ANALOG DEVICES AD7298-1
Description
Analog Devices AD7298-1 10-Bit High Speed Low Power 8 Channel Successive Approximation Analog-to-Digital Converter
Part Number
AD7298-1
Price
Request Quote
Manufacturer
ANALOG DEVICES
Lead Time
Request Quote
Category
PRODUCTS - A
Specifications
# Chan
8
ADC Architecture
SAR
Ain Range
Uni (Vref),Uni 1.0V,Uni 1.25,Uni 2.0V,Uni 2.5V
Analog Input Type
SE-Uni
Interface
SPI
Pkg Type
CSP
Resolution (Bits)
10bit
Sample Rate
1MSPS
Features
- 10-bit SAR ADC
- 20-lead LFCSP
- 8 single-ended inputs
- Analog input range: 0 V to 2.5 V
- Channel sequencer functionality
- Fast throughput of 1 MSPS
- High speed serial interface SPI
- Internal 2.5 V reference
- Internal power-on reset
- Logic voltage VDRIVE = 1.65 V to 3.6 V
- Power-down current:
- Specified for VDD of 2.8 V to 3.6 V
- Temperature range: -40°C to +125°C
Datasheet
Extracted Text
8-Channel, 1 MSPS, 10-Bit SAR ADC AD7298-1 FEATURES FUNCTIONAL BLOCK DIAGRAM V DD GND 10-bit SAR ADC 8 single-ended inputs V Channel sequencer functionality REF Fast throughput of 1 MSPS REF BUF Analog input range: 0 V to 2.5 V 10-BIT Temperature range: −40°C to +125°C V IN0 SUCCESSIVE T/H Specified for V of 2.8 V to 3.6 V APPROXIMATION DD ADC Logic voltage V = 1.65 V to 3.6 V DRIVE INPUT Power-down current: <10 µA AD7298-1 V MUX IN7 Internal 2.5 V reference SEQUENCER Internal power-on reset SCLK DOUT High speed serial interface SPI CONTROL DIN LOGIC 20-lead LFCSP CS V DRIVE PD/RST Figure 1. GENERAL DESCRIPTION The AD7298-1 is a 10-bit, high speed, low power, 8-channel, PRODUCT HIGHLIGHTS successive approximation ADC. The part operates from a single 1. Ideally Suited to Monitoring System Variables in a Variety 3.3 V power supply and features throughput rates up to 1 MSPS. of Systems. This includes telecommunications, and process The device contains a low noise, wide bandwidth track-and-hold and industrial control. amplifier that can handle input frequencies in excess of 30 MHz. 2. High Throughput Rate of 1 MSPS with Low Power The AD7298-1 offers a programmable sequencer, which enables Consumption. the selection of a preprogrammable sequence of channels for 3. Eight Single-Ended Inputs with a Channel Sequencer. A conversion. The device has an on-chip, 2.5 V reference that can consecutive sequence of channels can be selected on which be disabled to allow the use of an external reference. the ADC cycles and converts. The device offers a 4-wire serial interface compatible with SPI and DSP interface standards. The AD7298-1 uses advanced design techniques to achieve very low power dissipation at high throughput rates. The part also offers flexible power/throughput rate management options. The part is offered in a 20-lead LFCSP package. Rev. A Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. rights of third parties that may result from its use. Specifications subject to change without notice. No Tel: 781.329.4700 www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. Fax: 781.461.3113 ©2010–2011 Analog Devices, Inc. All rights reserved. 09321-001 AD7298-1 TABLE OF CONTENTS Features .............................................................................................. 1 Analog Input ............................................................................... 13 Functional Block Diagram .............................................................. 1 V ............................................................................................ 14 DRIVE General Description ......................................................................... 1 The Internal or External Reference .......................................... 14 Product Highlights ........................................................................... 1 Control Register .............................................................................. 15 Revision History ............................................................................... 2 Modes of Operation ....................................................................... 16 Specifications ..................................................................................... 3 Traditional Multichannel Mode of Operation ........................ 16 Timing Specifications .................................................................. 5 Repeat Operation ....................................................................... 17 Absolute Maximum Ratings ............................................................ 6 Power-Down Modes .................................................................. 18 Thermal Resistance ...................................................................... 6 Powering Up the AD7298-1 ...................................................... 19 ESD Caution .................................................................................. 6 Reset ............................................................................................. 19 Pin Configuration and Function Description .............................. 7 Serial Interface ................................................................................ 20 Typical Performance Characteristics ............................................. 9 Layout and Configuration ............................................................. 21 Terminology .................................................................................... 12 Outline Dimensions ....................................................................... 22 Circuit Information ........................................................................ 13 Ordering Guide .......................................................................... 22 Converter Operation .................................................................. 13 REVISION HISTORY 1/11—Rev. 0 to Rev. A Removed Input Impedance Parameter .......................................... 3 Added Input Capacitance Parameter of 8 pF ................................ 3 Changes to Figure 10 ...................................................................... 10 Changed C1 Value to 8 pF in Analog Input Section .................. 13 Changes to Figure 22 ...................................................................... 14 10/10—Revision 0: Initial Version Rev. A | Page 2 of 24 AD7298-1 SPECIFICATIONS VDD = 2.8 V to 3.6 V, VDRIVE = 1.65 V to 3.6 V, fSAMPLE = 1 MSPS, fSCLK = 20 MHz, VREF = 2.5 V internal, TA = −40°C to +125°C, unless otherwise noted. Table 1. Parameter Min Typ Max Unit Test Conditions/Comments DYNAMIC PERFORMANCE f = 50 kHz sine wave IN 1 Signal-to-Noise Ratio (SNR) 61 61.5 dB 2 Signal-to-Noise-(and-Distortion) Ratio (SINAD)61 61.5 dB 2 Total Harmonic Distortion (THD) −82 −75 dB Spurious-Free Dynamic Range (SFDR) −83 −76 dB Intermodulation Distortion (IMD) f = 40.1 kHz, f = 41.5 kHz A B Second-Order Terms −86 dB Third-Order Terms −86 dB Channel-to-Channel Isolation −90 dB fIN = 50 kHz, fNOISE = 60 kHz SAMPLE AND HOLD 3 Aperture Delay 12 ns 3 Aperture Jitter 40 ps Full Power Bandwidth 30 MHz At 3 dB 10 MHz At 0.1 dB DC ACCURACY Resolution 10 Bits 2 Integral Nonlinearity (INL) ±0.25 ±0.5 LSB 2 Differential Nonlinearity (DNL) ±0.3 ±0.5 LSB Guaranteed no missed codes to 10 bits 2 Offset Error ±0.5 ±1.125 LSB 2 Offset Error Matching ±0.625 ±1.125 LSB Offset Temperature Drift 4 ppm/°C 2 Gain Error ±0.25 ±1 LSB 2 Gain Error Matching ±0.16 ±0.625 LSB Gain Temperature Drift 0.5 ppm/°C ANALOG INPUT Input Voltage Ranges 0 V V REF DC Leakage Current ±0.01 ±1 μA Input Capacitance 32 pF When in track mode 8 pF When in hold mode REFERENCE INPUT/OUTPUT 4 Reference Output Voltage 2.4925 2.5 2.5075 V ±0.3% maximum at 25°C Long-Term Stability 150 ppm For 1000 hours Output Voltage Hysteresis 50 ppm Reference Input Voltage Range 1 2.5 V DC Leakage Current ±0.01 ±1 μA External reference applied to the V pin REF VREF Output Impedance 1 Ω VREF Temperature Coefficient 12 35 ppm/°C VREF Noise 60 μV rms Bandwidth = 10 MHz LOGIC INPUTS Input High Voltage, VINH 0.7 × VDRIVE V Input Low Voltage, V 0.3 × V V INL DRIVE Input Current, I ±0.01 ±1 μA V = 0 V or V IN IN DRIVE 3 Input Capacitance, C 3 pF IN Rev. A | Page 3 of 24 AD7298-1 Parameter Min Typ Max Unit Test Conditions/Comments LOGIC OUTPUTS Output High Voltage, VOH VDRIVE − 0.3 V VDRIVE < 1.8 VDRIVE − 0.2 V VDRIVE ≥ 1.8 Output Low Voltage, V 0.4 V OL Floating State Leakage Current ±0.01 ±1 μA 3 Floating State Output Capacitance 8 pF CONVERSION RATE Conversion Time 1 t + (16 × t ) μs For V to V with one cycle latency 2 SCLK IN0 IN7 2, 3 Track-and-Hold Acquisition Time 100 ns Full-scale step input Throughput Rate 1 MSPS fSCLK = 20 MHz; for analog voltage conversions, one cycle latency POWER REQUIREMENTS Digital inputs = 0 V or VDRIVE VDD 2.8 3 3.6 V VDRIVE 1.65 3 3.6 V 5 I V = 3.6 V, V = 3.6 V TOTAL DD DRIVE Normal Mode (Operational) 5.8 6.4 mA Normal Mode (Static) 4.1 4.6 mA Partial Power-Down Mode 2.7 3.3 mA Full Power-Down Mode 1 1.6 μA TA = −40°C to +25°C 10 μA TA = −40°C to +125°C 6 Power Dissipation Normal Mode (Operational) 17.4 19.2 mW V = 3 V, V = 3 V DD DRIVE 23 mW Normal Mode (Static) 14.8 16.6 mW Partial Power-Down Mode 9.8 11.9 mW Full Power-Down Mode 3.6 5.8 μW T = −40°C to +25°C A 36 μW T = −40°C to +125°C A 1 All specifications expressed in decibels are referred to full-scale input FSR and tested with an input signal at 0.5 dB below full scale, unless otherwise specified. 2 See the Terminology section. 3 Sample tested during initial release to ensure compliance. 4 Refers to the V pin specified for 25°C. REF 5 ITOTAL is the total current flowing in VDD and VDRIVE. 6 Power dissipation is specified with V = V = 3.6 V, unless otherwise noted. DD DRIVE Rev. A | Page 4 of 24 AD7298-1 TIMING SPECIFICATIONS V = 2.8 V to 3.6 V, V = 1.65 V to 3.6 V, V = 2.5 V internal, T = −40°C to +125°C, unless otherwise noted. Sample tested during DD DRIVE REF A initial release to ensure compliance. All input signals are specified with tr = tf = 5 ns (10% to 90% of V ) and timed from a voltage level DRIVE of 1.6 V. Table 2. Parameter Limit at T , T Unit Test Conditions/Comments MIN MAX t t + (16 × t ) µs max Conversion time CONVERT 2 SCLK 820 ns typ Each ADC channel V to V , f = 20 MHz IN0 IN7 SCLK 1 f 50 kHz min Frequency of external serial clock SCLK 20 MHz max Frequency of external serial clock t 6 ns min Minimum quiet time required between the end of the serial read and the start of QUIET the next voltage conversion in repeat and nonrepeat mode. t 10 ns min to SCLK setup time CS 2 1 t 15 ns max Delay from (falling edge) until DOUT three-state disabled CS 3 1 t Data access time after SCLK falling edge 4 35 ns max V = 1.65 V to 3 V DRIVE 28 ns max V = 3 V to 3.6 V DRIVE t 0.4 × t ns min SCLK low pulse width 5 SCLK t 0.4 × t ns min SCLK high pulse width 6 SCLK 1 t 14 ns min SCLK to DOUT valid hold time 7 1 t 16/34 ns min/ns max SCLK falling edge to DOUT high impedance 8 t 5 ns min DIN setup time prior to SCLK falling edge 9 t 4 ns min DIN hold time after SCLK falling edge 10 1 t 30 ns max Delay from CS rising edge to DOUT high impedance 11 t 6 ms max Internal reference power-up time from full power-down POWER-UP 1 Measured with a load capacitance on DOUT of 15 pF. Rev. A | Page 5 of 24 AD7298-1 ABSOLUTE MAXIMUM RATINGS THERMAL RESISTANCE Table 3. Table 4. Thermal Resistance Parameter Rating Package Type θ θ Unit JA JC V to GND, GND1 −0.3 V to +5 V 20-Lead LFCSP 52 6.5 °C/W DD V to GND, GND1 −0.3 V to + 5 V DRIVE Analog Input Voltage to GND1 −0.3 V to +3 V ESD CAUTION Digital Input Voltage to GND −0.3 V to V + 0.3 V DRIVE Digital Output Voltage to GND −0.3 V to V + 0.3 V DRIVE V to GND1 −0.3 V to +3 V REF AGND to GND −0.3 V to +0.3 V Input Current to Any Pin Except Supplies ±10 mA Operating Temperature Range −40°C to +125°C Storage Temperature Range −65°C to +150°C Junction Temperature 150°C Pb-free Temperature, Soldering Reflow 260(0)°C ESD 3.5 kV Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Rev. A | Page 6 of 24 AD7298-1 PIN CONFIGURATION AND FUNCTION DESCRIPTION 15 SCLK V 1 IN3 14 DOUT V 2 IN4 AD7298-1 V 3 13 DIN IN5 TOP VIEW (Not to Scale) NC V 4 12 IN6 5 11 CS V IN7 NOTES 1. NC = NO CONNECT. 2. THE EXPOSED METAL PADDLE ON THE BOTTOM OF THE LFCSP PACKAGE SHOULD BE SOLDERED TO PCB GROUND FOR PROPER FUNCTIONALITY AND HEAT DISSIPATION. Figure 2. Pin Configuration Table 5. Pin Function Descriptions Pin No. Mnemonic Description 1 to 5, V , V Analog Inputs. The AD7298-1 has eight single-ended analog inputs that are multiplexed into the on-chip track- IN3 IN4 18 to 20 V , V , and-hold. Each input channel can accept analog inputs from 0 V to 2.5 V. Any unused input channels should be IN5 IN6 V , V , connected to GND1 to avoid noise pickup. IN7 IN0 V , V IN1 IN2 6 GND1 Ground. Ground reference point for the internal reference circuitry on the AD7298-1. The external reference signals and all analog input signals should be referred to the GND1 voltage. The GND1 pin should be connected to the ground plane of a system. All ground pins should ideally be at the same potential and must not be more than 0.3 V apart, even on a transient basis. The V pin should be decoupled to this ground pin via a 10 µF REF decoupling capacitor. 7 V Internal Reference/External Reference Supply. The nominal internal reference voltage of 2.5 V appears at this pin. REF Provided the output is buffered, the on-chip reference can be taken from this pin and applied externally to the rest of a system. Decoupling capacitors should be connected to this pin to decouple the reference buffer. For best performance, it is recommended to use a 10 µF decoupling capacitor on this pin to GND1. The internal reference can be disabled and an external reference supplied to this pin, if required. The input voltage range for the external reference is 2.0 V to 2.5 V. 8 D Decoupling Capacitor Pins. Decoupling capacitors (1 µF recommended) are connected to this pin to decouple CAP the internal LDO. 9 GND Ground. Ground reference point for all analog and digital circuitry on the AD7298-1. The GND pin should be connected to the ground plane of the system. All ground pins should ideally be at the same potential and must not be more than 0.3 V apart, even on a transient basis. Both the D and V pins should be decoupled to this CAP DD GND pin. 10 V Supply Voltage, 2.8 V to 3.6 V. This supply should be decoupled to GND with 10 µF and 100 nF decoupling capacitors. DD 11 CS Chip Select, Active Low Logic Input. This pin is edge triggered on the falling edge of this input, the track-and- hold goes into hold mode, and a conversion is initiated. This input also frames the serial data transfer. When CS is low, the output bus is enabled and the conversion result becomes available on the DOUT output. 12 NC No Connect. 13 D Data In, Logic Input. Data to be written to the AD7298-1 control register is provided on this input and is clocked IN into the register on the falling edge of SCLK. 14 DOUT Serial Data Output. The conversion result from the AD7298-1 is provided on this output as a serial data stream. The bits are clocked out on the falling edge of the SCLK input. The data stream from the AD7298-1 consists of four address bits indicating which channel the conversion result corresponds to, followed by the 10 bits of conversion data (MSB first). 15 SCLK Serial Clock, Logic Input. A serial clock input provides the SCLK for accessing the data from the AD7298-1. Rev. A | Page 7 of 24 09321-003 GND1 6 20 V N2 I V 19 REF 7 V IN1 D 8 18 V CAP IN0 17 PD/RST GND 9 V 10 16 V DD DRIVE AD7298-1 Pin No. Mnemonic Description 16 V Logic Power Supply Input. The voltage supplied at this pin determines the voltage at which the interface DRIVE operates. This pin should be decoupled to ground. The voltage range on this pin is 1.65 V to 3.6 V and may be less than the voltage at V but should never exceed it by more than 0.3 V. DD 17 PD/RST Power-Down Pin. This pin places the part into full power-down mode and enables power conservation when operation is not required. This pin can be used to reset the device by toggling the pin low for a minimum of 1 ns and a maximum of 100 ns. If the maximum time is exceeded, the part enters power-down mode. When placing the AD7298-1 into full power-down mode, the analog inputs must return to 0 V. EPAD The exposed metal paddle on the bottom of the LFCSP package should be soldered to PCB ground for proper functionality and heat dissipation. Rev. A | Page 8 of 24 AD7298-1 TYPICAL PERFORMANCE CHARACTERISTICS 0 0.50 V = V = 3V DD DRIVE f = 1.17647MHz –10 SAMPLE 0.40 f = 50kHz IN –20 f = 20MHz SCLK 0.30 SNR = 61.83dB –30 THD = –80.23dB INL (Positive) 0.20 –40 0.10 –50 0 –60 INL (Negative) –0.10 –70 –0.20 –80 –0.30 –90 –0.40 –100 –0.50 –110 0 100 200 300 400 500 600 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 2.6 V (V) FREQUENCY (MHz) REF Figure 3. Typical FFT Figure 6. INL vs. V REF 1.0 0.50 V = 3V DD V = 3V 0.8 DRIVE 0.40 INL (Positive) 0.6 0.30 0.4 0.20 0.2 0.10 0 0 0.2 –0.10 INL (Negative) 0.4 –0.20 –0.6 –0.30 –0.8 –0.40 –1.0 –0.50 1 101 201 301 401 501 601 701 801 901 1001 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 2.6 CODE V (V) REF Figure 4. Typical ADC INL Figure 7. DNL vs. V REF 1.0 11 V = 3V DD 0.8 V = 3V DRIVE 10 0.6 9 0.4 8 0.2 7 0 6 0.2 5 –0.4 4 –0.6 3 V = 3V –0.8 DD V = 3V DRIVE –1.0 2 1 101 201 301 401 501 601 701 801 901 1001 0 0.5 1.0 1.5 2.0 2.5 CODE EXTERNAL VOLTAGE REFERENCE (V) Figure 5. Typical ADC DNL Figure 8. Effective Number of Bits vs. V REF Rev. A | Page 9 of 24 DNL (LSB) SIGNAL POWER (dB) INL (LSB) 09321-040 09321-047 09321-041 DNL (LSB) EFFECTIVE NUMBER OF BITS INL (LSB) 09321-042 09321-038 09321-039 AD7298-1 62.0 3.0 V = 3V V = V = 3V DD DD DRIVE V = 3V DRIVE 61.5 61.0 2.5 60.5 2.0 60.0 59.5 1.5 59.0 R = 0Ω SOURCE R = 10Ω SOURCE R = 33Ω SOURCE 58.5 R = 47Ω SOURCE R = 100Ω SOURCE R = 200Ω SOURCE 1.0 58.0 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 10 100 CURRENT LOAD (mA) INPUT FREQUENCY (kHz) Figure 9. V vs. Reference Output Current Drive Figure 12. SINAD vs. Analog Input Frequency for Various Source Impedances REF –90 62.00 V = 3V DD V = 3V DD V = 3V DRIVE V = 3V –92 DRIVE 61.75 –94 –96 61.50 –98 –100 61.25 –102 61.00 –104 –106 60.75 –108 60.50 –110 1.0 1.5 2.0 2.5 1k 10k 100k 1M 10M 100M EXTERNAL REFERENCE VOLTAGE (V) RIPPLE FREQUENCY (Hz) Figure 10. PSRR vs. Supply Ripple Frequency Without Supply Decoupling Figure 13. SINAD vs. Reference Voltage –80 110 V = 3V DD V = 3V –81 DRIVE 105 –82 100 –83 95 –84 –85 90 –86 85 –87 80 –88 75 –89 –90 70 1.0 1.5 2.0 2.5 0 50 100 150 200 250 300 350 400 450 500 550 EXTERNAL REFERENCE VOLTAGE (V) f (kHz) NOISE Figure 14. THD vs. Reference Voltage Figure 11. Channel-to-Channel Isolation, f = 50 kHz IN Rev. A | Page 10 of 24 PSRR (dB) ISOLATION (dB) V (V) REF 09321-111 09321-109 09321-110 SINAD (dB) THD (dB) SINAD (dB) 09321-046 09321-044 09321-043 AD7298-1 –60 19 R = 0Ω SOURCE V = V = 3V DD DRIVE R = 10Ω SOURCE R = 33Ω 18 SOURCE R = 47Ω –65 SOURCE R = 100Ω SOURCE 17 R = 200Ω SOURCE –70 16 15 –75 14 –80 13 12 –85 11 V = 3V DD V = 3V DRIVE –90 10 10 100 0 100 200 300 400 500 600 700 800 900 1000 INPUT FREQUENCY (kHz) THROUGHPUT (kSPS) Figure 15. THD vs. Analog Input Frequency for Various Source Impedances Figure 17. Power vs. Throughput in Normal Mode with V = 3 V DD 6 4.0 V = 3V V = V = 3V –40°C +85°C DRIVE DD DRIVE 0°C +105°C 3.5 +25°C +125°C 5 3.0 V CURRENT DD 4 2.5 3 2.0 1.5 2 1.0 1 V CURRENT DRIVE 0.5 0 0 0 200 400 600 800 1000 1200 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 THROUGHPUT (kSPS) V (V) DD Figure 16. Average Supply Current vs. Throughput Rate Figure 18. Full Shutdown Current vs. Supply Voltage for Various Temperatures Rev. A | Page 11 of 24 CURRENT (mA) THD (dB) 09321-045 09321-114 POWER (mW) TOTAL CURRENT (µA) 09321-119 09321-118 AD7298-1 TERMINOLOGY Differential Nonlinearity Signal-to-Noise-and-Distortion Ratio (SINAD) The difference between the measured and the ideal 1 LSB The measured ratio of signal-to-noise and distortion at the change between any two adjacent codes in the ADC. output of the ADC. The signal is the rms amplitude of the fundamental. Noise is the sum of all nonfundamental signals up Offset Error to half the sampling frequency (f /2), excluding dc. The ratio is The deviation of the first code transition (00…000) to S dependent on the number of quantization levels in the digitization (00…001) from the ideal—that is, GND1 + 1 LSB. process; the more levels, the smaller the quantization noise. The Offset Error Matching theoretical signal-to-noise-and-distortion ratio for an ideal N- The difference in offset error between any two channels. bit converter with a sine wave input is given by Gain Error Signal-to-(Noise + Distortion) = (6.02 N + 1.76) dB The deviation of the last code transition (111…110) to Thus, the SINAD is 61.96 dB for an ideal 10-bit converter. (111…111) from the ideal (that is, V − 1 LSB) after the offset REF error has been adjusted out. Total Harmonic Distortion (THD) The ratio of the rms sum of harmonics to the fundamental. For Gain Error Matching the AD7298-1, it is defined as The difference in gain error between any two channels. Track-and-Hold Acquisition Time 2 2 2 2 2 V +V +V +V +V 2 3 4 5 6 THD(dB)= 20 log The track-and-hold amplifier returns to track mode at the end V 1 of the conversion. The track-and-hold acquisition time is the where: time required for the output of the track-and-hold amplifier to V is the rms amplitude of the fundamental. reach its final value, within ±1 LSB, after the end of the conversion. 1 V , V , V , V , and V are the rms amplitudes of the second 2 3 4 5 6 Power Supply Rejection Ratio (PSRR) through sixth harmonics. PSRR is defined as the ratio of the power in the ADC output at Peak Harmonic or Spurious Noise full-scale frequency, f, to the power of a 100 mV p-p sine wave The ratio of the rms value of the next largest component in the applied to the ADC V supply of frequency, f . The frequency DD S ADC output spectrum (up to f /2 and excluding dc) to the rms of the input varies from 5 kHz to 25 MHz. S value of the fundamental. Typically, the value of this specification PSRR (dB) = 10 log(Pf/Pf ) S is determined by the largest harmonic in the spectrum, but for where: ADCs where the harmonics are buried in the noise floor, it is a Pf is the power at frequency, f, in the ADC output. noise peak. Pf is the power at frequency, f , in the ADC output. S S Integral Nonlinearity The maximum deviation from a straight line passing through the endpoints of the ADC transfer function. The endpoints are zero scale, a point 1 LSB below the first code transition, and full scale, a point 1 LSB above the last code transition. Rev. A | Page 12 of 24 AD7298-1 CIRCUIT INFORMATION The AD7298-1 is a high speed, 8-channel, 10-bit ADC. The part CAPACITIVE DAC can be operated from a 2.8 V to 3.6 V supply and is capable of throughput rates of 1 MSPS per analog input channel. A V IN CONTROL SW1 The AD7298-1 provides the user with an on-chip, track-and-hold B LOGIC SW2 ADC and a serial interface housed in a 20-lead LFCSP. The COMPARATOR GND1 AD7298-1 has eight, single-ended input channels with channel Figure 20. ADC Conversion Phase repeat functionality, which allows the user to select a channel sequence through which the ADC can cycle with each consecutive ANALOG INPUT CS falling edge. The serial clock input accesses data from the Figure 21 shows an equivalent circuit of the analog input structure part, controls the transfer of data written to the ADC, and of the AD7298-1. The two diodes, D1 and D2, provide ESD provides the clock source for the successive approximation protection for the analog inputs. Care must be taken to ensure ADC. The analog input range for the AD7928-1 is 0 V to V . REF that the analog input signal never exceeds the internally generated The AD7298-1 operates with one cycle latency, which means LDO voltage of 2.5 V (DCAP) by more than 300 mV. This causes that the conversion result is available in the serial transfer the diodes to become forward-biased and to start conducting following the cycle in which the conversion is performed. current into the substrate. The maximum current these diodes can conduct without causing irreversible damage to the part is The AD7298-1 provides flexible power management options to 10 mA. Capacitor C1, in Figure 21, is typically about 8 pF and allow the user to achieve the best power performance for a given can primarily be attributed to pin capacitance. The R1 resistor is throughput rate. These options are selected by programming a lumped component made up of the on resistance of a switch the partial power-down bit, PPD, in the control register and (track-and-hold switch) and includes the on resistance of the using the / pin. PD RST input multiplexer. The total resistance is typically about 155 Ω. CONVERTER OPERATION The capacitor, C2, is the ADC sampling capacitor and has a The AD7298-1 is a 10-bit successive approximation ADC based capacitance of 34 pF typically. around a capacitive DAC. Figure 19 and Figure 20 show simplified D (2.5V) CAP schematics of the ADC. The ADC is comprised of control logic, C2 SAR, and a capacitive DAC that are used to add and subtract D1 pF R1 fixed amounts of charge from the sampling capacitor to bring V IN the comparator back into a balanced condition. Figure 19 shows D2 CONVERSION PHASE: SWITCH OPEN C1 TRACK PHASE: SWITCH CLOSED pF the ADC during its acquisition phase. SW2 is closed and SW1 is in Position A. The comparator is held in a balanced condition and the sampling capacitor acquires the signal on the selected Figure 21. Equivalent Analog Input Circuit VIN channel. For ac applications, removing high frequency components from CAPACITIVE DAC the analog input signal is recommended by using an RC low-pass filter on the relevant analog input pin. In applications where A V IN harmonic distortion and signal-to-noise ratios are critical, the CONTROL SW1 B LOGIC SW2 analog input should be driven from a low impedance source. Large COMPARATOR GND1 source impedances significantly affect the ac performance of the Figure 19. ADC Acquisition Phase ADC. This may necessitate the use of an input buffer amplifier. The choice of the op amp is a function of the particular application When the ADC starts a conversion (see Figure 20), SW2 opens performance criteria. and SW1 moves to Position B, causing the comparator to become unbalanced. The control logic and the capacitive DAC are used to add and subtract fixed amounts of charge to bring the comparator back into a balanced condition. When the comparator is rebalanced, the conversion is complete. The control logic generates the ADC output code. Figure 22 shows the transfer function of the ADC. Rev. A | Page 13 of 24 08754-004 09321-006 09321-005 AD7298-1 ADC Transfer Function This enables the AD7298-1 to operate with a larger dynamic range with a V of 3.3 V while still being able to interface to DD The output coding of the AD7298-1 is straight binary for the 1.8 V processors. Take care to ensure V does not exceed DRIVE analog input channel conversion results. The designed code V by more than 0.3 V (see the Absolute Maximum Ratings DD transitions occur at successive LSB values (that is, 1 LSB, 2 LSBs, section). and so forth). The LSB size is V /1024 for the AD7298-1. The REF ideal transfer characteristic for the AD7298-1 for straight binary THE INTERNAL OR EXTERNAL REFERENCE coding is shown in Figure 22. The AD7298-1 can operate with either the internal 2.5 V on-chip reference or an externally applied reference. The EXT_REF bit in the control register is used to determine whether the internal 111...111 111...110 reference is used. If the EXT_REF bit is selected in the control register, an external reference can be supplied through the V REF pin. At power-up, the internal reference is enabled. Suitable 111...000 external reference sources for the AD7298-1 include AD780, 011...111 1LSB = V /1024 AD1582, ADR431, REF193, and ADR391. REF The internal reference circuitry consists of a 2.5 V band gap reference and a reference buffer. When the AD7298-1 is operated 000...010 000...001 in internal reference mode, the 2.5 V internal reference is 000...000 available at the V pin, which should be decoupled to GND1 0V REF 1LSB +V – 1LSB REF using a 10 µF capacitor. It is recommended that the internal ANALOG INPUT NOTES reference be buffered before applying it elsewhere in the system. 1. V IS 2.5V. REF The internal reference is capable of sourcing up to 2 mA of current Figure 22. Straight Binary Transfer Characteristic when the converter is static. The reference buffer requires 5.5 ms to V DRIVE power up and charge the 10 µF decoupling capacitor during the power-up time. The AD7298-1 also provides the V feature. V controls DRIVE DRIVE the voltage at which the serial interface operates. V allows DRIVE the ADC to easily interface to both 1.8 V and 3 V processors. For example, if the AD7298-1 were operated with a V of DD 3.3 V, the V pin could be powered from a 1.8 V supply. DRIVE Rev. A | Page 14 of 24 ADC CODE 09321-007 AD7298-1 CONTROL REGISTER The control register of the AD7298-1 is a 16-bit, write-only 16 serial clocks for every data transfer. Only the information register. Data is loaded from the DIN pin of the AD7298-1 on provided on the first 16 falling clock edges (after the falling the falling edge of SCLK. The data is transferred on the DIN edge of CS) is loaded to the control register. MSB denotes the line at the same time that the conversion result is read from the first bit in the data stream. The bit functions are outlined in part. The data transferred on the DIN line corresponds to the Table 6 and Table 7. At power-up, the default content of the AD7298-1 configuration for the next conversion. This requires control register is all zeros. Table 6. Control Register Bit Functions MSB LSB D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 WRITE REPEAT CH0 CH1 CH2 CH3 CH4 CH5 CH6 CH7 0 DONTC DONTC EXT_REF DONTC PPD Table 7. Control Register Bit Function Description Bit Mnemonic Description D15 WRITE The value written to this bit determines whether the subsequent 15 bits are loaded to the control register. If this bit is a 1, the following 15 bits are written to the control register. If this bit is a 0, then the remaining 15 bits are not loaded to the control register, and it remains unchanged. D14 REPEAT This bit enables the repeated conversion of the selected sequence of channels. D13 to CH0 to These eight channel selection bits are loaded at the end of the current conversion and select which analog input D6 CH7 channel is to be converted in the next serial transfer, or they can select the sequence of channels for conversion in the subsequent serial transfers. Each CHx bit corresponds to an analog input channel. A channel or sequence of channels is selected for conversion by writing a 1 to the appropriate CHx bit/bits. Channel address bits corresponding to the conversion result are output on DOUT prior to the 10 bits of data. The next channel to be th converted is selected by the mux on the 14 SCLK falling edge. D5 0 Zero should be written to this bit. D4, D3, DONTC Don’t care. D1 D2 EXT_REF Writing Logic 1 to this bit, enables the use of an external reference. The input voltage range for the external reference is 1 V to 2.5 V. The external reference should not exceed 2.5 V or the device performance is affected. D0 PPD This partial power-down mode is selected by writing a 1 to this bit in the control register. In this mode, some of the internal analog circuitry is powered down. The AD7298-1 retains the information in the control register while in partial power-down mode. The part remains in this mode until a 0 is written to this bit. Table 8. Channel Address Bits ADD3 ADD2 ADD1 ADD0 Analog Input Channel 0 0 0 0 V IN0 0 0 0 1 V IN1 0 0 1 0 V IN2 0 0 1 1 V IN3 0 1 0 0 V IN4 0 1 0 1 V IN5 0 1 1 0 V IN6 0 1 1 1 V IN7 Rev. A | Page 15 of 24 AD7298-1 MODES OF OPERATION subsequent (second) falling edge; and the third falling edge The AD7298-1 offers different modes of operation that are CS CS designed to provide additional flexibility for the user. These will have the result (V ) available for reading. The AD7298-1 IN2 options can be chosen by programming the content of the operates with one cycle latency, therefore the conversion result control register to select the desired mode. corresponding to each conversion is available one serial read cycle after the cycle in which the conversion was initiated. TRADITIONAL MULTICHANNEL MODE OF OPERATION As the device operates with one cycle latency, the control register configuration sets up the configuration for the next The AD7298-1 can operate as a traditional multichannel ADC, conversion, which is initiated on the next CS falling edge, but where each serial transfer selects the next channel for conversion. the first bit of the corresponding result is not clocked out until One must write to the control register to configure and select the subsequent falling edge, as shown in Figure 23. CS the desired input channel prior to initiating any conversions. In the traditional mode of operation, the CS signal is used to frame If more than one channel is selected in the control register, the the first write to the converter on the DIN pin. In this mode of AD7298-1 converts all selected channels sequentially in ascending operation, the REPEAT bit in the control register is set to a low order on successive falling edges. Once all the selected channels CS logic level (0), therefore the REPEAT function is not in use. The in the control register are converted, the AD7298-1 ceases converting data, which appears on the DOUT pin during the initial write to until the user rewrites to the control register to select the next the control register, is invalid. The first CS falling edge initiates a channel for conversion. This operation is shown in Figure 24. write to the control register to configure the device; a conversion is DOUT returns all 1s if the sequence of conversions is completed or then initiated for the selected analog input channel (V ) on the if no channel is selected. IN0 CS 1 10 16 1 16 1 16 1 16 SCLK CONVERSION RESULT CONVERSION RESULT INVALID DATA INVALID DATA DOUT FOR CHANNEL 1 FOR CHANNEL 4 DATA WRITTEN TO CONTROL DATA WRITTEN TO CONTROL NO WRITE TO THE NO WRITE TO THE DIN REGISTER CHANNEL 1 SELECTED REGISTER CHANNEL 4 SELECTED CONTROL REGISTER CONTROL REGISTER Figure 23. Configuring a Conversion and Read with the AD7298-1, One Channel Selected for Conversion CS 1 10 16 1 16 1 16 SCLK CONVERSION RESULT INVALID DATA INVALID DATA DOUT FOR CHANNEL 1 DATA WRITTEN TO CONTROL NO WRITE TO THE DATA WRITTEN TO CONTROL DIN REGISTER CH 1 AND 2 SELECTED CONTROL REGISTER REGISTER CHANNEL 5 SELECTED CS 1 16 1 16 SCLK CONVERSION RESULT CONVERSION RESULT DOUT FOR CHANNEL 2 FOR CHANNEL 5 NO WRITE TO THE NO WRITE TO THE DIN CONTROL REGISTER CONTROL REGISTER Figure 24. Configuring a Conversion and Read with the AD7298-1, Numerous Channels Selected for Conversion Rev. A | Page 16 of 24 09321-010 09321-009 AD7298-1 CS 1 10 16 1 16 1 16 SCLK CONVERSION RESULT INVALID DATA INVALID DATA DOUT FOR CHANNEL 0 NO WRITE TO THE NO WRITE TO THE DIN CONTROL REGISTER CONTROL REGISTER DATA WRITTEN TO CONTROL REGISTER CH0, CH1, AND CH2 SELECTED: REPEAT = 1 CS 1 16 1 16 1 16 SCLK CONVERSION RESULT CONVERSION RESULT CONVERSION RESULT DOUT FOR CHANNEL 1 FOR CHANNEL 2 FOR CHANNEL 0 NO WRITE TO THE NO WRITE TO THE NO WRITE TO THE DIN CONTROL REGISTER CONTROL REGISTER CONTROL REGISTER Figure 25. Configuring a Conversion and Read in Repeat Mode REPEAT OPERATION The REPEAT bit in the control register allows the user to select To select a sequence of channels, the associated channel bit a sequence of channels on which the AD7298-1 continuously must be set to a logic high state (1) for each analog input whose converts. When the REPEAT bit is set in the control register, the conversion is required. For example, if the REPEAT bit = 1, then AD7298-1 continuously cycles through the selected channels in CH0, CH1, and CH2 = 1. The V analog input is converted on IN0 the first falling edge following the write to the control register, ascending order, beginning with the lowest channel and converting CS all channels selected in the control register. On completion of the V channel is converted on the subsequent CS falling edge, IN1 the sequence, the AD7298-1 returns to the first selected channel and the V conversion result is available for reading. The third IN0 in the control register and recommences the sequence. CS falling edge following the write operation initiates a conversion The conversion sequence of the selected channels in the repeat on V and has the V result available for reading. The AD7298-1 IN2 IN1 mode of operation continues until the control register of the operates with one cycle latency, therefore the conversion result AD7298-1 is reprogrammed. It is not necessary to write to the corresponding to each conversion is available one serial read control register once a repeat operation is initiated unless a change cycle after the cycle in which the conversion is initiated. in the AD7298-1 configuration is required. The WRITE bit This mode of operation simplifies the operation of the device by must be set to zero, or the DIN line tied low to ensure that the allowing consecutive channels to be converted without having control register is not accidentally overwritten or the automatic to reprogram the control register or write to the part on each conversion sequence interrupted. serial transfer. Figure 25 illustrates how to set up the AD7298-1 A write to the control register during the repeat mode of operation to continuously convert on a particular sequence of channels. resets the cycle even if the selected channels are unchanged. To exit the repeat mode of operation and revert to the traditional Thus, the next conversion by the AD7298-1 after a write mode of operation of a multichannel ADC, ensure that the operation will be the first selected channel in the sequence. REPEAT bit = 0 on the next serial write. Rev. A | Page 17 of 24 09321-011 AD7298-1 Partial Power-Down Mode POWER-DOWN MODES In this mode, part of the internal circuitry on the AD7298-1 The AD7298-1 has a number of power conservation modes of is powered down. The AD7298-1 enters partial power-down operation that are designed to provide flexible power management on the CS rising edge once the current serial write operation options. These options can be chosen to optimize the power dissipation/throughput rate ratio for different application containing 16 SCLK clock cycles is completed. To enter partial requirements. The power-down modes of operation of the power-down, the PPD bit in the control register should be set to AD7298-1 are controlled by the power-down (PPD) bit in the 1 on the last required read transfer from the AD7298-1. Once in control register and the PD/RST pin on the device. When power partial power-down mode, the AD7298-1 transmits all 1s on the DOUT pin if CS is toggled low. supplies are first applied to the AD7298-1, care should be taken to ensure that the part is placed in the required mode of operation. The AD7298-1 remains in partial power-down until the power- Normal Mode down bit, PPD, in the control register is changed to Logic Level 0. The AD7298-1 begins powering up on the rising edge of CS Normal mode is intended for the fastest throughput rate following the write to the control register disabling the power- performance because the user does not have to be concerned down bit. Once t has elapsed, a full 16 SCLK writes to the about any power-up times since the AD7298-1 remains fully QUIET control register must be completed to update its content with powered on at all times. Figure 26 shows the general diagram the desired channel configuration for the subsequent conversion. of the normal mode operation of the AD7298-1. The conversion A valid conversion is then initiated on the next CS falling edge. is initiated on the falling edge of and the track-and-hold enters CS th hold mode. On the 14 SCLK falling edge, the track-and-hold Because the AD7298-1 has one cycle latency, the first conversion returns to track mode and starts acquiring the analog input, as result after exiting partial power-down mode is available in the described in the Serial Interface section. The data presented to fourth serial transfer, as shown in Figure 27. The first cycle updates the AD7298-1 on the DIN line during the first 16 clock cycles of the PPD bit, the second cycle updates the configuration and the data transfer are loaded into the control register (provided the Channel ID bits, the third completes the conversion, and the WRITE bit is 1). The part remains fully powered up in normal fourth accesses the DOUT valid result. The use of this mode mode at the end of the conversion as long as the PPD bit is set enables a reduction in the overall power consumption of the device. to 0 in the write transfer during that conversion. Full Power-Down Mode To ensure continued operation in normal mode, the PPD bit In this mode, all internal circuitry on the AD7298-1 is powered should be loaded with 0 on every data write operation. Sixteen down, and no information is retained in the control register or any serial clock cycles are required to complete the conversion and other internal register. access the conversion result. For specified performance, the The AD7298-1 is placed into full power-down mode by bringing throughput rate should not exceed 1 MSPS. When a conversion PD/RST pin low for greater than 100 ns. the logic level on the is complete and the has returned high, a minimum of the quiet CS When placing the AD7298-1 in full power-down mode, the ADC time, t , must elapse before bringing CS low again to initiate QUIET PD RST inputs must return to 0 V. The / pin is asynchronous to the another conversion and access the previous conversion result. clock; therefore, it can be triggered at any time. The part can be CS powered up for normal operation by bringing the PD/RST pin 1 16 logic level back to a high logic state. SCLK 4 CHANNEL ADDRESS BITS The full power-down feature can be used to reduce the average DOUT + CONVERSION RESULT power consumed by the AD7298-1 when operating at lower DATA WRITTEN TO CONTROL DIN throughput rates. The user should ensure that t has REGISTER IF REQUIRED POWER-UP elapsed prior to programming the control register and initiating Figure 26. Normal Mode Operation a valid conversion. THE PART IS FULLY PART IS IN PART BEGINS TO POWERED UP ONCE THE PARTIAL POWER UP ON CS WRITE TO THE CONTROL POWER DOWN RISING EDGE. REGISTER IS COMPLETED. t QUIET t QUIET CS 1 10 16 1 16 1 16 SCLK INVALID DATA INVALID DATA DOUT WRITE TO CONTROL WRITE TO THE CONTROL NO WRITE TO DIN REGISTER, PPD = 0. REGISTER, SELECT CH1, PPD = 0 CONTROL REGISTER CONTROL REGISTER CONFIGURED SELECT ANALOG INPUT CHANNELS AD7298 CONVERTING CHANNEL 1 TO POWER UP DEVICE. FOR CONVERSION. THE NEXT CYCLE NEXT CYCLE HAS CHANNEL 1 WILL CONVERT THE FIRST CHANNEL RESULT AVAILABLE FOR READING. PROGRAMMED IN THIS WRITE OPERATION. Figure 27. Partial Power-Down Mode of Operation Rev. A | Page 18 of 24 09321-012 09321-213 AD7298-1 POWERING UP THE AD7298-1 RESET The AD7298-1 contains a power-on reset circuit that sets the The AD7298-1 includes a reset feature that can be used to reset control register to its default setting of all zeros; therefore, the the device and the contents of all internal registers, including internal reference is enabled and the device is configured for the the control register, to their default state. normal mode of operation. At power-up, the internal reference is PD RST To activate the reset operation, the / pin should be brought by default enabled, which takes up to 6 ms (maximum) to power up. low for no longer than 100 ns. It is asynchronous with the clock; If an external reference is being used, the user does not need to therefore, it can be triggered at any time. If the PD/RST pin is wait for the internal reference to power up fully. The AD7298-1 held low for greater than 100 ns, the part enters full power-down digital interface is fully functional after 500 µs from the initial mode. It is imperative that the PD/RST pin be held at a stable power-up. Therefore, the user can write to the control register logic level at all times to ensure normal operation. after 500 µs to switch to external reference mode. The AD7298-1 is then immediately ready to convert once the external reference is available on the V pin. REF When supplies are first applied to the AD7298-1, the user must wait the specified 500 µs before programming the control register to select the desired channels for conversion. Rev. A | Page 19 of 24 AD7298-1 SERIAL INTERFACE When goes low, it provides the first address bit to be read in Figure 28 shows the detailed timing diagram for the serial interface CS to the AD7298-1. The serial clock provides the conversion clock by the microcontroller or DSP. The remaining data is then clocked and controls the transfer of information to and from the AD7298-1 out by subsequent SCLK falling edges, beginning with a second during each conversion. address bit. Thus, the first falling clock edge on the serial clock has the first address bit provided for reading and also clocks out The signal initiates the data transfer and conversion process. CS the second address bit. The three remaining address bits and 12 puts the track-and-hold into hold mode The falling edge of CS data bits are clocked out by subsequent SCLK falling edges. The at which point the analog input is sampled and the bus is taken th final bit in the data transfer is valid for reading on the 16 falling out of three-state. The conversion is also initiated at this point th edge having been clocked out on the previous (15 ) falling edge. and requires 16 SCLK cycles to complete. The track-and-hold th In applications with a slower SCLK, it may be possible to read in goes back into track mode on the 14 SCLK falling edge as shown th data on each SCLK rising edge depending on the SCLK frequency. in Figure 28 at Point B. On the 16 SCLK falling edge or on the The first rising edge of SCLK after the falling edge would CS rising edge of CS, the DOUT line goes back into three-state. th have the first address bit provided, and the 15 rising SCLK If the rising edge of occurs before 16 SCLKs have elapsed, CS edge would have last data bit provided. the conversion is terminated, the DOUT line goes back into Writing information to the control register takes place on the three-state, and the control register is not updated; otherwise, th first 16 falling edges of SCLK in a data transfer, assuming the DOUT returns to three-state on the 16 SCLK falling edge. MSB (that is, the WRITE bit) has been set to 1. The 16-bit word Sixteen serial clock cycles are required to perform the conversion read from the AD7298-1 always contains four channel address process and to access data from the AD7298-1. bits that the conversion result corresponds to, followed by the For the AD7298-1, four channel address bits (ADD3 to ADD0) 12-bit conversion result. that identify which channel the conversion result corresponds to, precede the 10 bits of data (see Table 8). t QUIET CS t ACQUISITION t 2 t 6 B 1 2 3 4 5 13 14 15 16 SCLK t 5 t t t t 3 4 7 8 THREE- STATE DON’T DON’T DOUT ADD3 ADD2 ADD1 ADD0 DB9 DB8 DB0 CARE CARE THREE- STATE t t 9 10 DIN WRITE REPEAT CH0 CH1 CH2 CH3 EXT_REF DONTC PPD Figure 28. Serial Interface Timing Diagram Rev. A | Page 20 of 24 09321-014 AD7298-1 LAYOUT AND CONFIGURATION For optimum performance, carefully consider the power supply The power supply line should have as large a trace as possible to and ground return layout on any PCB where the AD7298-1 is provide a low impedance path and reduce glitch effects on the used. The PCB containing the AD7298-1 should have separate supply line. Shield clocks and other components with fast switching analog and digital sections, each having its own area of the board. digital signals from other parts of the board by a digital ground. The AD7298-1 should be located in the analog section on any PCB. Avoid crossover of digital and analog signals, if possible. When traces cross on opposite sides of the board, ensure that they run Decouple the power supply to the AD7298-1 to ground with at right angles to each other to reduce feedthrough effects on 10 µF and 0.1 µF capacitors. Place the capacitors as physically the board. close as possible to the device, with the 0.1 µF capacitor ideally right up against the device. It is important that the 0.1 µF The best board layout technique is the microstrip technique where capacitor has low effective series resistance (ESR) and low the component side of the board is dedicated to the ground effective series inductance (ESL); common ceramic types of plane only, and the signal traces are placed on the solder side; capacitors are suitable. The 0.1 µF capacitors provide a low however, this is not always possible with a 2-layer board. impedance path to ground for high frequencies caused by transient currents due to internal logic switching. The 10 µF capacitors are the tantalum bead type. Rev. A | Page 21 of 24 AD7298-1 OUTLINE DIMENSIONS 4.10 0.30 4.00 SQ 0.25 3.90 0.18 PIN 1 INDICATOR 16 20 0.50 15 1 BSC EXPOSED 2.75 PAD 2.60 SQ 2.35 11 5 10 6 0.50 0.25 MIN TOP VIEW BOTTOM VIEW 0.40 0.30 0.80 FOR PROPER CONNECTION OF THE EXPOSED PAD, REFER TO 0.75 0.05 MAX THE PIN CONFIGURATION AND 0.70 FUNCTION DESCRIPTIONS 0.02 NOM SECTION OF THIS DATA SHEET. COPLANARITY SEATING 0.08 PLANE 0.20 REF COMPLIANT TO JEDEC STANDARDS MO-220-WGGD. Figure 29. 20-Lead Lead Frame Chip Scale Package [LFCSP_WQ] 4 mm × 4 mm Body, Very, Very Thin Quad (CP-20-8) Dimensions shown in millimeters ORDERING GUIDE 1 Model Temperature Range Package Description Package Option AD7298-1BCPZ −40°C to +125°C 20-Lead Lead Frame Chip Scale Package [LFCSP_WQ] CP-20-8 AD7298-1BCPZ-RL −40°C to +125°C 20-Lead Lead Frame Chip Scale Package [LFCSP_WQ] CP-20-8 1 Z = RoHS Compliant Part. Rev. A | Page 22 of 24 PIN 1 INDICATOR 020509-B AD7298-1 NOTES Rev. A | Page 23 of 24 AD7298-1 NOTES ©2010–2011 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D09321-0-1/11(A) Rev. A | Page 24 of 24
Frequently asked questions
What makes Elite.Parts unique?
What kind of warranty will the AD7298-1 have?
Which carriers does Elite.Parts work with?
Will Elite.Parts sell to me even though I live outside the USA?
I have a preferred payment method. Will Elite.Parts accept it?
Why buy from GID?
Quality
We are industry veterans who take pride in our work
Protection
Avoid the dangers of risky trading in the gray market
Access
Our network of suppliers is ready and at your disposal
Savings
Maintain legacy systems to prevent costly downtime
Speed
Time is of the essence, and we are respectful of yours
Manufacturers


What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods