Elite.Parts Manufacturers A ANALOG DEVICES AD9861-80
About product Specifications Features Datasheet FAQ

ANALOG DEVICES AD9861-80

Description

Analog Devices AD9861 10-Bit Mixed-Signal Front-End (MXFE) Processor

Part Number

AD9861-80

Price

Request Quote

Manufacturer

ANALOG DEVICES

Lead Time

Request Quote

Category

PRODUCTS - A

Specifications

# Chan

2

ADC Bits x #ADCs-Speed

10x2-50 MHz,10x2-80 MHz

DAC Bits x #DACs-ClkSpeed

10x2-200 MHz

Pkg Type

CSP

Primary Application

Broadband Wireless

Resolution (Bits)

10bit

Sample Rate

80MSPS

Supply V

Single(+3),Single(+3.3)

Throughput Rate

80MSPS

Features

Datasheet

pdf file

AD9861-2046465111.pdf

1282 KiB

Extracted Text

™ Mixed-Signal Front-End (MxFE ) Baseband Transceiver for Broadband Applications AD9861 FEATURES FUNCTIONAL BLOCK DIAGRAM Receive path includes dual 10-bit analog-to-digital VIN+A ADC converters with internal or external reference, 50 MSPS DATA Rx DATA VIN–A MUX and 80 MSPS versions AND VIN+B LATCH ADC Transmit path includes dual 10-bit, 200 MSPS digital-to- VIN–B I/O analog converters with 1×, 2×, or 4× interpolation and INTERFACE I/O CONTROL INTERFACE programmable gain control CONFIGURATION FLEXIBLE LOW-PASS BLOCK Internal clock distribution block includes a programmable I/O BUS INTERPOLATION [0:19] FILTER phase-locked loop and timing generation circuitry, IOUT+A DATA DAC allowing single-reference clock operation IOUT–A LATCH AND 20-pin flexible I/O data interface allows various interleaved IOUT+B DEMUX Tx DATA DAC or noninterleaved data transfers in half-duplex mode and IOUT–B interleaved data transfers in full-duplex mode AUX Configurable through register programmability or ADC optionally limited programmability through mode pins AUX Independent Rx and Tx power-down control pins DAC ADC CLOCK CLKIN 64-lead LFCSP package (9 mm × 9 mm footprint) AUX 3 configurable auxiliary converter pins DAC DAC CLOCK PLL APPLICATIONS AUX ADC Broadband access AD9861 Broadband LAN AUX DAC Communications (modems) 03606-0-001 Figure 1. GENERAL DESCRIPTION of custom digital back ends or open market DSPs. The AD9861 is a member of the MxFE family—a group of integrated converters for the communications market. The In half-duplex systems, the interface supports 20-bit parallel AD9861 integrates dual 10-bit analog-to-digital converters transfers or 10-bit interleaved transfers. In full-duplex systems, (ADC) and dual 10-bit digital-to-analog converters (TxDAC®). the interface supports an interleaved 10-bit ADC bus and an Two speed grades are available, -50 and -80. The -50 is opti- interleaved 10-bit TxDAC bus. The flexible I/O bus reduces pin mized for ADC sampling of 50 MSPS and less, while the -80 is count and, therefore, reduces the required package size on the optimized for ADC sample rates between 50 MSPS and 80 MSPS. AD9861 and the device to which it connects. The dual TxDACs operate at speeds up to 200 MHz and include a bypassable 2× or 4× interpolation filter. Three The AD9861 can use either mode pins or a serial program- auxiliary converters are also available to provide required mable interface (SPI) to configure the interface bus, operate the system level control voltages or to monitor system signals. The ADC in a low power mode, configure the TxDAC interpolation AD9861 is optimized for high performance, low power, small rate, and control ADC and TxDAC power-down. The SPI form factor, and to provide a cost-effective solution for the provides more programmable options for both the TxDAC path broadband communication market. (for example, coarse and fine gain control and offset control for channel matching) and the ADC path (for example, the internal The AD9861 uses a single input clock pin (CLKIN) to generate duty cycle stabilizer, and twos complement data format). all system clocks. The ADC and TxDAC clocks are generated within a timing generation block that provides user programma- The AD9861 is packaged in a 64-lead LFCSP (low profile, fine ble options such as divide circuits, PLL multipliers, and switches. pitched, chip scale package). The 64-lead LFCSP footprint is only 9 mm × 9 mm, and is less than 0.9 mm high, fitting into A flexible, bidirectional 20-bit I/O bus accommodates a variety tightly spaced applications such as PCMCIA cards Rev. 0 Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Specifications subject to change without notice. No license is granted by implication Tel: 781.329.4700 www.analog.com or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. Fax: 781.326.8703 © 2003 Analog Devices, Inc. All rights reserved. AD9861 TABLE OF CONTENTS Tx Path Specifications...................................................................... 3 Theory of Operation ...................................................................... 22 Rx Path Specifications...................................................................... 4 System Block ............................................................................... 22 Power Specifications......................................................................... 5 Rx Path Block.............................................................................. 22 Digital Specifications........................................................................ 5 Tx Path Block.............................................................................. 24 Timing Specifications....................................................................... 6 Auxiliary Converters.................................................................. 27 Absolute Maximum Ratings............................................................ 7 Digital Block................................................................................ 30 ESD Caution.................................................................................. 7 Programmable Registers............................................................ 42 Pin Configuration and Pin Function Descriptions...................... 8 Clock Distribution Block .......................................................... 45 Typical Performance Characteristics ........................................... 10 Outline Dimensions ....................................................................... 49 Terminology .................................................................................... 21 Ordering Guide .......................................................................... 50 REVISION HISTORY Revision 0: Initial Version Rev. 0 | Page 2 of 52 AD9861 Tx PATH SPECIFICATIONS Table 1. AD9861-50 and AD9861-80 1 FDAC = 200 MSPS; 4× interpolation; RSET = 4.02 kΩ; differential load resistance of 100 Ω ; TxPGA = 20 dB, AVDD = DVDD = 3.3 V, unless otherwise noted Parameter Temp Test Level Min Typ Max Unit Tx PATH GENERAL Resolution Full IV 10 Bits Maximum DAC Update Rate Full IV 200 MHz Maximum Full-Scale Output Current Full IV 20 mA Full-Scale Error Full V 1% Gain Mismatch Error 25°C IV –3.5 +3.5 % FS Offset Mismatch Error Full IV –0.1 +0.1 % FS Reference Voltage Full V 1.23 V Output Capacitance Full V 5 pF Phase Noise (1 kHz Offset, 6 MHz Tone) 25°C V –115 dBc/Hz Output Voltage Compliance Range Full IV –1.0 +1.0 V TxPGA Gain Range Full V 20 dB TxPGA Step Size Full V 0.10 dB Tx PATH DYNAMIC PERFORMANCE (I = 20 mA; F = 1 MHz) OUTFS OUT SNR Full IV 60.2 60.8 dB SINAD Full IV 59.7 60.7 dB THD Full IV −77.5 −65.8 dBc SFDR, Wideband (DC to Nyquist) Full IV 64.6 76.0 dBc SFDR, Narrowband (1 MHz Window) Full IV 72.5 81.0 dBc 1 See Figure 2 for description of the TxDAC termination scheme. TxDAC 50Ω 50Ω 03606-0-030 Figure 2. Diagram Showing Termination of 100 Ω Differential Load for Some TxDAC Measurements Rev. 0 | Page 3 of 52 AD9861 Rx PATH SPECIFICATIONS Table 2. AD9861-50 and AD9861-80 FADC = 50 MSPS for the AD9861-50, 80 MSPS for the AD9861-80; internal reference; differential analog inputs, ADC_AVDD = DVDD = 3.3V, unless otherwise noted Parameter Temp Test Level Min Typ Max Unit Rx PATH GENERAL Resolution Full V 10 Bits Maximum ADC Sample Rate Full IV 50/80 MSPS Gain Mismatch Error Full V % FS ±0.2 Offset Mismatch Error Full V % FS ±0.1 Reference Voltage Full V 1.0 V Reference Voltage (REFT–REFB) Error Full IV –30 +30 mV ±6 Input Resistance (Differential) Full V 2 kΩ Input Capacitance Full V 5 pF Input Bandwidth Full V 30 MHz Differential Analog Input Voltage Range Full V 2 V p-p differential Rx PATH DC ACCURACY Integral Nonlinearity (INL) 25°C V LSB ±0.75 Differential Nonlinearity (DNL) 25°C V LSB ±0.75 Aperature Delay 25°C V 2.0 ns Aperature Uncertainty (Jitter) 25°C V 1.2 ps rms Input Referred Noise 25°C V 450 uV AD9861-50 Rx PATH DYNAMIC PERFORMANCE (V = –0.5 dBFS; F = 10 MHz) IN IN SNR Full IV 55.5 60 dBc SINAD Full IV 55.6 60 dBc SINAD 25°C IV 58.5 60 dBc THD (Second to Ninth Harmonics) Full IV −71.5 −64.6 dBc SFDR, Wideband (DC to Nyquist) Full IV 65.7 73.5 dBc Crosstalk between ADC Inputs Full V 80 dB AD9861-80 Rx PATH DYNAMIC PERFORMANCE (V = –0.5 dBFS; F = 10 MHz) IN IN SNR Full IV 55.4 59.5 dBc SINAD Full IV 52.7 59.0 dBc THD (Second to Ninth Harmonics) Full IV −67 dBc SFDR, Wideband (DC to Nyquist) Full IV 67 dBc Crosstalk between ADC Inputs Full V 80 dB Rev. 0 | Page 4 of 52 AD9861 POWER SPECIFICATIONS Table 3. AD9861-50 and AD9861-80 Analog and digital supplies = 3.3 V; FCLKIN = 50 MHz; PLL 4× setting; normal timing mode Parameter Temp Test Level Min Typ Max Unit POWER SUPPLY RANGE Analog Supply Voltage (AVDD) Full IV 2.7 3.6 V Digital Supply Voltage (DVDD) Full IV 2.7 3.6 V Full IV 2.7 3.6 V Driver Supply Voltage (DRVDD) ANALOG SUPPLY CURRENTS TxPath (20 mA Full-Scale Outputs) Full V 70 mA TxPath (2 mA Full-Scale Outputs) Full V 20 mA Rx Path (-80, at 80 MSPS) Full V 165 mA RxPath (-80, at 40 MSPS, Low Power Mode) Full V 82 mA RxPath (-80, at 20 MSPS, Ultralow Power Mode) Full V 35 mA Rx Path (-50, at 50 MSPS) Full V 103 mA RxPath (-50, at 50 MSPS, Low Power Mode) Full V 69 mA RxPath (-50, at 16 MSPS, Ultralow Power Mode) Full V 28 mA TxPath, Power-Down Mode Full V 2 mA RxPath, Power-Down Mode Full V 5 mA PLL Full V 12 mA DIGITAL SUPPLY CURRENTS TxPath, 1× Interpolation, Full V 20 mA 50 MSPS DAC Update for Both DACs, Half-Duplex 24 Mode TxPath, 2× Interpolation, Full V 50 mA 100 MSPS DAC Update for Both DACs, Half-Duplex 24 Mode TxPath, 4× Interpolation, Full V 80 mA 200 MSPS DAC Update for Both DACs, Half-Duplex 24 Mode RxPath Digital, Half-Duplex 24 Mode Full V 15 mA DIGITAL SPECIFICATIONS Table 4. AD9861-50 and AD9861-80 Parameter Temp Test Level Min Typ Max Unit LOGIC LEVELS Input Logic High Voltage, VIH Full IV DRVDD – 0.7 V Input Logic Low Voltage, V Full IV 0.4 V IL Output Logic High Voltage, V (1 mA Load) Full IV DRVDD – 0.6 V OH Output Logic Low Voltage, V (1 mA Load) Full IV 0.4 V OL DIGITAL PIN Input Leakage Current Full IV 12 µA Input Capacitance Full IV 3 pF Minimum RESET Low Pulse Width Full IV 5 Input Clock Cycles Digital Output Rise/Fall Time Full IV 2.8 4 ns Rev. 0 | Page 5 of 52 AD9861 TIMING SPECIFICATIONS Table 5. AD9861-50 and AD9861-80 Parameter Temp Test Level Min Typ Max Unit INPUT CLOCK CLKIN Clock Rate (PLL Bypassed) Full IV 1 200 MHz PLL Input Frequency Full IV 16 200 MHz PLL Ouput Frequency Full IV 32 350 MHz TxPATH DATA Full V 5 Setup Time (HD20 Mode, Time Required Before Data Latching ns (see Clock Edge) Distribution Block section) Hold Time (HD20 Mode, Time Required After Data Latching Full V –1.5 ns (see Clock Edge) Distribution Block section) Latency 1× Interpolation (data in until peak output response) Full V 7 DAC Clock Cycles Latency 2× Interpolation (data in until peak output response) Full V 35 DAC Clock Cycles Latency 4× Interpolation (data in until peak output response) Full V 83 DAC Clock Cycles RxPATH DATA Output Delay (HD20 Mode, tOD) Full V –1.5 ns (see Clock Distribution Block section) Latency Full V 5 ADC Clock Cycles Table 6. Explanation of Test Levels Level Description I 100% production tested. II 100% production tested at 25°C and guaranteed by design and characterization at specified temperatures. III Sample tested only. IV Parameter is guaranteed by design and characterization testing. V Parameter is a typical value only. VI 100% production tested at 25°C and guaranteed by design and characterization for industrial temperature range. Rev. 0 | Page 6 of 52 AD9861 ABSOLUTE MAXIMUM RATINGS Table 7. Thermal Resistance Parameter Rating 64-lead LFCSP (4-layer board): Electrical θJA = 24.2 (paddle soldered to ground plan, 0 LPM Air) AVDD Voltage 3.9 V max θJA = 30.8 (paddle not soldered to ground plan, 0 LPM Air) DRVDD Voltage 3.9 V max Analog Input Voltage –0.3 V to AVDD + 0.3 V Digital Input Voltage –0.3 V to DVDD – 0.3 V Digital Output Current 5 mA max Environmental Operating Temperature Range –40°C to +85°C (Ambient) Maximum Junction Temperature 150°C Lead Temperature (Soldering, 10 sec) 300°C Storage Temperature Range –65°C to +150°C (Ambient) Stresses above those listed under the Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ESD CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although this product features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. Rev. 0 | Page 7 of 52 AD9861 PIN CONFIGURATION AND PIN FUNCTION DESCRIPTIONS 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 SPI_DIO 1 48 CLKIN SPI_CLK 2 47 AUXADC_REF SPI_SDO/AUX_SPI_SDO 3 46 RESET ADC_LO_PWR/AUX_SPI_CS 4 45 AUX_DACC/AUX_ADCB DVDD 5 44 L0 DVSS 6 43 L1 AD9861 AVDD 7 42 L2 TOP VIEW IOUT–A 8 41 L3 (Not to Scale) IOUT+A 9 40 L4 AGND 10 39 L5 REFIO 11 38 L6 FSADJ 12 37 L7 AGND 13 36 L8 IOUT+B 14 35 L9 IOUT–B 15 34 AUX_SPI_CLK AVDD 16 33 IFACE1 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 03606-0-019 Figure 3. Pin Configuration Table 8. Pin Function Descriptions 1 2, 3 Pin No. Name Description 1 SPI_DIO SPI: Serial Port Data Input. (Interp1) No SPI: Tx Interpolation Pin, MSB. 2 SPI_CLK SPI: Serial Port Shift Clock. (Interp0) No SPI: Tx Interpolation Pin, LSB. 3 SPI_SDO/AUXSPI_SDO SPI: 4-Wire Serial Port Data Output/Data Output Pin for AuxSPI. (FD/HD) No SPI: Configures Full-Duplex or Half-Duplex Mode. 4 ADC_LO_PWR/AUX_SPI_CS ADC Low Power Mode Enable. Defined at power-up. CS for AuxSPI. 5, 31 DVDD Digital Supply. 6, 32 DVSS Digital Ground. 7, 16, 50, 51, 61 AVDD Analog Supply. 8, 9 IOUT–A, IOUT+A DAC A Differential Output. 10, 13, 49, 53, 59 AGND, AVSS Analog Ground. 11 REFIO Tx DAC Band Gap Reference Decoupling Pin. 12 FSADJ Tx DAC Full-Scale Adjust Pin. 14, 15 IOUT+B, IOUT−B DAC B Differential Output. 17 IFACE2 SPI: Buffered CLKIN. Can be configured as system clock output. (10/20) No SPI: For FD: Buffered CLKIN; For HD20 or HD10 : 10/20 Configuration Pin. 18 IFACE3 Clock Output. 19–28 U9–U0 Upper Data Bit 9 to Upper Data Bit 0. 29 AUX1 Configurable as either AuxADC_A2 or AuxDAC_A. 30 AUX2 Configurable as either AuxADC_A1 or AuxDAC_B. 33 IFACE1 SPI: For FD: TxSYNC; For HD20, HD10, or Clone: Tx/Rx. No SPI: FD >> TxSYNC; HD20 or HD10: Tx/Rx. Rev. 0 | Page 8 of 52 IFACE2 SPI_CS IFACE3 TxPWRDWN U9 RxPWRDWN U8 ADC_AVDD U7 REFT U6 ADC_AVSS U5 VIN+A U4 VIN–A U3 VREF U2 VIN–B U1 VIN+B U0 ADC_AVSS AUX_DACA/AUX_ADCA2 REFB AUX_DACB/AUX_ADCA1 ADC_AVDD DRVDD PLL_AVDD DRVSS PLL_AVSS AD9861 1 2, 3 Pin No. Name Description 34 AUX_SPI_CLK CLK for AuxSPI. 35–44 L9–L0 Lower Data Bit 9 to Lower Data Bit 0. 45 AUX3 Configurable as either AuxADC_B or AuxDAC_C. 46 RESET Chip Reset When Low. 47 AUX_ADC_REF Decoupling for AuxADC On-Chip Reference. 48 CLKIN Clock Input. 52 REFB ADC Bottom Reference. 54, 55 VIN+B, VIN−B ADC B Differential Input. 56 VREF ADC Band Gap Reference. 57, 58 VIN−A, VIN+A ADC A Differential Input. 60 REFT ADC Top Reference. 62 RxPwrDwn Rx Analog Power-Down Control. 63 TxPwrDwn Tx Analog Power-Down Control. 64 SPI_CS SPI: Serial Port Chip Select. At power-up or reset, this must be high. No SPI: Tie low to disable SPI and use mode pins. This pin must be tied low. 1 Underlined pin names and descriptions apply when the device is configured without a serial port interface, referred to as no SPI mode. 2 Pin function depends if the serial port is used to configure the AD9861 (called SPI mode) or if mode pins are used to configure the AD9861 (called No SPI mode). The differences are indicated by the SPI and No SPI labels in the description column. 3 Some pin descriptions depend on the interface configuration, full-duplex (FD), half-duplex interleaved data (HD10), half-duplex parallel data (HD20), and a half-duplex interface similar to the AD9860 and AD9862 data interface called clone mode (Clone). Clone mode requires a serial port interface. Rev. 0 | Page 9 of 52 AD9861 TYPICAL PERFORMANCE CHARACTERISTICS 0 0 –10 –10 –20 –20 –30 –30 –40 –40 –50 –50 –60 –60 –70 –70 –80 –80 –90 –90 –100 –100 –110 –110 05 10 15 20 25 05 10 15 20 25 FREQUENCY (MHz) FREQUENCY (MHz) Figure 4. AD9861-50 Rx Path Single-Tone FFT of Rx Channel B Path Figure 7. AD9861-50 Rx Path Dual-Tone FFT of Rx Channel A Path Digitizing 2 MHz Tone Digitizing 1 MHz and 2 MHz Tones 0 0 –10 –10 –20 –20 –30 –30 –40 –40 –50 –50 –60 –60 –70 –70 –80 –80 –90 –90 –100 –100 –110 –110 05 10 15 20 25 05 10 15 20 25 FREQUENCY (MHz) FREQUENCY (MHz) Figure 5. AD9861-50 Rx Path Single-Tone FFT of Rx Channel B Path Figure 8. AD9861-50 Rx Path Dual-Tone FFT of Rx Channel A Path Digitizing 5 MHz Tone Digitizing 5 MHz and 8 MHz Tones 0 0 –10 –10 –20 –20 –30 –30 –40 –40 –50 –50 –60 –60 –70 –70 –80 –80 –90 –90 –100 –100 –110 –110 05 10 15 20 25 05 10 15 20 25 FREQUENCY (MHz) FREQUENCY (MHz) Figure 6. AD9861-50 Rx Path Single-Tone FFT of Rx Channel B Path Figure 9. AD9861-50 Rx Path Dual-Tone FFT of Rx Channel A Path Digitizing 24 MHz Tone Digitizing 20 MHz and 25 MHz Tones Rev. 0 | Page 10 of 52 AMPLITUDE (dBFS) AMPLITUDE (dBFS) AMPLITUDE (dBFS) 03606-0-033 03606-0-031 03606-0-035 AMPLITUDE (dBFS) AMPLITUDE (dBFS) AMPLITUDE (dBFS) 03606-0-036 03606-0-032 03606-0-034 AD9861 0 0 –10 –10 –20 –20 –30 –30 –40 –40 –50 –50 –60 –60 –70 –70 –80 –80 –90 –90 –100 –100 –110 –110 05 10 15 20 25 05 10 15 20 25 FREQUENCY (MHz) FREQUENCY (MHz) Figure 10. AD9861-50 Rx Path Single-Tone FFT of Rx Channel B Path Figure 13. AD9861-50 Rx Path Dual-Tone FFT of Rx Channel A Path Digitizing 76 MHz Tone Digitizing 70 MHz and 72 MHz Tones 62 62 10.0 NORMAL POWER @ 50MSPS NORMAL POWER @ 50MSPS 9.8 9.6 LOW POWER ADC @ 25MSPS LOW POWER ADC @ 25MSPS 59 59 9.4 9.2 56 56 9.0 8.8 ULTRALOW POWER ADC ULTRALOW POWER ADC 8.6 @ 16MSPS @ 16MSPS 53 53 8.4 8.2 50 50 8.0 05 10 15 20 25 05 10 15 20 25 INPUT FREQUENCY (MHz) INPUT FREQUENCY (MHz) Figure 11. AD9861-50 Rx Path at 50 MSPS, 10 MHz Input Tone Figure 14. AD9861-50 Rx Path at 50 MSPS, 10 MHz Input Tone SNR Performance vs. Input Frequency SINAD Performance vs. Input Frequency 80 –50 LOW POWER ADC @ 25MSPS –55 75 NORMAL POWER @ 50MSPS –60 70 ULTRALOW POWER ADC @ 16MSPS 65 –65 NORMAL POWER @ 50MSPS 60 –70 ULTRALOW POWER ADC @ 16MSPS –75 55 LOW POWER ADC @ 25MSPS –80 50 05 10 15 20 25 05 10 15 20 25 INPUT FREQUENCY (MHz) INPUT FREQUENCY (MHz) Figure 12. AD9861-50 Rx Path at 50 MSPS, 10 MHz Input Tone Figure 15. AD9861-50 Rx Path at 50 MSPS, 10 MHz Input Tone SFDR Performance vs. Input Frequency THD Performance vs. Input Frequency Rev. 0 | Page 11 of 52 SFDR (dBc) SNR (dBc) AMPLITUDE (dBFS) 03606-0-041 03606-0-039 03606-0-037 SINAD (dBc) THD (dBc) AMPLITUDE (dBFS) 03606-0-042 03606-0-038 03606-0-040 ENOB (Bits) AD9861 70 90 –90 SFDR 60 80 –80 70 50 –70 THD 40 60 –60 IDEAL SNR 30 50 –50 SNR 20 40 –40 10 30 –30 0 20 –20 0 –5 –10 –15 –20 –25 –30 –35 –40 –45 0 –5 –10 –15 –20 –25 –30 –35 –40 INPUT AMPLITUDE (dBFS) INPUT AMPLITUDE (dBFS) Figure 16. AD9861-50 Rx Path at 50 MSPS, 10 MHz Input Tone Figure 19. AD9861-50 Rx Path at 50 MSPS, 10 MHz Input Tone SNR Performance vs. Input Amplitude THD and SFDR Performance vs. Input Amplitude 62 10.0 62 9.9 AVE (–40°C) 61 61 AVE (–40°C) 9.8 AVE (+25°C) AVE (+25°C) 9.7 60 60 9.6 AVE (+85°C) 59 9.5 AVE (+85°C) 59 9.4 58 9.3 58 9.2 57 57 9.1 56 9.0 56 2.7 3.0 3.3 3.6 2.7 3.0 3.3 3.6 ADC_AVDD VOLTAGE (V) ADC_AVDD VOLTAGE (V) Figure 20. AD9861-50 Rx Path at 50 MSPS, 10 MHz Input Tone Figure 17. AD9861-50 Rx Path at 50 MSPS, 10 MHz Input Tone SINAD Performance vs. ADC_AVDD and Temperature SNR Performance vs. ADC_AVDD and Temperature 70 –70.0 –70.5 71 –71.0 72 AVE (+85°C) –71.5 AVE (+85°C) 73 –72.0 AVE (+25°C) 74 –72.5 AVE (+25°C) –73.0 75 AVE (–40°C) –73.5 76 AVE (–40°C) –74.0 77 –74.5 78 –75.0 3.6 3.3 3.0 2.7 3.6 3.3 3.0 2.7 INPUT AMPLITUDE (dBFS) INPUT AMPLITUDE (dBFS) Figure 21. AD9861-50 Rx Path Single-Tone SFDR Performance vs. Figure 18. AD9861-50 Rx Path Single-Tone THD Performance vs. ADC_AVDD and Temperature ADC_AVDD and Temperature Rev. 0 | Page 12 of 52 THD (dBc) SNR (dBc) SNR (dBc) 03606-0-045 03606-0-043 03606-0-047 SINAD (dBc) SFDR (dBFS) SFDR (dBc) 03606-0-048 ENOB (Bits) THD (dBFS) 03606-0-046 03606-0-044 AD9861 0 0 –10 –10 –20 –20 –30 –30 –40 –40 –50 –50 –60 –60 –70 –70 –80 –80 –90 –90 –100 –100 –110 –110 0 5 10 15 20 25 30 35 40 0 5 10 15 20 25 FREQUENCY (MHz) FREQUENCY (MHz) Figure 22. AD9861-80 Rx Path Single-Tone FFT of Rx Channel B Path Figure 25. AD9861-80 Rx Path Dual-Tone FFT of Rx Channel A Path Digitizing 2 MHz Tone Digitizing 1 MHz and 2 MHz Tones 0 0 –10 –10 –20 –20 –30 –30 –40 –40 –50 –50 –60 –60 –70 –70 –80 –80 –90 –90 –100 –100 –110 –110 0 5 10 15 20 25 30 35 40 0 5 10 15 20 25 FREQUENCY (MHz) FREQUENCY (MHz) Figure 23. AD9861-80 Rx Path Single-Tone FFT of Rx Channel B Path Figure 26. AD9861-80 Rx Path Dual-Tone FFT of Rx Channel A Path Digitizing 5 MHz Tone Digitizing 5 MHz and 8 MHz Tones 0 0 –10 –10 –20 –20 –30 –30 –40 –40 –50 –50 –60 –60 –70 –70 –80 –80 –90 –90 –100 –100 –110 –110 0 5 10 15 20 25 30 35 40 0 5 10 15 20 25 FREQUENCY (MHz) FREQUENCY (MHz) Figure 24. AD9861-80 Rx Path Single-Tone FFT of Rx Channel B Path Figure 27. AD9861-80 Rx Path Dual-Tone FFT of Rx Channel A Path Digitizing 24 MHz Tone Digitizing 20 MHz and 25 MHz Tones Rev. 0 | Page 13 of 52 AMPLITUDE (dBFS) AMPLITUDE (dBFS) AMPLITUDE (dBFS) 03606-0-053 03606-0-051 03606-0-049 AMPLITUDE (dBFS) AMPLITUDE (dBFS) AMPLITUDE (dBFS) 03606-0-054 03606-0-052 03606-0-050 AD9861 62 62 10.0 LOW POWER ADC @ 40MSPS LOW POWER ADC @ 40MSPS ULTRALOW POWER ADC @ 16MSPS 9.8 ULTRALOW POWER ADC @ 16MSPS 9.6 59 59 9.4 NORMAL POWER @ 80MSPS NORMAL POWER @ 80MSPS 9.2 56 56 9.0 8.8 8.6 53 53 8.4 8.2 50 50 8.0 0 5 10 15 20 25 30 0 5 10 15 20 25 30 INPUT FREQUENCY (MHz) INPUT FREQUENCY (MHz) Figure 28. AD9861-80 Rx Path at 80 MSPS, 10 MHz Input Tone Figure 31. AD9861-80 Rx Path at 80 MSPS, 10 MHz Input Tone SNR Performance vs. Input Frequency and Power Setting SINAD Performance vs. Input Frequency and Power Setting 85 –50 LOW POWER ADC @ 40MSPS –55 80 ULTRALOW POWER –60 ADC @ 16MSPS 75 –65 LOW POWER ADC @ 40MSPS 70 –70 NORMAL POWER @ 80MSPS 65 –75 ULTRALOW POWER ADC @ 16MSPS NORMAL POWER @ 80MSPS 60 –80 0 5 10 15 20 25 0 5 10 15 20 25 INPUT FREQUENCY (MHz) INPUT FREQUENCY (MHz) Figure 29. AD9861-80 Rx Path at 80 MSPS, 10 MHz Input Tone Figure 32. AD9861-80 Rx Path at 80 MSPS, 10 MHz Input Tone SFDR Performance vs. Input Frequency and Power Setting THD Performance vs. Input Frequency and Power Setting 70 –80 80 60 –70 70 50 –60 SFDR 60 40 IDEAL SNR –50 50 30 THD –40 40 20 SNR –30 30 10 0 –20 20 0 –5 –10 –15 –20 –25 –30 –35 –40 –45 0 –5 –10 –15 –20 –25 –30 –35 –40 INPUT AMPLITUDE (dBFS) INPUT AMPLITUDE (dBFS) Figure 30. AD9861-80 Rx Path at 80 MSPS, 10 MHz Input Tone Figure 33. AD9861-80 Rx Path at 80 MSPS, 10 MHz Input Tone SNR Performance vs. Input Amplitude THD Performance vs. Input Amplitude Rev. 0 | Page 14 of 52 SNR (dBc) SFDR (dBc) SNR (dBc) 03606-0-057 03606-0-055 03606-0-059 THD (dBFS) SINAD (dBc) THD (dBc) 03606-0-058 ENOB (Bits) SFDR (dBFS) 03606-0-056 03606-0-060 AD9861 62 62 10.0 9.9 61 61 9.8 AVE (–40°C) AVE (+85°C) 9.7 60 60 AVE (+85°C) 9.6 AVE (+25°C) 59 59 9.5 AVE (+25°C) 9.4 58 58 9.3 AVE (–40°C) 9.2 57 57 9.1 56 56 9.0 2.7 3.0 3.3 3.6 2.7 3.0 3.3 3.6 ADC_AVDD VOLTAGE (V) ADC_AVDD VOLTAGE (V) Figure 34. AD9861-80 Rx Path at 80 MSPS, 10 MHz Input Tone Figure 37. AD9861-80 Rx Path at 80 MSPS, 10 MHz Input Tone SNR Performance vs. AVDD and Temperature SINAD Performance vs. AVDD and Temperature 70 65 AVE (+85°C) 69 66 AVE (–40°C) 68 67 AVE (+25°C) AVE (–40°C) 67 68 AVE (+25°C) 66 69 65 70 AVE (+85°C) 64 71 63 72 62 73 61 74 60 75 2.7 3.0 3.3 3.6 2.7 3.0 3.3 3.6 ADC_AVDD VOLTAGE (V) ADC_AVDD VOLTAGE (V) Figure 35. AD9861-80 Rx Path at 80 MSPS, 10 MHz Input Tone Figure 38. AD9861-80 Rx Path at 80 MSPS, 10 MHz Input Tone THD Performance vs. AVDD and Temperature SFDR Performance vs. AVDD and Temperature 120 180 NORM 160 NORM 100 140 80 120 100 LP 60 LP 80 40 60 ULP 40 20 ULP 20 0 0 04 10 20 300 50 0 10 20 30 4050 6070 80 F (MHz) F (MHz) CLK CLK Figure 36. AD9861-50 ADC_AVDD Current vs. Sampling Rate for Figure 39. AD9861-80 ADC_AVDD Current vs. ADC Sampling Rate for Different ADC Power Levels Different ADC Power Levels Rev. 0 | Page 15 of 52 ADC AVDD CURRENT (mA) THD (dBc) SNR (dBc) 03606-0-063 03606-0-061 03606-0-065 SINAD (dBc) ADC AVDD CURRENT (mA) SFDR (dBc) 03606-0-064 03606-0-062 ENOB (Bits) 03606-0-066 AD9861 0 0 –10 –10 –20 –20 –30 –30 –40 –40 –50 –50 –60 –60 –70 –70 –80 –80 –90 –90 –100 –100 –110 –110 0 5 101520 25 01 501520 25 FREQUENCY (MHz) FREQUENCY (MHz) Figure 40. AD9861 Tx Path 1 MHz Single-Tone Output FFT of Tx Path Figure 43. AD9861 Tx Path 5 MHz Single-Tone Output FFT of Tx Path with 20 mA Full-Scale Output into 33 Ω Differential Load with 20 mA Full-Scale Output into 33 Ω Differential Load 0 0 –10 –10 –20 –20 –30 –30 –40 –40 –50 –50 –60 –60 –70 –70 –80 –80 –90 –90 –100 –100 –110 –110 01 501520 25 01 501520 25 FREQUENCY (MHz) FREQUENCY (MHz) Figure 41. AD9861 Tx Path 1 MHz Single-Tone Output FFT of Tx Path Figure 44. AD9861 Tx Path 5 MHz Single-Tone Output FFT of Tx Path with 20 mA Full-Scale Output into 60 Ω Differential Load with 20 mA Full-Scale Output into 60 Ω Differential Load 0 0 –10 –10 –20 –20 –30 –30 –40 –40 –50 –50 –60 –60 –70 –70 –80 –80 –90 –90 –100 –100 –110 –110 01 501520 25 01 501520 25 FREQUENCY (MHz) FREQUENCY (MHz) Figure 42. AD9861 Tx Path 1 MHz Single-Tone Output FFT of Tx Path Figure 45. AD9861 Tx Path 5 MHz Single-Tone Output FFT of Tx Path with 2 mA Full-Scale Output into 600 Ω Differential Load with 2 mA Full-Scale Output into 600 Ω Differential Load Rev. 0 | Page 16 of 52 AMPLITUDE (dBc) AMPLITUDE (dBc) AMPLITUDE (dBc) 03606-0-072 03606-0-070 03606-0-068 AMPLITUDE (dBc) AMPLITUDE (dBc) AMPLITUDE (dBc) 03606-0-073 03606-0-071 03606-0-069 AD9861 –50 –50 –60 –60 –70 –70 –80 –80 –90 –90 –100 –100 01 501520 25 01 501520 25 OUTPUT FREQUENCY (MHz) OUTPUT FREQUENCY (MHz) Figure 46. AD9861 Tx Path THD vs. Output Frequency of Tx Path with Figure 49. AD9861 Tx Path THD vs. Output Frequency of Tx Path 20 mA Full-Scale Output into 60 Ω Differential Load with 2 mA Full-Scale Output into 600 Ω Differential Load 62 62 61 61 60 60 59 59 58 58 57 57 56 56 01 501520 25 01 501520 25 OUTPUT FREQUENCY (MHz) OUTPUT FREQUENCY (MHz) Figure 47. AD9861 Tx Path SINAD vs. Output Frequency of Tx Path, with Figure 50. AD9861 Tx Path SINAD vs. Output Frequency of Tx Path, with 20 mA Full-Scale Output into 60 Ω Differential Load 2 mA Full-Scale Output into 600 Ω Differential Load –70 –70 –75 –75 –80 –80 –85 –85 –90 –90 –95 –95 01 501520 25 01 501520 25 OUTPUT FREQUENCY (MHz) OUTPUT FREQUENCY (MHz) Figure 48. AD9861 Tx Path Dual-Tone (0.5 MHz Spacing) IMD vs. Figure 51. AD9861 Tx Path Dual-Tone (0.5 MHz Spacing) IMD vs. Output Frequency of Tx Path, with Output Frequency of Tx Path, with 20 mA Full-Scale Output into 60 Ω Differential Load 2 mA Full-Scale Output into 600 Ω Differential Load Rev. 0 | Page 17 of 52 IMD (dBc) SINAD (dBc) THD (dBc) 03606-0-078 03606-0-076 03606-0-074 IMD (dBc) SINAD (dBc) THD (dBc) 03606-0-079 03606-0-077 03606-0-075 AD9861 Figure 52 to Figure 57 use the same input data to the Tx path, a 64-carrier OFDM signal over a 20 MHz bandwidth, centered at 20 MHz. The center two carriers are removed from the signal to observe the in-band intermodulation distortion (IMD) from the DAC output. –30 –30 –40 –40 –50 –50 –60 –60 –70 –70 –80 –80 –90 –90 –100 –100 –110 –110 –120 –120 –130 –130 7.5 12.5 17.5 22.5 27.5 32.5 18.75 19.25 19.75 20.25 20.75 21.25 FREQUENCY (MHz) FREQUENCY (MHz) Figure 52. AD9861 Tx Path FFT, 64-Carrier (Center Two Carriers Removed) Figure 55. AD9861 Tx Path FFT, In-Band IMD Products of OFDM Signal over 20 MHz Bandwidth, Centered at 20 MHz, with OFDM Signal in Figure 52 20 mA Full-Scale Output into 60 Ω Differential Load –30 –30 –40 –40 –50 –50 –60 –60 –70 –70 –80 –80 –90 –90 –100 –100 –110 –110 –120 –120 –130 –130 7.5 8.0 8.5 9.0 9.5 10.0 10.5 11.0 11.5 12.0 12.5 27.5 28.0 28.5 29.0 29.5 30.0 30.5 31.0 31.5 32.0 32.5 FREQUENCY (MHz) FREQUENCY (MHz) Figure 53. AD9861 Tx Path FFT, Lower-Band IMD Products of Figure 56. AD9861 Tx Path FFT, Upper-Band IMD Products of OFDM Signal in Figure 52 OFDM Signal in Figure 52 –30 –30 –40 –40 –50 –50 –60 –60 –70 –70 –80 –80 –90 –90 –100 –100 –110 –110 –120 –120 –130 –130 0 1020304050 6070 80 0 1020304050 6070 80 FREQUENCY (MHz) FREQUENCY (MHz) Figure 54. AD9861 Tx Path FFT of OFDM Signal in Figure 52, Figure 57. AD9861 Tx Path FFT of OFDM Signal in Figure 52, with 1× Interpolation with 4× Interpolation Rev. 0 | Page 18 of 52 AMPLITUDE (dBc) AMPLITUDE (dBc) AMPLITUDE (dBc) 03606-0-084 03606-0-082 03606-0-080 AMPLITUDE (dBc) AMPLITUDE (dBc) AMPLITUDE (dBc) 03606-0-085 03606-0-083 03606-0-081 AD9861 Figure 58 to Figure 63 use the same input data to the Tx path, a 256-carrier OFDM signal over a 1.75 MHz bandwidth, centered at 7 MHz. The center four carriers are removed from the signal to observe the in-band intermodulation distortion (IMD) from the DAC output. –40 –40 –50 –50 –60 –60 –70 –70 –80 –80 –90 –90 –100 –100 –110 –110 –120 –120 –130 –130 –140 –140 6.0 6.2 6.4 6.6 6.8 7.0 7.2 7.4 7.6 7.8 8.0 6.97 6.98 6.99 7.00 7.01 7.02 7.03 FREQUENCY (MHz) FREQUENCY (MHz) Figure 58. AD9861 Tx Path FFT, 256-Carrier (Center Four Carriers Removed) Figure 61. AD9861 Tx Path FFT, In-Band IMD Products of OFDM Signal over 1.75 MHz Bandwidth, Centered at 7 MHz, with OFDM Signal in Figure 58 20 mA Full-Scale Output into 60 Ω Differential Load –40 –40 –50 –50 –60 –60 –70 –70 –80 –80 –90 –90 –100 –100 –110 –110 –120 –120 –130 –130 –140 –140 6.06 6.08 6.10 6.12 6.14 6.16 6.18 7.81 7.83 7.85 7.87 7.89 7.91 7.93 FREQUENCY (MHz) FREQUENCY (MHz) Figure 59. AD9861 Tx Path FFT, Lower-Band IMD Products of Figure 62. AD9861 Tx Path FFT, Upper-Band IMD Products of OFDM Signal in Figure 58 OFDM Signal in Figure 52 –30 –30 –40 –40 –50 –50 –60 –60 –70 –70 –80 –80 –90 –90 –100 –100 –110 –110 –120 –120 –130 –130 0 5 10 15 20 25 0 5 10 15 20 25 FREQUENCY (MHz) FREQUENCY (MHz) Figure 60. AD9861 Tx Path FFT of OFDM Signal in Figure 52, Figure 63. AD9861 Tx Path FFT of OFDM Signal in Figure 52, with 1× Interpolation with 4× Interpolation Rev. 0 | Page 19 of 52 AMPLITUDE (dBc) AMPLITUDE (dBc) AMPLITUDE (dBc) 03606-0-090 03606-0-088 03606-0-086 AMPLITUDE (dBc) AMPLITUDE (dBc) AMPLITUDE (dBc) 03606-0-091 03606-0-089 03606-0-087 AD9861 Figure 64 to Figure 69 use the same input data to the Tx path, a 256-carrier OFDM signal over a 23 MHz bandwidth, centered at 23 MHz. The center four carriers are removed from the signal to observe the in-band intermodulation distortion (IMD) from the DAC output. –40 –40 –50 –50 –60 –60 –70 –70 –80 –80 –90 –90 –100 –100 –110 –110 –120 –120 –130 –130 –140 –140 9 1419 2429 34 22.6 22.7 22.8 22.9 23.0 23.1 23.2 23.3 23.4 FREQUENCY (MHz) FREQUENCY (MHz) Figure 64. AD9861 Tx Path FFT, 256-Carrier (Center Four Carriers Removed) Figure 67. AD9861 Tx Path FFT, In-Band IMD Products of OFDM Signal over 23 MHz Bandwidth, Centered at 7 MHz, with OFDM Signal in Figure 64 20 mA Full-Scale Output into 60 Ω Differential Load –40 –40 –50 –50 –60 –60 –70 –70 –80 –80 –90 –90 –100 –100 –110 –110 –120 –120 –130 –130 –140 –140 10.5 10.7 10.9 11.1 11.3 11.5 11.7 11.9 12.1 12.3 12.5 33.5 33.7 33.9 34.1 34.3 34.5 34.7 34.9 35.1 35.3 35.5 FREQUENCY (MHz) FREQUENCY (MHz) Figure 65. AD9861 Tx Path FFT, Lower-Band IMD Products of Figure 68. AD9861 Tx Path FFT, Upper-Band IMD Products of OFDM Signal in Figure 64 OFDM Signal in Figure 64 –30 –30 –40 –40 –50 –50 –60 –60 –70 –70 –80 –80 –90 –90 –100 –100 –110 –110 –120 –120 –130 –130 0 10 203040 506070 8090 0 10 203040 506070 8090 FREQUENCY (MHz) FREQUENCY (MHz) Figure 66. AD9861 Tx Path FFT of OFDM Signal in Figure 52 Figure 69. AD9861 Tx Path FFT of OFDM Signal in Figure 52 with 1× Interpolation with 4× Interpolation Rev. 0 | Page 20 of 52 AMPLITUDE (dBc) AMPLITUDE (dBc) AMPLITUDE (dBc) 03606-0-096 03606-0-094 03606-0-092 AMPLITUDE (dBc) AMPLITUDE (dBc) AMPLITUDE (dBc) 03606-0-097 03606-0-095 03606-0-093 AD9861 TERMINOLOGY Input Bandwidth Harmonic Distortion, Second The analog input frequency at which the spectral power of the The ratio of the rms signal amplitude to the rms value of the fundamental frequency (as determined by the FFT analysis) is second harmonic component, reported in dBc. reduced by 3 dB. Harmonic Distortion, Third Aperture Delay The ratio of the rms signal amplitude to the rms value of the The delay between the 50% point of the rising edge of the third harmonic component, reported in dBc. CLKIN signal and the instant at which the analog input is Integral Nonlinearity actually sampled. The deviation of the transfer function from a reference line Aperture Uncertainty (Jitter) measured in fractions of an LSB using a “best straight line” The sample-to-sample variation in aperture delay. determined by a least square curve fit. Crosstalk Minimum Conversion Rate Coupling onto one channel being driven by a –0.5 dBFS signal The encode rate at which the SNR of the lowest analog signal when the adjacent interfering channel is driven by a full-scale frequency drops by no more than 3 dB below the guaranteed signal. limit. Differential Analog Input Voltage Range Maximum Conversion Rate The peak-to-peak differential voltage that must be applied to The encode rate at which parametric testing is performed. the converter to generate a full-scale response. Peak differential voltage is computed by observing the voltage on a single pin Output Propagation Delay and subtracting the voltage from the other pin, which is 180° The delay between a differential crossing of CLK+ and CLK− out of phase. Peak-to-peak differential is computed by rotating and the time when all output data bits are within valid logic the input phase 180° and taking the peak measurement again. levels. Then the difference is computed between both peak Power Supply Rejection Ratio measurements. The ratio of a change in input offset voltage to a change in Differential Nonlinearity power supply voltage. The deviation of any code width from an ideal 1 LSB step. Signal-to-Noise and Distortion (SINAD) Effective Number of Bits (ENOB) The ratio of the rms signal amplitude (set 1 dB below full-scale) The effective number of bits is calculated from the measured to the rms value of the sum of all other spectral components, SNR based on the following equation: including harmonics, but excluding dc. Signal-to-Noise Ratio (without Harmonics) SNR −1.76dB MEASURED ENOB= The ratio of the rms signal amplitude (set at 1 dB below full 6.02 scale) to the rms value of the sum of all other spectral Pulse Width/Duty Cycle components, excluding the first five harmonics and dc. Pulse width high is the minimum amount of time that a signal Spurious-Free Dynamic Range (SFDR) should be left in the logic high state to achieve rated perform- The ratio of the rms signal amplitude to the rms value of the ance; pulse width low is the minimum time a signal should be peak spurious spectral component. The peak spurious left in the low state, logic low. component may or may not be a harmonic. It also may be Full-Scale Input Power reported in dBc (i.e., degrades as signal level is lowered) or Expressed in dBm, full-scale input power is computed using the dBFS (i.e., always related back to converter full scale). SFDR following equation: does not include harmonic distortion components. 2 ⎛ ⎞ V Z FULLSCALE−RMS INPUT Worst Other Spur ⎜ ⎟ Power = 10log FULLSCALE ⎜ ⎟ 0.001 The ratio of the rms signal amplitude to the rms value of the ⎝ ⎠ worst spurious component (excluding the second and third Gain Error harmonics) reported in dBc. Gain error is the difference between the measured and ideal full-scale input voltage range of the ADC. Rev. 0 | Page 21 of 52 AD9861 THEORY OF OPERATION SYSTEM BLOCK The AD9861 is targeted to cover the mixed-signal front end The differential input stage is dc self-biased and allows needs of multiple wireless communication systems. It features a differential or single-ended inputs. The output-staging block receive path that consists of dual 10-bit receive ADCs, and a aligns the data, carries out the error correction, and passes the data to the output buffers. transmit path that consists of dual 10-bit transmit DACs (TxDAC). The AD9861 integrates additional functionality The latency of the Rx path is about 5 clock cycles. typically required in most systems, such as power scalability, additional auxiliary converters, Tx gain control, and clock Rx Path Analog Input Equivalent Circuit multiplication circuitry. The Rx path analog inputs of the AD9861 incorporate a novel structure that merges the function of the input sample-and- The AD9861 minimizes both size and power consumption to hold amplifiers (SHAs) and the first pipeline residue amplifiers address the needs of a range of applications from the low power into a single, compact switched capacitor circuit. This structure portable market to the high performance base station market. achieves considerable noise and power savings over a conven- The part is provided in a 64-lead lead frame chip scale package tional implementation that uses separate amplifiers by eliminating (LFCSP) that has a footprint of only 9 mm × 9 mm. Power one amplifier in the pipeline. consumption can be optimized to suit the particular application beyond just a speed grade option by incorporating power-down Figure 70 illustrates the equivalent analog inputs of the AD9861 controls, low power ADC modes, TxDAC power scaling, and a (a switched capacitor input). Bringing CLK to logic high opens half-duplex mode, which automatically disables the unused switch S3 and closes switches S1 and S2; this is the sample mode digital path. of the input circuit. The input source connected to VIN+ and VIN− must charge capacitor CH during this time. Bringing CLK The AD9861 uses two 10-bit buses to transfer Rx path data and to a logic low opens S2, and then switch S1 opens followed by Tx path data. These two buses support 20-bit parallel data closing S3. This puts the input circuit into hold mode. transfers or 10-bit interleaved data transfers. The bus is S1 C configurable through either external mode pins or through H VIN+ + internal registers settings. The registers allow many more C R IN IN options for configuring the entire device. S3 S2 V CM R C IN H The following sections discuss the various blocks of the AD9861: – VIN– C Rx block, Tx block, the auxiliary converters, the digital block, IN programmable registers and the clock distribution block. 03606-0-002 Figure 70. Differential Input Architecture Rx PATH BLOCK The structure of the input SHA places certain requirements on Rx Path General Description the input drive source. The differential input resistors are The AD9861 Rx path consists of two 10-bit, 50 MSPS (for the typically 2 kΩ each. The combination of the pin capacitance, AD9861-50) or 80 MSPS (for the AD9861-80) analog-to-digital C , and the hold capacitance, C , is typically less than 5 pF. The IN H converters (ADCs). The dual ADC paths share the same input source must be able to charge or discharge this capaci- clocking and reference circuitry to provide optimal matching tance to 10-bit accuracy in one-half of a clock cycle. When the characteristics. Each of the ADCs consists of a 9-stage differen- SHA goes into sample mode, the input source must charge or tial pipelined switched capacitor architecture with output error discharge capacitor CH from the voltage already stored on it to correction logic. the new voltage. In the worst case, a full-scale voltage step on the input source must provide the charging current through the The pipelined architecture permits the first stage to operate on a R of switch S1 (typically 100 Ω) to a settled voltage within ON new input sample, while the remaining stages operate on one-half of the ADC sample period. This situation corresponds preceding samples. Sampling occurs on the falling edge of the to driving a low input impedance. On the other hand, when the input clock. Each stage of the pipeline, excluding the last, source voltage equals the value previously stored on CH, the consists of a low resolution flash ADC and a residual multiplier hold capacitor requires no input current and the equivalent to drive the next stage of the pipeline. The residual multiplier input impedance is extremely high. uses the flash ADC output to control a switched capacitor digital-to-analog converter (DAC) of the same resolution. The DAC output is subtracted from the stage’s input signal, and the residual is amplified (multiplied) to drive the next pipeline stage. The residual multiplier stage is also called a multiplying DAC (MDAC). One bit of redundancy is used in each one of the stages to facilitate digital correction of flash errors. The last stage simply consists of a flash ADC. Rev. 0 | Page 22 of 52 AD9861 Rx Path Application Section default 1 V VREF reference accepts a 2 V p-p differential input swing and the offset voltage should be Adding series resistance between the output of the signal source and the VIN pins reduces the drive requirements placed on the REFT = AVDD/2 + 0.5 V signal source. Figure 71 shows this configuration. REFB = AVDD/2 – 0.5 V AD9861 R AD9861 SERIES REFT VIN+ 0.1µF C SHUNT TO ADCs 0.1µF VIN– 10µF REFB R SERIES 0.1µF 03606-0-003 VREF Figure 71. Typical Input The bandwidth of the particular application limits the size of 10µF 0.1µF 0.5V this resistor. For applications with signal bandwidths less than 10 MHz, the user may insert series input resistors and a shunt capacitor to produce a low-pass filter for the input signal. 03606-0-020 Additionally, adding a shunt capacitance between the VIN pins can lower the ac load impedance. The value of this capacitance Figure 72. Typical Rx Path Decoupling depends on the source resistance and the required signal An external reference may be used for systems that require a bandwidth. different input voltage range, high accuracy gain matching between multiple devices, or improvements in temperature drift The Rx input pins are self-biased to provide this midsupply, and noise characteristics. When an external reference is desired, common-mode bias voltage, so it is recommended to ac couple the internal Rx band gap reference must be powered down the signal to the inputs using dc blocking capacitors. In systems using the VREF2 register [Register 0x5, Bit 4] and the external that must use dc coupling, use an op amp to comply with the reference driving the voltage level on the VREF pin. The input requirements of the AD9861. The inputs accept a signal external voltage level should be one-half of the desired peak-to- with a 2 V p-p differential input swing centered about one-half peak differential voltage swing. The result is that the differential of the supply voltage (AVDD/2). If the dc bias is supplied exter- voltage references are driven to new voltages: nally, the internal input bias circuit should be powered down by writing to registers Rx_A dc bias [Register 0x3, Bit 6] and Rx_B REFT = AVDD/2 +VREF/2 V dc bias [Register 0x4, Bit 7]. REFB = AVDD/2 – V /2 V REF The ADCs in the AD9861 are designed to sample differential If an external reference is used, it is recommended not to exceed input signals. The differential input provides improved noise a differential offset voltage for the reference greater than 1 V. immunity and better THD and SFDR performance for the Rx Clock Input and Considerations path. In systems that use single-ended signals, these inputs can Typical high speed ADCs use both clock edges to generate a be digitized, but it is recommended that a single-ended-to- variety of internal timing signals and, as a result, may be differential conversion be performed. A single-ended-to- sensitive to clock duty cycle. Commonly, a 5% tolerance is differential conversion can be performed by using a transformer required on the clock duty cycle to maintain dynamic perform- coupling circuit (typically for signals above 10 MHz) or by ance characteristics. The AD9861 contains clock duty cycle using an operational amplifier, such as the AD8138 (typically for signals below 10 MHz). stabilizer circuitry (DCS). The DCS retimes the internal ADC clock (nonsampling edge) and provides the ADC with a ADC Voltage References nominal 50% duty cycle. Input clock rates of over 40 MHz can The AD9861 10-bit ADCs use internal references that are use the DCS so that a wide range of input clock duty cycles can be designed to provide for a 2 V p-p differential input range. The accommodated. Conversely, DCS should not be used for Rx internal band gap reference generates a stable 1 V reference level sampling below 40 MSPS. Maintaining a 50% duty cycle clock is and is decoupled through the VREF pin. REFT and REFB are particularly important in high speed applications when proper the differential references generated based on the voltage level sample-and-hold times for the converter are required to of VREF. Figure 72 shows the proper decoupling of the refer- maintain high performance. The DCS can be enabled by writing ence pins VREF, REFT, and REFB when using the internal highs to the Rx_A/Rx_B CLK duty register bits [Register reference. Decoupling capacitors should be placed as close to 0x06/0x07, Bit 4]. the reference pins as possible. The duty cycle stabilizer uses a delay-locked loop to create the External references REFT and REFB are centered at AVDD/2 nonsampling edge. As a result, any changes to the sampling with a differential voltage equal to the voltage at VREF (by frequency require approximately 2 µs to 3 µs to allow the DLL default 1 V when using the internal reference), allowing a peak- to adjust to the new rate and settle. High speed, high resolution to-peak differential voltage swing of 2× VREF. For example, the ADCs are sensitive to the quality of the clock input. The Rev. 0 | Page 23 of 52 AD9861 degradation in SNR at a given full-scale input frequency (f ), 3, 4, and 5. Under this condition, the internal references are INPUT due only to aperture jitter (t ), can be calculated with the powered down. When either or both of the channel paths are A following equation: enabled after a power-down, the wake-up time is directly related to the recharging of the REFT and REFB decoupling capacitors SNR degradation = 20 log [(½)πF t )] IN A and the duration of the power-down. Typically, it takes approxi- mately 5 ms to restore full operation with fully discharged 0.1 µF In the equation, the rms aperture jitter, t , represents the root- A and 10 µF decoupling capacitors on REFT and REFB. sum-square of all jitter sources, which includes the clock input, analog input signal, and ADC aperture jitter specification. Tx PATH BLOCK Undersampling applications are particularly sensitive to jitter. The AD9861 transmit (Tx) path includes dual interpolating The clock input is a digital signal that should be treated as an 10-bit current output DACs that can be operated independently analog signal with logic level threshold voltages, especially in or can be coupled to form a complex spectrum in an image cases where aperture jitter may affect the dynamic range of the reject transmit architecture. Each channel includes two FIR AD9861. Power supplies for clock drivers should be separated filters, making the AD9861 capable of 1×, 2×, or 4× interpola- from the ADC output driver supplies to avoid modulating the tion. High speed input and output data rates can be achieved clock signal with digital noise. Low jitter crystal-controlled within the limitations of Table 9. oscillators make the best clock sources. If the clock is generated Table 9. AD9861 Tx Path Maximum Data Rate from another type of source (by gating, dividing, or other meth- ods), it should be retimed by the original clock at the last step. Input Data DAC Rate per Sampling Power Dissipation and Standby Mode Interpolation 20-Bit Interface Channel Rate Rate Mode (MSPS) (MSPS) The power dissipation of the AD9861 Rx path is proportional to FD, HD10, Clone 80 80 its sampling rate. The Rx path portion of the digital (DRVDD) 1× HD20 160 160 power dissipation is determined primarily by the strength of the FD, HD10, Clone 80 160 digital drivers and the load on each output bit. The digital drive 2× current can be calculated by HD20 80 160 FD, HD10, Clone 50 200 4× I = V × C × f × N DRVDD DRVDD LOAD CLOCK HD20 50 200 where N is the number of bits changing and C is the average LOAD By using the dual DAC outputs to form a complex signal, an load on the digital pins that changed. external analog quadrature modulator, such as the Analog The analog circuitry is optimally biased so that each speed Devices AD8349, can enable an image rejection architecture. grade provides excellent performance while affording reduced (Note: the AD9861 evaluation board includes a quadrature power consumption. Each speed grade dissipates a baseline modulator in the Tx path that accommodates the AD8345, power at low sample rates, which increases with clock frequency. AD8346 and the AD8345 footprints.) To optimize the image The baseline power dissipation for either speed grade can be rejection capability, as well as LO feedthrough suppression in reduced by asserting the ADC_LO_PWR pin, which reduces this architecture, the AD9861 offers programmable (via the SPI internal ADC bias currents by half, in some case resulting in port) fine (trim) gain and offset adjustment for each DAC. degraded performance. Also included in the AD9861 are a phase-locked loop (PLL) To further reduce power consumption of the ADC, the clock multiplier and a 1.2 V band gap voltage reference. With ADC_LO_PWR pin can be combined with a serial programmable the PLL enabled, a clock applied to the CLKIN input is multi- register setting to configure an ultralow power mode. The plied internally and generates all necessary internal synchronization ultralow power mode reduces the power consumption by a clocks. Each 10-bit DAC provides two complementary current fourth of the normal power consumption. The ultralow power outputs whose full-scale currents can be determined from a mode can be used at slower sampling frequencies or if reduced single external resistor. performance is acceptable. To configure the ultralow power An external pin, TxPWRDWN, can be used to power down the mode, assert the ADC_LO_PWR pin and write the following Tx path, when not used, to optimize system power consumption. register settings: Using the TxPWRDWN pin disables clocks and some analog Register 0x08 (MSB) ‘0000 1100’ circuitry, saving both digital and analog power. The power-down Register 0x09 (MSB) ‘0111 0000’ mode leaves the biases enabled to facilitate a quick recovery Register 0x0A (MSB) ‘0111 0000’ time, typically <10 µs. Additionally, a sleep mode is available, which turns off the DAC output current, but leaves all other Either of the ADCs in the AD9861 Rx path can be placed in circuits active, for a modest power savings. An SPI compliant standby mode independently by writing to the appropriate SPI serial port is used to program the many features of the AD9861. register bits in Registers 3, 4, and 5. The minimum standby Note that in power-down mode, the SPI port is still active. power is achieved when both channels are placed in full power- down mode using the appropriate SPI register bits in Registers Rev. 0 | Page 24 of 52 AD9861 DAC Equivalent Circuits 1.2V REFERENCE DAC A AND DAC B REFERENCE BIASES The AD9861 Tx path consisting of dual 10-bit DACs is shown in Figure 73. The DACs integrate a high performance TxDAC I OUTFSMAX REFIO core, a programmable gain control through a programmable CURRENT gain amplifier (TxPGA), coarse gain control, and offset adjust- SOURCE ARRAY ment and fine gain control to compensate for system mismatches. FSADJ I REF Coarse gain applies a gross scaling to either DAC by 1×, (1/2)×, 0.1µFR ≥ 4kΩ SET or (1/11)×. The TxPGA provides gain control from 0 dB to 03606-0-005 –20 dB in steps of 0.1 dB and is controlled via the 8-bit TxPGA Figure 74. Reference Circuitry setting. A fine gain adjustment of ±4% for each channel is con- Referring to the transfer function of the following equation, trolled through a 6-bit fine gain register. By default, coarse gain I is the maximum current output of the DAC with the OUTFSMAX is 1×, the TxPGA is set to 0 dB, and the fine gain is set to 0%. default gain setting (0 dB), and is based on a reference current, I . I is set by the internal 1.2 V reference and the external The TxDAC core of the AD9861 provides dual, differential, REF REF R resistor. complementary current outputs generated from the 10-bit data. SET The 10-bit dual DACs support update rates up to 200 MSPS. IOUTFSMAX = 64 × (REFIO/RSET) The differential outputs (IOUT+ and IOUT–) of each dual DAC are complementary, meaning that they always add up to the full- Typically, RSET is 4 kΩ, which sets IOUTFSMAX to 20 mA, the scale current output of the DAC, IOUTFS. Optimum ac performance optimal dynamic setting for the TxDACs. Increasing RSET by a loads or a transformer. factor of 2 proportionally decreases IOUTFSMAX by a factor of 2. I of each DAC can be rescaled either simultaneously OUTFSMAX OFFSET DAC using the TxPGA gain register or independently using the DAC A/DAC B coarse gain registers. + IOUT+A + TxDAC PGA + The TxPGA function provides 20 dB of simultaneous gain IOUT–A + range for both DACs, and is controlled by writing to the SPI register TxPGA gain for a programmable full-scale output of REFERENCE 10% to 100% of IOUTFSMAX. The gain curve is linear in dB, with BIAS steps of about 0.1 dB. Internally, the gain is controlled by changing the main DAC bias currents with an internal TxPGA + IOUT+B DAC whose output is heavily filtered via an on-chip R-C filter TxDAC PGA + to provide continuous gain transitions. Note that the settling + IOUT–B + time and bandwidth of the TxPGA DAC can be improved by a factor of 2 by writing to the TxPGA fast register. OFFSET DAC 03606-0-004 Each DAC has independent coarse gain control. Coarse gain Figure 73. TxDAC Output Structure Block Diagram control can be used to accommodate different IOUTFS from the The fine gain control provides improved balance of QAM dual DACs. The coarse full-scale output control can be adjusted modulated signals, resulting in improved modulation accuracy by using the DAC A/DAC B coarse gain registers to 1/2 or 1/11 and image rejection. of the nominal full-scale current. The independent DAC A and DAC B offset control adds a small Fine gain controls and dc offset controls can be used to dc current to either IOUT+ or IOUT– (not both). The selection compensate for mismatches (for system level calibration), of which IOUT this offset current is directed toward is allowing improved matching characteristics of the two Tx programmable via register setting. Offset control can be used channels and aiding in suppressing LO feedthrough. This is for suppression of an LO leakage signal that typically results at especially useful in image rejection architectures. The 10-bit dc the output of the modulator. If the AD9861 is dc-coupled to an offset control of each DAC can be used independently to external modulator, this feature can be used to cancel the output provide an offset of up to ±12% of I to either differential OUTFSMAX offset on the AD9861 as well as the input offset on the modulator. pin, thus allowing calibration of any system offsets. The fine The reference circuitry is shown in Figure 74. gain control with 5-bit resolution allows the IOUTFSMAX of each DAC to be varied over a ±4% range, allowing compensation of any DAC or system gain mismatches. Fine gain control is set through the DAC A/DAC B fine gain registers, and the offset control of each DAC is accomplished using the DAC A/DAC B offset registers. Rev. 0 | Page 25 of 52 AD9861 Clock Input Configuration The sleep mode, when activated, turns off the DAC output The quality of the clock and data input signals is important in currents, but the rest of the chip remains functioning. When achieving optimum performance. The external clock driver coming out of sleep mode, the AD9861 immediately returns to circuitry provides the AD9861 with a low jitter clock input that full operation. meets the min/max logic levels while providing fast edges. A full power-down mode can be enabled through the SPI When a driver is used to buffer the clock input, it should be register, which turns off all Tx path related analog and digital placed very close to the AD9861 clock input, thereby negating circuitry in the AD9861. When returning from full power-down any transmission line effects such as reflections due to mode, enough clock cycles must be allowed to flush the digital mismatch. filters of random data acquired during the power-down cycle. Programmable PLL Interpolation Stage CLKIN can function either as an input data rate clock (PLL Interpolation filters are available for use in the AD9861 transmit enabled) or as a DAC data rate clock (PLL disabled). path, providing 1× (bypassed), 2×, or 4× interpolation. The PLL clock multiplier and distribution circuitry produce the The interpolation filters effectively increase the Tx data rate necessary internal timing to synchronize the rising edge trig- while suppressing the original images. The interpolation filters gered latches for the enabled interpolation filters and DACs. digitally shift the worst-case image further away from the This circuitry consists of a phase detector, charge pump, voltage desired signal, thus reducing the requirements on the analog controlled oscillator (VCO), and clock distribution block, all output reconstruction filter. under SPI port control. The charge pump, phase detector, and VCO are powered from PLL_AVDD, while the clock distribu- There are two 2× interpolation filters available in the Tx path. tion circuits are powered from the DVDD supply. An interpolation rate of 4× is achieved using both interpolation filters; an interpolation rate of 2× is achieved by enabling only To ensure optimum phase noise performance from the PLL the first 2× interpolation filter. clock multiplier circuits, PLL_AVDD should originate from a clean analog supply. The speed of the VCO within the PLL also The first interpolation filter provides 2× interpolation using a has an effect on phase noise. 39-tap filter. It suppresses out-of-band signals by 60 dB or more and has a flat pass-band response (less than 0.1 dB ripple) The PLL locks with VCO speeds as low as 32 MHz up to extending to 38% of the input Tx data rate (19% of the DAC 350 MHz, but optimal phase noise with respect to VCO speed is update rate, fDAC). The maximum input data rate is 80 MSPS per achieved by running it in the range of 64 MHz to 200 MHz. channel when using 2× interpolation. Power Dissipation The second interpolation filter provides an additional 2× interpola- The AD9861 Tx path power is derived from three voltage tion for an overall 4× interpolation. The second filter is a 15-tap supplies: AVDD, DVDD, and DRVDD. filter, which suppresses out-of-band signals by 60 dB or more. IDRVDD and IDVDD are very dependent on the input data The flat pass-band response (less than 0.1 dB attenuation) is rate, the interpolation rate, and the activation of the internal 38% of the Tx input data rate (9.5% of f ). The maximum DAC digital modulator. IAVDD has the same type of sensitivity to input data rate per channel is 50 MSPS per channel when using data, interpolation rate, and the modulator function, but to a 4× interpolation. much lesser degree (< 10%). Latch/Demultiplexer Sleep/Power-Down Modes Data for the dual-channel Tx path can be latched in parallel The AD9861 provides multiple methods for programming through two ports in half-duplex operations (HD20 mode) or power saving modes. The externally controlled TxPWRDWN through a single port by interleaving the data (FD, HD10, and or SPI programmed sleep mode and full power-down mode are Clone modes). See the Flexible I/O Interface Options section in the main options. the Digital Block description and the Clock Distribution Block TxPWRDWN is used to disable all clocks and much of the section for further descriptions of each mode. analog circuitry in the Tx path when asserted. In this mode, the biases remain active, therefore reducing the time required for re-enabling the Tx path. The time of recovery from power- down for this mode is typically less than 10 µs. Rev. 0 | Page 26 of 52 AD9861 Update C, B, and A]. Slave mode is enabled by writing a high to AUXILIARY CONVERTERS the slave mode register bit [Register 0x28, Bit 7, Slave Enable]. The AD9861 contains auxiliary analog-to-digital converters (AuxADCs) and auxiliary digital-to-analog converters Another synchronization mode allows any combination of (AuxDACs). These auxiliary converters can be used to measure AuxDACs to be updated along with an externally applied rising or force system-wide control signals. edge to the TxPwrDwn pin. By default, the auxiliary converters are disabled and powered Typical settling time for the AuxDAC output is less than 0.5 µs, down. Enabling and controlling the auxiliary converters is but is dependent on the load. achieved through the serial programmable registers. Auxiliary ADCs Two auxiliary 10-bit SAR analog-to-digital converters Pins 29, 30, and 46 are configurable either as AuxDAC outputs or as AuxADC inputs. The respective AuxADC inputs are (AuxADCs) are available for monitoring various external connected to the external pin when a conversion is initiated and signals throughout the system, such as a receive signal strength are disconnected when the conversion is complete. The indicator (RSSI) function or temperature indicator. The AuxDAC outputs are enabled by writing to the respective AuxADCs have many SPI programmable options. Register power-up registers in Register 0x29. settings can be used to configure various full-scale reference options, change the sampling rate, and average multiple sample • Pin 29 can be connected to AuxDAC_A and/or readings. By default, the AuxADC start conversion and output AuxADC_A Channel 2. value is accessed through the register map. Additionally an auxiliary serial port can be enabled and used to initiate a • Pin 30 can be connected to AuxDAC_B and/or conversion and read back the AuxADC data. The auxiliary AuxADC_A Channel 1. serial port interface is available so that the normal SPI can be used to program other options while the AuxADC is accessed. • Pin 46 can be connected to AuxDAC_C and/or AuxADC_B. By default, the AuxADCs are powered down and automatically Auxiliary DACs powered up when a conversion is initiated. The AD9861 integrates three 8-bit voltage output auxiliary The two AuxADCs (AuxADC_A and AuxADC_B) can digital-to-analog converters (AuxDACs), which can be used for monitor up to three system signals. AuxADC_A has multi- supplying various control voltages throughout the system such plexed inputs that control whether pin AUX_ADC_A1 or pin as a VCXO voltage control or external VGA gain control. The AUX_ADC_A2 is connected to the input of AuxADC_A. The AuxDACs have a programmable full-scale output voltage, VOUTFS, multiplexer is programmed through Register 0x22, Bit 1, and can be synchronized to update with a single register write SelectA. By default, the register is low, which connects the or a rising edge on the TxPwrDwn pin. AUX_ADC_A2 pin to the input. By default, the AuxDAC outputs are powered down and require The full-scale AuxADC reference can be generated from the a serial write to the power-up registers [Register 0x29, Bits 2–0] analog supply (supply dependent), an internal reference, or to enable them. from an external applied reference. Table 10 shows the register settings required to select the AuxADC full-scale reference. The full-scale output of each AuxDAC is independently programmable to the full scales of 2.5 V, 2.7 V, 3.0 V, or 3.3 V by By default, an internal reference provides a buffered full-scale using Serial Register 0x17. The AuxDAC outputs have an I-to-V reference for both of the AuxADCs, which is equal to the driver that produces a voltage output that settles to ±1 LSB supply voltage for the AuxADCs (PLL_AVDD). A supply within 0.5 µs. The output driver is capable of sinking or sourcing independent 2.5 V or 3.0 V internal full-scale reference can be up to 6 mA. Using the AuxDAC requires the SPI to be operational. enabled by writing to register AuxADC Ref Enable and AuxADC Ref FS in Register 0x17. This internal reference is The AuxDACs are based on a resistor divider network. The based on the main Rx path ADC VREF voltage, so it requires AuxDACs output level is proportional to the straight binary the main Rx path VREF to be enabled. input codes from the appropriate SPI registers, Registers 0x24 to 0x26. By default, the AuxDAC output is updated immediately Another AuxADC full-scale reference option is an externally following the register write, but the update can occur supplied full-scale reference. The external reference can be synchronously to a single register write or to the TxPwrDwn applied to either or both of the AuxADCs by setting the rising edge. appropriate bit(s) in Registers 0x22 and 0x17. Setting either or both of these bits high disconnects the internal reference buffer In slave mode, the AuxDAC update occurs when a logic high is and enables the externally applied reference from the written to the appropriate update registers [Register 0x28, Bits 2–0, AuxADC_Ref pin to the respective channel(s). Rev. 0 | Page 27 of 52 AD9861 Table 10. Configuring AuxADC Reference Refsel A/B AuxADC_A Reference AuxADC Ref Enable AuxADC Ref FS [Register 0x22, Configuration [Register 0x17, Bit 1] [Register 0x17, Bit 0] Bit 2/Bit 5] Notes Buffered PLL_VDD 0 0 0 Default mode. Internal 3.0 V (3 x VREF) 1 0 1 Decouple at AUXADC_REF pin. VREF voltage from Rx path. Internal 2.5 V (2.5 x VREF) 1 1 1 Decouple at AUXADC_REF pin. Externally forced 0 Don't Care 1 Force and decouple at AUXADC_REF pin. AuxADCs and is available so that the SPI is not continually The AuxADCs can convert at rates of up to 5.33 MSPS busy retrieving AuxADC data. (0.1875 µs maximum conversion time) and have a bandwidth of around 200 kHz. The conversion time, including setup, The AuxSPI can be enabled and configured by setting register requires 12 clock cycles. The maximum clock rate for the AuxSPI enable [Register 0x22, Bit 7]. Also required is that the AuxADCs is 64 MHz and is generated from a divided down Rx normal serial port interface be configured for 3-wire mode (the ADC clock. The divide down ratio is controlled by register SPI_SDO pin must be disabled to use the Aux_SPI_SDO pin) AuxADC Clock Div [Register 0x23, Bits 1, 0]. By default, the Rx by setting the SDIO BiDir register bit [Register 0x00, Bit 7]. ADC clock is divided by 4. At an Rx ADC rate greater than 64 Register bit Sel BnotA [Register 0x22, Bit 6] configures whether MHz, the AuxADC Clock Div register must be set to divide-by- AuxADC_A or AuxADC_B is controlled by the AuxSPI. 2 or divide-by-4. AuxADC_A has two inputs: AuxADC_A1 and AuxADC_A2. Setting the Select A bit [Register 0x22, Bit 1] determines which On-chip averaging of 2, 4, 8, 16, 32, or 64 samples can be of the multiplexed inputs is connected to AuxADC_A. enabled through Register 0x18 for AuxADC_A or through Register 0x19 for AuxADC_B. When the averaging option is The AuxSPI consists of a chip select pin (AUX_SPI_CS, pin enabled, the AuxADC continually converts the number of number 4), a clock pin (AUX_SPI_CLK), and a data output pin samples specified and outputs the average value. (AUX_SPI_SDO multiplex with the SPI_SDO pin). A conversion is initiated by pulsing the AUX_SPI_CS pin low (AUX_SPI_CS There are three modes of operating the AuxADC: SPI operation should remain low during the entire conversion cycle, including mode (default), SPI with external start convert operation mode, the readback phase). When the conversion is complete, the data and Aux_SPI operation mode. pin, AUX_SPI_SDO, transitions from a logic low to a logic In the default SPI operation mode, a conversion is initiated by high. At this point, the user supplies an external clock on the writing a logic high to one or both of the start register bits, AUX_SPI_CLK pin. The AUX_SPI_CLK pin should be tied Start A or Start B [Register 0x22, Bit 0 or Bit 3]. If AuxADC is low when not in use. No data is present on the first rising edge. configured as averaging mode, the proper start bit is the Start The data output bit is updated on the falling edge of the clock Average AuxADC A/B register [Register 0x18, Bit 7/Register pulse and is settled by and can be latched on the next clock 0x19, Bit 7]. rising edge. The data arrives serially, MSB first. The AuxSPI runs at a rate up to 16 MHz. When the conversion is complete, the straight binary, 10-bit output data of the AuxADC is written to one of three reserved Operation of the Aux_SPI requires that 3-wire SPI mode be locations in the register map, depending on which AuxADC used, disabling the SDO pin. If the controller is a 4-wire and which multiplexed input is selected. Because the AuxADCs interface, a method of connecting the 3-wire AD9861 interface output 10 bits, two register addresses are needed for each data to the 4-wire controller is suggested in Figure 75. location. An example of an AuxSPI access is shown in Figure 75. In the In the optional SPI with external start convert operation mode, AuxSPI configuration, a start convert is initiated by applying a the conversion is initiated by asserting AuxSPI_csb, and data rising edge to the Aux_SPI_CS pin. A rising edge on the retrieval is accomplished through the SPI interface (data Aux_SPI_DO pin indicates that a conversion is done. Supplying retrieval is similar to the default operation). The AuxSPI_csb a clock to the Aux_SPI_CLK then outputs data on the can be configured to initiate the conversion of either one of the Aux_SPI_DO pin, MSB first. AuxADCs. This mode is configured by setting the AuxSPI CONTROLLER AD986x enable register bit [Register 0x22, Bit 7]. SPI_CS[x] SPI_CS SPI_CLK SPI_CLK An optional auxiliary serial port interface (AuxSPI) can be used SPI_SDIO to access an AuxADC. The AuxSPI can initiate an AuxADC SPI_DI conversion and can be used to retrieve the data. The AuxSPI 03606-0-006 can be configured to allow dedicated control of one of the Figure 75. Diagram to Connect 3-Wire SPI to a 4-Wire SPI Controller Rev. 0 | Page 28 of 52 AD9861 Figure 76 shows a timing diagram of the AuxSPI when it is used to control and access an AuxADC. Figure 77 shows the timing for each of the three AuxADC modes of operation. 12 3 AUXSPI_CS AUXSPI_CLK D D D AUXSPI_SDO 9 8 0 1. AUXADC CONVERSION START SIGNAL 2. AUXADC CONVERSION DONE 3. AUXADC OUTPUT UDATE (MSB) 03606-0-021 Figure 76. Timing Diagram of AuxSPI t = t CONVERSION C NORMAL SPI READOUT 16 SPI CLK 16 SPI CLK 16 SPI CLKs USED TO CONFIGURE AND 16 SPI CLKs USED TO READ BACK INITIATE A START CONVERSION 8 REGISTER BITS EXTERNAL START COVERT BIT AND SPI READOUT MODE EXTERNAL PIN USED TO INITIATE A START CONVERSION 16 SPI CLKs USED TO READ BACK 8 REGISTER BITS READOUT MODE WITH AUXILIARY SPI EXTERNAL PIN USED TO INITIATE A START CONVERSION 8-BIT SERIAL OUTPUT READOUT MODE WITH AUXILIARY SPI CYCLE TIME = t + 8 SPI CLK C EXTERNAL START COVERT BIT AND SPI READOUT MODE CYCLE TIME = t + 16 SPI CLK C NORMAL SPI READOUT CYCLE TIME = 16 SPI CLK + t + 16 SPI CLK C 03606-0-007 Figure 77. AuxADC Data Cycle Times for Various Readout Methods Rev. 0 | Page 29 of 52 AD9861 Flexible I/O Interface Options DIGITAL BLOCK The AD9861 can accommodate various data interface transfer The AD9861 digital block allows the device to be configured in options (flexible I/O). The AD9861 uses two 10-bit buses, an various timing and operation modes. The following sections upper bus (U10) and a lower bus (L10), to transfer the dual- discuss the flexible I/O interfaces, the clock distribution block, channel 10-bit ADC data and dual-channel 10-bit DAC data by and the programming of the device through mode pins or SPI means of interleaved data, parallel data, or a mix of both. Table 11 registers. shows the different I/O configurations of the modes depending on half-duplex or full-duplex operation. Table 12 and Table 13 summarize the pin configurations versus the modes. Table 11. Flexible Data Interface Modes Mode Concurrent Tx + Rx Mode Name Tx Only Mode (Half-Duplex) Rx Only Mode (Half-Duplex) (Full-Duplex) General Notes AD9861 AD9861 Rx Data Rate HD20 Tx_A DATA Rx_A DATA = 1 × ADC Sample Rate U[0:9] L[0:9] Tx_B DATA Rx_B DATA Two 10-Bit Parallel Rx Data L[0:9] U[0:9] DIGITAL DIGITAL Buses Tx/Rx Tx/Rx IFACE1 BACK IFACE1 BACK N/A END END Tx Data Rate OUTPUT CLOCK OUTPUT CLOCK IFACE2 IFACE2 = 1 × ADC Sample Rate OUTPUT CLOCK OUTPUT CLOCK IFACE3 IFACE3 Two 10-Bit Parallel Tx Data 03606-0-008 03606-0-012 Buses HD10 AD9861 AD9861 Rx Data Rate Tx_A/B DATA RxSYNC = 2 × ADC Sample Rate U[0:9] U[9] TxSYNC Rx_A/B DATA One 10-Bit Interleaved Rx L[9] L[0:9] DIGITAL DIGITAL Data Bus Tx/Rx Tx/Rx IFACE1 BACK IFACE1 BACK N/A OUTPUT CLOCK END OUTPUT CLOCK END Tx Data Rate IFACE2 IFACE2 = 2 × ADC Sample Rate OUTPUT CLOCK OUTPUT CLOCK IFACE3 IFACE3 One 10-Bit Interleaved Tx 03606-0-009 03606-0-013 Data Bus FD AD9861 AD9861 AD9861 Rx Data Rate Tx_A/B DATA Tx_A/B DATA = 2 × ADC Sample Rate U[0:9] U[0:9] U[0:9] Rx_A/B DATA Rx_A/B DATA One 10-Bit Interleaved Rx L[0:9] L[0:9] L[0:9] DIGITAL DIGITAL DIGITAL Data Bus TxSYNC TxSYNC IFACE1 BACK IFACE1 BACK IFACE1 BACK OUTPUT CLOCK END OUTPUT CLOCK END OUTPUT CLOCK END Tx Data Rate IFACE2 IFACE2 IFACE2 = 2 × ADC Sample Rate OUTPUT CLOCK OUTPUT CLOCK OUTPUT CLOCK IFACE3 IFACE3 IFACE3 One 10-Bit Interleaved Tx 03606-0-010 03606-0-014 03606-0-016 Data Bus Rx Data Rate Clone AD9861 AD9861 Tx_A/B DATA Rx_A DATA = 1 × ADC Sample Rate U[0:9] U[0:9] TxSYNC Rx_B DATA Two 10-Bit Parallel Rx Data L[9] L[0:9] DIGITAL DIGITAL Buses Tx/Rx Tx/Rx IFACE1 BACK IFACE1 BACK OUTPUT CLOCK END OUTPUT CLOCK END Tx Data Rate IFACE2 IFACE2 N/A = 2 × ADC Sample Rate OUTPUT CLOCK OUTPUT CLOCK IFACE3 IFACE3 One 10-Bit Interleaved Tx 03606-0-011 03606-0-015 Data Bus Requires SPI Interface to Configure; Similar to AD9860 Data Interface Rev. 0 | Page 30 of 52 AD9861 Table 12 describes AD9861 pin function (when mode pins are used) relative to I/O mode, and for half-duplex modes whether transmitting or receiving. Table 12. AD9861 Pin Function vs. Interface Mode (No SPI Cases) Mode Name U10 L10 IFACE1 IFACE2 IFACE3 FD Interleaved Tx Data Interleaved Rx Data TxSYNC Buffered Rx Clock Buffered Tx Clock HD10 Interleaved Tx Data MSB = TxSYNC Rx 20 Buffered Tx Clock Tx/ = Tied High 10/ Pin Control Tied High Rx Others = Three-state (Tx/ = High) HD10 MSB = RxSYNC Interleaved Rx Data Rx 20 Buffered Rx Clock Tx/ = Tied Low 10/ Pin Control Tied High Rx Others = Three-state (Tx/ = Low) HD20 Tx_A Data Tx_B Data Rx 20 Buffered Tx Clock Tx/ = Tied High 10/ Pin Control Tied Low Rx (Tx/ = High) HD20 Rx_B Data Rx_A Data Rx 20 Buffered Rx Clock Tx/ = Tied Low 10/ Pin Control Tied Low Rx (Tx/ = Low) Clone Mode Clone mode not available without SPI. (Tx/Rx = High) Clone Mode Clone mode not available without SPI. Rx (Tx/ = Low) Table 13 describes AD9861 pin function (when SPI programming is used) relative to flexible I/O mode, and for half-duplex modes whether transmitting or receiving. Table 13. AD9861 Pin Function vs. Interface Mode (Configured through the SPI Registers) Mode Name U10 L10 IFACE1 IFACE2 IFACE3 FD Interleaved Tx Data Interleaved Rx Data TxSYNC Buffered System Buffered Tx Clock Clock HD10, Tx Mode Interleaved Tx Data MSB = TxSYNC Rx Optional Buffered Buffered Tx Clock Tx/ = Tied High Rx Others = Three-state System Clock (Tx/ = High) HD10, Rx Mode MSB = RxSYNC Interleaved Tx Data Rx Optional Buffered Buffered Rx Clock Tx/ = Tied Low Rx Other = Three-state System Clock (Tx/ = Low) HD20, Tx Mode Tx_A Data Tx_B Data Rx Optional Buffered Buffered Tx Clock Tx/ = Tied High Rx System Clock (Tx/ = High) HD20, Rx Mode Rx_B Data Rx_A Data Rx Optional Buffered Buffered Rx Clock Tx/ = Tied Low Rx System Clock (Tx/ = Low) Clone Mode , Interleaved Tx Data MSB = TxSYNC Rx Optional Buffered Buffered Tx Clock Tx/ = Tied High Tx Mode Others = Three-state System Clock Rx (Tx/ = High) Clone Mode , Rx_B Data Rx_A Data Rx Optional Buffered Buffered Rx Clock Tx/ = Tied Low Rx Mode System Clock Rx (Tx/ = Low) Summary of Flexible I/O Modes The following notes provide a general description of the FD FD Mode mode configuration. For more information, refer to Table 16. The full-duplex (FD) mode can be configured by using mode Note the following about the Tx path in FD mode: pins or with SPI programming. Using the SPI allows additional configuration flexibility of the device. • Interpolation rate of 2× or 4× can be programmed with mode pins or SPI. FD mode is the only mode that supports full-duplex, receive, and transmit concurrent operation. The upper 10-bit bus (U10) • Max DAC update rate = 200 MSPS. is used to accept interleaved Tx data, and the lower 10-bit bus Max Tx input data rate = 80 MSPS/channel (160 MSPS (L10) is used to output interleaved Rx data. Either the Rx path interleaved). or the Tx path (or both) can be independently powered down • TxSYNC is used to direct Tx input data. using either (or both) the RxPwrDwn and TxPwrDwn pins. FD TxSYNC = high indicates channel Tx_A data. mode requires interpolation of 2× or 4×. TxSYNC = low indicates channel Tx_B data. Rev. 0 | Page 31 of 52 AD9861 • Buffered Tx clock output (from IFACE3 pin) equals 2× the • Max ADC sampling rate = 50 MSPS (AD9861-50) or DAC update rate; one rising edge per interleaved Tx sample. 80 MSPS (AD9861-80). Note the following about the Rx path in FD mode: • Output data rate = 2× ADC sample rate. • ADC CLK Div register can be used to divide down the • Interleaved Rx data output from L10 bus. clock driving the ADC, which accepts up to 50 MHz • Rx_A output when IFACE2 (or RxSYNC) logic level = low. (AD9861-50) or up to 80 MHz (AD9861-80). Rx_B output when IFACE2 (or RxSYNC) logic level = high. • Max ADC sampling rate = 50 MSPS (AD9861-50) or HD20 Mode 80 MSPS (AD9861-80). The half-duplex 20-bit parallel output, HD20, can be configured • The Rx path output data rate is 2× the ADC sample rate using mode pins or through SPI programming. (interleaved). HD20 mode supports half-duplex only operations and can • Rx_A output when IFACE2 logic level = low. interface to a single 20-bit data bus (two parallel 10-bit buses). Rx_B output when IFACE2 logic level = high. Both the U10 and L10 buses are used on the AD9861. The logic level of the Tx/Rx selector (controlled through IFACE1 pin) is HD10 Mode used to configure the buses as Rx outputs (during Rx operation) The half-duplex, 10-bit interleaved outputs mode, HD10 can be or as Tx inputs (during Tx operation). A single pin is used to configured using mode pins or the SPI. output the clocks for Rx and Tx data latching (from the IFACE3 pin) switching, depending on which path is enabled. HD10 mode supports half-duplex only operations and can interface to a single 10-bit data bus with independent Rx and Tx The following notes provide a general description of the HD20 synchronization pins (RxSYNC and TxSYNC). Both the U10 mode configuration. For more information, refer to Table 16. and L10 buses are used on the AD9861, but the logic level of the Tx/Rx selector (controlled through IFACE1 pin) is used to Note the following about the Tx Path in HD20 mode: disable and three-state the unused bus, allowing U10 and L10 to • Interpolation rate of 1×, 2×, or 4× can be programmed with be tied together. The MSB of the unused bus acts as the RxSYNC mode pins or SPI. (during Rx operation) or TxSYNC (during Tx operation). A single pin is used to output the clocks for Rx and Tx data • Max DAC update rate = 200 MSPS. latching (from the IFACE3 pin) switching, depending on which Max Tx input data rate = 160 MSPS/channel with bypassed path is enabled. HD10 mode requires interpolation of 2× or 4×. interpolation filters, 100 MSPS for 2× interpolation or 50 MSPS for 4× interpolation. The following notes provide a general description of the HD10 mode configuration. For more information, refer to Table 16. • Tx_A DAC data is accepted from the U10 bus; Tx_B DAC data is accepted from the L10 bus. Note the following about the Tx path in HD10 mode: Note the following about the Rx path in HD20 mode: • Interpolation rate of 2× or 4× can be programmed with mode pins or SPI. • ADC CLK Div register can be used to divide down the clock driving the ADC, which accepts up to 50 MHz • Interleaved Tx data accepted on U10 bus, L10 bus MSB acts (AD9861-50) or up to 80 MHz (AD9861-80). as TxSYNC. • Max ADC sampling rate = 50 MSPS (AD9861-50) or • Max DAC update rate = 200 MSPS. 80 MSPS (AD9861-80). Max Tx input data rate = 80 MSPS/channel (160 MSPS interleaved). • The Rx_A output data is output on L10 bus; the Rx_B output data is output on U10 bus. • TxSYNC is used to direct Tx input data. TxSYNC = high indicates channel Tx_A data. Clone Mode TxSYNC = low indicates channel Tx_B data. An interface mode provides a similar interface to the AD9860 Note the following about the Rx path in HD10 mode: when used in half-duplex mode. This mode is referred to as clone mode and requires SPI to configure. • ADC CLK Div register can be used to divide down the clock driving the ADC, which accepts up to 50 MHz Clone mode provides a parallel Rx data output (20 bits) while in (AD9861-50) or up to 80 MHz (AD9861-80). Rx mode, and accepts interleaved Tx data (10-bit) while in Tx Rev. 0 | Page 32 of 52 AD9861 mode. Both the U10 and L10 buses are used on the AD9861. • Max ADC sampling rate = 50 MSPS (AD9861-50) or The logic level of the Tx/ selector (controlled through the Rx 80 MSPS (AD9861-80). IFACE1 pin) is used to configure the buses for Rx outputs • Output data rate = ADC sample rate, that is, two 10-bit (during Rx operation) or as Tx inputs (during Tx operation). A parallel outputs per one buffer Rx clock output cycle. single pin is used to output the clocks for Rx and Tx data latching (from the IFACE3 pin), depending on which path is • The Rx_A output data is output on L10 bus; the Rx_B enabled. Clone mode requires interpolation of 2× or 4×. output data is output on U10 bus. The following notes provide a general description of the clone Configuring with Mode Pins mode configuration. For more information, refer to Table 16. The flexible interface can be configured with or without the SPI, although more options and flexibility are available when using Note the following about the Tx path in clone mode: the SPI to program the AD9861. Mode pins can be used to power down sections of the device, reduce overall power consump- • Interpolation rate of 2× or 4× can be programmed with tion, configure the flexible I/O interface, and program the mode pins or SPI. interpolation setting. The SPI register map, which provides • Max DAC update rate = 200 MSPS. many more options, is discussed in the Configuring with SPI Max Tx input data rate = 80 MSPS/channel (160 MSPS section. interleaved). Mode Pins/Power-Up Configuration Options • TxSYNC is used to direct Tx input data. Various options are configurable at power-up through mode TxSYNC = high indicates channel Tx_A data. pins, and also through control pins for power-down modes. The TxSYNC = low indicates channel Tx_B data. logic value of the configuration mode pins are latched when the device is brought out of reset (rising edge of ). The mode RESET • Buffered Tx clock output (from IFACE3 pin) uses one rising edge per interleaved Tx sample. pin names and their functions are shown in Table 14. Table 15 provides a detailed description of the mode pins. Note the following about the Rx path in clone mode: • ADC CLK Div register can be used to divide down the clock driving the ADC, which accepts up to 50 MHz (AD9861-50) or up to 80 MHz (AD9851-80). Table 14. Mode Pin Names and Functions Pin Name Duration Function RxPwrDwn Permanent When high, digital clocks to Rx block are disabled. Analog circuitry that require <10 µs to power up are powered off. TxPwrDwn Permanent When high, digital clocks to Tx block are disabled (PLL remains powered to maintain output clock with an optional SPI shut off). Analog circuitry that require <10 µs to power up are powered off. Tx/Rx (IFACE1) Permanent only for When high, digital clocks to Tx block are disabled (PLL remains powered to maintain HD Flex I/O interface output clock with an optional SPI shutoff). Tx analog blocks remain powered up unless Tx_PwrDwn is asserted. When low, digital clocks to Rx block are disabled. Rx analog circuitry remain powered up unless Rx_PwrDwn is asserted. ADC_LO_PWR Defined at Reset or When enabled, this bit scales the ADC power-down by 40%. Power-Up SPI_Bus_Enable Defined at Reset or This function is controlled through the SPI_CS pin. This pin must remain low to maintain (SPI_CS) Power-Up mode pin functionality (the SPI port remains nonfunctional). This pin must be high when coming out of reset to enable the SPI. FD/HD Defined at Reset or Configures the flex I/O for FD or HD mode. This control applies only if the SPI bus is Power-Up disabled. 10/20 only valid for Defined at Reset or If the flex I/O bus is in HD mode, this bit is used to configure parallel or interleaved data Power-Up mode. This control applies only if the SPI bus is disabled. HD mode Interp0 and Interp1 Defined at Reset or The Interp1 and Interp0 bits configure the PLL and the interpolation rate to 1× [00], 2× Power-Up [01], or 4× [10]. This control applies only if the SPI bus is disabled. Rev. 0 | Page 33 of 52 AD9861 Table 15. Mode Pin Names and Descriptions Pin Name Description ADC_LO_PWR ADC Low Power Mode Option. ADC_LO_PWR is latched during the rising edge of RESET. Logic low results in ADC operation at nominal power mode. Logic high results in ADC consuming 40% less power than the nominal power mode. FD/HD (SDO) For Flex I/O Configuration, this control applies only if the SPI bus is disabled. FD/HD (SDO) is latched during the rising edge of RESET. Logic low identifies that the DUT flex I/O port will be configured for half-duplex operation. 10/20 (IFACE2) is also latched during the rising edge of RESET to identify interleaved data mode or parallel data modes. Logic low indicates that the flex I/O will configure itself for parallel data mode. Logic high indicates that the flex I/O will configure itself for interleaved data mode. 20 20 10/ For flex I/O Configuration, The 10/ pin control applies only if the SPI bus is disabled and the device is 20 configured for HD mode. 10/ is latched during the rising edge of RESET. 20 10/ (IFACE2) is used to identify interleaved data mode or parallel data modes. Logic low indicates that the flex I/O will configure itself for HD20 mode. Logic high indicates that the flex I/O will configure itself for HD10 mode. SPI_Bus_Enable (SPI_CS) SPI_CS is latched during the rising edge of RESET. Logic low results in the SPI being disabled and SPI_DIO, SPI_CLK and SPI_SDO act as mode pins. Logic high results in the SPI being fully operational, and some of the mode pins are disabled. Interp0 and Interp1 Interpolation/PLL Factor Configuration. This control applies only if the SPI bus is disabled. SPI_DIO (Interp1) and SPI_CLK (Interp0) configure the Tx path for 1× [00], 2× [01], or 4× [10] interpolation and also enable the PLL of the same multiplication factor. RxPwrDwn Power-Down Control. RxPwrDwn logic level controls the power-down function of the Rx path. Logic low results in the Rx path operating at normal power levels. Logic high disables the ADC clock and disables some bias circuitry to reduce power consumption. TxPwrDwn Power-Down Control. TxPwrDwn logic level controls the power-down function of the Tx path. Logic low results in the Tx path operating at normal power levels. Logic high disables the DAC clocks and disables some bias circuitry to reduce power consumption. Tx/Rx Power-Down Control. Tx/Rx pin enables the appropriate Tx or Rx path in the half-duplex mode. A logic low disables the Tx digital clock and the I/O bus is configured as an output or three-stated. A logic high disables the Rx digital clocks and the I/O bus is configured as high impedance inputs. Rev. 0 | Page 34 of 52 AD9861 Configuring with SPI The flexible interface can be configured with register settings. Using the register allows more device programmability. Table 16 shows the required register writes to configure the AD9861 for FD, optional FD, HD20, optional HD20, HD10, optional HD10, and clone mode. Note that for modes that use interleaved data buses, enabling 2× or 4× interpolation is required. Table 16. Registers for Configuring SPI Register Address Setting Description FD, Mode 1 Register 0x01 [7:5] [000]; clk_mode—Configures timing mode. Register 0x14 [4] High SpiFDnHD—Configures FD mode. Register 0x14 [2] High SpiB10n20—Configures FD mode. Register 0x13 [1:0] [01] or [10] Interpolation Control—Configures 2× or 4× interpolation. Optional FD, Mode 2 Register 0x01 [7:5] [001] clk_mode—Configures timing mode. Register 0x14 [4] High SpiFDnHD—Configures FD mode. Register 0x14 [2] High SpiB10n20—Configures FD mode. Register 0x13 [1:0] [01] or [10] Interpolation Control—Configures 2× or 4× interpolation. HD20, Mode 4 Register 0x01 [7:5] [000]; clk_mode—Configures timing mode. Register 0x14 [4] Low SpiFDnHD—Configures HD mode. Register 0x14 [2] Low SpiB10n20—Configures HD20 mode. Register 0x13 [1:0] [00], [01] or [10] Interpolation Control—Configures 1×, 2×, or 4× interpolation. Optional HD20, Mode 5 Register 0x01 [7:5] [011] clk_mode—Configures timing mode. Register 0x14 [4] Low SpiFDnHD—Configures HD mode. Register 0x14 [2] Low SpiB10n20—Configures HD20 mode. Register 0x13 [1:0] [00], [01] or [10] Interpolation Control—Configures 1×, 2×, or 4× interpolation. HD10, Mode 7 Register 0x01 [7:5] [000] clk_mode—Configures timing mode. Register 0x14 [4] Low SpiFDnHD—Configures HD mode. Register 0x14 [2] High SpiB10n20—Configures HD10 mode. Register 0x13 [1:0] [01] or [10] Interpolation Control—Configures 2× or 4× interpolation. Optional HD10, Mode 8 Register 0x01 [7:5] [101] clk_mode—Configures timing mode. Register 0x14 [4] Low SpiFDnHD—Configures HD mode. Register 0x14 [2] High SpiB10n20—Configures HD10 mode. Register 0x13 [1:0] [01] or [10] Interpolation Control—Configures 2× or 4× interpolation. Clone, Mode 10 Register 0x01 [7:5] [111] clk_mode—Configures timing mode. Register 0x14 [0] High SpiClone—Configures clone mode. Register 0x13 [1:0] [01] or [10] Interpolation Control—Configures 2× or 4× interpolation. Rev. 0 | Page 35 of 52 AD9861 SPI Register Map Registers 0x00 to 0x29 of the AD9861 provide flexible operation of the device. The SPI allows access to many configurable options. Detailed descriptions of the bit functions are found in Table 18. Table 17. Register Map Reg. Name Addr 7 6 5 4 3 2 1 0 General 0x00 SDIO BiDir LSB First Soft Reset Clock Mode 0x01 clk_mode[2:0] Enable IFACE2 Inv clkout clkout (IFACE3) Power-Down 0x02 Tx Analog TxDigital RxDigital PLL Power- PLL Output Down Disconnect RxA Power-Down 0x03 Rx_A Analog Rx_A DC Bias RxB Power-Down 0x04 Rx_B Analog Rx_B DC Bias Rx Power-Down 0x05 Rx Analog Bias RxRef DiffRef VREF Rx Path 0x06 Rx_A Twos Rx_A Clk Complement Duty Rx Path 0x07 Rx_B Twos Rx_B Clk Complement Duty Rx Path 0x08 Rx Ultralow Rx Ultralow Power Control Power Control Rx path 0x09 Rx Ultralow Rx Ultralow Rx Ultralow Power Control Power Control Power Control Rx Path 0x0A Rx Ultralow Rx Ultralow Rx Ultralow Power Control Power Control Power Control Tx Path 0B DAC A Offset [9:2] Tx Path 0C DAC A Offset [1:0] DAC A Offset Direction Tx Path 0D DAC A Coarse Gain Control DAC A Fine Gain [5:0] Tx Path 0E DAC B Offset [9:2] Tx Path 0F DAC B Offset [1:0] DAC B Offset Direction Tx Path 10 DAC B Coarse Gain Control DAC B Fine Gain [5:0] Tx Path 11 TxPGA Gain [7:0] Tx Path 12 TxPGA Slave TxPGA Fast Enable Update I/O Configuration 13 Tx Twos Rx Twos Tx Inverse Interpolation Control [1:0] Complement Complement Sample I/O Configuration 14 Dig Loop On SpiFDnHD SpiTxnRx SpiB10n20 SPI IO Control SpiClone Clock 15 PLL Bypass ADC Clock Div Alt Timing Mode PLL Div5 PLL Multiplier [2:0] Clock 16 PLL to IFACE2 PLL Slow Auxiliary 17 AuxDAC A FS [1:0] AuxDAC B FS [1:0] AuxDAC C FS [1:0] AuxADC Ref AuxADC Ref Converters Enable FS AuxADC 18 Start Average Number of AuxADC A Samples [2:0] AuxADC A AuxADC 19 Start Average Number of AuxADC B Samples [2:0] AuxADC B AuxADC 1A AuxADC A2 [1:0] AuxADC 1B AuxADC A2 [9:2] AuxADC 1C AuxADC A1 [1:0] AuxADC 1D AuxADC A1 [9:2] AuxADC 1E AuxADC B [1:0] AuxADC 1F AuxADC B [9:2] AuxADC 22 AuxSPI Enable Sel 2not1 Refsel B Start B Refsel A Select A Start A AuxADC 23 AuxADC Clock Div[1:0] AuxDAC 24 AuxDAC A [7:0] 25 AuxDAC B [7:0] 26 AuxDAC C [7:0] 28 Slave Enable Update C Update B Update A 29 AuxDAC C Sync AuxDAC B Sync AuxDAC A Sync Power-Up C Power-Up B Power-Up A TxPwrDwn TxPwrDwn TxPwrDwn Rev. 0 | Page 36 of 52 AD9861 Table 18. Register Bit Descriptions Register Bit Description Register 0: General Bit 7: SDIO BiDir (Bidirectional) Default setting is low, which indicates that the SPI serial port uses dedicated input and output lines (4-wire interface), SDIO and SDO pins, respectively. Setting this bit high configures the serial port to use the SDIO pin as a bidirectional data pin. Bit 6: LSB First Default setting is low, which indicates MSB first SPI port access mode. Setting this bit high configures the SPI port access to LSB first mode. Bit 5: Soft Reset Writing a high to this register resets all the registers to their default values and forces the PLL to relock to the input clock. The soft reset bit is a one-shot register, and is cleared immediately after the register write is completed. Register 1: Clock Mode Bits 7–5: Clk Mode These bits represent the clocking interface for the various modes. Setting 000 is default. Setting 111 is used for clone mode. Refer to the Summary of Flexible I/O Modes section for definition of clone mode. Setting Mode 000 Standard FD, HD10, HD20 Clock (Modes 1, 4, 7) 001 Optional FD timing (Mode 2) 010 Not Used 011 Optional HD20 timing (Mode 5) 100 Not Used 101 Optional HD10 timing (Mode 8) 110 Not Used 111 Clone Mode (Mode 10) Bit 2: Enable IFACE2 clkout Enables the IFACE2 port to be an output clock. Also inverts the IFACE2 output clock in full-duplex mode. Bit 1: Inv clkout (IFACE3) Invert the output clock on IFACE3. Register 2: Power-Down Bits 7–5: Tx Analog (Power- Three options are available to reduce analog power consumption for the Tx channels. The first two Down) options disable the analog output from Tx Channel A or B independently, and the third option disables the output of both channels and reduces the power consumption of some of the addi- tional analog support circuitry for maximum power savings. With all three options, the DAC bias current is not powered down so recovery times are fast (typically a few clock cycles). The list below explains the different modes and settings used to configure them. Power-Down Option Bits Setting [7:5] Power-Down Tx A Channel Analog Output [1 0 0] Power-Down Tx B Channel Analog Output [0 1 0] Power-Down Tx A and Tx B Analog Outputs [1 1 1] Bit 4: Tx Digital (Power-Down) Default setting is low, which enables the transmit path digital to operate as programmed through other registers. By setting this bit high, the digital blocks are not clocked to reduce power consumption. When enabled, the Tx outputs are static, holding their last update values. Bit 3: Rx Digital (Power-Down) Setting this bit high powers down the digital section of the receive path of the chip. Typically, any unused digital blocks are automatically powered down. Bit 2: PLL Power-Down Setting this register bit high forces the CLKIN multiplier to a power-down state. This mode can be used to conserve power or to bypass the internal PLL. To operate the AD9861 when the PLL is bypassed, an external clock equal to the fastest on-chip clock is supplied to the CLKIN. Bit 1: PLL Output Disconnect Setting this register bit high disconnects the PLL output from the clock path. If the PLL is enabled, it locks or stays locked as normal. Register 3/4: Rx Power-Down Bit 7: Rx_A Analog/ Either ADC or both ADCs can be powered down by setting the appropriate register bit high. The Rx_B Analog (Power-Down) entire analog circuitry of Rx channel is powered down, including the differential references, input buffer, and the internal digital block. The band gap reference remains active for quick recovery. Bit 6: Rx_A DC Bias/ Setting either of these bits high powers down the input common-mode bias network for the Rx_B DC Bias (Power-Down) respective channel and requires an input signal to be properly dc-biased. By default, these bits are low, and the Rx inputs are self-biased to approximately AVDD/2 and accept an ac-coupled input. Register 5: Rx Power-Down Bit 7: Rx Analog Bias (Power- Setting this bit high powers down all analog bias circuits related to the receive path (including the Down) differential reference buffer). Because bias circuits are powered down, an additional power saving, but also a longer recovery time relative to other Rx power-down options, will result. Rev. 0 | Page 37 of 52 AD9861 Register Bit Description Bit 6: RxREF (Power-Down) Setting this register bit high powers down internal ADC reference circuits. Powering down these circuits provides additional power saving over other power-down modes. The Rx path wake-up time depends on the recovery of these references typically of the order of a few milliseconds. Bit 5: DiffRef (Power-Down) Setting this bit high powers down the ADC’s differential references, REFT and REFB. Recovery time depends on the value of the REFT and REFB decoupling capacitors. Bit 4: VREF (Power-Down) Setting this register bit high powers down the ADC reference circuit, VREF. Powering down the Rx band gap reference allows an external reference to drive the VREF pin setting full-scale range of the Rx paths. Registers 6/7: Rx Path Bit 5: Rx_A Twos Complement/ Default data format for the Rx data is straight binary. Setting this bit high generates twos Rx_B Twos Complement complement data. Bit 4: Rx_A Clk Duty/Rx_B Clk Setting either of these bits high enables the respective channels on-chip duty cycle stabilizer (DCS) Duty circuit to generate the internal clock for the Rx block. This option is useful for adjusting for high speed input clocks with skewed duty cycle. The DCS mode can be used with ADC sampling frequencies over 40 MHz. Registers 8/9/A: Rx Path Rx Ultralow Power Control Bits Set all bits high, in combination with asserting the ADC_LO_PWR pin, to reduce the power consumption of the Rx path by a fourth of normal Rx path power consumption. Registers 0B/0C/0E/0F: Tx Path DAC A/DAC B Offset These 10-bit, twos complement registers control a dc current offset that is combined with the Tx A or Tx B output signal. An offset current of up to ±12% IOUTFS (2.4 mA for a 20 mA full-scale output) can be applied to either differential pin on each channel. The offset current can be used to compensate for offsets that are present in an external mixer stage, reducing LO leakage at its output. The default setting is 0x00, no offset current. The offset current magnitude is set by using the lower nine bits. Setting the MSB high adds the offset current to the selected differential pin, while an MSB low setting subtracts the offset value. DAC A/DAC B Offset Direction This bit determines to which of the differential output pins for the selected channel the offset current is applied. Setting this bit low applies the offset to the negative differential pin. Setting this bit high applies the offset to the positive differential pin. Registers 0D/10: Tx Path Bits 7, 6: DAC A/DAC B Coarse These register bits scale the full-scale output current (IOUTFS) of either Tx channel independently. Gain Control IOUT of the Tx channels is a function of the RSET resistor, the TxPGA setting, and the coarse gain control setting. 00 Output current scaling by 1/11 01 Output current scaling by ½ 10 No output current scaling 11 No output current scaling Bits 5–0: DAC A/DAC B Fine Gain The DAC output curve can be adjusted fractionally through the gain trim control. Gain trim of up to ±4% can be achieved on each channel individually. The gain trim register bits are a twos complement attention control word. MSB, LSB 100000 Maximum positive gain adjustment 111111 Minimum positive gain adjustment 000000 No adjustment (default) 000001 Minimum negative gain adjustment 011111 Maximum negative gain adjustment Register 11: Tx Path Bits 0–7: TxPGA Gain This 8-bit, straight binary (Bit 0 is the LSB, Bit 7 is the MSB) register controls for the Tx programmable gain amplifier (TxPGA). The TxPGA provides a 20 dB continuous gain range with 0.1 dB steps (linear in dB) simultaneously to both Tx channels. By default, this register setting is 0xFF. MSB, LSB 0000 0000 Minimum gain scaling –20 dB 1111 1111 Maximum gain scaling 0 dB Register 12: Tx Path Bit 6: TxPGA Slave Enable The TxPGA gain is controlled through register TxPGA gain setting and, by default, is updated immediately after the register write. If this bit is set, the TxPGA gain update is synchronized with the falling edge of a signal applied to the TxPwrDwn pin and is enabled during the wake-up from power-down. Rev. 0 | Page 38 of 52 AD9861 Register Bit Description Bit 4: TxPGA Fast Update (Mode) The TxPGA fast bit controls the update speed of the TxPGA. When fast update mode is enabled, the TxPGA provides fast gain settling within a few clock cycles, which may introduce spurious signals at the output of the Tx path. The default setting for this bit is low, and the TxPGA gives a smooth transition between gain settings. Fast mode is enabled when this bit is set high. Register 13: I/O Configuration Bit 7: Tx Twos Complement The default data format for Tx data is straight binary. Set this bit high when providing twos complement Tx data. Bit 6: Rx Twos Complement The default data format for Rx data is straight binary. Set this bit high when providing twos complement Rx data. Bit 5: Tx Inverse Sample By default, the transmit data is sampled on the rising edge of the CLKOUT. Setting this bit high changes this, and the transmit data is sampled on the falling edge. Bits 1,0: Interpolation Control These register bits control the interpolation rate of the transmit path. The default settings are both bits low, indicating that both interpolation filters are bypassed. The MSB and LSB are Address Bits 1 and 0, respectively. Setting binary 01 provides an interpolation rate of 2×; binary 10 provides an interpolation rate of 4×. Register 14: I/O Configuration Bit 5: Dig Loop On When enabled, this bit enables a digital loop back mode. The digital loop-back mode provides a means of testing digital interfaces and functionality at the system level. In digital loop-back mode, the full-duplex interface must be enabled. (Refer to the Flexible I/O Interface Options section.) The device accepts digital input from the bus according to the FD mode timing and uses the Tx digital path (with enabled interpolation and other digital settings); the processed data is then output from the Rx path bus. Bit 4: SPI_FDnHD Control bit to configure full-duplex (high) or half-duplex (low) interface mode. This register, in combination with the SpiB10n20 register, configures the interface mode of FD, HD10, or HD20. The register setting is ignored for clone mode operation. By default, this register is set high, and the device is in FD mode. Bit 3: SpiTxnRx Control bit used for toggling between transmit or receive mode for the half-duplex clock modes. High represents Tx and low represents Rx. Bit 2: SpiB10n20 Control bit for 10-bit or 20-bit modes. High represents 10-bit mode and Low represents 20-bit mode. Bit 1: SPI IO Control Use in conjunction with SpiTxnRx [Register14, Bit 3] to override external TxnRx pin operation. Bit 0: SpiClone Set high when in clone mode (see the Flexible I/O Interface Options section for definition of clone mode). Clk_mode should also be set to binary 111, i.e., [Register 01[7:5] = 111. Register 15: Clock Bit 7: PLL_Bypass Setting this bit high bypasses the PLL. When bypassed, the PLL remains active. Bits 5: ADC Clock Div By default, the ADCs are driven directly from CLKIN in normal timing operation or from the PLL output clock in the alternative timing operation. This bit is used to divide the source of the ADC clock prior to the ADCs. The default setting is low and performs no division. Setting this bit high divides the clock by 2. Bit 4: Alt Timing Mode The timing table in the data sheet describes two timing modes: the normal timing operation mode and the alternative timing operation mode. The default configuration is normal timing mode and the CLKIN drives the Rx path. In alternative timing mode, the PLL output is used to drive the Rx path. The alternative operation mode is configured by setting this bit high. Bit 3: PLL Div5 The output of the PLL can be divided by 5 by setting this bit high. By default, the PLL directly drives the Tx digital path with no division of its output. Bits 2–0: PLL Multiplier These bits control the PLL multiplication factor. A default setting is binary 000, which configures the PLL to 1× multiplication factor. This register, in combination with the PLL Div5 register, sets the PLL output frequency. The programmable multiplication factors are 000 1× 001 2× 010 4× 011 8× 100 16× 101 – 111 not used Register 16: Clock Bit 5: PLL to IFACE2 Setting this bit high switches the IFACE2 output signal to the PLL output clock. It is valid only if Register 0x01, Bit 2 is enabled or if full-duplex mode is configured. Bit 2: PLL Slow Changes the PLL loop bandwidth and changes the profile of the phase noise generated from the PLL clock. Rev. 0 | Page 39 of 52 AD9861 Register Bit Description Register 17: Auxiliary Converters Bits 7–2: AuxDAC A FS/AuxDAC B These register bits independently scale the full-scale output voltage for the AuxDACs. If the full- FS/AuxDAC C FS scale voltage is programmed to a value greater than PLL_VDD – 0.2 V, the AuxDAC becomes nonlinear in this region. MSB, LSB AuxDAC Full-Scale Output Voltage 00 3.0 V 01 3.3 V 10 2.5 V 11 2.7 V Bit 1: AuxADC Ref Enable This bit enables the on-chip, supply independent reference for the AuxADC. By default, the AuxADC uses the PLL_AVDD supply for its full-scale voltage level. Bit 0: AuxADC Ref FS When the AuxADC Ref Enable bit is set high, this bit allows the user to select the full-scale value of the AuxADC. A low setting sets the full-scale value to 3.0 V; a high setting sets the full-scale value to 2.5 V. If the full-scale voltage is programmed to a value greater than PLL_VDD – 0.2 V, the AuxADC is not linear in this region. Registers 18/19 : AuxADC Bit 7: Start Average AuxADC A/ These registers are used to initiate a conversion cycle of the AuxADCs for a number of consecutive Start Average AuxADC B samples and then report the average result. The number of consecutive samples is programmed in the number of AuxADC A/AuxADCB samples register. The external pin Aux_SPI_CS can be config- ured to allow it to initiate the start average conversion cycle. The result is placed in the appropriate register corresponding to the AuxADC output [Registers 0x1A to 0x21]. Bit 7: Number of AuxADC A/ These bits control the number of samples that the AuxADC collects and uses to calculate an AuxADC B Samples average value. This register is used in conjunction with the start average AuxADC register. MSB, LSB Number of Samples to Average 000 1 001 2 010 4 011 8 100 16 101 32 110 64 111 Not Used Registers 1A–21: AuxADC These 10-bit, offset binary registers are read-only and store the last corresponding AuxADC output values. The AD9861 has two AuxADC SAR converters: AuxADC A and AuxADC B. AuxADC A has a multiplexed input, which allows the user to select either input by using the Select A register. The 10 bits are broken into two registers, one containing the upper eight bits and the other containing the lower two bits. Register 22: AuxADC Bit 7: AuxSPI (Enable) Enables the AuxSPI, which can be used to initiate a conversion and read back one of the AuxADCs. Bit 6: Sel 2not1 If the auxiliary serial port is used, this bit selects which AuxADC, 1 or 2, uses the dedicated auxiliary serial port. By default (low setting), the auxiliary serial port controls AuxADC A. Setting this bit high allows the auxiliary serial port to control AuxADC B. Bits 5, 2: Refsel B/A By default, the AuxADCs use an external reference applied to the AUX_REF pin. This voltage acts as the full-scale reference for the selected AuxADC. Either AuxADC can use an internally generated reference, which can be a buffered version of the analog supply voltage or a supply independent, 3.0 V or 2.5 V internal reference. To enable use of the internal reference for either of the AuxADCs, set the respective Refsel register high. For internal reference configuration, see Register 17. Bit 1: Select A This bit is used to select which of the two inputs is connected to the AuxADC. By default (setting low), the AUX_ADC_A2 (Aux2 pin) is connected to AuxADC A. Setting the respective bit high connects the AUX_ADC_A1 (Aux1 pin) to AuxADC A. Bit 3, 0: Start B/A Setting either of these bits to high initiates a conversion of the respective AuxADC, A or B. The register bit always reads back a low. Rev. 0 | Page 40 of 52 AD9861 Register Bit Description Register 23: AuxADC Bits 1,0: AuxADC Clock Div The AuxADCs clock can be based on either the clock driving the Rx ADC, or it can be driven from the SPI_CLK. The conversion rate of the AuxADCs should be less than 40 MHz. In order to facilitate a slower speed clock for the AuxADC, these bits are used to divide down the Rx ADC clock prior to driving the AuxADC. The following options are programmable through this register: MSB, LSB AuxADC Sampling Rate 00 Rx ADC Clock/4 01 Rx ADC Clock/2 10 Rx ADC Clock 11 SPI_CLK drives AuxADC Registers 24, 25, 26: AuxDAC AuxDAC A, B, and C Output Three 8-bit, straight binary words are used to control the output of three on-chip AuxDACs. The Control Word AuxDAC output changes take effect immediately after any of the serial writes are completed. The DAC output control words have default values of 0. The smaller programmed output controlled words correspond to lower DAC output levels. Register 28: AuxDAC Bit 7: Slave Enable A low setting (default) updates the AuxDACs after the respective register is written to. To synchronize the AuxDAC outputs to each other, a slave mode can be enabled by setting this bit high and then setting the appropriate update registers high. Bits 2/1/0: Update C, B, and A Setting a high bit to any of these bits initiates an update of the respective AuxDAC, A, B or C, when slave mode is enabled using the slave enable register. The register bit is a one-shot and always reads back a low. Be sure to keep the slave enable bit high when using the AuxDAC synchronization option. Register 29: AuxDAC Bits 7/6/5: AuxDAC C/B/A Sync Setting any of these bits high synchronizes AuxDAC updates only when the TxPwrDwn rising edge TxPwrDwn occurs. This syncronizes the AuxDAC update to the Tx path power-up. Bits 2/1/0: Power Up C, B, and A Setting any of these bits high powers up the appropriate AuxDAC. By default, these bits are low and the AuxDACs are disabled. Rev. 0 | Page 41 of 52 AD9861 PROGRAMMABLE REGISTERS cycle. Phase 2 is the actual data transfer between the AD9861 The AD9861 contains internal registers that are used to configure and the system controller. Phase 2 of the communication cycle the device. A serial port interface provides read/write access to is a transfer of one or two data bytes as determined by the the internal registers. Single-byte or dual-byte transfers are instruction byte. Normally, using one communication cycle in a supported as well as MSB first or LSB first transfer formats. The multibyte transfer is the preferred method; however, single byte AD9861’s serial interface port can be configured as a single pin communication cycles are useful to reduce CPU overhead when I/O (SDIO) or as two unidirectional pins for in/out (SDIO/SDO). register access requires only one byte. An example of this is to The serial port is a flexible, serial communications port, allowing write the AD9861 power-down bits. easy interface to many industry-standard microcontrollers and microprocessors. All data input to the AD9861 is registered on the rising edge of General Operation of the Serial Interface SCLK. All data is driven out of the AD9861 on the falling edge of SCLK. By default, the serial port accepts data in MSB first mode and uses four pins: SEN, SCLK, SDIO, and SDO by default. SEN is a Instruction Byte serial clock enable pin; SCLK is the serial clock pin; SDIO is a The instruction byte contains the information shown in bidirectional data line; and SDO is a serial output pin. Table 19, and the bits are described in detail after the table. SEN is an active low control gating read and write cycles. When Table 19. Instruction Byte SEN is high, SDO and SDIO go into a high impedance state. MSB D6 D5 D4 D3 D2 D1 LSB R/nW 2/n1 A5 A4 A3 A2 A1 A0 SCLK is used to synchronize SPI read and writes at a maximum Byte bit rate of 30 MHz. Input data is registered on the rising edge, R/nW—Bit 7 of the instruction byte determines whether a read and output data transitions are registered on the falling edge. or write data transfer will occur after the instruction byte write. During write operations, the registers are updated after the 16th Logic high indicates a read operation. Logic low indicates a rising clock edge (and 24th rising clock edge for the dual-byte write operation. case). Incomplete write operations are ignored. 2/n1 Byte—Bit 6 of the instruction byte determines the number SDIO is an input data only pin by default. Optionally, a 3-pin of bytes to be transferred during the data transfer cycle of the interface may be configured using the SDIO for both input and communication cycle. Logic high indicates a 2-byte transfer. output operations and three-stating the SDO pin. Refer to the Logic low indicates a 1-byte transfer. SDIO BiDir bit in Register 0x00 (Table 18). A5, A4, A3, A2, A1, A0—Bits 5, 4, 3, 2, 1, and 0 of the SDO is a serial output data pin used for readback operations in instruction byte determine which register is accessed during the 4-wire mode and is three-stated when SDIO is configured for data transfer portion of the communication cycle. For 2-byte bidirectional operation. transfers, this address is the starting byte address. The second There are two phases to a communication cycle with the AD9861. byte address is automatically decremented when the interface is Phase 1 is the instruction cycle, which is the writing of an configured for MSB first transfers. For LSB first transfers, the instruction byte into the AD9861, coincident with the first eight address of the second byte is automatically incremented. SCLK rising edges. The instruction byte provides the AD9861 Table 20. Serial Port Interface Timing serial port controller with information regarding the data Maximum SCLK Frequency (fSCLK) 40 MHz transfer cycle, which is Phase 2 of the communication cycle. The Minimum SCLK High Pulse Width (t) 12.5 ns PWH Phase 1 instruction byte defines whether the upcoming data Minimum SCLK Low Pulse Width (t) 12.5 ns PWL transfer is read or write, the number of bytes in the data transfer Maximum Clock Rise/Fall Time 1 ms (one or two), and the starting register address for the first byte Data to SCLK timing (tDS) 12.5 ns of the data transfer. Data Hold Time (tDH) 0 ns The first eight SCLK rising edges of each communication cycle are used to write the instruction byte into the AD9861. The remaining SCLK edges are for Phase 2 of the communication Rev. 0 | Page 42 of 52 AD9861 Write Operations The SPI write operation uses the instruction header to config- Figure 78 to Figure 80 are examples of writing data into the ure a 1-byte or 2-byte register write using the 2/n1 byte setting. device. Figure 78 shows a 1-byte write with MSB first; Figure 79 The instruction byte followed by the register data is written shows a 2-byte write with MSB first; and Figure 80 shows a serially into the device through the SDIO pin on rising edges of 2-byte write with LSB first. Note the differences between LSB the interface clock, SCLK. The data can be transferred MSB first and MSB first modes: both the instruction header and data are or LSB first depending on the setting of the LSB first register bit. reversed, and the second data byte register location is different. The write operation is the same regardless of SDIO BiDir In the default MSB first mode, the second data byte is written to register setting. a decremented register address. In LSB first mode, the second data byte is written to an incremented register address. t t t t DS H HI CLK t t S DH t LO SEN SCLK DON'T CARE DON'T CARE SDIO DON'T CARE R/W 2/1 A5 A4 A3 A2 A1 A0 D7 D6 D5 D4 D3 D2 D1 D0 DON'T CARE INSTRUCTION HEADER REGISTER DATA 03606-0-022 Figure 78. 1-Byte Serial Register Write in MSB First Mode t HI t t H S t LO t DH t t CLK DS SEN DON'T CARE SCLK DON'T CARE DON'T CARE R/W 2/1 A5 A4 A3 A2 A1 A0 D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 DON'T CARE SDIO INSTRUCTION HEADER (REGISTER N) REGISTER (N) DATA REGISTER (N–1) DATA 03606-0-023 Figure 79. 2-Byte Serial Register Write in MSB First Mode t HI t t S H t LO t DS t CLK t DH SEN DON'T CARE SCLK DON'T CARE DON'T CARE SDIO DON'T CARE A0 A1 A2 A3 A4 A5 2/1 R/W D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7 INSTRUCTION HEADER (REGISTER N) REGISTER (N) DATA REGISTER (N+1) DATA 03606-0-024 Figure 80. 2-Byte Serial Register Write in LSB First Mode Rev. 0 | Page 43 of 52 AD9861 Read Operation can be configured by setting the SDIO BiDir register. In 3-wire The readback of registers can be a single or dual data byte mode, the SDIO pin becomes an output pin after receiving the operation. The readback can be configured to use 3-wire or 8-bit instruction header with a readback request. 4-wire and can be formatted with MSB first or LSB first. The instruction header is written to the device either MSB or LSB Figure 81 shows a 4-wire SPI read with MSB first; Figure 82 first (depending on the mode) followed by the 8-bit output data shows a 3-wire read with MSB first; and Figure 83 shows a (appropriately MSB or LSB justified). By default, the output data 4-wire read with LSB first. is sent to the dedicated output pin (SDO). Three-wire operation t t t S HI t CLK H t DS t t LO DV t DH SEN DON'T CARE SCLK DON'T CARE SDIO DON'T CARE R/W 2/1 A5 A4 A3 A2 A1 A0 DON'T CARE INSTRUCTION HEADER SDO DON'T CARE D7 D6 D5 D4 D3 D2 D1 D0 DON'T CARE OUTPUT REGISTER DATA 03606-0-025 Figure 81. 1-Byte Serial Register Readback In MSB First Mode, SDIO BiDir Bit Set Logic Low (Default, 4-Wire Mode) t t HI t t S CLK H t DS t t DV LO t DH SEN SCLK DON'T CARE DON'T CARE SDIO DON'T CARE R/W 2/1 A5 A4 A3 A2 A1 A0 D7 D6 D5 D4 D3 D2 D1 D0 DON'T CARE INSTRUCTION HEADER OUTPUT REGISTER DATA 03606-0-026 Figure 82. 1-Byte Serial Register Readback in MSB First Mode, SDIO BiDir Bit Set Logic High (Default, 3-Wire Mode) t t t S HI t CLK H t DS t t LO DV t DH SEN DON'T CARE DON'T CARE SCLK SDIO DON'T CARE A0 A1 A2 A3 A4 A5 2/1 R/W DON'T CARE INSTRUCTION HEADER SDO DON'T CARE D0 D1 D2 D3 D4 D5 D6 D7 DON'T CARE OUTPUT REGISTER DATA 03606-0-027 Figure 83. 1-Byte Serial Register Readback in LSB First Mode, SDIO BiDir Bit Set Logic Low (Default, 4-Wire Mode) Rev. 0 | Page 44 of 52 AD9861 Table 21. PLL Input and Output Minimum and Maximum CLOCK DISTRIBUTION BLOCK Clock Rates Theory/Description Input Clock Output Clock The AD9861 uses a clock distribution block to distribute the PLL Setting (Min/Max) (MHz) (Min/Max) (MHz) timing derived from the input clock (applied to the CLKIN pin, 1× (PLL Bypassed) 1/200 1/200 referred to here as CLKIN) to the Rx and Tx paths. There are 1× (PLL Enabled) 32/200 32/200 many options for configuring the clock distribution block, 2× 16/100 32/200 which are available through internal register settings. The Clock 4× 16/50 64/200 Distribution Block Diagram section describes the timing block 8× 16/25 128/200 diagram breakdown, followed by the data timing for the * 1/5 × 32/200 6.4/40 different data interface options. * 2/5 × 16/175 6.4/70 * 4/5 × 16/87.5 12.8/70 The clock distribution block contains a PLL, which includes an * 8/5 × 16/43.75 25.6/70 optional output divide-by-5 circuit, an ADC divide-by-2 circuit, * 16/5 × 16/21.875 51.2/70 multiplexers, and other digital logic. * Indicates PLL output divide-by-5 circuit enabled. There are two main methods of configuring the Rx path timing Clock Distribution Block Diagram of the AD9861, normal timing mode and alternative timing The Clock Distribution Block diagram is shown in mode, which are controlled through register Alt timing mode [Register 0x15, Bit 4]. In normal timing mode, the Rx path clock Figure 84. An output clock formatter configures the output is driven directly from the CLKIN input and the Tx path is synchronization signals, IFACE1, IFACE2, and IFACE3. These driven by a clock derived from CLKIN multiplied by the on interface pin signals depend on clock mode setting, data I/O chip PLL. In alternative timing mode, the input clock is applied configuration, and other operational settings. Clock mode and to the PLL circuitry, and the PLL output clock drives both the data I/O configuration are defined in register settings of Rx path clock and Tx path clock. clk_mode, SpiFDnHD, and SpiB10n20. Because alternative timing mode uses the PLL to derive the Rx Table 22 shows the configuration of the IFACE1, IFACE2 and path clock, the ADC performance may degrade slightly. This IFACE3 pins relative to clock mode (for half-duplex cases, the degradation is due to the phase noise from the PLL. Typically it IFACE1 pin is an input that identifies if the device is in Rx or Tx occurs in undersampling applications when the input signal is operation mode). The clock mode is used to specify the timing above the first Nyquist zone of the ADC. for each data interface operation modes, which are discussed in detail in the Flexible I/O Interface Options section. The T and R The PLL can provide 1×, 2×, 4×, 8×, and 16× multiplication or extensions after the half-duplex Modes 4, 5, 7, 8, and 10 in the can be bypassed and powered down through register PLL Table 22 indicate that the device is in transmit or receive bypass [Register 0x15, Bit 7] and through register PLL power- operation mode. The default clock mode setting [Register 0x01, down [Register 0x2, Bit 2]. The PLL requires a minimum input Bits 5–7, clk_mode] of ‘000’ configures clock Mode 1 for the clock frequency of 16 MHz and needs to provide a minimum full-duplex operation, Mode 4 for half-duplex 20 operation and PLL output clock of 32 MHz. This limit applies to the PLL Mode 7 for half-duplex 10 operation. Modes 2, 5, 8, and 10 are output prior to the optional divide-by-5 circuitry. For clock optional timing configurations for the AD9861 that can be frequencies below these limits, the PLL must be bypassed. The programmed through Register 0x01 clk_mode. PLL maximum output frequency before the divide-by-5 cir- cuitry is 350 MHz. Table 21 shows the input and output clock rates for all the multiplication settings. Rev. 0 | Page 45 of 52 AD9861 80MHz MAX 1, 2 CLKIN Rx PATH Rx DIGITAL BLOCK 4 IFACE2 1 OUTPUT CLOCK 1, 2, 4, 8, 16 FORMATTER 1, 5 IFACE3 Tx PATH Tx DIGITAL 3 BLOCK 5 6 2 1. ALTERNATE TIMING MODE: REG 0x15, BIT 4 2. PLL MULTIPLICATION SETTING: REG 0x15, BITS 2–0 3. PLL OUTPUT DIVIDE BY 5; REG 0x15, BIT 3 4. Rx PATH DIVIDE BY 2: REG 0x15, BIT 5 5. PLL BYPASS PATH: REG 0x15, BIT 7 6. INTERP CONTROL, Tx/Rx INV IFACE3, CLK MODE, INV IFACE2, FD/HD, 10/20 Figure 84. Clock Distribution Block Diagram Table 22. Interface Pins (IFACE1, IFACE2, IFACE3) Configuration Definition for Flexible Interface Operation Clock 1 2 4T 4R 5T 5R 7T 7R 8T 8R 10T 10R Mode PIN Full-Duplex Half-Duplex, 20-Bit Half-Duplex, 10-Bit Clone Mode IFACE1 TxSync Rx Rx Rx Tx/ Tx/ Tx/ IFACE2 Buff_CLKIN RxSync Optional CLKOUT Optional CLKOUT Optional CLKOUT IFACE3 Tx Clock Tx Rx Tx Rx Tx Rx Tx Rx Tx Rx Clock Clock Clock Clock Clock Clock Clock Clock Clock Clock The Tx clock output frequency depends on whether the data is An optional CLKOUT from IFACE2 is available as a stable in interleaved or parallel (noninterleaved) configuration. Modes system clock running at the CLKIN frequency or the TxDAC 1, 2, 7, 8, and 10 use Tx interleaved data and require either 2× or update rate, which is equal to CLKIN × PLL setting. Setting the 4× interpolation to be enabled. enable IFACE2 register [Register 0x01, Bit 2] enables the IFACE2 optional clock output. In FD mode, the IFACE2 pin • DAC update rate = CLKIN × PLL setting. always acts as a clock output; the enable IFACE2 pin can be used to invert the IFACE2 output. • Noninterleaved Tx data clock frequency = CLKIN × PLL Configuration setting × 1/(interpolation rate). The AD9861 timing for the transmit path and for the receive • Interleaved Tx data clock frequency = 2 × CLKIN × PLL path depend on the mode setting and various programmable setting × 1/(interpolation rate). options. The registers that affect the output clock timing and data input/output timing are clk_mode [2:0]; enable IFACE2; The Rx clock does not depend on whether the data is inter- inv clkout (IFACE3); Tx inverse sample; interpolation control; leaved or parallel, but does depend on the configuration of the PLL bypass; ADC clock div; Alt timing mode; PLL Div5; PLL timing mode: normal or alternative. multiplication; and PLL to IFACE2. The clk_mode register is • Normal timing mode, Rx clock frequency = CLKIN × ADC discussed previously. Table 23 shows the other register bits that Div factor (if enabled). are used to configure the output clock timing and data latching options available in the AD9861. • Alternative timing mode, Rx clock frequency = CLKIN × PLL setting × ADC Div factor (if enabled). Rev. 0 | Page 46 of 52 03606-0-067 AD9861 Table 23. Serial Registers Related to the Clock Distribution Block Register Address, Register Name Bit(s) Function Enable IFACE2 Register 0x01, Bit 2 0: There is no clock output from IFACE2 pin, except in FD mode. 1: The IFACE2 pin outputs a continuous reference clock from the PLL output. In FD mode, this inverts the IFACE2 output. Inv clkout (IFACE3) Register 0x01, Bit 1 0: The IFACE3 clock output is not inverted. 1: The IFACE3 clock output is inverted. Tx Inverse Sample Register 0x13, Bit 5 0: The Tx path data is latched relative to the output Tx clock rising edge. 1: The Tx path data is latched relative to the output Tx clock falling edge. Interpolation Control Register 0x13, Bit 1:0 Sets interpolation of 1×, 2×, or 4× for the Tx path. PLL Bypass Register 0x15, Bit 7 0: The PLL block is used to generate system clock. 1: The PLL block is bypassed to generate system clock. ADC Clock Div Register 0x15, Bit 5 0: ADC clock rate equals the Rx path frequency. 1: ADC clock is one-half the Rx path frequency. Alt Timing Mode Register 0x15, Bit 4 0: CLKIN is used to drive the Rx path clock. 1: PLL block output is used to drive the Rx path clock. PLL Div5 Register 0x15, Bit 3 0: PLL block output clock is not divided down. 1: PLL block output clock is divided by 5. PLL Multiplier Register 0x15, Bit 2:0 Sets multiplication factor of the PLL block to 1× (000), 2× (001), 4× (010), 8× (011), or 16x (100). PLL to IFACE2 Register 0x16, Bit 5 0: If enable IFACE2 register is set, IFACE2 outputs buffered CLKIN. 1: If enable IFACE2 register is set, IFACE2 outputs buffered PLL output clock. Table 24. AD9861 Typical Tx Data Latch Timing Relative to Transmit (Tx) timing requires specific setup and hold times to IFACE3 Falling Edge properly latch data through the data interface bus. These timing Mode No. Mode Name t (ns) t (ns) setup hold parameters are specified relative to an internally generated 1 FD 5 –2.5 output reference clock. The AD9861 has two interface clocks 2 Optional FD 5 –2.5 provided through the IFACE3 and IFACE2 pins. The transmit 4 HD20 5 –1.5 timing specifications, setup and hold time, provide a minimum required window of valid data. 5 Optional HD20 5 –1.5 7 HD10 5 –2.5 Setup time (tSETUP) is the time required for data to initially settle 8 Optional HD10 5 –2.5 to a valid logic level prior to the relative output timing edge. 10 Clone 5 –1.5 Hold time (t ) is the time after the output timing edge that HOLD valid data must remain on the data bus to be properly latched. Figure 85 shows t and t relative to IFACE3 falling edge. SETUP HOLD Receive (Rx) path data is output after a reference output clock Note that in some cases negative time is specified, for example edge. The time delay of the Rx data relative to a reference output with tHOLD timing, which means that the hold time edge occurs clock is called the output delay, tOD. The AD9861 has two before the relative output clock edge. possible interface clocks provided through the IFACE3 and t SETUP IFACE2 pins. Figure 86 shows tOD relative to IFACE3 rising t HOLD edge. Note that in some cases negative time is specified, which means that the output data transition occurs prior to the relative IFACE3 (CLKOUT) output clock edge. Tx DATA t OD 03606-0-028 IFACE3 (CLKOUT) Figure 85. Tx Data Timing Diagram Rx DATA Table 24 shows typical setup-and-hold times for the AD9861 in 03606-0-029 the various mode configurations. Figure 86. Rx Data Timing Diagram Rev. 0 | Page 47 of 52 AD9861 Table 25 shows typical output delay times for the AD9861 in the various mode configurations. Table 25. AD9861 Rx Data Latch Timing Mode No. Mode Name t Data Delay [ns] Relative to: OD 1 FD +2.5 ns Relative to IFACE2 rising edge +1 ns Relative to IFACE3 rising edge 2 Optional FD +1 ns Relative To IFACE3 rising edge +2 ns IFACE2 (RxSYNC) relative to LSB 4 HD20 −1.5 ns Relative to IFACE3 rising edge 5 Optional HD20 −0.5 ns Relative to IFACE3 rising edge 7 HD10 −1.5 ns Relative to IFACE3 rising edge 8 Optional HD10 +0.5 ns Relative to IFACE3 rising edge +0 ns U12 (RxSYNC) relative to LSB 10 Clone +1.5 ns Relative to IFACE3 rising edge Configuration without Serial Port Interface (Using Mode Pins) The AD9861 can be configured using mode pins if a serial port interface is not available. This section applies only to configuring the AD9861 without an SPI. Refer is the Digital Block, Configuring with Mode Pins section for further information. When using the mode pin option, the pins shown in Table 26 are used to configured the AD9861. Table 26. Using Mode Pin (SPI Disabled) to Configure Timing (SPI_CS, Pin 64, Must Be Tied Low) Interpolation HD 20 Interp1,Interp0 FD/ 10/ Clock Mode Setting PLL Setting Pin 1, Pin 2 Pin 3 Pin 17 1 Mode 1 (FD) 2× 2× 1 N/A 0, 1 4× 4× 1, 0 Mode 4 (HD20) 1× Bypassed 0 0 0, 0 2× 2× 0, 1 4× 4× 1, 0 Mode 7 (HD10) 2× 2× 0 1 0, 1 4× 4× 1, 0 1 Pin 17 (IFACE2) is an output clock in FD mode. Rev. 0 | Page 48 of 52 AD9861 OUTLINE DIMENSIONS 0.30 9.00 0.25 0.60 MAX BSC SQ 0.18 0.60 MAX PIN 1 INDICATOR 49 64 1 48 PIN 1 INDICATOR 7.25 TOP 8.75 BOTTOM VIEW 7.10 SQ* BSC SQ VIEW 6.95 0.45 0.40 33 16 17 32 0.35 0.25 MIN 7.50 REF 0.80 MAX 1.00 12° MAX  0.65 TYP 0.85 0.05 MAX 0.80 0.02 NOM 0.50 BSC 0.20 REF SEATING PLANE * COMPLIANT TO JEDEC STANDARDS MO-220-VMMD EXCEPT FOR EXPOSED PAD DIMENSION Figure 87. 64-Lead Lead Frame Chip Scale Package (LFCSP) [CP-64] Rev. 0 | Page 49 of 52 AD9861 ORDERING GUIDE Model Temperature Range Package Description Package Option AD9861BCP-50 64-Lead LFCSP CP-64 –40°C to +85°C (Ambient) AD9861BCP-80 64-Lead LFCSP CP-64 –40°C to +85°C (Ambient) AD9861BCPRL-50 64-Lead LFCSP CP-64 –40°C to +85°C (Ambient) AD9861BCPRL-80 64-Lead LFCSP CP-64 –40°C to +85°C (Ambient) AD9861-50EB 25°C (Ambient) Evaluation Board AD9861-80EB 25°C (Ambient) Evaluation Board Rev. 0 | Page 50 of 52 AD9861 NOTES Rev. 0 | Page 51 of 52 AD9861 NOTES © 2003 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. C03606–0–11/03(0) Rev. 0 | Page 52 of 52

Frequently asked questions

What makes Elite.Parts unique?

chervon down
At GID Industrial (Elite.Parts' parent company), we specialize in procuring industrial parts. We know where to find the rare and obsolete equipment that our customers need in order to get back to business. There are other companies who claim to do what we do, but we're confident that our commitment to quality and value is unparalleled in our field.

What kind of warranty will the AD9861-80 have?

chervon down
Warranties differ by part and by which suppliers we use to procure it for you. Sometimes, a part will be sold as-is and without a warranty. Our specialty, single board computers, tend to receive a one-year warranty.

Which carriers does Elite.Parts work with?

chervon down
Elite.Parts can ship via FedEx, UPS, DHL, and USPS. We have accounts with each of them and generally ship using one of those, but we can also ship using your account if you would prefer. However, we can use other carriers if it will be more convenient for you.

Will Elite.Parts sell to me even though I live outside the USA?

chervon down
Absolutely! We are happy to serve customers regardless of location. We work with international clients all the time, and we are familiar with shipping to destinations all across the globe.

I have a preferred payment method. Will Elite.Parts accept it?

chervon down
All major credit cards are accepted: Visa, MasterCard, Discover, and American Express. We will also accept payment made with wire transfer or PayPal. Checks will only be accepted from customers in the USA. Terms may available for larger orders, upon approval.

Why buy from GID?

quality

Quality

We are industry veterans who take pride in our work

protection

Protection

Avoid the dangers of risky trading in the gray market

access

Access

Our network of suppliers is ready and at your disposal

savings

Savings

Maintain legacy systems to prevent costly downtime

speed

Speed

Time is of the essence, and we are respectful of yours

What they say about us

FANTASTIC RESOURCE

star star star star star

One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!

Bucher Emhart Glass

EXCELLENT SERVICE

star star star star star

With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.

Fuji

HARD TO FIND A BETTER PROVIDER

star star star star star

Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.

Applied Materials

CONSISTENTLY DELIVERS QUALITY SOLUTIONS

star star star star star

Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.

Nidec Vamco

TERRIFIC RESOURCE

star star star star star

This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.

Trican Well Service

GO TO SOURCE

star star star star star

When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.

ConAgra Foods

Related Products

ANALOG DEVICE# A5E1032

SOCKET FOR MODEL AD210 IC

TRANSFORMER CURRENT 60.0 AMP

SOCKET FOR MODEL 1B22 IC

product

Analog Devices AD7291 12-Bit Low power 8-Channel Successive Approximation Analog-to-Digital Converte...