ANALOG DEVICES ADA4311-1
Description
Analog Devices ADA4311-1 High-Speed, Current Feedback Operational Amplifier
Part Number
ADA4311-1
Price
Request Quote
Manufacturer
ANALOG DEVICES
Lead Time
Request Quote
Category
PRODUCTS - A
Specifications
-3 dB BW (MHz)
310MHz
Distortion (dBc)
-98dBc
Function
Driver
Minimum Gain (Acl)
5
Slew Rate (V/us)
1050V/µs
Spectral Noise (nV/rtHz)
2.4nV/rtHz
Features
- Control inputs CMOS level compatible
- High output current
- High speed: -3 dB bandwidth: 310 MHz, G = +5, RLOAD = 50 O; Slew rate: 1050 V/µs, RLOAD = 50 O
- Low distortion: -98 dBc typical at 1 MHz, VOUT = 2 V p-p, G = +5, RLOAD = 100 O; -72 dBc typical at 10 MHz, VOUT = 2 V p-p, G = +5, RLOAD = 100 O
- Power management and shutdown
- Selectable quiescent current: 1 mA to 11.8 mA/amplifier
- Shutdown quiescent current: 1 mA/amplifier
- Wide output swing: 20.6 V p-p differential, RLOAD of 100 O from 12 V supply
Datasheet
Extracted Text
Low Cost, Dual, High Current Output Line Driver with Shutdown ADA4311-1 FEATURES PIN CONFIGURATION ADA4311-1 High speed +V 1 10 OUT B S −3 dB bandwidth: 310 MHz, G = +5, R = 50 Ω LOAD NC 2 9 –IN B Slew rate: 1050 V/μs, R = 50 Ω LOAD OUT A 3 8 +IN B Wide output swing –IN A 4 7 PD1 20.6 V p-p differential, R of 100 Ω from 12 V supply LOAD +IN A 5 6 PD0 High output current NC = NO CONNECT Low distortion Figure 1. Thermally Enhanced, 10-Lead MINI_SO_EP −98 dBc typical at 1 MHz, V = 2 V p-p, G = +5, R = 100 Ω OUT LOAD TYPICAL APPLICATION −72 dBc typical at 10 MHz, V = 2 V p-p, G = +5, R = 100 Ω OUT LOAD Power management and shutdown 1/2 Control inputs CMOS level compatible ADA4311-1 Shutdown quiescent current: 1 mA/amplifier V * Selectable quiescent current: 1 mA to 11.8 mA/amplifier MID APPLICATIONS 1/2 Home networking line drivers ADA4311-1 Twisted pair line drivers – V GND CC = *V Power line communications (PLC) MID 2 Video line drivers Figure 2. Typical PLC Driver Application ARB line drivers I/Q channel amplifiers GENERAL DESCRIPTION The ADA4311-1 is comprised of two high speed, current The ADA4311-1 is available in a thermally enhanced, 10-lead feedback operational amplifiers. The high output current, high MSOP with an exposed paddle for improved thermal conduction. bandwidth, and fast slew rate make it an excellent choice for The ADA4311-1 is rated to work in the extended industrial broadband applications requiring high linearity performance temperature range of −40°C to +85°C. while driving low impedance loads. The ADA4311-1 incorporates a power management function that provides shutdown capabilities and the ability to optimize the quiescent current of the amplifiers. The CMOS-compatible, power-down control pins (PD1 and PD0) enable the ADA4311-1 to operate in four different modes: full power, medium power, low power, and complete power-down. In power-down mode, the quiescent current drops to only 1.0 mA/amplifier, while the outputs go to a high impedance state. Rev. 0 Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. rights of third parties that may result from its use. Specifications subject to change without notice. No Tel: 781.329.4700 www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Fax: 781.461.3113 ©2007 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. 06940-001 06940-002 ADA4311-1 TABLE OF CONTENTS Features .............................................................................................. 1 Theory of Operation ...................................................................... 10 Applications....................................................................................... 1 Application Information................................................................ 11 Pin Configuration............................................................................. 1 Feedback Resistor Selection...................................................... 11 Typical Application........................................................................... 1 Power Control Modes of Operation ........................................ 11 General Description ......................................................................... 1 Exposed Thermal Pad Connections ........................................ 11 Revision History ............................................................................... 2 Powerline Application ............................................................... 11 Specifications..................................................................................... 3 Board Layout............................................................................... 12 Absolute Maximum Ratings............................................................ 5 Power Supply Bypassing............................................................ 12 Thermal Resistance ...................................................................... 5 Outline Dimensions ....................................................................... 13 ESD Caution.................................................................................. 5 Ordering Guide .......................................................................... 13 Pin Configuration and Function Descriptions............................. 6 Typical Performance Characteristics ............................................. 7 REVISION HISTORY 8/07—Revision 0: Initial Version Rev. 0 | Page 2 of 16 ADA4311-1 SPECIFICATIONS VS = 12 V, RF = 499 Ω (@ TA = 25°C, G = +5, RL = 100 Ω to VS/2), unless otherwise noted. Table 1. Parameter Test Conditions/Comments Min Typ Max Unit DYNAMIC PERFORMANCE −3 dB Bandwidth V = 0.1 V p-p, PD1 = 0, PD0 = 0, R = 50 Ω 310 MHz OUT LOAD VOUT = 0.1 V p-p, PD1 = 0, PD0 = 1, RLOAD = 50 Ω 220 MHz VOUT = 0.1 V p-p, PD1 = 1, PD0 = 0, RLOAD = 50 Ω 140 MHz Full Power Bandwidth VOUT = 10.2 V p-p, PD1 = 0, PD0 = 0, RLOAD = 50 Ω 12.9 MHz Slew Rate V = 2 V p-p, PD1 = 0, PD0 = 0 1050 V/μs OUT V = 2 V p-p, PD1 = 0, PD0 = 1 1050 V/μs OUT V = 2 V p-p, PD1 = 1, PD0 = 0 1000 V/μs OUT NOISE/DISTORTION PERFORMANCE Differential Distortion (Worst f = 1 MHz, V = 2 V p-p C OUT Harmonic) PD1 = 0, PD0 = 0 −98 dBc PD1 = 0, PD0 = 1 −95 dBc PD1 = 1, PD0 = 0 −86 dBc f = 10 MHz, V = 2 V p-p C OUT PD1 = 0, PD0 = 0 −72 dBc PD1 = 0, PD0 = 1 −63 dBc PD1 = 1, PD0 = 0 −52 dBc fC = 20 MHz, VOUT = 2 V p-p PD1 = 0, PD0 = 0 −56 dBc PD1 = 0, PD0 = 1 −49 dBc PD1 = 1, PD0 = 0 −43 dBc Input Voltage Noise f = 100 kHz 2.4 nV/√Hz Input Current Noise f = 100 kHz 17 pA/√Hz DC PERFORMANCE Input Offset Voltage −3 +1 +3 mV Input Bias Current Noninverting Input −9 −2 +3 μA Inverting Input −4 +4.5 +16 μA Open-Loop Transimpedance R = 50 Ω 4 14 MΩ LOAD RLOAD = 100 Ω 15 35 MΩ Common-Mode Rejection 57 62 dB INPUT CHARACTERISTICS Input Resistance +IN, f < 100 kHz 500 kΩ OUTPUT CHARACTERISTICS Single-Ended, +Swing RLOAD = 50 Ω 11 11.1 VP Single-Ended, −Swing RLOAD = 50 Ω 0.9 1 VP Single-Ended, +Swing RLOAD = 100 Ω 11 11.1 VP Single-Ended, −Swing R = 100 Ω 0.8 0.9 V LOAD P Differential Swing R = 100 Ω 20.2 20.6 V p-p LOAD POWER SUPPLY Single Supply 12 V Supply Current PD1 = 0, PD0 = 0 10.5 11.8 13 mA/amp PD1 = 0, PD0 = 1 7 7.9 9 mA/amp PD1 = 1, PD0 = 0 4.3 5.2 6.3 mA/amp PD1 = 1, PD0 = 1 0.9 1.3 mA/amp Rev. 0 | Page 3 of 16 ADA4311-1 Parameter Test Conditions/Comments