ANALOG DEVICES ADA4051-1
Description
Analog Devices ADA4051-1 1.8V, CMOS, Micropower, Zero-Drift Operational, RRIO Single Amplifier
Part Number
ADA4051-1
Price
Request Quote
Manufacturer
ANALOG DEVICES
Lead Time
Request Quote
Category
PRODUCTS - A
Specifications
# OpAmps per Pkg
1
-3dB Bandwidth>
125kHz
Ib
20pA
Input Noise (nV/rtHz)
95nV/rtHz
Isy per Amplifier
15µA
Packages
SC70,SOT-23
Slew Rate
0.06V/µs
Vcc-Vee
1.8V to 5.5V
Vos
2µV
Features
- Extended industrial temperature range
- High CMRR: 110 dB minimum
- High PSRR: 110 dB minimum
- Low offset voltage: 15 µV maximum
- Offset voltage drift: 20 nV/°C
- Rail-to-rail input/output
- Single-supply operation: 1.8 V to 5.5 V
- Unity-gain stable
- Very low supply current: 13 µA typical
Datasheet
Extracted Text
1.8 V, Micropower, Zero-Drift, Rail-to-Rail Input/Output Op Amp ADA4051-1/ADA4051-2 FEATURES PIN CONFIGURATION Very low supply current: 13 μA typical OUT 1 5 V+ Low offset voltage: 15 μV maximum ADA4051-1 V– 2 TOP VIEW Offset voltage drift: 20 nV/°C (Not to Scale) Single-supply operation: 1.8 V to 5.5 V +IN 3 4 –IN High PSRR: 110 dB minimum High CMRR: 110 dB minimum Figure 1. 5-Lead SOT-23 (RJ-5) Rail-to-rail input/output +IN 1 Unity-gain stable 5 V+ ADA4051-1 Extended industrial temperature range V– 2 TOP VIEW (Not to Scale) APPLICATIONS –IN 3 4 OUT Pressure and position sensors Figure 2. 5-Lead SC-70 (KS-5) Temperature measurements Electronic scales OUT A 1 8 V+ –IN A 2 ADA4051-2 7 OUT B Medical instrumentation TOP VIEW +IN A 3 6 –IN B Battery-powered equipment (Not to Scale) V– 4 5 +IN B Handheld test equipment Figure 3. 8-Lead MSOP (RM-8) PIN 1 OUT A 1 8V+ INDICATOR –IN A 2 7OUT B ADA4051-2 +IN A 3 6 –IN B TOP VIEW V– 4 (Not to Scale) 5 +IN B NOTES 1. IT IS RECOMMENDED THAT THE EXPOSED PAD BE CONNECTED TO V–. Figure 4. 8-Lead LFCSP (CP-8-2) GENERAL DESCRIPTION The ADA4051-1/ADA4051-2 are CMOS, micropower, zero- The ADA4051-1/ADA4051-2 are specified for the extended drift operational amplifiers utilizing an innovative chopping industrial temperature range of −40°C to +125°C. The ADA4051-1 technique. These amplifiers feature rail-to-rail input/output amplifier is available in 5-lead SOT-23 and 5-lead SC-70 packages. swing and extremely low offset voltage while operating from a The ADA4051-2 amplifier is available in 8-lead MSOP and 8-lead 1.8 V to 5.5 V power supply. In addition, these amplifiers offer LFCSP packages. high power supply rejection ratio (PSRR) and common-mode The ADA4051-1/ADA4051-2 are members of a growing series rejection ratio (CMRR) while operating with a typical supply of zero-drift op amps offered by Analog Devices, Inc. Refer to current of 13 μA per amplifier. This combination of features Table 1 for a list of these devices. makes the ADA4051-1/ADA4051-2 amplifiers ideal choices for battery-powered applications where high precision and low Table 1. Op Amps power consumption are important. Supply Low Power, 5 V 5 V 16 V Single AD8538 AD8628 AD8638 Dual AD8539 AD8629 AD8639 Quad AD8630 Rev. B Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. rights of third parties that may result from its use. Specifications subject to change without notice. No Tel: 781.329.4700 www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Fax: 781.461.3113 ©2009–2010 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. 08056-066 08056-064 08056-001 08056-065 ADA4051-1/ADA4051-2 TABLE OF CONTENTS Features .............................................................................................. 1 Thermal Resistance .......................................................................5 Applications ....................................................................................... 1 Power Sequencing .........................................................................5 Pin Configuration ............................................................................. 1 ESD Caution...................................................................................5 General Description ......................................................................... 1 Typical Performance Characteristics ..............................................6 Revision History ............................................................................... 2 Theory of Operation ...................................................................... 15 Specif ica t ions ..................................................................................... 3 Input Voltage Range ................................................................... 16 Electrical Characteristics—1.8 V Operation ............................ 3 Output Phase Reversal ............................................................... 16 Electrical Characteristics—5 V Operation................................ 4 Outline Dimensions ....................................................................... 17 Absolute Maximum Ratings ............................................................ 5 Ordering Guide .......................................................................... 18 REVISION HISTORY 1/10—Rev. A to Rev. B Added ADA4051-1, 5-Lead SC-70 Package .................... Universal Added Figure 2; Renumbered Sequentially .................................. 1 Changes to Figure 4 and General Description Section ............... 1 Changes to Electrical Characteristics—1.8 V Operation Section and Table 2 ......................................................................................... 3 Changes to Electrical Characteristics—5 V Operation Section and Table 3 ......................................................................................... 4 Changes to Table 5 ............................................................................ 5 Updated Outline Dimensions ....................................................... 17 Changes to Ordering Guide .......................................................... 18 10/09—Rev. 0 to Rev. A Added ADA4051-1, 5-Lead SOT-23 Package ................. Universal Added ADA4051-2, 8-Lead LFCSP Package .................. Universal Changes to the Features and General Description Section, Added Figure 1 and Figure 3 ........................................................... 1 Moved Electrical Characteristics—1.8 V Operation Section .... 3 Changes to Offset Voltage Parameter and Supply Current per Amplifier Parameter, Table 2 .......................................................... 3 Moved Electrical Characteristics—5 V Operation Section ........ 4 Changes to Offset Voltage Parameter and Supply Current per Amplifier Parameter, Table 2 .......................................................... 4 Changes to Thermal Resistance Section and Table 5 ................... 5 Changes to Figure 22 and Figure 25 ............................................... 9 Changes to Theory of Operation Section .................................... 15 Updated Outline Dimensions ....................................................... 17 Changes to Ordering Guide .......................................................... 18 7/09—Revision 0: Initial Version Rev. B | Page 2 of 20 ADA4051-1/ADA4051-2 SPECIFICATIONS ELECTRICAL CHARACTERISTICS—1.8 V OPERATION V = 1.8 V, V = V /2 V, T = 25°C, R = 100 kΩ to GND, unless otherwise noted. SY CM SY A L Table 2. Parameter Symbol Test Conditions/Comments Min Typ Max Unit INPUT CHARACTERISTICS Offset Voltage VOS ADA4051-2 0 V ≤ V ≤ 1.8 V 2 15 μV CM ADA4051-1 0 V ≤ V ≤ 1.8 V 2 17 μV CM Offset Voltage Drift ∆VOS/∆T −40°C ≤ TA ≤ +125°C 0.02 0.1 μV/°C Input Bias Current IB 5 50 pA −40°C ≤ TA ≤ +125°C 200 pA Input Offset Current I 10 100 pA OS −40°C ≤ T ≤ +125°C 150 pA A Input Voltage Range −40°C ≤ T ≤ +125°C 0 1.8 V A Common-Mode Rejection Ratio CMRR 0 V ≤ VCM ≤ 1.8 V 105 125 dB −40°C ≤ TA ≤ +125°C 100 dB Large-Signal Voltage Gain AVO R = 10 kΩ to V , 106 130 dB L CM 0.1 V ≤ V ≤ V − 0.1 V OUT SY −40°C ≤ T ≤ +125°C 100 dB A Input Resistance RIN 8 MΩ Input Capacitance, Differential Mode CINDM 2 pF Input Capacitance, Common Mode CINCM 5 pF OUTPUT CHARACTERISTICS Output Voltage High VOH RL = 100 kΩ to VCM 1.796 1.799 V −40°C ≤ TA ≤ +125°C 1.79 V R = 10 kΩ to V 1.76 1.796 V L CM −40°C ≤ T ≤ +125°C 1.7 V A Output Voltage Low V R = 100 kΩ to V 1 3 mV OL L CM −40°C ≤ TA ≤ +125°C 9 mV RL = 10 kΩ to VCM 3 20 mV −40°C ≤ TA ≤ +125°C 40 mV Short-Circuit Current I V = V or GND 13 mA SC OUT SY Closed-Loop Output Impedance Z f = 1 kHz, G = 10 1 Ω OUT POWER SUPPLY Power Supply Rejection Ratio PSRR 1.8 V ≤ V ≤ 5.5 V 110 135 dB SY −40°C ≤ T ≤ +125°C 106 dB A Supply Current per Amplifier ISY ADA4051-2 VOUT = VSY/2 13 17 μA ADA4051-1 VOUT = VSY/2 15 18 μA −40°C ≤ T ≤ +125°C 20 μA A DYNAMIC PERFORMANCE Slew Rate SR+ RL = 10 kΩ, CL = 100 pF, G = 1 0.04 V/μs SR− R = 10 kΩ, C = 100 pF, G = 1 0.03 V/μs L L Settling Time t To 0.1%, V = 1 V p-p, 120 μs S IN RL = 10 kΩ, CL = 100 pF Gain Bandwidth Product GBP CL = 100 pF, G = 1 115 kHz Phase Margin ΦM CL = 100 pF, G = 1 40 Degrees Channel Separation CS V = 1.7 V, f = 100 Hz 140 dB IN NOISE PERFORMANCE Voltage Noise en p-p f = 0.1 Hz to 10 Hz 1.96 μV p-p Voltage Noise Density e f = 1 kHz 95 nV/√Hz n Current Noise Density i f = 1 kHz 100 fA/√Hz n Rev. B | Page 3 of 20 ADA4051-1/ADA4051-2 ELECTRICAL CHARACTERISTICS—5 V OPERATION VSY = 5.0 V, VCM = VSY/2 V, TA = 25°C, RL = 100 kΩ to GND, unless otherwise noted. Table 3. Parameter Symbol Test Conditions/Comments Min Typ Max Unit INPUT CHARACTERISTICS Offset Voltage VOS ADA4051-2 0 V ≤ VCM ≤ 5 V 2 15 μV ADA4051-1 0 V ≤ VCM ≤ 5 V 2 17 μV Offset Voltage Drift ∆V /∆T −40°C ≤ T ≤ +125°C 0.02 0.1 μV/°C OS A Input Bias Current I 20 70 pA B −40°C ≤ TA ≤ +125°C 200 pA Input Offset Current IOS 40 100 pA −40°C ≤ TA ≤ +125°C 150 pA Input Voltage Range −40°C ≤ T ≤ +125°C 0 5 V A Common-Mode Rejection Ratio CMRR 0 V ≤ V ≤ 5 V 110 135 dB CM −40°C ≤ T ≤ +125°C 106 dB A Large-Signal Voltage Gain AVO RL = 10 kΩ to VCM, 115 135 dB 0.1 V ≤ VOUT ≤ VSY − 0.1 V −40°C ≤ TA ≤ +125°C 106 dB Input Resistance R 8 MΩ IN Input Capacitance, Differential Mode C 2 pF INDM Input Capacitance, Common Mode CINCM 5 pF OUTPUT CHARACTERISTICS Output Voltage High V R = 100 kΩ to V 4.996 4.998 V OH L CM −40°C ≤ TA ≤ +125°C 4.985 V RL = 10 kΩ to VCM 4.96 4.99 V −40°C ≤ TA ≤ +125°C 4.9 V Output Voltage Low V R = 100 kΩ to V 1 4 mV OL L CM −40°C ≤ T ≤ +125°C 13 mV A R = 10 kΩ to V 9 30 mV L CM −40°C ≤ TA ≤ +125°C 90 mV Short-Circuit Current ISC VOUT = VSY or GND 15 mA Closed-Loop Output Impedance ZOUT f = 1 kHz, G = 10 1 Ω POWER SUPPLY Power Supply Rejection Ratio PSRR 1.8 V ≤ VSY ≤ 5.5 V 110 135 dB −40°C ≤ TA ≤ +125°C 106 dB Supply Current per Amplifier I SY ADA4051-2 V = V/2 13 17 μA OUT SY ADA4051-1 VOUT = VSY/2 15 18 μA −40°C ≤ TA ≤ +125°C 20 μA DYNAMIC PERFORMANCE Slew Rate SR+ RL = 10 kΩ, CL = 100 pF, G = 1 0.06 V/μs SR− RL = 10 kΩ, CL = 100 pF, G = 1 0.04 V/μs Settling Time tS To 0.1%, VIN = 1 V p-p, 110 μs R = 10 kΩ, C = 100 pF L L Gain Bandwidth Product GBP C = 100 pF, G = 1 125 kHz L Phase Margin Φ C = 100 pF, G = 1 40 Degrees M L Channel Separation CS VIN = 4.99 V, f = 100 Hz 140 dB NOISE PERFORMANCE Voltage Noise e p-p f = 0.1 Hz to 10 Hz 1.96 μV p-p n Voltage Noise Density en f = 1 kHz 95 nV/√Hz Current Noise Density in f = 1 kHz 100 fA/√Hz Rev. B | Page 4 of 20 ADA4051-1/ADA4051-2 ABSOLUTE MAXIMUM RATINGS THERMAL RESISTANCE Table 4. θ is specified for the worst-case conditions, that is, a device JA Parameter Rating soldered on a circuit board for surface-mount packages with its Supply Voltage 6 V exposed paddle soldered to a pad, if applicable. Table 5 shows Input Voltage ±V ± 0.3 V SY simulated thermal values for a 4-layer (2S2P) JEDEC standard 1 Input Current ±10 mA thermal test board, unless otherwise specified. 2 Differential Input Voltage ±VSY Output Short-Circuit Duration to GND Indefinite Table 5. Thermal Resistance Storage Temperature Range −65°C to +150°C Package Type θJA θJC Unit Operating Temperature Range −40°C to +125°C 5-Lead SOT-23 (RJ-5) 190 92 °C/W Junction Temperature Range −65°C to +150°C 5-Lead SC-70 (KS-5) 534 173 °C/W Lead Temperature (Soldering, 60 sec) 300°C 8-Lead MSOP (RM-8) 142 45 °C/W 1 8-Lead LFCSP (CP-8-2) 77 14 °C/W The input pins have clamp diodes to the power supply pins. Limit the input current to 10 mA or less whenever input signals exceed the power supply rail by 0.3 V. 2 Inputs are protected against high differential voltages by internal series POWER SEQUENCING 1.33 kΩ resistors and back-to-back diode-connected N-MOSFETs (with a The op amp supplies must be established simultaneously with typical VT of 0.7 V for VCM of 0 V). or before any input signals are applied. If this is not possible, the input current must be limited to 10 mA. Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any ESD CAUTION other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Rev. B | Page 5 of 20 ADA4051-1/ADA4051-2 TYPICAL PERFORMANCE CHARACTERISTICS TA = 25°C, unless otherwise noted. 