Elite.Parts Manufacturers A ANALOG DEVICES AD7988-1
About product Specifications Features Datasheet FAQ

ANALOG DEVICES AD7988-1

Description

Analog Devices AD7988-1 16-bit successive approximation analog-to-digital converters that operate from a single power supply

Part Number

AD7988-1

Price

Request Quote

Manufacturer

ANALOG DEVICES

Lead Time

Request Quote

Category

PRODUCTS - A

Specifications

Absolute Input Voltage Min

-0.1

Analog Input CMRR

60 dB

Differential Linearity Error

min: -0.9; Typ:±0.4; Max:+0.9

Gain Error Temperature Drift

±0.35 ppm/°C

Gain Error, TMIN to TMAX2

±2

Integral Linearity Error

Min: -1.25; Typ:±0.6; Max: +1.25

Leakage Current at 25°C

Acquisition phase

No Missing Codes

16 Bits

Transition Noise

0.6

Voltage Range

0 Min

Zero Temperature Drift

0.54 ppm/°C

Features

Datasheet

pdf file

AD7988-1-1199035732.pdf

522 KiB

Extracted Text

16-Bit Lower Power PulSAR ADCs in MSOP/LFCSP (QFN) Data Sheet AD7988-1/AD7988-5 FEATURES GENERAL DESCRIPTION Low power dissipation The AD7988-1/AD7988-5 are 16-bit, successive approximation, AD7988-5: 3.5 mW @ 500 kSPS analog-to-digital converters (ADC) that operate from a single AD7988-1: 700 μW @ 100 kSPS power supply, VDD. The AD7988-1 offers a 100 kSPS throughput, 16-bit resolution with no missing codes and the AD7988-5 offers a 500 kSPS throughput. They are low Throughput: 100 kSPS/500 kSPS options power, 16-bit sampling ADCs with a versatile serial interface INL: ±0.6 LSB typical, ±1.25 LSB maximum port. On the CNV rising edge, they sample an analog input, SINAD: 91.5 dB @ 10 kHz IN+, between 0 V to V with respect to a ground sense, IN−. REF THD: −114 dB @ 10 kHz The reference voltage, REF, is applied externally and can be set Pseudo differential analog input range independent of the supply voltage, VDD. 0 V to V with V from 2.5 V to 5.5 V REF REF The SPI-compatible serial interface also features the ability to Any input range and easy to drive with the ADA4841-1 daisy-chain several ADCs on a single 3-wire bus using the SDI No pipeline delay input. It is compatible with 1.8 V, 2.5 V, 3 V, or 5 V logic using Single-supply 2.5 V operation with 1.8 V/2.5 V/3 V/5 V the separate supply, VIO. logic interface The AD7988-1/AD7988-5 generics are housed in a 10-lead SPI-/QSPI-/MICROWIRE™-/DSP-compatible serial interface MSOP or a 10-lead LFCSP (QFN) with operation specified Daisy-chain multiple ADCs from −40°C to +125°C. 10-lead MSOP and 10-lead, 3 mm × 3 mm LFCSP (QFN), same space as SOT-23 Table 1. MSOP, LFCSP (QFN) 14-/16-/18-Bit PulSAR® ADCs Wide operating temperature range: −40°C to +125°C 250 400 kSPS to ≥1000 Bits 100 kSPS kSPS 500 kSPS kSPS ADC Driver APPLICATIONS 1 2 2 2 18 AD7691 AD7690 AD7982 ADA4941-1 Battery-powered equipment 2 AD7984 ADA4841-1 1 2 2 Low power data acquisition systems 16 AD7684 AD7687 AD7688 ADA4941-1 2 Portable medical instruments AD7693 ADA4841-1 3 2 2 2 16 AD7680 AD7685 AD7686 AD7980 ADA4841-1 ATE equipment 2 AD7683 AD7694 AD7988-5 ADA4841-1 Data acquisitions 2 AD7988-1 ADA4841-1 Communications 3 2 2 14 AD7940 AD7942 AD7946 ADA4841-1 1 True differential. 2 Pin-for-pin compatible. 3 Pseudo differential. TYPICAL APPLICATION DIAGRAM 2.5V TO 5V 2.5V REF VDD VIO 1.8V TO 5.5V 0V TO V REF SDI IN+ AD7988-1/ SCK 3- OR 4-WIRE INTERFACE AD7988-5 IN– (SPI, DAISY CHAIN, CS) SDO GND CNV Figure 1. Rev. A Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. rights of third parties that may result from its use. Specifications subject to change without notice. No Tel: 781.329.4700 www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Fax: 781.461.3113 ©2012 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. 10231-001 AD7988-1/AD7988-5 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 Analog Inputs.............................................................................. 16 Applications ....................................................................................... 1 Driver Amplifier Choice ........................................................... 16 General Description ......................................................................... 1 Voltage Reference Input ............................................................ 17 Typical Application Diagram .......................................................... 1 Power Supply ............................................................................... 17 Revision History ............................................................................... 2 Digital Interface .......................................................................... 17 Specifications ..................................................................................... 3 CS Mode, 3-Wire ........................................................................ 18 Timing Specifications .................................................................. 5 CS Mode 4-Wire ......................................................................... 19 Absolute Maximum Ratings ............................................................ 7 Chain Mode ................................................................................ 20 ESD Caution .................................................................................. 7 Applications Information .............................................................. 21 Pin Configurations and Function Descriptions ........................... 8 Interfacing to Blackfin® DSP ..................................................... 21 Terminology ...................................................................................... 9 Layout .......................................................................................... 21 Typical Performance Characteristics ........................................... 10 Evaluating the Performance of the AD7988-x ........................ 21 Theory of Operation ...................................................................... 14 Outline Dimensions ....................................................................... 22 Circuit Information .................................................................... 14 Ordering Guide .......................................................................... 23 Converter Operation .................................................................. 14 Typical Connection Diagram.................................................... 15 REVISION HISTORY 2/12—Rev. 0 to Rev. A Added LFCSP Thermal Impedance Values ................................... 7 Updated Outline Dimensions ....................................................... 23 Changes to Ordering Guide .......................................................... 23 2/12—Revision 0: Initial Version Rev. A | Page 2 of 24 Data Sheet AD7988-1/AD7988-5 SPECIFICATIONS VDD = 2.5 V, VIO = 2.3 V to 5.5 V, VREF = 5 V, TA = –40°C to +125°C, unless otherwise noted. Table 2. Parameter Test Conditions/Comments Min Typ Max Unit RESOLUTION 16 Bits ANALOG INPUT Voltage Range IN+ − IN− 0 V V REF Absolute Input Voltage IN+ −0.1 V + 0.1 V REF IN− −0.1 +0.1 V Analog Input CMRR fIN = 1 kHz 60 dB Leakage Current at 25°C Acquisition phase 1 nA Input Impedance See the Analog Inputs section ACCURACY No Missing Codes 16 Bits 1 Differential Linearity Error V = 5 V −0.9 ±0.4 +0.9 LSB REF 1 V = 2.5 V ±0.55 LSB REF 1 Integral Linearity Error V = 5 V −1.25 ±0.6 +1.25 LSB REF 1 VREF = 2.5 V ±0.65 LSB 1 Transition Noise VREF = 5 V 0.6 LSB 1 VREF = 2.5 V 1.0 LSB 2 1 Gain Error, T to T ±2 LSB MIN MAX Gain Error Temperature Drift ±0.35 ppm/°C 2 Zero Error, T to T −0.5 ±0.08 +0.5 mV MIN MAX Zero Temperature Drift 0.54 ppm/°C 1 Power Supply Sensitivity ±0.1 LSB VDD = 2.5 V ± 5% THROUGHPUT AD7988-1 Conversion Rate VIO ≥ 2.3 V up to 85°C, VIO ≥ 3.3 V above 85°C up to 0 100 kSPS 125°C Transient Response Full-scale step 500 ns AD7988-5 Conversion Rate VIO ≥ 2.3 V up to 85°C, VIO ≥ 3.3 V above 85°C up to 0 500 kSPS 125°C Transient Response Full-scale step 400 ns AC ACCURACY 3 Dynamic Range VREF = 5 V 92 dB 3 V = 2.5 V 87 dB REF 3 Oversampled Dynamic Range f = 10 kSPS 111 dB O 3 Signal-to-Noise Ratio, SNR f = 10 kHz, V = 5 V 90 91 dB IN REF 3 fIN = 10 kHz, VREF = 2.5 V 86.5 dB 3 Spurious-Free Dynamic Range, SFDR fIN = 10 kHz −110 dB 3 Total Harmonic Distortion, THD f = 10 kHz −114 dB IN 3 Signal-to-(Noise + Distortion), SINAD f = 10 kHz, V = 5 V 91.5 dB IN REF 3 f = 10 kHz, V = 2.5 V 87.0 dB IN REF 1 LSB means least significant bit. With the 5 V input range, 1 LSB is 76.3 µV. 2 See the Terminology section. These specifications include full temperature range variation, but not the error contribution from the external reference. 3 All specifications in dB are referred to a full-scale input FSR. Tested with an input signal at 0.5 dB below full scale, unless otherwise specified. Rev. A | Page 3 of 24 AD7988-1/AD7988-5 Data Sheet VDD = 2.5 V, VIO = 2.3 V to 5.5 V, V = 5 V, T = –40°C to +125°C, unless otherwise noted. REF A Table 3. Parameter Test Conditions/Comments Min Typ Max Unit REFERENCE Voltage Range 2.4 5.1 V Load Current V = 5 V 250 µA REF SAMPLING DYNAMICS −3 dB Input Bandwidth 10 MHz Aperture Delay VDD = 2.5 V 2.0 ns DIGITAL INPUTS Logic Levels V VIO > 3 V –0.3 0.3 × VIO V IL VIH VIO > 3 V 0.7 × VIO VIO + 0.3 V VIL VIO ≤ 3 V –0.3 0.1 × VIO V VIH VIO ≤ 3 V 0.9 × VIO VIO + 0.3 V I −1 +1 µA IL I −1 +1 µA IH DIGITAL OUTPUTS Data Format Serial 16 bits straight binary Pipeline Delay Conversion results available immediately after completed conversion VOL ISINK = 500 µA 0.4 V VOH ISOURCE = −500 µA VIO − 0.3 V POWER SUPPLIES VDD 2.375 2.5 2.625 V VIO Specified performance 2.3 5.5 V VIO Range 1.8 5.5 V 1, 2 Standby Current VDD and VIO = 2.5 V, 25°C 0.35 nA AD7988-1 Power Dissipation 10 kSPS throughput 70 µW 100 kSPS throughput 700 µW AD7988-5 Power Dissipation 500 kSPS throughput 3.5 mW Energy per Conversion 7.0 nJ/sample TEMPERATURE RANGE Specified Performance TMIN to TMAX −40 +125 °C 1 With all digital inputs forced to VIO or GND as required. 2 During the acquisition phase. Rev. A | Page 4 of 24 Data Sheet AD7988-1/AD7988-5 TIMING SPECIFICATIONS VDD = 2.37 V to 2.63 V, VIO = 3.3 V to 5.5 V, −40°C to +125°C unless otherwise stated. See Figure 2 and Figure 3 for load conditions. Table 4. Parameter Symbol Min Typ Max Unit AD7988-1 Throughput Rate 100 kHz Conversion Time: CNV Rising Edge to Data Available tCONV 9.5 μs Acquisition Time t 500 ns ACQ Time Between Conversions t 10 μs CYC AD7988-5 Throughput Rate 500 kHz Conversion Time: CNV Rising Edge to Data Available tCONV 1.6 μs Acquisition Time tACQ 400 ns Time Between Conversions t 2 μs CYC CNV Pulse Width (CS Mode) t 500 ns CNVH SCK Period ( Mode) t CS SCK VIO Above 4.5 V 10.5 ns VIO Above 3 V 12 ns VIO Above 2.7 V 13 ns VIO Above 2.3 V 15 ns SCK Period (Chain Mode) t SCK VIO Above 4.5 V 11.5 ns VIO Above 3 V 13 ns VIO Above 2.7 V 14 ns VIO Above 2.3 V 16 ns SCK Low Time t 4.5 ns SCKL SCK High Time t 4.5 ns SCKH SCK Falling Edge to Data Remains Valid tHSDO 3 ns SCK Falling Edge to Data Valid Delay tDSDO VIO Above 4.5 V 9.5 ns VIO Above 3 V 11 ns VIO Above 2.7 V 12 ns VIO Above 2.3 V 14 ns CNV or SDI Low to SDO D15 MSB Valid (CS Mode) tEN VIO Above 3 V 10 ns VIO Above 2.3V 15 ns CNV or SDI High or Last SCK Falling Edge to SDO High Impedance (CS Mode) t 20 ns DIS SDI Valid Setup Time from CNV Rising Edge t 5 ns SSDICNV SDI Valid Hold Time from CNV Rising Edge (CS Mode) tHSDICNV 2 ns SDI Valid Hold Time from CNV Rising Edge (Chain Mode) tHSDICNV 0 ns SCK Valid Setup Time from CNV Rising Edge (Chain Mode) tSSCKCNV 5 ns SCK Valid Hold Time from CNV Rising Edge (Chain Mode) t 5 ns HSCKCNV SDI Valid Setup Time from SCK Falling Edge (Chain Mode) t 2 ns SSDISCK SDI Valid Hold Time from SCK Falling Edge (Chain Mode) t 3 ns HSDISCK Rev. A | Page 5 of 24 AD7988-1/AD7988-5 Data Sheet 500µA I OL 1.4V TO SDO C L 20pF 500µA I OH Figure 2. Load Circuit for Digital Interface Timing 1 Y% VIO 1 X% VIO t t DELAY DELAY 2 2 V V IH IH 2 2 V V IL IL 1 FOR VIO ≤ 3.0V, X = 90 AND Y = 10; FOR VIO > 3.0V X = 70, AND Y = 30. 2 MINIMUM V AND MAXIMUM V USED. SEE DIGITAL INPUTS IH IL SPECIFICATIONS IN TABLE 3. Figure 3. Voltage Levels for Timing Rev. A | Page 6 of 24 10231-002 10231-003 Data Sheet AD7988-1/AD7988-5 ABSOLUTE MAXIMUM RATINGS Table 5. Parameter Rating Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress Analog Inputs 1 1 rating only; functional operation of the device at these or any IN+, IN− to GND −0.3 V to V + 0.3 V or ±130 mA REF other conditions above those indicated in the operational Supply Voltage section of this specification is not implied. Exposure to absolute REF, VIO to GND −0.3 V to +6 V maximum rating conditions for extended periods may affect VDD to GND −0.3 V to +3 V device reliability. VDD to VIO +3 V to −6 V Digital Inputs to GND −0.3 V to VIO + 0.3 V Digital Outputs to GND −0.3 V to VIO + 0.3 V ESD CAUTION Storage Temperature Range −65°C to +125°C Junction Temperature 150°C θJA Thermal Impedance 10-Lead MSOP 200°C/W 10-Lead LFCSP 80°C/W θJC Thermal Impedance 10-Lead MSOP 44°C/W 10-Lead LFCSP 15°C/W Reflow Soldering JEDEC Standard (J-STD-020) 1 See the Analog Inputs section. Rev. A | Page 7 of 24 AD7988-1/AD7988-5 Data Sheet PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS REF 1 10 VIO VDD 2 AD7988-1/ 9SDI AD7988-5 IN+ 3 8SCK REF 1 10 VIO TOP VIEW IN– 4 7SDO (Not to Scale) AD7988-1/ VDD 2 9 SDI AD7988-5 GND 5 6 CNV IN+ 3 8 SCK TOP VIEW IN– 4 7 SDO (Not to Scale) NOTES GND 5 6 CNV 1. THE EXPOSED PAD CAN BE CONNECTED TO GND. Figure 4. 10-Lead MSOP Pin Configuration Figure 5. 10-Lead LFCSP (QFN) Pin Configuration Table 6. Pin Function Descriptions 1 Pin No. Mnemonic Type Description 1 REF AI Reference Input Voltage. The V range is from 2.4 V to 5.1 V. It is referred to the GND pin. The GND pin REF should be decoupled closely to the REF pin with a 10 μF capacitor. 2 VDD P Power Supply. 3 IN+ AI Analog Input. It is referred to IN−. The voltage range, for example, the difference between IN+ and IN−, is 0 V to VREF. 4 IN− AI Analog Input Ground Sense. Connect to the analog ground plane or to a remote sense ground. 5 GND P Power Supply Ground. 6 CNV DI Convert Input. This input has multiple functions. On its leading edge, it initiates the conversions and selects the interface mode of the part: chain mode or CS mode. In CS mode, the SDO pin is enabled when CNV is low. In chain mode, the data should be read when CNV is high. 7 SDO DO Serial Data Output. The conversion result is output on this pin. It is synchronized to SCK. 8 SCK DI Serial Data Clock Input. When the part is selected, the conversion result is shifted out by this clock. 9 SDI DI Serial Data Input. This input provides multiple features. It selects the interface mode of the ADC as follows: Chain mode is selected if this pin is low during the CNV rising edge. In this mode, SDI is used as a data input to daisy-chain the conversion results of two or more ADCs onto a single SDO line. The digital data level on SDI is output on SDO with a delay of 16 SCK cycles. CS mode is selected if SDI is high during the CNV rising edge. In this mode, either SDI or CNV can enable the serial output signals when low. 10 VIO P Input/Output Interface Digital Power. Nominally at the same supply as the host interface (1.8 V, 2.5 V, 3 V, or 5 V). EP Exposed Pad. The exposed pad can be connected to GND. 1 AI = analog input, DI = digital input, DO = digital output, and P = power. Rev. A | Page 8 of 24 10231-004 10231-005 Data Sheet AD7988-1/AD7988-5 TERMINOLOGY Effective Resolution Integral Nonlinearity Error (INL) Effective resolution is calculated as INL refers to the deviation of each individual code from a line N Effective Resolution = log2(2 /RMS Input Noise) drawn from negative full scale through positive full scale. The point used as negative full scale occurs ½ LSB before the first and is expressed in bits. code transition. Positive full scale is defined as a level 1½ LSB Total Harmonic Distortion (THD) beyond the last code transition. The deviation is measured from THD is the ratio of the rms sum of the first five harmonic the middle of each code to the true straight line (see Figure 30). components to the rms value of a full-scale input signal and is Differential Nonlinearity Error (DNL) expressed in dB. In an ideal ADC, code transitions are 1 LSB apart. DNL is the Dynamic Range maximum deviation from this ideal value. It is often specified in Dynamic range is the ratio of the rms value of the full scale to terms of resolution for which no missing codes are guaranteed. the total rms noise measured with the inputs shorted together. The value for dynamic range is expressed in dB. It is measured Offset Error with a signal at −60 dBFS to include all noise sources and DNL The first transition should occur at a level ½ LSB above analog artifacts. ground (38.1 µV for the 0 V to 5 V range). The offset error is the deviation of the actual transition from that point. Signal-to-Noise Ratio (SNR) SNR is the ratio of the rms value of the actual input signal to the Gain Error rms sum of all other spectral components below the Nyquist The last transition (from 111 … 10 to 111 … 11) should frequency, excluding harmonics and dc. The value for SNR is occur for an analog voltage 1½ LSB below the nominal full expressed in dB. scale (4.999886 V for the 0 V to 5 V range). The gain error is the deviation of the actual level of the last transition from the Signal-to-(Noise + Distortion) Ratio (SINAD) ideal level after the offset is adjusted out. SINAD is the ratio of the rms value of the actual input signal to Spurious-Free Dynamic Range (SFDR) the rms sum of all other spectral components below the Nyquist frequency, including harmonics but excluding dc. The value for SFDR is the difference, in decibels (dB), between the rms SINAD is expressed in dB. amplitude of the input signal and the peak spurious signal. Aperture Delay Effective Number of Bits (ENOB) Aperture delay is the measure of the acquisition performance. It ENOB is a measurement of the resolution with a sine wave is the time between the rising edge of the CNV input and when input. It is related to SINAD by the following formula: the input signal is held for a conversion. ENOB = (SINAD − 1.76)/6.02 dB Transient Response and is expressed in bits. Transient response is the time required for the ADC to Noise-Free Code Resolution accurately acquire its input after a full-scale step function is Noise-free code resolution is the number of bits beyond which applied. it is impossible to distinctly resolve individual codes. It is calculated as N Noise-Free Code Resolution = log2(2 /Peak-to-Peak Noise) and is expressed in bits. Rev. A | Page 9 of 24 AD7988-1/AD7988-5 Data Sheet TYPICAL PERFORMANCE CHARACTERISTICS VDD = 2.5 V, VREF = 5.0 V, VIO = 3.3 V, unless otherwise noted. 0 0 f = 500kSPS f = 100kSPS S S f = 10kHz f = 10kHz –20 IN –20 IN SNR = 91.17dB SNR = 86.7dB THD = –113.63dB THD = –110.4dB –40 –40 SFDR = 110.30dB SFDR = 103.9dB SINAD = 91.15dB SINAD = 86.6dB –60 –60 –80 –80 –100 –100 –120 –120 –140 –140 –160 –160 –180 –180 0 50 100 150 200 250 0 10 20 30 40 50 FREQUENCY (kHz) FREQUENCY (kHz) Figure 6. AD7988-5 FFT Plot, V = 5 V Figure 9. AD7988-1 FFT Plot, V = 2.5 V REF REF 0 1.25 POSITIVE INL: +0.40 LSB f = 500kSPS S NEGATIVE INL: –0.35 LSB f = 10kHz 1.00 IN –20 SNR = 86.8dB THD = –111.4dB 0.75 –40 SFDR = 105.9dB SINAD = 86.8dB 0.50 –60 0.25 –80 0 –100 –0.25 –120 –0.50 –140 –0.75 –160 –1.00 –180 –1.25 0 16384 32768 49152 65536 0 50 100 150 200 250 FREQUENCY (kHz) CODE Figure 10. Integral Nonlinearity vs. Code, V = 5 V Figure 7. AD7988-5 FFT Plot, V = 2.5 V REF REF 0 1.25 POSITIVE INL: +0.45 LSB f = 100kSPS S NEGATIVE INL: –0.29 LSB 1.00 f = 10kHz –20 IN SNR = 91.09dB 0.75 THD = –113.12dB –40 SFDR = 110.30dB SINAD = 91.05dB 0.50 –60 0.25 –80 0 –100 –0.25 –120 –0.50 –140 –0.75 –160 –1.00 –1.25 –180 0 10 20 30 40 50 0 16384 32768 49152 65536 FREQUENCY (kHz) CODE Figure 11. Integral Nonlinearity vs. Code, VREF = 2.5 V Figure 8. AD7988-1 FFT Plot, VREF = 5 V Rev. A | Page 10 of 24 AMPLITUDE (dB of FULL SCALE) AMPLITUDE (dB of FULL SCALE) AMPLITUDE (dB of FULL SCALE) 10231-048 10231-047 10231-046 INL (LSB) INL (LSB) AMPLITUDE (dB of FULL SCALE) 10231-049 10231-011 10231-010 Data Sheet AD7988-1/AD7988-5 1.00 60k POSITIVE INL: +0.18 LSB NEGATIVE INL: –0.21 LSB 50970 0.75 50k 45198 0.50 40k 0.25 30k 0 –0.25 18848 20k –0.50 12424 10k –0.75 2290 1217 94 30 00 0 1 0 –1.00 0 7FFA 7FFB 7FFC 7FFD 7FFE 7FFF 8000 8001 8002 8003 8004 8005 8006 0 16384 32768 49152 65536 CODE IN HEX CODE Figure 15. Histogram of a DC Input at the Code Transition, VREF = 2.5 V Figure 12. Differential Nonlinearity vs. Code, V = 5 V REF 1.00 100 16 POSITIVE INL: +0.25 LSB SNR NEGATIVE INL: –0.22 LSB SINAD 0.75 ENOB 0.50 95 15 0.25 0 90 14 –0.25 –0.50 85 13 –0.75 80 12 –1.00 0 16384 32768 49152 65536 2.25 2.75 3.25 3.75 4.25 4.75 5.25 CODE REFERENCE VOLTAGE (V) Figure 13. Differential Nonlinearity vs. Code, V = 2.5 V Figure 16. SNR, SINAD, and ENOB vs. Reference Voltage REF 180k 60k 162595 53412 160k 50k 140k 120k 40k 37417 100k 31540 30k 80k 60k 20k 52720 42731 40k 10k 7285 20k 5807 1291 852 590 512 29 19 11 00 0 22 2 0 0 00 0 0 0 0 8003 8004 8005 8006 8007 8008 8009 800A 800B 800C 800D 800E 800F 7FFA 7FFB 7FFC 7FFD 7FFE 7FFF 8000 8001 8002 8003 8004 8005 8006 CODE IN HEX CODE IN HEX Figure 14. Histogram of a DC Input at the Code Center, VREF = 5 V Figure 17. Histogram of a DC Input at the Code Center, VREF = 2.5 V Rev. A | Page 11 of 24 DNL (LSB) DNL (LSB) COUNTS 10231-050 10231-013 10231-012 SNR, SINAD(dB) COUNTS COUNTS ENOB (Bits) 10231-015 10231-051 10231-016 AD7988-1/AD7988-5 Data Sheet 95 95 94 93 93 92 91 91 90 89 89 88 87 87 86 85 85 –55 –35 –15 5 25 45 65 85 105 125 –10 –9 –8 –7 –6 –5 –4 –3 –2 –1 0 TEMPERATURE (°C) INPUT LEVEL (dB OF FULL SCALE) Figure 18. SNR vs. Input Level Figure 21. SNR vs. Temperature –95 115 0.7 I VDD 0.6 –100 SFDR 110 0.5 –105 105 0.4 –110 100 0.3 I REF –115 THD 95 0.2 I VIO –120 90 0.1 –125 85 0 2.375 2.425 2.475 2.525 2.575 2.625 2.25 2.75 3.25 3.75 4.25 4.75 5.25 VDD VOLTAGE (V) REFERENCE VOLTAGE (V) Figure 19. THD, SFDR vs. Reference Voltage Figure 22. Operating Currents vs. Supply (AD7988-5) 100 0.14 I VDD 0.12 95 0.10 0.08 90 0.06 I REF 0.04 85 I VIO 0.02 0 80 2.375 2.425 2.475 2.525 2.575 2.625 10 100 1k FREQUENCY (kHz) VDD VOLTAGE (V) Figure 20. SINAD vs. Frequency Figure 23. Operating Currents vs. Supply (AD7988-1) Rev. A | Page 12 of 24 THD (dB) SINAD (dB) SNR (dB) 10231-018 10231-052 SFDR (dB) 10231-019 CURRENT (mA) CURRENT (mA) SNR (dB) 10231-023 10231-053 10231-024 Data Sheet AD7988-1/AD7988-5 –85 0.14 I VDD –90 0.12 –95 0.10 –100 008 –105 0.06 –110 I REF 0.04 –115 I VIO 0.02 –120 0 –125 10 100 1k –55 –35 –15 5 25 45 65 85 105 125 FREQUENCY (kHz) TEMPERATURE (°C) Figure 24. THD vs. Frequency Figure 27. Operating Currents vs. Temperature (AD7988-1) –110 8 7 –112 6 5 –114 4 –116 3 I + I VDD VIO 2 –118 1 –120 0 –55 –35 –15 5 25 45 65 85 105 125 –55 –35 –15 5 25 45 65 85 105 125 TEMPERATURE (°C) TEMPERATURE (°C) Figure 25. THD vs. Temperature Figure 28. Power-Down Currents vs. Temperature 0.7 I VDD 0.6 0.5 0.4 0.3 I REF 0.2 I VIO 0.1 0 –55 –35 –15 5 25 45 65 85 105 125 TEMPERATURE (°C) Figure 26. Operating Currents vs. Temperature (AD7988-5) Rev. A | Page 13 of 24 THD (dB) CURRENT (mA) THD (dB) 10231-027 10231-054 10231-026 CURRENT (mA) CURRENT (µA) 10231-029 10231-028 AD7988-1/AD7988-5 Data Sheet THEORY OF OPERATION IN+ MSB SWITCHES CONTROL LSB SW+ 32,768C 16,384C 4C 2C C C BUSY REF CONTROL COMP LOGIC GND OUTPUT CODE 32,768C 16,384C 4C 2C C C LSB SW– MSB CNV IN– Figure 29. ADC Simplified Schematic During the acquisition phase, terminals of the array tied to the CIRCUIT INFORMATION comparator’s input are connected to GND via SW+ and SW−. The AD7988-1/AD7988-5 devices are fast, low power, single- All independent switches are connected to the analog inputs. supply, precise 16-bit ADCs that use a successive approximation Therefore, the capacitor arrays are used as sampling capacitors architecture. and acquire the analog signal on the IN+ and IN− inputs. When The AD7988-1 is capable of converting 100,000 samples per the acquisition phase is completed and the CNV input goes high, a second (100 kSPS), whereas the AD7988-5 is capable of a conversion phase is initiated. When the conversion phase begins, throughput of 500 kSPS, and they power down between SW+ and SW− are opened first. The two capacitor arrays are then conversions. When operating at 10 kSPS, for example, the disconnected from the inputs and connected to the GND input. ADC consumes 70 µW typically, ideal for battery-powered Therefore, the differential voltage between the IN+ and IN− applications. inputs captured at the end of the acquisition phase are applied to the comparator inputs, causing the comparator to become The AD7988-x provides the user with on-chip track-and-hold unbalanced. By switching each element of the capacitor array and does not exhibit any pipeline delay or latency, making it between GND and REF, the comparator input varies by binary ideal for multiple multiplexed channel applications. weighted voltage steps (VREF/2, VREF/4 … VREF/65,536). The The AD7988-x can be interfaced to any 1.8 V to 5 V digital logic control logic toggles these switches, starting with the MSB, to family. It is housed in a 10-lead MSOP or a tiny 10-lead LFCSP bring the comparator back into a balanced condition. After the (QFN) that combines space savings and allows flexible completion of this process, the part returns to the acquisition phase configurations. and the control logic generates the ADC output code. CONVERTER OPERATION Because the AD7988-x has an on-board conversion clock, the The AD7988-x is a successive approximation ADC based on a serial clock, SCK, is not required for the conversion process. charge redistribution DAC. Figure 29 shows the simplified schematic of the ADC. The capacitive DAC consists of two identical arrays of 16 binary weighted capacitors, which are connected to the two comparator inputs. Rev. A | Page 14 of 24 10231-030 Data Sheet AD7988-1/AD7988-5 Transfer Functions Table 7. Output Codes and Ideal Input Voltages Analog Input The ideal transfer characteristic for the AD7988-x is shown in Figure 30 and Table 7. Description VREF = 5 V Digital Output Code (Hex) 1 FSR – 1 LSB 4.999924 V FFFF Midscale + 1 LSB 2.500076 V 8001 111 ... 111 Midscale 2.5 V 8000 111 ... 110 Midscale – 1 LSB 2.499924 V 7FFF 111 ... 101 –FSR + 1 LSB 76.3 µV 0001 2 –FSR 0 V 0000 1 This is also the code for an overranged analog input (VIN+ − VIN− above VREF − VGND). 2 This is also the code for an underranged analog input (V − V below V ). IN+ IN− GND TYPICAL CONNECTION DIAGRAM Figure 31 shows an example of the recommended connection 000 ... 010 diagram for the AD7988-x when multiple supplies are available. 000 ... 001 000 ... 000 –FSR –FSR + 1LSB +FSR – 1 LSB –FSR + 0.5LSB +FSR – 1.5 LSB ANALOG INPUT Figure 30. ADC Ideal Transfer Function 1 V+ REF 2.5V 2 10µF 100nF V+ 1.8V TO 5.5V 100nF 20Ω 0V TO V REF VDD VIO REF 3 IN+ SDI 2.7nF SCK AD7988-1/ V– 5 3- OR 4-WIRE INTERFACE AD7988-5 SDO 4 CNV IN– GND 1 SEE THE VOLTAGE REFERENCE INPUT SECTION FOR REFERENCE SELECTION. 2 C IS USUALLY A 10µF CERAMIC CAPACITOR (X5R). REF 3 SEE THE DRIVER AMPLIFIER CHOICE SECTION. 4 OPTIONAL FILTER. SEE THE ANALOG INPUTS SECTION. 5 SEE THE DIGITAL INTERFACE SECTION FOR THE MOST CONVENIENT INTERFACE MODE. Figure 31. Typical Application Diagram with Multiple Supplies Rev. A | Page 15 of 24 ADC CODE (STRAIGHT BINARY) 10231-031 10231-032 AD7988-1/AD7988-5 Data Sheet ANALOG INPUTS DRIVER AMPLIFIER CHOICE Figure 32 shows an equivalent circuit of the input structure of Although the AD7988-x is easy to drive, the driver amplifier the AD7988-x. needs to meet the following requirements: The two diodes, D1 and D2, provide ESD protection for the • The noise generated by the driver amplifier must be kept as analog inputs, IN+ and IN−. Care must be taken to ensure that low as possible to preserve the SNR and transition noise the analog input signal never exceeds the supply rails by more performance of the AD7988-x. The noise coming from the than 0.3 V, because this causes these diodes to become forward- driver is filtered by the AD7988-x analog input circuit’s biased and start conducting current. These diodes can handle a one-pole, low-pass filter made by R and C or by the IN IN forward-biased current of 130 mA maximum. For instance, external filter, if one is used. Because the typical noise of these conditions may eventually occur when the input buffer’s the AD7988-x is 47.3 µV rms, the SNR degradation due to supplies are different from VDD. In such a case (for example, an the amplifier is input buffer with a short circuit), the current limitation can be   used to protect the part.   47.3 REF   SNR = 20 log LOSS   π 2 2  47.3 + f (Ne )  N −3dB D1 2 C   IN R IN IN+ OR IN– where: C D2 PIN f is the input bandwidth in MHz of the AD7988-x –3dB GND (10 MHz) or the cutoff frequency of the input filter, if one is used. Figure 32. Equivalent Analog Input Circuit N is the noise gain of the amplifier (for example, 1 in buffer The analog input structure allows the sampling of the true configuration). differential signal between IN+ and IN−. By using these eN is the equivalent input noise voltage of the op amp, differential inputs, signals common to both inputs are rejected. in nV/√Hz. During the acquisition phase, the impedance of the analog • For ac applications, the driver should have a THD inputs (IN+ and IN−) can be modeled as a parallel combination of performance commensurate with the AD7988-x. Capacitor CPIN and the network formed by the series connection of • For multichannel multiplexed applications, the driver ampli- RIN and CIN. CPIN is primarily the pin capacitance. RIN is typically fier and the AD7988-x analog input circuit must settle for 400 Ω and is a lumped component made up of serial resistors a full-scale step onto the capacitor array at a 16-bit level and the on resistance of the switches. C is typically 30 pF and IN (0.0015%, 15 ppm). In the amplifier data sheet, settling at is mainly the ADC sampling capacitor. During the conversion 0.1% to 0.01% is more commonly specified. This may phase, when the switches are opened, the input impedance is differ significantly from the settling time at a 16-bit level limited to C . R and C make a one-pole, low-pass filter that PIN IN IN and should be verified prior to driver selection. reduces undesirable aliasing effects and limits the noise. Table 8. Recommended Driver Amplifiers When the source impedance of the driving circuit is low, the Amplifier Typical Application AD7988-x can be driven directly. Large source impedances ADA4841-1 Very low noise, small size, and low power significantly affect the ac performance, especially THD. The dc AD8021 Very low noise and high frequency performances are less sensitive to the input impedance. The AD8022 Low noise and high frequency maximum source impedance depends on the amount of THD OP184 Low power, low noise, and low frequency that can be tolerated. The THD degrades as a function of the AD8655 5 V single-supply, low noise source impedance and the maximum input frequency. AD8605, AD8615 5 V single-supply, low power Rev. A | Page 16 of 24 10231-033 Data Sheet AD7988-1/AD7988-5 To ensure optimum performance, VDD should be roughly half VOLTAGE REFERENCE INPUT of REF, the voltage reference input. For example, if REF is 5.0 V, The AD7988-x voltage reference input, REF, has a dynamic VDD should be set to 2.5 V (±5%). If REF = 2.5V, and VDD = input impedance and should therefore be driven by a low 2.5 V, performance is degraded as can be seen in Table 2. impedance source with efficient decoupling between the REF and GND pins, as explained in the Layout section. The AD7988-x powers down automatically at the end of each conversion phase. When REF is driven by a very low impedance source, for example, a reference buffer using the AD8031 or the AD8605, a ceramic DIGITAL INTERFACE chip capacitor is appropriate for optimum performance. Although the AD7988-x has a reduced number of pins, it offers If an unbuffered reference voltage is used, the decoupling value flexibility in its serial interface modes. depends on the reference used. For example, a 22 µF (X5R, The AD7988-x, when in CS mode, is compatible with SPI, QSPI™, 1206 size) ceramic chip capacitor is appropriate for optimum and digital hosts. This interface can use either a 3-wire or 4-wire performance using a low temperature drift ADR43x reference. interface. A 3-wire interface using the CNV, SCK, and SDO If desired, a reference-decoupling capacitor value as small as signals minimizes wiring connections and is useful, for 2.2 µF can be used with a minimal impact on performance, instance, in isolated applications. A 4-wire interface using the especially DNL. SDI, CNV, SCK, and SDO signals allows CNV, which initiates the conversions, to be independent of the readback timing Regardless, there is no need for an additional lower value ceramic (SDI). This is useful in low jitter sampling or simultaneous decoupling capacitor (for example, 100 nF) between the REF sampling applications. and GND pins. The AD7988-x, when in chain mode, provides a daisy-chain POWER SUPPLY feature using the SDI input for cascading multiple ADCs on a The AD7988-x uses two power supply pins: a core supply, VDD, single data line, similar to a shift register. and a digital input/output interface supply, VIO. VIO allows The mode in which the part operates depends on the SDI level direct interface with any logic between 1.8 V and 5.0 V. To when the CNV rising edge occurs. CS mode is selected if SDI is reduce the number of supplies needed, VIO and VDD can be high, and chain mode is selected if SDI is low. The SDI hold tied together. The AD7988-x is independent of power supply time is such that when SDI and CNV are connected together, sequencing between VIO and VDD. Additionally, it is very the chain mode is selected. insensitive to power supply variations over a wide frequency range, as shown in Figure 33. The user must time out the maximum conversion time prior to 80 readback. 75 70 65 60 55 1 10 100 1k FREQUENCY (kHz) Figure 33. PSRR vs. Frequency Rev. A | Page 17 of 24 PSRR (dB) 10231-034 AD7988-1/AD7988-5 Data Sheet When CNV goes low, the MSB is output onto SDO. The remaining CS MODE, 3-WIRE data bits are then clocked by subsequent SCK falling edges. The This mode is typically used when a single AD7988-x is data is valid on both SCK edges. Although the rising edge can connected to an SPI-compatible digital host. The connection be used to capture the data, a digital host using the SCK falling diagram is shown in Figure 34, and the corresponding timing is edge allows a faster reading rate, provided that it has an acceptable given in Figure 35. hold time. After the 16th SCK falling edge or when CNV goes With SDI tied to VIO, a rising edge on CNV initiates a conver- high, whichever is earlier, SDO returns to high impedance. sion, selects the CS mode, and forces SDO to high impedance. When the conversion is complete, the AD7988-x enters the acquisition phase and powers down. CONVERT DIGITAL HOST CNV VIO AD7988-1/ SDI SDO DATA IN AD7988-5 SCK CLK Figure 34. 3-Wire CS Mode Connection Diagram SDI = 1 t CYC t CNVH CNV t CONV t ACQ ACQUISITION CONVERSION ACQUISITION t SCK t SCKL SCK 1 2 3 14 15 16 t t HSDO SCKH t t t EN DIS DSDO SDO D15 D14 D13 D1 D0 Figure 35. 3-Wire CS Mode Serial Interface Timing (SDI High) Rev. A | Page 18 of 24 10231-035 10231-036 Data Sheet AD7988-1/AD7988-5 When the conversion is complete, the AD7988-x enters the CS MODE 4-WIRE acquisition phase and powers down. Each ADC result can This mode is typically used when multiple AD7988-x devices be read by bringing its SDI input low, which consequently are connected to an SPI-compatible digital host. outputs the MSB onto SDO. The remaining data bits are then A connection diagram example using two AD7988-x devices is clocked by subsequent SCK falling edges. The data is valid on shown in Figure 36, and the corresponding timing is given in both SCK edges. Although the rising edge can be used to capture Figure 37. the data, a digital host using the SCK falling edge allows a faster reading rate, provided that it has an acceptable hold time. After With SDI high, a rising edge on CNV initiates a conversion, the 16th SCK falling edge or when SDI goes high, whichever is selects the CS mode, and forces SDO to high impedance. In this earlier, SDO returns to high impedance and another AD7988-x mode, CNV must be held high during the conversion phase and can be read. the subsequent data readback (if SDI and CNV are low, SDO is driven low). Prior to the minimum conversion time, SDI can be used to select other SPI devices, such as analog multiplexers, but SDI must be returned high before the minimum conversion time elapses and then held high for the maximum conversion time. CS2 CS1 CONVERT CNV CNV DIGITAL HOST AD7988-1/ AD7988-1/ SDI SDO SDI SDO AD7988-5 AD7988-5 SCK SCK DATA IN CLK Figure 36. 4-Wire CS Mode Connection Diagram t CYC CNV t t CONV ACQ ACQUISITION CONVERSION ACQUISITION t SSDICNV SDI (CS1) t HSDICNV SDI (CS2) t SCK t SCKL SCK 1 2 3 14 15 16 17 18 30 31 32 t t HSDO SCKH t t t EN DSDO DIS SDO D15 D14 D13 D1 D0 D15 D14 D1 D0 CS Figure 37. 4-Wire Mode Serial Interface Timing Rev. A | Page 19 of 24 10231-037 10231-038 AD7988-1/AD7988-5 Data Sheet phase and the subsequent data readback. When the conversion CHAIN MODE is complete, the MSB is output onto SDO and the AD7988-x This mode can be used to daisy-chain multiple AD7988-x enters the acquisition phase and powers down. The remaining devices on a 3-wire serial interface. This feature is useful for data bits stored in the internal shift register are clocked by reducing component count and wiring connections, for example, subsequent SCK falling edges. For each ADC, SDI feeds the in isolated multiconverter applications or for systems with a input of the internal shift register and is clocked by the SCK limited interfacing capacity. Data readback is analogous to falling edge. Each ADC in the chain outputs its data MSB first, clocking a shift register. and 16 × N clocks are required to read back the N ADCs. The A connection diagram example using two AD7988-x devices is data is valid on both SCK edges. Although the rising edge can shown in Figure 38, and the corresponding timing is given in be used to capture the data, a digital host using the SCK falling Figure 39. edge allows a faster reading rate and, consequently, more When SDI and CNV are low, SDO is driven low. With SCK low, AD7988-x devices in the chain, provided that the digital host a rising edge on CNV initiates a conversion and selects the chain has an acceptable hold time. The maximum conversion rate mode. In this mode, CNV is held high during the conversion may be reduced due to the total readback time. CONVERT CNV CNV DIGITAL HOST AD7988-1/ AD7988-1/ SDI SDO SDI SDO DATA IN AD7988-5 AD7988-5 A B SCK SCK CLK Figure 38. Chain Mode Connection Diagram SDI = 0 A t CYC CNV t t CONV ACQ CONVERSION ACQUISITION ACQUISITION t SCK t SCKL t SSCKCNV SCK 1 2 3 14 15 16 17 18 30 31 32 t t t HSCKCNV SSDISCK SCKH t t HSDISCK EN SDO = SDI D 15 D 14 D 13 D 1 D 0 A B A A A A A t HSDO t DSDO D 15 D 14 D 13 D 1 D 0 D 15 D 14 D 1 D 0 SDO B B B B B B A A A A Figure 39. Chain Mode Serial Interface Timing Rev. A | Page 20 of 24 10231-039 10231-040 Data Sheet AD7988-1/AD7988-5 APPLICATIONS INFORMATION Using at least one ground plane is recommended. It can be INTERFACING TO BLACKFIN® DSP common or split between the digital and analog section. In the The AD7988-x can easily connect to a DSP SPI or SPORT. The latter case, join the planes underneath the AD7988-x devices. SPI configuration is straightforward, using the standard SPI The AD7988-x voltage reference input, REF, has a dynamic input interface as shown in Figure 40. impedance. Decouple REF with minimal parasitic inductances by placing the reference decoupling ceramic capacitor close to, SPI_CLK SCK but ideally right up against, the REF and GND pins and connect- AD7988-1/ BLACKFIN SPI_MISO SDO DSP AD7988-5 ing them with wide, low impedance traces. SPI_MOSI CNV Finally, decouple the power supplies of the AD7988-x, VDD and VIO, with ceramic capacitors, typically 100 nF, placed close to Figure 40. Typical Connection to Blackfin SPI Interface the AD7988-x and connected using short and wide traces to Similarly, the SPORT interface can be used to interface to this provide low impedance paths and to reduce the effect of glitches ADC. The SPORT interface has some benefits in that it can use on the power supply lines. direct memory access (DMA) and provides a lower jitter CNV An example of a layout following these rules is shown in Figure 42 signal generated from a hardware counter. and Figure 43. Some glue logic may be required between SPORT and the EVALUATING THE PERFORMANCE OF THE AD7988-x interface. The evaluation board for the AD7988-x AD7988-x interfaces directly to the SPORT of the Blackfin-based (ADSP- The evaluation board package for the AD7988-x (EVAL-AD7988- BF-527) SDP board. The configuration used for the SPORT 5SDZ) includes a fully assembled and tested evaluation board, interface requires the addition of some glue logic as shown in documentation, and software for controlling the board from a Figure 41. The SCK input to the ADC was gated off when CNV PC via the EVAL-SDP-CB1Z. was high to keep the SCK line static while converting the data, thereby ensuring the best integrity of the result. This approach AD7988-1/ uses an AND gate and a NOT gate for the SCK path. The other AD7988-5 logic gates used on the RSCLK and RFS paths are for delay matching purposes and may not be necessary where path lengths are short. This is one approach to using the SPORT interface for this ADC; there may be other solutions equal to this approach. VDRIVE DR SDO RSCLK TSCLK SCK BLACKFIN AD7988-1/ DSP AD7988-5 RFS TFS Figure 42. Example Layout of the AD7988-x (Top Layer) CNV Figure 41. Evaluation Board Connection to Blackfin Sport Interface LAYOUT Design the printed circuit board (PCB) that houses the AD7988-x so that the analog and digital sections are separated and confined to certain areas of the board. The pinout of the AD7988-x, with all the analog signals on the left side and all the digital signals on the right side, eases this task. Avoid running digital lines under the device because these couple noise onto the die, unless a ground plane under the AD7988-x is used as a shield. Fast switching signals, such as CNV or clocks, should never run near analog signal paths. Avoid crossover of digital and analog signals. Figure 43. Example Layout of the AD7988-x (Bottom Layer) Rev. A | Page 21 of 24 10231-041 10231-045 10231-044 10231-043 AD7988-1/AD7988-5 Data Sheet OUTLINE DIMENSIONS 3.10 3.00 2.90 10 6 5.15 3.10 4.90 3.00 4.65 1 2.90 5 PIN1 IDENTIFIER 0.50BSC 0.95 15°MAX 0.85 1.10MAX 0.75 0.70 0.15 0.23 6° 0.55 0.30 0.05 0.13 0° 0.40 0.15 COPLANARITY 0.10 COMPLIANTTOJEDECSTANDARDSMO-187-BA Figure 44.10-Lead Mini Small Outline Package [MSOP] (RM-10) Dimensions shown in millimeters 2.48 2.38 3.10 2.23 3.00SQ 0.50BSC 2.90 6 10 PIN1INDEX EXPOSED 1.74 AREA PAD 1.64 0.50 1.49 0.40 0.30 5 1 TOPVIEW BOTTOMVIEW FORPROPERCONNECTIONOF 0.80 THEEXPOSEDPAD,REFERTO 0.05MAX 0.75 THEPINCONFIGURATIONAND 0.02NOM 0.70 FUNCTIONDESCRIPTIONS SECTIONOFTHISDATASHEET. SEATING 0.30 PLANE 0.20REF 0.25 0.20 Figure 45. 10-Lead Lead Frame Chip Scale Package [QFN (LFCSP_WD)] 3 mm × 3 mm Body, Very Very Thin, Dual Lead (CP-10-9) Dimensions shown in millimeters Rev. A | Page 22 of 24 PIN1 INDICATOR (R0.15) 091709-A 121009-A Data Sheet AD7988-1/AD7988-5 ORDERING GUIDE Integral Temperature Ordering Package 1 Model Notes Nonlinearity Range Quantity Package Description Option Branding AD7988-1BRMZ ±1.25 LSB max −40°C to +125°C Tube, 50 10-Lead MSOP RM-10 C7E AD7988-1BRMZ-RL7 ±1.25 LSB max −40°C to +125°C Reel, 1,000 10-Lead MSOP RM-10 C7E AD7988-1BCPZ-RL ±1.25 LSB max −40°C to +125°C Reel, 5,000 10-Lead QFN (LFCSP_WD) CP-10-9 C7X AD7988-1BCPZ-RL7 ±1.25 LSB max −40°C to +125°C Reel, 1,500 10-Lead QFN (LFCSP_WD) CP-10-9 C7X AD7988-5BRMZ ±1.25 LSB max −40°C to +125°C Tube, 50 10-Lead MSOP RM-10 C7Q AD7988-5BRMZ-RL7 ±1.25 LSB max −40°C to +125°C Reel, 1,000 10-Lead MSOP RM-10 C7Q AD7988-5BCPZ-RL ±1.25 LSB max −40°C to +125°C Reel, 5,000 10-Lead QFN (LFCSP_WD) CP-10-9 C7Y AD7988-5BCPZ-RL7 ±1.25 LSB max −40°C to +125°C Reel, 1,500 10-Lead QFN (LFCSP_WD) CP-10-9 C7Y 2 EVAL-AD7988-5SDZ Evaluation Board with AD7988-5 Populated; Use for Evaluation of Both AD7988-1 and AD7988-5. 3 EVAL-SDP-CB1Z System Demonstration Board, Used as a Controller Board for Data Transfer via USB Interface to PC. 1 Z = RoHS Compliant Part. 2 This board can be used as a standalone evaluation board or in conjunction with the EVAL-SDZ-CB1Z for evaluation/demonstration purposes. 3 This board allows a PC to control and communicate with all Analog Devices evaluation boards ending in the SD designator. Rev. A | Page 23 of 24 AD7988-1/AD7988-5 Data Sheet NOTES ©2012 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D10231-0-2/12(A) Rev. A | Page 24 of 24

Frequently asked questions

What makes Elite.Parts unique?

chervon down
At GID Industrial (Elite.Parts' parent company), we specialize in procuring industrial parts. We know where to find the rare and obsolete equipment that our customers need in order to get back to business. There are other companies who claim to do what we do, but we're confident that our commitment to quality and value is unparalleled in our field.

What kind of warranty will the AD7988-1 have?

chervon down
Warranties differ by part and by which suppliers we use to procure it for you. Sometimes, a part will be sold as-is and without a warranty. Our specialty, single board computers, tend to receive a one-year warranty.

Which carriers does Elite.Parts work with?

chervon down
Elite.Parts can ship via FedEx, UPS, DHL, and USPS. We have accounts with each of them and generally ship using one of those, but we can also ship using your account if you would prefer. However, we can use other carriers if it will be more convenient for you.

Will Elite.Parts sell to me even though I live outside the USA?

chervon down
Absolutely! We are happy to serve customers regardless of location. We work with international clients all the time, and we are familiar with shipping to destinations all across the globe.

I have a preferred payment method. Will Elite.Parts accept it?

chervon down
All major credit cards are accepted: Visa, MasterCard, Discover, and American Express. We will also accept payment made with wire transfer or PayPal. Checks will only be accepted from customers in the USA. Terms may available for larger orders, upon approval.

Why buy from GID?

quality

Quality

We are industry veterans who take pride in our work

protection

Protection

Avoid the dangers of risky trading in the gray market

access

Access

Our network of suppliers is ready and at your disposal

savings

Savings

Maintain legacy systems to prevent costly downtime

speed

Speed

Time is of the essence, and we are respectful of yours

What they say about us

FANTASTIC RESOURCE

star star star star star

One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!

Bucher Emhart Glass

EXCELLENT SERVICE

star star star star star

With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.

Fuji

HARD TO FIND A BETTER PROVIDER

star star star star star

Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.

Applied Materials

CONSISTENTLY DELIVERS QUALITY SOLUTIONS

star star star star star

Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.

Nidec Vamco

TERRIFIC RESOURCE

star star star star star

This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.

Trican Well Service

GO TO SOURCE

star star star star star

When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.

ConAgra Foods

Related Products

ANALOG DEVICE# A5E1032

SOCKET FOR MODEL AD210 IC

TRANSFORMER CURRENT 60.0 AMP

SOCKET FOR MODEL 1B22 IC

product

Analog Devices AD7291 12-Bit Low power 8-Channel Successive Approximation Analog-to-Digital Converte...