Min Typ Max Unit POWER-DOWN PINS PD1, PD0 Threshold Referenced to GND 1.5 V High Level Input Voltage, VIH 2 5 V Low Level Input Voltage, V 0 0.8 V IL PD1, PD0 = 0 Pin Bias Current PD1 or PD0 = 0 V −1.5 −0.2 +1.5 μA PD1, PD0 = 1 Pin Bias Current PD1 or PD0 = 3 V 40 63 80 μA Enable/Disable Time 130/116 ns Power Supply Rejection Ratio −63 −70 dB Rev. 0 | Page 4 of 16 ADA4311-1 ABSOLUTE MAXIMUM RATINGS Maximum Power Dissipation Table 2. The maximum safe power dissipation for the ADA4311-1 is Parameter Rating limited by the associated rise in junction temperature (T ) on J Supply Voltage 13.6 V the die. At approximately 150°C, which is the glass transition Power Dissipation (T − T )/θ JMAX A JA temperature, the plastic changes its properties. Even temporarily Storage Temperature Range −65°C to +125°C exceeding this temperature limit can change the stresses that the Operating Temperature Range −40°C to +85°C package exerts on the die, permanently shifting the parametric Lead Temperature (Soldering 10 sec) 300°C performance of the amplifiers. Exceeding a junction temperature of Junction Temperature 150°C 150°C for an extended period can result in changes in silicon Stresses above those listed under Absolute Maximum Ratings devices, potentially causing degradation or loss of functionality. may cause permanent damage to the device. This is a stress rating Figure 3 shows the maximum safe power dissipation in only; functional operation of the device at these or any other the package vs. the ambient temperature for the 10-lead conditions above those indicated in the operational section of MINI_SO_EP (44°C/W) on a JEDEC standard 4-layer board. this specification is not implied. Exposure to absolute maximum θJA values are approximations. rating conditions for extended periods may affect device reliability. 5.0 THERMAL RESISTANCE 4.5 Thermal resistance (θ ) is specified for the worst-case conditions, JA 4.0 that is, θ is specified for device soldered in circuit board for JA 3.5 MINI_SO_EP-10 surface-mount packages. 3.0 Table 3. 2.5 Package Type θ Unit JA 2.0 10-Lead MINI_SO_EP 44 °C/W 1.5 1.0 0.5 0 –35 –15 5 25 45 65 85 AMBIENT TEMPERATURE (°C) Figure 3. Maximum Power Dissipation vs. Temperature for a 4-Layer Board ESD CAUTION Rev. 0 | Page 5 of 16 MAXIMUM POWER DISSIPATION (W) 06940-003 ADA4311-1 PIN CONFIGURATION AND FUNCTION DESCRIPTIONS ADA4311-1 +V 1 10 OUT B S NC 2 9 –IN B OUT A 3 8 +IN B –IN A 4 7 PD1 +IN A 5 6 PD0 NC = NO CONNECT Figure 4. Pin Configuration Table 4. Pin Function Description Pin No. Mnemonic Description 1 +VS Positive Power Supply Input. 2 NC No Connection. 3 OUT A Amplifier A Output. 4 −IN A Amplifier A Inverting Input. 5 +IN A Amplifier A Noninverting Input. 6 PD0 Power Dissipation Control. 7 PD1 Power Dissipation Control. 8 +IN B Amplifier B Noninverting Input. 9 −IN B Amplifier B Inverting Input. 10 OUT B Amplifier B Output. 11 (Exposed Paddle) GND Ground (Electrical Connection Required). Rev. 0 | Page 6 of 16 06940-004 ADA4311-1 TYPICAL PERFORMANCE CHARACTERISTICS 9 –40 V = 100mV p-p HD2 OUT V = 2V p-p OUT HD3 R = 50Ω L R = 100Ω L 6 –50 PD1, PD0 = 0, 0 G = +5 G = +5 3 –60 PD1, PD0 = 1, 0 0 –70 PD1, PD0 = 0, 1 –3 –80 PD1, PD0 = 0, 0 G = +10 –6 –90 –9 –100 G = +20 –12 –110 –15 –120 –18 –130 1 10 100 1000 0.1 110 100 FREQUENCY (MHz) FREQUENCY (MHz) Figure 5. Small Signal Frequency Response for Various Closed-Loop Gains Figure 8. Differential Harmonic Distortion vs. Frequency 9 –60 V = 100mV p-p f = 5MHz OUT 6 R = 50Ω R = 100Ω L L PD1, PD0 = 0, 0 G = +5 G = +5 –70 3 0 HD2 –80 –3 PD1, PD0 = 0, 1 –6 –90 –9 PD1, PD0 = 1, 0 HD3 –12 –100 –15 –18 –110 –21 –24 –120 1 10 100 1000 0.1 1 10 FREQUENCY (MHz) OUTPUT VOLTAGE (V p-p) Figure 6. Small Signal Frequency Response for Various Modes Figure 9. Differential Harmonic Distortion vs. Output Voltage 0.20 –40 G = +5 V = 2V p-p OUT R = 50Ω f = 5MHz L 0.15 10ns/DIV G = +5 –50 0.10 –60 0.05 –70 HD2 0 –80 –0.05 –90 –0.10 HD3 –100 –0.15 –0.20 –110 10 100 1000 LOAD RESISTANCE (Ω) Figure 7. Small Signal Transient Response Figure 10. Differential Harmonic Distortion vs. Load Resistance Rev. 0 | Page 7 of 16 GAIN (dB) NORMALIZED GAIN (dB) OUTPUT (V) 06940-010 06940-006 06940-005 HARMONIC DISTORTION (dBc) HARMONIC DISTORTION (dBc) HARMONIC DISTORTION (dBc) 06940-022 06940-021 06940-008 ADA4311-1 1000 100M 0 R = 100Ω PD1, PD0 = 0, 0 L 10M –45 100 PHASE 1M –90 10 100k –135 1 MAGNITUDE 10k –180 0.1 1k –225 0.01 100 –270 100 1k 10k 100k 1M 10M 100M 1G 0.01 0.1 1 10 100 1000 FREQUENCY (Hz) FREQUENCY (MHz) Figure 11. Open-Loop Transimpedance and Phase vs. Frequency Figure 14. Closed-Loop Output Impedance vs. Frequency 0 1M PD1, PD0 = 0, 0 PD1, PD0 = 1, 1 R = 100Ω L –10 100k –20 10k –30 1k –40 100 –50 10 –60 –70 1 0.01 0.1 1 10 100 1000 0.01 0.1 1 10 100 1000 FREQUENCY (MHz) FREQUENCY (MHz) Figure 12. Common-Mode Rejection vs. Frequency Figure 15. Output Impedance vs. Frequency (Disabled) –10 100 PD1, PD0 = 0, 0 R = 100Ω L –20 –30 +PSR –40 10 –50 –60 –70 1 0.01 0.1 1 10 100 1000 10 100 1k 10k 100k 1M 10M 100M 1G FREQUENCY (MHz) FREQUENCY (Hz) Figure 13. Power Supply Rejection vs. Frequency Figure 16. Voltage Noise vs. Frequency Rev. 0 | Page 8 of 16 TRANSIMPEDANCE (Ω) POWER SUPPLY REJECTION (dB) COMMON-MODE REJECTION (dB) 06940-012 06940-011 PHASE (Degrees) 06940-007 OUTPUT IMPEDANCE (Ω) VOLTAGE NOISE (nV/ Hz) OUTPUT IMPEDANCE (Ω) 06940-009 06940-015 06940-013 ADA4311-1 –20 0 PD1, PD0 = 1, 1 –20 –40 –40 –60 –60 –80 –80 –100 –100 1 10 100 1000 0.1 1 10 100 1000 FREQUENCY (MHz) FREQUENCY (Hz) Figure 17. Feedthrough vs. Frequency Figure 19. Crosstalk vs. Frequency 8 12 7 V OUT 11 6 10 5 4 9 3 8 V , V PD1 PD0 2 7 1 0 6 30 100 1000 012 345 6 TIME (1μs/DIV) LOAD (Ω) Figure 18. Power-Down Turn On/Turn Off Figure 20. Single-Ended Output Swing vs. Load Rev. 0 | Page 9 of 16 FEEDTHROUGH (dB) VOLTAGE (V) 06940-016 06940-014 V (p-p) CROSSTALK (dB) OUT 06940-020 06940-017 ADA4311-1 THEORY OF OPERATION The ADA4311-1 is a dual-current feedback amplifier with high Because G × RIN << RF for low gains, a current feedback amplifier output current capability. With a current feedback amplifier, the has relatively constant bandwidth vs. gain, the 3 dB point being current into the inverting input is the feedback signal, and the set when |TZ| = RF. open-loop behavior is that of a transimpedance, dVO/dIIN or TZ. For a real amplifier, there are additional poles that contribute The open-loop transimpedance is analogous to the open-loop excess phase, and there is a value for R below which the amplifier F voltage gain of a voltage feedback amplifier. Figure 21 shows a is unstable. Tolerance for peaking and desired flatness determines simplified model of a current feedback amplifier. Because R is the optimum R in each application. IN F proportional to 1/g , the equivalent voltage gain is T × g , m Z m R F where gm is the transconductance of the input stage. Basic R G analysis of the follower with gain circuit yields R IN V T() s OUT Z T Z V = G× I OUT IN V T() s + G× R + R IN Z IN F R N where: V IN R F G=1 + Figure 21. Simplified Block Diagram R G 1 R = ≈ 50 Ω IN g m Rev. 0 | Page 10 of 16 06940-018 ADA4311-1 APPLICATION INFORMATION FEEDBACK RESISTOR SELECTION Table 6. Power Modes Total Supply Output The feedback resistor