ANALOG DEVICES AD8694

Low Cost, Low Noise, CMOS, RRO Operational Amplifiers AD8691/AD8692/AD8694 FEATURES PIN CONFIGURATIONS Offset voltage: 400 μV typical OUT 1 5 V+ Low offset voltage drift: 6 μV/°C maximum AD8691 V– 2 TOP VIEW (AD8692/AD8694) (Not to Scale) Very low input bias currents: 1 pA maximum 3 +IN 4 –IN Low noise: 8 nV/√Hz Figure 1. 5-Lead TSOT Low distortion: 0.0006% Wide bandwidth: 10 MHz AD8691 OUT A 1 5 V+ Unity-gain stable Single-supply operation: 2.7 V to 6 V V– 2 Qualified for automotive applications +IN A 3 4 –IN APPLICATIONS Figure 2. 5-Lead SC70 Photodiode amplification OUT A 1 8 V+ Battery-powered instrumentation AD8692 –IN A 2 7 OUT B Medical instruments TOP VIEW +IN A 3 6 –IN B (Not to Scale) Multipole filters V– 4 5 +IN B Sensors Figure 3. 8-Lead MSOP Portable audio devices OUT A 1 8 V+ GENERAL DESCRIPTION AD8692 –IN A 2 7 OUT B The AD8691, AD8692, and AD8694 are low cost, single, dual, +IN A 3 6 –IN B TOP VIEW (Not to Scale) V– 4 5 +IN B and quad rail-to-rail output, single-supply amplifiers featuring low offset and input voltages, low current noise, and wide signal Figure 4. 8-Lead SOIC bandwidth. The combination of low offset, low noise, very low OUT A 1 14 OUT D input bias currents, and high speed make these amplifiers useful –IN A 2 13 –IN D in a wide variety of applications. Filters, integrators, photodiode +IN A 3 12 +IN D AD8694 amplifiers, and high impedance sensors all benefit from this V+ 4 TOP VIEW 11 V– (Not to Scale) combination of performance features. Audio and other ac +IN B 5 10 +IN C applications benefit from the wide bandwidth and low –IN B 6 9 –IN C OUT B 7 8 OUT C distortion of these devices. Applications for these amplifiers include power amplifier (PA) Figure 5. 14-Lead SOIC controls, laser diode control loops, portable and loop-powered OUT A 1 14 OUT D instrumentation, audio amplification for portable devices, and 2 13 –IN A –IN D ASIC input and output amplifiers. +IN A 3 12 +IN D AD8694 The small SC70 and TSOT package options for the AD8691 TOP VIEW V+ 4 11 V– (Not to Scale) allow it to be placed next to sensors, thereby reducing external +IN B 5 10 +IN C noise pickup. –IN B 6 9 –IN C 7 8 OUT B OUT C The AD8691, AD8692, and AD8694 are specified over the extended industrial temperature range of −40°C to +125°C. Figure 6. 14-Lead TSSOP The AD8691 single is available in 5-lead SC70 and 5-lead TSOT packages. The AD8692 dual is available in 8-lead MSOP and narrow SOIC surface-mount packages. The AD8694 quad is available in 14-lead TSSOP and narrow 14-lead SOIC packages. See the Ordering Guide section for automotive grades. Rev. E Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. rights of third parties that may result from its use. Specifications subject to change without notice. No Tel: 781.329.4700 www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Fax: 781.461.3113 ©2004–2011 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. 04991-030 04991-031 04991-002 04991-032 04991-001 04991-033 AD8691/AD8692/AD8694 TABLE OF CONTENTS Features .............................................................................................. 1 Absolute Maximum Ratings ............................................................5 Applications....................................................................................... 1 Thermal Characteristics ...............................................................5 General Description ......................................................................... 1 ESD Caution...................................................................................5 Pin Configurations ........................................................................... 1 Typical Performance Characteristics ..............................................6 Revision History ............................................................................... 2 Outline Dimensions....................................................................... 11 Specifications..................................................................................... 3 Ordering Guide .......................................................................... 14 Electrical Characteristics............................................................. 3 Automotive Products................................................................. 14 REVISION HISTORY 8/11—Rev. D to Rev. E 3/05—Rev. A to Rev. B Changes to Figure 20........................................................................ 8 Added AD8694 ...................................................................Universal 11/10—Rev. C to Rev. D 1/05—Rev. 0 to Rev. A Changes to Features Section and General Descriptions Added AD8691 ...................................................................Universal Section................................................................................................ 1 Changes to Features ..........................................................................1 Updated Outline Dimensions ....................................................... 11 Added Figure 1 and Figure 2............................................................1 Changes to Ordering Guide .......................................................... 14 Changes to Electrical Characteristics .............................................3 Added Automotive Products Section .......................................... 14 Changes to Figure 6 caption.............................................................6 Changes to Figure 9...........................................................................6 5/07—Rev. B to Rev. C Updated Outline Dimensions....................................................... 11 Change to Figure 1 ........................................................................... 1 Changes to Ordering Guide .......................................................... 11 Changes to Large Signal Voltage Gain Values in Table 1 ............ 3 Change to Phase Margin Symbol in Table 1 ................................. 3 10/04—Revision 0: Initial Version Change to TA Value for Table 2....................................................... 4 Changes to Large Signal Voltage Gain Values in Table 2 ............ 4 Change to Phase Margin Symbol in Table 2 ................................. 4 Changes to Table 4............................................................................ 5 Changes to Outline Dimensions................................................... 11 Changes to Ordering Guide .......................................................... 12 Rev. E | Page 2 of 16 AD8691/AD8692/AD8694 SPECIFICATIONS ELECTRICAL CHARACTERISTICS V = 2.7 V, V = V /2, T = 25°C, unless otherwise noted. S CM S A Table 1. Parameter Symbol Conditions Min Typ Max Unit INPUT CHARACTERISTICS Offset Voltage VOS VCM = −0.3 V to +1.6 V 0.4 2.0 mV V = −0.1 V to +1.6 V; −40°C < T < +125°C 3.0 mV CM A Input Bias Current I 0.2 1 pA B −40°C < TA < +85°C 50 pA −40°C < TA < +125°C 260 pA Input Offset Current IOS 0.1 0.5 pA −40°C < T < +85°C 20 pA A −40°C < T < +125°C 75 pA A Input Voltage Range −0.3 +1.6 V Common-Mode Rejection Ratio CMRR VCM = −0.3 V to +1.6 V 68 90 dB VCM = −0.1 V to +1.6 V; −40°C < TA < +125°C 60 85 dB Large Signal Voltage Gain AVO AD8691/AD8692 R = 2 kΩ, V = 0.5 V to 2.2 V 90 250 V/mV L O AD8694 R = 2 kΩ, V = 0.5 V to 2.2 V 60 V/mV L O Offset Voltage Drift ∆VOS/∆T AD8691 2 12 μV/°C AD8692/AD8694 1.3 6 μV/°C INPUT CAPACITANCE Common-Mode Input Capacitance CCM 5 pF Differential Input Capacitance CDM 2.5 pF OUTPUT CHARACTERISTICS Output Voltage High VOH IL = 1 mA 2.64 2.66 V −40°C < TA < +125°C 2.6 V Output Voltage Low V I = 1 mA 25 40 mV OL L −40°C < T < +125°C 60 mV A Short-Circuit Current ISC ±20 mA Closed-Loop Output Impedance ZOUT f = 1 MHz, AV = 1 12 Ω POWER SUPPLY Power Supply Rejection Ratio PSRR VS = 2.7 V to 5.5 V 80 95 dB −40°C < TA < +125°C 75 95 dB Supply Current/Amplifier ISY VO = 0 V 0.85 0.95 mA −40°C < T < +125°C 1.2 mA A DYNAMIC PERFORMANCE Slew Rate SR RL = 2 kΩ 5 V/μs Settling Time t To 0.01% 1 μs S Gain Bandwidth Product GBP 10 MHz Phase Margin Ø 60 Degrees m Total Harmonic Distortion + Noise THD + N G = 1, RL = 600 Ω, f = 1 kHz, VO = 250 mV p-p 0.003 % NOISE PERFORMANCE Voltage Noise e f = 0.1 Hz to 10 Hz 1.6 3.0 μV p-p n p-p Voltage Noise Density en f = 1 kHz 8 12 nV/√Hz en f = 10 kHz 6.5 nV/√Hz Current Noise Density i f = 1 kHz 0.05 pA/√Hz n Rev. E | Page 3 of 16 AD8691/AD8692/AD8694 V = 5.0 V, V = V /2, T = 25°C, unless otherwise noted. S CM S A Table 2. Parameter Symbol Conditions Min Typ Max Unit INPUT CHARACTERISTICS Offset Voltage V V = −0.3 V to +3.9 V 0.4 2.0 mV OS CM V = −0.1 V to +3.9 V; −40°C < T < +125°C 3.0 mV CM A Input Bias Current I 0.2 1 pA B −40°C < TA < +85°C 50 pA −40°C < TA < +125°C 260 pA Input Offset Current IOS 0.1 0.5 pA −40°C < T < +85°C 20 pA A −40°C < T < +125°C 75 pA A Input Voltage Range −0.3 +3.9 V Common-Mode Rejection Ratio CMRR VCM = −0.3 V to +3.9 V 70 95 dB VCM = −0.1 V to +3.9 V; −40°C < TA < +125°C 67 95 dB Large Signal Voltage Gain AVO AD8691/AD8692 V = 0.5 V to 4.5 V, R = 2 kΩ, V = 0 V 250 2000 V/mV O L CM AD8694 V = 0.5 V to 4.5 V, R = 2 kΩ, V = 0 V 150 V/mV O L CM Offset Voltage Drift ∆VOS/∆T AD8691 2 12 μV/°C AD8692/AD8694 1.3 6 μV/°C INPUT CAPACITANCE Common-Mode Input Capacitance CCM 5 pF Differential Input Capacitance CDM 2.5 pF OUTPUT CHARACTERISTICS Output Voltage High VOH IL = 1 mA 4.96 4.98 V IL = 10 mA 4.7 4.78 V −40°C to +125°C 4.6 V Output Voltage Low V I = 1 mA 20 40 mV OL L AD8691/AD8692 IL = 10 mA 165 210 mV AD8694 IL = 10 mA 185 240 mV AD8691/AD8692 −40°C to +125°C 290 mV AD8694 −40°C to +125°C 370 mV Short-Circuit Current I ±80 mA SC Closed-Loop Output Impedance Z f = 1 MHz, A = 1 10 Ω OUT V POWER SUPPLY Power Supply Rejection Ratio PSRR V = 2.7 V to 5.5 V 80 95 dB S −40°C < T < +125°C 75 95 dB A Supply Current/Amplifier ISY VO = 0 V 0.95 1.05 mA −40°C < TA < +125°C 1.3 mA DYNAMIC PERFORMANCE Slew Rate SR RL = 2 kΩ 5 V/μs Settling Time tS To 0.01% 1 μs Full Power Bandwidth BWP <1% distortion 360 kHz Gain Bandwidth Product GBP 10 MHz Phase Margin Ø 65 Degrees m Total Harmonic Distortion + Noise THD + N G = 1, RL = 600 Ω, f = 1 kHz, VO = 1 V p-p 0.0006 % NOISE PERFORMANCE Voltage Noise e f = 0.1 Hz to 10 Hz 1.6 3.0 μV p-p n p-p Voltage Noise Density en f = 1 kHz 8 12 nV/√Hz en f = 10 kHz 6.5 nV/√Hz Current Noise Density in f = 1 kHz 0.05 pA/√Hz Rev. E | Page 4 of 16 AD8691/AD8692/AD8694 ABSOLUTE MAXIMUM RATINGS T = 25°C, unless otherwise noted. A THERMAL CHARACTERISTICS θ is specified for the worst-case conditions, that is, the device JA Table 3. soldered in the circuit board for surface-mount packages. Parameter Rating Supply Voltage 6 V Table 4. Thermal Resistance Input Voltage V − 0.3 V to V + 0.3 V SS DD Package Type θ θ Unit JA JC Differential Input Voltage ±6 V 8-Lead MSOP (RM-8) 210 45 °C/W Output Short-Circuit Duration Observe derating curves 8-Lead SOIC (R-8) 158 43 °C/W to GND 5-Lead TSOT (UJ-5) 207 61 °C/W Storage Temperature Range −65°C to +150°C 5-Lead SC70 (KS-5) 376 126 °C/W Operating Temperature Range −40°C to +125°C 14-Lead TSSOP (RU-14) 180 35 °C/W Junction Temperature Range −65°C to +150°C 14-Lead SOIC (R-14) 120 36 °C/W Lead Temperature 300°C (Soldering, 60 sec) ESD CAUTION Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Rev. E | Page 5 of 16 AD8691/AD8692/AD8694 TYPICAL PERFORMANCE CHARACTERISTICS VS = +5 V or ±2.5 V, unless otherwise noted. 2500 300 V = 5V V = 5V AND 2.7V S S V = –0.3V TO +3.9V CM 250 2000 200 1500 150 100 1000 50 500 0 0 –50 –40 –30 –20 –10 0 10 20 30 40 50 60 70 80 90 100 110 120 –2.0 –1.5 –1.0 –0.5 0 0.5 1.0 1.5 2.0 V (mV) TEMPERATURE (°C) OS Figure 7. Input Offset Voltage Distribution Figure 10. Input Bias Current vs. Temperature 1.0 30 V = 5V AND 2.7V S V = 2.5V CM 25 T = –40°C TO +125°C A 0.8 20 0.6 15 0.4 10 0.2 5 0 0 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 7.0 7.5 8.0 0 1 2 345 6 7 T V (µV/°C) V (V) C OS S Figure 8. AD8692/AD8694 Input Offset Voltage Drift Distribution Figure 11. Supply Current vs. Supply Voltage 2.5 2000 V = ±2.5V AND ±1.35V V = 5V S S 1600 I @ ±2.5V T = 25°C SY A 1200 2.0 I @ ±1.35V SY 800 1.5 400 0 1.0 –400 –800 0.5 –1200 –1600 0 –2000 –40 –20 0 20 40 60 80 100 120 140 –0.3 0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3.0 3.3 3.6 3.9 TEMPERATURE (°C) COMMON-MODE VOLTAGE (V) Figure 9. Input Offset Voltage vs. Common-Mode Voltage Figure 12. Supply Current vs. Temperature Rev. E | Page 6 of 16 INPUT OFFSET VOLTAGE (µV) NUMBER OF AMPLIFIERS NUMBER OF AMPLIFIERS 04991-004 04991-003 04991-005 SUPPLY CURRENT (mA) I (pA) B SUPPLY CURRENT (mA) 04991-007 04991-008 04991-006 AD8691/AD8692/AD8694 10000 100 V = ±2.5V, ±1.35V S V = 5V S R = 2kΩ L 80 C = 15pF L 1000 60 100 40 90 AD8691_92 SINK 20 45 10 AD8694 SINK 0 0 AD8691_92 SOURCE 1 –45 –20 AD8694 SOURCE 0.1 –40 –90 1k 10k 100k 1M 10M 0.001 0.01 0.1 1 10 100 FREQUENCY (Hz) LOAD CURRENT (mA) Figure 13. Output Voltage to Supply Rail vs. Load Current Figure 16. Open-Loop Gain and Phase vs. Frequency 35 120 V = 5V V = 5V AND 2.7V S S AD8691_92 (V – V ) DD OH 30 100 AD8694 (V – V ) 25 DD OH 80 20 AD8691_92 (V ) 60 OL 15 AD8694 (V ) OL 40 10 20 5 0 0 1k 10k 100k 1M 10M –40 –20 0 20 40 60 80 100 120 FREQUENCY (Hz) TEMPERATURE (°C) Figure 14. Output Voltage Swing vs. Temperature (I = 1 mA) L Figure 17. CMRR vs. Frequency 350 120 V = 5V V = 5V AND 2.7V S S AD8691_92 (V – V ) DD OH 300 100 250 AD8694 (V – V ) DD OH 80 200 AD8691_92 (V ) 60 OL 150 AD8694 (V ) 40 OL 100 20 50 0 0 –40 –20 0 20 40 60 80 100 120 10 100 1k 10k 100k 1M 10M FREQUENCY (Hz) TEMPERATURE (°C) Figure 15. Output Voltage Swing vs. Temperature (I = 10 mA) L Figure 18. PSRR vs. Frequency Rev. E | Page 7 of 16 OUTPUT VOLTAGE TO SUPPLY RAIL (mV) OUTPUT VOLTAGE SWING (mV) OUTPUT VOLTAGE SWING (mV) 04991-011 04991-010 04991-009 PSRR (dB) CMRR (dB) OPEN-LOOP GAIN (dB) PHASE (Degrees) 04991-014 04991-013 04991-012 AD8691/AD8692/AD8694 10000 V = 5V V = ±2.5V S S C = 200pF L 1000 R = ∞ L A = 1 V A = 100 100 V 10 A = 10 V 1 A = 1 V 0.1 0.01 0.001 0.0001 100 1k 10k 100k 1M 10M TIME (400ns/DIV) FREQUENCY (Hz) Figure 19. Closed-Loop Output Impedance vs. Frequency Figure 22. Large Signal Transient Response 40 V = 5V AND 2.7V V = ±2.5V S S 35 R =∞ A = –50 L V A = –1 V 30 0 25 –2.5 20 100 15 10 0 5 0 1 10 100 1k TIME (400ns/DIV) LOAD CAPACITANCE (pF) Figure 20. Small Signal Overshoot vs. Load Capacitance Figure 23. Positive Overload Recovery V = ±2.5V, ±1.35V S V = ±2.5V S R = 10kΩ L A = –50 V C = 200pF L 2.5 A = 1 V 0 0 –100 TIME (400ns/DIV) TIME (200ns/DIV) Figure 21. Small Signal Transient Response Figure 24. Negative Overload Recovery Rev. E | Page 8 of 16 VOLTAGE (50mV/DIV) OVERSHOOT (%) IMPEDANCE (Ω) 04991-017 04991-016 04991-015 V (mV) V (V) V (mV) V (V) VOLTAGE (1V/DIV) IN OUT IN OUT 04991-020 04991-019 04991-018 AD8691/AD8692/AD8694 1000 0.1 V = ±2.5V AND ±1.35V V = ±2.5V S S A = 1 V V = 1V p-p IN BW = 20kHz 100 0.01 R = 600Ω L R = 1kΩ L 10 0.001 R = 100kΩ L 1 0.0001 1 10 100 1000 10000 20 100 1k 10k 20k FREQUENCY (Hz) FREQUENCY (Hz) Figure 25. THD + N vs. Frequency Figure 27. Voltage Noise Density 150 +2.5V R1 V = 5V AND 2.7V S 10kΩ V+ R2 140 100Ω V A IN V– 28mV p-p V– B V 130 OUT V+ –2.5V 120 110 100 90 80 1k 10k 100k 1M 10M TIME (1s/DIV) FREQUENCY (Hz) Figure 26. 0.1 Hz to 10 Hz Input Voltage Noise Figure 28. AD8692/AD8694 Channel Separation Rev. E | Page 9 of 16 VOLTAGE NOISE (1µV/DIV) THD + N (%) 04991-022 04991-021 CHANNEL SEPARATION (dB) NOISE (nV/ Hz) 04991-024 04991-023 AD8691/AD8692/AD8694 V = +2.7 V or ±1.35 V, unless otherwise noted. S 1200 60 V = 2.7V S V = 2.7V S V = –0.3V TO +1.6V CM AD8691_92 (V – V ) DD OH 1000 50 AD8694 (V – V ) DD OH 800 40 600 30 AD8691_92 (V ) OL 400 20 AD8694 (V ) OL 200 10 0 0 –2.0 –1.5 –1.0 –0.5 0 0.5 1.0 1.5 2.0 –40 –20 0 20 40 60 80 100 120 V (mV) OS TEMPERATURE (°C) Figure 29. Input Offset Voltage Distribution Figure 32. Output Voltage Swing vs. Temperature (IL = 1 mA) 2000 V = 2.7V S C = 200pF V = 2.7V L S 1600 R = T = 25°C ∞ L A A = 1 V 1200 800 400 0 –400 –800 –1200 –1600 –2000 –0.3 0 0.3 0.6 0.9 1.2 1.5 1.6 TIME (400ns/DIV) COMMON-MODE VOLTAGE (V) Figure 30. Input Offset Voltage vs. Common-Mode Voltage Figure 33. Large Signal Transient Response 10k V = 2.7V S 1k 100 AD8691_92 SINK 10 AD8694 SINK AD8691_92 SOURCE 1 AD8694 SOURCE 0.1 0.001 0.01 0.1 1 10 LOAD CURRENT (mA) Figure 31. Output Voltage to Supply Rail vs. Load Current Rev. E | Page 10 of 16 INPUT OFFSET VOLTAGE (µV) OUTPUT VOLTAGE TO SUPPLY RAIL (mV) NUMBER OF AMPLIFIERS 04991-027 04991-025 04991-026 VOLTAGE (500mV/DIV) OUTPUT VOLTAGE SWING (mV) 04991-029 04991-028 AD8691/AD8692/AD8694 OUTLINE DIMENSIONS 3.20 3.00 2.80 8 5 5.15 3.20 4.90 3.00 4.65 1 2.80 4 PIN 1 IDENTIFIER 0.65 BSC 0.95 15° MAX 0.85 1.10 MAX 0.75 0.80 0.15 0.23 6° 0.55 0.40 0.05 0.09 0° 0.40 0.25 COPLANARITY 0.10 COMPLIANT TO JEDEC STANDARDS MO-187-AA Figure 34. 8-Lead Mini Small Outline Package [MSOP] (RM-8) Dimensions shown in millimeters 5.00 (0.1968) 4.80 (0.1890) 85 6.20 (0.2441) 4.00 (0.1574) 1 5.80 (0.2284) 3.80 (0.1497) 4 0.50 (0.0196) 1.27 (0.0500) 45° BSC 1.75 (0.0688) 0.25 (0.0099) 1.35 (0.0532) 0.25 (0.0098) 8° 0.10 (0.0040) 0° COPLANARITY 0.51 (0.0201) 1.27 (0.0500) 0.10 0.31 (0.0122) 0.25 (0.0098) SEATING 0.40 (0.0157) PLANE 0.17 (0.0067) COMPLIANT TO JEDEC STANDARDS MS-012-AA CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN. Figure 35. 8-Lead Standard Small Outline Package [SOIC_N] Narrow Body (R-8) Dimensions shown in millimeters and (inches) Rev. E | Page 11 of 16 10-07-2009-B 012407-A AD8691/AD8692/AD8694 2.20 2.00 1.80 2.40 1.35 5 4 2.10 1.25 1.80 1.15 12 3 0.65 BSC 1.00 0.40 1.10 0.90 0.10 0.80 0.70 0.46 0.22 SEATING 0.10 MAX 0.30 0.36 0.08 PLANE COPLANARITY 0.26 0.15 0.10 COMPLIANT TO JEDEC STANDARDS MO-203-AA Figure 36. 5-Lead Thin Shrink Small Outline Package [SC70] (KS-5) Dimensions shown in millimeters 2.90 BSC 54 2.80 BSC 1.60 BSC 12 3 0.95 BSC 1.90 * BSC 0.90 MAX 0.70 MIN * 1.00 MAX 0.20 0.08 8° 0.10 MAX 4° 0.50 0.60 SEATING PLANE 0° 0.30 0.45 0.30 * COMPLIANT TO JEDEC STANDARDS MO-193-AB WITH THE EXCEPTION OF PACKAGE HEIGHT AND THICKNESS. Figure 37. 5-Lead Thin Small Outline Transistor Package [TSOT] (UJ-5) Dimensions shown in millimeters Rev. E | Page 12 of 16 072809-A 100708-A AD8691/AD8692/AD8694 5.10 5.00 4.90 14 8 4.50 6.40 4.40 BSC 4.30 1 7 PIN 1 0.65 BSC 1.05 1.20 1.00 0.20 MAX 0.80 0.09 0.75 0.15 8° 0.60 SEATING 0° 0.05 0.45 0.30 PLANE COPLANARITY 0.19 0.10 COMPLIANT TO JEDEC STANDARDS MO-153-AB-1 Figure 38. 14-Lead Thin Shrink Small Outline Package [TSSOP] (RU-14) Dimensions shown in millimeters 8.75 (0.3445) 8.55 (0.3366) 14 8 6.20 (0.2441) 4.00 (0.1575) 1 5.80 (0.2283) 3.80 (0.1496) 7 1.27 (0.0500) 0.50 (0.0197) 45° BSC 0.25 (0.0098) 1.75 (0.0689) 0.25 (0.0098) 1.35 (0.0531) 8° 0.10 (0.0039) 0° COPLANARITY SEATING 1.27 (0.0500) 0.51 (0.0201) 0.10 PLANE 0.25 (0.0098) 0.40 (0.0157) 0.31 (0.0122) 0.17 (0.0067) COMPLIANT TO JEDEC STANDARDS MS-012-AB CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN. Figure 39. 14-Lead Standard Small Outline Package [SOIC_N] Narrow Body (R-14) Dimensions shown in millimeters and (inches) Rev. E | Page 13 of 16 061908-A 060606-A AD8691/AD8692/AD8694 ORDERING GUIDE 1, 2 Model Temperature Range Package Description Package Option Branding AD8691AUJZ-R2 −40°C to +125°C 5-Lead TSOT UJ-5 ACA AD8691AUJZ-REEL −40°C to +125°C 5-Lead TSOT UJ-5 ACA AD8691AUJZ-REEL7 −40°C to +125°C 5-Lead TSOT UJ-5 ACA AD8691AKSZ-R2 −40°C to +125°C 5-Lead SC70 KS-5 ACA AD8691AKSZ-REEL −40°C to +125°C 5-Lead SC70 KS-5 ACA AD8691AKSZ-REEL7 −40°C to +125°C 5-Lead SC70 KS-5 ACA AD8691WAUJZ-R7 −40°C to +125°C 5-Lead TSOT UJ-5 ACA AD8691WAUJZ-RL −40°C to +125°C 5-Lead TSOT UJ-5 ACA AD8692ARMZ-R7 −40°C to +125°C 8-Lead MSOP RM-8 APA AD8692ARMZ-REEL −40°C to +125°C 8-Lead MSOP RM-8 APA AD8692ARZ −40°C to +125°C 8-Lead SOIC_N R-8 AD8692ARZ-REEL −40°C to +125°C 8-Lead SOIC_N R-8 AD8692ARZ-REEL7 −40°C to +125°C 8-Lead SOIC_N R-8 AD8692WARMZ-REEL −40°C to +125°C 8-Lead MSOP RM-8 APA AD8694ARUZ −40°C to +125°C 14-Lead TSSOP RU-14 AD8694ARUZ-REEL −40°C to +125°C 14-Lead TSSOP RU-14 AD8694WARUZ −40°C to +125°C 14-Lead TSSOP RU-14 AD8694WARUZ-REEL −40°C to +125°C 14-Lead TSSOP RU-14 AD8694ARZ −40°C to +125°C 14-Lead SOIC_N R-14 AD8694ARZ-REEL −40°C to +125°C 14-Lead SOIC_N R-14 AD8694ARZ-REEL7 −40°C to +125°C 14-Lead SOIC_N R-14 1 Z = RoHS Compliant Part. 2 W = Qualified for Automotive Applications. AUTOMOTIVE PRODUCTS The AD8691W/AD8692W/AD8694W models are available with controlled manufacturing to support the quality and reliability requirements of automotive applications. Note that these automotive models may have specifications that differ from the commercial models; therefore, designers should review the Specifications section of this data sheet carefully. Only the automotive grade products shown are available for use in automotive applications. Contact your local Analog Devices account representative for specific product ordering information and to obtain the specific Automotive Reliability reports for these models. Rev. E | Page 14 of 16 AD8691/AD8692/AD8694 NOTES Rev. E | Page 15 of 16 AD8691/AD8692/AD8694 NOTES ©2004–2011 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D04991-0-8/11(E) Rev. E | Page 16 of 16