ANALOG DEVICES AD8041

160 MHz Rail-to-Rail Amplifier with Disable AD8041 FEATURES CONNECTION DIAGRAM Fully Specified for +3 V, +5 V, and �5 V Supplies 8-Lead PDIP, CERDIP and SOIC Output Swings Rail to Rail Input Voltage Range Extends 200 mV Below Ground 1 8 No Phase Reversal with Inputs 1 V Beyond Supplies NC DISABLE Disable/Power-Down Capability –INPUT 2 7 �V S Low Power of 5.2 mA (26 mW on 5 V) 3 6 OUTPUT �INPUT High Speed and Fast Settling on 5 V: AD8041 –V 4 5 NC S (Top View) 160 MHz –3 dB Bandwidth (G = +1) NC = NO CONNECT 160 V/�s Slew Rate 30 ns Settling Time to 0.1% The output voltage swing extends to within 50 mV of each rail, Good Video Specifications (R = 150 �, G = +2) L providing the maximum output dynamic range. Additionally, it Gain Flatness of 0.1 dB to 30 MHz features gain flatness of 0.1 dB to 30 MHz while offering differ- 0.03% Differential Gain Error ential gain and phase error of 0.03% and 0.03° on a single 5 V 0.03� Differential Phase Error supply. This makes the AD8041 ideal for professional video Low Distortion electronics such as cameras, video switchers, or any high speed –69 dBc Worst Harmonic @ 10 MHz portable equipment. The AD8041’s low distortion and fast settling Outstanding Load Drive Capability make it ideal for buffering high speed A-to-D converters. Drives 50 mA 0.5 V from Supply Rails The AD8041 has a high speed disable feature useful for mul- Cap Load Drive of 45 pF tiplexing or for reducing power consumption (1.5 mA). The APPLICATIONS disable logic interface is compatible with CMOS or open- Power Sensitive High Speed Systems collector logic. The AD8041 offers a low power supply current Video Switchers of 5.8 mA maximum and can run on a single 3 V power supply. Distribution Amplifiers These features are ideally suited for portable and battery- A/D Drivers powered applications where size and power are critical. Professional Cameras The wide bandwidth of 160 MHz along with 160 V/µs of slew CCD Imaging Systems rate on a single 5 V supply make the AD8041 useful in many Ultrasound Equipment (Multichannel) general-purpose high speed applications where dual power Single-Supply Multiplexer supplies of up to ±6 V and single supplies from 3 V to 12 V are needed. The AD8041 is available in 8-lead PDIP and SOIC PRODUCT DESCRIPTION over the industrial temperature range of –40°C to +85°C. The AD8041 is a low power voltage feedback, high speed ampli- fier designed to operate on +3 V, +5 V, or ±5 V supplies. It has 2 true single-supply capability with an input voltage range extending V = 5V S 1 G = +2 200 mV below the negative rail and within 1 V of the positive rail. R = 400� 0 F –1 5V –2 –3 –4 2.5V –5 –6 –7 0V 1V 200ns –8 0 20 40 60 80 100 FREQUENCY (MHz) Figure 1. Output Swing: G = –1, V = 5 V S Figure 2. Frequency Response: G = +2, V = 5 V S REV. B Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. may result from its use. No license is granted by implication or otherwise Tel: 781/329-4700 www.analog.com under any patent or patent rights of Analog Devices. Trademarks and Fax: 781/326-8703 © 2003 Analog Devices, Inc. All rights reserved. registered trademarks are the property of their respective companies. NORMALIZED GAIN (dB) (@ T = 25�C, V = 5 V, R = 2 k� to 2.5 V, unless otherwise noted.) AD8041–SPECIFICATIONS A S L AD8041A Parameter Conditions Min Typ Max Unit DYNAMIC PERFORMANCE –3 dB Small Signal Bandwidth, V < 0.5 V p-p G = +1 130 160 MHz O Bandwidth for 0.1 dB Flatness G = +2, R = 150 Ω 30 MHz L Slew Rate G = –1, V = 2 V Step 130 160 V/µs O Full Power Response V = 2 V p-p 24 MHz O Settling Time to 0.1% G = –1, V = 2 V Step 35 ns O Settling Time to 0.01% 55 ns NOISE/DISTORTION PERFORMANCE Total Harmonic Distortion f = 5 MHz, V = 2 V p-p, G = +2, R = 1 kΩ –72 dB C O L Input Voltage Noise f = 10 kHz 16 nV/√Hz Input Current Noise f = 10 kHz 600 fA/√Hz Differential Gain Error (NTSC) G = +2, R = 150 Ω to 2.5 V 0.03 % L G = +2, R = 75 Ω to 2.5 V 0.01 % L Differential Phase Error (NTSC) G = +2, R = 150 Ω to 2.5 V 0.03 Degrees L G = +2, R = 75 Ω to 2.5 V 0.19 Degrees L DC PERFORMANCE Input Offset Voltage 27 mV T to T 8mV MIN MAX Offset Drift 10 µV/°C Input Bias Current 1.2 3.2 µA T to T 3.5 µA MIN MAX Input Offset Current 0.2 0.5 µA Open-Loop Gain R = 1 kΩ 86 95 dB L T to T 90 dB MIN MAX INPUT CHARACTERISTICS Input Resistance 160 kΩ Input Capacitance 1.8 pF Input Common-Mode Voltage Range –0.2 to +4 V Common-Mode Rejection Ratio V = 0 V to 3.5 V 74 80 dB CM OUTPUT CHARACTERISTICS Output Voltage Swing: R = 10 kΩ 0.05 to 4.95 V L Output Voltage Swing: R = 1 kΩ 0.35 to 4.75 0.1 to 4.9 V L Output Voltage Swing: R = 50 Ω 0.4 to 4.4 0.3 to 4.5 V L Output Current V = 0.5 V to 4.5 V 50 mA OUT Short-Circuit Current Sourcing 90 mA Sinking 150 mA Capacitive Load Drive G = +1 45 pF POWER SUPPLY Operating Range 312V Quiescent Current 5.2 5.8 mA Quiescent Current (Disabled) 1.4 1.7 mA Power Supply Rejection Ratio V = 0, +5 V, ±1 V 72 80 dB S DISABLE CHARACTERISTICS V = 2 V p-p @ 10 MHz, G = +2 O Turn-Off Time R = R = 2 kΩ 120 ns F L Turn-On Time R = R = 2 kΩ 230 ns F L Off Isolation (Pin 8 Tied to –V)R = 100 Ω, f = 5 MHz, G = +2, R = 1 kΩ 70 dB S L F Off Voltage (Device Disabled)