300 300 V = 1.8V V = 5V SY SY V = V /2 V = V /2 CM SY CM SY 250 250 200 200 150 150 100 100 50 50 0 0 –10 –8 –6 –4 –2 0 2468 10 –10 –8 –6 –4 –2 02468 10 V (µV) V (µV) OS OS Figure 5. Input Offset Voltage Distribution Figure 8. Input Offset Voltage Distribution 8 10 V = 5V V = 1.8V SY SY –40°C ≤ T ≤ 125°C –40°C ≤ T ≤ +125°C A A 8 6 6 4 4 2 2 0 0 0 0.01 0.02 0.03 0.04 0.05 0.06 0.07 0.08 0.09 0.10 0 0.010.020.030.040.050.060.070.080.090.10 TCV (µV/°C) TCV (µV/°C) OS OS Figure 6. Input Offset Voltage Drift Distribution with Temperature Figure 9. Input Offset Voltage Drift Distribution with Temperature 15 15 V = 1.8V V = 5V SY SY 10 10 5 5 0 0 DEVICE 1 DEVICE 1 –5 DEVICE 2 –5 DEVICE 2 DEVICE 3 DEVICE 3 DEVICE 4 DEVICE 4 DEVICE 5 DEVICE 5 DEVICE 6 DEVICE 6 –10 –10 DEVICE 7 DEVICE 7 DEVICE 8 DEVICE 8 DEVICE 9 DEVICE 9 DEVICE 10 DEVICE 10 –15 –15 0 0.3 0.6 0.9 1.2 1.5 1.8 012345 V (V) V (V) CM CM Figure 7. Input Offset Voltage vs. Input Common-Mode Voltage Figure 10. Input Offset Voltage vs. Input Common-Mode Voltage Rev. B | Page 6 of 20 V (µV) NUMBER OF AMPLIFIERS OS NUMBER OF AMPLIFIERS 08056-003 08056-004 08056-002 NUMBER OF AMPLIFIERS NUMBER OF AMPLIFIERS V (µV) OS 08056-007 08056-005 08056-006 ADA4051-1/ADA4051-2 T = 25°C, unless otherwise noted. A 100 100 I V = 1.8V B+ V = 5V I SY SY B+ I B– I B– 80 80 60 60 40 40 20 20 0 0 –20 –20 25 50 75 100 125 25 50 75 100 125 TEMPERATURE (°C) TEMPERATURE (°C) Figure 11. Input Bias Current vs. Temperature Figure 14. Input Bias Current vs. Temperature 200 400 V = 1.8V V = 5V SY SY 150 300 100 200 50 100 0 0 –50 –100 I , 25°C I , 25°C B+ B+ –100 –200 I , 25°C I , 25°C B– B– I , 85°C I , 85°C B+ B+ I , 85°C I , 85°C B– B– –150 –300 I , 125°C I , 125°C B+ B+ I , 125°C I , 125°C B– B– –200 –400 0 0.3 0.6 0.9 1.2 1.5 1.8 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 V (V) V (V) CM CM Figure 12. Input Bias Current vs. Common-Mode Voltage and Temperature Figure 15. Input Bias Current vs. Common-Mode Voltage and Temperature 10,000 10,000 V = 1.8V SY V = 5V SY 1000 1000 100 100 10 10 1 1 0.1 –40°C 0.1 –40°C +25°C +25°C +85°C +85°C +125°C +125°C 0.01 0.01 0.001 0.01 0.1 1 10 0.001 0.01 0.1 1 10 100 LOAD CURRENT (mA) LOAD CURRENT (mA) Figure 13. Output Voltage (VOH) to Supply Rail vs. Load Current Figure 16. Output Voltage (VOH) to Supply Rail vs. Load Current and Temperature and Temperature Rev. B | Page 7 of 20 OUTPUT VOLTAGE (V ) TO SUPPLY RAIL (mV) OH I (pA) I (pA) B B 08056-009 08056-008 08056-010 OUTPUT VOLTAGE (V ) TO SUPPLY RAIL (mV) OH I (pA) I (pA) B B 08056-012 08056-011 08056-013 ADA4051-1/ADA4051-2 T = 25°C, unless otherwise noted. A 10,000 10,000 V = 1.8V V = 5V SY SY 1000 1000 100 100 10 10 1 1 0.1 –40°C 0.1 –40°C +25°C +25°C +85°C +85°C +125°C +125°C 0.01 0.01 0.001 0.01 0.1 1 10 100 0.001 0.01 0.1 1 10 100 LOAD CURRENT (mA) LOAD CURRENT (mA) Figure 17. Output Voltage (VOL) to Supply Rail vs. Load Current Figure 20. Output Voltage (VOL) to Supply Rail vs. Load Current and Temperature and Temperature 5000 1800 R = 100kΩ 4998 L R = 100kΩ L 1799 4996 4994 1798 4992 1797 R = 10kΩ R = 10kΩ L L 4990 1796 4988 4986 1795 4984 V = 1.8V V = 5V SY SY V = V /2 V = V /2 CM SY CM SY 1794 4982 –40 –25 –10 5 20 35 50 65 80 95 110 125 –40 –25 –10 5 20 35 50 65 80 95 110 125 TEMPERATURE (°C) TEMPERATURE (°C) Figure 18. Output Voltage (V ) vs. Temperature Figure 21. Output Voltage (V ) vs. Temperature OH OH 14 14 V = 1.8V SY V = 5V SY V = V /2 CM SY V = V /2 CM SY 12 12 10 10 R = 10kΩ L 8 8 6 6 4 4 R = 10kΩ L 2 2 R = 100kΩ L R = 100kΩ L 0 0 –40 –25 –10 5 20 35 50 65 80 95 110 125 –40 –25 –10 5 20 35 50 65 80 95 110 125 TEMPERATURE (°C) TEMPERATURE (°C) Figure 19. Output Voltage (V ) vs. Temperature Figure 22. Output Voltage (V ) vs. Temperature OL OL Rev. B | Page 8 of 20 OUTPUT VOLTAGE (V ) TO SUPPLY RAIL (mV) OUTPUT VOLTAGE [V ] (mV) OUTPUT VOLTAGE [V ] (mV) OL OL OH 08056-015 08056-016 08056-014 OUTPUT VOLTAGE [V ] (mV) OUTPUT VOLTAGE [V ] (mV) OUTPUT VOLTAGE (V ) TO SUPPLY RAIL (mV) OL OL OH 08056-019 08056-018 08056-017 ADA4051-1/ADA4051-2 T = 25°C, unless otherwise noted. A 30 30 V = V /2 ADA4051-2 CM SY ADA4051-1 25 25 20 20 15 15 10 10 ADA4051-2, 1.8V ADA4051-2, 5V 5 5 ADA4051-1, 1.8V V = V /2 CM SY ADA4051-1, 5V 0 0 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 –40 –25 –10 5 20 35 50 65 80 95 110 125 SUPPLY VOLTAGE (V) TEMPERATURE (°C) Figure 23. Total Supply Current vs. Supply Voltage Figure 26. Total Supply Current vs. Temperature 80 180 80 180 V = 5V V = 1.8V SY SY C = 100pF C = 100pF L L 60 135 60 135 40 90 40 90 PHASE PHASE 20 45 20 45 GAIN GAIN 0 0 0 0 –20 –45 –20 –45 –40 –90 –40 –90 –60 –135 –60 –135 100 1k 10k 100k 1M 100 1k 10k 100k 1M FREQUENCY (Hz) FREQUENCY (Hz) Figure 24. Open-Loop Gain and Phase vs. Frequency Figure 27. Open-Loop Gain and Phase vs. Frequency 50 50 V = 5V SY V = 1.8V SY R = 10kΩ L R = 10kΩ 40 40 L C = 50pF L C = 50pF L 30 30 20 20 10 10 0 0 –10 –10 –20 –20 –30 –30 G = 1 G = 1 –40 –40 G = 10 G = 10 G = 100 G = 100 –50 –50 100 1k 10k 100k 1M 100 1k 10k 100k 1M FREQUENCY (Hz) FREQUENCY (Hz) Figure 28. Closed-Loop Gain vs. Frequency Figure 25. Closed-Loop Gain vs. Frequency Rev. B | Page 9 of 20 OPEN-LOOP GAIN (dB) TOTAL SUPPLY CURRENT (µA) CLOSED-LOOP GAIN (dB) 08056-061 08056-020 PHASE (Degrees) 08056-022 OPEN-LOOP GAIN (dB) TOTAL SUPPLY CURRENT (µA) CLOSED-LOOP GAIN (dB) 08056-062 08056-023 PHASE (Degrees) 08056-025 ADA4051-1/ADA4051-2 T = 25°C, unless otherwise noted. A 10k 10k V = 1.8V V = 5V SY SY 1k 1k 100 100 10 10 1 1 G = −1 G = −1 G = −10 G = −10 G = −100 G = −100 0.1 0.1 1k 10k 100k 1M 1k 10k 100k 1M FREQUENCY (Hz) FREQUENCY (Hz) Figure 29. Output Impedance vs. Frequency Figure 32. Output Impedance vs. Frequency 110 110 V = 1.8V V = 5V SY SY 100 100 90 90 80 80 70 70 60 60 50 50 40 40 10 100 1k 10k 100k 1M 10 100 1k 10k 100k 1M FREQUENCY (Hz) FREQUENCY (Hz) Figure 30. CMRR vs. Frequency Figure 33. CMRR vs. Frequency 120 120 V = 1.8V V = 5V SY SY 100 100 80 80 60 60 PSRR+ PSRR+ 40 40 20 20 PSRR– PSRR– 0 0 100 1k 10k 100k 1M 100 1k 10k 100k 1M FREQUENCY (Hz) FREQUENCY (Hz) Figure 31. PSRR vs. Frequency Figure 34. PSRR vs. Frequency Rev. B | Page 10 of 20 PSRR (dB) CMRR (dB) Z (Ω) OUT 08056-028 08056-027 08056-026 PSRR (dB) CMRR (dB) Z (Ω) OUT 08056-031 08056-030 08056-029 ADA4051-1/ADA4051-2 T = 25°C, unless otherwise noted. A 60 60 V = ±0.9V SY V = ±2.5V SY V = 50mV p-p IN V = 50mV p-p IN R = 10kΩ L R = 10kΩ L C = 50pF 50 50 L C = 50pF L 40 40 −OVERSHOOT 30 30 20 20 −OVERSHOOT +OVERSHOOT +OVERSHOOT 10 10 0 0 10 100 10 100 LOAD CAPACITANCE (pF) LOAD CAPACITANCE (pF) Figure 35. Small-Signal Overshoot vs. Load Capacitance Figure 38. Small-Signal Overshoot vs. Load Capacitance V = 1.8V V = 5V SY SY R = 10kΩ R = 10kΩ L L C = 100pF C = 100pF L L G = 1 G = 1 V = 1.5V p-p V = 4V p-p IN IN TIME (100µs/DIV) TIME (100µs/DIV) Figure 39. Large-Signal Transient Response Figure 36. Large-Signal Transient Response V = 1.8V V = 5V SY SY R = 10kΩ R = 10kΩ L L C = 100pF C = 100pF L L G = 1 G = 1 V = 50mV p-p V = 50mV p-p IN IN TIME (100µs/DIV) TIME (100µs/DIV) Figure 37. Small-Signal Transient Response Figure 40. Small-Signal Transient Response Rev. B | Page 11 of 20 OVERSHOOT (%) VOLTAGE (10mV/DIV) VOLTAGE (500mV/DIV) 08056-033 08056-034 08056-032 OVERSHOOT (%) VOLTAGE (10mV/DIV) VOLTAGE (1V/DIV) 08056-037 08056-036 08056-035 ADA4051-1/ADA4051-2 T = 25°C, unless otherwise noted. A V = 1.8V V = 5V SY SY 1.96µV p-p 1.94µV p-p TIME (4s/DIV) TIME (4s/DIV) Figure 41. Input Voltage Noise, 0.1 Hz to 10 Hz Figure 44. Input Voltage Noise, 0.1 Hz to 10 Hz 1k 1k V = 1.8V V = 5V SY SY 100 100 10 10 1 1 10 100 1k 10k 10 100 1k 10k FREQUENCY (Hz) FREQUENCY (Hz) Figure 42. Voltage Noise Density vs. Frequency Figure 45. Voltage Noise Density vs. Frequency 0.15 0.4 V = ±0.9V SY V = ±2.5V SY G = –10 G = –10 0.10 0.3 0.05 0.2 INPUT VOLTAGE 0 0.1 INPUT VOLTAGE –0.05 0.5 0 1 OUTPUT VOLTAGE OUTPUT VOLTAGE 0 0 –0.1 –0.5 –1 –1.0 –2 –1.5 –3 TIME (40µs/DIV) TIME (40µs/DIV) Figure 43. Positive Overload Recovery Figure 46. Positive Overload Recovery Rev. B | Page 12 of 20 INPUT VOLTAGE (50mV/DIV) VOLTAGE NOISE DENSITY (nV/√Hz) INPUT VOLTAGE NOISE (0.5µV/DIV) 08056-038 08056-039 OUTPUT VOLTAGE (500mV/DIV) 08056-040 INPUT VOLTAGE (100mV/DIV) VOLTAGE NOISE DENSITY (nV/√Hz) INPUT VOLTAGE NOISE (0.5µV/DIV) 08056-041 OUTPUT VOLTAGE (1V/DIV) 08056-042 08056-043 ADA4051-1/ADA4051-2 T = 25°C, unless otherwise noted. A 0.05 0.1 INPUT VOLTAGE 0 0 INPUT VOLTAGE –0.05 –0.1 4 –0.10 –0.2 1.5 3 –0.15 –0.3 1.0 2 –0.4 0.5 1 OUTPUT VOLTAGE OUTPUT VOLTAGE 0 0 V = ±0.9V V = ±2.5V SY SY G = –10 G = –10 –0.5 –1 TIME (40µs/DIV) TIME (40µs/DIV) Figure 47. Negative Overload Recovery Figure 50. Negative Overload Recovery INPUT VOLTAGE INPUT VOLTAGE 5 5 OUTPUT VOLTAGE OUTPUT VOLTAGE ERROR ERROR 0 0 BAND BAND –5 –5 V = ±0.9V V = ±2.5V SY SY V = 1V p-p V = 1V p-p IN IN R = 10kΩ R = 10kΩ L L C = 100pF C = 100pF L L TIME (40µs/DIV) TIME (40µs/DIV) Figure 48. Positive Settling Time to 0.1% Figure 51. Positive Settling Time to 0.1% INPUT VOLTAGE INPUT VOLTAGE 5 5 OUTPUT VOLTAGE OUTPUT VOLTAGE ERROR ERROR 0 0 BAND BAND –5 –5 V = ±2.5V V = ±0.9V SY SY V = 1V p-p V = 1V p-p IN IN R = 10kΩ R = 10kΩ L L C = 100pF C = 100pF L L TIME (40µs/DIV) TIME (40µs/DIV) Figure 49. Negative Settling Time to 0.1% Figure 52. Negative Settling Time to 0.1% Rev. B | Page 13 of 20 INPUT VOLTAGE (50mV/DIV) INPUT VOLTAGE (500mV/DIV) INPUT VOLTAGE (500mV/DIV) OUTPUT VOLTAGE (5mV/DIV) OUTPUT VOLTAGE (5mV/DIV) 08056-045 08056-046 OUTPUT VOLTAGE (500mV/DIV) 08056-044 INPUT VOLTAGE (100mV/DIV) INPUT VOLTAGE (500mV/DIV) INPUT VOLTAGE (500mV/DIV) OUTPUT VOLTAGE (5mV/DIV) OUTPUT VOLTAGE (5mV/DIV) 08056-049 08056-048 OUTPUT VOLTAGE (1V/DIV) 08056-047 ADA4051-1/ADA4051-2 T = 25°C, unless otherwise noted. A –100 –100 V = 1V 100kΩ V = 0.5V IN IN 100kΩ V = 3V V = 1V IN IN V = 4.99V 1kΩ V = 1.7V IN IN 1kΩ –110 –110 –120 –120 –130 –130 –140 –140 V = 1.8V SY V = 5V SY G = –100 G = –100 R = 10kΩ L R = 10kΩ L C = 50pF L C = 50pF L –150 –150 20 200 2k 20k 20 200 2k 20k FREQUENCY (Hz) FREQUENCY (Hz) Figure 53. Channel Separation vs. Frequency Figure 56. Channel Separation vs. Frequency 6 1.8 5 1.5 1.2 4 0.9 3 0.6 2 V = 5V V = 1.8V SY SY V = 4.9V V = 1.7V IN 0.3 1 IN G = 1 G = 1 R = 10kΩ R = 10kΩ L L C = 50pF C = 50pF L L 0 0 100 1k 10k 100k 100 1k 10k 100k FREQUENCY (Hz) FREQUENCY (Hz) Figure 54. Output Swing vs. Frequency Figure 57. Output Swing vs. Frequency V = ±0.9V V = ±2.5V SY SY G = 1 G = 1 R = NO LOAD R = NO LOAD L L C = NO LOAD C = NO LOAD L L V OUT V OUT V IN V IN TIME (200µs/DIV) TIME (200µs/DIV) Figure 55. No Phase Reversal Figure 58. No Phase Reversal Rev. B | Page 14 of 20 OUTPUT SWING (V) CHANNEL SEPARATION (dB) VOLTAGE (500mV/DIV) 08056-052 08056-051 08056-050 OUTPUT SWING (V) CHANNEL SEPARATION (dB) VOLTAGE (1V/DIV) 08056-055 08056-053 08056-054 ADA4051-1/ADA4051-2 THEORY OF OPERATION pole-zero doublets. This design prevents any instability introduced The ADA4051-1/ADA4051-2 micropower chopper operational by the ACFB in the overall feedback loop. amplifiers feature a novel, patent-pending technique that sup- presses offset-related ripple in a chopper amplifier. Instead of filtering the ripple in the ac domain, this technique nulls the CHOP1 Gm1 CHOP2 C2 Gm2 Gm3 amplifier’s initial offset in the dc domain, thus preventing ripple +IN OUT at the overall output. –IN Auto-zeroing and chopping are two techniques widely used in C1 C3 high precision CMOS amplifiers to achieve low offset, low offset drift, and no 1/f noise. Each of these techniques has pros and Gm5 NF CHOP3 Gm4 cons. Auto-zeroing results in more in-band noise due to aliasing Gm6 (= Gm1) introduced by sampling. On the other hand, chopping produces offset-related ripple because it modulates the initial offset associated with the amplifier up to its chopping frequency. Figure 59. ADA4051-1/ADA4051-2 Chopper Amplifiers Block Diagram To accomplish the best noise vs. power trade-off, the chopping The voltage noise density, which is equal to the thermal noise technique is the better approach when designing a low offset floor dominated by the Gm1, is essentially flat from dc to the amplifier because there is no increased in-band noise. It is chopping frequency because CHOP1 and CHOP2 eliminate the preferable to suppress the offset-related ripple inside a chopper 1/f noise generated in Gm1 and the ACFB does not contribute amplifier because the offset-related ripple would otherwise need any additional noise. Although the ACFB suppresses the ripple to be eliminated by an extra off-chip postfilter. related to the chopping, there is a remaining voltage ripple. To further suppress the remaining ripple down to a desired level, it Figure 59 shows the block diagram design of the ADA4051-1/ is recommended to have a postfilter at the output of the amplifier. ADA4051-2 chopper amplifiers employing a local feedback loop called autocorrection feedback (ACFB). The main signal path The remaining voltage ripple originates from two sources. The contains an input chopping switch network (CHOP1), a first first type of ripple is due to the residual ripple associated with transconductance amplifier (Gm1), an output chopping switch the initial offset of the Gm1. It is proportional to the magnitude network (CHOP2), a second transconductance amplifier (Gm2), of the initial offset and creates a spectrum at the chopping and a third transconductance amplifier (Gm3). CHOP1 and frequency (f ). When the amplifier is configured as a unity- CHOP CHOP2 operate at 40 kHz of chopping frequency to modulate gain buffer, this ripple has a typical value of 4.9 μV rms and a the initial offset and 1/f noise from Gm1 up to the chopping maximum of 34.7 μV rms. The second type of ripple is due to frequency. A fourth transconductance amplifier (Gm4) in the the intermodulation between the high frequency input signal ACFB senses the modulated ripple at the output of CHOP2, and the chopping frequency. This ripple depends on the input caused by the initial offset voltage of Gm1. Then, the ripple is frequency (fIN) and creates a spectrum at frequencies equal to demodulated down to a dc domain through a third chopping the difference between the chopping frequency and the input switch network (CHOP3), operating with the same chopping frequency (fCHOP − fIN), as well as at frequencies equal to the clock as CHOP1 and CHOP2. Finally, a null transconductance summation of the chopping frequency and the input frequency amplifier (Gm5) tries to null any dc component at the output of (f + f ). The magnitude of the ripple for different input CHOP IN Gm1 that would otherwise appear in the overall output as ripple. frequencies is shown in Figure 60. 500 A switched-capacitor notch filter (NF) functions to selectively suppress the undesired offset-related ripple without disturbing the desired input signal from the overall input. The desired input 400 dc signal appears as a dc signal at the output of CHOP2. Then, the initial offset is modulated up to the chopping frequency by 300 CHOP3 and filtered out by the NF. Therefore, initial offset does not create any feedback and does not disturb the desired input 200 signal. The NF is synchronized with the chopping clock to filter out the modulated component. In the same manner, the offset of Gm5 is filtered out by the combination of CHOP3 and the 100 NF, enabling accurate ripple sensing at the output of CHOP2. In parallel with the high dc gain path, a feedforward transcon- 0 0123456789 10 ductance amplifier (Gm6) is added to bypass the phase shift INPUT FREQUENCY (kHz) introduced by the ACFB at the chopping frequency. Gm6 is Figure 60. ADA4051-1/ADA4051-2 Modulated Output Ripple vs. Input Frequency designed to have the same transconductance as Gm1 to avoid Rev. B | Page 15 of 20 MODULATED OUTPUT RIPPLE (µV rms) 08056-063 08056-060 ADA4051-1/ADA4051-2 The design architecture of the ADA4051-1/ADA4051-2 The ADA4051-1/ADA4051-2 also have internal circuitry that specifically targets precision signal conditioning applications protects the input stage from high differential voltages. This requiring accurate and stable performance from dc to 10 Hz circuitry is composed of internal 1.33 kΩ resistors in series with each input and back-to-back diode-connected N-MOSFET (with a bandwidth. In summary, the main features of the ADA4051-1/ ADA4051-2 chopper amplifiers are typical VT of 0.7 V for a VCM of 0 V) after these series resistors. With normal negative feedback operating conditions, the ADA4051-1/ • Considerable suppression of the offset-related ripple ADA4051-2 amplifiers correct their output to ensure that the two • No affect on the desired input signal as long as its inputs are at the same voltage. However, if the device is configured frequency is much lower than the chopping frequency as a comparator or there are unusual operating conditions, the shown in Figure 60 input voltages can be forced to different potentials, which may • Achievement of low offset similar to a conventional cause excessive current to flow through the internal diode- chopper amplifier connected N-MOSFETs. • No introduction of excess noise Although the ADA4051-1/ADA4051-2 are rail-to-rail input The ADA4051-1/ADA4051-2 chopper amplifiers provide a rail- amplifiers, take care to ensure that the potential difference to-rail input range with a 1.8 V to 5.5 V supply voltage range and between the inputs does not exceed ±VSY to avert permanent 20 μA supply current consumption over the −40°C to +125°C damage to the device. extended industrial temperature range. The gain bandwidth is OUTPUT PHASE REVERSAL 125 kHz as a unity-gain stable amplifier up to 100 pF load Although output phase reversal can occur with other amplifiers capacitance. when the input common-mode voltage range is exceeded, the INPUT VOLTAGE RANGE ADA4051-1/ADA4051-2 amplifiers are designed to prevent The ADA4051-1/ADA4051-2 have internal ESD protection diodes. any output phase reversal, provided both inputs are maintained These diodes are connected between the inputs and each supply approximately within 0.3 V above and below the supply voltages rail to protect the input MOSFETs from an electrical discharge (±V ± 0.3 V). SY event and are reversed-biased during normal operation. This With other amplifiers, the outputs may jump in the opposite protection scheme allows voltages as high as approximately 0.3 V direction to the supply rail when a common-mode voltage beyond the supplies (±V ± 0.3 V) to be applied at the input of SY moves outside the common-mode range. This usually occurs either terminal without causing permanent damage. when one of the internal stages of the amplifier no longer has If either input exceeds one of the supply rails by more than 0.3 V, sufficient bias voltage across it and subsequently turns off. these ESD diodes become forward-biased and large amounts of However, with the ADA4051-1/ADA4051-2 amplifiers, if one current begin to flow through them. Without current limiting, this or both inputs exceed the input voltage range but remain within excessive current would cause permanent damage to the device. the ±VSY ± 0.3 V range, an internal loop opens and the output If the inputs are expected to be subject to overvoltage conditions, remains in saturation mode, without phase reversal, until the install a resistor in series with each input to limit the input current input voltage is brought back to within the input voltage range to 10 mA maximum. limits as shown in Figure 55 and Figure 58. Rev. B | Page 16 of 20 ADA4051-1/ADA4051-2 OUTLINE DIMENSIONS 3.00 2.90 2.80 5 4 3.00 1.70 2.80 1.60 2.60 1.50 12 3 0.95 BSC 1.90 BSC 1.30 1.15 0.90 0.20 MAX 1.45 MAX 0.08 MIN 0.95 MIN 0.55 0.15 MAX 10° 0.45 SEATING 0.20 0.05 MIN 5° 0.50 MAX 0.35 PLANE BSC 0° 0.35 MIN COMPLIANT TO JEDEC STANDARDS MO-178-AA Figure 61. 5-Lead Small Outline Transistor Package [SOT-23] (RJ-5) Dimensions shown in millimeters 2.20 2.00 1.80 2.40 1.35 5 4 2.10 1.25 1.80 1.15 12 3 0.65 BSC 1.00 0.40 1.10 0.90 0.10 0.80 0.70 0.46 0.22 SEATING 0.10 MAX 0.36 0.30 PLANE 0.08 COPLANARITY 0.26 0.15 0.10 COMPLIANT TO JEDEC STANDARDS MO-203-AA Figure 62. 5-Lead Thin Shrink Small Outline Transistor Package [SC-70] (KS-5) Dimensions shown in millimeters Rev. B | Page 17 of 20 072809-A 121608-A ADA4051-1/ADA4051-2 3.20 3.00 2.80 8 5 5.15 3.20 4.90 3.00 4.65 1 2.80 4 PIN 1 IDENTIFIER 0.65 BSC 0.95 15° MAX 0.85 1.10 MAX 0.75 0.80 0.15 0.23 6° 0.55 0.40 0.05 0.09 0° 0.40 0.25 COPLANARITY 0.10 COMPLIANT TO JEDEC STANDARDS MO-187-AA Figure 63. 8-Lead Mini Small Outline Package [MSOP] (RM-8) Dimensions shown in millimeters 3.25 0.60 MAX 3.00 SQ 0.50 2.75 BSC 0.60 MAX 5 8 2.95 1.60 EXPOSED 2.75 SQ TOP PIN 1 1.45 PAD VIEW 2.55 INDICATOR (BOTTOM VIEW) 1.30 4 1 PIN 1 0.50 INDICATOR 1.89 0.40 1.74 12° MAX 0.70 MAX 0.30 1.59 0.90 MAX 0.65 TYP 0.85 NOM 0.05 MAX FOR PROPER CONNECTION OF 0.01 NOM THE EXPOSED PAD, REFER TO THE PIN CONFIGURATION AND 0.30 SEATING FUNCTION DESCRIPTIONS PLANE 0.23 0.20 REF SECTION OF THIS DATA SHEET. 0.18 Figure 64. 8-Lead Lead Frame Chip Scale Package [LFCSP_VD] 3 mm × 3 mm Body, Very Thin, Dual Lead (CP-8-2) Dimensions shown in millimeters ORDERING GUIDE 1 Model Temperature Range Package Description Package Option Branding ADA4051-1ARJZ-R2 −40°C to +125°C 5-Lead SOT-23 RJ-5 A0U ADA4051-1ARJZ-R7 −40°C to +125°C 5-Lead SOT-23 RJ-5 A0U ADA4051-1ARJZ-RL −40°C to +125°C 5-Lead SOT-23 RJ-5 A0U ADA4051-1AKSZ-R2 −40°C to +125°C 5-Lead SC-70 KS-5 A0U ADA4051-1AKSZ-R7 −40°C to +125°C 5-Lead SC-70 KS-5 A0U ADA4051-1AKSZ-RL −40°C to +125°C 5-Lead SC-70 KS-5 A0U ADA4051-2ACPZ-R2 −40°C to +125°C 8-Lead LFCSP_VD CP-8-2 A2M ADA4051-2ACPZ-R7 −40°C to +125°C 8-Lead LFCSP_VD CP-8-2 A2M ADA4051-2ACPZ-RL −40°C to +125°C 8-Lead LFCSP_VD CP-8-2 A2M ADA4051-2ARMZ −40°C to +125°C 8-Lead MSOP RM-8 A2M ADA4051-2ARMZ-R7 −40°C to +125°C 8-Lead MSOP RM-8 A2M ADA4051-2ARMZ-RL −40°C to +125°C 8-Lead MSOP RM-8 A2M 1 Z = RoHS Compliant Part. Rev. B | Page 18 of 20 100709-B 090308-B ADA4051-1/ADA4051-2 NOTES Rev. B | Page 19 of 20 ADA4051-1/ADA4051-2 NOTES ©2009–2010 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D08056-0-1/10(B) Rev. B | Page 20 of 20
Frequently asked questions
What makes Elite.Parts unique?
What kind of warranty will the ADA4051-1 have?
Which carriers does Elite.Parts work with?
Will Elite.Parts sell to me even though I live outside the USA?
I have a preferred payment method. Will Elite.Parts accept it?
Why buy from GID?
Quality
We are industry veterans who take pride in our work
Protection
Avoid the dangers of risky trading in the gray market
Access
Our network of suppliers is ready and at your disposal
Savings
Maintain legacy systems to prevent costly downtime
Speed
Time is of the essence, and we are respectful of yours
Manufacturers


What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods