ANALOG DEVICES AD9230-11
Description
Analog Devices AD9230-11 11-Bit Monolithic Sampling Analog-to-Digital Converter
Part Number
AD9230-11
Price
Request Quote
Manufacturer
ANALOG DEVICES
Lead Time
Request Quote
Category
PRODUCTS - A
Specifications
# Chan
1
ADC Architecture
Pipelined
Ain Range
1.25 V p-p
Analog Input Type
Diff-Uni
Interface
LVDS,Par
Pkg Type
CSP
Resolution (Bits)
11bit
Sample Rate
200MSPS
Features
- 1.8 V analog and digital supply operation
- 700 MHz full power analog bandwidth
- Clock duty cycle stabilizer
- ENOB of 10.2 @ fIN up to 70 MHz @ 200 MSPS (-1.0 dBFS)
- Excellent linearity DNL = ±0.15 LSB typical INL = ±0.5 LSB typical
- Integrated data capture clock
- Integrated input buffer and track-and-hold amplifier
- Low power dissipation-373 mW @ 200 MSPS (LVDS SDR mode); 328 mW @ 200 MSPS (LVDS DDR mode)
- LVDS at 200 MSPS (ANSI-644 levels)
- On-chip reference, no external decoupling required
- Programmable input voltage range-1.0 V to 1.5 V, 1.25 V nominal
- Selectable output data format (offset binary, twos complement, gray code)
- SFDR = -77 dBc @ fIN up to 70 MHz @ 200 MSPS (-1.0 dBFS)
- SNR = 62.5 dBFS @ fIN up to 70 MHz @ 200 MSPS
Datasheet
Extracted Text
11-Bit, 200 MSPS, 1.8 V Analog-to-Digital Converter AD9230-11 FEATURES FUNCTIONAL BLOCK DIAGRAM RBIAS PWDN AGND AVDD SNR = 62.5 dBFS @ f up to 70 MHz @ 200 MSPS IN ENOB of 10.2 @ f up to 70 MHz @ 200 MSPS (−1.0 dBFS) IN REFERENCE AD9230-11 SFDR = −77 dBc @ f up to 70 MHz @ 200 MSPS (−1.0 dBFS) IN CML DRVDD Excellent linearity DRGND VIN+ DNL = ±0.15 LSB typical TRACK-AND-HOLD VIN– INL = ±0.5 LSB typical ADC 12 OUTPUT 11 12-BIT STAGING D10 TO D0 LVDS at 200 MSPS (ANSI-644 levels) CORE LVDS 700 MHz full power analog bandwidth CLK+ CLOCK OR+ MANAGEMENT CLK– OR– On-chip reference, no external decoupling required Integrated input buffer and track-and-hold amplifier SERIAL PORT DCO+ Low power dissipation DCO– 373 mW @ 200 MSPS (LVDS SDR mode) RESET SCLK SDIO CSB 328 mW @ 200 MSPS (LVDS DDR mode) Figure 1. Programmable input voltage range 1.0 V to 1.5 V, 1.25 V nominal 1.8 V analog and digital supply operation Selectable output data format (offset binary, twos complement, gray code) Clock duty cycle stabilizer Integrated data capture clock APPLICATIONS Wireless and wired broadband communications Cable reverse path Communications test equipment Radar and satellite subsystems Power amplifier linearization GENERAL DESCRIPTION PRODUCT HIGHLIGHTS The AD9230-11 is an 11-bit monolithic sampling analog-to- 1. High Performance. Maintains 62.5 dBFS SNR digital converter (ADC) optimized for high performance, @ 200 MSPS with a 70 MHz input. low power, and ease of use. The product operates at up to a 2. Low Power. Consumes only 373 mW @ 200 MSPS. 200 MSPS conversion rate and is optimized for outstanding 3. Ease of Use. LVDS output data and output clock signal dynamic performance in wideband carrier and broadband allow interface to current FPGA technology. The on-chip systems. All necessary functions, including a track-and-hold reference and sample-and-hold provide flexibility in (T/H) amplifier and voltage reference, are included on the system design. Use of a single 1.8 V supply simplifies chip to provide a complete signal conversion solution. system power supply design. 4. Serial Port Control. Standard serial port interface (SPI) The ADC requires a 1.8 V analog voltage supply and a supports various product functions, such as data formatting, differential clock for full performance operation. The digital disabling the clock duty cycle stabilizer, power-down, gain outputs are LVDS (ANSI-644) compatible and support twos adjust, and output test pattern generation. complement, offset binary format, or Gray code. A data clock 5. Pin-Compatible Family. 10-bit and 12-bit pin-compatible output is available for proper output data timing. family offered as AD9211 and AD9230. Fabricated on an advanced CMOS process, the AD9230-11 is available in a 56-lead lead frame chip scale package, specified over the industrial temperature range (−40°C to +85°C). Rev. 0 Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. rights of third parties that may result from its use. Specifications subject to change without notice. No Tel: 781.329.4700 www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Fax: 781.461.3113 ©2008 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. 07101-001 AD9230-11 TABLE OF CONTENTS Features .............................................................................................. 1 Theory of Operation ...................................................................... 16 Applications ....................................................................................... 1 Analog Input and Voltage Reference ....................................... 16 Functional Block Diagram .............................................................. 1 Clock Input Considerations ...................................................... 17 General Description ......................................................................... 1 Power Dissipation and Power-Down Mode ........................... 18 Product Highlights ........................................................................... 1 Digital Outputs ........................................................................... 18 Revision History ............................................................................... 2 Timing ......................................................................................... 19 Specif ica t ions ..................................................................................... 3 RBIAS ........................................................................................... 19 DC Specifications ......................................................................... 3 Configuration Using the SPI ..................................................... 19 AC Specifications .......................................................................... 4 Hardware Interface ..................................................................... 20 Digital Specifications ................................................................... 5 Configuration Without the SPI ................................................ 20 Switching Specifications .............................................................. 6 Memory Map .................................................................................. 