has a direct impact on the closed-loop Current (mA) Impedance PD1 PD0 Power Mode bandwidth and stability of the current feedback op amp. Low Low Full Power 23.6 Low Reducing the resistance below the recommended value can Low High ¾ Power 15.8 Low make the amplifier response peak and even become unstable. High Low ½ Power 10.4 Low Increasing the size of the feedback resistor beyond the recom- High High Power-Down 1.8 High mended value reduces the closed-loop bandwidth. Table 5 provides a convenient reference for quickly determining the feedback and gain resistor values, and the corresponding EXPOSED THERMAL PAD CONNECTIONS bandwidth, for common gain configurations. The recommended The exposed thermal pad on the 10-lead MSOP is both the feedback resistor value for the ADA4311-1 is 499 Ω. reference for the PD pins and the only electrical connection for the negative supply voltage. Therefore, in the 10-lead MSOP, 1 Table 5. Recommended Values and Frequency Performance the ADA4311-1 can only be used on a single supply. The exposed Gain R (Ω) R (Ω) −3 dB SS BW (MHz) F G thermal pad must be connected to ground. Failure to do so +5 499 124 310 renders the part inoperable. +5 1 k 250 220 A requirement for this package is that the thermal pad be +10 499 55.4 175 connected to a solid plane with low thermal resistance, ensuring +20 499 26.1 84 adequate heat transfer away from the die and into the board. 1 Conditions: VS = ±12 V, TA = 25°C, RL = 50 Ω, PD1, PD0 = 0, 0. POWERLINE APPLICATION POWER CONTROL MODES OF OPERATION Applications (that is, powerline AV modems) requiring greater The ADA4311-1 features four power modes: full power, ¾ than 10 dBm peak power should consider using an external power, ½ power, and shutdown. The power modes are controlled line driver, such as the ADA4311-1. Figure 22 shows an example by two logic pins, PD0 and PD1. The power-down control pins interface between the TxDAC® output and the ADA4311-1 biased are compatible with standard 3 V and 5 V CMOS logic. Table 6 for single-supply operation. The peak-to-peak differential shows the various power modes and associated logic states. In output voltage swing of the TxDAC should be limited to the power-down mode, the output of the amplifier goes into a 2 V p-p, with the gain of the ADA4311-1 configured to realize high impedance state. the additional voltage gain required by the application. A low- pass filter should be considered to filter the DAC images inherent in the signal reconstruction process. In addition, dc blocking capacitors are required to level-shift the output signal of the TxDAC to the common-mode level of the ADA4311-1 (that is, V = V − GND/2). MID CC 0.1µF R SET OPTIONAL 1/2 LCLPF ADA4311-1 IOUTP+ V MID TxDAC IOUTP– 0dB TO –7.5dB 1/2 ADA4311-1 Figure 22. TxDAC Output Directly via Center-Tap Transformer Rev. 0 | Page 11 of 16 REFIO TxDISABLE REFADJ 06940-019 ADA4311-1 BOARD LAYOUT POWER SUPPLY BYPASSING As is the case with all high speed applications, careful attention The ADA4311-1 operates on supplies from 6 V to 12 V. The to printed circuit board (PCB) layout details prevents associated ADA4311-1 circuit should be powered with a well-regulated board parasitics from becoming problematic. Proper RF design power supply. Careful attention must be paid to decoupling the technique is mandatory. The PCB should have a ground plane power supply. High quality capacitors with low equivalent series covering all unused portions of the component side of the resistance (ESR), such as multilayer ceramic capacitors (MLCCs), board to provide a low impedance return path. Removing the should be used to minimize supply voltage ripple and power ground plane on all layers from the area near the input and dissipation. In addition, 0.1 μF MLCC decoupling capacitors output pins reduces stray capacitance, particularly in the area of should be located no more than ⅛-inch away from each of the the inverting inputs. Signal lines connecting the feedback and power supply pins. A large, usually tantalum, 10 μF capacitor is gain resistors should be as short as possible to minimize the required to provide good decoupling for lower frequency signals inductance and stray capacitance associated with these traces. and to supply current for fast, large signal changes at the Termination resistors and loads should be located as close as ADA4311-1 outputs. Bypassing capacitors should be laid out possible to their respective inputs and outputs. Input and in such a manner as to keep return currents away from the output traces should be kept as far apart as possible to minimize inputs of the amplifiers, which minimizes any voltage drops that coupling (crosstalk) though the board. Wherever there are can develop due to ground currents flowing through the ground complementary signals, a symmetrical layout should be provided plane. A large ground plane also provides a low impedance path to the extent possible to maximize balanced performance. for the return currents. When running differential signals over a long distance, the traces on the PCB should be close. Doing this reduces the radiated energy and makes the circuit less susceptible to RF interference. Adherence to stripline design techniques for long signal traces (greater than about 1 inch) is recommended. For more information on high speed board layout, see A Practical Guide to High-Speed Printed-Circuit-Board Layout. Rev. 0 | Page 12 of 16 ADA4311-1 OUTLINE DIMENSIONS * 2.27 3.10 2.17 3.00 2.07 2.90 10 6 5.05 * 3.10 1.83 TOP 4.90 1.73 3.00 VIEW 4.75 1.63 2.90 1 5 EXPOSED PIN 1 PAD INDICATOR BOTTOM VIEW 0.50 BSC 0.50 BSC 0.94 0.23 0.86 1.10 MAX 0.18 0.78 0.13 0.70 0.15 SEATING 0.55 8° 0.30 PLANE 0.10 0.40 0° 0.23 0.05 0.15 COPLANARITY 0.10 * COMPLIANT TO JEDEC STANDARDS MO-187-BA-T EXCEPT FOR EXPOSED PAD DIMENSIONS. Figure 23. 10-Lead Mini Small Outline Package with Exposed Pad [MINI_SO_EP] (RH-10-1) Dimensions shown in millimeters ORDERING GUIDE Package Model Temperature Range Package Description Option Branding 1 ADA4311-1ARHZ −40°C to +85°C 10-Lead Mini Small Outline Package with Exposed Pad [MINI_SO_EP] RH-10-1 1A 1 ADA4311-1ARHZ-RL −40°C to +85°C 10-Lead Mini Small Outline Package with Exposed Pad [MINI_SO_EP] RH-10-1 1A 1 ADA4311-1ARHZ-R7 −40°C to +85°C 10-Lead Mini Small Outline Package with Exposed Pad [MINI_SO_EP] RH-10-1 1A 1 Z = RoHS Compliant Part. Rev. 0 | Page 13 of 16 073007-B ADA4311-1 NOTES Rev. 0 | Page 14 of 16 ADA4311-1 NOTES Rev. 0 | Page 15 of 16 ADA4311-1 NOTES ©2007 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D06940-0-8/07(0) Rev. 0 | Page 16 of 16
Frequently asked questions
What makes Elite.Parts unique?
What kind of warranty will the ADA4311-1 have?
Which carriers does Elite.Parts work with?
Will Elite.Parts sell to me even though I live outside the USA?
I have a preferred payment method. Will Elite.Parts accept it?
Why buy from GID?
Quality
We are industry veterans who take pride in our work
Protection
Avoid the dangers of risky trading in the gray market
Access
Our network of suppliers is ready and at your disposal
Savings
Maintain legacy systems to prevent costly downtime
Speed
Time is of the essence, and we are respectful of yours
Manufacturers


What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods