specific for ambient temperatures >50°C, for +15V (2.5A to 5A) 100mV peak, o optimum reliability no part of the heatsink should exceed 90 C and no 0.5ms recovery o semiconductor case temperature should exceed 100 C. -15V (0.5A to 1A) 100mV peak, 10 Caution: Allow a minimum of 1 second after disconnecting the power when 0.5ms recovery making thermal measurements. -5V (0.5A to 1A) 100mV peak, 11 Three orthogonal axes, random vibration, 10 minute test for each axis. 0.5ms recovery 12 This product is only for inclusion by professional installers within other equipment and must not be operated as a stand alone product. NFS110-7605 +5.1V (10A to 20A) 250mV peak, 13 Artesyn Technologies recommends a minimum load of 11W to achieve the 1ms recovery design MTBF. See the derating curve on page 3. NFS110-7612 +12V (4.5A to 9A) 360mV peak, 1ms recovery NFS110-7615 +15V (3.65A to 7.3A) 450mV peak, 1ms recovery NFS110-7624 +24V (2.25A to 4.5A) 720mV peak, 1ms recovery www.artesyn.com File Name: NFS110.PDF Rev: 01 Jan 2000 NFS110 Series Single and quad output LOW TO MEDIUM POWER AC/DC POWER SUPPLIES 80-110W AC/DC Universal Input Switch Mode Power Supplies 3 For the most current data and application support visit www.artesyn.com/powergroup/products.htm AC (J1) mating connector OPTIONAL POWER FAIL DETECT TIMING DIAGRAM Power fail detect signal (Note 8) Molex 09-50-3051 or Molex 09-91-0500 mating connector with 2478 or 50ms≤T1≤200ms equivalent crimp terminals. AC INPUT T2 will vary with line and load T3‡3ms 4.75V 4.75V 5V OUTPUT Pout: 110W DC (J2) mating connector HIGH PFD output is an open collector which 3.5V MIN Molex 09-50-3131 or Molex 09-91-1300 mating connector with 2478 or LOW PFD SIGNAL will sink ≤40mA in the low state. 0-0.4 MAX equivalent crimp terminals. T3 T2 T1 0.475 –0.010 (12.07) DERATING CURVE (See Notes 9, 10) Output Power (Watts) 110W 1.80 (45.72) MAX 1.00 –0.005 20 CFM FORCED AIR COOLING (25.4) 80W 6-32 UNC 0.050 –0.020 1.55 –0.005 3.35 –0.015 (85.09) (4PL) (1.27) (39.37) PIN 1 Voltage Adjust Optional NATURAL 55W J2 Power Fail CONVECTION Detect Circuit 4.250 COOLING–0.020 (Key = Pin 2) 40W (107.95) T1 T1 3.750 –0.005 Pin 1 (95.25) PIN 1 L1 11W 0.156 J1 11W MINIMUM LOAD REQUIRED AT 230VAC DIA. HOLE 0W C6 F1 (4PL) 0°C 10°C 20°C 30°C 40°C 50°C 60°C 70°C 0.250 5A, 250 VAC 6.50 –0.005 (165.1)–0.010 (6.35) 7.00 –0.020 (177.8) 0.250 –0.010 (6.35) ALL DIMENSIONS IN INCHES (mm) PIN CONNECTIONS J1 –7601P –7602P –7604P SINGLES Mechanical Notes Pin 1 AC Ground AC Ground AC Ground AC Ground A Metallic or non-metallic stand-offs (maximum diameter 5.4mm) can be Pin 2 AC Neutral AC Neutral AC Neutral AC Neutral used in all four mounting holes without effecting safety approval. B The ground pad of the mounting hole near J1, allows system grounding Pin 3 AC Line AC Line AC Line AC Line through a metal stand-off to the system chassis. C The heat sink is grounded, and allows system grounding by mechanical J2 connection to the system chassis. D The supply must be mechanically supported using the PCB mounting holes Pin 1 +5.1V +5.1V +5.1V V out and may be additionally supported by the heatsink mounting holes. Pin 2 +5.1V +5.1V +5.1V V E It is always advisable to attach the power supply heat sink to another out thermal dissipator (such as a chassis or finned heatsink etc). The resulting Pin 3 +5.1V +5.1V +5.1V V decrease in heat sink mounted component temperatures will improve out power supply lifetime. Pin 4 Return Return Return Return F A standard L-bracket and cover is available for mounting which contains all screws, connectors and necessary mounting hardware. Two different kits Pin 5 Return Return Return Return are available, order part number ‘NFS110 COVER KIT’ or ‘NFS110C’. Pin 6 Return Return Return Return Pin 7 Return Return Return Return Pin 8 +12V +12V +15V V out Pin 9 +12V +12V +15V V out Pin 10 PFD PFD PFD N/C International Safety Standard Approvals Pin 11 –12V –12V –15V N/C VDE0805/EN60950/IEC950/IEC1010 File No. 10401-3336-1049 Licence No. 2874, 1653 and 1049 Pin 12 Removed for Key UL1950 File No. E136005 Pin 13 –5V +24V –5V N/C CSA C22.2 No. 950 File No. LR41062C N/C = no connection. Data Sheet © Artesyn Technologies® 2002 The information and specifications contained in this data sheet are believed to be correct at time of publication. However, Artesyn Technologies accepts no responsibility for consequences arising from printing errors or inaccuracies. Specifications are subject to change without notice. No rights under any patent accompany the sale of any such product(s) or information contained herein. www.artesyn.com File Name: NFS110.PDF Rev: 01 Jan 2000