22 Timing Diagrams .......................................................................... 7 Reading the Memory Map Table .............................................. 22 Absolute Maximum Ratings ............................................................ 8 Reserved Locations .................................................................... 22 Thermal Resistance ...................................................................... 8 Default Values ............................................................................. 22 ESD Caution .................................................................................. 8 Logic Levels ................................................................................. 22 Pin Configurations and Function Descriptions ........................... 9 Transfer Register Map ................................................................ 22 Typical Performance Characteristics ........................................... 13 Outline Dimensions ....................................................................... 25 Equivalent Circuits ......................................................................... 15 Ordering Guide .......................................................................... 25 REVISION HISTORY 10/08—Revision 0: Initial Version Rev. 0 | Page 2 of 28 AD9230-11 SPECIFICATIONS DC SPECIFICATIONS AVDD = 1.8 V, DRVDD = 1.8 V, T = −40°C, T = +85°C, f = −1.0 dBFS, full scale = 1.25 V, DCS enabled, unless otherwise noted. MIN MAX IN Table 1. 1 Parameter Temp Min Typ Max Unit RESOLUTION 11 Bits ACCURACY No Missing Codes Full Guaranteed Offset Error 25°C 4.2 mV Full −12 +12 mV Gain Error 25°C 0.89 % FS Full −2.2 +4.3 % FS Differential Nonlinearity (DNL) 25°C ±0.15 LSB Full −0.4 +0.4 LSB Integral Nonlinearity (INL) 25°C ±0.5 LSB Full −0.5 +0.5 LSB TEMPERATURE DRIFT Offset Error Full ±9 μV/°C Gain Error Full 0.019 %/°C ANALOG INPUTS (VIN+, VIN−) 2 Differential Input Voltage Range Full 0.98 1.25 1.5 V p-p Input Common-Mode Voltage Full 1.4 V Input Resistance (Differential) Full 4.3 kΩ Input Capacitance 25°C 2 pF POWER SUPPLY AVDD Full 1.7 1.8 1.9 V DRVDD Full 1.7 1.8 1.9 V Supply Currents 3 IAVDD Full 152 164 mA 3 4 I /SDR Mode Full 55 58 mA DRVDD 3 5 I /DDR Mode Full 36 mA DRVDD 3 Power Dissipation Full 4 SDR Mode Full 373 400 mW 5 DDR Mode Full 338 mW 1 See the AN-835 Application Note, Understanding High Speed ADC Testing and Evaluation, for a complete set of definitions and an explanation of how these tests were completed. 2 The input range is programmable through the SPI, and the range specified reflects the nominal values of each setting. See the Memory Map section. 3 I and I are measured with a −1 dBFS, 10.3 MHz sine input at rated sample rate. AVDD DRVDD 4 Single data rate mode; this is the default mode of the AD9230-11. 5 Double data rate mode; user-programmable feature. See the Memory Map section. Rev. 0 | Page 3 of 28 AD9230-11 AC SPECIFICATIONS 1 AVDD = 1.8 V, DRVDD = 1.8 V, TMIN = −40°C, TMAX = +85°C, fIN = −1.0 dBFS, full scale = 1.25 V, DCS enabled, unless otherwise noted. Table 2. 2 Parameter Temp Min Typ Max Unit SNR fIN = 10 MHz 25°C 62.4 62.9 dB Full 62.2 dB fIN = 70 MHz 25°C 62.2 62.5 dB Full 62.0 dB f = 170 MHz 25°C 61.8 dB IN SINAD f = 10 MHz 25°C 62.3 62.8 dB IN Full 62.1 dB fIN = 70 MHz 25°C 62.0 62.3 dB Full 61.8 dB fIN = 170 MHz 25°C 61.5 dB EFFECTIVE NUMBER OF BITS (ENOB) fIN = 10 MHz 25°C 10.3 Bits fIN = 70 MHz 25°C 10.2 Bits f = 170 MHz 25°C 10.1 Bits IN WORST HARMONIC (SECOND OR THIRD) fIN = 10 MHz 25°C −86 −77 dBc Full −77 dBc f = 70 MHz 25°C −79 −77 dBc IN Full −76 dBc fIN = 170 MHz 25°C −76 dBc WORST OTHER (SFDR EXCLUDING SECOND AND THIRD) fIN = 10 MHz 25°C −88 −84 dBc Full −79 dBc fIN = 70 MHz 25°C −84 −82 dBc Full −81 dBc f = 170 MHz 25°C −82 dBc IN ANALOG INPUT BANDWIDTH 25°C 700 MHz 1 All ac specifications tested by driving CLK+ and CLK− differentially. 2 See the AN-835 Application Note, Understanding High Speed ADC Testing and Evaluation, for a complete set of definitions and an explanation of how these tests were completed. Rev. 0 | Page 4 of 28 AD9230-11 DIGITAL SPECIFICATIONS AVDD = 1.8 V, DRVDD = 1.8 V, TMIN = −40°C, TMAX = +85°C, fIN = −1.0 dBFS, full scale = 1.25 V, DCS enabled, unless otherwise noted. Table 3. 1 Parameter Temp Min Typ Max Unit CLOCK INPUTS Logic Compliance Full CMOS/LVDS/LVPECL Internal Common-Mode Bias Full 1.2 V Differential Input Voltage Full 0.2 6 V p-p Input Voltage Range Full AGND − 0.3 AVDD + 1.6 V Input Common-Mode Range Full 1.1 AVDD V High Level Input Voltage (VIH) Full 1.2 3.6 V Low Level Input Voltage (VIL) Full 0 0.8 V High Level Input Current (IIH) Full −10 +10 μA Low Level Input Current (I) Full −10 +10 μA IL Input Resistance (Differential) Full 16 20 24 kΩ Input Capacitance Full 4 pF LOGIC INPUTS Logic 1 Voltage Full 0.8 × AVDD V Logic 0 Voltage Full 0.2 × AVDD V Logic 1 Input Current (SDIO) Full 0 μA Logic 0 Input Current (SDIO) Full −60 μA Logic 1 Input Current (SCLK, PWDN, CSB, RESET) Full 55 μA Logic 0 Input Current (SCLK, PWDN, CSB, RESET) Full 0 μA Input Capacitance 25°C 4 pF 2 LOGIC OUTPUTS V Differential Output Voltage Full 247 454 mV OD V Output Offset Voltage Full 1.125 1.375 V OS Output Coding Twos complement, gray code, or offset binary (default) 1 See the AN-835 Application Note, Understanding High Speed ADC Testing and Evaluation, for a complete set of definitions and an explanation of how these tests were completed. 2 LVDS R = 100 Ω. TERMINATION Rev. 0 | Page 5 of 28 AD9230-11 SWITCHING SPECIFICATIONS AVDD = 1.8 V, DRVDD = 1.8 V, TMIN = −40°C, TMAX = +85°C, fIN = −1.0 dBFS, full scale = 1.25 V, DCS enabled, unless otherwise noted. Table 4. Parameter Temp Min Typ Max Unit CONVERSION RATE Maximum Conversion Rate Full 200 MSPS Minimum Conversion Rate Full 40 MSPS PULSE WIDTH CLK+ Pulse Width High (tCH) Full 2.25 2.5 ns CLK+ Pulse Width Low (t ) Full 2.25 2.5 ns CL 1 OUTPUT (LVDS, SDR MODE) Data Propagation Delay (tPD) Full 3.8 ns Rise Time (t ) (20% to 80%) 25°C 0.2 ns R Fall Time (t ) (20% to 80%) 25°C 0.2 ns F DCO Propagation Delay (tCPD) Full 3.9 ns Data to DCO Skew (tSKEW) Full −0.3 0.1 0.5 ns Latency Full 6 Cycles 2 OUTPUT (LVDS, DDR MODE) Data Propagation Delay (tPD) Full 3.8 ns Rise Time (tR) (20% to 80%) 25°C 0.2 ns Fall Time (t ) (20% to 80%) 25°C 0.2 ns F DCO Propagation Delay (t ) Full 3.9 ns CPD Data to DCO Skew (t ) Full −0.5 0.1 0.3 ns SKEW Latency Full 6 Cycles APERTURE UNCERTAINTY (JITTER, t ) 25°C 0.2 ps rms J 1 See Figure 2. 2 See Figure 3. Rev. 0 | Page 6 of 28 AD9230-11 TIMING DIAGRAMS N – 1 t N + 4 A N + 5 N N + 3 VIN N + 1 N + 2 t t 1/f CH CL S CLK+ CLK– t CPD DCO+ DCO– t SKEW t PD Dx+ N – 6 N – 5 N – 4 N – 3 N – 2 Dx– Figure 2. Single Data Rate Mode N – 1 t N + 4 A N + 5 N N + 3 VIN N + 1 N + 2 t t 1/f CH CL S CLK+ CLK– t CPD DCO+ DCO– t SKEW t PD D5+ D5 NO D5 NO D5 NO D5 NO D5 NO N – 7 DATA N – 6 DATA N – 5 DATA N – 4 DATA N – 3 DATA D5– D4/D10+ D10 D4 D10 D4 D10 D4 D10 D4 D10 D4 N – 7 N – 6 N – 6 N – 5 N – 5 N – 4 N – 4 N – 3 N – 3 N – 2 D4/D10– 6 MSBs 5 LSBs Figure 3. Double Data Rate Mode Rev. 0 | Page 7 of 28 07101-003 07101-002 AD9230-11 ABSOLUTE MAXIMUM RATINGS Stresses above those listed under Absolute Maximum Ratings Table 5. may cause permanent damage to the device. This is a stress Parameter Rating rating only; functional operation of the device at these or any Electrical other conditions above those indicated in the operational AVDD to AGND −0.3 V to +2.0 V section of this specification is not implied. Exposure to absolute DRVDD to DRGND −0.3 V to +2.0 V maximum rating conditions for extended periods may affect AGND to DRGND −0.3 V to +0.3 V device reliability. AVDD to DRVDD −2.0 V to +2.0 V THERMAL RESISTANCE D0+/D0− through D10+/D10− −0.3 V to DRVDD + 0.3 V to DRGND The exposed paddle must be soldered to the ground plane DCO+/DCO− to DRGND −0.3 V to DRVDD + 0.3 V for the LFCSP package. Soldering the exposed paddle to the OR+/OR− to DGND −0.3 V to DRVDD + 0.3 V customer board increases the reliability of the solder joints, CLK+ to AGND −0.3 V to +3.9 V maximizing the thermal capability of the package. CLK− to AGND −0.3 V to +3.9 V Table 6. VIN+ to AGND −0.3 V to AVDD + 0.2 V VIN− to AGND −0.3 V to AVDD + 0.2 V Package Type θJA θJC Unit SDIO/DCS to DGND −0.3 V to DRVDD + 0.3 V 56-Lead LFCSP (CP-56-2) 30.4 2.9 °C/W PWDN to AGND −0.3 V to +3.9 V Typical θJA and θJC are specified for a 4-layer board in still air. CSB to AGND −0.3 V to +3.9 V Airflow increases heat dissipation, effectively reducing θJA. In SCLK/DFS to AGND −0.3 V to +3.9 V addition, metal that is in direct contact with the package leads Environmental reduces the θ . JA Storage Temperature Range −65°C to +125°C ESD CAUTION Operating Temperature Range −40°C to +85°C Lead Temperature 300°C (Soldering, 10 sec) Junction Temperature 150°C Rev. 0 | Page 8 of 28 AD9230-11 PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS D2– 1 PIN 1 42 AVDD INDICATOR D2+ 2 41 AVDD D3– 3 40 CML D3+ 4 39 AVDD D4– 5 38 AVDD D4+ 6 37 AVDD AD9230-11 DRVDD 7 36 VIN– TOP VIEW DRGND 8 35 VIN+ (Not to Scale) D5– 9 34 AVDD 33 AVDD D5+ 10 D6– 11 32 AVDD D6+ 12 31 RBIAS D7– 13 30 AVDD D7+ 14 29 PWDN NOTES 1. DNC = DO NOT CONNECT. 2. PIN 0 (EXPOSED PADDLE) = AGND. Figure 4. Single Data Rate Mode Pin Configuration Table 7. Single Data Rate Mode Pin Function Descriptions Pin No. Mnemonic Description 30, 32 to 34, 37 to 39, 41 to AVDD 1.8 V Analog Supply. 43, 46 7, 24, 47 DRVDD 1.8 V Digital Output Supply. 1 0 AGND Analog Ground. The exposed paddle should be connected to the analog ground. 1 8, 23, 48 DRGND Digital Output Ground. 35 VIN+ Analog Input (True). 36 VIN− Analog Input (Complement). 40 CML Common-Mode Output Pin. Enabled through the SPI, this pin provides a reference for the optimized internal bias voltage for VIN+/VIN−. 44 CLK+ Clock Input (True). 45 CLK− Clock Input (Complement). 31 RBIAS Set Pin for Chip Bias Current. Place 1% 10 kΩ resistor terminated to ground. Nominally 0.5 V. 28 RESET CMOS-Compatible Chip Reset (Active Low). 25 SDIO/DCS Serial Port Interface (SPI) Data Input/Output (Serial Port Mode). Duty Cycle Stabilizer Select (External Pin Mode). 26 SCLK/DFS Serial Port Interface Clock (Serial Port Mode). Data Format Select Pin (External Pin Mode). 27 CSB Serial Port Chip Select (Active Low). 29 PWDN Chip Power-Down. 49 DCO− Data Clock Output (Complement). 50 DCO+ Data Clock Output Input (True). 51, 52 DNC Do No Connect. 53 D0− (LSB) D0 Complement Output Bit (LSB). 54 D0+ (LSB) D0 True Output Bit (LSB). 55 D1− D1 Complement Output Bit. 56 D1+ D1 True Output Bit. 1 D2− D2 Complement Output Bit. 2 D2+ D2 True Output Bit. Rev. 0 | Page 9 of 28 07101-004 D8– 15 56 D1+ D8+ 16 55 D1– D9– 17 54 D0+ (LSB) D9+ 18 53 D0– (LSB) (MSB) D10– 19 52 DNC (MSB) D10+ 20 51 DNC OR– 50 DCO+ 21 OR+ 22 49 DCO– DRGND 23 48 DRGND DRVDD 24 47 DRVDD SDIO/DCS 25 46 AVDD SCLK/DFS 26 45 CLK– CSB 27 44 CLK+ RESET 28 43 AVDD AD9230-11 Pin No. Mnemonic Description 3 D3− D3 Complement Output Bit. 4 D3+ D3 True Output Bit. 5 D4− D4 Complement Output Bit. 6 D4+ D4 True Output Bit. 9 D5− D5 Complement Output Bit. 10 D5+ D5 True Output Bit. 11 D6− D6 Complement Output Bit. 12 D6+ D6 True Output Bit. 13 D7− D7 Complement Output Bit. 14 D7+ D77 True Output Bit. 15 D8− D8 Complement Output Bit. 16 D8+ D8 True Output Bit. 17 D9− D9 Complement Output Bit. 18 D9+ D9 True Output Bit. 19 D10− (MSB) D10 Complement Output Bit (MSB). 20 D10+ (MSB) D10 True Output Bit (MSB). 21 OR− Overrange Complement Output Bit. 22 OR+ Overrange True Output Bit. 1 AGND and DRGND should be tied to a common quiet ground plane. Rev. 0 | Page 10 of 28 AD9230-11 D2/D8– 1 PIN 1 42 AVDD INDICATOR D2/D8+ 2 41 AVDD D3/D9– 3 40 CML D3/D9+ 4 39 AVDD (MSB) D4/D10– 5 38 AVDD (MSB) D4/D10+ 6 37 AVDD AD9230-11 DRVDD 7 36 VIN– TOP VIEW DRGND 8 35 VIN+ (Not to Scale) OR– 9 34 AVDD OR+ 10 33 AVDD DNC 11 32 AVDD DNC 12 31 RBIAS DNC 13 30 AVDD DNC 14 29 PWDN NOTES 1. DNC = DO NOT CONNECT. 2. PIN 0 (EXPOSED PADDLE) = AGND. Figure 5. Double Data Rate Mode Pin Configuration Table 8. Double Data Rate Mode Pin Function Descriptions Pin No. Mnemonic Description 30, 32 to 34, 37 to 39, AVDD 1.8 V Analog Supply. 41 to 43, 46 7, 24, 47 DRVDD 1.8 V Digital Output Supply. 1 0 AGND Analog Ground. The exposed paddle should be connected to the analog ground. 1 8, 23, 48 DRGND Digital Output Ground. 35 VIN+ Analog Input Input (True). 36 VIN− Analog Input (Complement). 40 CML Common-Mode Output Pin. Enabled through the SPI, this pin provides a reference for the optimized internal bias voltage for VIN+/VIN−. 44 CLK+ Clock Input Input (True). 45 CLK− Clock Input (Complement). 31 RBIAS Set Pin for Chip Bias Current. Place 1% 10 kΩ resistor terminated to ground. Nominally 0.5 V. 28 RESET CMOS-Compatible Chip Reset (Active Low). 25 SDIO/DCS Serial Port Interface (SPI) Data Input/Output (Serial Port Mode). Duty Cycle Stabilizer Select (External Pin Mode). 26 SCLK/DFS Serial Port Interface Clock (Serial Port Mode). Data Format Select Pin (External Pin Mode). 27 CSB Serial Port Chip Select (Active Low). 29 PWDN Chip Power-Down. 49 DCO− Data Clock Output (Complement). 50 DCO+ Data Clock Output Input (True). 51 ND/D5− ND/D5 Complement Output Bit. 52 ND/D5+ ND/D5 True Output Bit. 53 D0/D6− (LSB) D0/D6 Complement Output Bit (LSB). 54 D0/D6+ (LSB) D0/D6 True Output Bit (LSB). 55 D1/D7− D1/D7 Complement Output Bit. 56 D1/D7+ D1/D7 True Output Bit. 1 D2/D8− D2/D8 Complement Output Bit. 2 D2/D8+ D2/D8 True Output Bit. Rev. 0 | Page 11 of 28 07101-005 DNC 15 56 D1/D7+ DNC 16 55 D1/D7– DNC 17 54 D0/D6+ (LSB) DNC 18 53 D0/D6– (LSB) DNC 19 52 ND/D5+ DNC 20 51 ND/D5– DNC/(OR–) 21 50 DCO+ DNC/(OR+) 22 49 DCO– DRGND 23 48 DRGND DRVDD 24 47 DRVDD SDIO/DCS 25 46 AVDD SCLK/DFS 26 45 CLK– CSB 27 44 CLK+ RESET 28 43 AVDD AD9230-11 Pin No. Mnemonic Description 3 D3/D9− D3/D9 Complement Output Bit. 4 D3/D9+ D3/D9 True Output Bit. 5 D4/D10− (MSB) D4/D10 Complement Output Bit (MSB). 6 D4/D10+ (MSB) D4/D10 True Output Bit (MSB). 9 OR− OR Complement Output Bit. This pin is disabled if Pin 21 is reconfigured through the SPI to be OR−. 10 OR+ OR True Output Bit. This pin is disabled if Pin 22 is reconfigured through the SPI to be OR+. 11 to 20 DNC Do Not Connect. 21 DNC/(OR−) Do Not Connect. This pin can be reconfigured as the Overrange Complement Output Bit through the serial port register. 22 DNC/(OR+) Do Not Connect. This pin can be reconfigured as the Overrange True Output Bit through the serial port register. 1 AGND and DRGND should be tied to a common quiet ground plane. Rev. 0 | Page 12 of 28 AD9230-11 TYPICAL PERFORMANCE CHARACTERISTICS AVDD = 1.8 V, DRVDD = 1.8 V, rated sample rate, DCS enabled, TA = 25°C, 1.25 V p-p differential input, AIN = −1 dBFS, unless otherwise noted. 0 85 200MSPS 10.3MHz @ –1.0dBFS –20 SNR: 62.9dB 80 SNR (dB) +85°C ENOB: 10.3 BITS SFDR: 86dBc –40 75 –60 70 SFDR (dBc) +25°C SFDR (dBc) –40°C –80 65 SNR (dB) +25°C –100 60 SNR (dB) –40°C –120 55 –140 50 0 10 20 30 40 50 60 70 80 90 100 0 50 100 150 200 250 300 350 400 450 FREQUENCY (MHz) ANALOG INPUT FREQUENCY (MHz) Figure 6. 64k Point Single-Tone FFT; 200 MSPS, 10.3 MHz Figure 9. Single-Tone SNR/SFDR vs. Input Frequency (fIN) with 1.25 V p-p Full-Scale; 200 MSPS 0 100 200MSPS SFDR (dBFS) 70.3MHz @ –1.0dBFS 90 –20 SNR: 62.5dB ENOB: 10.2 BITS 80 SFDR: 77dBc –40 70 SNR (dBFS) 60 –60 50 –80 40 30 –100 SFDR (dBc) SNR (dB) 20 –120 10 –140 0 0 10 20 30 40 50 60 70 80 90 100 –90 –80 –70 –60 –50 –40 –30 –20 –10 0 FREQUENCY (MHz) AMPLITUDE (dBFS) Figure 7. 64k Point Single-Tone FFT; 200 MSPS, 70.3 MHz Figure 10. SNR/SFDR vs. Input Amplitude; 140.3 MHz 6.0 0 200MSPS 170.3MHz @ –1.0dBFS 5.5 –20 SNR: 61.3dB ENOB: 10.1 BITS SFDR: 73dBc 5.0 –40 4.5 –60 4.0 –80 3.5 –100 3.0 –120 2.5 –140 2.0 0 10 20 30 40 50 60 70 80 90 100 –40 –30 –20 –10 0 10 20 30 40 50 60 70 80 90 TEMPERATURE (°C) FREQUENCY (MHz) Figure 11. Offset vs. Temperature Figure 8. 64k Point Single-Tone FFT; 170 MSPS, 140.3 MHz Rev. 0 | Page 13 of 28 AMPLITUDE (dBFS) AMPLITUDE (dBFS) AMPLITUDE (dBFS) 07101-030 07101-029 07101-028 OFFSET (mV) SNR/SFDR (dB) SNR/SFDR (dB) 07101-012 07101-032 07101-031 AD9230-11 1.0 1.0 0.8 0.8 0.6 0.6 0.4 0.4 0.2 0.2 0 0 –0.2 –0.2 –0.4 –0.4 –0.6 –0.6 –0.8 –0.8 –1.0 –1.0 0 512 1024 1536 2048 0 512 1024 1536 2048 OUTPUT CODE OUTPUT CODE Figure 12. DNL Figure 14. INL 2.5 2.0 1.5 1.0 0.5 0 –0.5 –60 –40 –20 0 20 40 60 80 100 120 TEMPERATURE (°C) Figure 13. Gain vs. Temperature Rev. 0 | Page 14 of 28 GAIN (%FS) DNL (LSB) 07101-013 07101-034 INL (LSB) 07101-033 AD9230-11 EQUIVALENT CIRCUITS AVDD AVDD 25kΩ 1kΩ CSB 1.2V 10kΩ 10kΩ CLK+ CLK– Figure 15. Clock Inputs Figure 18. Equivalent CSB Input Circuit AVDD DRVDD AVDD VIN+ BUF 2kΩ V V+ V– CML BUF ~1.4V AVDD Dx– Dx+ 2kΩ V– V+ VIN– BUF Figure 16. Analog Inputs (V = ~1.4 V) Figure 19. LVDS Outputs (Dx+, Dx−, OR+, OR−, DCO+, DCO−) CML AVDD DRVDD 25kΩ SCLK/DFS 1kΩ RESET PWDN 1kΩ SDIO/DCS 25kΩ Figure 17. Equivalent SCLK/DFS, RESET, PWDN Input Circuit Figure 20. Equivalent SDIO/DCS Input Circuit Rev. 0 | Page 15 of 28 07101-008 07101-007 07101-006 07101-010 07101-009 07101-011 AD9230-11 THEORY OF OPERATION The AD9230-11 architecture consists of a front-end sample- Differential Input Configurations and-hold amplifier (SHA) followed by a pipelined switched Optimum performance is achieved while driving the AD9230-11 capacitor ADC. The quantized outputs from each stage are in a differential input configuration. For baseband applications, combined into a final 11-bit result in the digital correction the AD8138 differential driver provides excellent performance logic. The pipelined architecture permits the first stage to and a flexible interface to the ADC. The output common-mode operate on a new input sample, while the remaining stages operate voltage of the AD8138 is easily set to AVDD/2 + 0.5 V, and the on preceding samples. Sampling occurs on the rising edge of the driver can be configured in a Sallen-Key filter topology to clock. provide band limiting of the input signal. Each stage of the pipeline, excluding the last, consists of a low 1V p-p 49.9Ω resolution flash ADC connected to a switched capacitor DAC 499Ω AVDD and interstage residue amplifier (MDAC). The residue amplifier 33Ω 499Ω VIN+ magnifies the difference between the reconstructed DAC output AD8138 20pF AD9230-11 and the flash input for the next stage in the pipeline. One bit of 523Ω 0.1µF redundancy is used in each stage to facilitate digital correction VIN– 33Ω CML of flash errors. The last stage simply consists of a flash ADC. 499Ω The input stage contains a buffered differential SHA that can Figure 21. Differential Input Configuration Using the AD8138 be ac- or dc-coupled. The output staging block aligns the data, At input frequencies in the second Nyquist zone and above, the carries out the error correction, and passes the data to the out- performance of most amplifiers may not be adequate to achieve the put buffers. The output buffers are powered from a separate true performance of the AD9230-11. This is especially true in IF supply, allowing adjustment of the output voltage swing. During undersampling applications where frequencies in the 70 MHz to power-down, the output buffers go into a high impedance state. 