Elite.Parts Manufacturers A ANALOG DEVICES ADA4528-1
About product Specifications Features Datasheet FAQ

ANALOG DEVICES ADA4528-1

Description

Analog Devices ADA4528-1 Precision, Ultra-low Noise, Zero-Drift Operational Amplifier

Part Number

ADA4528-1

Price

Request Quote

Manufacturer

ANALOG DEVICES

Lead Time

Request Quote

Category

PRODUCTS - A

Specifications

-3dB Bandwidth>

4MHz

Ib

90pA

Input Noise (nV/rtHz)

5.3nV/rtHz

Isy per Amplifier

1.4mA

Slew Rate

0.5V/µs

Vcc-Vee

2.2V to 5.5V

Vos

0.3µV

Vos TC

0.0020µV/degC

Features

Datasheet

pdf file

ADA4528-1-1160927381.pdf

760 KiB

Extracted Text

Precision, Ultralow Noise, RRIO, Zero-Drift Op Amp Data Sheet ADA4528-1 FEATURES PIN CONFIGURATIONS Low offset: 2.5 μV maximum NC 1 8 NC ADA4528-1 –IN 2 7 V+ Low offset voltage drift: 0.015 μV/°C maximum TOP VIEW +IN 3 6 OUT Low noise (Not to Scale) V– 4 5 NC 5.6 nV/√Hz at f = 1 kHz, A = +100 V NC = NO CONNECT. DO NOT 97 nV p-p at f = 0.1 Hz to 10 Hz, A = +100 V CONNECT TO THIS PIN. Open-loop voltage gain: 130 dB minimum Figure 1. 8-Lead MSOP CMRR: 135 dB minimum PSRR: 130 dB minimum NC 1 8NC ADA4528-1 Gain bandwidth product: 4 MHz –IN 2 7V+ TOP VIEW Single-supply operation: 2.2 V to 5.5 V +IN 3 6OUT (Not to Scale) Dual-supply operation: ±1.1 V to ±2.75 V V– 4 5NC Rail-to-rail input and output NOTES 1. NC = NO CONNECT. DO NOT CONNECT Unity-gain stable TO THIS PIN. 2. IT IS RECOMMENDED THAT THE EXPOSED PAD BE CONNECTED TO V–. APPLICATIONS Figure 2. 8-Lead LFCSP Thermocouple/thermopile Load cell and bridge transducer Precision instrumentation Electronic scales Medical instrumentation Handheld test equipment 1 GENERAL DESCRIPTION Table 1. Analog Devices, Inc., Zero-Drift Op Amp Portfolio Low 16 V The ADA4528-1 is an ultralow noise, zero-drift operational am- Ultralow Micropower Power Operating plifier featuring rail-to-rail input and output swing. With an Type Noise (<20 μA) (<1 mA) Voltage offset voltage of 2.5 μV, offset voltage drift of 0.015 μV/°C, and Single ADA4528-1 ADA4051-1 AD8628 AD8638 typical noise of 97 nV p-p (0.1 Hz to 10 Hz, AV = +100), the AD8538 ADA4528-1 is well suited for applications in which error sources Dual ADA4051-2 AD8629 AD8639 cannot be tolerated. AD8539 The ADA4528-1 has a wide operating supply range of 2.2 V to Quad AD8630 5.5 V, high gain, and excellent CMRR and PSRR specifications 1 See www.analog.com for a selection of zero-drift operational amplifiers. that make it ideal for precision amplification of low level signals, such as position and pressure sensors, strain gages, and medical instrumentation. The ADA4528-1 is specified over the extended industrial temperature range (−40°C to +125°C) and is available in an 8-lead MSOP and an 8-lead LFCSP package. For more information on the ADA4528-1, refer to AN-1114 Lowest Noise Zero-Drift Amplifier Has 5.6 nV/√Hz Voltage Noise Density. Rev. A Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. rights of third parties that may result from its use. Specifications subject to change without notice. No Tel: 781.329.4700 www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Fax: 781.461.3113 ©2011 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. 09437-001 09437-102 ADA4528-1 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1  ESD Caution...................................................................................5  Applications....................................................................................... 1  Typical Performance Characteristics ..............................................6  Pin Configurations ........................................................................... 1  Applications Information .............................................................. 15  General Description ......................................................................... 1  Input Protection ......................................................................... 15  Revision History ............................................................................... 2  Rail-to-Rail Input and Output.................................................. 15  Specifications..................................................................................... 3  Noise Considerations................................................................. 15  Electrical Characteristics—2.5 V Operation ............................ 3  Printed Circuit Board Layout ................................................... 17  Electrical Characteristics—5 V Operation................................ 4  Outline Dimensions....................................................................... 18  Absolute Maximum Ratings............................................................ 5  Ordering Guide .......................................................................... 18  Thermal Resistance ...................................................................... 5  REVISION HISTORY 9/11—Rev. 0 to Rev. A Added 8-Lead LFCSP_WD Package................................Universal Changes to General Description Section ..................................... 1 Added Figure 2; Renumbered Sequentially .................................. 1 Changes to Offset Voltage, Offset Voltage Drift, Power Supply Rejection Ratio, and Settling Time to 0.1% Parameters, Table 2 ................................................................................................ 3 Changes to Thermal Resistance Section and Table 5................... 5 Changes to Figure 41 and Figure 44............................................. 12 Changes to Figure 45 and Figure 48............................................. 13 Updated Outline Dimensions ....................................................... 18 Changes to Ordering Guide .......................................................... 18 1/11—Revision 0: Initial Version Rev. A | Page 2 of 20 Data Sheet ADA4528-1 SPECIFICATIONS ELECTRICAL CHARACTERISTICS—2.5 V OPERATION V = 2.5 V, V = V /2 V, T = 25°C, unless otherwise specified. S CM SY A Table 2. Parameter Symbol Test Conditions/Comments Min Typ Max Unit INPUT CHARACTERISTICS Offset Voltage VOS VCM = 0 V to 2.5 V 0.3 2.5 μV −40°C ≤ T ≤ +125°C; MSOP package 4 μV A −40°C ≤ TA ≤ +125°C; LFCSP package 4.3 μV Offset Voltage Drift ΔV/ΔT −40°C ≤ T ≤ +125°C; MSOP package 0.002 0.015 μV/°C OS A −40°C ≤ T ≤ +125°C; LFCSP package 0.018 μV/°C A Input Bias Current IB 220 400 pA −40°C ≤ T ≤ +125°C 600 pA A Input Offset Current IOS 440 800 pA −40°C ≤ TA ≤ +125°C 1 nA Input Voltage Range 0 2.5 V Common-Mode Rejection Ratio CMRR VCM = 0 V to 2.5 V 135 158 dB −40°C ≤ T ≤ +125°C 116 dB A Open-Loop Gain AVO RL = 10 kΩ, VO = 0.1 V to 2.4 V 130 140 dB −40°C ≤ TA ≤ +125°C 126 dB R = 2 kΩ, V = 0.1 V to 2.4 V 125 132 dB L O −40°C ≤ TA ≤ +125°C 121 dB Input Resistance, Differential Mode R 225 kΩ INDM Input Resistance, Common Mode R 1 GΩ INCM Input Capacitance, Differential Mode CINDM 15 pF Input Capacitance, Common Mode C 30 pF INCM OUTPUT CHARACTERISTICS Output Voltage High VOH RL = 10 kΩ to VCM 2.49 2.495 V −40°C ≤ TA ≤ +125°C 2.485 V R = 2 kΩ to V 2.46 2.48 V L CM −40°C ≤ TA ≤ +125°C 2.44 V Output Voltage Low V R = 10 kΩ to V 5 10 mV OL L CM −40°C ≤ T ≤ +125°C 15 mV A RL = 2 kΩ to VCM 20 40 mV −40°C ≤ T ≤ +125°C 60 mV A Short-Circuit Current ISC ±30 mA Closed-Loop Output Impedance ZOUT f = 1 kHz, AV = +10 0.1 Ω POWER SUPPLY Power Supply Rejection Ratio PSRR V = 2.2 V to 5.5 V 130 150 dB SY −40°C ≤ TA ≤ +125°C 127 dB Supply Current/Amplifier I I = 0 mA 1.4 1.7 mA SY O −40°C ≤ T ≤ +125°C 2.1 mA A DYNAMIC PERFORMANCE Slew Rate SR RL = 10 kΩ, CL = 100 pF, AV = +1 0.45 V/μs Settling Time to 0.1% t V = 1.5 V step, R = 10 kΩ, C = 100 pF, A = −1 7 μs s IN L L V Gain Bandwidth Product GBP R = 10 kΩ, C = 100 pF, A = +1 4 MHz L L V Phase Margin ΦM RL = 10 kΩ, CL = 100 pF, AV = +1 57 Degrees Overload Recovery Time R = 10 kΩ, C = 100 pF, A = −10 50 μs L L V NOISE PERFORMANCE Voltage Noise e p-p f = 0.1 Hz to 10 Hz, A = +100 97 nV p-p n V Voltage Noise Density en f = 1 kHz, AV = +100 5.6 nV/√Hz f = 1 kHz, A = +100, V = 2.0 V 5.5 nV/√Hz V CM Current Noise in p-p f = 0.1 Hz to 10 Hz, AV = +100 10 pA p-p Current Noise Density i f = 1 kHz, A = +100 0.7 pA/√Hz n V Rev. A | Page 3 of 20 ADA4528-1 Data Sheet ELECTRICAL CHARACTERISTICS—5 V OPERATION VS = 5 V, VCM = VSY/2 V, TA = +25°C, unless otherwise specified. Table 3. Parameter Symbol Test Conditions/Comments Min Typ Max Unit INPUT CHARACTERISTICS Offset Voltage VOS VCM = 0 V to 5 V 0.3 2.5 μV −40°C ≤ TA ≤ +125°C 4 μV Offset Voltage Drift ΔV/ΔT −40°C ≤ T ≤ +125°C 0.002 0.015 μV/°C OS A Input Bias Current I 90 200 pA B −40°C ≤ T ≤ +125°C 300 pA A Input Offset Current IOS 180 400 pA −40°C ≤ TA ≤ +125°C 500 pA Input Voltage Range 0 5 V Common-Mode Rejection Ratio CMRR V = 0 V to 5 V 137 160 dB CM −40°C ≤ T ≤ +125°C 122 dB A Open-Loop Gain A R = 10 kΩ, V = 0.1 V to 4.9 V 127 139 dB VO L O −40°C ≤ TA ≤ +125°C 125 dB RL = 2 kΩ, VO = 0.1 V to 4.9 V 121 131 dB −40°C ≤ T ≤ +125°C 120 dB A Input Resistance, Differential Mode R 190 kΩ INDM Input Resistance, Common Mode R 1 GΩ INCM Input Capacitance, Differential Mode CINDM 16.5 pF Input Capacitance, Common Mode CINCM 33 pF OUTPUT CHARACTERISTICS Output Voltage High VOH RL = 10 kΩ to VCM 4.99 4.995 V −40°C ≤ TA ≤ +125°C 4.98 V RL = 2 kΩ to VCM 4.96 4.98 V −40°C ≤ T ≤ +125°C 4.94 V A Output Voltage Low V R = 10 kΩ to V 5 10 mV OL L CM −40°C ≤ T ≤ +125°C 20 mV A RL = 2 kΩ to VCM 20 40 mV −40°C ≤ TA ≤ +125°C 60 mV Short-Circuit Current I ±40 mA SC Closed-Loop Output Impedance Z f = 1 kHz, A = +10 0.1 Ω OUT V POWER SUPPLY Power Supply Rejection Ratio PSRR V = 2.2 V to 5.5 V 130 150 dB SY −40°C ≤ T ≤ +125°C 127 dB A Supply Current/Amplifier I I = 0 mA 1.5 1.8 mA SY O −40°C ≤ TA ≤ +125°C 2.2 mA DYNAMIC PERFORMANCE Slew Rate SR R = 10 kΩ, C = 100 pF, A = +1 0.5 V/μs L L V Settling Time to 0.1% ts VIN = 4 V step, RL = 10 kΩ, CL = 100 pF, AV = −1 10 μs Gain Bandwidth Product GBP RL = 10 kΩ, CL = 100 pF, AV = +1 4 MHz Phase Margin Φ R = 10 kΩ, C = 100 pF, A = +1 57 Degrees M L L V Overload Recovery Time R = 10 kΩ, C = 100 pF, A = −10 50 μs L L V NOISE PERFORMANCE Voltage Noise e p-p f = 0.1 Hz to 10 Hz, A = +100 99 nV p-p n V Voltage Noise Density e f = 1 kHz, A = +100 5.9 nV/√Hz n V f = 1 kHz, A = +100, V = 4.5 V 5.3 nV/√Hz V CM Current Noise in p-p f = 0.1 Hz to 10 Hz, AV = +100 10 pA p-p Current Noise Density in f = 1 kHz, AV = +100 0.5 pA/√Hz Rev. A | Page 4 of 20 Data Sheet ADA4528-1 ABSOLUTE MAXIMUM RATINGS THERMAL RESISTANCE Table 4. θ is specified for the worst-case conditions, that is, a device JA Parameter Rating soldered in a circuit board for surface-mount packages. This Supply Voltage 6 V was measured using a 4-layer JEDEC thermal board with the Input Voltage ±V ± 0.3 V SY exposed pad soldered to the PCB. 1 Input Current ±10 mA Differential Input Voltage ±VSY Table 5. Thermal Resistance Output Short-Circuit Duration to GND Indefinite Package Type θJA θJC Unit Storage Temperature Range −65°C to +150°C 8-Lead MSOP (RM-8) 142 45 °C/W Operating Temperature Range −40°C to +125°C 8-Lead LFCSP (CP-8-12) 80 14 °C/W Junction Temperature Range −65°C to +150°C Lead Temperature (Soldering, 60 sec) 300°C 1 The input pins have clamp diodes to the power supply pins. Limit the input current to 10 mA or less whenever input signals exceed the ESD CAUTION power supply rail by 0.5 V. Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Rev. A | Page 5 of 20 ADA4528-1 Data Sheet TYPICAL PERFORMANCE CHARACTERISTICS TA = 25°C, unless otherwise noted. 100 100 V = 2.5V V = 5V SY SY 90 90 V = V /2 V = V /2 CM SY CM SY 80 80 70 70 60 60 50 50 40 40 30 30 20 20 10 10 0 0 –1.0 –0.8 –0.6 –0.4 –0.200 0.2 0.4.6 0.81.0 –1.0 –0.8 –0.6 –0.4 –0.200 0.2 0.4.6 0.81.0 V (µV) V (µV) OS OS Figure 3. Input Offset Voltage Distribution Figure 6. Input Offset Voltage Distribution 60 60 V = 2.5V V = 5V SY SY 50 50 V = V /2 V = V /2 CM SY CM SY 40 40 30 30 20 20 10 10 0 0 0931 6 215 0931 6 215 TCV (nV/°C) TCV (nV/°C) OS OS Figure 4. Input Offset Voltage Drift Distribution Figure 7. Input Offset Voltage Drift Distribution 1.0 1.0 V = 2.5V V = 5V SY SY 0.8 0.8 0.6 0.6 0.4 0.4 0.2 0.2 0 0 –0.2 –0.2 –0.4 –0.4 –0.6 –0.6 –0.8 –0.8 –1.0 –1.0 00.5 1.0 1.5 2.0 2.5 01 2 3 4 5 V (V) V (V) CM CM Figure 5. Input Offset Voltage vs. Common-Mode Voltage Figure 8. Input Offset Voltage vs. Common-Mode Voltage Rev. A | Page 6 of 20 V (µV) OS NUMBER OF AMPLIFIERS NUMBER OF AMPLIFIERS 09437-003 09437-002 09437-004 V (µV) OS NUMBER OF AMPLIFIERS NUMBER OF AMPLIFIERS 09437-006 09437-005 09437-007 Data Sheet ADA4528-1 400 400 V = 2.5V V = 5V SY SY 300 V = V /2 300 V = V /2 CM SY CM SY I + B 200 200 I + B 100 100 0 0 I – B –100 –100 I – B –200 –200 –300 –300 –400 –400 –50 –25 0 25 50 75 100 125 –50 –25 0 25 50 75 100 125 TEMPERATURE (°C) TEMPERATURE (°C) Figure 12. Input Bias Current vs. Temperature Figure 9. Input Bias Current vs. Temperature 600 600 400 +85°C 400 +85°C –40°C 200 –40°C 200 +25°C 0 +25°C +125°C 0 –200 +125°C –200 –400 –400 –600 V = 5V SY V = 2.5V SY –800 –600 0 123 45 0 0.5 1.0 1.5 2.0 2.5 V (V) CM V (V) CM Figure 13. Input Bias Current vs. Common-Mode Voltage Figure 10. Input Bias Current vs. Common-Mode Voltage 10 10 V = 5V V = 2.5V S SY 1 1 100m 100m –40°C –40°C +25°C +25°C +85°C +85°C 10m 10m +125°C +125°C 1m 1m 0.1m 0.1m 0.001 0.01 0.1 1 10 100 0.01 10 100 0.001 0.1 1 LOAD CURRENT (mA) LOAD CURRENT (mA) Figure 14. Output Voltage (V ) to Supply Rail vs. Load Current OL Figure 11. Output Voltage (VOL) to Supply Rail vs. Load Current Rev. A | Page 7 of 20 OUTPUT VOLTAGE (V ) TO SUPPLY RAIL (V) I (pA) I (pA) OL B B 09437-009 09437-014 09437-008 OUTPUT VOLTAGE (V ) TO SUPPLY RAIL (V) I (pA) I (pA) OL B B 09437-017 09437-012 09437-110 ADA4528-1 Data Sheet 10 10 V = 2.5V V = 5V SY SY 1 1 –40°C 100m 100m +25°C +85°C –40°C +125°C +25°C 10m 10m +85°C +125°C 1m 1m 0.1m 0.1m 0.001 0.01 0.1 1 10 100 0.001 0.01 0.1 1 10 100 LOAD CURRENT (mA) LOAD CURRENT (mA) Figure 15. Output Voltage (V ) to Supply Rail vs. Load Current Figure 18. Output Voltage (V ) to Supply Rail vs. Load Current OH OH 25 45 V = 5V SY V = 2.5V SY 40 R = 2kΩ L R = 2kΩ L 20 35 30 15 25 20 10 15 R = 10kΩ L R = 10kΩ L 10 5 5 0 0 –50 –25 0 255075 100 125 –50 –25 0 25 50 75 100 125 TEMPERATURE (°C) TEMPERATURE (°C) Figure 16. Output Voltage (VOL) to Supply Rail vs. Temperature Figure 19. Output Voltage (VOL) to Supply Rail vs. Temperature 25 25 V = 2.5V V = 5V SY SY R = 2kΩ R = 2kΩ L L 20 20 15 15 10 10 R = 10kΩ R = 10kΩ L L 5 5 0 0 –50 –25 0 255075 100 125 –50 –25 0 25 50 75 100 125 TEMPERATURE (°C) TEMPERATURE (°C) Figure 17. Output Voltage (V ) to Supply Rail vs. Temperature Figure 20. Output Voltage (V ) to Supply Rail vs. Temperature OH OH Rev. A | Page 8 of 20 OUTPUT VOLTAGE (V ) TO SUPPLY RAIL (V) OH OUTPUT VOLTAGE (V ) TO SUPPLY RAIL (mV) OUTPUT VOLTAGE (V ) TO SUPPLY RAIL (mV) OH OL 09437-015 09437-016 09437-010 OUTPUT VOLTAGE (V ) TO SUPPLY RAIL (V) OH OUTPUT VOLTAGE (V ) TO SUPPLY RAIL (mV) OUTPUT VOLTAGE (V ) TO SUPPLY RAIL (mV) OL OH 09437-117 09437-019 09437-013 Data Sheet ADA4528-1 2.00 2.0 +125°C 1.75 1.8 +85°C 1.50 +25°C V = 5.0V SY 1.25 1.6 –40°C 1.00 1.4 V = 2.5V SY 0.75 0.50 1.2 0.25 0 1.0 0 0.51.01.52.02.53.03.54.04.55.05.5 –50 –25 0 25 50 75 100 125 V (V) SY TEMPERATURE (°C) Figure 21. Supply Current vs. Supply Voltage Figure 24. Supply Current vs. Temperature 120 135 120 135 PHASE PHASE 90 90 90 90 60 45 60 45 GAIN GAIN 30 0 30 0 V = 2.5V V = 5V SY SY 0 –45 0 –45 R = 10kΩ R = 10kΩ L L C = 100pF C = 100pF L L –30 –90 –30 –90 1k 10k 100k 1M 10M 1k 10k 100k 1M 10M FREQUENCY (Hz) FREQUENCY (Hz) Figure 22. Open-Loop Gain and Phase vs. Frequency Figure 25. Open-Loop Gain and Phase vs. Frequency 60 60 V = 2.5V V = 5V SY SY 50 50 A = 100 A = 100 V V 40 40 30 30 = 10 A A = 10 V V 20 20 10 10 A = 1 A = 1 V V 0 0 –10 –10 –20 –20 10 100 1k 10k 100k 1M 10M 10 100 1k 10k 100k 1M 10M FREQUENCY (Hz) FREQUENCY (Hz) Figure 23. Closed-Loop Gain vs. Frequency Figure 26. Closed-Loop Gain vs. Frequency Rev. A | Page 9 of 20 OPEN-LOOP GAIN (dB) CLOSED-LOOP GAIN (dB) I PER AMPLIFIER (mA) SY 09437-026 PHASE (Degrees) 09437-021 09437-022 OPEN-LOOP GAIN (dB) CLOSED-LOOP GAIN (dB) I PER AMPLIFIER (mA) SY 09437-024 09437-029 PHASE (Degrees) 09437-025 ADA4528-1 Data Sheet 160 140 V = 2.5V SY V = 5V SY 140 120 V = V /2 CM SY 120 100 100 80 80 60 60 40 40 V = V /2 CM SY 20 20 V = 1.1V CM 0 0 100 1k 10k 100k 1M 10M 100 1k 10k 100k 1M 10M FREQUENCY (Hz) FREQUENCY (Hz) Figure 27. CMRR vs. Frequency Figure 30. CMRR vs. Frequency 120 120 V = 5V V = 2.5V SY SY 100 100 80 80 60 60 PSRR+ PSRR+ 40 40 PSRR– PSRR– 20 20 0 0 –20 –20 100 1k 10k 100k 1M 10M 100 1k 10k 100k 1M 10M FREQUENCY (Hz) FREQUENCY (Hz) Figure 28. PSRR vs. Frequency Figure 31. PSRR vs. Frequency 1k 1k V = 2.5V V = 5V SY SY 100 100 10 10 A = 100 V A = 100 A = 10 V A = 10 V V 1 1 A = 1 A = 1 V V 0.1 0.1 0.01 0.01 0.001 0.001 100 1k 10k 100k 1M 10M 100 1k 10k 100k 1M 10M FREQUENCY (Hz) FREQUENCY (Hz) Figure 29. Output Impedance vs. Frequency Figure 32. Output Impedance vs. Frequency Rev. A | Page 10 of 20 Z (Ω) OUT PSRR (dB) CMRR (dB) 09437-032 09437-126 09437-027 Z (Ω) OUT PSRR (dB) CMRR (dB) 09437-035 09437-031 09437-030 Data Sheet ADA4528-1 V = ±1.25V V = ±2.5V SY SY V = 2V p-p V = 4V p-p IN IN A = 1 A = 1 V V R = 10kΩ R = 10kΩ L L C = 100pF C = 100pF L L TIME (20µs/DIV) TIME (20µs/DIV) Figure 33. Large Signal Transient Response Figure 36. Large Signal Transient Response V = ±1.25V SY V = 100mV p-p IN V = ±2.5V A = 1 SY V V = 100mV p-p R = 10kΩ IN L A = 1 C = 100pF V L R = 10kΩ L C = 100pF L TIME (1µs/DIV) TIME (1µs/DIV) Figure 34. Small Signal Transient Response Figure 37. Small Signal Transient Response 16 16 V = 2.5V V = 5V SY SY V = 100mV p-p V = 100mV p-p IN IN 14 14 A = 1 A = 1 V V R = 10kΩ R = 10kΩ L L 12 12 OS+ 10 10 OS+ 8 8 OS– 6 6 OS– 4 4 2 2 0 0 1 10 100 1000 1 10 100 1000 LOAD CAPACITANCE (pF) LOAD CAPACITANCE (pF) Figure 35. Small Signal Overshoot vs. Load Capacitance Figure 38. Small Signal Overshoot vs. Load Capacitance Rev. A | Page 11 of 20 OVERSHOOT (%) VOLTAGE (50mV/DIV) VOLTAGE (0.5V/DIV) 09437-038 09437-034 09437-033 OVERSHOOT (%) VOLTAGE (50mV/DIV) VOLTAGE (1V/DIV) 09437-041 09437-037 09437-036 ADA4528-1 Data Sheet 0.5 0.5 INPUT INPUT 0 0 –0.5 –0.5 V = ±2.5V SY V = ±1.25V SY A = –10 V A = –10 V V = 375mV 3 IN V = 187.5mV IN R = 10kΩ L R = 10kΩ L 2 C = 100pF L C = 100pF L 2 OUTPUT 1 1 OUTPUT 0 0 –1 –1 TIME (10µs/DIV) TIME (10µs/DIV) Figure 39. Positive Overload Recovery Figure 42. Positive Overload Recovery 0.5 0.5 INPUT INPUT 0 0 –0.5 –0.5 1 V = ±1.25V SY V = 187.5mV IN OUTPUT A = –10 V R = 10kΩ L 1 0 C = 100pF L OUTPUT 0 V = ±2.5V –1 SY A = –10 V V = 375mV IN R = 10kΩ –1 L –2 C = 100pF L –2 –3 TIME (10µs/DIV) TIME (10µs/DIV) Figure 40. Negative Overload Recovery Figure 43. Negative Overload Recovery INPUT INPUT V = 5V V = 2.5V SY SY R = 10kΩ R = 10kΩ L L C = 100pF C = 100pF L L DUT A = –1 DUT A = –1 V V +20mV +7.5mV OUTPUT OUTPUT 0 0 ERROR BAND ERROR BAND POST GAIN = 5 –7.5mV POST GAIN = 5 –20mV TIME (10µs/DIV) TIME (10µs/DIV) Figure 41. Positive Settling Time to 0.1% Figure 44. Positive Settling Time to 0.1% Rev. A | Page 12 of 20 INPUT VOLTAGE (V) INPUT VOLTAGE (V) VOLTAGE (1V/DIV) OUTPUT VOLTAGE (V) OUTPUT VOLTAGE (V) 09437-044 09437-039 09437-040 INPUT VOLTAGE (V) INPUT VOLTAGE (V) VOLTAGE (2V/DIV) OUTPUT VOLTAGE (V) OUTPUT VOLTAGE (V) 09437-047 09437-042 09437-043 Data Sheet ADA4528-1 V = 2.5V V = 5V SY SY R = 10kΩ R = 10kΩ L L C = 100pF C = 100pF L L DUT A = –1 DUT A = –1 V V INPUT INPUT +20mV +7.5mV ERROR BAND OUTPUT POST GAIN = 5 OUTPUT 0 0 ERROR BAND –7.5mV POST GAIN = 5 –20mV TIME (10µs/DIV) TIME (10µs/DIV) Figure 45. Negative Settling Time to 0.1% Figure 48. Negative Settling Time to 0.1% 100 100 V = 2.5V V = 5V SY SY A = 100 A = 100 V V V = V /2 V = V /2 CM SY CM SY 10 10 1 1 1 10 100 1k 10k 1 10 100 1k 10k FREQUENCY (Hz) FREQUENCY (Hz) Figure 46. Voltage Noise Density vs. Frequency Figure 49. Voltage Noise Density vs. Frequency 10 10 V = 2.5V V = 5V SY SY A = 100 V A = 100 V V = V /2 CM SY V = V /2 CM SY 1 1 0.1 0.1 1 10 100 1k 10k 100k 1 10 100 1k 10k 100k FREQUENCY (Hz) FREQUENCY (Hz) Figure 47. Current Noise Density vs. Frequency Figure 50. Current Noise Density vs. Frequency Rev. A | Page 13 of 20 VOLTAGE (1V/DIV) CURRENT NOISE DENSITY (pA/√Hz) VOLTAGE NOISE DENSITY (nV/√Hz) 09437-046 09437-150 09437-045 VOLTAGE (2V/DIV) CURRENT NOISE DENSITY (pA/√Hz) VOLTAGE NOISE DENSITY (nV/√Hz) 09437-049 09437-153 09437-048 ADA4528-1 Data Sheet V = 2.5V V = 5V SY SY A = 100 A = 100 V V V = V /2 V = V /2 CM SY CM SY TIME (1s/DIV) TIME (1s/DIV) Figure 51. 0.1 Hz to 10 Hz Noise Figure 54. 0.1 Hz to 10 Hz Noise 10 10 1 1 0.1 0.1 V = 5V SY 0.01 0.01 V = 2.5V SY A = 1 V A = 1 V f = 1kHz f = 1kHz R = 10kΩ L R = 10kΩ L 0.001 0.001 0.001 0.01 0.1 1 10 0.001 0.01 0.1 1 10 AMPLITUDE (V p-p) AMPLITUDE (V p-p) Figure 52. THD + Noise vs. Amplitude Figure 55. THD + Noise vs. Amplitude 1 1 V = 2.5V V = 5V SY SY R = 10kΩ R = 10kΩ L L A = 1 A = 1 V V 80kHz LOW-PASS FILTER 80kHz LOW-PASS FILTER V = 2V p-p V = 2V p-p IN IN 0.1 0.1 0.01 0.01 0.001 0.001 10 100 1k 10k 100k 10 100 1k 10k 100k FREQUENCY (Hz) FREQUENCY (Hz) Figure 53. THD + Noise vs. Frequency Figure 56. THD + Noise vs. Frequency Rev. A | Page 14 of 20 THD + N (%) THD + N (%) INPUT VOLTAGE (20nV/DIV) 09437-050 09437-152 09437-056 THD + N (%) THD + N (%) INPUT VOLTAGE (20nV/DIV) 09437-053 09437-155 09437-057 Data Sheet ADA4528-1 3 APPLICATIONS INFORMATION V IN 2 V The ADA4528-1 is a precision, ultralow noise, zero-drift opera- OUT tional amplifier that features a patented chopping technique. This 1 chopping technique offers ultralow input offset voltage of 0.3 μV o typical and input offset voltage drift of 0.002 μV/ C typical. 0 Offset voltage errors due to common-mode voltage swings and power supply variations are also corrected by the chopping tech- –1 nique, resulting in a typical CMRR figure of 158 dB and a PSRR V = ±2.5V SY figure of 150 dB at 2.5 V supply voltage. The ADA4528-1 has low A = 1 –2 V R = 10kΩ L broadband noise of 5.6 nV/√Hz (at f = 1 kHz, AV = +100, VSY = 2.5 V) and no 1/f noise component. These features are ideal for –3 TIME (200µs/DIV) amplification of low level signals in dc or subhertz high Figure 57. Rail-to Rail Input and Output precision applications. NOISE CONSIDERATIONS INPUT PROTECTION 1/f noise The ADA4528-1 has internal ESD protection diodes that are connected between the inputs and each supply rail. These diodes 1/f noise, also known as pink noise or flicker noise, is inherent protect the input transistors in the event of electrostatic dis- in semiconductor devices and increases as frequency decreases. charge and are reverse-biased during normal operation. This At low frequency, 1/f noise is a major noise contributor and causes protection scheme allows voltages as high as approximately a significant output voltage offset when amplified by the noise 300 mV beyond the rails to be applied at the input of either gain of the circuit. However, the ADA4528-1 eliminates the 1/f terminal without causing permanent damage. Refer to Table 4 noise internally, thus making it an excellent choice for dc or in the Absolute Maximum Ratings section. subhertz high precision applications. The 0.1 Hz to 10 Hz am- plifier voltage noise is only 97 nV p-p (AV = +100) at 2.5 V of When either input exceeds one of the supply rails by more than supply voltage. 300 mV, these ESD diodes become forward-biased and large amounts of current begin to flow through them. Without current The low frequency 1/f noise appears as a slow varying offset to limiting, this excessive fault current causes permanent damage the ADA4528-1 and is greatly reduced by the chopping technique. to the device. If the inputs are expected to be subject to overvoltage This allows the ADA4528-1 to have a much lower noise at dc conditions, insert a resistor in series with each input to limit the and low frequency in comparison to standard low noise amplifiers input current to 10 mA maximum. However, consider the resistor that are susceptible to 1/f noise. Figure 46 and Figure 49 show thermal noise effect on the entire circuit. the voltage noise density of the amplifier with no 1/f noise. At a 5 V supply voltage, the broadband voltage noise of the Source Resistance ADA4528-1 is approximately 6 nV/√Hz (at unity gain), and a The ADA4528-1 is one of the lowest noise zero drift amplifiers 1 kΩ resistor has thermal noise of 4 nV/√Hz. Adding a 1 kΩ with 5.6 nV/√Hz of broadband noise at 1 kHz (VSY = 2.5 V and resistor increases the total noise by 30% root sum square (rss). A = +100) currently available in the industry. Therefore, it is V important to consider the input source resistance of choice to RAIL-TO-RAIL INPUT AND OUTPUT maintain a total low noise. The total input referred broadband The ADA4528-1 features rail-to-rail input and output with a noise (e total) from any amplifier is primarily a function of N supply voltage from 2.2 V to 5.5 V. Figure 57 shows the input three types of noise: input voltage noise, input current noise, and output waveforms of the ADA4528-1 configured as a unity- and thermal (Johnson) noise from the external resistors. These gain buffer with a supply voltage of ±2.5 V and a resistive load uncorrelated noise sources can be summed up in a root sum of 10 kΩ. With an input voltage of ±2.5 V, the ADA4528-1 allows squared (rss) manner by using the following equation: the output to swing very close to both rails. Additionally, it does 2 2 1/2 e total = [e + 4 kTR + (i × R ) ] N n S n S not exhibit phase reversal. where: e is the input voltage noise of the amplifier (V/√Hz). n In is the input current noise of the amplifier (A/√Hz). RS is the total input source resistance (Ω). −23 k is the Boltzmann’s constant (1.38 × 10 J/K). T is the temperature in Kelvin (K). Rev. A | Page 15 of 20 VOLTAGE (V) 09437-059 ADA4528-1 Data Sheet 100 The total equivalent rms noise over a specific bandwidth is V = 5V SY expressed as V = V /2 CM SY e = e total √BW N,RMS N where BW is the bandwidth in hertz. This analysis is valid for broadband noise calculation. If the 10 bandwidth of concern includes the chopping frequency, more complicated calculations must be made to include the effect of the noise spike at the chopping frequency (see Figure 60). A = 1 V A = 10 With a low source resistance of R < 1 kΩ, the voltage noise of S V A = 100 V the amplifier dominates. As source resistance increases, the thermal noise of R dominates. As the source resistance further S 1 1 10 100 1k 10k increases, where RS > 100 kΩ, the current noise becomes the FREQUENCY (Hz) main contributor of the total input noise. A good selection table Figure 59. Voltage Noise Density vs. Frequency for low noise op amps can be found in the AN-940 Application Residual Ripple Note, Low Noise Amplifier Selection Guide for Optimal Noise Although the ACFB suppresses the chopping related ripples, Performance. there exists higher noise spectrum at the chopping frequency Voltage Noise Density with Different Gain Configurations and its harmonics due to the remaining ripples. Figure 60 shows Figure 58 shows the voltage noise density vs. closed-loop gain of the voltage noise density of the ADA4528-1 configured in unity a zero-drift amplifier from Competitor A. The voltage noise density gain. A noise spike of 50 nV/√Hz can be seen at the chopping of the amplifier increases from 11 nV/√Hz to 21 nV/√Hz as closed- frequency of 200 kHz. This noise spike is significant when the loop gain decreases from 1000 to 1. Figure 59 shows the voltage op amp has a closed-loop frequency that is higher than the noise density vs. frequency of the ADA4528-1 for three different chopping frequency. To further suppress the noise to a desired gain configurations. The ADA4528-1 offers lower input voltage level, it is recommended to have a post filter at the output of the noise density of 6 nV/√Hz to 7 nV/√Hz regardless of gain amplifier. configurations. 100 24 SY V V = 5V SY CM SY f = 100Hz 20 COMPETITOR A 16 10 12 8 4 1 1 10 100 1k 10k 100k 1M 10M 0 1 10 100 1000 CLOSED-LOOP GAIN (V/V) Figure 60. Voltage Noise Density Figure 58. Competitor A: Voltage Noise Density vs. Closed-Loop Gain Rev. A | Page 16 of 20 V = 5V A = 1 V = V /2 FREQUENCY (Hz) VOLTAGE NOISE DENSITY (nV/√Hz) 09437-061 VOLTAGE NOISE DENSITY (nV/√Hz) VOLTAGE NOISE DENSITY (nV/√Hz) 09437-063 09437-062 Data Sheet ADA4528-1 COMPONENT PRINTED CIRCUIT BOARD LAYOUT LEAD The ADA4528-1 is a high precision device with ultralow offset V V SC2 SOLDER SC1 SURFACE-MOUNT + voltage and noise. Therefore, care must be taken in the design of COMPONENT V V TS1 TS2 + the printed circuit board (PCB) layout to achieve optimum performance of the ADA4528-1 at board level. PC BOARD To avoid leakage currents, keep the surface of the board clean T T A1 A2 and free of moisture. Coating the board surface creates a barrier IF T ≠ T , THEN COPPER A1 A2 TRACE V + V ≠ V + V TS1 SC1 TS2 SC2 to moisture accumulation and reduces parasitic resistance on Figure 61. Mismatch in Seebeck Voltages Causes the board. Seebeck Voltage Error Properly bypassing the power supplies and keeping the supply To minimize these thermocouple effects, orient resistors so that traces short minimizes power supply disturbances caused by heat sources warm both ends equally. Where possible, the input output current variation. Connect bypass capacitors as close signal paths should contain matching numbers and types of com- as possible to the device supply pins. Stray capacitances are a ponents to match the number and type of thermocouple junctions. concern at the outputs and the inputs of the amplifier. It is For example, dummy components, such as zero value resistors, recommended that signal traces be kept at a distance of at can be used to match the thermoelectric error source (real resistors least 5 mm from supply lines to minimize coupling. in the opposite input path). Place matching components in close A potential source of offset error is the Seebeck voltage on the proximity and orient them in the same manner to ensure equal circuit board. The Seebeck voltage occurs at the junction of two Seebeck voltages, thus cancelling thermal errors. Additionally, dissimilar metals and is a function of the temperature of the use leads that are of equal length to keep thermal conduction in junction. The most common metallic junctions on a circuit board equilibrium. Keep heat sources on the PCB as far away from are solder-to-board trace and solder-to-component lead. Figure 61 amplifier input circuitry as is practical. shows a cross section of a surface-mount component soldered It is highly recommended to use a ground plane. A ground to a PCB. A variation in temperature across the board (where T A1 ≠ plane helps distribute heat throughout the board, maintains a TA2) causes a mismatch in the Seebeck voltages at the solder joints, constant temperature across the board, and reduces EMI noise thereby resulting in thermal voltage errors that degrade the per- pickup. formance of the ultralow offset voltage of the ADA4528-1. Rev. A | Page 17 of 20 09437-154 + + ADA4528-1 Data Sheet OUTLINE DIMENSIONS 3.20 3.00 2.80 8 5 5.15 3.20 4.90 3.00 4.65 1 2.80 4 PIN 1 IDENTIFIER 0.65 BSC 0.95 15° MAX 0.85 1.10 MAX 0.75 0.80 0.15 0.23 6° 0.55 0.40 0.05 0.09 0° 0.40 0.25 COPLANARITY 0.10 COMPLIANT TO JEDEC STANDARDS MO-187-AA Figure 62. 8-Lead Mini Small Outline Package [MSOP] (RM-8) Dimensions shown in millimeters 3.10 3.00 SQ 0.50 BSC 2.90 5 8 PIN 1 INDEX EXPOSED 1.70 PAD AREA 1.60 SQ 1.50 0.50 0.40 0.30 4 1 TOP VIEW BOTTOM VIEW FOR PROPER CONNECTION OF 0.80 THE EXPOSED PAD, REFER TO 0.05 MAX 0.75 THE PIN CONFIGURATION AND 0.02 NOM 0.70 FUNCTION DESCRIPTIONS COPLANARITY SECTION OF THIS DATA SHEET. 0.08 SEATING 0.30 PLANE 0.203 REF 0.25 0.20 COMPLIANT TOJEDEC STANDARDS MO-229-WEED Figure 63.8-Lead Lead Frame Chip Scale Package [LFCSP_WD] 3 mm × 3 mm Body, Very Very Thin, Dual Lead (CP-8-12) Dimensions shown in millimeters ORDERING GUIDE 1 Model Temperature Range Package Description Package Option Branding ADA4528-1ARMZ −40°C to +125°C 8-Lead Mini Small Outline Package [MSOP] RM-8 A2R ADA4528-1ARMZ-R7 −40°C to +125°C 8-Lead Mini Small Outline Package [MSOP] RM-8 A2R ADA4528-1ARMZ-RL −40°C to +125°C 8-Lead Mini Small Outline Package [MSOP] RM-8 A2R ADA4528-1ACPZ-R7 −40°C to +125°C 8-Lead Lead Frame Chip Scale Package [LFCSP_WD] CP-8-12 A2R ADA4528-1ACPZ-RL −40°C to +125°C 8-Lead Lead Frame Chip Scale Package [LFCSP_WD] CP-8-12 A2R 1 Z = RoHS Compliant Part. Rev. A | Page 18 of 20 PIN 1 INDICATOR (R 0.15) 10-07-2009-B 07-06-2011-A Data Sheet ADA4528-1 NOTES Rev. A | Page 19 of 20 ADA4528-1 Data Sheet NOTES ©2011 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D09437-0-9/11(A) Rev. A | Page 20 of 20

Frequently asked questions

What makes Elite.Parts unique?

chervon down
At GID Industrial (Elite.Parts' parent company), we specialize in procuring industrial parts. We know where to find the rare and obsolete equipment that our customers need in order to get back to business. There are other companies who claim to do what we do, but we're confident that our commitment to quality and value is unparalleled in our field.

What kind of warranty will the ADA4528-1 have?

chervon down
Warranties differ by part and by which suppliers we use to procure it for you. Sometimes, a part will be sold as-is and without a warranty. Our specialty, single board computers, tend to receive a one-year warranty.

Which carriers does Elite.Parts work with?

chervon down
Elite.Parts can ship via FedEx, UPS, DHL, and USPS. We have accounts with each of them and generally ship using one of those, but we can also ship using your account if you would prefer. However, we can use other carriers if it will be more convenient for you.

Will Elite.Parts sell to me even though I live outside the USA?

chervon down
Absolutely! We are happy to serve customers regardless of location. We work with international clients all the time, and we are familiar with shipping to destinations all across the globe.

I have a preferred payment method. Will Elite.Parts accept it?

chervon down
All major credit cards are accepted: Visa, MasterCard, Discover, and American Express. We will also accept payment made with wire transfer or PayPal. Checks will only be accepted from customers in the USA. Terms may available for larger orders, upon approval.

Why buy from GID?

quality

Quality

We are industry veterans who take pride in our work

protection

Protection

Avoid the dangers of risky trading in the gray market

access

Access

Our network of suppliers is ready and at your disposal

savings

Savings

Maintain legacy systems to prevent costly downtime

speed

Speed

Time is of the essence, and we are respectful of yours

What they say about us

FANTASTIC RESOURCE

star star star star star

One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!

Bucher Emhart Glass

EXCELLENT SERVICE

star star star star star

With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.

Fuji

HARD TO FIND A BETTER PROVIDER

star star star star star

Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.

Applied Materials

CONSISTENTLY DELIVERS QUALITY SOLUTIONS

star star star star star

Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.

Nidec Vamco

TERRIFIC RESOURCE

star star star star star

This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.

Trican Well Service

GO TO SOURCE

star star star star star

When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.

ConAgra Foods

Related Products

ANALOG DEVICE# A5E1032

SOCKET FOR MODEL AD210 IC

TRANSFORMER CURRENT 60.0 AMP

SOCKET FOR MODEL 1B22 IC

product

Analog Devices AD7291 12-Bit Low power 8-Channel Successive Approximation Analog-to-Digital Converte...