Elite.Parts Manufacturers A ANALOG DEVICES ADA4638-1
About product Specifications Features Datasheet FAQ

ANALOG DEVICES ADA4638-1

Description

Analog Devices ADA4638-1 High Voltage, Zero-Drift, Rail-to-Rail Output Precision Amplifier

Part Number

ADA4638-1

Price

Request Quote

Manufacturer

ANALOG DEVICES

Lead Time

Request Quote

Category

PRODUCTS - A

Specifications

-3dB Bandwidth>

2.5MHz

Ib

45pA

Input Noise (nV/rtHz)

66nV/rtHz

Isy per Amplifier

0.85mA

Slew Rate

1.5V/µs

Vcc-Vee

4.5V to 30V

Vos

0.5µV

Features

Datasheet

pdf file

ADA4638-1-1255864865.pdf

872 KiB

Extracted Text

30 V Zero-Drift, Rail-to-Rail Output Precision Amplifier Data Sheet ADA4638-1 FEATURES PIN CONFIGURATIONS ADA4638-1 Single supply operation: 4.5 V to 30 V NC 1 8 NC Dual supply operation: ±2.25 V to ±15 V –IN 2 7 V+ TOP VIEW Low offset voltage: 4 μV maximum (Not to Scale) +IN 3 6 OUT Input offset voltage drift: 0.05 μV/°C maximum V– 4 5 NC High gain: 130 dB minimum High PSRR: 120 dB minimum NOTES 1. NC = NO CONNECT. DO NOT High CMRR: 130 dB minimum CONNECT TO THIS PIN. Input common-mode range includes lower supply rail Figure 1. 8-Lead SOIC Rail-to-rail output ADA4638-1 Low supply current: 0.95 mA maximum NC 1 8NC –IN 2 7V+ APPLICATIONS TOP VIEW (Not to Scale) 6OUT +IN 3 Electronic weigh scale V– 4 5NC Pressure and position sensors Strain gage amplifiers NOTES 1. NC = NO CONNECT. DO NOT CONNECT TO THIS PIN. Medical instrumentation 2. IT IS RECOMMENDED THAT THE EXPOSED PAD BE Thermocouple amplifiers CONNECTED TO V–. Figure 2. 8-Lead LFCSP GENERAL DESCRIPTION The ADA4638-1 is a high voltage, high precision, zero-drift Table 1. Analog Devices, Inc., Zero-Drift Op Amp Portfolio amplifier featuring rail-to-rail output swing. It is guaranteed to Offset Offset operate from 4.5 V to 30 V single supply or ±2.25 V to ±15 V Operating Voltage Voltage Drift dual supplies while consuming less than 0.95 mA of supply Voltage Type Product (μV) Max (μV/°C) Max current at ±5 V. 30 V Single ADA4638-1 4.5 0.08 16 V Single AD8638 9 0.06 With an offset voltage of 4 μV, offset drift less than 0.05 μV/°C, Dual AD8639 9 0.06 no 1/f noise, and input voltage noise of only 1.2 μV p-p (0.1 Hz 5 V Single ADA4528-1 2.5 0.015 to 10 Hz), the ADA4638-1 is suited for high precision applications AD8628 5 0.02 where large error sources cannot be tolerated. Pressure sensors, AD8538 13 0.1 medical equipment, and strain gage amplifiers benefit greatly ADA4051-1 15 0.1 from nearly zero drift over the wide operating temperature range. Many applications can take advantage of the rail-to-rail Dual AD8629 5 0.02 output swing provided by the ADA4638-1 to maximize the signal- AD8539 13 0.1 to-noise ratio (SNR). ADA4051-2 15 0.1 Quad AD8630 5 0.02 The ADA4638-1 is specified for the extended industrial (−40°C to +125°C) temperature range and is available in 8-lead LFCSP (3 mm × 3 mm) and SOIC packages. Rev. 0 Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. rights of third parties that may result from its use. Specifications subject to change without notice. No Tel: 781.329.4700 www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Fax: 781.461.3113 ©2011 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. 10072-001 10072-002 ADA4638-1 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1  Typical Performance Characteristics ..............................................7  Applications....................................................................................... 1  Applications Information .............................................................. 16  Pin Configurations ........................................................................... 1  Differentiation ............................................................................ 16  General Description ......................................................................... 1  Theory of Operation .................................................................. 17  Revision History ............................................................................... 2  Input Protection ......................................................................... 17  Specifications..................................................................................... 3  No Output Phase Reversal ........................................................ 17  Electrical Characteristics—30 V Operation ............................. 3  Noise Considerations................................................................. 18  Electrical Characteristics—10 V Operation ............................. 4  Comparator Operation.............................................................. 18  Electrical Characteristics—5 V Operation................................ 5  Precision Low-Side Current Shunt Sensor.............................. 20  Absolute Maximum Ratings............................................................ 6  Printed Circuit Board Layout ................................................... 20  Thermal Resistance ...................................................................... 6  Outline Dimensions....................................................................... 21  ESD Caution.................................................................................. 6  Ordering Guide .......................................................................... 21  REVISION HISTORY 10/11—Revision 0: Initial Version Rev. 0 | Page 2 of 24 Data Sheet ADA4638-1 SPECIFICATIONS ELECTRICAL CHARACTERISTICS—30 V OPERATION V = 30 V, V = V /2 V, T = 25°C, unless otherwise specified. S CM SY A Table 2. Parameter Symbol Test Conditions/Comments Min Typ Max Unit INPUT CHARACTERISTICS Offset Voltage VOS 0.5 4.5 μV −40°C ≤ T ≤ +125°C; SOIC 12.5 μV A −40°C ≤ T ≤ +125°C; LFCSP 14.5 μV A Offset Voltage Drift ΔVOS/ΔT −40°C ≤ TA ≤ +125°C; SOIC 0.08 μV/°C −40°C ≤ TA ≤ +125°C; LFCSP 0.1 μV/°C Input Bias Current IB 45 90 pA −40°C ≤ T ≤ +125°C 500 pA A Input Offset Current I 25 105 pA OS −40°C ≤ T ≤ +125°C 170 pA A Input Voltage Range 0 27 V Common-Mode Rejection Ratio CMRR VCM = 0 V to 27 V 130 142 dB −40°C ≤ TA ≤ +125°C 130 dB Open-Loop Gain A R = 10 kΩ, V = 1 V to 29 V 140 165 dB VO L O −40°C ≤ T ≤ +125°C 140 dB A Input Resistance, Common Mode RINCM 330 GΩ Input Capacitance, Differential Mode CINDM 4 pF Input Capacitance, Common Mode CINCM 9 pF OUTPUT CHARACTERISTICS Output Voltage High VOH RL = 10 kΩ to VCM 29.90 29.92 V −40°C ≤ TA ≤ +125°C 29.85 V R = 2 kΩ to V 29.50 29.58 V L CM −40°C ≤ T ≤ +125°C 29.35 V A Output Voltage Low V R = 10 kΩ to V 50 60 mV OL L CM −40°C ≤ TA ≤ +125°C 95 mV R = 2 kΩ to V 235 270 mV L CM −40°C ≤ T ≤ +125°C 445 mV A Short-Circuit Current ISC ±38 mA Closed-Loop Output Impedance ZOUT f = 1 MHz, AV = +1 220 Ω POWER SUPPLY Power Supply Rejection Ratio PSRR VS = 4.5 V to 30 V 120 143 dB −40°C ≤ TA ≤ +125°C 120 dB Supply Current/Amplifier I I = 0 mA 0.85 1.05 mA SY O −40°C ≤ T ≤ +125°C 1.25 mA A DYNAMIC PERFORMANCE Slew Rate SR R = 10 kΩ, C = 20 pF, A = +1 1.5 V/μs L L V Overload Recovery Time R = 10 kΩ, C = 20 pF, A = −100 8 μs L L V Settling Time to 0.1% t V = 5 V step, R = 10 kΩ, C = 20 pF, A = −1 4 μs S IN L L V Unity-Gain Crossover UGC VIN = 30 mV p-p, RL = 10 kΩ, CL = 20 pF, AV = +1 1.3 MHz Phase Margin ΦM VIN = 30 mV p-p, RL = 10 kΩ, CL = 20 pF, AV = +1 69 Degrees Gain-Bandwidth Product GBP VIN = 30 mV p-p, RL = 10 kΩ, CL = 20 pF, AV = +100 1.5 MHz −3 dB Closed-Loop Bandwidth f V = 30 mV p-p, R = 10 kΩ, C = 20 pF, A = +1 2.5 MHz −3dB IN L L V NOISE PERFORMANCE Voltage Noise en p-p f = 0.1 Hz to 10 Hz 1.2 μV p-p Voltage Noise Density e f = 1 kHz 66 nV/√Hz n Current Noise Density i f = 1 kHz 0.1 pA/√Hz n Rev. 0 | Page 3 of 24 ADA4638-1 Data Sheet ELECTRICAL CHARACTERISTICS—10 V OPERATION VS = 10 V, VCM = VSY/2 V, TA = 25°C, unless otherwise specified. Table 3. Parameter Symbol Test Conditions/Comments Min Typ Max Unit INPUT CHARACTERISTICS Offset Voltage VOS 0.1 4 μV −40°C ≤ TA ≤ +125°C; SOIC 9 μV −40°C ≤ TA ≤ +125°C; LFCSP 12 μV Offset Voltage Drift ΔV/ΔT −40°C ≤ T ≤ +125°C; SOIC 0.05 μV/°C OS A −40°C ≤ T ≤ +125°C; LFCSP 0.08 μV/°C A Input Bias Current IB 20 50 pA −40°C ≤ TA ≤ +125°C 250 pA Input Offset Current IOS 20 80 pA −40°C ≤ T ≤ +125°C 140 pA A Input Voltage Range 0 7 V Common-Mode Rejection Ratio CMRR V = 0 V to 7 V 130 155 dB CM −40°C ≤ TA ≤ +125°C 130 dB Open-Loop Gain AVO RL = 10 kΩ, VO = 1 V to 9 V 130 160 dB −40°C ≤ TA ≤ +125°C 130 dB Input Resistance, Common Mode R 250 GΩ INCM Input Capacitance, Differential Mode C 4 pF INDM Input Capacitance, Common Mode C 9 pF INCM OUTPUT CHARACTERISTICS Output Voltage High V R = 10 kΩ to V 9.96 9.97 V OH L CM −40°C ≤ TA ≤ +125°C 9.95 V RL = 2 kΩ to VCM 9.85 9.86 V −40°C ≤ TA ≤ +125°C 9.75 V Output Voltage Low V R = 10 kΩ to V 20 25 mV OL L CM −40°C ≤ T ≤ +125°C 40 mV A RL = 2 kΩ to VCM 80 90 mV −40°C ≤ TA ≤ +125°C 145 mV Short-Circuit Current I ±22 mA SC Closed-Loop Output Impedance Z f = 1 MHz, A = +1 300 Ω OUT V POWER SUPPLY Power Supply Rejection Ratio PSRR V = 4.5 V to 30 V 120 143 dB S −40°C ≤ T ≤ +125°C 120 dB A Supply Current/Amplifier ISY IO = 0 mA 0.8 0.95 mA −40°C ≤ TA ≤ +125°C 1.15 mA DYNAMIC PERFORMANCE Slew Rate SR RL = 10 kΩ, CL = 20 pF, AV = +1 1.5 V/μs Overload Recovery Time RL = 10 kΩ, CL = 20 pF, AV = −100 14 μs Settling Time to 0.1% tS VIN = 2 V step, RL = 10 kΩ, CL = 20 pF, AV = −1 3 μs Unity-Gain Crossover UGC V = 30 mV p-p, R = 10 kΩ, C = 20 pF, A = +1 1.1 MHz IN L L V Phase Margin Φ V = 30 mV p-p, R = 10 kΩ, C = 20 pF, A = +1 67 Degrees M IN L L V Gain Bandwidth Product GBP VIN = 30 mV p-p, RL = 10 kΩ, CL = 20 pF, AV = +100 1.4 MHz −3 dB Closed-Loop Bandwidth f−3dB VIN = 30 mV p-p, RL = 10 kΩ, CL = 20 pF, AV = +1 1.9 MHz NOISE PERFORMANCE Voltage Noise en p-p f = 0.1 Hz to 10 Hz 1.2 μV p-p Voltage Noise Density en f = 1 kHz 66 nV/√Hz Current Noise Density in f = 1 kHz 0.1 pA/√Hz Rev. 0 | Page 4 of 24 Data Sheet ADA4638-1 ELECTRICAL CHARACTERISTICS—5 V OPERATION VS = 5 V, VCM = VSY/2 V, TA = 25°C, unless otherwise specified. Table 4. Parameter Symbol Test Conditions/Comments Min Typ Max Unit INPUT CHARACTERISTICS Offset Voltage VOS 1 13 μV −40°C ≤ TA ≤ +125°C; SOIC 18 μV −40°C ≤ TA ≤ +125°C; LFCSP 21 μV Offset Voltage Drift ΔV/ΔT −40°C ≤ T ≤ +125°C; SOIC 0.05 μV/°C OS A −40°C ≤ T ≤ +125°C; LFCSP 0.08 μV/°C A Input Bias Current IB 30 90 pA −40°C ≤ TA ≤ +125°C 230 pA Input Offset Current IOS 60 170 pA −40°C ≤ T ≤ +125°C 200 pA A Input Voltage Range 0 3 V Common-Mode Rejection Ratio CMRR V = 0 V to 3 V 118 140 dB CM −40°C ≤ TA ≤ +125°C 118 dB Open-Loop Gain AVO RL = 10 kΩ, VO = 0.5 V to +4.5 V 125 150 dB −40°C ≤ TA ≤ +125°C 125 dB Input Resistance, Common Mode R 75 GΩ INCM Input Capacitance, Differential Mode C 4 pF INDM Input Capacitance, Common Mode C 9 pF INCM OUTPUT CHARACTERISTICS Output Voltage High V R = 10 kΩ to V 4.98 4.984 V OH L CM −40°C ≤ TA ≤ +125°C 4.97 V RL = 2 kΩ to VCM 4.90 4.92 V −40°C ≤ TA ≤ +125°C 4.87 V Output Voltage Low V R = 10 kΩ to V 7.5 10 mV OL L CM −40°C ≤ T ≤ +125°C 15 mV A R = 2 kΩ to V 37 45 mV L CM −40°C ≤ TA ≤ +125°C 70 mV Short-Circuit Current ISC ±22 mA Closed-Loop Output Impedance ZOUT f = 1 MHz, AV = +1 340 Ω POWER SUPPLY Power Supply Rejection Ratio PSRR VS = 4.5 V to 30 V 120 143 dB −40°C ≤ T ≤ +125°C 120 dB A Supply Current/Amplifier I I = 0 mA 0.8 0.95 mA SY O −40°C ≤ T ≤ +125°C 1.15 mA A DYNAMIC PERFORMANCE Slew Rate SR R = 10 kΩ, C = 20 pF, A = +1 1.5 V/μs L L V Overload Recovery Time R = 10 kΩ, C = 20 pF, A = −100 22 μs L L V Settling Time to 0.1% tS VIN = 1 V step, RL = 10 kΩ, CL = 20 pF, AV = −1 3 μs Unity-Gain Crossover UGC VIN = 20 mV p-p, RL = 10 kΩ, CL = 20 pF, AV = +1 1.0 MHz Phase Margin ΦM VIN = 20 mV p-p, RL = 10 kΩ, CL = 20 pF, AV = +1 64 Degrees Gain Bandwidth Product GBP V = 20 mV p-p, R = 10 kΩ, C = 20 pF, A = +100 1.3 MHz IN L L V −3 dB Closed-Loop Bandwidth f V = 20 mV p-p, R = 10 kΩ, C = 20 pF, A = +1 1.8 MHz −3dB IN L L V NOISE PERFORMANCE Voltage Noise e p-p f = 0.1 Hz to 10 Hz 1.2 μV p-p n Voltage Noise Density e f = 1 kHz 70 nV/√Hz n Current Noise Density in f = 1 kHz 0.015 pA/√Hz Rev. 0 | Page 5 of 24 ADA4638-1 Data Sheet ABSOLUTE MAXIMUM RATINGS THERMAL RESISTANCE Table 5. θ is specified for a device soldered on a 4-layer JEDEC JA Parameter Rating standard board with zero airflow. For LFCSP packages, the Supply Voltage 33 V exposed pad is soldered to the board. 1 Input Voltage ±V SY Input Current ±10 mA Table 6. Thermal Resistance Differential Input Voltage ±VSY Package Type θ θ Unit JA JC Output Short-Circuit Duration to GND Indefinite 8-Lead SOIC 120 45 °C/W Storage Temperature Range −65°C to +150°C 8-Lead LFCSP 75 12 °C/W Operating Temperature Range −40°C to +125°C Junction Temperature Range −65°C to +150°C Lead Temperature (Soldering, 60 sec) 300°C ESD CAUTION 1 Input voltage should always be limited to less than 30 V. Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Rev. 0 | Page 6 of 24 Data Sheet ADA4638-1 TYPICAL PERFORMANCE CHARACTERISTICS TA = 25°C, unless otherwise noted. 12 30 V = ±2.5V V = ±15V SY SY V =V /2 V =V /2 CM SY CM SY 150 UNITS 150 UNITS 10 25 8 20 6 15 4 10 2 5 0 0 OFFSET VOLTAGE (µV) OFFSET VOLTAGE (µV) Figure 3. Input Offset Voltage Distribution Figure 6. Input Offset Voltage Distribution 20 14 V = ±15V 18 V = ±2.5V SY SY 12 V =V /2 V =V /2 CM SY CM SY –40°C < T < +125°C 16 –40°C < T < +125°C A A 140 LFCSP UNITS 140 LFCSP UNITS 10 14 12 8 10 6 8 6 4 4 2 2 0 0 0 0.01 0.02 0.03 0.04 0.05 0.06 0.07 0.08 0 0.01 0.020.030.040.050.060.070.08 TCV (µV/°C) OS TCV (µV/°C) OS Figure 4. Input Offset Voltage Drift Distribution Figure 7. Input Offset Voltage Drift Distribution 30 18 V = ±2.5V SY V =±15V SY V =V /2 16 CM SY V =V /2 –40°C ≤ T ≤ +125°C CM SY 25 A –40°C ≤ T ≤ +125°C A 140 SOIC UNITS 14 140 SOIC UNITS 20 12 10 15 8 10 6 4 5 2 0 0 0 0.010.020.030.040.050.060.070.08 0 0.010.020.030.04 0.050.060.070.08 TCV (µV/°C) TCV (µV/°C) OS OS Figure 8. Input Offset Voltage Drift Distribution Figure 5. Input Offset Voltage Drift Distribution Rev. 0 | Page 7 of 24 NUMBER OF AMPLIFIERS NUMBER OF AMPLIFIERS NUMBER OF AMPLIFIERS –10 –9 –8 –7 –6 –5 –4 –3 –2 –1 0 1 2 3 4 5 6 7 8 9 10 10072-003 10072-004 10072-105 NUMBER OF AMPLIFIERS NUMBER OF AMPLIFIERS NUMBER OF AMPLIFIERS –5.0 –4.5 –4.0 –3.5 –3.0 –2.5 –2.0 –1.5 –1.0 –0.5 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 10072-006 10072-007 10072-108 ADA4638-1 Data Sheet 10 10 V = ±2.5V SY V =±15V 8 8 SY 6 6 4 4 2 2 0 0 –2 –2 –4 –4 –6 –6 –8 –8 –10 –10 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 COMMON-MODE VOLTAGE (V) COMMON-MODE VOLTAGE (V) Figure 9. Input Offset Voltage vs. Common-Mode Voltage Figure 12. Input Offset Voltage vs. Common-Mode Voltage 200 150 V = ±2.5V V = ±15V SY SY 100 150 50 100 0 I – 50 B I – B –50 I + B 0 –100 I + B –50 –150 –100 –200 –250 –150 –50 –25 0 25 50 75 100 125 –50 –25 0 25 50 75 100 125 TEMPERATURE (°C) TEMPERATURE (°C) Figure 10. Input Bias Current vs. Temperature Figure 13. Input Bias Current vs. Temperature 150 150 V = ±2.5V V =±15V SY SY 100 100 50 50 I – B 0 0 I + B I + B –50 –50 I – B –100 –100 –150 –150 0 0.5 1.0 1.5 2.0 2.5 3.0 0 3 6 9 12 1518212427 COMMON-MODE VOLTAGE (V) COMMON-MODE VOLTAGE (V) Figure 11. Input Bias Current vs. Common-Mode Voltage Figure 14. Input Bias Current vs. Common-Mode Voltage Rev. 0 | Page 8 of 24 INPUT BIAS CURRENT (pA) INPUT BIAS CURRENT (pA) OFFSET VOLTAGE (µV) 10072-009 10072-005 10072-010 INPUT BIAS CURRENT (pA) INPUT BIAS CURRENT (pA) OFFSET VOLTAGE (µV) 10072-008 10072-013 10072-012 Data Sheet ADA4638-1 10 100 V = ±2.5V V = ±15V SY SY 1 10 –40°C –40°C 0.1 +25°C +25°C 1 +85°C +85°C +125°C +125°C 0.01 0.1 1m 0.01 0.1m 0.01m 0.001 0.001 0.01 0.1 1 10 100 0.001 0.01 0.1 1 10 100 LOAD CURRENT (mA) LOAD CURRENT (mA) Figure 15. Output Voltage (VOL) to Supply Rail vs. Load Current ) to Supply Rail vs. Load Current Figure 18. Output Voltage (VOL 10 100 V = ±2.5V V = ±15V SY SY 1 10 –40°C 0.1 –40°C +25°C +25°C 1 +85°C +85°C +125°C +125°C 0.01 0.1 1m 0.01 0.1m 0.01m 1m 0.001 0.01 0.1 1 10 100 0.001 0.01 0.1 1 10 100 LOAD CURRENT (mA) LOAD CURRENT (mA) Figure 16. Output Voltage (VOH) to Supply Rail vs. Load Current Figure 19. Output Voltage (VOH) to Supply Rail vs. Load Current 450 70 V = ±15V SY V = ±2.5V SY 400 60 350 50 300 40 250 R = 2kΩ L R = 2kΩ L 200 30 150 20 100 R = 10kΩ L R = 10kΩ L 10 50 R = 100kΩ L R = 100kΩ L 0 0 –50 –25 0 25 50 75 100 125 –50 –25 0 25 50 75 100 125 TEMPERATURE (°C) TEMPERATURE (°C) Figure 20. Output Voltage (VOL) to Supply Rail vs. Temperature Figure 17. Output Voltage (VOL) to Supply Rail vs. Temperature Rev. 0 | Page 9 of 24 OUTPUT VOLTAGE (V ) TO SUPPLY RAIL (mV) OUTPUT VOLTAGE (V ) TO SUPPLY RAIL (V) OUTPUT VOLTAGE (V ) TO SUPPLY RAIL (V) OL OH OL 10072-016 10072-015 10072-011 OUTPUT VOLTAGE (V ) TO SUPPLY RAIL (mV) OUTPUT VOLTAGE (V ) TO SUPPLY RAIL (V) OUTPUT VOLTAGE (V ) TO SUPPLY RAIL (V) OL OL OH 10072-018 10072-019 10072-014 ADA4638-1 Data Sheet 600 120 V = ±15V SY V = ±2.5V SY 100 500 80 400 R = 2kΩ L R = 2kΩ L 60 300 40 200 R = 10kΩ R = 10kΩ L L 20 100 R = 100kΩ R = 100kΩ L L 0 0 –50 –25 0 25 50 75 100 125 –50 –25 0 25 50 75 100 125 TEMPERATURE (°C) TEMPERATURE (°C) Figure 21. Output Voltage (V ) to Supply Rail vs. Temperature Figure 24. Output Voltage (VOH) to Supply Rail vs. Temperature OH 1.2 1.2 1.1 1.0 1.0 0.8 V =±5V SY 0.9 0.6 V =±2.5V V =±15V SY SY 0.8 –40°C +25°C 0.4 +85°C 0.7 +125°C 0.2 0.6 0 0.5 02468 10 12 14 16 18 20 22 24 26 28 30 –50 –25 0 25 50 75 100 125 SUPPLY VOLTAGE (V) TEMPERATURE (°C) Figure 22. Supply Current vs. Supply Voltage Figure 25. Supply Current vs. Temperature 80 135 80 135 V =±2.5V V =±15V SY SY R = 10kΩ R = 10kΩ L L PHASE PHASE 90 60 60 90 40 45 40 45 20pF GAIN 20pF GAIN 200pF 200pF 20 0 20 0 0 –45 0 –45 –20 –90 –20 –90 –40 –135 –40 –135 1k 10k 100k 1M 10M 1k 10k 100k 1M 10M FREQUENCY (Hz) FREQUENCY (Hz) Figure 23. Open-Loop Gain and Phase vs. Frequency Figure 26. Open-Loop Gain and Phase vs. Frequency Rev. 0 | Page 10 of 24 GAIN (dB) SUPPLY CURRENT PER AMPLIFIER (mA) OUTPUT VOLTAGE (V ) TO SUPPLY RAIL (mV) OH 10072-021 10072-017 PHASE (Degrees) 10072-022 GAIN (dB) SUPPLY CURRENT PER AMPLIFIER (mA) OUTPUT VOLTAGE (V ) TO SUPPLY RAIL (mV) OH 10072-024 10072-020 PHASE (Degrees) 10072-025 Data Sheet ADA4638-1 60 60 V =±2.5V V = ±15V SY SY 50 50 R = 10kΩ R = 10kΩ L L A = +100 A = +100 V V 40 40 30 30 A = +10 A = +10 V V 20 20 10 10 A = +1 A = +1 V V 0 0 –10 –10 –20 –20 –30 –30 –40 –40 10 100 1k 10k 100k 1M 10M 10 100 1k 10k 100k 1M 10M FREQUENCY (Hz) FREQUENCY (Hz) Figure 27. Closed-Loop Gain vs. Frequency Figure 30. Closed-Loop Gain vs. Frequency 120 120 V =±2.5V V =±15V SY SY V =V /2 V =V /2 CM SY CM SY 100 100 80 80 60 60 40 40 20 20 0 0 100 1k 10k 100k 1M 10M 100 1k 10k 100k 1M 10M FREQUENCY (Hz) FREQUENCY (Hz) Figure 28. CMRR vs. Frequency Figure 31. CMRR vs. Frequency 140 140 V =±2.5V V =±15V SY SY V =V /2 V =V /2 CM SY CM SY 120 120 100 100 80 80 PSRR+ PSRR+ 60 60 40 40 PSRR– PSRR– 20 20 0 0 –20 –20 100 1k 10k 100k 1M 10M 100 1k 10k 100k 1M 10M FREQUENCY (Hz) FREQUENCY (Hz) Figure 32. PSRR vs. Frequency Figure 29. PSRR vs. Frequency Rev. 0 | Page 11 of 24 CLOSED-LOOP GAIN (dB) PSRR (dB) CMRR (dB) 10072-028 10072-027 10072-023 PSRR (dB) CMRR (dB) CLOSED-LOOP GAIN (dB) 10072-026 10072-030 10072-031 ADA4638-1 Data Sheet 1k 1k V =±2.5V V = ±15V SY SY V =V /2 V =V /2 CM SY CM SY A = +10 A = +10 100 100 V V 10 10 A = +100 A = +100 V V A = +1 V A = +1 V 1 1 0.1 0.1 0.01 0.01 1m 1m 100 1k 10k 100k 1M 10M 100 1k 10k 100k 1M 10M FREQUENCY (Hz) FREQUENCY (Hz) Figure 33. Closed-Loop Output Impedance vs. Frequency Figure 36. Closed-Loop Output Impedance vs. Frequency V = ±2.5V V =±15V SY SY V =1V p-p V =24V p-p IN IN A = +1 A = +1 V V R =10kΩ R =10kΩ L L C =100pF C =100pF L L TIME (1µs/DIV) TIME (10µs/DIV) Figure 37. Large Signal Transient Response Figure 34. Large Signal Transient Response V = ±2.5V V =±15V SY SY V =100mV p-p V =100mV p-p IN IN A = +1 A = +1 V V R =10kΩ R =10kΩ L L C =100pF C =100pF L L TIME (1µs/DIV) TIME (1µs/DIV) Figure 38. Small Signal Transient Response Figure 35. Small Signal Transient Response Rev. 0 | Page 12 of 24 Z (Ω) OUT VOLTAGE (20mV/DIV) VOLTAGE (0.5V/DIV) 10072-034 10072-033 10072-029 Z (Ω) OUT VOLTAGE (20mV/DIV) VOLTAGE (5V/DIV) 10072-036 10072-037 10072-032 Data Sheet ADA4638-1 80 80 V = ±2.5V V = ±15V SY SY 70 70 V = 100mV p-p V =100mV p-p IN IN A = +1 A = +1 V V 60 R =10kΩ 60 R =10kΩ L L 50 50 40 40 OS+ OS+ 30 30 OS– OS– 20 20 10 10 0 0 1 10 100 1000 1 10 100 1000 LOAD CAPACITANCE (pF) LOAD CAPACITANCE (pF) Figure 39. Small Signal Overshoot vs. Load Capacitance Figure 42. Small Signal Overshoot vs. Load Capacitance 0.1 0.5 0 0 –0.1 –0.5 V =±2.5V SY –1.0 20 –0.2 A = –100 V V =100mV p-p IN V =±15V SY R =10kΩ 15 L 3 A = –100 V =100pF C L V =500mV p-p IN R =10kΩ L 10 2 C =100pF L 5 1 0 0 –1 –5 TIME (10µs/DIV) TIME (10µs/DIV) Figure 40. Positive Overload Recovery Figure 43. Positive Overload Recovery 1.0 0.2 0.5 0.1 0 0 –0.5 5 V = ±2.5V SY –0.1 A = –100 V V =100mV p-p 0 IN R =10kΩ L 1 =100pF C L –5 V = ±15V SY 0 A = –100 V V =500mV p-p –10 IN R =10kΩ L –1 C =100pF L –15 –2 –20 TIME (10µs/DIV) –3 TIME (10µs/DIV) Figure 44. Negative Overload Recovery Figure 41. Negative Overload Recovery Rev. 0 | Page 13 of 24 INPUT VOLTAGE (V) INPUT VOLTAGE (V) OVERSHOOT (%) 10072-035 OUTPUT VOLTAGE (V) OUTPUT VOLTAGE (V) 10072-040 10072-039 INPUT VOLTAGE (V) INPUT VOLTAGE (V) OVERSHOOT (%) 10072-038 OUTPUT VOLTAGE (V) OUTPUT VOLTAGE (V) 10072-042 10072-043 ADA4638-1 Data Sheet INPUT INPUT V = ±2.5V V = ±15V SY SY A = –1 A = –1 V V R = 10kΩ R = 10kΩ L L OUTPUT +25mV +5mV OUTPUT –5mV –25mV ERROR BAND ERROR BAND POST GAIN = 5 POST GAIN = 5 TIME (2µs/DIV) TIME (2µs/DIV) Figure 48. Positive Settling Time to 0.1% Figure 45. Positive Settling Time to 0.1% INPUT INPUT V = ±2.5V V = ±15V SY SY A = –1 A = –1 V V R = 10kΩ R = 10kΩ L L OUTPUT +25mV +5mV OUTPUT –5mV –25mV ERROR BAND ERROR BAND POST GAIN = 5 POST GAIN = 5 TIME (2µs/DIV) TIME (2µs/DIV) Figure 46. Negative Settling Time to 0.1% Figure 49. Negative Settling Time to 0.1% 10k 10k V = ±15V SY V = ±2.5V SY V = V /2 CM SY V = V /2 CM SY A = +10 A = +10 V V 1k 1k 100 100 10 10 1 10 100 1k 10k 100k 1 10 100 1k 10k 100k FREQUENCY (Hz) FREQUENCY (Hz) Figure 47. Voltage Noise Density vs. Frequency Figure 50. Voltage Noise Density vs. Frequency Rev. 0 | Page 14 of 24 VOLTAGE (1V/DIV) VOLTAGE NOISE DENSITY (nV/√Hz) VOLTAGE (1V/DIV) 10072-041 10072-049 10072-045 VOLTAGE NOISE DENSITY (nV/√Hz) VOLTAGE (5V/DIV) VOLTAGE (5V/DIV) 10072-044 10072-048 10072-046 Data Sheet ADA4638-1 V = ±2.5V V = ±15V SY SY V =V /2 V =V /2 CM SY CM SY A = +100 A = +100 V V TIME (1s/DIV) TIME (1s/DIV) Figure 54. 0.1 Hz to 10 Hz Noise Figure 51. 0.1 Hz to 10 Hz Noise 100 100 10 10 1 500kHz 1 FILTER 500kHz FILTER 80kHz 80kHz 0.1 0.1 FILTER FILTER V = ±2.5V SY f= 1kHz A = +1 0.01 V 0.01 V = ±15V SY R =10kΩ L f=1kHz A = +1 V R =10kΩ L 0.001 0.001 0.001 0.01 0.1 1 10 0.001 0.01 0.1 1 V (V rms) V (V rms) IN IN Figure 52. THD + N vs. Amplitude Figure 55. THD + N vs. Amplitude 1 1 V = ±15V SY V = 7V rms IN = +1 A V R = 10kΩ L 0.1 0.1 500kHz FILTER 0.01 0.01 80kHz FILTER 500kHz FILTER 0.001 0.001 V = ±2.5V SY V = 0.5V rms IN 80kHz FILTER A = +1 V R = 10kΩ L 0.0001 0.0001 10 100 1k 10k 100k 10 100 1k 10k 100k FREQUENCY (Hz) FREQUENCY (Hz) Figure 53. THD + N vs. Frequency Figure 56. THD + N vs. Frequency Rev. 0 | Page 15 of 24 THD + N (%) THD + N (%) VOLTAGE (0.2µV/DIV) 10072-047 10072-051 10072-052 THD + N (%) THD + N (%) VOLTAGE (0.2µV/DIV) 10072-050 10072-053 10072-054 ADA4638-1 Data Sheet APPLICATIONS INFORMATION The ADA4638-1, with its wide supply voltage range of 4.5 V to DIFFERENTIATION 30 V, is a precision, rail-to-rail output, zero-drift operational Traditionally, zero-drift amplifiers are designed using either the amplifier that features a patented combination of auto-zeroing auto-zeroing or chopping technique. Each technique has its and chopping technique. This unique topology allows the benefits and drawbacks. Auto-zeroing usually results in low ADA4638-1 to maintain its low offset voltage over a wide tempera- noise energy at the auto-zeroing frequency, at the expense of ture range and over its operating lifetime. This amplifier offers higher low frequency noise due to aliasing of wideband noise ultralow input offset voltage of 4.5 μV maximum and an input into the auto-zeroed frequency band. Chopping results in lower offset voltage drift of 80 nV/°C maximum. Offset voltage errors low frequency noise at the expense of larger noise energy at the due to common-mode voltage swings and power supply varia- chopping frequency. The ADA4638-1 uses both auto-zeroing tions are also corrected by the auto-zeroing and chopping tech- and chopping in a patented ping-pong arrangement to obtain nique, resulting in a superb typical CMRR figure of 142 dB and lower low frequency noise together with lower energy at the a PSRR figure of 143 dB at a ±15 V supply voltage. With ultrahigh chopping and auto-zeroing frequencies, maximizing the signal- dc accuracy and no 1/f noise component, the ADA4638-1 is to-noise ratio for the majority of applications. The relatively ideal for high gain amplification of low level signals in dc or low high chopping frequency of 16 kHz and auto-zeroing frequency frequency applications without the risk of excessive output of 8 kHz simplifies filter requirements for a wide, useful voltage errors. bandwidth. Rev. 0 | Page 16 of 24 Data Sheet ADA4638-1 THEORY OF OPERATION Figure 57 shows the ADA4638-1 amplifier block diagram. The Ф1 OUT noninverting and inverting amplifier inputs are +IN and –IN, Ф1 Ф4 A OUT respectively. The transconductance amplifiers, A1 and A2, are Ф3 Ф3 CC the two input gain stages; the A3 and A4 transconductance Ф4 Ф1 +IN Ф4 Ф1 amplifiers are the nulling amplifiers used to correct the offsets –IN Ф3 A3 A1 Ф3 of A1 and A2, and A is the output amplifier. A four-phase OUT C1 C2 Ф4 cycle (φ1 to φ4) controls the switches. In Phase 1 (φ1), A1 is Ф3 auto-zeroed where both the inputs of A1 are connected to +IN. Ф3 Ф2 A1 produces a differential output current of VOS1 × gm1, where Ф1 Ф1 VOS1 is the input offset voltage of A1, and gm1 is the differential Ф2 Ф3 transconductance of A1. The outputs of A1 are then connected Ф2 Ф3 to the inputs and outputs of A3. A3 is designed to have an A4 Ф1 Ф1 A2 C3 C4 equivalent resistance of 1/gm3, where gm3 is the transconduct- Ф2 ance of A3. The amplified version of V , which is V × OS1 OS1 gm1/gm3, is stored on Capacitors C1 and C2. These capacitors, Figure 57. ADA4638-1 Amplifier Block Diagram together with A3, are used to null out the offset of A1 when A1 INPUT PROTECTION amplifies the signal during the φ3 and φ4 phases. The ADA4638-1 has internal ESD protection diodes that are While A1 is being auto-zeroed, A2 (nulled by A4, C3, and C4) connected between the inputs and each supply rail. These diodes is used for signal amplification. The ADA4638-1 differs from protect the input transistors in the event of electrostatic dis- traditional auto-zero amplifiers in that the input offset voltage charge and are reverse-biased during normal operation. However, is also chopped during signal amplification. During φ1, +IN if either input exceeds one of the supply rails, these ESD diodes and −IN are applied to the noninverting and inverting inputs, become forward-biased and large amounts of current begin to respectively, of A2. However, during φ2, both the inputs and flow through them. Without current limiting, this excessive outputs of A2 are inverted, and the input offset voltage of A2 is fault current causes permanent damage to the device. If the chopped. inputs are expected to be subject to overvoltage conditions, The combination of auto-zeroing and chopping offers two major insert a resistor in series with each input to limit the input benefits. First, any residual offset following the auto-zeroing current to 10 mA maximum. However, consider the resistor process is reduced. During φ1, the output offset voltage of A2 is thermal noise effect on the entire circuit. +V and during φ2, it is –V , producing a theoretical OSAZ2 OSAZ2 NO OUTPUT PHASE REVERSAL average of zero. Second, the aliased noise spectrum density at dc due to auto-zeroing is modulated up to the chopping frequency, An undesired phenomenon, phase reversal (also known as phase inversion) occurs in many amplifiers when one or both of and the prechopped noise spectrum density at the chopping the inputs are driven beyond the specified input common-mode frequency is modulated down to dc. This noise transformation voltage range, in effect reversing the polarity of the output. In lowers the noise spectrum density at dc, thus making zero-drift some cases, phase reversal can induce lockups and cause amplifiers ideal for low frequency signal amplification. equipment damage as well as self destruction. During φ3 and φ4, the roles of A1 and A2 are reversed. A2 offset is nulled, and the input signal is chopped and amplified The ADA4638-1 has been carefully designed to prevent any using A1. output phase reversal, provided that both inputs are maintained within the supply voltages. If either one or both inputs may exceed either supply voltage, place resistors in series with the inputs to limit the current to less than 10 mA. The ADA4638-1 features rail-to-rail output with a supply volt- age from 4.5 V to 30 V. Figure 58 shows the input and output waveforms of the ADA4638-1 configured as a unity-gain buffer with a supply voltage of ±15 V and a resistive load of 10 kΩ. The ADA4638-1 does not exhibit phase reversal. Rev. 0 | Page 17 of 24 10072-157 ADA4638-1 Data Sheet V + SY V = ±15V SY R =10kΩ L A1 I + V SY IN V OUT 100kΩ ADA4638-1 V OUT A2 I – 100kΩ SY –V SY TIME (2µs/DIV) Figure 59. Voltage Follower Figure 58. No Phase Reversal 1.0 0.8 NOISE CONSIDERATIONS I + SY 0.6 1/f Noise 0.4 1/f noise, also known as pink noise or flicker noise, is inherent 0.2 in semiconductor devices and increases as frequency decreases. At low frequency, 1/f noise is a major noise contributor and 0 causes a significant output voltage offset when amplified by the –0.2 noise gain of the circuit. However, the ADA4638-1 eliminates –0.4 the 1/f noise internally, thus making it an excellent choice for dc –0.6 or low frequency high precision applications. The 0.1 Hz to I – SY –0.8 10 Hz voltage noise is only 1.2 μV p-p at ±15 V of supply voltage. –1.0 The low frequency 1/f noise appears as a slow varying offset to 0 5 10 15 20 25 30 the ADA4638-1 and is greatly reduced by the combination of V (V) SY auto-zeroing and chopping technique. This allows the ADA4638-1 Figure 60. Supply Current vs. Supply Voltage (Voltage Follower) to have a much lower noise at dc and low frequency in comparison In contrast to op amps, comparators are designed to work in an to standard low noise amplifiers that are susceptible to 1/f noise. open-loop configuration and to drive logic circuits. Although Figure 47 and Figure 50 show the voltage noise density of the op amps are different from comparators, occasionally an unused ADA4638-1 with no 1/f noise. section of a dual op amp is used as a comparator to save board COMPARATOR OPERATION space and cost; however, this is not recommended. Op amps are designed to operate in a closed-loop configuration Figure 61 and Figure 62 show the ADA4638-1 configured as with feedback from its output to its inverting input. Figure 59 a comparator, with resistors R and R in series with the IN1 IN2 shows the ADA4638-1 configured as a voltage follower with an input pins. input voltage, which is kept at midpoint of the power supplies. +V SY A1 and A2 indicate the placement of ammeters to measure supply A3 I + currents. ISY+ refers to the current flowing into the positive TOTAL supply pin of the op amp, and ISY− refers to the current flowing out of the negative supply pin of the op amp. From Figure 60, as I + A1 I + R INPUT SY IN1 expected in normal operating condition, the current flowing into the op amp is equivalent to the current flowing out of the op V OUT amp, where I + = I −. SY SY ADA4638-1 I R INPUT– IN2 A2 I – SY A4 I – TOTAL –V SY Figure 61. Comparator A Rev. 0 | Page 18 of 24 VOLTAGE (10V/DIV) 10072-158 I PER AMPLIFIER (mA) SY 10072-061 10072-059 10072-060 Data Sheet ADA4638-1 +V 1.0 SY 0.8 A1 I + TOTAL 0.6 0.4 I + A3 I + R INPUT SY IN1 0.2 I + TOTAL I + SY 0 I – SY V OUT ADA4638-1 – I TOTAL –0.2 –0.4 I R INPUT– IN2 –0.6 A4 I – SY –0.8 –1.0 A2 I – TOTAL 0 5 10 15 20 25 30 V (V) SY –V SY Figure 64. Supply Current vs. Supply Voltage Figure 62. Comparator B (Comparator B, RIN1 = RIN2 = 100 kΩ) Figure 63 and Figure 64 show the total supply current of the 12 system, ITOTAL, and the actual currents, ISY, that flow into and 10 out of the supply pins of the ADA4638-1. With RIN1 = RIN2 = 8 100 kΩ and supply voltage of 30 V, the total supply current of 6 the system is 800 μA to 900 μA. 4 2 With smaller input series resistors, total supply current of the 0 system increases much more. Figure 65 and Figure 66 show the –2 supply currents with R = R = 0 Ω. The total current of the IN1 IN2 –4 system increases to 10 mA. –6 I + TOTAL ITOTAL = ISY + IINPUT I + SY –8 I – SY I – Note that, at 30 V of supply voltage, 8 mA to 9 mA of current –10 TOTAL flows through the input pins. This is undesirable. The ADA4638-1 –12 0 5 10 15 20 25 30 is not recommended to be used as a comparator. If absolutely V (V) SY necessary, place resistors in series with the inputs of the ampli- Figure 65. Supply Current vs. Supply Voltage fier to limit input current to less than 10 mA. (Comparator A, RIN1 = RIN2 = 0 kΩ) For more details on op amps as comparators, refer to the AN-849 Application Note, Using Op Amps as Comparators. 12 1.0 10 0.8 8 6 0.6 4 0.4 2 0.2 I + TOTAL 0 I + SY 0 –2 – I SY I – TOTAL –0.2 –4 –6 I + –0.4 TOTAL I + SY –8 –0.6 I – SY I – –10 TOTAL –0.8 –12 0 5 10 15 20 25 30 –1.0 0 5 10 15 20 25 30 V (V) SY V (V) SY Figure 66. Supply Current vs. Supply Voltage (Comparator B, R = R = 0 kΩ) Figure 63. Supply Current vs. Supply Voltage IN1 IN2 (Comparator A, R = R = 100 kΩ) IN1 IN2 Rev. 0 | Page 19 of 24 CURRENT (mA) 10072-062 10072-063 CURRENT (mA) CURRENT (mA) CURRENT (mA) 10072-066 10072-065 10072-064 ADA4638-1 Data Sheet To avoid leakage currents, keep the surface of the board clean PRECISION LOW-SIDE CURRENT SHUNT SENSOR and free of moisture. Coating the board surface creates a barrier Many applications require the sensing of signals near the to moisture accumulation and reduces parasitic resistance on positive or negative rails. Current shunt sensors are one such the board. application and are mostly used for feedback control systems. They are also used in a variety of other applications, including Properly bypassing the power supplies and keeping the supply power metering, battery fuel gauging and feedback controls in traces short minimizes power supply disturbances caused by electrical power steering. In such application, it is desirable to output current variation. Connect bypass capacitors as close as possible to the device supply pins. Stray capacitances are a use a shunt with very low resistance to minimize series voltage concern at the outputs and the inputs of the amplifier. It is drop. This not only minimizes wasted power, but also allows the recommended that signal traces be kept at a distance of at least measurement of high currents while saving power. A typical 5 mm from supply lines to minimize coupling. shunt may be 100 mΩ. At a measured current of 1 A, the voltage produced from the shunt is 100 mV, and the amplifier A potential source of offset error is the Seebeck voltage on the error sources are not critical. However, at low measured current circuit board. The Seebeck voltage occurs at the junction of two in the 1 mA range, the 100 μV generated across the shunt dissimilar metals and is a function of the temperature of the demands a very low offset voltage and drift amplifier to junction. The most common metallic junctions on a circuit maintain absolute accuracy. The unique attributes of a zero- board are solder-to-board trace and solder-to-component lead. drift amplifier provides a solution. The ADA4638-1, with its Figure 68 shows a cross section of a surface-mount component input common-mode voltage that includes the lower supply rail, soldered to a PCB. A variation in temperature across the board can be used for implementing low-side current shunt sensors. (where T A1 ≠ TA2) causes a mismatch in the Seebeck voltages at Figure 67 shows a low-side current sensing circuit using the the solder joints thereby resulting in thermal voltage errors that ADA4638-1. The ADA4638-1 is configured as a difference degrade the performance of the ultralow offset voltage of the amplifier with a gain of 1000. Although the ADA4638-1 has ADA4638-1. high common-mode rejection, the CMR of the system is limited COMPONENT LEAD by the external resistors. Therefore, the key to high CMR for the V system are resistors that are well matched from both the V SC2 SOLDER SC1 SURFACE-MOUNT + COMPONENT resistive ratio and relative drift, where R1/R2 = R3/R4. The V V TS1 TS2 + resistors are important in determining the performance over PC BOARD manufacturing tolerances, time, and temperature. T T A1 A2 IF T ≠ T , THEN COPPER A1 A2 I TRACE V + V ≠ V + V TS1 SC1 TS2 SC2 R Figure 68. Mismatch in Seebeck Voltages Causes Seebeck Voltage Error V S R SY I L 0.1Ω To minimize these thermocouple effects, orient resistors so that R2 R1 100kΩ 100Ω heat sources warm both ends equally. Where possible, the input V * OUT signal paths should contain matching numbers and types of V SY components to match the number and type of thermocouple junctions. For example, dummy components, such as zero value ADA4638-1 resistors, can be used to match the thermoelectric error source (real resistors in the opposite input path). Place matching compo- R4 R3 100kΩ 100Ω nents in close proximity and orient them in the same manner to ensure equal Seebeck voltages, thus cancelling thermal errors. *V = AMPLIFIER GAIN × VOLTAGE ACROSS R OUT S Additionally, use leads that are of equal length to keep thermal = 1000 × R × I S = 100 × I conduction in equilibrium. Keep heat sources on the PCB as far Figure 67. Low-Side Current Sensing Circuit away from amplifier input circuitry as is practical. PRINTED CIRCUIT BOARD LAYOUT It is highly recommended to use a ground plane. A ground plane helps distribute heat throughout the board, maintains a constant The ADA4638-1 is a high precision device with ultralow offset temperature across the board, and reduces EMI noise pickup. voltage and offset voltage drift. Therefore, care must be taken in the design of the printed circuit board (PCB) layout to achieve optimum performance of the ADA4638-1 at board level. Rev. 0 | Page 20 of 24 10072-167 10072-067 + + Data Sheet ADA4638-1 OUTLINE DIMENSIONS 2.44 2.34 3.10 2.24 3.00 SQ 2.90 0.50 BSC 8 5 PIN 1 INDEX EXPOSED 1.70 AREA PAD 1.60 1.50 0.50 0.40 0.30 4 1 TOP VIEW BOTTOM VIEW FOR PROPER CONNECTION OF 0.80 THE EXPOSED PAD, REFER TO 0.05 MAX 0.75 THE PIN CONFIGURATION 0.02 NOM 0.70 SECTION OF THIS DATA SHEET. COPLANARITY 0.08 SEATING 0.30 PLANE 0.203 REF 0.25 0.20 COMPLIANT TOJEDEC STANDARDS MO-229-WEED Figure 69. 8-Lead Lead Frame Chip Scale Package [LFCSP_WD] 3 mm × 3 mm Body, Very Very Thin, Dual Lead (CP-8-11) Dimensions shown in millimeters 5.00 (0.1968) 4.80 (0.1890) 85 4.00 (0.1574) 6.20 (0.2441) 1 3.80 (0.1497) 5.80 (0.2284) 4 1.27 (0.0500) 0.50 (0.0196) 45° BSC 1.75 (0.0688) 0.25 (0.0099) 1.35 (0.0532) 0.25 (0.0098) 8° 0.10 (0.0040) 0° COPLANARITY 0.51 (0.0201) 1.27 (0.0500) 0.10 0.31 (0.0122) 0.25 (0.0098) SEATING 0.40 (0.0157) PLANE 0.17 (0.0067) COMPLIANT TO JEDEC STANDARDS MS-012-AA CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN. Figure 70. 8-Lead Standard Small Outline Package [SOIC_N] Narrow Body (R-8) Dimensions shown in millimeters and (inches) ORDERING GUIDE 1 Model Temperature Range Package Description Package Option Branding ADA4638-1ACPZ-R7 −40°C to +125°C 8-Lead Lead Frame Chip Scale Package [LFCSP_WD] CP-8-11 A2W ADA4638-1ACPZ-RL −40°C to +125°C 8-Lead Lead Frame Chip Scale Package [LFCSP_WD] CP-8-11 A2W ADA4638-1ARZ −40°C to +125°C 8-Lead Standard Small Outline Package [SOIC_N] R-8 ADA4638-1ARZ-R7 −40°C to +125°C 8-Lead Standard Small Outline Package [SOIC_N] R-8 ADA4638-1ARZ-RL −40°C to +125°C 8-Lead Standard Small Outline Package [SOIC_N] R-8 1 Z = RoHS Compliant Part. Rev. 0 | Page 21 of 24 PIN 1 INDICATOR (R 0.15) 012407-A 01-24-2011-B ADA4638-1 Data Sheet NOTES Rev. 0 | Page 22 of 24 Data Sheet ADA4638-1 NOTES Rev. 0 | Page 23 of 24 ADA4638-1 Data Sheet NOTES ©2011 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D10072-0-10/11(0) Rev. 0 | Page 24 of 24

Frequently asked questions

What makes Elite.Parts unique?

chervon down
At GID Industrial (Elite.Parts' parent company), we specialize in procuring industrial parts. We know where to find the rare and obsolete equipment that our customers need in order to get back to business. There are other companies who claim to do what we do, but we're confident that our commitment to quality and value is unparalleled in our field.

What kind of warranty will the ADA4638-1 have?

chervon down
Warranties differ by part and by which suppliers we use to procure it for you. Sometimes, a part will be sold as-is and without a warranty. Our specialty, single board computers, tend to receive a one-year warranty.

Which carriers does Elite.Parts work with?

chervon down
Elite.Parts can ship via FedEx, UPS, DHL, and USPS. We have accounts with each of them and generally ship using one of those, but we can also ship using your account if you would prefer. However, we can use other carriers if it will be more convenient for you.

Will Elite.Parts sell to me even though I live outside the USA?

chervon down
Absolutely! We are happy to serve customers regardless of location. We work with international clients all the time, and we are familiar with shipping to destinations all across the globe.

I have a preferred payment method. Will Elite.Parts accept it?

chervon down
All major credit cards are accepted: Visa, MasterCard, Discover, and American Express. We will also accept payment made with wire transfer or PayPal. Checks will only be accepted from customers in the USA. Terms may available for larger orders, upon approval.

Why buy from GID?

quality

Quality

We are industry veterans who take pride in our work

protection

Protection

Avoid the dangers of risky trading in the gray market

access

Access

Our network of suppliers is ready and at your disposal

savings

Savings

Maintain legacy systems to prevent costly downtime

speed

Speed

Time is of the essence, and we are respectful of yours

What they say about us

FANTASTIC RESOURCE

star star star star star

One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!

Bucher Emhart Glass

EXCELLENT SERVICE

star star star star star

With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.

Fuji

HARD TO FIND A BETTER PROVIDER

star star star star star

Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.

Applied Materials

CONSISTENTLY DELIVERS QUALITY SOLUTIONS

star star star star star

Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.

Nidec Vamco

TERRIFIC RESOURCE

star star star star star

This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.

Trican Well Service

GO TO SOURCE

star star star star star

When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.

ConAgra Foods

Related Products

ANALOG DEVICE# A5E1032

SOCKET FOR MODEL AD210 IC

TRANSFORMER CURRENT 60.0 AMP

SOCKET FOR MODEL 1B22 IC

product

Analog Devices AD7291 12-Bit Low power 8-Channel Successive Approximation Analog-to-Digital Converte...