Elite.Parts Manufacturers A ANALOG DEVICES AD8004
About product Specifications Features Datasheet FAQ

ANALOG DEVICES AD8004

Description

Analog Devices AD8004 Quad, Low Power, High Speed, 3000 V/MS, 35MW Current Feedback Amplifier

Part Number

AD8004

Price

Request Quote

Manufacturer

ANALOG DEVICES

Lead Time

Request Quote

Category

PRODUCTS - A

Specifications

# OpAmps per Pkg

4

-3dB Bandwidth>

250MHz

Ib

35µA

Input Noise (nV/rtHz)

1.5nV/rtHz

Isy per Amplifier

4.25mA

Packages

DIP,SOIC

Slew Rate

3kV/µs

Vcc-Vee

4V to 12V

Vos

1mV

Features

Datasheet

pdf file

AD8004-62795669.pdf

556 KiB

Extracted Text

Quad 3000 V/�s, 35 mW a Current Feedback Amplifier AD8004 FEATURES CONNECTION DIAGRAM High Speed PDIP (N), CERDIP (Q), and 250 MHz –3 dB Bandwidth (G = +1) SOIC (R) Packages 3000 V/�s Slew Rate 21 ns Settling Time to 0.1% OUTPUT 1 14 OUTPUT 1.8 ns Rise Time for 2 V Step Low Power –IN 2 1 4 13 –IN 3.5 mA/Amp Power Supply Current (35 mW/Amp) +IN 3 12 +IN AD8004 Single Supply Operation +V 4 11 –V S S (TOP VIEW) Fully Specified for +5 V Supply +IN 5 10 +IN Good Video Specifications (R = 150 �, G = +2) L –IN –IN 6 9 23 Gain Flatness 0.1 dB to 30 MHz OUTPUT OUTPUT 7 8 0.04% Differential Gain Error 0.10� Differential Phase Error Low Distortion 30 MHz while offering differential gain and phase error of –78 dBc THD at 5 MHz 0.04% and 0.10∞. This makes the AD8004 suitable for video –61 dBc THD at 20 MHz electronics such as cameras and video switchers. High Output Current of 50 mA Available in a 14-Lead PDIP, SOIC, and CERDIP The AD8004 offers low power of 3.5 mA/amplifier and can run on a single +4 V to +12 V power supply, while being capable of APPLICATIONS delivering up to 50 mA of load current. All this is offered in a Image Scanners small 14-lead DIP or 14-lead SOIC package. These features Active Filters make this amplifier ideal for portable and battery powered appli- Video Switchers cations where size and power are critical. Special Effects The outstanding bandwidth of 250 MHz along with 3000 V/ms of slew rate make the AD8004 useful in many general-purpose, GENERAL DESCRIPTION high speed applications where dual power supplies of up to ±6V The AD8004 is a quad, low power, high speed amplifier designed and single supplies from 4 V to 12 V are needed. The AD8004 to operate on single or dual supplies. It utilizes a current feed- is available in the industrial temperature range of –40∞C to +85∞C back architecture and features high slew rate of 3000 V/ms in the N and R packages, and in the military temperature range making the AD8004 ideal for handling large amplitude pulses. of –55∞C to +125∞C in the Q package. Additionally, the AD8004 provides gain flatness of 0.1 dB to 0.04 1 0.03 0 0.02 G = +2 0.01 –1 V = 50mV rms 0.00 IN 80 IRE R = 100� –0.01 R = 150� L L �5V S –2 V = �5V R = 1.10k� –0.02 F S +5V S R = 1.21k� R PACKAGE –0.03 F 0.1 –3 –0.04 1ST 2ND 3RD 4TH 5TH 6TH 7TH 8TH 9TH 10TH 11TH 0 –4 0.12 –5 –0.1 �5V 0.10 S +5V S 0.08 –0.2 –6 0.06 0.04 80 IRE –0.3 –7 0.02 R = 150� L 0.00 V = �5V –8 S –0.4 R = 1.21k� –0.02 F –0.04 –0.5 –9 1 10 40 100 500 1ST 2ND 3RD 4TH 5TH 6TH 7TH 8TH 9TH 10TH 11TH FREQUENCY – MHz Figure 2. Differential Gain/Differential Phase Figure 1. Frequency Response and Flatness, G = +2 REV. C Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. may result from its use. No license is granted by implication or otherwise Tel: 781/329-4700 www.analog.com under any patent or patent rights of Analog Devices. Trademarks and Fax: 781/326-8703 © 2003 Analog Devices, Inc. All rights reserved. registered trademarks are the property of their respective companies. NORMALIZED FLATNESS – dB NORMALIZED FREQUENCY RESPONSE – dB DIFF PHASE – Degrees DIFF GAIN – % (@ T = +25�C, V = �5 V, R = 100 �, unless otherwise noted.) AD8004–SPECIFICATIONS A S L AD8004A AD8004S Parameter Conditions Min Typ Max Min Typ Max Unit DYNAMIC PERFORMANCE –3 dB Bandwidth, N Package G = +2, R = 698 Ω 185 MHz F G = +1, R = 806 Ω 250 MHz F Bandwidth for 0.1 dB Flatness G = +2 30 30 MHz Slew Rate G = +2, V = 4 V Step 3000 3000 V/µs O G = –2, V = 4 V Step 2000 2000 V/µs O Settling Time to 0.1% G = +2, V = 2 V Step 21 21 ns O Rise and Fall Time (10% to 90%) G = +2, V = 2 V Step 1.8 1.8 ns O NOISE/HARMONIC PERFORMANCE Total Harmonic Distortion f = 5 MHz, V = 2 V p-p, R = 1 kΩ –78 –78 dBc C O L Crosstalk, R Package, Worst Case f = 5 MHz, G = +2, R = 1 kΩ –69 dB L Crosstalk, N Package, Worst Case f = 5 MHz, G = +2, R = 1 kΩ –64 dB L Input Voltage Noise f = 10 kHz 1.5 1.5 nV/√Hz Input Current Noise f = 10 kHz, +In 38 38 pA/√Hz –In 38 38 pA/√Hz Differential Gain Error NTSC, G = +2, R = 150 Ω, R = 1.21 kΩ 0.04 0.04 % L F Differential Phase Error NTSC, G = +2, R = 150 Ω, R = 1.21 kΩ 0.10 0.10 Degree L F Differential Gain Error NTSC, G = +2, R = 1 kΩ, R = 1.21 kΩ 0.01 0.01 % L F Differential Phase Error NTSC, G = +2, R = 1 kΩ, R = 1.21 kΩ 0.04 0.04 Degree L F DC PERFORMANCE Input Offset Voltage 1.0 3.5 1.0 3.5 mV T to T 1.5 5 1.5 6 mV MIN MAX Offset Drift 15 15 µV/°C –Input Bias Current ±35 ±90 ±35 ±90 µA to T ±110 ±120 µA T MIN MAX +Input Bias Current ±40 ±110 ±40 ±110 µA T to T ±120 ±130 µA MIN MAX Open-Loop Transresistance V = ±2.5 V 170 290 170 290 kΩ O T to T 220 220 kΩ MIN MAX INPUT CHARACTERISTICS Input Resistance +Input 2 2 MΩ –Input 50 50 Ω Input Capacitance +Input 1.5 1.5 pF Input Common-Mode Voltage Range 3.2 3.2 ±V Common-Mode Rejection Ratio Offset Voltage V = ±2.5 V 52 58 52 58 dB CM –Input Current V = ±2.5 V, T to T 11 µA/V CM MIN MAX +Input Current V = ±2.5 V, T to T 12 12 µA/V CM MIN MAX OUTPUT CHARACTERISTICS Output Voltage Swing R = 150 Ω 3.9 3.9 ±V L Output Current 50 50 mA Short Circuit Current 100 180 100 180 mA POWER SUPPLY Operating Range ±2.0 ±6.0 ±2.0 ±6.0 V Total Quiescent Current 14 17 14 17 mA T to T 16 20 16 23 mA MIN MAX Power Supply Rejection Ratio ∆V = ±2 V 56 62 5662 dB S –Input Current T to T 0.5 0.5 µA/V MIN MAX +Input Current T to T 44 µA/V MIN MAX Specifications subject to change without notice. –2– REV. C AD8004 SPECIFICATIONS (@ T = +25�C, V = +5 V, R = 100 �, unless otherwise noted.) A S L AD8004A AD8004S Parameter Conditions Min Typ Max Min Typ Max Unit DYNAMIC PERFORMANCE –3 dB Bandwidth, N Package G = +2, R = 698 Ω 150 MHz F G = +1, R = 806 Ω 200 MHz F Bandwidth for 0.1 dB Flatness G = +2 30 30 MHz Slew Rate G = +2, V = 2 V Step 1100 1100 V/µs O Settling Time to 0.1% G = +2, V = 2 V Step 24 24 ns O Rise and Fall Time (10% to 90%) G = +2, V = 2 V Step 2.3 2.3 ns O NOISE/HARMONIC PERFORMANCE Total Harmonic Distortion f = 5 MHz, V = 2 V p-p, R = 1 kΩ –65 –65 dBc C O L Crosstalk, R Package, Worst Case f = 5 MHz, G = +2, R = 1 kΩ –69 dB L Crosstalk, N Package, Worst Case f = 5 MHz, G = +2, R = 1 kΩ –64 dB L Input Voltage Noise f = 10 kHz 1.5 1.5 nV/√Hz Input Current Noise f = 10 kHz, +In 38 38 pA/√Hz –In 38 38 pA/√Hz Differential Gain Error NTSC, G = +2, R = 150 Ω, R = 1.21 kΩ 0.06 0.06 % L F Differential Phase Error NTSC, G = +2, R = 150 Ω, R = 1.21 kΩ 0.25 0.25 Degree L F Differential Gain Error NTSC, G = +2, R = 1 kΩ, R = 1.21 kΩ 0.01 0.01 % L F Differential Phase Error NTSC, G = +2, R = 1 kΩ, R = 1.21 kΩ 0.08 0.08 Degree L F DC PERFORMANCE Input Offset Voltage 1.0 2.5 1.0 2.5 mV T to T 13 14 mV MIN MAX Offset Drift 15 15 µV/°C –Input Bias Current ±20 ±80 ±20 ±80 µA T to T ±100 ±110 µA MIN MAX +Input Bias Current ±35 ±100 ±35 ±100 µA T to T ±115 ±125 µA MIN MAX Open Loop Transresistance V = +1.5 V to +3.5 V 140 230 140 230 kΩ O T to T 170 170 kΩ MIN MAX INPUT CHARACTERISTICS Input Resistance +Input 2 2 MΩ –Input 50 50 Ω Input Capacitance +Input 1.5 1.5 pF Input Common-Mode Voltage Range 3.2 3.2 V Common-Mode Rejection Ratio Offset Voltage V =+1Vto+3V 5257 52 57dB CM –Input Current V = +1 V to +3 V, T to T 22 µA/V CM MIN MAX +Input Current V = +1 V to +3 V, T to T 15 15 µA/V CM MIN MAX OUTPUT CHARACTERISTICS Output Voltage Swing R = 150 Ω 0.9 to 4.1 0.9 to 4.1 V L Output Current 50 50 mA Short Circuit Current 95 95 mA POWER SUPPLY Operating Range 0, +4 +12 0, +4 +12 V Total Quiescent Current 13 14 13 14 mA T to T 14.5 15.5 14.5 17.5 mA MIN MAX Power Supply Rejection Ratio ∆V = +1 V, V = +2.5 V 56 62 56 62 dB S CM –Input Current T to T 11 µA/V MIN MAX +Input Current T to T 66 µA/V MIN MAX Specifications subject to change without notice. REV. C –3– AD8004 1 ABSOLUTE MAXIMUM RATINGS MAXIMUM POWER DISSIPATION Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.6 V The maximum power that can be safely dissipated by the Internal Power Dissipation . . . . . . . . . . . . . . . . . . . . . Note 2 AD8004 is limited by the associated rise in junction temperature. Input Voltage (Common Mode) . . . . . . . . . . . . . . . . . . . . ±V S The maximum safe junction temperature for plastic encapsu- Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . ±2.5 V lated devices is determined by the glass transition temperature Output Short Circuit Duration of the plastic, approximately +150°C. Exceeding this limit . . . . . . . . . . . . . . . . . . . . . . Observe Power Derating Curves temporarily may cause a shift in parametric performance due to Storage Temperature Range (N, Q, R) . . . . –65°C to +125°C a change in the stresses exerted on the die by the package. Operating Temperature Range Exceeding a junction temperature of +175°C for an extended A Grade . . . . . . . . . . . . . . . . . . . . . . . . . . . . –40°C to +85°C period can result in device failure. S Grade . . . . . . . . . . . . . . . . . . . . . . . . . . . –55°C to +125°C While the AD8004 is internally short circuit protected, this may Lead Temperature Range (Soldering 10 sec) . . . . . . . . +300°C not be sufficient to guarantee that the maximum junction tem- NOTES perature is not exceeded under all conditions. To ensure proper 1 Stresses above those listed under Absolute Maximum Ratings may cause perma- operation, it is necessary to observe the maximum power ratings. nent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. 2 Specification is for device in free air: 14-Lead PDIP Package: θ = 90°C/W, θ = 30°C/W JA JC 14-Lead SOIC Package: θ = 140°C/W, θ = 30°C/W JA JC 14-Lead CERDIP Package: θ = 110°C/W, θ = 30°C/W JA JC ORDERING GUIDE Temperature Package Package Model Range Description Option AD8004AN –40°C to +85°C 14-Lead PDIP N-14 AD8004AR-14 –40°C to +85°C 14-Lead SOIC R-14 AD8004AR-14-REEL –40°C to +85°C 13" Tape and Reel R-14 AD8004AR-14-REEL7 –40°C to +85°C 7" Tape and Reel R-14 AD8004SQ –55°C to +125°C 14-Lead CERDIP Q-14 CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the AD8004 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. SCOPE SCOPE 604� 50� 249� 499� 50� INPUT 604� INPUT V IN 50� 50� 61.9� V IN +V +V S S 50� 0.1�F 0.1�F 10�F 10�F 0.1�F 10�F 0.1�F 10�F –V –V S S Figure 4. Test Circuit; Gain = –2 Figure 3. Test Circuit; Gain = –2 –4– REV. C Typical Performance Characteristics–AD8004 TPC 1.* 100 mV Step Response; G = +2, V = ±2.5 V or ±5 V S TPC 4.* 100 mV Step Response; G = –2, V = ±2.5 V or ±5 V S TPC 2.* Step Response; G = +2, V = ±5 V S TPC 5.* Step Response; G = –2, V = ±5 V S 2 1 G = +1, G = –1 R = 698� 1 F 0 V = �5V –1 S 0 R = 499� G = –2 F R = 100� L –2 V = 50mV rms –1 IN V = 50mV (G = +1, +2) IN R = 100� L V = 5mV (G = +10) –2 –3 IN N PACKAGE G = +2, G = –10 –4 –3 R = 604� F –4 –5 –5 –6 G = +10, R = 499� –6 –7 F –7 –8 –9 –8 1 10 40 100 500 1 10 40 100 500 FREQUENCY – MHz FREQUENCY – MHz TPC 3. Frequency Response; G = +1, +2, +10; V = ±5 V S TPC 6. Frequency Response; G = –1, –2, –10 *V = ±2.5 V operation is identical to V = +5 V single-supply operation. S S REV. C –5– NORMALIZED FREQUENCY RESPONSE – dB NORMALIZED FREQUENCY RESPONSE – dB AD8004 9 3 1V rms 6 0 3 –3 1V rms 0 –6 –3 –9 –12 –6 –9 –15 –12 –18 G = +2 G = +2 V = �5V V = +5V –15 S –21 S R = 604� R = 604� F F –18 –24 –21 –27 1 10 40 100 500 1 10 40 100 500 FREQUENCY – MHz FREQUENCY – MHz TPC 7. Large Signal Frequency Response; V = ±5.0 V, TPC 10. Large Signal Frequency Response; V = +5.0 V, S S G = +2, R = 604 Ω G = +2, R = 604 Ω F F –40 –40 3RD G = +2 G = +2 R = 150� V = 2V p-p L O 2ND V = 2V p-p –50 –50 O R = 698� R = 150� F L 3RD R = 698� F R = 150� L 2ND 3RD –60 –60 R = 1k� R = 150� L L –70 –70 –80 –80 2ND R = 1k� 2ND L –90 R = 1k� –90 L 3RD R = 1k� L –100 –100 12 100 12 100 FREQUENCY – MHz FREQUENCY – MHz TPC 11. Distortion vs. Frequency; V = +5 V S TPC 8. Distortion vs. Frequency; V = ±5 V S –10 1 604� �5V S –15 604� 0 V 50� IN G = +2 154� V OUT –20 –1 V = 50mV rms IN R = 100� L 57.6� 154� �5V +5V –2 –25 S S R = 1.10k� F +5V S R PACKAGE –30 0.1 –3 0 –4 –35 –40 –0.1 –5 +5V �5V S S –6 –45 –0.2 +5V S –7 –50 –0.3 –8 –55 –0.4 �5V S –9 –60 –0.5 1 10 40 100 500 0.03 0.1 110 100 500 FREQUENCY – MHz FREQUENCY – MHz TPC 12. CMRR vs. Frequency; V = ±5 V or +5 V, TPC 9. Frequency Response and Flatness, G = +2 S V = 200 mV rms, Other Sides Are Equal, RTO IN –6– REV. C NORMALIZED FLATNESS – dB DISTORTION – dBc OUTPUT LEVEL – dBV NORMALIZED FREQUENCY RESPONSE – dB DISTORTION – dBc OUTPUT LEVEL – dBV CMRR – dB AD8004 100 1000 0 G = +2 �5V OR �2.5V S S –10 R = 1k� 500 F 100mV rms ON TOP –20 OF dc BIAS 300 +PSRR 200 –30 10 100 –40 –PSRR 70 + OR – INPUT –50 CURRENT NOISE 50 40 –60 30 20 VOLTAGE NOISE –70 10 1 –80 10 100 1k 10k 100k 1M 10k 100k 1M 10M 100M 500M FREQUENCY – Hz FREQUENCY – Hz TPC 13. Noise vs. Frequency, V = +5 V or ±5 V TPC 16. PSRR vs. Frequency S S –20 G = +2 –30 R = 1.10k� 100 F �5V S R = 50� –40 V = 200mV rms BT IN G = +2 �5V OR +5V INPUT TO SIDE 1 S S –50 OUTPUT = R = 698� R = 1k� F L1 10 SIDE 2 POWER = 0dBm R PACKAGE –60 OUTPUT = (224mV rms) SIDE 4 R = 0 BT –70 +5V S 1 –80 OUTPUT = –90 SIDE 3 0.1 �5V S –100 –110 0.01 –120 0.03 0.03 0.1 1 10 100 500 0.1 110 100 500 FREQUENCY – MHz FREQUENCY – MHz TPC 14. Output Impedance vs. Frequency TPC 17. Crosstalk (Output to Output) vs. Frequency 110 0 60 100 GAIN GAIN 50 90 0 90 40 80 30 70 –50 PHASE PHASE –180 20 60 10 50 –100 –240 V = –40dBm 0 40 IN V = �5V S –10 30 –150 –360 20 10 –200 0.03 0.1 110 100 500 100k 1M 10M 100M 1G FREQUENCY – MHz FREQUENCY – Hz TPC 15. Open-Loop Voltage Gain and Phase TPC 18. Open-Loop Transimpedance Gain REV. C –7– PHASE – Degrees IMPEDANCE – � INPUT VOLTAGE NOISE – nV/ Hz GAIN – dB INPUT CURRENT NOISE – pA/ Hz PSRR – dB CROSSTALK – dB GAIN – dB� PHASE – Degrees AD8004 9 G = +2 8 R = 1.21k� �5V F S 7 6 5 4 3 +5V S 2 1 0 10 100 1000 10000 LOAD RESISTANCE – � TPC 22. Output Voltage Swing vs. Load TPC 19. Short-Term Settling Time 10 9 G = +2 R = 1.21k� F 8 f = 100kHz R = 1k� L 7 6 R = 100� L 5 4 3 2 1 0 34567 8 9 10 11 12 TOTAL SUPPLY VOLTAGE – V TPC 20. Long-Term Settling Time TPC 23. Output Swing vs. Supply 0.03 0.04 80 IRE 0.03 0.02 R = 1k� L 0.02 V = �5V 0.01 S 0.01 R = 1.21k� 80 IRE F 0.00 0.00 R = 150� L –0.01 V = �5V –0.01 S –0.02 R = 1.21k� F –0.02 –0.03 –0.04 –0.03 1ST 2ND 3RD 4TH 5TH 6TH 7TH 8TH 9TH 10TH 11TH 1ST 2ND 3RD 4TH 5TH 6TH 7TH 8TH 9TH 10TH 11TH 0.04 0.12 0.10 0.03 0.02 0.08 0.01 0.06 80 IRE 0.00 0.04 R = 150� L 80 IRE –0.01 0.02 V = �5V R = 1k� S L –0.02 0.00 V = �5V R = 1.21k� S F –0.02 –0.03 R = 1.21k� F –0.04 –0.04 1ST 2ND 3RD 4TH 5TH 6TH 7TH 8TH 9TH 10TH 11TH 1ST 2ND 3RD 4TH 5TH 6TH 7TH 8TH 9TH 10TH 11TH TPC 21. Differential Gain/Differential Phase TPC 24. Differential Gain/Phase, R = 1 kΩ L –8– REV. C DIFF PHASE – Degrees DIFF GAIN – % DIFF PHASE – Degrees DIFF GAIN – % PEAK-TO-PEAK OUTPUT AT CLIPPING POINT – V SWING – V p-p AD8004 THEORY OF OPERATION The more exact relationships that take into account open-loop The AD8004 is a member of a new family of high speed current- gain errors are: feedback (CF) amplifiers offering new levels of bandwidth, G distortion, and signal-swing capability vs. power. Its wide dynamic A = V range capabilities are due to both a complementary high speed 1− G R F for inverting (G is negative) 1+ + bipolar process and a new design architecture. The AD8004 is A (s) T (s) O O basically a two stage (Figure 30) rather than the conventional one stage design. Both stages feature the current-on-demand G A = property associated with current feedback amplifiers. This V G R F for noninverting (G is positive) gives an unprecedented ratio of quiescent current to dynamic 1+ + A (s) T (s) O O performance. The important properties of slew rate and full power bandwidth benefit from this performance. In addition In these equations the open-loop voltage gain (A (s)) is common O the second gain stage buffers the effects of load impedance, to both voltage and current-feedback amplifiers and is the ratio significantly reducing distortion. of output voltage to differential input voltage. The open-loop A full discussion of this new amplifier architecture is available on transimpedance gain (T (s)) is the ratio of output voltage to O the data sheet for the AD8011. This discussion only covers the inverting input current and is applicable to current-feedback basic principles of operation. amplifiers. The open-loop voltage gain and open-loop transim- pedance gain (T (s)) of the AD8004 are plotted vs. frequency O DC AND AC CHARACTERISTICS in TPCs 15 and 18. These plots and the basic relationships can As with traditional op amp circuits the dc closed-loop gain is be used to predict the first order performance of the AD8004 over defined as: frequency. At low closed-loop gains the term (R /T (s)) dominates F O the frequency response characteristics. This gives the result that R bandwidth is constant with gain, a familiar property of current F A = G = 1+ noninverting operation V R feedback amplifiers. N An R of 1 k� has been chosen as the nominal value to give F R F optimum frequency response with acceptable peaking at gains of A = G =− inverting operation V R N +2/–1. As can be seen from the above relationships, at higher closed-loop gains reducing R has the effect of increasing closed- F loop bandwidth. Table I gives optimum values for R and R F G for a variety of gains. A1 C D IPP IPN IQ1 A2 C 1 P Q3 C 2 P ICQ + IO Q1 V V P N V O´ Z I A3 V O R L C L Z2 Q2 R F IE R G Q4 IQ1 A2 C 1 P IPN INP A1 C D AD8004 Figure 5. Simplified Block Diagram REV. C –9– AD8004 DRIVING CAPACITIVE LOADS region of the summing junction will cause some bandwidth The AD8004 was designed primarily to drive nonreactive loads. extension and/or increased peaking. In noninverting gains, the If driving loads with a capacitive component is desired, best effect of extra capacitance on summing junctions is far more settling response is obtained by the addition of a small series pronounced than with inverting gains. Figure 9 shows an example resistance as shown in Figure 6. The accompanying graph shows of this. Note that only 1 pF of added junction capacitance causes the optimum value for R vs. capacitive load. It is worth about a 70% bandwidth extension and additional peaking on a SERIES noting that the frequency response of the circuit when driving gain = +2. For an inverting gain = –2, 5 pF of additional summing large capacitive loads will be dominated by the passive roll-off of junction capacitance caused a small 10% bandwidth extension. R and C . SERIES L Extra output capacitive loading also causes bandwidth exten- 1k� sions and peaking. The effect is more pronounced with less resistive loading from the next stage. Figure 10 shows the effect R SERIES of direct output capacitive loads for gains of +2 and –2. For both 1k� AD8004 gains C was set to 10 pF or 0 pF (no extra capacitive loading). LOAD R L C L For each of the four traces in Figure 10 the resistive loads were 1k� 100 �. Figure 11 also shows capacitive loading effects with a lighter output resistive load. Note that even though bandwidth is extended 2¥, the flatness dramatically suffers. Figure 6. Driving Capacitive Load 2 40 R = 698� F 1 G = +1 R = 1.1k� F 0 R = 909� F –1 30 1 R = 604� –2 F G = +2 0 –3 –4 –1 V = 50mV rms IN R = 1.10k� F 20 –2 V = �5V –5 S R = 100� L –6 –3 R PACKAGE R = 845� F –7 –4 –5 –8 10 1 10 40 100 500 01 50152025 FREQUENCY – MHz C – pF L Figure 8. R vs. Frequency Response, G = +1/+2 FEEDBACK Figure 7. Recommended R vs. Capacitive Load for SERIES £ 30 ns Settling to 0.1% 2 OPTIMIZING FLATNESS G = +2 C = 1pF J 0 The fine scale gain flatness and –3 dB bandwidth is affected by C = 0 2 J –2 R selection as is normal of current feedback amplifiers. FEEDBACK G = –2 With the exception of gain = +1, the AD8004 can be adjusted 0 –4 for either maximal flatness with modest closed-loop bandwidth –2 –6 or for mildly peaked-up frequency response with much more V = 50mV rms IN –4 R = 100� –8 bandwidth. Figure 8 shows the effect of three evenly spaced R L F �5V C = 5.1pF S J changes upon gain = +1 and gain = +2. Table I shows the –6 –10 recommended component values for achieving maximally flat –8 –12 frequency response as well as a faster slightly peaked-up fre- C = 0 J –14 –10 quency response. –12 Printed circuit board parasitics and device lead frame parasitics also control fine scale gain flatness. The AD8004R package, –14 1 10 40 100 500 because of its small lead frame, offers superior parasitics relative FREQUENCY – MHz to the N package. In the printed circuit board environment, Figure 9. Frequency Response vs. Added Summing parasitics such as extra capacitance caused by two parallel and Junction Capacitance vertical flat conductors on opposite PC board sides in the REV. C –10– R – � SERIES NORMALIZED GAIN – dB, G = –2 NORMALIZED GAIN – dB, G = +2 GAIN – dB, G = +1 NORMALIZED GAIN – dB, G = +2 AD8004 2 through R2. This current flows toward the summing junction G = +2, R = 1.10k� F C = 10pF L and requires that the output be 2 V higher than the summing 0 junction or at 3.6 V. 2 –2 C = 0 L G = –2, R = 698� F When the input is at 1 V, there is 1.2 mA flowing into the sum- 0 –4 ming junction through R3 and 1.2 mA flowing out through R1. –2 –6 These currents balance and leave no current to flow through C = 10pF L –4 –8 R2. Thus the output is at the same potential as the inverting V = 50mV IN input or 1.6 V. –6 �5V –10 S R = 100� L C = 0 The input of the AD876 has a series MOSFET switch that turns L –12 –8 on and off at the sampling rate. This MOSFET is connected to –10 –14 a hold capacitor internal to the device. The on impedance of the –12 MOSFET is about 50 Ω, while the hold capacitor is about 5 pF. –14 In a worst case condition, the input voltage to the AD876 will 1 10 40 100 500 FREQUENCY – MHz change by a full-scale value (2 V) in one sampling cycle. When the input MOSFET turns on, the output of the op amp will be Figure 10. Frequency Response vs. Capacitive Loading, connected to the charged hold capacitor through the series R = 100 Ω Output L resistance of the MOSFET. Without any other series resistance, the instantaneous current that flows would be 40 mA. This 2 C = 10pF L would cause settling problems for the op amp. 0 The series 100 Ω resistor limits the current that flows instanta- G = +2 neously after the MOSFET turns on to about 13 mA. This –2 R = 1k� L resistor cannot be made too large or the high frequency perfor- �5V S –4 V = 50mV rms IN mance will be affected. R = 1.2k� C = 0 L F –6 The sampling MOSFET of the AD876 is closed for only half of each cycle or for 25 ns. Approximately seven time constants are –8 required for settling to 10 bits. The series 100 Ω resistor along with the 50 Ω on resistance and the hold capacitor, create a –10 750 ps time constant. These values leave a comfortable margin –12 for settling. Obtaining the same results with the op amp A/D combination as compared to driving with a signal generator –14 1 10 40 100 500 indicates that the op amp is settling fast enough. FREQUENCY – MHz Overall the AD8004 provides adequate buffering for the AD876 Figure 11. Flatness with 10 pF Capacitive Load A/D converter without introducing distortion greater than that of the A/D converter by itself. DRIVING A SINGLE-SUPPLY A/D CONVERTER New CMOS A/D converters are placing greater demands on the +5V amplifiers that drive them. Higher resolutions, faster conversion rates, and input switching irregularities require superior settling R3 R2 1.65k� 1k� 0.1�F 10�F characteristics. In addition, these devices run off a single +5 V 3.6V supply and consume little power, so good single-supply operation 0.1�F +3.6V with low power consumption is very important. The AD8004 is R1 V 499k� IN REFT 1V well positioned for driving this new class of A/D converters. 0V 100� 1/4 50� Figure 12 shows a circuit that uses an AD8004 to drive an AD876 AD8004 3.6V AD876, a single supply, 10-bit, 20 MSPS A/D converter that REFB 0.1�F 1.6V requires only 140 mW. Using the AD8004 for level shifting and +1.6V driving, the A/D exhibits no degradation in performance com- 1.6V pared to when it is driven from a signal generator. Figure 12. AD8004 Driving the AD876 The analog input of the AD876 spans 2 V centered at about LAYOUT CONSIDERATIONS 2.6 V. The resistor network and bias voltages provide the level The specified high speed performance of the AD8004 requires shifting and gain required to convert the 0 V to 1 V input signal careful attention to board layout and component selection. to a 3.6 V to 1.6 V range that the AD876 wants to see. Table I shows the recommended component values for the Biasing the noninverting input of the AD8004 at 1.6 V dc forces AD8004 and Figures 14–16 show the layout for the AD8004 the inverting input to be at 1.6 V dc for linear operation of the evaluation boards (14-lead DIP and SOIC). Proper R design F amplifier. When the input is at 0 V, there is 3.2 mA flowing out techniques and low parasitic component selection are mandatory. of the summing junction via R1 (1.6 V/499 Ω). R3 has a current of 1.2 mA flowing into the summing junction (3.6 V – 1.6 V)/ 1.65 kΩ. The difference of these two currents (2 mA) must flow REV. C –11– NORMALIZED GAIN – dB, G = 2 NORMALIZED GAIN – dB, G = –2 NORMALIZED GAIN – dB, G = +2 AD8004 The PCB should have a ground plane covering all unused portions R R R , 50� G F BT of the component side of the board to provide a low impedance V V IN OUT R T ground path. The ground plane should be removed from the 1/4 area near the input pins to reduce stray capacitance. +V S C1 C3 Chip capacitors should be used for supply bypassing (see 0.1�F 10�F Figure 13). One end should be connected to the ground plane and C2 C4 the other within 1/8" of each power pin. An additional (4.7 µF to 0.1�F 10�F –V S 10 µF) tantalum electrolytic capacitor should be connected in INVERTING CONFIGURATION parallel. R RF R , 50� G BT The feedback resistor should be located close to the inverting V OUT input pin in order to keep the stray capacitance at this node to a 1/4 minimum. Capacitance greater than 1 pF at the inverting input V IN +V S will significantly affect high speed performance when operating C1 C3 R T 0.1�F 10�F at low noninverting gains. An example of extra inverting input C2 C4 capacitance can be seen on the plot of Figure 10. 0.1�F 10�F –V S Stripline design techniques should be used for long signal traces NONINVERTING CONFIGURATION (greater than about 1"). These should be designed with the Figure 13. Inverting and Noninverting Configurations proper system characteristic impedance and be properly termi- nated at each end. 1 Table I. Recommended Component Values and Typical Bandwidths Alternate Alternate Alternate Alternate Gain –10 –2 –2 –1 –1 +1 +1 +2 +2 +10 AD8004 (DIP) PACKAGE TYPE R (Ω) 499 698 499 649 499 1.21 k 806 1.10 k 698 499 F (Ω) 49.9 348 249 649 499 1.10 k 698 54.9 R G 2 R (Ω) None 57.6 61.9 53.6 54.9 50 50 50 50 50 T Small Signal BW @ ±5 V (MHz) 155 125 180 135 190 150 250 115 185 135 S < 0.3 dB None 0.3 dB None 0.3 dB 1.3 dB 1.7 dB < 0.14 dB 0.4 dB < 0.3 dB Peaking @ ±5 V S 0.1 dB Flatness @ ±5 V (MHz) 25 30 35 S Small Signal BW @ +5 V (MHz) 135 105 155 120 160 130 200 95 150 120 S AD8004 (SOIC) PACKAGE TYPE R (Ω) 499 698 499 750 499 1.10 k 698 1.10 k 604 499 F (Ω) 49.9 348 249 750 499 1.10 k 604 54.9 R G 2 R (Ω) None 57.6 61.9 53.6 54.9 50 50 50 50 50 T Small Signal BW @ ±5 V (MHz) 155 130 190 125 195 150 225 110 175 135 S < 0.7 dB < 0.1 dB 0.5 dB None 0.4 dB 1.3 dB 1.8 dB < 0.1 dB 0.5 dB < 0.2 dB Peaking @ ±5 V S 0.1 dB Flatness @ ±5 V (MHz) 35 25 30 S Small Signal BW @ +5 V (MHz) 135 115 175 110 165 130 195 95 155 120 S NOTES 1 Resistor values listed are standard 1% tolerance. 2 R chosen for 50 Ω characteristic input impedance. T –12– REV. C AD8004 Figure 14. Evaluation Board Silkscreen (Top) REV. C –13– AD8004 Figure 15 Evaluation Board Layout (Top Side) Figure 16. Evaluation Board Layout (Bottom Side, Looking Through the Board) –14– REV. C AD8004 OUTLINE DIMENSIONS 14-Lead Plastic Dual In-Line Package [PDIP] 14-Lead Standard Small Outline Package [SOIC] (N-14) (R-14) Dimensions shown in inches and (millimeters) Dimensions shown in millimeters and (inches) 0.685 (17.40) 8.75 (0.3445) 0.665 (16.89) 0.295 (7.49) 8.55 (0.3366) 0.645 (16.38) 0.285 (7.24) 0.275 (6.99) 8 14 14 8 4.00 (0.1575) 6.20 (0.2441) 3.80 (0.1496) 1 7 5.80 (0.2283) 1 7 0.100 (2.54) BSC 0.325 (8.26) 1.75 (0.0689) 1.27 (0.0500) 0.50 (0.0197) � 45� BSC 0.310 (7.87) 1.35 (0.0531) 0.25 (0.0098) 0.25 (0.0098) 0.015 (0.38) 0.300 (7.62) 0.150 (3.81) 0.10 (0.0039) MIN 0.135 (3.43) 8� 0.180 (4.57) 0.120 (3.05) 0.51 (0.0201) 0� SEATING 1.27 (0.0500) MAX 0.25 (0.0098) COPLANARITY PLANE 0.33 (0.0130) 0.40 (0.0157) 0.10 0.19 (0.0075) 0.150 (3.81) SEATING 0.130 (3.30) 0.015 (0.38) PLANE COMPLIANT TO JEDEC STANDARDS MS-012AB 0.022 (0.56) 0.060 (1.52) 0.110 (2.79) 0.010 (0.25) CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS 0.018 (0.46) 0.050 (1.27) 0.008 (0.20) (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR 0.045 (1.14) 0.014 (0.36) REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN COMPLIANT TO JEDEC STANDARDS MO-095-AB CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN 14-Lead Ceramic Dual In-Line Package [CERDIP] (Q-14) Dimensions shown in inches and (millimeters) 0.098 (2.49) MAX 0.005 (0.13) MIN 14 8 0.310 (7.87) PIN 1 0.220 (5.59) 17 0.320 (8.13) 0.100 (2.54) BSC 0.290 (7.37) 0.060 (1.52) 0.785 (19.94) MAX 0.015 (0.38) 0.200 (5.08) MAX 0.150 0.200 (5.08) (3.81) MIN 0.125 (3.18) 0.015 (0.38) SEATING 0.023 (0.58) 0.070 (1.78) 15 0.008 (0.20) PLANE 0 0.014 (0.36) 0.030 (0.76) CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETERS DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN REV. C –15– AD8004 Revision History Location Page 3/03—Data Sheet changed from REV. B to REV. C. Updated format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Universal Added CERDIP (Q) Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Added text to GENERAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Changes to SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Changes to ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Changes to ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Edited MAXIMUM POWER DISSIPATION section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Deleted Figure 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Edited Y axis of TPC 13 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Edited OPTIMIZING FLATNESS section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Edits to Figure 13 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Changes to Table I . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Updated OUTLINE DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 REV. C –16– PRINTED IN U.S.A. C01045–0–3/03(C)

Frequently asked questions

What makes Elite.Parts unique?

chervon down
At GID Industrial (Elite.Parts' parent company), we specialize in procuring industrial parts. We know where to find the rare and obsolete equipment that our customers need in order to get back to business. There are other companies who claim to do what we do, but we're confident that our commitment to quality and value is unparalleled in our field.

What kind of warranty will the AD8004 have?

chervon down
Warranties differ by part and by which suppliers we use to procure it for you. Sometimes, a part will be sold as-is and without a warranty. Our specialty, single board computers, tend to receive a one-year warranty.

Which carriers does Elite.Parts work with?

chervon down
Elite.Parts can ship via FedEx, UPS, DHL, and USPS. We have accounts with each of them and generally ship using one of those, but we can also ship using your account if you would prefer. However, we can use other carriers if it will be more convenient for you.

Will Elite.Parts sell to me even though I live outside the USA?

chervon down
Absolutely! We are happy to serve customers regardless of location. We work with international clients all the time, and we are familiar with shipping to destinations all across the globe.

I have a preferred payment method. Will Elite.Parts accept it?

chervon down
All major credit cards are accepted: Visa, MasterCard, Discover, and American Express. We will also accept payment made with wire transfer or PayPal. Checks will only be accepted from customers in the USA. Terms may available for larger orders, upon approval.

Why buy from GID?

quality

Quality

We are industry veterans who take pride in our work

protection

Protection

Avoid the dangers of risky trading in the gray market

access

Access

Our network of suppliers is ready and at your disposal

savings

Savings

Maintain legacy systems to prevent costly downtime

speed

Speed

Time is of the essence, and we are respectful of yours

What they say about us

FANTASTIC RESOURCE

star star star star star

One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!

Bucher Emhart Glass

EXCELLENT SERVICE

star star star star star

With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.

Fuji

HARD TO FIND A BETTER PROVIDER

star star star star star

Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.

Applied Materials

CONSISTENTLY DELIVERS QUALITY SOLUTIONS

star star star star star

Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.

Nidec Vamco

TERRIFIC RESOURCE

star star star star star

This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.

Trican Well Service

GO TO SOURCE

star star star star star

When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.

ConAgra Foods

Related Products

ANALOG DEVICE# A5E1032

SOCKET FOR MODEL AD210 IC

TRANSFORMER CURRENT 60.0 AMP

SOCKET FOR MODEL 1B22 IC

product

Analog Devices AD7291 12-Bit Low power 8-Channel Successive Approximation Analog-to-Digital Converte...