Elite.Parts Manufacturers A ANALOG DEVICES AD7821
About product Specifications Features Datasheet FAQ

ANALOG DEVICES AD7821

Description

Analog Devices AD7821 High Speed, 8-Bit, Sampling, Analog-to-Digital Converter

Part Number

AD7821

Price

Request Quote

Manufacturer

ANALOG DEVICES

Lead Time

Request Quote

Category

PRODUCTS - A

Specifications

# Chan

1

ADC Architecture

Pipelined

Ain Range

Bip (Vref),Uni (Vref)

Analog Input Type

SE-Bip,SE-Uni

Interface

Par

Pkg Type

DIP,LCC,SOIC

Resolution (Bits)

8bit

Sample Rate

1MSPS

Features

Datasheet

pdf file

AD7821-1986248785.pdf

811 KiB

Extracted Text

2 LC MOS High Speed, �P Compatible a 8-Bit ADC with Track/Hold Function AD7821 FUNCTIONAL BLOCK DIAGRAM FEATURES Fast Conversion Time: 660 ns Max 100 kHz Track-and-Hold Function 1 MHz Sample Rate Unipolar and Bipolar Input Ranges Ratiometric Reference Inputs No External Clock Extended Temperature Range Operation Skinny 20-Lead DlPs, SOIC, and 20-Terminal Surface-Mount Packages GENERAL DESCRIPTION PRODUCT HIGHLIGHTS The AD7821 is a high speed, 8-bit, sampling, analog-to-digital 1. Fast Conversion Time converter that offers improved performance over the popular The half-flash conversion technique, coupled with fabrication 2 AD7820. It offers a conversion time of 660 ns (versus 1.36 µs on Analog Devices’ LC MOS process, enables a very fast con- for the AD7820) and 100 kHz signal bandwidth (versus 6.4 version time. The conversion time for the WR-RD mode is kHz). The sampling instant is better defined and occurs on the 660 ns, with 700 ns for the RD mode. falling edge of WR or RD. The provision of a V pin (Pin 19) SS 2. Built-In Track-and-Hold allows the part to operate from ±5 V supplies and to digitize This allows input signals with slew rates up to 1.6 V/µs to be bipolar input signals. Alternatively, for unipolar inputs, the V pin SS converted to 8 bits without an external track-and-hold. This can be grounded and the AD7821 will operate from a single +5 V corresponds to a 5 V peak-to-peak, 100 kHz sine wave signal. supply, like the AD7820. 3. Total Unadjusted Error The AD7821 has a built-in track-and-hold function capable of The AD7821 features an excellent total unadjusted error figure digitizing full-scale signals up to 100 kHz max. It also uses a of less than ±1 LSB over the full operating temperature range. half-flash conversion technique that eliminates the need to gen- 4. Unipolar/Bipolar Input Ranges erate a CLK signal for the ADC. The AD7821 is specified for single-supply (+5 V) operation The AD7821 is designed with standard microprocessor control with a unipolar full-scale range of 0 to +5 V, and for dual-supply signals (CS, RD, WR, RDY, INT) and latched, three-state data (±5 V) operation with a bipolar input range of ±2.5 V. Typical outputs capable of interfacing to high speed data buses. An performance characteristics are given for other input ranges. overflow output (OFL) is also provided for cascading devices to 5. Dynamic Specifications for DSP Users achieve higher resolution. In addition to the traditional ADC specifications, the The AD7821 is fabricated in Linear Compatible CMOS AD7821 is specified for ac parameters, including signal-to- 2 (LC MOS), an advanced, mixed technology process combining noise ratio, distortion, and slew rate. precision bipolar circuits with low power CMOS logic. The part features a low power dissipation of 50 mW. REV. B Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. use, nor for any infringements of patents or other rights of third parties that Tel: 781/329-4700 www.analog.com may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Fax: 781/326-8703 © Analog Devices, Inc., 2002 V = +5 V � 5%, GND = 0 V. Unipolar Input Range: V = GND, V (+) = 5 V, DD SS REF AD7821–SPECIFICATIONS V (–) = GND. Bipolar Input Range: V = –5 V � 5%, V (+) = 2.5 V, REF SS REF V (–) = –2.5 V. These test conditions apply unless otherwise stated. All specifications T to T unless otherwise noted. Specifications REF MIN MAX apply for RD Mode (Pin 7 = 0 V). 1 Parameter K Version B, T Versions Unit Comments UNIPOLAR INPUT RANGE 2 Resolution 88 Bits 3 Total Unadjusted Error ±1 ±1 LSB max Minimum Resolution for which No Missing Codes are Guaranteed 8 8 Bits BIPOLAR INPUT RANGE 2 Resolution 88 Bits Zero Code Error ±1 ±1 LSB max Full Scale Error ±1 ±1 LSB max 3 Signal-to-Noise Ratio (SNR) 45 45 dB min V = 99.85 kHz Full-Scale Sine Wave with f = 500 kHz IN SAMPLING 3 Total Harmonic Distortion (THD) –50 –50 dB max V = 99.85 kHz Full-Scale Sine Wave with f = 500 kHz IN SAMPLING 3 Peak Harmonic or Spurious Noise –50 –50 dB max V = 99.85 kHz Full-Scale Sine Wave with f = 500 kHz IN SAMPLING 3 Intermodulation Distortion (IMD) fa (84.72 kHz) and fb (94.97 kHz) Full-Scale Sine Waves with f = 500 kHz SAMPLING –50 –50 dB max Second Order Terms –50 –50 dB max Third Order Terms 3 Slew Rate, Tracking 1.6 1.6 V/µs max 2.36 2.36 V/µs typ REFERENCE INPUT Input Resistance 1.0/4.0 1.0/4.0 kΩ min/kΩ max V (+) Input Voltage Range V (–)/V V (–)/V V min/V max REF REF DD REF DD V (–) Input Voltage Range V /V (+) V /V (+) V min/V max REF SS REF SS REF ANALOG INPUT Input Voltage Range V (–)/V (+) V (–)/V (+) V min/ max REF REF REF REF Input Leakage Current ±3 ±3 µA max –5 V ≤ V ≤ +5 V IN Input Capacitance 55 55 pF typ LOGIC INPUTS CS, WR, RD V 2.4 2.4 V min INH V 0.8 0.8 V max INL I (CS, RD)1 1 µA max INH I (WR)3 3 µA max INH I –1 –1 µA max INL 4 Input Capacitance 88 pF max Typically 5 pF MODE V 3.5 3.5 V min INH V 1.5 1.5 V max INL I 200 200 µA max 50 µA typ INH I –1 –1 µA max INL 4 Input Capacitance 88 pF max Typically 5 pF LOGIC OUTPUTS DB0–DB7, OFL, INT V 4.0 4.0 V min I = 360 µA OH SOURCE V 0.4 0.4 V max I = 1.6 mA OL SINK I (DB0–DB7) ±3 ±3 µA max Floating State Leakage OUT 4 Output Capacitance (DB0–DB7) 8 8 pF max Typically 5 pF RDY V 0.4 0.4 V max I = 2.6 mA OL SINK I ±3 ±3 µA max Floating State Leakage OUT 4 Output Capacitance 88 pF max Typically 5 pF POWER SUPPLY 5 I 20 20 mA max CS = RD = 0 V DD I 100 100 µA max CS = RD = 0 V SS Power Dissipation 50 50 mW typ Power Supply Sensitivity ±1/4 ±1/4 LSB max ±1/16 LSB typ, V = 4.75 V to 5.25 V, DD (V (+) = 4.75 V max for Unipolar Mode) REF NOTES 1 Temperature Ranges are as follows: K Version = –40°C to +85°C; B Version = –40°C to +85°C; T Version = –55°C to +125°C. 2 1 LSB = 19.53 mV for both the unipolar (0 V to +5 V) and bipolar (–2.5 V to +2.5 V) input ranges. 3 See Terminology. 4 Sample tested at +25°C to ensure compliance. 5 See Typical Performance Characteristics. Specifications subject to change without notice. –2– REV. B AD7821 1 TIMING CHARACTERISTICS (V = +5 V � 5%, V = 0 V or –5 V � 5%; Unipolar or Bipolar Input Range) DD SS Limit at Limit at Limit at +25�CT , T T , T MIN MAX MIN MAX Parameter (All Versions) (K, B Versions) (T Version) Unit Conditions/Comments t 000 ns min CS to RD/WR Setup Time CSS t 000 ns min CS to RD/WR Hold Time CSH 2 t 70 85 100 ns max CS to RDY Delay. Pull-Up RDY Resistor 5 kΩ t 700 875 975 ns max Conversion Time (RD Mode) CRD 3 t Data Access Time (RD Mode) ACC0 t + 25 t + 30 t + 35 ns max C = 20 pF CRD CRD CRD L t + 50 t + 65 t + 75 ns max C = 100 pF CRD CRD CRD L 2 t 50 – – ns typ RD to INT Delay (RD Mode) INTH 80 85 90 ns max 4 t 15 15 15 ns min Data Hold Time DH 60 70 80 ns max t 350 425 500 ns min Delay Time Between Conversions P t 250 325 400 ns min Write Pulsewidth WR 10 10 10 µs max t 250 350 450 ns min Delay Time between WR and RD Pulses RD t 160 205 240 ns min RD Pulsewidth (WR-RD Mode, see Figure 12b) READ1 Determined by t ACC1 3 t Data Access Time (WR-RD Mode, see Figure 12b) ACC1 160 205 240 ns max C = 20 pF L 185 235 275 ns max C = 100 pF L t 150 185 220 ns max RD to INT Delay RI 2 t 380 – – ns typ WR to INT Delay INTL 500 610 700 ns max t 65 75 85 ns min RD Pulsewidth (WR-RD Mode, see Figure 12a) READ2 Determined by t ACC2 Data Access Time (WR-RD Mode, see Figure 12a) 3 t 65 75 85 ns max C = 20 pF ACC2 L 90 110 130 ns max C = 100 pF L 2 t 80 100 120 ns max WR to INT Delay (Stand-Alone Operation) IHWR 3 t Data Access Time after INT ID (Stand-Alone Operation) 30 35 40 ns max C = 20 pF L 45 60 70 ns max C = 100 pF L NOTES 1 Sample tested at +25°C to ensure compliance. All input control signals are specified with t = t = 5 ns (10% to 90% of +5 V) and timed from a voltage level of 1.6 V. RISE FALL 2 C = 50 pF. L 3 Measured with load circuits of Figure 1 and defined as the time required for an output to cross 0.8 V or 2.4 V. 4 Defined as the time required for the data lines to change 0.5 V when loaded with the circuits of Figure 2. Specifications subject to change without notice. ORDERING GUIDE Test Circuits Total Temperature Unadjusted Package 1 2 Model Range Error (LSB) Option AD7821KN –40°C to +85°C ±1 max N-20 AD7821KP –40°C to +85°C ±1 max P-20A AD7821KR –40°C to +85°C ±1 max RW-20 AD7821BQ –40°C to +85°C ±1 max Q-20 a. High Z to V b. High Z to V AD7821TQ –55°C to +125°C ±1 max Q-20 OH OL AD7821TE –55°C to +125°C ±1 max E-20A Figure 1. Load Circuits for Data Access Time Test NOTES 1 To order MIL-STD-883, Class B processed parts, add /883B to part number. Contact local sales office for military data sheet. 2 E = Leadless Ceramic Chip Carrier; N = Plastic DIP; P = Plastic Leaded Chip Carrier; Q = Cerdip; R = SOIC. a. V to High Z b. V to High Z OH OL Figure 2. Load Circuits for Data Hold Time Test REV. B –3– AD7821 ABSOLUTE MAXIMUM RATINGS* Industrial (B Version) . . . . . . . . . . . . . . . . –40°C to +85°C V to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V, + 7 V Extended (T Version) . . . . . . . . . . . . . . . –55°C to +125°C DD V to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . +0.3 V, + 7 V Storage Temperature Range . . . . . . . . . . . . –65°C to +150°C SS Digital Input Voltage to GND Lead Temperature (Soldering, 10 sec) . . . . . . . . . . . .+300°C (Pins 6–8, 13) . . . . . . . . . . . . . . . . . . . –0.3 V, V + 0.3 V Power Dissipation (Any Package) to +75°C . . . . . . . 450 mW DD Digital Output Voltage to GND Derates above +75°C by . . . . . . . . . . . . . . . . . . . . . 6 mW/°C (Pins 2–5, 9, 14–18) . . . . . . . . . . . . . . . –0.3 V, V + 0.3 V DD *Stresses above those listed under “Absolute Maximum Ratings” may cause V (+) to GND . . . . . . . . . . . . . . . V – 0.3 V, V + 0.3 V REF SS DD permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the V (–) to GND . . . . . . . . . . . . . . . V – 0.3 V, V + 0.3 V REF SS DD operational sections of this specification is not implied. Exposure to absolute V to GND . . . . . . . . . . . . . . . . . . . V – 0.3 V, V + 0.3 V IN SS DD maximum rating conditions for extended periods may affect device reliability. Operating Temperature Range Commercial (K Version) . . . . . . . . . . . . . . –40°C to +85°C CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily WARNING! accumulate on the human body and test equipment and can discharge without detection. Although the AD7821 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD ESD SENSITIVE DEVICE precautions are recommended to avoid performance degradation or loss of functionality. PIN CONFIGURATIONS DIP AND SOIC LCCC PLCC PIN FUNCTION DESCRIPTIONS Pin Mnemonic Description 1V Analog Input: Range V (–) ≤ V ≤ V (+) IN REF IN REF 2 DB0 Three-State Data Output (LSB) 3–5 DB1–DB3 Three-State Data Outputs 6 WR/RDY WRITE control input/READY status output. See Digital Interface section. 7 MODE Mode Selection Input. It determines whether the device operates in the WR-RD or RD mode. This input is internally pulled low through a 50 µA current source. See Digital Interface section. 8 RD READ Input. RD must be low to access data from the part. See Digital Interface section. 9 INT INTERRUPT Output. INT going low indicates that the conversion is complete. INT returns high on the rising edge of CS or RD. See Digital Interface section. 10 GND Ground 11 V (–) Lower limit of reference span. REF Range: V ≤ V (–) ≤ V (+). SS REF REF 12 V (+) Upper limit of reference span. REF Range: V (–) < V (+) ≤ V . REF REF DD 13 CS Chip Select Input. The device is selected when this input is low. 14–16 DB4–DB6 Three-State Data Outputs 17 DB7 Three-State Data Output (MSB) 18 OFL Overflow Output. If the analog input is higher than (V (+) – 1/2 LSB), OFL will be low at the end of conversion. It REF is a non-three-state output which can be used to cascade two or more devices to increase resolution. 19 V Negative Supply Voltage SS V = 0 V; Unipolar Operation SS V = –5 V; Bipolar Operation SS 20 V Positive Supply Voltage, +5 V DD –4– REV. B AD7821 TERMINOLOGY INTERMODULATION DISTORTION LEAST SIGNIFICANT BIT (LSB) With inputs consisting of sine waves at two frequencies, fa and 8 An ADC with 8-bit resolution can resolve one part in 2 (1/256 fb, any active device with nonlinearities will create distortion of full scale). For the AD7821 operating in either the unipolar products, of order (m+n), at sum and difference frequencies of or bipolar input range with 5 V full scale, one LSB is 19.53 mV. mfa+nfb, where m, n = 0, 1, 2, 3…. Intermodulation terms are those for which m or n is not equal to zero. For example, the TOTAL UNADJUSTED ERROR second order terms include (fa + fb) and (fa – fb), and the third This is a comprehensive specification which includes relative order terms include (2fa + fb), (2fa – fb), (fa + 2fb) and accuracy, offset error, and full-scale error. (fa – 2fb). For the AD7821 intermodulation distortion is calcu- lated separately for both the second and third order terms. SLEW RATE Slew rate is the maximum allowable rate of change of input SIGNAL-TO-NOISE RATIO (SNR) signal such that the digital sample values are not in error. Signal-to-noise ratio is measured signal-to-noise at the output of the ADC. The signal is the rms magnitude of the fundamental. TOTAL HARMONIC DISTORTION (THD) Noise is the rms sum of all nonfundamental signals (excluding Total harmonic distortion is the ratio of the square root of the dc) up to half the sampling frequency. SNR is dependent on the sum of the squares of the rms value of the harmonics to the rms number of quantization levels used in the digitization process. value of the fundamental. For the AD7821, total harmonic dis- The theoretical SNR for a sine wave input is given by: tortion is defined as SNR=+ 60.. 2N 176 dB ()  2 2 2 2 2  VVV ++ ++ VV () 2 3 4 5 6 where N is the number of bits in the ADC. Thus, for an ideal   20 log dB   8-bit ADC, SNR = 50 dB. V 1     PEAK HARMONIC OR SPURIOUS NOISE where V is the rms amplitude of the fundamental and V , V , V , 1 2 3 4 Peak harmonic or spurious noise is the rms value of the largest V , and V are the rms amplitudes of the individual harmonics. 5 6 nonfundamental frequency (excluding dc) up to half the sam- pling frequency to the rms value of the fundamental. REV. B –5– AD7821—Typical Performance Characteristics TPC 2. Power Supply Current vs. TPC 3. Accuracy vs. t TPC 1. Conversion Time WR Temperature (Not Including (RD Mode) vs.Temperature Reference Ladder) TPC 6. Accuracy vs. V REF TPC 5. Accuracy vs. t TPC 4. Accuracy vs. t P RD [V = V (+) – V (–)] REF REF REF TPC 7. Effective Number of Bits vs. TPC 8. t , Internal Time Delay vs. TPC 9. Output Current vs. INTL Input Signal (±2.5 V) Frequency Temperature Temperature –6– REV. B AD7821 CIRCUIT INFORMATION As a result, the analog input (V ) of the device can easily be set IN up to provide both unipolar and bipolar operation. The data BASIC DESCRIPTION output code for unipolar and bipolar operation is Natural Binary The AD7821 uses a half flash conversion technique (see Func- and Offset Binary, respectively. tional Block Diagram), whereby two 4-bit flash ADCs are used to achieve an 8-bit result. Each 4-bit flash ADC contains 15 The span of the analog input voltage can easily be varied. By comparators, which compare an unknown input voltage to the reducing the reference span, V (+) – V (–), to less than 5 V, REF REF reference ladder, to achieve a 4-bit result. The MS (most signifi- the sensitivity of the converter can be increased (i.e., if V = 2 V REF cant) flash ADC converts an unknown analog input voltage (V ) IN then 1 LSB = 7.8 mV). The reference flexibility also allows the to provide the 4 MS data bits. An internal DAC, driven by the 4 MS input span for unipolar operation to be offset from zero (V (–) > REF data bits, then recreates an analog approximation of the input GND). Additionally, the input/reference arrangement facilitates voltage. The DAC output voltage is subtracted from the analog ratiometric operation. input, and the difference is converted by the LS (least significant) Figures 4 and 5 show some configurations that are possible. For ADC to provide the 4 LS data bits. The MS flash ADC also has one minimum noise, a 47 µF capacitor in parallel with a 0.1 µF ca- additional comparator to detect over-range on the analog input. pacitor should be connected between the reference inputs and GND. OPERATING SEQUENCE The AD7821 has two operating modes. The RD mode allows a con- version to be started and data to be read with a single, extended, READ operation (i.e., CS and RD are taken low). The conversion process is timed out by internal one-shots. The WR-RD mode uses WR to start a conversion and RD to read the data and allows the conversion timing to be externally controlled. The operating sequence for the WR-RD mode is shown in Figure 3. Figure 4. Power Supply as Reference; Unipolar Operation (0 to + 5 V) Figure 3. Operating Sequence (WR-RD Mode) A conversion is initiated and the analog input signal (V ) sampled IN on the falling edge of WR (falling edge of RD, RD mode). A setup time (t , delay time between conversions) of 350 ns is required P prior to this falling edge. See the Digital Interface section for more details. When WR is low, the internal MS (most significant) ADC compares the sampled analog input with the reference ladder to provide the 4 MS data bits. A minimum of 250 ns is required for this comparison. On the rising edge of WR, the MS data result is latched internally and the LS (least significant) conversion begins, to yield the 4 LS data bits. INT goes low typically 380 ns after the rising edge of WR. This indicates the LS conversion is complete and that both the LS and MS data results are latched into the output buffer. RD going low then enables the output data. If a faster conversion time is required, the RD line can be brought low Figure 5. External Reference; 250 ns after WR goes high. This latches both the LS and MS Bipolar Operation (–2.5 V to +2.5 V) data bits and outputs the conversion result on DB0–DB7. INPUT CURRENT REFERENCE AND INPUT The analog input of the AD7821 behaves somewhat differently The V (–) and V (+) reference inputs on the AD7821 are REF REF than conventional ADCs. This is due to the ADC’s sampled fully differential and define the zero and full-scale input range of data comparators, which take varying amounts of input current the ADC. The transfer characteristic of the part is defined by depending on the cycle of the converter. the integer value of the following expression: The equivalent input circuit of the AD7821 is shown in Figure 6.   V −V (−) When a conversion ends (e.g., falling edge of INT, WR-RD IN REF Data (LSBs) = 256 + 0.5   V (+) −V (−) mode, t > t ) all the input switches are closed and V is RD INTL IN  REF REF  connected to the comparators of the internal LS and MS ADCs. Therefore, V is simultaneously connected to 31 input capacitors IN of 1 pF each. REV. B –7– AD7821 INHERENT TRACK-AND-HOLD A major benefit of the AD7821’s input structure is its ability to measure a variety of high speed signals without the help of an external track-and-hold. Any ADC which does not have a built-in track-and-hold, regardless of its speed, requires the analog input to remain stable to at least 1/2 LSB for the duration of the conver- sion to maintain full accuracy. This requires the use of a track-and-hold whenever the input is a high-speed signal. The AD7821’s sampled-data comparators, by nature of their input switching, inherently accomplish this track-and-hold function. Although the conversion time for the AD7821 is 660 ns (WR-RD mode, t + t + t ), the time for which V must be stable WR RD ACC1 IN to 1/2 LSB is much smaller. The AD7821 tracks V between IN conversions only, and its value on the falling edge of WR or RD in the WR-RD or RD modes, respectively, is the measured value. Figure 6. AD7821 Equivalent Input Circuit SINUSOIDAL INPUTS The input capacitors must charge to the input voltage through the The bandwidth of the built-in track-and-hold is 100 kHz max on resistance of the analog switches (about 2 kΩ to 5 kΩ). In (150 kHz typ, 5 V p-p). This is limited by the analog bandwidth addition, about 12 pF of input stray capacitance must be charged. of the comparators and timing skew between the comparator The analog input can be modeled as an equivalent RC network switches. This means that the analog input frequency can be up as shown in Figure 7. As R (source impedance) increases, the S to 100 kHz without the aid of an external track-and-hold. The input capacitance takes longer to charge. Nyquist criterion requires that the sampling rate be at least The comparators track the analog input between conversions. twice the input frequency (i.e., ≥2 � 100 kHz). This requires an A minimum delay time (t ) of 350 ns is required between ideal antialiasing filter with an infinite roll-off. To ease the prob- P conversions to allow for voltage source settling and comparator lem of antialiasing filter design, the sampling rate is usually set tracking time. This allows input time constants of 50 ns without much greater than the Nyquist criterion. The maximum sampling settling time problems. Typical total input capacitance values of rate (f ) for the AD7821 in the WR-RD mode, (t < t ) MAX RD INTL 55 pF allow R to be 0.9 kΩ without lengthening t to give V can be calculated as follows: S P IN more time to settle. 1 f = MAX tt++t +t WR RD RI P 1 f = MAX −−−− 6666 02.... 5 ×10+× 025 10+× 0 15 10+× 0 35 10 ()()()() t = Write Pulsewidth WR t = Delay Time between WR and RD Pulses RD t = RD to INT Delay RI t = Delay Time between Conversions P Figure 7. RC Network Model This permits a maximum sampling rate for the AD7821 of INPUT TRANSIENTS 1 MHz, which is much greater than the Nyquist criterion for Transients on the analog input signal caused by charging current sampling a 100 kHz analog input signal. flowing into V will not normally degrade the ADC’s perfor- IN mance. In effect, the AD7821 does not “look” at the input when DIGITAL SIGNAL PROCESSING APPLICATIONS these transients occur. The comparators’ inputs track V and are IN In Digital Signal Processing (DSP) application areas such as voice not sampled until the falling edge of WR (WR-RD Mode) or recognition, echo cancellation, and adaptive filtering, the dynamic RD (RD Mode), so at least 350 ns (t ) is provided to charge the P characteristics (Signal-to-Noise Ratio, Harmonic Distortion, ADC’s input capacitance. It is, therefore, not necessary to filter Intermodulation Distortion) of an ADC are critical. Since the out these transients with an external capacitor at the V terminal. IN AD7821 is a very fast ADC with a built-in track-and-hold function, it is specified dynamically as well as with standard dc specifications (Total Unadjusted Error, and so on). –8– REV. B AD7821 SIGNAL-TO-NOISE RATIO AND DISTORTION possible to plot a histogram showing the frequency of occurrence The dynamic performance of the AD7821 is evaluated by apply- of each of the 256 ADC codes. A perfect ADC produces a ing a very low distortion sine wave signal to the analog input probability density function described by the equation: (V ) which is then sampled at a 512 kHz sampling rate. A Fast IN 1 P(V ) = Fourier Transform (FFT) plot is then generated from which 2 2 1/2 π( A −V ) Signal-to-Noise Ratio (SNR) and harmonic distortion data are obtained. where A is the peak amplitude of the sine wave and P(V) is the probability of occurrence at a voltage V. Figure 8 shows a 2048 point FFT plot of the AD7821 with an input signal of 100.25 kHz. The SNR is 49.1 dB. It should be If a particular step is wider than the ideal 1 LSB width, then the noted that the harmonics are taken into account when calculat- code associated with that step will accumulate more counts than ing the SNR. The theoretical relationship between SNR and for the code for an ideal step. Likewise, a step narrower than the resolution (N) is expressed by the following equation: ideal width will have fewer counts. Missing codes are easily seen because a missing code means zero counts for a particular code. SNR=+ 60.. 2N 176 dB (1) () The absence of large spikes in the plot indicates small differ- ential nonlinearity. Figure 10 shows a histogram plot for the AD7821, which corre- sponds very well with the ideal shape. The plot indicates very small differential nonlinearity and no missing codes for an input frequency of 100.25 kHz. Figure 8. FFT Plot EFFECTIVE NUMBER OF BITS By working backwards from Equation (1) it is possible to get a measure of ADC performance expressed in effective number of bits (N). A plot of the effective number of bits versus input frequency is given in the Typical Performance Characteristics section. The effective number of bits typically falls between 7.7 and 7.9, corresponding to SNR figures of 48.1 dB and 49.7 dB. Figure 10. Histogram Plot INTERMODULATION DISTORTION For intermodulation distortion (IMD), an FFT plot consisting In digital signal processing applications, where the AD7821 is of very low distortion sine waves at two frequencies is generated used to sample ac signals, it is essential that the signal sampling by sampling an analog input applied to the ADC. Figure 9 occurs at exactly equal intervals. This minimizes errors due to shows a 2048 point plot for IMD. sampling uncertainty or jitter. A precise timer or clock source, to start the ADC conversion process, is the best method of gen- erating equidistant sampling intervals. The two modes of operation given in the data sheet are suitable for DSP applications because the sampling instant of the AD7821 is well defined. V is sampled on the falling edge of IN WR or RD in the WR-RD or RD modes, respectively. DIGITAL INTERFACE The AD7821 has two basic interface modes which are determined by the status of the MODE pin. When this pin is low, the converter is in the RD mode, with this pin high, the AD7821 is set up for the WR-RD mode. The RD mode is designed for microprocessors that can be driven into a WAIT state. A READ operation (i.e., CS and RD are taken low) starts a conversion and data is read when the conversion is Figure 9. FFT Plot for IMD complete. The WR-RD mode does not require microprocessor WAIT states. A WRITE operation (i.e., CS and WR are taken HISTOGRAM PLOT low) initiates a conversion, and a READ operation reads the When a sine wave of specified frequency is applied to the V input result when the conversion is complete. IN of the AD7821 and several thousand samples are taken, it is REV. B –9– AD7821 RD Mode (MODE = 0) The timing diagram for the RD mode is shown in Figure 11. This mode is intended for use with microprocessors that have a WAIT state facility, whereby a READ instruction cycle can be extended to accommodate slow memory devices. A conversion is started by taking CS and RD low (READ operation). Both CS and RD are then kept low until output data appears. Figure 12a. WR-RD Mode (t > t ) RD INTL The alternative option can be used to shorten the conversion time. This is a method for bypassing the internal time-out circuit. The INT line is ignored and RD can be brought low 250 ns after the rising edge of WR. In this case RD going low transfers the data result into the output latch and activates the data output (DB0–DB7). INT is driven low on the falling edge of RD and is reset on the rising edge of RD or CS. The timing for this interface is shown in Figure 12b. Figure 11. RD Mode In this mode, Pin 6 of the AD7821 is configured as a status out- put, RDY. This RDY output can be used to drive the processor READY or WAIT input. It is an open-drain output (no inter- nal-pull-up device) which goes low after the falling edge of CS and goes high impedance at the end of conversion. An INT line is also provided which goes low when a conversion is complete. INT returns high on the rising edge of CS or RD. WR-RD Mode (MODE = 1) In the WR-RD mode, Pin 6 is configured as a WRITE (WR) input for the AD7821. With CS low, conversion is initiated on the falling edge of WR. Two options exist for reading data from the converter. In the first of these options the processor waits for the INT status line to go low before reading the data (see Figure 12a). Figure 12b. WR-RD Mode (t < t ) RD INTL INT typically goes low within 380 ns after the rising edge of WR. The AD7821 can also be used in standalone operation in the It indicates that conversion is complete and that the data result is WR-RD mode. CS and RD are tied low, and a conversion is initi- in the output latch. With CS low, the data outputs (DB0–DB7) ated by bringing WR low. Output data is valid 530 ns (t + t ) INTL ID are activated when RD goes low. INT is reset by the rising edge after the rising edge of WR. The timing diagram for this mode is of RD or CS. shown in Figure 13. Figure 13. WR-RD Mode Stand-Alone Operation, CS = RD = 0 –10– REV. B AD7821 MICROPROCESSOR INTERFACING AD7821 – TMS32010 INTERFACE The AD7821 is designed for easy interfacing to microprocessors A typical interface to the TMS32010 is shown in Figure 16. The as a memory mapped peripheral or an I/O device. This reduces AD7821 is mapped at a port address and the interface is designed to a minimum the amount of external logic required for for the maximum TMS32010 clock frequency of 20 MHz. In this interfacing. case, the AD7821 is configured in the WR-RD interface mode. This means that a write instruction starts a conversion and a read AD7821 – 68008 INTERFACE instruction reads the result when the conversion is completed. A Figure 14 shows an AD7821 interface to the 68008 micropro- precise timer or clock source is used to start a conversion in cessor. The ADC is configured for the RD interface mode. This applications requiring equidistant sampling intervals. The means that one read instruction starts a conversion and reads scheme used, whereby the AD7821 generates an interrupt to the result when the conversion is completed. The read cycle is the TMS32010, is limited in that it does not allow the AD7821 stretched out over the entire conversion period by taking the to be sampled at its maximum rate. This is because the time INT line back to the DTACK input of the 68008. Starting a between samples has to be long enough to allow the TMS32010 conversion and reading the relevant data consists of a instruction, where addr is the decoded ADC address and Constant interruption of the TMS32010 by the AD7821, every time Dn is the data register into which the result is placed. the ADC completes a conversion, is not a very efficient use of the processor time. To overcome these problems, some buffer memory or FIFO could be placed between the AD7821 and the TMS32010. The INT line of the AD7821 could be used to trigger a pulse which drives its CS and RD lines and places the AD7821 data into a FIFO or buffer memory. The microproces- sor can then read a batch of data from the FIFO or buffer memory at some convenient time. Reading data from the AD7821, after an INT has been received, consists of a instruction (PA is the decoded ADC address). Figure 14. AD7821 to 68008 Interface AD7821 – 8088 INTERFACE A typical interface to the 8088 is shown in Figure 15. The AD7821 is configured for the RD interface mode. One read instruction starts a conversion and reads the result. The read cycle is stretched out over the entire conversion period by taking the RDY line back to the READY input of the 8088. Starting a conversion and reading the result consists of a instruction, where addr is the decoded ADC address and AX is the 8088 data Figure 16. AD7821 to TMS32010 Interface register into which the conversion result is placed. AD7821 – 8051 INTERFACE Figure 17 shows the AD7821 interface to the 8051 microcom- puter. The AD7821 is configured in the WR-RD interface mode and is connected to the 8051 ports. The processor starts conver- sion and then polls INT, until it goes low, before reading the conversion result. Data is read from the AD7821 by using the instruction (90H is the address for Port 1). Figure 15. AD7821 to 8088 Interface Figure 17. AD7821 to 8051 Interface REV. B –11– AD7821 APPLYING THE AD7821 BIPOLAR OPERATION The AD7821 is specified for a unipolar input range of 0 V to +5 V Figure 18 gives the configuration and reference voltages required and a bipolar input range of –2.5 V to +2.5 V. The V (–) and for –2.5 V to +2.5 V operation. The nominal transfer characteris- REF V (+) voltages required for these input ranges are outlined tic for this input range is shown in Figure 20. The output code is REF below. See the Typical Performance Characteristics section for Offset Binary with 1 LSB = ([+2.5 – (–2.5)]/256) V = 19.5 mV. operation with unspecified input voltage ranges. UNIPOLAR OPERATION Figure 18 gives the configuration and reference voltages required for 0 V to +5 V operation. The nominal transfer characteristic for this input range is shown in Figure 19. The output code is Natural Binary with 1 LSB = (5/256) V = 19.5 mV. Figure 20. Nominal Transfer Characteristic for Bipolar (–2.5 V to +2.5 V) Operation 16-CHANNEL TELECOM A/D CONVERTER The fast sampling rate (1 MHz) and bipolar operation of the AD7821 makes it useful in telecom applications for sampling a Figure 18. Unipolar/Bipolar Operation number of input channels using a multiplexer. Figure 21 shows a circuit for such an application. The maximum signal frequency required for acceptable quality in telecom applications is 3 kHz. The circuit given in Figure 21 permits each of the 16-input channels to be sampled at a rate of 16 kHz maximum. The sampling rate takes into account such multiplexer parameters as t , settling time, and so on. The ON circuit also eases the problem of the antialiasing filter design by sampling at a rate much greater than that required by the Nyquist criterion. Figure 19. Nominal Transfer Characteristic for Unipolar (0 V to +5 V) Operation –12– REV. B AD7821 Figure 21. 16-Channel Telecom ADC System SIMULTANEOUS SAMPLING ADCS The AD7821’s inherent track-and-hold and well defined sampling instant makes it useful in such applications as sonar, where a num- ber of input channels are required to be sampled simultaneously. Figure 22 shows a circuit for such an application. Figure 22. Simultaneous Sampling ADCs The actual sampling instant at which V is measured occurs IN approximately 50 ns after the falling edge of WR or RD in the WR-RD or RD modes, respectively, due to internal logic delays. However, the internal logic delay and, therefore, the sampling instant can vary from device to device, but is typically within ±5 ns. This means that a maximum common input sine wave of ±2.5 V at 32 kHz, applied to any number of AD7821s in the circuit of Figure 22, will yield a maximum difference between the converter outputs of typically ±1/4 LSB. REV. B –13– AD7821 OUTLINE DIMENSIONS 20-Lead Plastic Dual-in-Line Package [PDIP] 20-Lead Ceramic DIP - Glass Hermetic Seal [CERDIP] (N-20) (Q-20) Dimensions shown in inches and (millimeters) Dimensions shown in inches and (millimeters) 0.985 (25.02) 0.005 0.098 (2.49) (0.13) MAX 0.310 (7.87) 0.965 (24.51) 0.295 (7.49) MIN 0.220 (5.59) 20 11 0.945 (24.00) 0.285 (7.24) PIN 1 0.275 (6.99) 20 11 110 1 10 0.060 (1.52) 0.325 (8.26) 0.320 (8.13) 0.200 (5.08) 0.015 (0.38) 1.060 (26.92) MAX 0.310 (7.87) MAX 0.290 (7.37) 0.150 (3.81) 0.150 (3.81) 0.300 (7.62) 0.180 (4.57) 0.015 (0.38) MIN MIN 0.135 (3.43) MAX 0.015 (0.38) 0.120 (3.05) 0.008 (0.20) 0.200 (5.08) 15 0.125 (3.18) 0 0.070 (1.78) SEATING 0.100 0.150 (3.81) PLANE (2.54) 0.023 (0.58) 0.030 (0.76) 0.130 (3.30) BSC 0.015 (0.38) 0.014 (0.36) 0.100 SEATING 0.060 (1.52) 0.110 (2.79) 0.022 (0.56) 0.010 (0.25) (2.54) PLANE CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETERS DIMENSIONS 0.050 (1.27) 0.018 (0.46) BSC 0.008 (0.20) (IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR 0.045 (1.14) 0.014 (0.36) REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN COMPLIANT TO JEDEC STANDARDS MO-095-AE CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN 20-Terminal Ceramic Leaded Chip Carrier [LCC] 20-Lead Standard Small Outline Package [SOIC] (E-20A) Wide Body Dimensions shown in millimeters and (inches) (RW-20) Dimensions shown in millimeters and (inches) 1.91 5.08 (0.2000) (0.0752) BSC 13.00 (0.5118) 2.54 (0.1000) REF 2.54 (0.1000) BSC 12.60 (0.4961) 1.63 (0.0642) 2.41 (0.0949) 0.38 (0.0150) 1.90 (0.0748) 19 3 MIN 20 11 20 18 4 0.71 (0.0278) 7.60 (0.2992) 1 9.09 (0.3579) 9.09 7.40 (0.2913) 0.28 (0.0110) 0.56 (0.0220) (0.3579) BOTTOM 8.69 (0.3421) 0.18 (0.0071) 10.65 (0.4193) MAX VIEW SQ 1.27 (0.0500) 1 R TYP 10 SQ 10.00 (0.3937) 14 8 BSC 1.91 (0.0752) 13 9 REF 45 TYP 2.24 (0.0882) 1.40 (0.0551) 2.65 (0.1043) 0.75 (0.0295) 3.81 (0.1500) � 45� 1.14 (0.0449) 2.35 (0.0925) 1.37 (0.0539) 0.25 (0.0098) BSC 0.30 (0.0118) 0.10 (0.0039) 8� 1.27 0.51 (0.0201) SEATING 0� 1.27 (0.0500) COPLANARITY 0.32 (0.0126) (0.0500) PLANE 0.33 (0.0130) 0.10 0.40 (0.0157) 0.23 (0.0091) BSC COMPLIANT TO JEDEC STANDARDS MS-013AC CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN –14– REV. B AD7821 OUTLINE DIMENSIONS 20-Lead Plastic Leaded Chip Carrier [PLCC] (P-20A) Dimensions shown in inches and (millimeters) 0.180 (4.57) 0.048 (1.21) 0.165 (4.19) 0.042 (1.07) 0.056 (1.42) 0.020 (0.50) 0.20 (0.51) 0.042 (1.07) MIN R 3 19 0.021 (0.53) 0.048 (1.21) 4 18 0.013 (0.33) 0.050 0.042 (1.07) 0.330 (8.38) BOTTOM (1.27) TOP VIEW VIEW 0.290 (7.37) BSC 0.032 (0.81) (PINS DOWN) (PINS UP) 0.026 (0.66) 8 14 9 13 0.020 0.040 (1.01) (0.50) 0.356 (9.04) R 0.025 (0.64) SQ 0.350 (8.89) 0.120 (3.04) 0.395 (10.02) 0.090 (2.29) SQ 0.385 (9.78) COMPLIANT TO JEDEC STANDARDS MO-047AA CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN Revision History Location Page 10/02—Data Sheet changed from REV. A to REV. B. Update Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Universal Changes to FUNCTIONAL BLOCK DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Edit to SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Change to TOTAL HARMONIC DISTORTION formula . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Changes to INPUT CURRENT section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Change to Figure 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Change to formula in SINUSOIDAL INPUTS section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 OUTLINE DIMENSIONS updated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 REV. B –15– –16– PRINTED IN U.S.A. C01320–0–11/02(B)

Frequently asked questions

What makes Elite.Parts unique?

chervon down
At GID Industrial (Elite.Parts' parent company), we specialize in procuring industrial parts. We know where to find the rare and obsolete equipment that our customers need in order to get back to business. There are other companies who claim to do what we do, but we're confident that our commitment to quality and value is unparalleled in our field.

What kind of warranty will the AD7821 have?

chervon down
Warranties differ by part and by which suppliers we use to procure it for you. Sometimes, a part will be sold as-is and without a warranty. Our specialty, single board computers, tend to receive a one-year warranty.

Which carriers does Elite.Parts work with?

chervon down
Elite.Parts can ship via FedEx, UPS, DHL, and USPS. We have accounts with each of them and generally ship using one of those, but we can also ship using your account if you would prefer. However, we can use other carriers if it will be more convenient for you.

Will Elite.Parts sell to me even though I live outside the USA?

chervon down
Absolutely! We are happy to serve customers regardless of location. We work with international clients all the time, and we are familiar with shipping to destinations all across the globe.

I have a preferred payment method. Will Elite.Parts accept it?

chervon down
All major credit cards are accepted: Visa, MasterCard, Discover, and American Express. We will also accept payment made with wire transfer or PayPal. Checks will only be accepted from customers in the USA. Terms may available for larger orders, upon approval.

Why buy from GID?

quality

Quality

We are industry veterans who take pride in our work

protection

Protection

Avoid the dangers of risky trading in the gray market

access

Access

Our network of suppliers is ready and at your disposal

savings

Savings

Maintain legacy systems to prevent costly downtime

speed

Speed

Time is of the essence, and we are respectful of yours

What they say about us

FANTASTIC RESOURCE

star star star star star

One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!

Bucher Emhart Glass

EXCELLENT SERVICE

star star star star star

With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.

Fuji

HARD TO FIND A BETTER PROVIDER

star star star star star

Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.

Applied Materials

CONSISTENTLY DELIVERS QUALITY SOLUTIONS

star star star star star

Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.

Nidec Vamco

TERRIFIC RESOURCE

star star star star star

This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.

Trican Well Service

GO TO SOURCE

star star star star star

When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.

ConAgra Foods

Related Products

ANALOG DEVICE# A5E1032

SOCKET FOR MODEL AD210 IC

TRANSFORMER CURRENT 60.0 AMP

SOCKET FOR MODEL 1B22 IC

product

Analog Devices AD7291 12-Bit Low power 8-Channel Successive Approximation Analog-to-Digital Converte...