100 MHz range are being sampled. For these applications, differen- ANALOG INPUT AND VOLTAGE REFERENCE tial transformer coupling is the recommended input configuration. The analog input to the AD9230-11 is a differential buffer. For The signal characteristics must be considered when selecting a best dynamic performance, the source impedances driving transformer. Most RF transformers saturate at frequencies below a VIN+ and VIN− should be matched such that common-mode few megahertz and excessive signal power can also cause core settling errors are symmetrical. The analog input is optimized saturation, leading to distortion. In any configuration, the value of to provide superior wideband performance and requires that the shunt capacitor, C, is dependent on the input frequency and the analog inputs be driven differentially. SNR and SINAD may need to be reduced or removed. performance degrades significantly if the analog input is driven 15Ω with a single-ended signal. VIN+ 1.25V p-p 50Ω A wideband transformer, such as Mini-Circuits® ADT1-1WT, can 2pF AD9230-11 provide the differential analog inputs for applications that require a VIN– 15Ω single-ended-to-differential conversion. Both analog inputs are self- 0.1µF biased by an on-chip resistor divider to a nominal 1.4 V. An internal differential voltage reference creates positive and negative Figure 22. Differential Transformer—Coupled Configuration reference voltages that define the 1.25 V p-p fixed span of the ADC As an alternative to using a transformer-coupled input at frequen- core. This internal voltage reference can be adjusted by means of cies in the second Nyquist zone, the AD8352 differential driver can SPI control. See the Configuration Using the SPI section. be used (see Figure 23). V CC 0.1µF 0.1µF 0Ω 16 8, 13 1 0.1µF ANALOG INPUT 11 R 2 VIN+ 200Ω C R R AD8352 C D D G AD9230-11 200Ω 3 0.1µF 10 R CML VIN– 4 ANALOG INPUT 5 14 0Ω 0.1µF 0.1µF 0.1µF Figure 23. Differential Input Configuration Using the AD8352 Rev. 0 | Page 16 of 28 07101-016 07101-015 07101-014 AD9230-11 In some applications, it is acceptable to drive the sample clock CLOCK INPUT CONSIDERATIONS inputs with a single-ended CMOS signal. In such applications, For optimum performance, the AD9230-11 sample clock inputs CLK+ should be directly driven from a CMOS gate, and the (CLK+ and CLK−) should be clocked with a differential signal. CLK− pin should be bypassed to ground with a 0.1 μF capacitor This signal is typically ac-coupled into the CLK+ pin and the in parallel with a 39 kΩ resistor (see Figure 27). Although the CLK− pin via a transformer or capacitors. These pins are biased CLK+ input circuit supply is AVDD (1.8 V), this input is internally and require no additional bias. designed to withstand input voltages up to 3.3 V (as shown in Figure 24 shows a preferred method for clocking the AD9230-11. Figure 28), making the selection of the drive logic voltage very The low jitter clock source is converted from single-ended to flexible. differential using an RF transformer. The back-to-back Schottky AD9510/AD9511/ diodes across the secondary transformer limit clock excursions AD9512/AD9513/ AD9514/AD9515 0.1µF into the AD9230-11 to approximately 0.8 V p-p differential. This CLOCK CLK INPUT OPTIONAL helps prevent the large voltage swings of the clock from feeding 0.1µF 100Ω 50Ω* CLK+ through to other portions of the AD9230-11 and preserves the CMOS DRIVER ADC fast rise and fall times of the signal, which are critical to low CLK AD9230-11 jitter performance. 0.1µF CLK– 0.1µF 39kΩ MINI-CIRCUITS ADT1–1WT, 1:1Z *50Ω RESISTOR IS OPTIONAL. 0.1µF 0.1µF XFMR CLOCK CLK+ Figure 27. Single-Ended 1.8 V CMOS Sample Clock INPUT 100Ω ADC 50Ω AD9230-11 0.1µF CLK– AD9510/AD9511/ 0.1µF SCHOTTKY AD9512/AD9513/ DIODES: AD9514/AD9515 HSM2812 0.1µF CLOCK CLK Figure 24. Transformer-Coupled Differential Clock INPUT OPTIONAL 0.1µF 50Ω* 100Ω CMOS DRIVER CLK+ If a low jitter clock is available, another option is to ac couple ADC a differential PECL signal to the sample clock input pins as CLK AD9230-11 0.1µF 0.1µF shown in Figure 25. The AD9510/AD9511/AD9512/AD9513/ CLK– AD9514/AD9515 family of clock drivers offers excellent jitter performance. *50Ω RESISTOR IS OPTIONAL. AD9510/AD9511/ Figure 28. Single-Ended 3.3 V CMOS Sample Clock AD9512/AD9513/ AD9514/AD9515 0.1µF Clock Duty Cycle Considerations 0.1µF CLOCK CLK CLK+ INPUT Typical high speed ADCs use both clock edges to generate a ADC 100Ω PECL DRIVER AD9230-11 variety of internal timing signals. As a result, these ADCs may 0.1µF 0.1µF CLOCK CLK– be sensitive to clock duty cycle. Commonly, a 5% tolerance is CLK INPUT 240Ω 240Ω 50Ω* 50Ω* required on the clock duty cycle to maintain dynamic performance characteristics. The AD9230-11 contains a duty cycle stabilizer *50Ω RESISTORS ARE OPTIONAL. (DCS) that retimes the nonsampling edge, providing an internal Figure 25. Differential PECL Sample Clock clock signal with a nominal 50% duty cycle. This allows a wide range of clock input duty cycles without affecting the perform- ance of the AD9230-11. When the DCS is on, noise and distortion AD9510/AD9511/ AD9512/AD9513/ performance are nearly flat for a wide range of duty cycles. AD9514/AD9515 0.1µF 0.1µF However, some applications may require the DCS function to CLOCK CLK CLK+ INPUT be off. If so, keep in mind that the dynamic range performance can ADC 100Ω be affected when operated in this mode. See the Configuration LVDS DRIVER AD9230-11 0.1µF 0.1µF CLOCK Using the SPI section for more details on using this feature. CLK– CLK INPUT 50Ω* 50Ω* The duty cycle stabilizer uses a delay-locked loop (DLL) to create the nonsampling edge. As a result, any changes to the *50Ω RESISTORS ARE OPTIONAL. sampling frequency require approximately eight clock cycles Figure 26. Differential LVDS Sample Clock to allow the DLL to acquire and lock to the new rate. Rev. 0 | Page 17 of 28 07101-017 07101-018 07101-019 07101-020 07101-021 AD9230-11 Clock Jitter Considerations DIGITAL OUTPUTS High speed, high resolution ADCs are sensitive to the quality of the Digital Outputs and Timing clock input. The degradation in SNR at a given input frequency The AD9230-11 differential outputs conform to the ANSI-644 (fA) due only to aperture jitter (tJ) can be calculated by LVDS standard on default power-up. This can be changed to a low power, reduced signal option similar to the IEEE 1596.3 SNR Degradation = 20 × log10[1/2 × π × fA × tJ] standard using the SPI. This LVDS standard can further reduce In this equation, the rms aperture jitter represents the root mean the overall power dissipation of the device, which reduces the square of all jitter sources, including the clock input, analog input power by ~39 mW. See the Memory Map section for more signal, and ADC aperture jitter specifications. IF undersampling information. The LVDS driver current is derived on-chip and applications are particularly sensitive to jitter (see Figure 29). sets the output current at each output equal to a nominal Treat the clock as an analog signal in cases where aperture jitter 3.5 mA. A 100 Ω differential termination resistor placed at the may affect the dynamic range of the AD9230-11. Power supplies LVDS receiver inputs results in a nominal 350 mV swing at the for clock drivers should be separated from the ADC output receiver. driver supplies to avoid modulating the clock signal with digital The AD9230-11 LVDS outputs facilitate interfacing with LVDS noise. Low jitter, crystal-controlled oscillators make the best receivers in custom ASICs and FPGAs that have LVDS capability clock sources. If the clock is generated from another type of for superior switching performance in noisy environments. source (by gating, dividing, or other methods), it should be Single point-to-point net topologies are recommended with a retimed by the original clock at the last step. 100 Ω termination resistor placed as close to the receiver as Refer to the AN-501 Application Note and the AN-756 possible. No far-end receiver termination and poor differential Application Note for more in-depth information about jitter trace routing may result in timing errors. It is recommended performance as it relates to ADCs (visit www.analog.com). that the trace length is no longer than 24 inches and that the 130 differential output traces are kept close together and at equal RMS CLOCK JITTER REQUIREMENT 120 lengths. 110 An example of the LVDS output using the ANSI standard (default) 16 BITS 100 data eye and a time interval error (TIE) jitter histogram with trace lengths less than 24 inches on regular FR-4 material is 90 14 BITS shown in Figure 30. Figure 31 shows an example of when the 80 12 BITS trace lengths exceed 24 inches on regular FR-4 material. Notice 70 that the TIE jitter histogram reflects the decrease of the data eye 10 BITS 60 opening as the edge deviates from the ideal position. It is up to 0.125ps 8 BITS 0.25ps 50 the user to determine if the waveforms meet the timing budget 0.5ps of the design when the trace lengths exceed 24 inches. 40 1.0ps 2.0ps 14 30 1 10 100 1000 500 ANALOG INPUT FREQUENCY (MHz) 12 400 Figure 29. Ideal SNR vs. Input Frequency and Jitter 300 10 POWER DISSIPATION AND POWER-DOWN MODE 200 100 8 The power dissipated by the AD9230-11 is proportional to its 0 sample rate. The digital power dissipation does not vary much 6 –100 because it is determined primarily by the DRVDD supply and –200 bias current of the LVDS output drivers. 4 –300 By asserting PWDN (Pin 29) high, the AD9230-11 is placed in –400 2 standby mode or full power-down mode, as determined by the –500 contents of Register 0x08. Reasserting the PWDN pin low 0 –3 –2 –1 0123 –40 –20 0 20 40 returns the AD9230-11 to its normal operational mode. TIME (ns) TIME (ps) An additional standby mode is supported by means of varying Figure 30. Data Eye for LVDS Outputs in ANSI Mode with Trace Lengths Less the clock input. When the clock rate falls below 20 MHz, the than 24 Inches on Standard FR-4 AD9230-11 assumes a standby state. In this case, the biasing network and internal reference remain on, but digital circuitry is powered down. Upon reactivating the clock, the AD9230-11 resumes normal operation after allowing for the pipeline latency. Rev. 0 | Page 18 of 28 SNR (dB) 07101-022 VOLTAGE (mV) TIE JITTER HISTOGRAM (Hits) 07101-023 AD9230-11 +FS – 1 LSB 600 12 OR DATA OUTPUTS 1 1111 1111 OR 0 1111 1111 400 10 0 1111 1111 –FS + 1/2 LSB 200 8 0 0000 0000 0 0000 0000 1 0000 0000 0 6 –FS +FS –FS – 1/2 LSB +FS – 1/2 LSB –200 4 Figure 32. OR Relation to Input Voltage and Output Data –400 2 TIMING The AD9230-11 provides latched data outputs with a pipeline –600 0 delay of seven clock cycles. Data outputs are available one –3 –2 –1 0123 –100 0 100 propagation delay (t ) after the rising edge of the clock signal. TIME (ns) TIME (ps) PD Figure 31. Data Eye for LVDS Outputs in ANSI Mode with Trace Lengths The length of the output data lines and loads placed on them Greater than 24 Inches on Standard FR-4 should be minimized to reduce transients within the AD9230-11. The format of the output data is offset binary by default. An These transients can degrade the dynamic performance of the example of the output coding format can be found in Table 12. converter. The AD9230-11 also provides data clock output (DCO) If it is desired to change the output data format to twos comple- intended for capturing the data in an external register. The data ment, see the Configuration Using the SPI section. outputs are valid on the rising edge of DCO. An output clock signal is provided to assist in capturing data The lowest typical conversion rate of the AD9230-11 is 40 MSPS. from the AD9230-11. The DCO is used to clock the output At clock rates below 1 MSPS, the AD9230-11 assumes the data and is equal to the sampling clock (CLK) rate. In single standby mode. data rate mode (SDR), data is clocked out of the AD9230-11 RBIAS and must be captured on the rising edge of the DCO. In double The AD9230-11 requires the user to place a 10 kΩ resistor data rate mode (DDR), data is clocked out of the AD9230-11 between the RBIAS pin and ground. This resister should have and must be captured on the rising and falling edges of the a 1% tolerance and is used to set the master current reference DCO See the timing diagrams shown in Figure 2 and Figure 3 of the ADC core. for more information. CONFIGURATION USING THE SPI Output Data Rate and Pinout Configuration The output data of the AD9230-11 can be configured to drive The AD9230-11 SPI allows the user to configure the converter for 12 pairs of LVDS outputs at the same rate as the input clock specific functions or operations through a structured register space signal (single data rate, or SDR, mode), or six pairs of LVDS inside the ADC. This gives the user added flexibility to customize device operation depending on the application. Addresses are outputs at 2× the rate of the input clock signal (double data rate, accessed (programmed or readback) serially in 1-byte words. Each or DDR, mode). SDR is the default mode; the device can be byte may be further divided down into fields, which are reconfigured for DDR by setting Bit 3 in Register 14 (see Table 13). documented in the Memory Map section. Out-of-Range (OR) There are three pins that define the serial port interface (SPI) to this An out-of-range condition exists when the analog input voltage particular ADC. They are the SCLK/DFS, SDIO/DCS, and CSB is beyond the input range of the ADC. OR is a digital output pins. The SCLK/DFS (serial clock) is used to synchronize the read that is updated along with the data output corresponding to the and write data presented to the ADC. The SDIO/DCS (serial data particular sampled input voltage. Thus, OR has the same input/output) is a dual-purpose pin that allows data to be sent and pipeline latency as the digital data. OR is low when the analog read from the internal ADC memory map registers. The CSB pin is input voltage is within the analog input range and high when an active low control that enables or disables the read and write the analog input voltage exceeds the input range, as shown in cycles (see Table 9). Figure 32. OR remains high until the analog input returns to within the input range and another conversion is completed. By logically AND-ing OR with the MSB and its complement, over- range high or underrange low conditions can be detected. Rev. 0 | Page 19 of 28 VOLTAGE (mV) TIE JITTER HISTOGRAM (Hits) 07101-024 07101-025 AD9230-11 HARDWARE INTERFACE Table 9. Serial Port Interface Pins Mnemonic Function The pins described in Table 9 comprise the physical interface between the user’s programming device and the serial port SCLK SCLK (serial clock) is the serial shift clock in. SCLK is used to synchronize serial interface of the AD9230-11. All serial pins are inputs, which is an open- reads and writes. drain output and should be tied to an external pull-up or SDIO SDIO (serial data input/output) is a dual-purpose pull-down resistor (suggested value of 10 kΩ). pin. The typical role for this pin is an input and This interface is flexible enough to be controlled by either PROMS output depending on the instruction being sent and the relative position in the timing frame. or PIC microcontrollers as well. This provides the user with an CSB CSB (chip select bar) is an active low control that alternate method to program the ADC other than using an SPI gates the read and write cycles. controller. RESET Master Device Reset. When asserted, device If the user chooses not to use the SPI interface, some pins serve assumes default settings. Active low. a dual function and are associated with a specific function when strapped externally to AVDD or ground during device power The falling edge of CSB, in conjunction with the rising edge of on. The Configuration Without the SPI section describes the the SCLK, determines the start of the framing. An example of strappable functions supported on the AD9230-11. the serial timing and its definitions can be found in Figure 33 and Table 11. CONFIGURATION WITHOUT THE SPI During an instruction phase, a 16-bit instruction is transmitted. In applications that do not interface to the SPI control registers, Data then follows the instruction phase and is determined by the SDIO/DCS and SCLK/DFS pins can alternately serve as the W0 and W1 bits, which is 1 or more bytes of data. All data is standalone CMOS-compatible control pins. When the device is composed of 8-bit words. The first bit of each individual byte of powered up, it is assumed that the user intends to use the pins serial data indicates whether this is a read or write command. as static control lines for the duty cycle stabilizer. In this mode, This allows the serial data input/output (SDIO) pin to change the CSB pin should be connected to AVDD, which disables the direction from an input to an output. serial port interface. Data can be sent in MSB or in LSB first mode. MSB first is Table 10. Mode Selection default on power-up and can be changed by changing the Mnemonic External Voltage Configuration configuration register. For more information about this feature SDIO/DCS AVDD Duty cycle stabilizer enabled and others, see the AN-877 Application Note, Interfacing to AGND Duty cycle stabilizer disabled High Speed ADCs via SPI, at www.analog.com. SCLK/DFS AVDD Twos complement enabled AGND Offset binary enabled t t DS HI t t CLK H t t S DH t LO CSB SCLK DON’T CARE DON’T CARE D5 D4 D3 D2 D1 D0 DON’T CARE SDIO DON’T CARE R/W W1 W0 A12 A11 A10 A9 A8 A7 Figure 33. Serial Port Interface Timing Diagram Rev. 0 | Page 20 of 28 07101-027 AD9230-11 Table 11. Serial Timing Definitions Parameter Timing (minimum, ns) Description tDS 5 Setup time between the data and the rising edge of SCLK tDH 2 Hold time between the data and the rising edge of SCLK t 40 Period of the clock CLK t 5 Setup time between CSB and SCLK S t 2 Hold time between CSB and SCLK H tHI 16 Minimum period that SCLK should be in a logic high state tLO 16 Minimum period that SCLK should be in a logic low state tEN_SDIO 1 Minimum time for the SDIO pin to switch from an input to an output relative to the SCLK falling edge (not shown in Figure 33) t 5 Minimum time for the SDIO pin to switch from an output to an input relative to the SCLK DIS_SDIO rising edge (not shown in Figure 33) Table 12. Output Data Format Offset Binary Output Mode Twos Complement Mode Input (V) Condition (V) D10 to D0 D10 to D0 OR VIN+ − VIN− < 0.62 0000 0000 000 1000 0000 000 1 VIN+ − VIN− = 0.62 0000 0000 000 1000 0000 000 0 VIN+ − VIN− = 0 0000 0000 000 0000 0000 000 0 VIN+ − VIN− = 0.62 1111 1111 111 0111 1111 111 0 VIN+ − VIN− > 0.62 + 0.5 LSB 1111 1111 111 0111 1111 111 1 Rev. 0 | Page 21 of 28 AD9230-11 MEMORY MAP READING THE MEMORY MAP TABLE RESERVED LOCATIONS Each row in the memory map table has eight address locations. Undefined memory locations should not be written to other The memory map is roughly divided into three sections: chip than their default values suggested in this data sheet. Addresses configuration register map (Address 0x00 to Address 0x02), that have values marked as 0 should be considered reserved and have a 0 written into their registers during power-up. transfer register map (Address 0xFF), and ADC functions map (Address 0x08 to Address 0x2A). DEFAULT VALUES The Addr. (Hex) column of the memory map indicates the Coming out of reset, critical registers are preloaded with default register address in hexadecimal, and the Default Value (Hex) values. These values are indicated in Table 13. Other registers column shows the default hexadecimal value that is already do not have default values and retain the previous value when written into the register. The Bit 7 (MSB) column is the start of exiting reset. the default hexadecimal value given. For example, Hexadecimal LOGIC LEVELS Address 0x09, the clock register, has a hexadecimal default value of 0x01. This means Bit 7 = 0, Bit 6 = 0, Bit 5 = 0, Bit 4 = 0, Bit 3 = 0, An explanation of logic level terminology follows: “bit is set” is Bit 2 = 0, Bit 1 = 0, and Bit 0 = 1, or 0000 0001 in binary. The synonymous with “bit is set to Logic 1” or “writing Logic 1 for default value enables the duty cycle stabilizer. Overwriting this the bit.” Similarly, “clear a bit” is synonymous with “bit is set to default so that Bit 0 = 0 disables the duty cycle stabilizer. For more Logic 0” or “writing Logic 0 for the bit.” information on this and other functions, consult the AN-877 TRANSFER REGISTER MAP Application Note, Interfacing to High Speed ADCs via SPI, at Address 0x08 to Address 0x18 are shadowed. Writes to these www.analog.com. addresses do not affect part operation until a transfer command is issued by writing 0x01 to Address 0xFF, setting the transfer bit. This allows these registers to be updated internally and simultaneously when the transfer bit is set. The internal update takes place when the transfer bit is set, and the bit autoclears. Table 13. Memory Map Register Default Addr. Bit 7 Bit 0 Value Notes/ (Hex) Register Name (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 (LSB) (Hex) Comments Chip Configuration Registers 0x00 chip_port_config 0 LSB Soft 1 1 Soft LSB first 0 0x18 The nibbles should first reset reset be mirrored by the user so that LSB-or MSB-first mode registers correctly, regardless of shift mode. 0x01 chip_id 8-bit chip ID, Bits[7:0] Read- Default is unique AD9230-11 = 0x0C only chip ID, different for each device. This is a read-only register. 0x02 chip_grade 0 0 0 Speed grade: X X X Read- Child ID used to only differentiate 11 = 200 MSPS graded devices. Transfer Register 0xFF device_update 0 0 0 0 0 0 0 SW 0x00 Synchronously transfer transfers data from the master shift register to the slave. Rev. 0 | Page 22 of 28 AD9230-11 Default Addr. Bit 7 Bit 0 Value Notes/ (Hex) Register Name (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 (LSB) (Hex) Comments ADC Functions 0x08 modes 0 0 PWDN: 0 0 Internal power-down mode: 0x00 Determines various generic modes of 0 = full 000 = normal (power-up, default) chip operation. (default) 001 = full power-down 1 = 010 = standby standby 011 = normal (power-up) Note: external PWDN pin overrides this setting 0x09 clock 0 0 0 0 0 0 0 Duty 0x01 cycle stabilizer: 0 = disabled 1 = enabled (default) 0x0D test_io 0 0 Reset Reset Output test mode: 0x00 When this register PN23 PN9 gen: is set, the test data 0000 = off (default) gen: 1 = on is placed on the 0001 = midscale short output pins in 1 = on 0 = off 0010 = +FS short 0 = off (default) place of normal 0011 = −FS short (default) data. 0100 = checker board output 0101 = PN 23 sequence 0110 = PN 9 0111 = one/zero word toggle 1000 = unused 1001 = unused 1010 = unused 1011 = unused 1100 = unused (Format determined by output_mode) 0x0F ain_config 0 0 0 0 0 Analog CML 0 0x00 input enable: disable: 1 = on 1 = on 0 = off 0 = off (default) (default) 0x14 output_mode 0 0 0 Output DDR: Output Data format select: 0x00 enable: 1 = invert: 00 = offset binary 1 = on (default) 0 = enabled 01 = twos 0 = 0 = off enable disabled (default) complement (default) (default) 10 = gray code 1 = disable 0x15 output_adjust 0 0 0 0 LVDS LVDS fine adjust: 0x00 course 001 = 3.50 mA adjust: 010 = 3.25 mA 0 = 011 = 3.00 mA 3.5 mA 100 = 2.75 mA (default) 101 = 2.50 mA 1 = 110 = 2.25 mA 2.0 mA 111 = 2.00 mA 16 output_phase Output 0 0 0 0 0 0 0x03 clock polarity 1 = inverted 0 = normal (default) Rev. 0 | Page 23 of 28 AD9230-11 Default Addr. Bit 7 Bit 0 Value Notes/ (Hex) Register Name (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 (LSB) (Hex) Comments 0x17 flex_output_delay Output 0 0 Output clock delay: 0 delay 00000 = 0.1 ns enable: 00001 = 0.2 ns 0 = 00010 = 0.3 ns enable … 1 = 11101 = 3.0 ns disable 11110 = 3.1 ns 11111 = 3.2 ns 0x18 flex_vref 0 0 0 Input voltage range setting: 0 10000 = 0.98 V 10001 =1.00 V 10010 = 1.02 V 10011 =1.04 V … 11111 = 1.23 V 00000 = 1.25 V 00001 = 1.27 V … 01110 = 1.48 V 01111 = 1.50 V 0x2A ovr_config 0 0 0 0 0 0 OR OR 0x01 position enable: (DDR 1 = on mode (default) only): 0 = off 0 = Pin 9, Pin 10 1 = Pin 21, Pin 22 Rev. 0 | Page 24 of 28 AD9230-11 OUTLINE DIMENSIONS 0.30 8.00 0.23 0.60 MAX BSC SQ 0.18 0.60 MAX PIN 1 43 56 INDICATOR 1 42 PIN 1 INDICATOR TOP 4.45 EXPOSED 7.75 VIEW PAD 4.30 SQ BSC SQ (BOTTOM VIEW) 4.15 0.50 14 0.40 29 28 15 0.30 0.30 MIN 6.50 REF 0.80 MAX 1.00 12° MAX 0.65 TYP 0.85 0.05 MAX FOR PROPER CONNECTION OF 0.80 THE EXPOSED PAD, REFER TO 0.02 NOM THE PIN CONFIGURATION AND COPLANARITY SEATING 0.50 BSC FUNCTION DESCRIPTIONS 0.08 0.20 REF PLANE SECTION OF THIS DATA SHEET. COMPLIANT TO JEDEC STANDARDS MO-220-VLLD-2 Figure 34. 56-Lead Lead Frame Chip Scale Package [LFCSP_VQ] 8 mm × 8 mm Body, Very Thin Quad (CP-56-2) Dimensions shown in millimeters ORDERING GUIDE Model Temperature Range Package Description Package Option 1 AD9230BCPZ11-200 −40°C to +85°C 56-Lead Lead Frame Chip Scale Package [LFCSP_VQ] CP-56-2 1 AD923011-200EBZ LVDS Evaluation Board 1 Z = RoHS Compliant Part. Rev. 0 | Page 25 of 28 100808-A AD9230-11 NOTES Rev. 0 | Page 26 of 28 AD9230-11 NOTES Rev. 0 | Page 27 of 28 AD9230-11 NOTES ©2008 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D07101-0-10/08(0) Rev. 0 | Page 28 of 28
Frequently asked questions
What makes Elite.Parts unique?
What kind of warranty will the AD9230-11 have?
Which carriers does Elite.Parts work with?
Will Elite.Parts sell to me even though I live outside the USA?
I have a preferred payment method. Will Elite.Parts accept it?
Why buy from GID?
Quality
We are industry veterans who take pride in our work
Protection
Avoid the dangers of risky trading in the gray market
Access
Our network of suppliers is ready and at your disposal
Savings
Maintain legacy systems to prevent costly downtime
Speed
Time is of the essence, and we are respectful of yours
Manufacturers


What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods