ANALOG DEVICES AD7829-1
Description
Analog Devices AD7829-1 High Speed, 8-Channel Microprocessor-compatible, 8-bit analog-to-digital converter
Part Number
AD7829-1
Price
Request Quote
Manufacturer
ANALOG DEVICES
Lead Time
Request Quote
Category
PRODUCTS - A
Features
- 8-bit half-flash ADC with 420 ns conversion time
- Automatic power-down at the end of conversion
- Available with input offset adjust
- Eight single-ended analog input channels
- Flexible parallel interface with EOC pulse to allow stand-alone operation
- Input ranges: 0 V to 2 V p-p, VDD = 3 V ± 10%; 0 V to 2.5 V p-p, VDD = 5 V ± 10%
- On-chip reference (2.5 V)
- On-chip track-and-hold
- SNR performance given for input frequencies up to10 MHz
- Wide operating supply range: 3 V ± 10% and 5 V ± 10%
Datasheet
Extracted Text
3 V/5 V, 2 MSPS, 8-Bit, 8-Channel ADC AD7829-1 FEATURES FUNCTIONAL BLOCK DIAGRAM V 8-bit half-flash ADC with 420 ns conversion time DD CONVST EOC A0 A1 A2 Eight single-ended analog input channels Available with input offset adjust CONTROL COMP LOGIC 2.5V On-chip track-and-hold REF SNR performance given for input frequencies V IN1 up to10 MHz BUF V V REF IN/OUT IN2 On-chip reference (2.5 V) V IN3 8-BIT INPUT V Automatic power-down at the end of conversion IN4 HALF T/H MUX V FLASH IN5 Wide operating supply range ADC DB7 V PARALLEL IN6 PORT DB0 V 3 V ± 10% and 5 V ± 10% IN7 V IN8 Input ranges 0 V to 2 V p-p, V = 3 V ± 10% DD V MID AGND DGND CS RD 0 V to 2.5 V p-p, VDD = 5 V ± 10% Figure 1. EOC Flexible parallel interface with pulse to allow stand-alone operation APPLICATIONS Data acquisition systems, DSP front ends Disk drives Mobile communication systems, subsampling applications GENERAL DESCRIPTION The AD7829-1 is a high speed 8-channel, microprocessor- The AD7829-1 is available in a 28-lead, wide body, small outline compatible, 8-bit analog-to-digital converter with a maximum IC (SOIC_W) and a 28-lead thin shrink small outline package throughput of 2 MSPS. The AD7829-1 contains an on-chip (TSSOP). reference of 2.5 V (2% tolerance); a track-and-hold amplifier; PRODUCT HIGHLIGHTS a 420 ns, 8-bit half-flash ADC; and a high speed parallel 1. Fast Conversion Time. The AD7829-1 has a conversion interface. The converter can operate from a single 3 V ± 10% time of 420 ns. Faster conversion times maximize the DSP and 5 V ± 10% supply. processing time in a real-time system. The AD7829-1 combines the convert start and power-down 2. Analog Input Span Adjustment. The V pin allows the MID functions at one pin, that is, the CONVST pin. This allows a user to offset the input span. This feature can reduce the unique automatic power-down at the end of a conversion to be requirements of single-supply op amps and take into CONVST implemented. The logic level on the pin is sampled account any system offsets. EOC after the end of a conversion when an (end of conversion) 3. FPBW (Full Power Bandwidth) of Track-and-Hold. The signal goes high, and if it is logic low at that point, the ADC is track-and-hold amplifier has excellent high frequency powered down. The parallel interface is designed to allow easy performance. The AD7829-1 is capable of converting full- interfacing to microprocessors and DSPs. Using only address scale input signals up to a frequency of 10 MHz, making decoding logic, the parts are easily mapped into the microprocessor the parts ideally suited to subsampling applications. address space. 4. Channel Selection. Channel selection is made without the EOC The pulse allows the ADCs to be used in a stand-alone necessity of writing to the part. manner (see the Parallel Interface section). Rev. 0 Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. rights of third parties that may result from its use. Specifications subject to change without notice. No Tel: 781.329.4700 www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Fax: 781.461.3113 ©2006 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. 06179-001 AD7829-1 TABLE OF CONTENTS Features .............................................................................................. 1 Typical Connection Diagram ................................................... 10 Applications....................................................................................... 1 ADC Transfer Function............................................................. 11 General Description ......................................................................... 1 Analog Input ............................................................................... 11 Functional Block Diagram .............................................................. 1 Power-Up Times......................................................................... 14 Product Highlights ........................................................................... 1 Power vs. Throughput................................................................ 14 Revision History ............................................................................... 2 Operating Modes........................................................................ 15 Specifications..................................................................................... 3 Parallel Interface......................................................................... 17 Timing Characteristics ................................................................ 5 Microprocessor Interfacing........................................................... 18 Timing Diagram ........................................................................... 5 AD7829-1 to 8051 ...................................................................... 18 Absolute Maximum Ratings............................................................ 6 AD7829-1 to PIC16C6x/PIC16C7x......................................... 18 ESD Caution.................................................................................. 6 AD7829-1 to ADSP-21xx .......................................................... 18 Pin Configuration and Function Descriptions............................. 7 Interfacing Multiplexer Address Inputs .................................. 18 Terminology ...................................................................................... 8 Outline Dimensions....................................................................... 20 Circuit Information........................................................................ 10 Ordering Guide .......................................................................... 20 Circuit Description..................................................................... 10 REVISION HISTORY 7/06—Revision 0: Initial Version Rev. 0 | Page 2 of 20 AD7829-1 SPECIFICATIONS VDD = 3 V ± 10%, VDD = 5 V ± 10%, GND = 0 V, VREF IN/OUT = 2.5 V. All specifications −40°C to +85°C, unless otherwise noted. Table 1. Parameter Version B Unit Test Conditions/Comments DYNAMIC PERFORMANCE f = 30 kHz, f = 2 MHz IN SAMPLE 1 Signal to (Noise + Distortion) Ratio 48 dB min 1 Total Harmonic Distortion −55 dB max 1 Peak Harmonic or Spurious Noise −55 dB max 1 Intermodulation Distortion fa = 27.3 kHz, fb = 28.3 kHz 2nd Order Terms −65 dB typ 3rd Order Terms −65 dB typ 1 Channel-to-Channel Isolation −70 dB typ f = 20 kHz IN DC ACCURACY Resolution 8 Bits Minimum Resolution for Which 8 Bits No Missing Codes Are Guaranteed 1 Integral Nonlinearity (INL) ±0.75 LSB max 1 Differential Nonlinearity (DNL) ±0.75 LSB max 1 Gain Error ±2 LSB max 1 Gain Error Match ±0.1 LSB typ 1 Offset Error ±1 LSB max 1 Offset Error Match ±0.1 LSB typ 2 ANALOG INPUTS See Analog Input section VDD = 5 V ± 10% Input voltage span = 2.5 V VIN1 to VIN8 Input Voltage VDD V max 0 V min V Input Voltage V − 1.25 V max Default V = 1.25 V MID DD MID 1.25 V min VDD = 3 V ± 10% Input voltage span = 2 V VIN1 to VIN8 Input Voltage VDD V max 0 V min V Input Voltage V − 1 V max Default V = 1 V MID DD MID 1 V min V Input Leakage Current ±1 μA max IN VIN Input Capacitance 15 pF max VMID Input Impedance 6 kΩ typ REFERENCE INPUT VREF IN/OUT Input Voltage Range 2.55 V max 2.5 V + 2% 2.45 V min 2.5 V − 2% Input Current 1 μA typ 100 μA max ON-CHIP REFERENCE Nominal 2.5 V Reference Error ±50 mV max Temperature Coefficient 50 ppm/°C typ LOGIC INPUTS Input High Voltage, V 2.4 V min V = 5 V ± 10% INH DD Input Low Voltage, V 0.8 V max V = 5 V ± 10% INL DD Input High Voltage, V 2 V min V = 3 V ± 10% INH DD Input Low Voltage, VINL 0.4 V max VDD = 3 V ± 10% Input Current, IIN ±1 μA max Typically 10 nA, VIN = 0 V to VDD Input Capacitance, CIN 10 pF max Rev. 0 | Page 3 of 20 AD7829-1 Parameter Version B Unit Test Conditions/Comments LOGIC OUTPUTS Output High Voltage, VOH ISOURCE = 200 μA 4 V min VDD = 5 V ± 10% 2.4 V min V = 3 V ± 10% DD Output Low Voltage, V I = 200 μA OL SINK 0.4 V max V = 5 V ± 10% DD 0.2 V max VDD = 3 V ± 10% High Impedance Leakage Current ±1 μA max High Impedance Capacitance 10 pF max CONVERSION RATE Track/Hold Acquisition Time 200 ns max See Circuit Description section Conversion Time 420 ns max POWER SUPPLY REJECTION VDD ± 10% ±1 LSB max POWER REQUIREMENTS VDD 4.5 V min 5 V ± 10%; for specified performance 5.5 V max V 2.7 V min 3 V ± 10%; for specified performance DD 3.3 V max IDD Normal Operation 12 mA max 8 mA typically Power-Down 5 μA max Logic inputs = 0 V or VDD 0.2 μA typ Power Dissipation V = 3 V DD Normal Operation 36 mW max Typically 24 mW Power-Down 200 kSPS 9.58 mW typ 500 kSPS 23.94 mW typ 1 See the Terminology section of this data sheet. 2 Refer to the Analog Input section for an explanation of the analog input(s). Rev. 0 | Page 4 of 20 AD7829-1 TIMING CHARACTERISTICS VREF IN/OUT = 2.5 V. All specifications −40°C to +85°C, unless otherwise noted. Table 2. 1, 2 Parameter 5 V ± 10% 3 V ± 10% Unit Description t 420 420 ns max Conversion time 1 t2 20 20 ns min Minimum CONVST pulse width t3 30 30 ns min Minimum time between the rising edge of RD and the next falling edge of convert start t4 110 110 ns max EOC pulse width 70 70 ns min t 10 10 ns max RD rising edge to EOC pulse high 5 t6 0 0 ns min CS to RD setup time t7 0 0 ns min CS to RD hold time t8 30 30 ns min Minimum RD pulse width 3 t 10 20 ns max Data access time after RD low 9 4 t 5 5 ns min Bus relinquish time after RD high 10 20 20 ns max t11 10 10 ns min Address setup time before the falling edge of RD t12 15 15 ns min Address hold time after the falling edge of RD t13 200 200 ns min Minimum time between new channel selection and convert start t 25 25 μs typ Power-up time from the rising edge of CONVST using on-chip reference POWER UP t 1 1 μs max Power-up time from the rising edge of CONVST using external 2.5 V reference POWER UP 1 Sample tested to ensure compliance. 2 See Figure 21, Figure 22, and Figure 23. 3 Measured with the load circuit of Figure 2 and defined as the time required for an output to cross 0.8 V or 2.4 V with V = 5 V ± 10%, and the time required for an DD output to cross 0.4 V or 2.0 V with VDD = 3 V ± 10%. 4 Derived from the measured time taken by the data outputs to change 0.5 V when loaded with the circuit of Figure 2. The measured number is then extrapolated back to remove the effects of charging or discharging the 50 pF capacitor. This means that the time, t10, quoted in the timing characteristics is the true bus relinquish time of the part and, as such, is independent of external bus loading capacitances. TIMING DIAGRAM 200µA I OL TO OUTPUT 2.1V PIN C L 50pF 200µA I OH Figure 2. Load Circuit for Access Time and Bus Relinquish Time Rev. 0 | Page 5 of 20 06179-002 AD7829-1 ABSOLUTE MAXIMUM RATINGS TA = 25°C, unless otherwise noted. Table 3. Stresses above those listed under Absolute Maximum Ratings Parameter Rating may cause permanent damage to the device. This is a stress V to AGND −0.3 V to +7 V rating only; functional operation of the device at these or any DD V to DGND −0.3 V to +7 V other conditions above those indicated in the operational DD section of this specification is not implied. Exposure to absolute Analog Input Voltage to AGND maximum rating conditions for extended periods may affect VIN1 to VIN8 −0.3 V to VDD + 0.3 V Reference Input Voltage to AGND −0.3 V to VDD + 0.3 V device reliability. V Input Voltage to AGND −0.3 V to V + 0.3 V MID DD Digital Input Voltage to DGND −0.3 V to V + 0.3 V DD Digital Output Voltage to DGND −0.3 V to V + 0.3 V DD Operating Temperature Range Industrial (B Version) −40°C to +85°C Storage Temperature Range −65°C to +150°C Junction Temperature 150°C SOIC Package, Power Dissipation 450 mW θJA Thermal Impedance 75°C/W Lead Temperature, Soldering Vapor Phase (60 sec) 215°C Infrared (15 sec) 220°C TSSOP Package, Power Dissipation 450 mW θ Thermal Impedance 128°C/W JA Lead Temperature, Soldering Vapor Phase (60 sec) 215°C Infrared (15 sec) 220°C ESD 1 kV ESD CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although this product features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. Rev. 0 | Page 6 of 20 AD7829-1 PIN CONFIGURATION AND FUNCTION DESCRIPTIONS DB2 1 28 DB3 DB1 2 27 DB4 DB0 3 26 DB5 CONVST 4 25 DB6 CS 5 24 DB7 AD7829-1 RD 6 23 AGND TOP VIEW DGND 7 22 V DD (Not to Scale) EOC 8 21 V REF IN/OUT A2 9 20 V MID A1 10 19 V IN1 A0 11 18 V IN2 V 12 17 V IN8 IN3 V 13 16 V IN7 IN4 V 14 15 V IN6 IN5 Figure 3. Pin Configuration Table 4. Pin Function Descriptions Pin No. Mnemonic Description 12 to 19 V to V Analog Input Channels. The AD7829-1 has eight analog input channels. The inputs have an input span of 2.5 V IN8 IN1 and 2 V, depending on the supply voltage (VDD). This span can be centered anywhere in the range AGND to VDD using the VMID pin. The default input range (VMID unconnected) is AGND to 2 V (VDD = 3 V ± 10%) or AGND to 2.5 V (VDD = 5 V ± 10%). See the Analog Input section of the data sheet for more information. 22 V Positive Supply Voltage, 3 V ± 10% and 5 V ± 10%. DD 23 AGND Analog Ground. Ground reference for track/hold, comparators, reference circuit, and multiplexer. 7 DGND Digital Ground. Ground reference for digital circuitry. 4 CONVST Logic Input Signal. The convert start signal initiates an 8-bit analog-to-digital conversion on the falling edge of this signal. The falling edge of this signal places the track/hold in hold mode. The track/hold goes into track mode again 120 ns after the start of a conversion. The state of the CONVST signal is checked at the end of a conversion. If it is logic low, the AD7829-1 powers down (see the Operating Modes section). 8 EOC Logic Output. The end of conversion signal indicates when a conversion has finished. The signal can be used to interrupt a microcontroller when a conversion has finished or latch data into a gate array (see the Parallel Interface section). 5 CS Logic Input Signal. The chip select signal is used to enable the parallel port of the AD7829. This is necessary if the ADC is sharing a common data bus with another device. 6 RD Logic Input Signal. The read signal is used to take the output buffers out of their high impedance state and drive data onto the data bus. The signal is internally gated with the CS signal. Both RD and CS must be logic low to enable the data bus. 9 to 11 A2 to A0 Channel Address Inputs. The address of the next multiplexer channel must be present on these inputs when the RD signal goes low. 1 to 3, DB2 to DB0, Data Output Lines. They are normally held in a high impedance state. Data is driven onto the data bus when 24 to 28 DB7 to DB3 both RD and CS go active low. 21 V REF IN/OUT Analog Input and Output. An external reference can be connected to the AD7829-1 at this pin. The on-chip reference is also available at this pin. When using the internal reference, this pin can be left unconnected or, in some cases, it can be decoupled to AGND with a 0.1 μF capacitor. 20 VMID The V pin, if connected, is used to center the analog input span anywhere in the range of AGND to V MID DD (see the Analog Input section). Rev. 0 | Page 7 of 20 06179-003 AD7829-1 TERMINOLOGY As a result, the second and third order terms are specified Signal-to-(Noise + Distortion) Ratio separately. The calculation of the intermodulation distortion is The measured ratio of signal-to-(noise + distortion) at the as per the THD specification, where it is the ratio of the rms output of the A/D converter. The signal is the rms amplitude of sum of the individual distortion products to the rms amplitude the fundamental. Noise is the rms sum of all nonfundamental of the fundamental expressed in decibels (dB). signals up to half the sampling frequency (f /2), excluding dc. S The ratio is dependent upon the number of quantization levels Channel-to-Channel Isolation in the digitization process; the more levels, the smaller the A measure of the level of crosstalk between channels. It is quantization noise. The theoretical signal-to-(noise + measured by applying a full-scale 20 kHz sine wave signal to distortion) ratio for an ideal N-bit converter with a sine wave one input channel and determining how much that signal is input is given by attenuated in each of the other channels. The figure given is Signal-to-(Noise + Distortion) = (6.02N + 1.76) dB the worst case across all eight channels of the AD7829-1. Thus, for an 8-bit converter, this is 50 dB. Relative Accuracy or Endpoint Nonlinearity The maximum deviation from a straight line passing through Total Harmonic Distortion (THD) the endpoints of the ADC transfer function. The ratio of the rms sum of harmonics to the fundamental. For the AD7829-1 it is defined as Differential Nonlinearity 2 2 2 2 2 The difference between the measured and the ideal 1 LSB V +V +V +V +V 2 3 4 5 6 THD (dB)= 20 log change between any two adjacent codes in the ADC. V 1 Offset Error where V is the rms amplitude of the fundamental, and V , V , 1 2 3 The deviation of the 128th code transition (01111111) to V , V , and V are the rms amplitudes of the second through the 4 5 6 (10000000) from the ideal, that is, VMID. sixth harmonics. Offset Error Match Peak Harmonic or Spurious Noise The difference in offset error between any two channels. The ratio of the rms value of the next largest component in the ADC output spectrum (up to fS/2 and excluding dc) to the rms Zero-Scale Error value of the fundamental. Normally, the value of this specifica- The deviation of the first code transition (00000000) to tion is determined by the largest harmonic in the spectrum, (00000001) from the ideal; that is, VMID − 1.25 V + 1 LSB (VDD = but for parts where the harmonics are buried in the noise floor, 5 V ± 10%), or VMID − 1.0 V + 1 LSB (VDD = 3 V ± 10%). it will be a noise peak. Full-Scale Error Intermodulation Distortion The deviation of the last code transition (11111110) to With inputs consisting of sine waves at two frequencies, fa and (11111111) from the ideal; that is, V + 1.25 V − 1 LSB (V = MID DD fb, any active device with nonlinearities creates distortion 5 V ± 10%), or V + 1.0 V − 1 LSB (V = 3 V ± 10%). MID DD products at sum and difference frequencies of mfa ± nfb, where m, n = 0, 1, 2, 3… . Intermodulation terms are those for which Gain Error neither m nor n is equal to zero. For example, the second order The deviation of the last code transition (1111 . . . 110) to terms include (fa + fb) and (fa − fb), while the third order terms (1111 . . . 111) from the ideal; that is, VREF − 1 LSB, after the include (2fa + fb), (2fa − fb), (fa + 2fb), and (fa − 2fb). The offset error has been adjusted out. AD7829-1 is tested using the CCIF standard, where two input Gain Error Match frequencies near the top end of the input bandwidth are used. The difference in gain error between any two channels. In this case, the second and third order terms are of different significance. The second order terms are usually distanced in frequency from the original sine waves, while the third order terms are usually at a frequency close to the input frequencies. Rev. 0 | Page 8 of 20 AD7829-1 It means that the user must wait for the duration of the Track/Hold Acquisition Time track/hold acquisition time after a channel change/step input The time required for the output of the track/hold amplifier to change to V before starting another conversion, to ensure that IN reach its final value, within ±1/2 LSB, after the point at which the part operates to specification. the track/hold returns to track mode. This happens approxi- mately 120 ns after the falling edge of CONVST. PSR (Power Supply Rejection) Variations in power supply affect the full-scale transition It also applies to situations where a change in the selected input but not the converter’s linearity. Power supply rejection is the channel takes place or where there is a step input change on the maximum change in the full-scale transition point due to a input voltage applied to the selected VIN input of the AD7829-1. change in power supply voltage from the nominal value. Rev. 0 | Page 9 of 20 AD7829-1 CIRCUIT INFORMATION CIRCUIT DESCRIPTION REFERENCE The AD7829-1 consists of a track-and-hold amplifier followed by a half-flash analog-to-digital converter. These devices use a half-flash conversion technique where one 4-bit flash ADC is R16 15 D7 used to achieve an 8-bit result. The 4-bit flash ADC contains a D6 sampling capacitor followed by 15 comparators that compare R15 SW2 A the unknown input to a reference ladder to achieve a 4-bit result. D5 T/H 1 14 V IN SAMPLING This first flash, that is, coarse conversion, provides the four B D4 CAPACITOR HOLD MSBs. For a full 8-bit reading to be realized, a second flash, D3 R14 13 that is, a fine conversion, must be performed to provide the four D2 R13 LSBs. The 8-bit word is then placed on the data output bus. D1 D0 Figure 4 and Figure 5 show simplified schematics of the ADC. 1 When the ADC starts a conversion, the track-and-hold goes R1 into hold mode and holds the analog input for 120 ns. This is TIMING AND CONTROL the acquisition phase as shown in Figure 4, when Switch 2 is in LOGIC Position A. At the point when the track-and-hold returns to its track mode, this signal is sampled by the sampling capacitor as Figure 5. ADC Conversion Phase Switch 2 moves into Position B. The first flash occurs at this 120ns instant and is then followed by the second flash. Typically, the TRACK TRACK HOLD HOLD first flash is complete after 100 ns, that is, at 220 ns, while the CONVST t 2 end of the second flash and, hence, the 8-bit conversion result, t 1 EOC is available at 330 ns (minimum). The maximum conversion time is 420 ns. As shown in Figure 6, the track-and-hold returns CS to track mode after 120 ns and starts the next acquisition before t 3 the end of the current conversion. Figure 8 shows the ADC RD transfer function. VALID DB0 TO DB7 DATA REFERENCE Figure 6. Track-and-Hold Timing TYPICAL CONNECTION DIAGRAM Figure 7 shows a typical connection diagram for the AD7829-1. R16 15 D7 The AGND and DGND are connected together at the device for D6 good noise suppression. The parallel interface is implemented R15 SW2 A D5 EOC 14 using an 8-bit data bus. The end of conversion signal ( ) idles V T/H 1 IN SAMPLING B D4 CONVST high, the falling edge of initiates a conversion, and at CAPACITOR HOLD D3 EOC the end of conversion the falling edge of is used to initiate R14 13 D2 an interrupt service routine (ISR) on a microprocessor (see the R13 Parallel Interface section). VREF IN/OUT and VMID are connected to a D1 voltage source, such as the AD780, while VDD is connected to a D0 1 voltage source that can vary from 4.5 V to 5.5 V (see Table 5 in R1 the Analog Input section). When VDD is first connected, the TIMING AND AD7829-1 powers up in a low current mode, that is, power-down. CONTROL LOGIC CONVST Ensure that the line is not floating when VDD is applied, because this can put the AD7829-1 into an unknown state. Figure 4. ADC Acquisition Phase Rev. 0 | Page 10 of 20 DECODE LOGIC OUTPUT REGISTER OUTPUT DRIVERS 06179-005 DECODE LOGIC OUTPUT REGISTER OUTPUT DRIVERS 06179-007 06179-006 AD7829-1 CONVST A suggestion is to tie to VDD or DGND through a ANALOG INPUT CONVST pull-up or pull-down resistor. A rising edge on the The AD7829-1 has eight input channels. Each input channel has pin causes the AD7829-1 to fully power up. For applications an input span of 2.5 V or 2.0 V, depending on the supply voltage where power consumption is of concern, the automatic power- (VDD). This input span is automatically set up by an on-chip down at the end of a conversion should be used to improve “V detector” circuit. A 5 V operation of the ADCs is detected DD power performance (see the Power vs. Throughput section). when V exceeds 4.1 V, and a 3 V operation is detected when DD If the AD7829-1 is operated outside normal VDD limits (for V falls below 3.8 V. This circuit also possesses a degree of DD example, a brown-out), it may take two conversions to reset the glitch rejection; for example, a glitch from 5.5 V to 2.7 V up to part once the correct V has been established. DD 60 ns wide does not trip the VDD detector. 2.5V The VMID pin is used to center this input span anywhere in the SUPPLY AD780 4.5V TO 5.5V range of AGND to VDD. If no input voltage is applied to VMID, 10µF 0.1µF PARALLEL INTERFACE the default input range is AGND to 2.0 V (V = 3 V ± 10%), DD V that is, centered about 1.0 V; or AGND to 2.5 V (V = 5 V ± 10%), V V DD DD REF MID that is, centered about 1.25 V. When using the default input range, DB0 TO DB7 V the V pin can be left unconnected; or, in some cases, it can be IN1 MID EOC 1.25V TO 3.75V INPUT decoupled to AGND with a 0.1 μF capacitor. RD V IN2 AD7829-1 CS If, however, an external VMID is applied, the analog input range µC/µP is from VMID − 1.0 V to VMID + 1.0 V (VDD = 3 V ± 10%), or from CONVST V IN8 VMID − 1.25 V to VMID + 1.25 V (VDD = 5 V ± 10%). A0 AGND The range of values of V that can be applied depends on the A1 MID value of V . For V = 3 V ± 10%, the range of values that can DD DD A2 DGND be applied to V is from 1.0 V to V − 1.0 V and is 1.25 V to MID DD VDD − 1.25 V when VDD = 5 V ± 10%. Table 5 shows the relevant ranges of VMID and the input span for various values of VDD. Figure 7. Typical Connection Diagram Figure 9 illustrates the input signal range available with various ADC TRANSFER FUNCTION values of VMID. The output coding of the AD7829-1 is straight binary. The Table 5. designed code transitions occur at successive integer LSB values VMID VMID Ext VMID Ext (that is, 1 LSB, 2 LSBs, and so on). The LSB size is equal to V Internal Maximum V Span Minimum V Span DD IN IN VREF/256 (VDD = 5 V), or the LSB size is equal to (0.8 VREF)/256 5.5 1.25 4.25 3.0 to 5.5 1.25 0 to 2.5 (VDD = 3 V). The ideal transfer characteristic for the AD7829-1 5.0 1.25 3.75 2.5 to 5.0 1.25 0 to 2.5 is shown in Figure 8. 4.5 1.25 3.25 2.0 to 4.5 1.25 0 to 2.5 3.3 1.00 2.3 1.3 to 3.3 1.00 0 to 2.0 = 5V) (V DD 3.0 1.00 2.0 1.0 to 3.0 1.00 0 to 2.0 11111111 1LSB = V /256 REF 111...110 2.7 1.00 1.7 0.7 to 2.7 1.00 0 to 2.0 111...000 10000000 = 3V) (V DD 000...111 1LSB = 0.8V /256 REF 000...010 000...001 00000000 1LSB V MID (V = 5V) V – 1.25V V + 1.25V – 1LSB DD MID MID (V = 3V) V – 1V V + 1V – 1LSB DD MID MID ANALOG INPUT VOLTAGE Figure 8. Transfer Characteristic Rev. 0 | Page 11 of 20 ADC CODE 06179-009 06179-008 AD7829-1 2.5V V = 5V DD V REF 5V V MID R4 AD7829-1 4V R3 V = 3.75V MID V R2 IN V V 3V R1 V = 2.5V MID 0V V IN 2V V = N/C (1.25V) MID 2.5V 1V INPUT SIGNAL RANGE FOR VARIOUS V MID 0V Figure 11. Accommodating Bipolar Signals Using External VMID EXTERNAL 2.5V V = 3V DD 3V V REF V MID R4 2V AD7829-1 R3 V = 2V MID V IN R2 V = 1.5V MID V V V = N/C (1V) R1 1V MID 0V V INPUT SIGNAL RANGE IN FOR VARIOUS V MID V MID Figure 9. Analog Input Span Variation with VMID 0V V can be used to remove offsets in a system by applying the MID Figure 12. Accommodating Bipolar Signals Using Internal V MID offset to the VMID pin, as shown in Figure 10; or it can be used NOTE: Although there is a VREF pin from which a voltage to accommodate bipolar signals by applying VMID to a level-shifting reference of 2.5 V can be sourced, or to which an external circuit before VIN, as shown in Figure 11. When VMID is being reference can be applied, this does not provide an option of driven by an external source, the source can be directly tied to varying the value of the voltage reference. As stated in the the level-shifting circuitry (see Figure 11); however, if the internal specifications for the AD7829-1, the input voltage range at this V , that is, the default value, is being used as an output, it must MID pin is 2.5 V ± 2%. be buffered before applying it to the level-shifting circuitry, because the V pin has an impedance of approximately 6 kΩ (see MID Analog Input Structure Figure 12). Figure 13 shows an equivalent circuit of the analog input V IN structure of the AD7829-1. The two diodes, D1 and D2, provide V IN ESD protection for the analog inputs. Care must be taken to ensure that the analog input signal never exceeds the supply V MID rails by more than 200 mV. This causes these diodes to become AD7829-1 forward biased and start conducting current into the substrate. 20 mA is the maximum current these diodes can conduct V MID without causing irreversible damage to the part. However, it is worth noting that a small amount of current (1 mA) conducted V MID into the substrate due to an overvoltage on an unselected channel Figure 10. Removing Offsets Using VMID can cause inaccurate conversions on a selected channel. Rev. 0 | Page 12 of 20 06179-011 06179-010 06179-013 06179-012 AD7829-1 120ns Capacitor C2 in Figure 13 is typically about 4 pF and can be TRACK CHx HOLD CHx TRACK CHx TRACK CHy HOLD CHy primarily attributed to pin capacitance. The resistor, R1, is a t 2 lumped component made up of the on resistance of several CONVST components, including that of the multiplexer and the track- t 1 and-hold. This resistor is typically about 310 Ω. Capacitor C1 EOC is the track-and-hold capacitor and has a capacitance of 0.5 pF. CS Switch 1 is the track-and-hold switch, while Switch 2 is that of the sampling capacitor, as shown in Figure 4 and Figure 5. t 3 RD V DD t 13 VALID DB0 TO DB7 C1 D1 DATA R1 0.5pF SW2 310Ω A V IN A0 TO A2 SW1 C2 D2 B 4pF ADDRESS CHANNEL y Figure 14. Channel Hopping Timing Figure 13. Equivalent Analog Input Circuit There is a minimum time delay between the falling edge of RD and the next falling edge of the CONVST signal, t . This is the 13 When in track phase, Switch 1 is closed and Switch 2 is in minimum acquisition time required of the track-and-hold to Position A; when in hold mode, Switch 1 opens, while Switch 2 maintain 8-bit performance. Figure 15 shows the typical remains in Position A. The track-and-hold remains in hold performance of the AD7829-1 when channel hopping for mode for 120 ns (see the Circuit Description section), after various acquisition times. These results were obtained using an which it returns to track mode and the ADC enters its external reference and internal VMID while channel hopping conversion phase. At this point, Switch 1 opens and Switch 2 between VIN1 and VIN4 with 0 V on Channel 4 and 0.5 V on moves to Position B. At the end of the conversion, Switch 2 Channel 1. moves back to Position A. 8.5 Analog Input Selection 8.0 On power-up, the default V selection is V . When returning IN IN1 to normal operation from power-down, the V selected is the IN 7.5 same one that was selected prior to power-down being initiated. Table 6 shows the multiplexer address corresponding to each 7.0 analog input from VIN1 to VIN8 for the AD7829-1. 6.5 Table 6. 6.0 A2 A1 A0 Analog Input Selected 0 0 0 V IN1 5.5 0 0 1 VIN2 0 1 0 VIN3 5.0 500 200 100 50 40 30 20 15 10 0 1 1 VIN4 ACQUISITION TIME (ns) 1 0 0 V IN5 Figure 15. Effective Number of Bits vs. Acquisition Time for the AD7829-1 1 0 1 V IN6 1 1 0 V IN7 The on-chip track-and-hold can accommodate input 1 1 1 VIN8 frequencies to 10 MHz, making the AD7829-1 ideal for subsampling applications. When the AD7829-1 is converting a Channel selection on the AD7829-1 is made without the 10 MHz input signal at a sampling rate of 2 MSPS, the effective necessity of a write operation. The address of the next channel number of bits typically remains above seven, corresponding to to be converted is latched at the start of the current read a signal-to-noise ratio of 42 dB, as shown in Figure 16. operation, that is, on the falling edge of RD while CS is low, as shown in Figure 14. This allows for improved throughput rates in “channel hopping” applications. Rev. 0 | Page 13 of 20 06179-014 ENOB 06179-016 06179-015 AD7829-1 50 CONVST If the falling edge of occurs after the required power- f = 2MHz SAMPLE up time has elapsed, then it is upon this falling edge that a 48 conversion is initiated. When using the on-chip reference, it is necessary to wait the required power-up time of approximately 46 25 μs before initiating a conversion. That is, a falling edge on 44 CONVST must not occur before the required power-up time has elapsed, when VDD is first connected or after the AD7829-1 42 CONVST has been powered down using the pin, as shown in Figure 17. 40 POWER VS. THROUGHPUT 38 0.2 1 3 4568 10 Superior power performance can be achieved by using the INPUT FREQUENCY (MHz) automatic power-down (Mode 2) at the end of a conversion Figure 16. SNR vs. Input Frequency on the AD7829-1 (see the Operating Modes section). POWER-UP TIMES Figure 18 shows how the automatic power-down is implemented CONVST using the signal to achieve the optimum power perform- The AD7829-1 has a 1 μs power-up time when using an external reference and a 25 μs power-up time when using the ance for the AD7829-1. The duration of the CONVST pulse is on-chip reference. When VDD is first connected, the AD7829-1 set to be equal to or less than the power-up time of the devices is in a low current mode of operation. Ensure that the CONVST (see the Operating Modes section). As the throughput rate is reduced, the device remains in its power-down state longer, and the line is not floating when VDD is applied. If there is a glitch on average power consumption over time drops accordingly. CONVST while V is rising, the part attempts to power up DD before V has fully settled and may enter an unknown state. DD t t POWER-UP CONVERT In order to carry out a conversion, the AD7829-1 must first be 1µs POWER-DOWN 330ns powered up. CONVST EXTERNAL REFERENCE t CYCLE 10µs @ 100kSPS V DD t POWER-UP Figure 18. Automatic Power-Down 1µs CONVST For example, if the AD7829-1 is operated in a continuous sampling mode, with a throughput rate of 100 kSPS and using CONVERSION INITIATED HERE an external reference, the power consumption is calculated as ON-CHIP REFERENCE follows. The power dissipation during normal operation is V DD 36 mW, VDD = 3 V. If the power-up time is 1 μs and the conversion t POWER-UP 25µs time is 330 ns (@ +25°C), the AD7829-1 can be said to dissipate CONVST 36 mW (maximum) for 1.33 μs during each conversion cycle. If the throughput rate is 100 kSPS, the cycle time is 10 μs and CONVERSION INITIATED HERE the average power dissipated during each cycle is (1.33/10) × Figure 17. AD7829-1 Power-Up Time (36 mW) = 4.79 mW. This calculation uses the minimum conversion time, thus giving the best-case power dissipation at The AD7829-1 is powered up by a rising edge on the CONVST this throughput rate. However, the actual power dissipated CONVST pin. A conversion is initiated on the falling edge of . during each conversion cycle may increase, depending on the Figure 17 shows how to power up the AD7829-1 when V is DD actual conversion time (up to a maximum of 420 ns). first connected or after the AD7829-1 has been powered down CONVST using the pin when using either the on-chip reference or an external reference. When using an external reference, the falling edge of CONVST may occur before the required power- up time has elapsed. However, the conversion is not initiated on CONVST the falling edge of but rather at the moment when the part has completely powered up, that is, after 1 μs. Rev. 0 | Page 14 of 20 SNR (dB) 06179-017 06179-018 06179-019 AD7829-1 Figure 19 shows the power vs. throughput rate for automatic, OPERATING MODES full power-down. The AD7829-1 has two possible modes of operation, depending 100 on the state of the CONVST pulse approximately 100 ns after the EOC end of a conversion, that is, upon the rising edge of the pulse. Mode 1 Operation (High-Speed Sampling) 10 When the AD7829-1 is operated in Mode 1, it is not powered down between conversions. This mode of operation allows high 1 throughput rates to be achieved. Figure 21 shows how this optimum throughput rate is achieved by bringing CONVST EOC high before the end of a conversion, that is, before the 0.1 pulses low. When operating in this mode, a new conversion should not be initiated until 30 ns after the end of a read operation. This allows the track/hold to acquire the analog 0 01 5000 150 200 250 300 350 400 450 500 signal to 0.5 LSB accuracy. THROUGHPUT (kSPS) Figure 19. AD7829-1 Power vs. Throughput Mode 2 Operation (Automatic Power-Down) 0 When the AD7829-1 is operated in Mode 2 (see Figure 22), it 2048 POINT FFT SAMPLING automatically powers down at the end of a conversion. The –10 2MSPS f = 200kHz CONVST IN signal is brought low to initiate a conversion and is –20 EOC left logic low until after the goes high, that is, approximately –30 100 ns after the end of the conversion. The state of the CONVST signal is sampled at this point (that is, 530 ns maximum after –40 CONVST falling edge) and the AD7829-1 powers down as long –50 CONVST as is low. The ADC is powered up again on the rising CONVST –60 edge of the signal. Superior power performance can be achieved in this mode of operation by powering up the –70 AD7829-1 only to carry out a conversion. The parallel interface –80 of the AD7829-1 is still fully operational while the ADCs are powered down. A read can occur while the part is powered FREQUENCY (kHz) down, and so it does not necessarily need to be placed within Figure 20. AD7829-1 SNR EOC the pulse, as shown in Figure 22. 120ns TRACK HOLD TRACK HOLD t 2 CONVST t 1 EOC CS t 3 RD VALID DB0 TO DB7 DATA Figure 21. Mode 1 Operation Rev. 0 | Page 15 of 20 (dB) POWER (mW) 0 28 57 85 113 142 170 198 227 255 283 312 340 368 396 425 453 481 510 538 566 595 623 651 680 708 736 765 793 821 850 878 906 935 963 991 06179-020 06179-021 06179-022 AD7829-1 t POWER-UP POWER DOWN HERE CONVST t 1 EOC CS RD VALID DB0 TO DB7 DATA Figure 22. Mode 2 Operation Rev. 0 | Page 16 of 20 06179-023 AD7829-1 EOC However, the pulse can be reset high by a rising edge of PARALLEL INTERFACE RD EOC . This line can be used to drive an edge-triggered The parallel interface of the AD7829-1 is eight bits wide. Figure 23 CS RD interrupt of a microprocessor. and going low accesses shows a timing diagram illustrating the operational sequence of the 8-bit conversion result. It is possible to tie CS permanently the AD7829-1 parallel interface. The multiplexer address is latched low and use only RD to access the data. In systems where the RD into the AD7829-1 on the falling edge of the input. The on- part is interfaced to a gate array or ASIC, this EOC pulse can be chip track/hold goes into hold mode on the falling edge of applied to the CS and RD inputs to latch data out of the CONVST . A conversion is also initiated at this point. When the AD7829-1 and into the gate array or ASIC. This means that the conversion is complete, the end of conversion line (EOC) pulses gate array or ASIC does not need any conversion status low to indicate that new data is available in the output register recognition logic, and it also eliminates the logic required in the of the AD7829-1. The EOC pulse stays logic low for a maximum gate array or ASIC to generate the read signal for the AD7829-1. time of 110 ns. t 2 CONVST t t 1 4 EOC t 5 CS t t 7 6 t t 8 3 RD t t 9 10 VALID DB0 TO DB7 DATA t 13 t t 11 12 NEXT CHANNEL A0 TO A2 ADDRESS Figure 23. AD7829-1 Parallel Port Timing Rev. 0 | Page 17 of 20 06179-024 AD7829-1 MICROPROCESSOR INTERFACING The parallel port on the AD7829-1 allows the ADCs to be 1 1 PIC16C6x/7x AD7829-1 interfaced to a range of many different microcontrollers. This section explains how to interface the AD7829-1 with some of PSP0 TO PSP7 DB0 TO DB7 the more common microcontroller parallel interface protocols. AD7829-1 TO 8051 CS CS Figure 24 shows a parallel interface between the AD7829-1 and the 8051 microcontroller. The EOC signal on the AD7829-1 RD RD provides an interrupt request to the 8051 when a conversion INT EOC ends and data is ready. Port 0 of the 8051 can serve as an input 1 or output port, or, as in this case when used together with the ADDITIONAL PINS OMITTED FOR CLARITY. address latch enable (ALE) of the AD8051, it can be used as a Figure 25. Interfacing to the PIC16C6x/PIC16C7x bidirectional low order address and data bus. The ALE output of the 8051 is used to latch the low byte of the address during AD7829-1 TO ADSP-21xx accesses to the device, while the high order address byte is Figure 26 shows a parallel interface between the AD7829-1 and supplied from Port 2. Port 2 latches remain stable when the the ADSP-21xx series of DSPs. As before, the EOC signal on the AD7829-1 is addressed, because they do not have to be turned AD7829-1 provides an interrupt request to the DSP when a around (set to 1) for data input, as is the case for Port 0. conversion ends. 1 1 ADSP-21xx 8051 DB0 TO DB7 D7 TO D0 DB0 TO DB7 AD0 TO AD7 1 A13 TO A0 LATCH DECODER AD7829-1 1 AD7829-1 ADDRESS DECODE CS ALE LOGIC A8 TO A15 DMS EN CS RD RD RD RD INT EOC IRQ EOC 1 ADDITIONAL PINS OMITTED FOR CLARITY. 1 ADDITIONAL PINS OMITTED FOR CLARITY. Figure 24. Interfacing to the 8051 Figure 26. Interfacing to the ADSP-21xx AD7829-1 TO PIC16C6x/PIC16C7x INTERFACING MULTIPLEXER ADDRESS INPUTS Figure 25 shows a parallel interface between the AD7829-1 and Figure 27 shows a simplified interfacing scheme between the EOC the PIC16C64/PIC16C65/PIC16C74. The signal on the AD7829-1 and any microprocessor or microcontroller that AD7829-1 provides an interrupt request to the microcontroller facilitates easy channel selection on the ADCs. The multiplexer when a conversion begins. Of the PIC16C6x/PIC16C7x range of address is latched on the falling edge of the RD signal, as outlined microcontrollers, only the PIC16C64/PIC16C65/PIC16C74 can in the Parallel Interface section, which allows the use of the three provide the option of a parallel slave port. Port D of the micro- LSBs of the address bus to select the channel address. As shown in controller operates as an 8-bit wide parallel slave port when Control Figure 27, only Address Bit A3 to Address Bit A15 are address Bit PSPMODE in the TRISE register is set. Setting PSPMODE decoded, allowing A0 to A2 to be changed according to desired RD CS enables Port Pin RE0 to be the output and RE2 to be the channel selection without affecting chip selection. (chip select) output. For this functionality, the corresponding data direction bits of the TRISE register must be configured as outputs (reset to 0). See the PIC16C6x/PIC16C7x Microcontroller User Manual for more information. Rev. 0 | Page 18 of 20 06179-025 06179-027 06179-026 AD7829-1 MICROPROCESSOR READ CYCLE 1 AD7829-1 A0 CS A1 A2 RD ADDRESS A15 TO A3 CS DECODE A15 TO A3 ADC I/O ADDRESS RD A2 TO A0 MUX ADDRESS DB7 TO DB0 DB0 TO DB7 A/D RESULT MUX ADDRESS (CHANNEL SELECTION A0 TO A2) LATCHED Figure 27. AD7829-1 Simplified Microinterfacing Scheme Rev. 0 | Page 19 of 20 SYSTEM BUS 06179-028 AD7829-1 OUTLINE DIMENSIONS 18.10 (0.7126) 17.70 (0.6969) 28 15 7.60 (0.2992) 7.40 (0.2913) 1 10.65 (0.4193) 14 10.00 (0.3937) 45° 2.65 (0.1043) 2.35 (0.0925) 0.30 (0.0118) 8° 0.10 (0.0039) 0° COPLANARITY SEATING 1.27 (0.0500) 0.51 (0.0201) 1.27 (0.0500) 0.10 0.33 (0.0130) PLANE BSC 0.31 (0.0122) 0.40 (0.0157) 0.20 (0.0079) COMPLIANT TO JEDEC STANDARDS MS-013-AE CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN. Figure 28. 28-Lead Standard Small Outline Package [SOIC_W] Wide Body (RW-28) Dimensions shown in millimeters and (inches) 9.80 9.70 9.60 28 15 4.50 4.40 4.30 6.40 BSC 1 14 PIN 1 0.65 BSC 1.20 MAX 0.15 0.05 8° 0.75 0.30 0.20 0° 0.60 COPLANARITY 0.19 SEATING 0.09 0.45 0.10 PLANE COMPLIANT TO JEDEC STANDARDS MO-153-AE Figure 29. 28-Lead Thin Shrink Small Outline Package [TSSOP] (RU-28) Dimensions shown in millimeters ORDERING GUIDE Model Temperature Range Package Description Package Option Linearity Error AD7829BRU-1 −40°C to +85°C 28-Lead Thin Shrink Small Outline Package [TSSOP] RU-28 ±0.75 LSB AD7829BRU-1REEL7 −40°C to +85°C 28-Lead Thin Shrink Small Outline Package [TSSOP] RU-28 ±0.75 LSB 1 AD7829BRUZ-1 −40°C to +85°C 28-Lead Thin Shrink Small Outline Package [TSSOP] RU-28 ±0.75 LSB 1 AD7829BRUZ-1REEL7 −40°C to +85°C 28-Lead Thin Shrink Small Outline Package [TSSOP] RU-28 ±0.75 LSB AD7829BRW-1 −40°C to +85°C 28-Lead Standard Small Outline Package [SOIC_W] RW-28 ±0.75 LSB AD7829BRW-1RL7 −40°C to +85°C 28-Lead Standard Small Outline Package [SOIC_W] RW-28 ±0.75 LSB 1 AD7829BRWZ-1 −40°C to +85°C 28-Lead Standard Small Outline Package [SOIC_W] RW-28 ±0.75 LSB 1 AD7829BRWZ-1RL7 −40°C to +85°C 28-Lead Standard Small Outline Package [SOIC_W] RW-28 ±0.75 LSB 1 Z = Pb-free part. ©2006 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D06179-0-7/06(0) Rev. 0 | Page 20 of 20 0.75 (0.0295) 0.25 (0.0098) 060706-A
Frequently asked questions
What makes Elite.Parts unique?
What kind of warranty will the AD7829-1 have?
Which carriers does Elite.Parts work with?
Will Elite.Parts sell to me even though I live outside the USA?
I have a preferred payment method. Will Elite.Parts accept it?
Manufacturers


What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods