ANALOG DEVICES AD5757
Description
Analog Devices AD5757 Quad Channel, 16-Bit, Serial Input, 4-20 MA Output DAC Dynamic Power Control, Hart Connectivity
Part Number
AD5757
Price
Request Quote
Manufacturer
ANALOG DEVICES
Lead Time
Request Quote
Category
PRODUCTS - A
Specifications
DAC Input Format
SPI
DAC Settling Time
15µs
DAC Type
Current Out
DAC Update Rate
60kSPS
Max Pos Supply (V)
+33V
Resolution (Bits)
16bit
Single-Supply
No
Features
- -40°C to +105°C temperature range
- 16-bit resolution and monotonicity
- Current output ranges: 0 mA to 20 mA, 4 mA to 20 mA, or 0 mA to 24 mA; ±0.05% total unadjusted error (TUE) maximum
- Dynamic power control for thermal management or external PMOS mode
- On-chip diagnostics
- On-chip reference (±10 ppm/°C maximum)
- User programmable offset and gain
Datasheet
Extracted Text
Quad Channel, 16-Bit, Serial Input, 4 mA to 20 mA Output DAC, Dynamic Power Control, HART Connectivity Data Sheet AD5757 a dc-to-dc boost converter optimized for minimum on-chip FEATURES power dissipation. 16-bit resolution and monotonicity Dynamic power control for thermal management Each channel has a corresponding CHART pin so that HART or external PMOS mode signals can be coupled onto the current output of the AD5757. Current output ranges: 0 mA to 20 mA, 4 mA to 20 mA, The part uses a versatile 3-wire serial interface that operates at or 0 mA to 24 mA clock rates of up to 30 MHz and is compatible with standard ±0.05% total unadjusted error (TUE) maximum SPI, QSPI™, MICROWIRE™, DSP, and microcontroller interface User programmable offset and gain standards. The interface also features optional CRC-8 packet On-chip diagnostics error checking, as well as a watchdog timer that monitors On-chip reference (±10 ppm/°C maximum) activity on the interface. −40°C to +105°C temperature range PRODUCT HIGHLIGHTS APPLICATIONS 1. Dynamic power control for thermal management. Process control 2. 16-bit performance. Actuator control 3. Multichannel. PLCs 4. HART compliant. HART network connectivity COMPANION PRODUCTS GENERAL DESCRIPTION Product Family: AD5755-1, AD5755 The AD5757 is a quad, current output DAC that operates with a HART Modem: AD5700, AD5700-1 power supply range from 10.8 V to 33 V. On-chip dynamic External References: ADR445, ADR02 power control minimizes package power dissipation by regulat- Digital Isolators: ADuM1410, ADuM1411 ing the voltage on the output driver from 7.4 V to 29.5 V using Power: ADP2302, ADP2303 Additional companion products on the AD5757 product page FUNCTIONAL BLOCK DIAGRAM AV CC 5.0V AV DD AGND +15V SW V x BOOST_x DV 7.4V TO 29.5V DD DGND DC-TO-DC LDAC CONVERTER SCLK SDIN SYNC DIGITAL I OUT_x INTERFACE SDO R + DAC A SET_x CLEAR CURRENT AND CHARTx VOLTAGE FAULT OUTPUT RANGE SCALING ALERT GAIN REG A AD1 OFFSET REG A AD0 DAC CHANNEL A REFOUT REFERENCE REFIN DAC CHANNEL B DAC CHANNEL C AD5757 DAC CHANNEL D NOTES 1. x = A, B, C, AND D. Figure 1. Rev. C Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. rights of third parties that may result from its use. Specifications subject to change without notice. No Tel: 781.329.4700 www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. Fax: 781.461.3113 ©2011–2012 Analog Devices, Inc. All rights reserved. 09225-101 AD5757 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 Readback Operation .................................................................. 32 Applications ....................................................................................... 1 Device Features ............................................................................... 34 General Description ......................................................................... 1 Output Fault ................................................................................ 34 Product Highlights ........................................................................... 1 Digital Offset and Gain Control ............................................... 34 Companion Products ....................................................................... 1 Status Readback During a Write .............................................. 34 Functional Block Diagram .............................................................. 1 Asynchronous Clear ................................................................... 34 Revision History ............................................................................... 3 Packet Error Checking ............................................................... 34 Detailed Functional Block Diagram .............................................. 4 Watchdog Timer ......................................................................... 35 Specifications ..................................................................................... 5 Output Alert ................................................................................ 35 AC Performance Characteristics ................................................ 7 Internal Reference ...................................................................... 35 Timing Characteristics ................................................................ 7 External Current Setting Resistor ............................................ 35 Absolute Maximum Ratings .......................................................... 10 HART ........................................................................................... 35 ESD Caution ................................................................................ 10 Digital Slew Rate Control .......................................................... 36 Pin Configuration and Function Descriptions ........................... 11 Power Dissipation Control ........................................................ 36 Typical Performance Characteristics ........................................... 14 DC-to-DC Converters ............................................................... 36 Current Outputs ......................................................................... 14 AICC Supply Requirements—Static .......................................... 38 DC-to-DC Block ......................................................................... 19 AICC Supply Requirements—Slewing ...................................... 38 Reference ..................................................................................... 20 External PMOS Mode ................................................................ 39 General ......................................................................................... 21 Applications Information .............................................................. 40 Terminology .................................................................................... 22 Current Output Mode with Internal R ................................ 40 SET Theory of Operation ...................................................................... 23 Precision Voltage Reference Selection ..................................... 40 DAC Architecture ....................................................................... 23 Driving Inductive Loads ............................................................ 40 Power-On State of the AD5757 ................................................ 23 Transient Voltage Protection .................................................... 41 Serial Interface ............................................................................ 23 Microprocessor Interfacing ....................................................... 41 Transfer Function ....................................................................... 24 Layout Guidelines....................................................................... 41 Registers ........................................................................................... 25 Galvanically Isolated Interface ................................................. 42 Programming Sequence to Write/Enable the Output Industrial HART Capable Analog Output Correctly ...................................................................................... 26 Application .................................................................................. 43 Changing and Reprogramming the Range ............................. 26 Outline Dimensions ....................................................................... 44 Data Registers ............................................................................. 27 Ordering Guide .......................................................................... 44 Control Registers ........................................................................ 29 Rev. C | Page 2 of 44 Data Sheet AD5757 REVISION HISTORY Change to Figure 54 ........................................................................ 35 5/12—Rev. B to Rev. C Change to Figure 58 Caption ......................................................... 38 Changes to Companion Products Section ..................................... 1 Changes to Figure 59, Figure 60, and Figure 61 Captions ......... 39 Changes to Table 5 .......................................................................... 13 Changes to Transient Voltage Protection Section and Added Industrial HART Capable Analog Output Application Figure 63 ........................................................................................... 41 Section and Figure 66, Renumbered Sequentially ...................... 43 Changes to Galvanically Isolated Interface Section .................... 42 Updated Outline Dimensions ........................................................ 44 5/11—Rev. 0 to Rev. A 11/11—Rev. A to Rev. B Changes Features Section ................................................................. 1 Change to Test Conditions/Comments of Accuracy (External Changes to Figure 2 .......................................................................... 3 RSET) Parameter, Table 1 .................................................................... 5 Changed AV Min Parameter from 10.8 V to 9 V ...................... 5 Changes to Figure 4........................................................................... 8 DD Changes to Pin 22, Pin31, Pin 49 Descriptions ........................... 11 Changes to Figure 5........................................................................... 9 Changes to Pin 58 Descriptions .................................................... 12 Change to Pin 8 Description, Table 5 ........................................... 11 Changes to Figure 8, Figure 9, and Figure 10 .............................. 13 Change to Figure 13 ........................................................................ 14 Added Figure 23, Renumbered Sequentially ............................... 15 Change to Figure 20 ........................................................................ 16 Added Figure 29 .............................................................................. 16 Changes to Figure 48 and Power-On State of the AD5757 Added External PMOS Mode Section and Figure 62................. 38 Section .............................................................................................. 23 Change to Table 16 .......................................................................... 29 Changes to Readback Operation Section, Readback Example 4/11—Revision 0: Initial Version Section, and Table 25 ...................................................................... 32 Rev. C | Page 3 of 44 AD5757 Data Sheet DETAILED FUNCTIONAL BLOCK DIAGRAM AV CC 5.0V AV DD AGND +15V SW V A BOOST_A DV POWER-ON DD DC-TO-DC RESET CONVERTER DGND V V SEN1 SEN2 POWER 7.4V TO 29.5V LDAC CONTROL REG CLEAR INPUT SHIFT SCLK REGISTER 16 16 R2 R3 INPUT DAC AND SDIN + DAC A REG A REG A CONTROL SYNC SDO GAIN REG A FAULT I OUT_A OFFSET REG A STATUS REGISTER R R1 SET_A WATCHDOG ALERT TIMER (SPI ACTIVITY) CHARTA REFOUT VREF DAC CHANNEL A REFERENCE REFIN BUFFERS I , I , I OUT_B OUT_C OUT_D R , R , R DAC CHANNEL B SET_B SET_C SET_D AD1 CHARTB, CHARTC, CHARTD DAC CHANNEL C AD5757 DAC CHANNEL D AD0 V , V , V SW , SW , SW BOOST_B BOOST_C BOOST_D B C D Figure 2. Rev. C | Page 4 of 44 09225-001 Data Sheet AD5757 SPECIFICATIONS AVDD = VBOOST_x = 15 V; DVDD = 2.7 V to 5.5 V; AVCC = 4.5 V to 5.5 V; dc-to-dc converter disabled; AGND = DGND = GNDSWx = 0 V; REFIN = 5 V; RL = 300 Ω; all specifications TMIN to TMAX, unless otherwise noted. Table 1. 1 Parameter Min Typ Max Unit Test Conditions/Comments CURRENT OUTPUT Output Current Ranges 0 24 mA 0 20 mA 4 20 mA Resolution 16 Bits ACCURACY (EXTERNAL R ) Assumes ideal resistor; see the External Current SET Setting Resistor section for more information Total Unadjusted Error (TUE) −0.05 ±0.009 +0.05 % FSR TUE Long-Term Stability 100 ppm FSR Drift after 1000 hours, T = 150°C J Relative Accuracy (INL) −0.006 +0.006 % FSR Differential Nonlinearity (DNL) −1 +1 LSB Guaranteed monotonic Offset Error −0.05 ±0.005 +0.05 % FSR 2 Offset Error Drift ±4 ppm FSR/°C Gain Error −0.05 ±0.004 +0.05 % FSR 2 Gain TC ±3 ppm FSR/°C Full-Scale Error −0.05 ±0.008 +0.05 % FSR 2 Full-Scale TC ±5 ppm FSR/°C DC Crosstalk 0.0005 % FSR External RSET ACCURACY (INTERNAL R ) SET 3, 4 Total Unadjusted Error (TUE) −0.14 +0.14 % FSR −0.11 ±0.009 +0.11 % FSR T = 25°C A TUE Long-Term Stability 180 ppm FSR Drift after 1000 hours, TJ = 150°C Relative Accuracy (INL) −0.006 +0.006 % FSR −0.004 +0.004 % FSR TA = 25°C Differential Nonlinearity (DNL) −1 +1 LSB Guaranteed monotonic 3, 4 Offset Error −0.05 +0.05 % FSR −0.04 ±0.007 +0.04 % FSR TA = 25°C 2 Offset Error Drift ±6 ppm FSR/°C Gain Error −0.12 +0.12 % FSR −0.06 ±0.002 +0.06 % FSR TA = 25°C 2 Gain TC ±9 ppm FSR/°C 3, 4 Full-Scale Error −0.14 +0.14 % FSR −0.1 ±0.007 +0.1 % FSR T = 25°C A 2 Full-Scale TC ±14 ppm FSR/°C 4 DC Crosstalk −0.011 % FSR Internal R SET 2 OUTPUT CHARACTERISTICS Current Loop Compliance Voltage VBOOST_x − VBOOST_x − V 2.4 2.7 Output Current Drift vs. Time Drift after 1000 hours, ¾ scale output, TJ = 150°C 90 ppm FSR External RSET 140 ppm FSR Internal RSET Resistive Load 1000 Ω The dc-to-dc converter has been characterized with a maximum load of 1 kΩ, chosen such that compliance is not exceeded; see Figure 31 and DC-DC MaxV bits in Table 24 Output Impedance 100 MΩ DC PSRR 0.02 1 µA/V REFERENCE INPUT/OUTPUT 2 Reference Input Reference Input Voltage 4.95 5 5.05 V For specified performance DC Input Impedance 45 150 MΩ Rev. C | Page 5 of 44 AD5757 Data Sheet 1 Parameter Min Typ Max Unit Test Conditions/Comments Reference Output Output Voltage 4.995 5 5.005 V TA = 25°C 2 Reference TC −10 ±5 +10 ppm/°C 2 Output Noise (0.1 Hz to 10 Hz) 7 µV p-p 2 Noise Spectral Density 100 nV/√Hz At 10 kHz 2 Output Voltage Drift vs. Time 180 ppm Drift after 1000 hours, TJ = 150°C 2 Capacitive Load 1000 nF Load Current 9 mA See Figure 42 Short-Circuit Current 10 mA 2 Line Regulation 3 ppm/V See Figure 43 2 Load Regulation 95 ppm/mA See Figure 42 2 Thermal Hysteresis 160 ppm First temperature cycle 5 ppm Second temperature cycle DC-TO-DC Switch Switch On Resistance 0.425 Ω Switch Leakage Current 10 nA Peak Current Limit 0.8 A Oscillator Oscillator Frequency 11.5 13 14.5 MHz This oscillator is divided down to give the dc-to-dc converter switching frequency Maximum Duty Cycle 89.6 % At 410 kHz dc-to-dc switching frequency 2 DIGITAL INPUTS JEDEC compliant VIH, Input High Voltage 2 V VIL, Input Low Voltage 0.8 V Input Current −1 +1 µA Per pin Pin Capacitance 2.6 pF Per pin 2 DIGITAL OUTPUTS SDO, ALERT VOL, Output Low Voltage 0.4 V Sinking 200 µA VOH, Output High Voltage DVDD − 0.5 V Sourcing 200 µA High Impedance Leakage Current −1 +1 µA High Impedance Output 2.5 pF Capacitance FAULT VOL, Output Low Voltage 0.4 V 10 kΩ pull-up resistor to DVDD VOL, Output Low Voltage 0.6 V At 2.5 mA VOH, Output High Voltage 3.6 V 10 kΩ pull-up resistor to DVDD POWER REQUIREMENTS AVDD 9 33 V DVDD 2.7 5.5 V AVCC 4.5 5.5 V AIDD 7 7.5 mA DICC 9.2 11 mA VIH = DVDD, VIL = DGND, internal oscillator running, over supplies AICC 1 mA Over supplies 5 IBOOST 1 mA Per channel, current output mode, 0 mA output Power Dissipation 155 mW AVDD = 15 V, DVCC = 5 V, dc-to-dc converter enable, current output mode, outputs disabled 1 Temperature range: −40°C to +105°C; typical at +25°C. 2 Guaranteed by design and characterization; not production tested. 3 For current outputs with internal R , the offset, full-scale, and TUE measurements exclude dc crosstalk. The measurements are made with all four channels enabled SET loaded with the same code. 4 See the Current Output Mode with Internal R section for more explanation of the dc crosstalk. SET 5 Efficiency plots in Figure 33, Figure 34, Figure 35, and Figure 36 include the IBOOST quiescent current. Rev. C | Page 6 of 44 Data Sheet AD5757 AC PERFORMANCE CHARACTERISTICS AVDD = VBOOST_x = 15 V; DVDD = 2.7 V to 5.5 V; AVCC = 4.5 V to 5.5 V; dc-to-dc converter disabled; AGND = DGND = GNDSWx = 0 V; REFIN = 5 V; RL = 300 Ω; all specifications TMIN to TMAX, unless otherwise noted. Table 2. 1 Parameter Min Typ Max Unit Test Conditions/Comments DYNAMIC PERFORMANCE Current Output Output Current Settling Time 15 µs To 0.1% FSR (0 mA to 24 mA) See test conditions/ ms See Figure 26, Figure 27, and Figure 28 comments Output Noise (0.1 Hz to 10 Hz 0.15 LSB p-p 16-bit LSB, 0 mA to 24 mA range Bandwidth) Output Noise Spectral Density 0.5 nA/√Hz Measured at 10 kHz, midscale output, 0 mA to 24 mA range 1 Guaranteed by design and characterization; not production tested. TIMING CHARACTERISTICS AV = V = 15 V; DV = 2.7 V to 5.5 V; AV = 4.5 V to 5.5 V; dc-to-dc converter disabled; AGND = DGND = GNDSW = 0 V; DD BOOST_x DD CC x REFIN = 5 V; R = 300 Ω; all specifications T to T , unless otherwise noted. L MIN MAX Table 3. 1, 2, 3 Parameter Limit at T , T Unit Description MIN MAX t 33 ns min SCLK cycle time 1 t 13 ns min SCLK high time 2 t3 13 ns min SCLK low time t4 13 ns min SYNC falling edge to SCLK falling edge setup time th nd t5 13 ns min 24 /32 SCLK falling edge to SYNC rising edge (see Figure 54) t 198 ns min SYNC high time 6 t 5 ns min Data setup time 7 t 5 ns min Data hold time 8 t9 20 µs min SYNC rising edge to LDAC falling edge (all DACs updated or any channel has digital slew rate control enabled) 5 µs min SYNC rising edge to LDAC falling edge (single DAC updated) t 10 ns min LDAC pulse width low 10 t 500 ns max LDAC falling edge to DAC output response time 11 t See the AC Performance µs max DAC output settling time 12 Characteristics section t13 10 ns min CLEAR high time t 5 µs max CLEAR activation time 14 t 40 ns max SCLK rising edge to SDO valid 15 t 21 µs min rising edge to DAC output response time ( = 0) (all DACs updated) 16 SYNC LDAC 5 µs min SYNC rising edge to DAC output response time (LDAC = 0) (single DAC updated) t17 500 ns min LDAC falling edge to SYNC rising edge t18 800 ns min RESET pulse width 4 t 20 µs min SYNC high to next SYNC low (digital slew rate control enabled) (all DACs updated) 19 5 µs min SYNC high to next SYNC low (digital slew rate control disabled) (single DAC updated) 1 Guaranteed by design and characterization; not production tested. 2 All input signals are specified with tRISE = tFALL = 5 ns (10% to 90% of DVDD) and timed from a voltage level of 1.2 V. 3 See Figure 3, Figure 4, Figure 5, and Figure 6. 4 This specification applies if LDAC is held low during the write cycle; otherwise, see t . 9 Rev. C | Page 7 of 44 AD5757 Data Sheet Timing Diagrams t 1 SCLK 1 2 24 t t t 3 2 6 t t 4 5 SYNC t 8 t 19 t 7 SDIN MSB LSB t t 10 10 t 9 LDAC t t 17 12 t 11 I OUT_x LDAC = 0 t 12 t 16 I OUT_x t 13 CLEAR t 14 I OUT_x t 18 RESET Figure 3. Serial Interface Timing Diagram SCLK 1 1 24 24 t 6 SYNC MSB LSB MSB LSB SDIN INPUT WORD SPECIFIES NOP CONDITION REGISTER TO BE READ MSB LSB SDO UNDEFINED SELECTED REGISTER DATA CLOCKED OUT t 15 Figure 4. Readback Timing Diagram Rev. C | Page 8 of 44 09225-002 09225-003 Data Sheet AD5757 LSB MSB 1 2 16 SCLK SYNC DUT_ DUT_ R/W X X X D15 D14 D1 D0 SDIN AD1 AD0 SDO_ SDO SDO DISABLED STATUS STATUS STATUS STATUS ENAB Figure 5. Status Readback During Write 200µA I OL V (MIN) OR TO OUTPUT OH PIN V (MAX) OL C L 50pF 200µA I OH Figure 6. Load Circuit for SDO Timing Diagram Rev. C | Page 9 of 44 09225-005 09225-004 AD5757 Data Sheet ABSOLUTE MAXIMUM RATINGS TA = 25°C, unless otherwise noted. Transient currents of up to Stresses above those listed under Absolute Maximum Ratings 100 mA do not cause SCR latch-up. may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any Table 4. other conditions above those indicated in the operational Parameter Rating section of this specification is not implied. Exposure to absolute AV , V to AGND, DGND −0.3 V to +33 V DD BOOST_x maximum rating conditions for extended periods may affect AVCC to AGND −0.3 V to +7 V device reliability. DVDD to DGND −0.3 V to +7 V Digital Inputs to DGND −0.3 V to DVDD + 0.3 V or +7 V ESD CAUTION (whichever is less) Digital Outputs to DGND −0.3 V to DV + 0.3 V or +7 V DD (whichever is less) REFIN, REFOUT to AGND −0.3 V to AVDD + 0.3 V or +7 V (whichever is less) IOUT_x to AGND AGND to VBOOST_x or 33 V if using the dc-to-dc circuitry SW to AGND −0.3 V to +33 V x AGND, GNDSWx to DGND −0.3 V to +0.3 V Operating Temperature Range (TA) 1 Industrial −40°C to +105°C Storage Temperature Range −65°C to +150°C Junction Temperature (T max) 125°C J 64-Lead LFCSP 2 θJA Thermal Impedance 20°C/W Power Dissipation (TJ max – TA)/θJA Lead Temperature JEDEC industry standard Soldering J-STD-020 1 Power dissipated on chip must be derated to keep the junction temperature below 125°C. 2 Based on a JEDEC 4-layer test board. Rev. C | Page 10 of 44 Data Sheet AD5757 PIN CONFIGURATION AND FUNCTION DESCRIPTIONS PIN 1 INDICATOR R 1 48 COMP SET_B DCDC_C R 2 47 I SET_A OUT_C REFGND 3 46 V BOOST_C REFGND 4 45 AV CC AD0 5 44 SW C AD1 6 43 GNDSW C SYNC 7 42 GNDSW AD5757 D SCLK 8 41 SW D TOP VIEW SDIN 9 40 AGND (Not to Scale) SDO 10 39 SW A DV 11 38 DD GNDSW A DGND 12 37 GNDSW B LDAC 13 36 SW B CLEAR 14 35 AGND ALERT 15 34 V BOOST_B FAULT 16 33 I OUT_B NOTES 1. NC = NO CONNECT. DO NOT CONNECT TO THIS PIN. 2. THE EXPOSED PAD SHOULD BE CONNECTED TO AGND, OR ALTERNATIVELY, IT CAN BE LEFT ELECTRICALLY UNCONNECTED. IT IS RECOMMENDED THAT THE PAD BE THERMALLY CONNECTED TO A COPPER PLANE FOR ENHANCED THERMAL PERFORMANCE. Figure 7. Pin Configuration Table 5. Pin Function Descriptions Pin No. Mnemonic Description 1 RSET_B An external, precision, low drift 15 kΩ current setting resistor can be connected to this pin to improve the IOUT_B temperature drift performance. See the Device Features section. 2 RSET_A An external, precision, low drift 15 kΩ current setting resistor can be connected to this pin to improve the IOUT_A temperature drift performance. See the Device Features section. 3, 4 REFGND Ground Reference Point for Internal Reference. 5 AD0 Address Decode for the Device Under Test (DUT) on the Board. 6 AD1 Address Decode for the DUT on the Board. 7 SYNC Active Low Input. This is the frame synchronization signal for the serial interface. While SYNC is low, data is transferred in on the falling edge of SCLK. 8 SCLK Serial Clock Input. Data is clocked into the input shift register on the falling edge of SCLK. This pin operates at clock speeds of up to 30 MHz. 9 SDIN Serial Data Input. Data must be valid on the falling edge of SCLK. 10 SDO Serial Data Output. Used to clock data from the serial register in readback mode. See Figure 4 and Figure 5. 11 DVDD Digital Supply. The voltage range is from 2.7 V to 5.5 V. 12, 17 DGND Digital Ground. 13 LDAC Load DAC, Active Low Input. This is used to update the DAC register and consequently the DAC outputs. When tied permanently low, the addressed DAC data register is updated on the rising edge of . If is held SYNC LDAC high during the write cycle, the DAC input register is updated, but the DAC output update only takes place at the falling edge of LDAC (see Figure 3). Using this mode, all analog outputs can be updated simultaneously. The LDAC pin must not be left unconnected. 14 CLEAR Active High, Edge Sensitive Input. Asserting this pin sets the output current and voltage to the preprogrammed clear code bit setting. Only channels enabled to be cleared are cleared. See the Device Features section for more information. When CLEAR is active, the DAC output register cannot be written to. Rev. C | Page 11 of 44 DGND 17 64 R SET_C RESET 18 63 R SET_D AV 19 62 DD REFOUT NC 20 61 REFIN 21 60 NC CHARTA IGATEA 22 59 CHARTD COMP 23 58 IGATED DCDC_A V 24 57 COMP BOOST_A DCDC_D NC 25 56 V BOOST_D I 26 55 NC OUT_A 27 54 I AGND OUT_D NC 28 53 AGND CHARTB 29 52 NC NC 30 51 CHARTC IGATEB 31 50 NC COMP 32 49 IGATEC DCDC_B 09225-006 AD5757 Data Sheet Pin No. Mnemonic Description 15 ALERT Active High Output. This pin is asserted when there has been no SPI activity on the interface pins for a predetermined time. See the Device Features section for more information. 16 FAULT Active Low Output. This pin is asserted low when an open circuit in current mode is detected, a short circuit in voltage mode is detected, a PEC error is detected, or an overtemperature is detected (see the Device Features section). Open-drain output. 18 Hardware Reset. Active Low Input. RESET 19 AVDD Positive Analog Supply. The voltage range is from 10.8 V to 33 V. 20, 25, NC No Connect. Do not connect to this pin. 28, 30, 50, 52, 55, 60 21 CHARTA HART Input Connection for DAC Channel A. 22 IGATEA Optional Connection for External Pass Transistor. Should be left unconnected when using the dc-to-dc converter. See the External PMOS Mode section for more information. 23 COMP DC-to-DC Compensation Capacitor. Connect a 10 nF capacitor from this pin to ground. Used to regulate the DCDC_A feedback loop of the Channel A dc-to-dc converter. Alternatively, if using an external compensation resistor, place a resistor in series with a capacitor to ground from this pin (see the DC-to-DC Converter Compensation Capacitors and the AICC Supply Requirements—Slewing sections in the Device Features section for more information). 24 VBOOST_A Supply for Channel A Current Output Stage (see Figure 49). To use the dc-to-dc feature of the device, connect as shown in Figure 56. 26 I Current Output Pin for DAC Channel A. OUT_A 27, 40, 53 AGND Ground Reference Point for Analog Circuitry. This must be connected to 0 V. 29 CHARTB HART Input Connection for DAC Channel B. 31 IGATEB Optional Connection for External Pass Transistor. Should be left unconnected when using the dc-to-dc converter. See the External PMOS Mode section for more information. 32 COMP DC-to-DC Compensation Capacitor. Connect a 10 nF capacitor from this pin to ground. Used to regulate the DCDC_B feedback loop of the Channel B dc-to-dc converter. Alternatively, if using an external compensation resistor, place a resistor in series with a capacitor to ground from this pin (see the DC-to-DC Converter Compensation Capacitors and AICC Supply Requirements—Slewing sections in the Device Features section for more information). 33 I Current Output Pin for DAC Channel B. OUT_B 34 V Supply for Channel B Current Output Stage (see Figure 49). To use the dc-to-dc feature of the device, connect as BOOST_B shown in Figure 56. 35 AGND Ground Reference Point for Analog Circuitry. This pin must be connected to 0 V. 36 SWB Switching Output for Channel B DC-to-DC Circuitry. To use the dc-to-dc feature of the device, connect as shown in Figure 56. 37 GNDSW Ground Connection for DC-to-DC Switching Circuit. This pin should always be connected to ground. B 38 GNDSW Ground Connection for DC-to-DC Switching Circuit. This pin should always be connected to ground. A 39 SWA Switching Output for Channel A DC-to-DC Circuitry. To use the dc-to-dc feature of the device, connect as shown in Figure 56. 41 SWD Switching Output for Channel D DC-to-DC Circuitry. To use the dc-to-dc feature of the device, connect as shown in Figure 56. 42 GNDSW Ground Connections for DC-to-DC Switching Circuit. This pin should always be connected to ground. D 43 GNDSWC Ground Connections for DC-to-DC Switching Circuit. This pin should always be connected to ground. 44 SWC Switching Output for Channel C DC-to-DC Circuitry. To use the dc-to-dc feature of the device, connect as shown in Figure 56. 45 AV Supply for DC-to-DC Circuitry. CC 46 V Supply for Channel C Current Output Stage (see Figure 49). To use the dc-to-dc feature of the device, connect as BOOST_C shown in Figure 56. 47 IOUT_C Current Output Pin for DAC Channel C. 48 COMPDCDC_C DC-to-DC Compensation Capacitor. Connect a 10 nF capacitor from this pin to ground. Used to regulate the feedback loop of the Channel C dc-to-dc converter. Alternatively, if using an external compensation resistor, place a resistor in series with a capacitor to ground from this pin (see the DC-to-DC Converter Compensation Capacitors and AI Supply Requirements—Slewing sections in the Device Features section for more CC information). 49 IGATEC Optional Connection for External Pass Transistor. Should be left unconnected when using the dc-to-dc converter. See the External PMOS Mode section for more information. Rev. C | Page 12 of 44 Data Sheet AD5757 Pin No. Mnemonic Description 51 CHARTC HART Input Connection for DAC Channel C. 54 IOUT_D Current Output Pin for DAC Channel D. 56 VBOOST_D Supply for Channel D Current Output Stage (see Figure 49). To use the dc-to-dc feature of the device, connect as shown in Figure 56. 57 COMP DC-to-DC Compensation Capacitor. Connect a 10 nF capacitor from this pin to ground. Used to regulate the DCDC_D feedback loop of the Channel D dc-to-dc converter. Alternatively, if using an external compensation resistor, place a resistor in series with a capacitor to ground from this pin (see the DC-to-DC Converter Compensation Capacitors and AICC Supply Requirements—Slewing sections in the Device Features section for more information). 58 IGATED Optional Connection for External Pass Transistor. Should be left unconnected when using the dc-to-dc converter. See the External PMOS Mode section for more information. 59 CHARTD HART Input Connection for DAC Channel D. 61 REFIN External Reference Voltage Input. 62 REFOUT Internal Reference Voltage Output. It is recommended to place a 0.1 µF capacitor between REFOUT and REFGND. REFOUT must be connected to REFIN to use the internal reference. 63 RSET_D An external, precision, low drift 15 kΩ current setting resistor can be connected to this pin to improve the IOUT_D temperature drift performance. See the Device Features section. 64 RSET_C An external, precision, low drift 15 kΩ current setting resistor can be connected to this pin to improve the IOUT_C temperature drift performance. See the Device Features section. EPAD Exposed Pad. This exposed pad should be connected to AGND, or, alternatively, it can be left electrically unconnected. It is recommended that the pad be thermally connected to a copper plane for enhanced thermal performance. Rev. C | Page 13 of 44 AD5757 Data Sheet TYPICAL PERFORMANCE CHARACTERISTICS CURRENT OUTPUTS 0.0025 0.0010 AV = 15V DD 0.0020 T = 25°C 0.0008 A 0.0015 0.0006 0.0010 0.0004 4mA TO 20mA RANGE MAX INL AV = 15V DD 0.0005 0.0002 0mA TO 24mA RANGE MAX INL 0mA TO 20mA RANGE MIN INL 0 0 0mA TO 20mA RANGE MAX INL 4mA TO 20mA RANGE MAX INL –0.0005 –0.0002 0mA TO 24mA RANGE MIN INL –0.0010 –0.0004 4mA TO 20mA, EXTERNAL R –0.0006 –0.0015 SET 4mA TO 20mA, EXTERNAL R , WITH DC-TO-DC CONVERTER SET 4mA TO 20mA, INTERNAL R SET –0.0020 –0.0008 4mA TO 20mA, INTERNAL R , WITH DC-TO-DC CONVERTER SET 4mA TO 20mA, EXTERNAL R , EXTERNAL PMOS MODE SET –0.0025 –0.0010 0 10000 20000 30000 40000 50000 60000 –40 –20 0 20 40 60 80 100 CODE TEMPERATURE (°C) Figure 8. Integral Nonlinearity vs. Code Figure 11. Integral Nonlinearity vs. Temperature, Internal RSET 0.0020 1.0 4mA TO 20mA, EXTERNAL R SET 4mA TO 20mA RANGE MAX INL 4mA TO 20mA, EXTERNAL R , WITH DC-TO-DC CONVERTER SET 0.8 0.0015 0mA TO 24mA RANGE MAX INL 4mA TO 20mA, INTERNAL R SET 0mA TO 20mA RANGE MIN INL 4mA TO 20mA, INTERNAL R , WITH DC-TO-DC CONVERTER SET 0.6 4mA TO 20mA, EXTERNAL R , EXTERNAL PMOS MODE SET 0.0010 0.4 0.0005 0.2 0mA TO 20mA RANGE MAX INL 4mA TO 20mA RANGE MIN INL 0 0 0mA TO 24mA RANGE MIN INL –0.2 –0.0005 –0.4 –0.0010 –0.6 AV = 15V DD –0.0015 AV = 15V DD –0.8 T = 25°C A –0.0020 –1.0 –40 –20 0 20 40 60 80 100 0 10000 20000 30000 40000 50000 60000 CODE TEMPERATURE (°C) Figure 12. Integral Nonlinearity vs. Temperature, External R Figure 9. Differential Nonlinearity vs. Code SET 1.0 0.035 AV = 15V AV = 15V DD DD ALL RANGES T = 25°C 0.030 A 0.8 INTERNAL AND EXTERNAL R ALL CHANNELS ENABLED SET 0.025 0.6 0.020 0.4 4mA TO 20mA, EXTERNAL R SET 4mA TO 20mA, EXTERNAL R , WITH DC-TO-DC CONVERTER SET 0.015 0.2 4mA TO 20mA, INTERNAL R SET 4mA TO 20mA, INTERNAL R , WITH DC-TO-DC CONVERTER SET DNL ERROR MAX 0.010 0 4mA TO 20mA, EXTERNAL R , EXTERNAL PMOS MODE SET DNL ERROR MIN 0.005 –0.2 0 –0.4 –0.005 –0.6 –0.010 –0.8 –0.015 –1.0 0 10000 20000 30000 40000 50000 60000 –40 –20 0 20 40 60 80 100 TEMPERATURE (°C) CODE Figure 13. Differential Nonlinearity vs. Temperature Figure 10. Total Unadjusted Error vs. Code Rev. C | Page 14 of 44 INL ERROR (%FSR) TOTAL UNADJUSTED ERROR (%FSR) DNL ERROR (LSB) 09225-150 09225-151 09225-149 INL ERROR (%FSR) INL ERROR (%FSR) DNL ERROR (LSB) 09225-154 09225-153 09225-152 Data Sheet AD5757 0.03 0.02 0.02 0.01 0.01 0 0 –0.01 –0.01 –0.02 –0.02 –0.03 AV = 15V DD AV = 15V DD 4mA TO 20mA INTERNAL R –0.03 –0.04 SET 4mA TO 20mA INTERNAL R 0mA TO 20mA INTERNAL R SET SET 0mA TO 20mA INTERNAL R –0.05 SET 0mA TO 24mA INTERNAL R SET –0.04 0mA TO 24mA INTERNAL R SET 4mA TO 20mA EXTERNAL R SET –0.06 4mA TO 20mA EXTERNAL R SET 0mA TO 20mA EXTERNAL R SET 0mA TO 20mA EXTERNAL R –0.05 SET 0mA TO 24mA EXTERNAL R SET –0.07 0mA TO 24mA EXTERNAL R SET –0.08 –0.06 –40 –20 0 20 40 60 80 100 –40 –20 0 20 40 60 80 100 TEMPERATURE (°C) TEMPERATURE (°C) Figure 14. Total Unadjusted Error vs. Temperature Figure 17. Gain Error vs. Temperature 0.03 0.0025 4mA TO 20mA RANGE MAX INL 0.02 0.0020 4mA TO 20mA RANGE MIN INL T = 25°C A 0.01 0.0015 0 0.0010 –0.01 0.0005 –0.02 –0.03 AV = 15V 0 DD –0.04 4mA TO 20mA INTERNAL R SET –0.0005 0mA TO 20mA INTERNAL R SET –0.05 0mA TO 24mA INTERNAL R SET –0.0010 4mA TO 20mA EXTERNAL R SET –0.06 0mA TO 20mA EXTERNAL R SET –0.0015 0mA TO 24mA EXTERNAL R –0.07 SET –0.08 –0.0020 10 15 20 25 30 –40 –20 0 20 40 60 80 100 TEMPERATURE (°C) SUPPLY (V) Figure 15. Full-Scale Error vs. Temperature Figure 18. Integral Nonlinearity Error vs. AVDD, Over Supply, External RSET 0.020 0.0015 0.015 0.0010 0.010 0.0005 0.005 0 0 –0.0005 AV = 15V DD –0.005 –0.0010 4mA TO 20mA INTERNAL R SET 0mA TO 20mA INTERNAL R SET 4mA TO 20mA RANGE MAX INL –0.010 –0.0015 0mA TO 24mA INTERNAL R SET 4mA TO 20mA RANGE MIN INL 4mA TO 20mA EXTERNAL R SET T = 25°C A 0mA TO 20mA EXTERNAL R –0.015 –0.0020 SET 0mA TO 24mA EXTERNAL R SET –0.020 –0.0025 10 15 20 25 30 –40 –20 0 20 40 60 80 100 TEMPERATURE (°C) SUPPLY (V) Figure 16. Offset Error vs. Temperature Figure 19. Integral Nonlinearity Error vs. AVDD, Over Supply, Internal RSET Rev. C | Page 15 of 44 OFFSET ERROR (%FSR) FULL-SCALE ERROR (%FSR) TOTAL UNADJSUTED ERROR (%FSR) 09225-157 09225-155 09225-158 INL ERROR (%FSR) INL ERROR (%FSR) GAIN ERROR (%FSR) 09225-159 09225-057 09225-056 AD5757 Data Sheet 1.0 0.006 ALL RANGES INTERNAL AND EXTERNAL R SET 0.8 MAX OF TUE 0.004 T = 25°C A 0.6 0.002 0.4 0 0.2 –0.002 DNL ERROR MAX 0 DNL ERROR MIN T = 25°C A –0.004 EXTERNAL PMOS (NTLJS4149) –0.2 4mA TO 20mA RANGE –0.006 R = 300Ω LOAD –0.4 –0.008 –0.6 MIN OF TUE –0.010 –0.8 –0.012 –1.0 10 15 20 25 30 10 15 20 25 30 SUPPLY (V) V SUPPLY (V) BOOST_X Figure 20. Differential Nonlinearity Error vs. AVDD Figure 23. Total Unadjusted Error vs. VBOOST_X, Using External PMOS Mode 0.012 6 AV = 15V DD T = 25°C A 0.010 5 R = 300Ω LOAD 0.008 4 0.006 3 0.004 2 4mA TO 20mA RANGE MAX TUE 4mA TO 20mA RANGE MIN TUE 0.002 1 T = 25°C A 0 0 10 15 20 25 30 0 5 10 15 20 SUPPLY (V) TIME (µs) Figure 21. Total Unadjusted Error vs. AV , External R DD SET Figure 24. Output Current vs. Time on Power-Up 0 4 –0.002 2 –0.004 0 –0.006 4mA TO 20mA RANGE MAX TUE –0.008 4mA TO 20mA RANGE MIN TUE –2 T = 25°C A –0.010 –4 –0.012 –0.014 –6 AV = 15V DD T = 25°C A –0.016 R = 300Ω LOAD –8 INT_ENABLE –0.018 –10 –0.020 0 1 2 3 4 5 6 10 15 20 25 30 SUPPLY (V) TIME (µs) Figure 22. Total Unadjusted Error vs. AV , Internal R DD SET Figure 25. Output Current vs. Time on Output Enable Rev. C | Page 16 of 44 TOTAL UNADJUSTED ERROR (%FSR) TOTAL UNADJUSTED ERROR (%FSR) DNL ERROR (LSB) 09225-162 09225-060 09225-061 CURRENT (µA) TOTAL UNADJUSTED ERROR (%FSR) VOLTAGE (µA) 09225-063 09225-062 09225-188 Data Sheet AD5757 30 30 25 25 20 20 I , AV = 4.5V 15 I 15 OUT OUT CC V I , AV = 5.0V BOOST OUT CC I , AV = 5.5V OUT CC 10 10 0mA TO 24mA RANGE 1kΩ LOAD 0mA TO 24mA RANGE f = 410kHz SW 1kΩ LOAD INDUCTOR = 10µH (XAL4040-103) 5 5 f = 410kHz SW AV = 5V CC INDUCTOR = 10µH (XAL4040-103) T = 25°C A T = 25°C A 0 0 –0.25 0 0.25 0.50 0.75 1.00 1.25 1.50 1.75 –0.50 –0.25 0 0.25 0.50 0.75 1.00 1.25 1.50 1.75 2.00 TIME (ms) TIME (ms) Figure 26. Output Current and V Settling Time with DC-to-DC Figure 28. Output Current Settling with DC-to-DC Converter vs. Time and BOOST_x Converter (See Figure 56) AVCC (See Figure 56) 25 30 I (4mA TO 20mA STEP) OUT 25 20 20 15 T = 25°C A EXTERNAL PMOS (NTLJS4149) I , T = –40°C 4mA TO 20mA RANGE 15 OUT A R = 300Ω I , T = +25°C OUT A LOAD I , T = +105°C V = 24V OUT A 10 BOOST_X 10 0mA TO 24mA RANGE I (20mA TO 4mA STEP) OUT 1kΩ LOAD 5 5 f = 410kHz SW INDUCTOR = 10µH (XAL4040-103) AV = 5V CC 0 0 –5 0 5 10 15 20 –0.25 0 0.25 0.50 0.75 1.00 1.25 1.50 1.75 TIME (ms) TIME (µs) Figure 27. Output Current Settling with DC-to-DC Converter vs. Time and Figure 29. Output Current Settling Time with External PMOS Transistor Temperature (See Figure 56) Rev. C | Page 17 of 44 OUTPUT CURRENT (mA) OUTPUT CURRENT (mA) 09225-168 09225-167 TOTAL UNADJUSTED ERROR (%FSR) OUTPUT CURRENT (mA) 09225-189 09225-169 AD5757 Data Sheet 10 0 20mA OUTPUT 10mA OUTPUT AV = 15V DD 8 V = 15V BOOST –20 T = 25°C A 6 4 –40 2 0 –60 –2 –80 –4 –6 –100 0mA TO 24mA RANGE AV = 5V 1kΩ LOAD –8 CC f = 410kHz EXTERNAL R SW SET INDUCTOR = 10µH (XAL4040-103) T = 25°C A –10 –120 0 2 4 6 8 10 12 14 10 100 1k 10k 100k 1M 10M FREQUENCY (Hz) TIME (µs) Figure 30. Output Current vs. Time with DC-to-DC Converter (See Figure 56) Figure 32. I PSRR vs. Frequency OUT_x 8 0mA TO 24mA RANGE 7 1kΩ LOAD f = 410kHz SW INDUCTOR = 10µH (XAL4040-103) 6 T = 25°C A 5 4 3 2 1 0 0 5 10 15 20 CURRENT (mA) Figure 31. DC-to-DC Converter Headroom vs. Output Current (See Figure 56) Rev. C | Page 18 of 44 CURRENT (AC COUPLED) (µA) HEADROOM VOLTAGE (V) 09225-067 09225-170 I PSRR (dB) OUT_x 09225-068 Data Sheet AD5757 DC-TO-DC BLOCK 90 80 AV = 4.5V 20mA CC 85 AV = 5V CC AV = 5.5V 70 CC 80 60 75 70 50 65 40 0mA TO 24mA RANGE 0mA TO 24mA RANGE 1kΩ LOAD 1kΩ LOAD 60 EXTERNAL R EXTERNAL R SET SET f = 410kHz AV = 5V 30 SW CC 55 INDUCTOR = 10µH (XAL4040-103) f = 410 kHz SW T = 25°C INDUCTOR = 10µH (XAL4040-103) A 50 20 0 4 8 12 16 20 24 –40 –20 0 20 40 60 80 100 CURRENT (mA) TEMPERATURE (°C) Figure 33. Efficiency at VBOOST_x vs. Output Current (See Figure 56) Figure 36. Output Efficiency vs. Temperature (See Figure 56) 0.6 90 20mA 85 0.5 80 0.4 75 70 0.3 65 0mA TO 24mA RANGE 0.2 1kΩ LOAD EXTERNAL R 60 SET AV = 5V CC f = 410kHz 0.1 SW 55 INDUCTOR = 10µH (XAL4040-103) 50 0 –40 –20 0 20 40 60 80 100 –40 –20 0 20 40 60 80 100 TEMPERATURE (°C) TEMPERATURE (°C) Figure 34. Efficiency at V vs. Temperature (See Figure 56) BOOST_x Figure 37. Switch Resistance vs. Temperature 80 AV = 4.5V CC AV = 5V CC AV = 5.5V 70 CC 60 50 40 0mA TO 24mA RANGE 1kΩ LOAD EXTERNAL R SET 30 f = 410kHz SW INDUCTOR = 10µH (XAL4040-103) T = 25°C A 20 0 4 8 12 16 20 24 CURRENT (mA) Figure 35. Output Efficiency vs. Output Current (See Figure 56) Rev. C | Page 19 of 44 I EFFICIENCY (%) V EFFICIENCY (%) OUT_x BOOST_x V EFFICIENCY (%) BOOST_x 09225-017 09225-018 09225-016 I EFFICIENCY (%) SWITCH RESISTANCE (Ω) OUT_x 09225-123 09225-019 AD5757 Data Sheet REFERENCE 16 5.0050 AV DD 30 DEVICES SHOWN 5.0045 14 REF OUT AV = 15V DD T = 25°C A 5.0040 12 5.0035 10 5.0030 8 5.0025 6 5.0020 4 5.0015 2 5.0010 0 5.0005 –2 5.0000 –40 –20 0 20 40 60 80 100 0 0.2 0.4 0.6 0.8 1.0 1.2 TIME (ms) TEMPERATURE (°C) Figure 38. REFOUT Turn-On Transient Figure 41. REFOUT vs. Temperature (When the AD5757 is soldered onto a PCB, the reference shifts due to thermal shock on the package. The average output voltage shift is –4 mV. Measurement of these parts after seven days shows that the outputs typically shift back 2 mV toward their initial values. This second shift is due to the relaxation of stress incurred during soldering.) 4 5.002 AV = 15V AV = 15V DD DD T = 25°C T = 25°C 3 A 5.001 A 5.000 2 1 4.999 0 4.998 4.997 –1 4.996 –2 4.995 –3 0 2 4 6 8 10 0 2 4 6 8 10 LOAD CURRENT (mA) TIME (s) Figure 39. REFOUT Output Noise (0.1 Hz to 10 Hz Bandwidth) Figure 42. REFOUT vs. Load Current 150 5.00000 AV = 15V DD T = 25°C A T = 25°C A 4.99995 100 4.99990 50 4.99985 0 4.99980 4.99975 –50 4.99970 –100 4.99965 –150 4.99960 0 5 10 15 20 10 15 20 25 30 TIME (ms) AV (V) DD Figure 40. REFOUT Output Noise (100 kHz Bandwidth) Figure 43. REFOUT vs. Supply Rev. C | Page 20 of 44 REFOUT (µV) REFOUT (µV) VOLTAGE (V) 09225-012 09225-011 09225-010 REFOUT (V) REFOUT (V) REFOUT (V) 09225-014 09225-163 09225-015 Data Sheet AD5757 GENERAL 450 13.4 DV = 5V CC 400 T = 25°C 13.3 A 350 13.2 300 13.1 250 13.0 200 12.9 150 12.8 100 12.7 DV = 5.5V 50 CC 0 12.6 0 1 2 3 4 5 –40 –20 0 20 40 60 80 100 SDIN VOLTAGE (V) TEMPERATURE (°C) Figure 44. DICC vs. Logic Input Voltage Figure 46. Internal Oscillator Frequency vs. Temperature 8 14.4 7 14.2 6 14.0 5 13.8 4 13.6 3 13.4 2 AI DD T = 25°C 13.2 A DV = 5.5V 1 CC I = 0mA OUT T = 25°C A 13.0 0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 10 15 20 25 30 VOLTAGE (V) VOLTAGE (V) Figure 47. Internal Oscillator Frequency vs. DV Supply Voltage Figure 45. AI vs. AV CC DD DD Rev. C | Page 21 of 44 CURRENT (mA) DI (µA) CC 09225-009 09225-007 FREQUENCY (MHz) FREQUENCY (MHz) 09225-020 09225-021 AD5757 Data Sheet TERMINOLOGY Current Loop Compliance Voltage Relative Accuracy or Integral Nonlinearity (INL) The maximum voltage at the IOUT_x pin for which the output For the DAC, relative accuracy, or integral nonlinearity, is a current is equal to the programmed value. measure of the maximum deviation, in LSBs, from the best fit line through the DAC transfer function. A typical INL vs. code Voltage Reference Thermal Hysteresis plot is shown in Figure 8. Voltage reference thermal hysteresis is the difference in output voltage measured at +25°C compared to the output voltage Differential Nonlinearity (DNL) measured at +25°C after cycling the temperature from +25°C to Differential nonlinearity (DNL) is the difference between the −40°C to +105°C and back to +25°C. The hysteresis is specified measured change and the ideal 1 LSB change between any two for the first and second temperature cycles and is expressed in ppm. adjacent codes. A specified differential nonlinearity of ±1 LSB maximum ensures monotonicity. This DAC is guaranteed Power-On Glitch Energy monotonic by design. A typical DNL vs. code plot is shown in Power-on glitch energy is the impulse injected into the analog Figure 9. output when the AD5757 is powered-on. It is specified as the area of the glitch in nV-sec. See Figure 24. Monotonicity A DAC is monotonic if the output either increases or remains Power Supply Rejection Ratio (PSRR) constant for increasing digital input code. The AD5757 is PSRR indicates how the output of the DAC is affected by monotonic over its full operating temperature range. changes in the power supply voltage. Offset Error Reference TC Offset error is the deviation of the analog output from the ideal Reference TC is a measure of the change in the reference output zero-scale output when all DAC registers are loaded with voltage with a change in temperature. It is expressed in ppm/°C. 0x0000. Line Regulation Gain Error Line regulation is the change in reference output voltage due to This is a measure of the span error of the DAC. It is the devia- a specified change in supply voltage. It is expressed in ppm/V. tion in slope of the DAC transfer characteristic from the ideal, Load Regulation expressed in % FSR. Load regulation is the change in reference output voltage due to Gain TC a specified change in load current. It is expressed in ppm/mA. This is a measure of the change in gain error with changes in DC-to-DC Converter Headroom temperature. Gain TC is expressed in ppm FSR/°C. This is the difference between the voltage required at the Full-Scale Error current output and the voltage supplied by the dc-to-dc Full-Scale error is a measure of the output error when full-scale converter. See Figure 31. code is loaded to the DAC register. Ideally, the output should be Output Efficiency full-scale − 1 LSB. Full-scale error is expressed in percent of 2 I × R LOAD OUT full-scale range (% FSR). AV × AI CC CC Full-Scale TC This is defined as the power delivered to a channel’s load vs. the Full-scale TC is a measure of the change in full-scale error with power delivered to the channel’s dc-to-dc input. changes in temperature and is expressed in ppm FSR/°C. Efficiency at V Total Unadjusted Error BOOST_x I ×V Total unadjusted error (TUE) is a measure of the output error OUT BOOST _ x taking all the various errors into account, including INL error, AV × AI CC CC offset error, gain error, temperature, and time. TUE is expressed This is defined as the power delivered to a channel’s V BOOST_x in % FSR. supply vs. the power delivered to the channel’s dc-to-dc input. DC Crosstalk The V quiescent current is considered part of the dc-to- BOOST_x This is the dc change in the output level of one DAC in response dc converter’s losses. to a change in the output of another DAC. It is measured with a full-scale output change on one DAC while monitoring another DAC, which is at midscale. Rev. C | Page 22 of 44 Data Sheet AD5757 THEORY OF OPERATION The AD5757 is a quad, precision digital-to-current loop POWER-ON STATE OF THE AD5757 converter designed to meet the requirements of industrial On power-up of the AD5757, the I pins are in tristate mode. OUT_x process control applications. It provides a high precision, fully After device power-on or a device reset, it is recommended to integrated, low cost, single-chip solution for generating current wait 100 μs or more before writing to the device to allow time loop outputs. The current ranges available are 0 mA to 20 mA, for internal calibrations to take place. 0 mA to 24 mA, and 4 mA to 20 mA. The desired output configuration is user selectable via the DAC control register. SERIAL INTERFACE On-chip dynamic power control minimizes package power The AD5757 is controlled over a versatile 3-wire serial interface dissipation in current mode. that operates at clock rates of up to 30 MHz and is compatible with SPI, QSPI, MICROWIRE, and DSP standards. Data coding DAC ARCHITECTURE is always straight binary. The DAC core architecture of the AD5757 consists of two Input Shift Register matched DAC sections. A simplified circuit diagram is shown The input shift register is 24 bits wide. Data is loaded into the in Figure 48. The four MSBs of the 16-bit data-word are device MSB first as a 24-bit word under the control of a serial decoded to drive 15 switches, E1 to E15. Each of these switches connects one of 15 matched resistors to either ground or the clock input, SCLK. Data is clocked in on the falling edge of SCLK. reference buffer output. The remaining 12 bits of the data-word If packet error checking, or PEC (see the Device Features drive Switch S0 to Switch S11 of a 12-bit voltage mode R-2R section), is enabled, an additional eight bits must be written to ladder network. the AD5757, creating a 32-bit serial interface. V OUT There are two ways in which the DAC outputs can be updated: 2R 2R 2R 2R 2R 2R 2R individual updating or simultaneous updating of all DACs. S0 S1 S11 E1 E2 E15 Individual DAC Updating In this mode, LDAC is held low while data is being clocked into the DAC data register. The addressed DAC output is updated on 12-BIT R-2-R LADDER FOUR MSBs DECODED INTO SYNC the rising edge of . See Table 3 and Figure 3 for timing 15 EQUAL SEGMENTS information. Figure 48. DAC Ladder Structure Simultaneous Updating of All DACs The voltage output from the DAC core is converted to a current In this mode, LDAC is held high while data is being clocked (see Figure 49), which is then mirrored to the supply rail so that into the DAC data register. Only the first write to each channel’s the application simply sees a current source output. The current LDAC is brought high. Any subse- DAC data register is valid after outputs are supplied by VBOOST_x. LDAC quent writes while is still held high are ignored, although V BOOST_x they are loaded into the DAC data register. All the DAC outputs LDAC SYNC are updated by taking low after is taken high. R2 R3 OUTPUT I/V AMPLIFIER T2 V 16-BIT REFIN V OUT_x A2 DAC T1 16-BIT DAC I A1 OUT_x DAC LDAC REGISTER R SET DAC INPUT REGISTER Figure 49. Voltage-to-Current Conversion Circuitry OFFSET AND GAIN Reference Buffers CALIBRATION DAC DATA REGISTER The AD5757 can operate with either an external or internal reference. The reference input requires a 5 V reference for specified performance. This input voltage is then buffered SCLK INTERFACE SDO SYNC before it is applied to the DAC. LOGIC SDIN Figure 50. Simplified Serial Interface of Input Loading Circuitry for One DAC Channel Rev. C | Page 23 of 44 09225-071 09225-069 09225-072 AD5757 Data Sheet TRANSFER FUNCTION For the 0 mA to 20 mA, 0 mA to 24 mA, and 4 mA to 20 mA current output ranges, the output current is respectively expressed as 20 mA I = × D OUT N 2 24 mA I = × D OUT N 2 16 mA I = × D+ 4 mA OUT N 2 where: D is the decimal equivalent of the code loaded to the DAC. N is the bit resolution of the DAC. Rev. C | Page 24 of 44 Data Sheet AD5757 REGISTERS Table 6 shows an overview of the registers for the AD5757. Table 6. Data, Control, and Readback Registers for the AD5757 Register Description Data DAC Data Register (×4) Used to write a DAC code to each DAC channel. AD5757 data bits = D15 to D0. There are four DAC data registers, one per DAC channel. Gain Register (×4) Used to program gain trim, on a per channel basis. AD5757 data bits = D15 to D0. There are four gain registers, one per DAC channel. Offset Register (×4) Used to program offset trim, on a per channel basis. AD5757 data bits = D15 to D0. There are four offset registers, one per DAC channel. Clear Code Register (×4) Used to program clear code on a per channel basis. AD5757 data bits = D15 to D0. There are four clear code registers, one per DAC channel. Control Main Control Register Used to configure the part for main operation. Sets functions such as status readback during write, enables output on all channels simultaneously, powers on all dc-to-dc converter blocks simultaneously, and enables and sets conditions of the watchdog timer. See the Device Features section for more details. Software Register Has three functions. Used to perform a reset, to toggle the user bit and, as part of the watchdog timer feature, to verify correct data communication operation. Slew Rate Control Register (×4) Used to program the slew rate of the output. There are four slew rate control registers, one per channel. DAC Control Register (×4) These registers are used to control the following: Set the output range, for example, 4 mA to 20 mA. Set whether an internal/external sense resistor is used. Enable/disable a channel for CLEAR. Enable/disable internal circuitry on a per channel basis. Enable/disable output on a per channel basis. Power on dc-to-dc converters on a per channel basis. There are four DAC control registers, one per DAC channel. DC-to-DC Control Register Use to set the dc-to-dc control parameters. Can control dc-to-dc maximum voltage, phase, and frequency. Readback Status Register This contains any fault information, as well as a user toggle bit. Rev. C | Page 25 of 44 AD5757 Data Sheet PROGRAMMING SEQUENCE TO WRITE/ENABLE CHANGING AND REPROGRAMMING THE RANGE THE OUTPUT CORRECTLY When changing between ranges, the same sequence as To correctly write to and set up the part from a power-on described in the Programming Sequence to Write/Enable the Output Correctly section should be used. It is recommended to condition, use the following sequence: set the range to zero scale prior to disabling the output. Because 1. Perform a hardware or software reset after initial power-on. the dc-to-dc switching frequency, maximum voltage, and phase 2. The dc-to-dc converter supply block must be configured. have already been selected, there is no need to reprogram these. Set the dc-to-dc switching frequency, maximum output A flowchart of this sequence is shown in Figure 52. voltage allowed, and the phase that the four dc-to-dc channels clock at. CHANNEL’S OUTPUT IS ENABLED. 3. Configure the DAC control register on a per channel basis. The output range is selected, and the dc-to-dc converter STEP 1: WRITE TO CHANNEL’S DAC DATA block is enabled (DC_DC bit). Other control bits can be REGISTER. SET THE OUTPUT TO 0V (ZERO OR MIDSCALE). configured at this point. Set the INT_ENABLE bit; however, the output enable bit (OUTEN) should not be set. STEP 2: WRITE TO DAC CONTROL REGISTER. 4. Write the required code to the DAC data register. This DISABLE THE OUTPUT (OUTEN = 0), AND SET THE NEW OUTPUT RANGE. KEEP THE implements a full DAC calibration internally. Allow at least DC_DC BIT AND THE INT_ENABLE BIT SET. 200 µs before Step 5 for reduced output glitch. 5. Write to the DAC control register again to enable the STEP 3: WRITE VALUE TO THE DAC DATA REGISTER. output (set the OUTEN bit). A flowchart of this sequence is shown in Figure 51. STEP 4: WRITE TO DAC CONTROL REGISTER. RELOAD SEQUENCE AS IN STEP 2 ABOVE. THIS TIME SELECT THE OUTEN BIT TO POWER ON. ENABLE THE OUTPUT. Figure 52. Steps for Changing the Output Range STEP 1: PERFORM A SOFTWARE/HARDWARE RESET. STEP 2: WRITE TO DC-TO-DC CONTROL REGISTER TO SET DC-TO-DC CLOCK FREQUENCY, PHASE, AND MAXIMUM VOLTAGE. STEP 3: WRITE TO DAC CONTROL REGISTER. SELECT THE DAC CHANNEL AND OUTPUT RANGE. SET THE DC_DC BIT AND OTHER CONTROL BITS AS REQUIRED. SET THE INT_ENABLE BIT BUT DO NOT SELECT THE OUTEN BIT. STEP 4: WRITE TO EACH/ALL DAC DATA REGISTERS. ALLOW AT LEAST 200µs BETWEEN STEP 3 AND STEP 5 FOR REDUCED OUTPUT GLITCH. STEP 5: WRITE TO DAC CONTROL REGISTER. RELOAD SEQUENCE AS IN STEP 3 ABOVE. THIS TIME SELECT THE OUTEN BIT TO ENABLE THE OUTPUT. Figure 51. Programming Sequence for Enabling the Output Correctly Rev. C | Page 26 of 44 09225-073 09225-074 Data Sheet AD5757 DATA REGISTERS The input register is 24 bits wide. When PEC is enabled, the DAC Data Register input register is 32 bits wide, with the last eight bits correspond- When writing to the AD5757 DAC data registers, D15 to D0 are ing to the PEC code (see the Packet Error Checking section for used for the DAC data bits. Table 9 shows the register format more information on PEC). When writing to a data register, the and Table 8 describes the function of Bit D23 to Bit D16. format in Table 7 must be used. Table 7. Writing to a Data Register MSB LSB D23 D22 D21 D20 D19 D18 D17 D16 D15 to D0 R/ DUT_AD1 DUT_AD0 DREG2 DREG1 DREG0 DAC_AD1 DAC_AD0 Data W Table 8. Input Register Decode Bit Description R/W Indicates a read from or a write to the addressed register. DUT_AD1, DUT_AD0 Used in association with the external pins, AD1 and AD0, to determine which AD5757 device is being addressed by the system controller. DUT_AD1 DUT_AD0 Function 0 0 Addresses part with Pin AD1 = 0, Pin AD0 = 0 0 1 Addresses part with Pin AD1 = 0, Pin AD0 = 1 1 0 Addresses part with Pin AD1 = 1, Pin AD0 = 0 1 1 Addresses part with Pin AD1 = 1, Pin AD0 = 1 DREG2, DREG1, DREG0 Selects whether a data register or a control register is written to. If a control register is selected, a further decode of CREG bits (see Table 16) is required to select the particular control register, as follows. DREG2 DREG1 DREG0 Function 0 0 0 Write to DAC data register (individual channel write) 0 1 0 Write to gain register 0 1 1 Write to gain register (all DACs) 1 0 0 Write to offset register 1 0 1 Write to offset register (all DACs) 1 1 0 Write to clear code register 1 1 1 Write to a control register DAC_AD1, DAC_AD0 These bits are used to decode the DAC channel. DAC_AD1 DAC_AD0 DAC Channel/Register Address 0 0 DAC A 0 1 DAC B 1 0 DAC C 1 1 DAC D X X These are don’t cares if they are not relevant to the operation being performed. Table 9. Programming the DAC Data Registers MSB LSB D23 D22 D21 D20 D19 D18 D17 D16 D15 to D0 R/W DUT_AD1 DUT_AD0 DREG2 DREG1 DREG0 DAC_AD1 DAC_AD0 DAC data Rev. C | Page 27 of 44 AD5757 Data Sheet Gain Register Offset Register The 16-bit gain register, as shown in Table 10, allows the user to The 16-bit offset register, as shown in Table 12, allows the user to adjust the gain of each channel in steps of 1 LSB. This is done by adjust the offset of each channel by −32,768 LSBs to +32,767 LSBs setting the DREG[2:0] bits to 010. It is possible to write the in steps of 1 LSB. This is done by setting the DREG[2:0] bits to same gain code to all four DAC channels at the same time by 100. It is possible to write the same offset code to all four DAC setting the DREG[2:0] bits to 011. The gain register coding is channels at the same time by setting the DREG[2:0] bits to 101. straight binary as shown in Table 11. The default code in the The offset register coding is straight binary as shown in Table 13. gain register is 0xFFFF. In theory, the gain can be tuned across The default code in the offset register is 0x8000, which results in the full range of the output. In practice, the maximum recom- zero offset programmed to the output. See the Digital Offset mended gain trim is about 50% of programmed range to maintain and Gain Control section for more information. accuracy. See the Digital Offset and Gain Control section for Clear Code Register more information. The 16-bit clear code register allows the user to set the clear value of each channel as shown in Table 14. It is possible, via software, to enable or disable on a per channel basis which channels are cleared when the CLEAR pin is activated. The default clear code is 0x0000. See the Asynchronous Clear section for more information. Table 10. Programming the Gain Register R/W DUT_AD1 DUT_AD0 DREG2 DREG1 DREG0 DAC_AD1 DAC_AD0 D15 to D0 0 Device address 0 1 0 DAC channel address Gain adjustment Table 11. Gain Register Gain Adjustment G15 G14 G13 G12 to G4 G3 G2 G1 G0 +65,535 LSBs 1 1 1 1 1 1 1 1 +65,534 LSBs 1 1 1 1 1 1 0 0 … … … … … … … … … 1 LSB 0 0 0 0 0 0 0 1 0 LSBs 0 0 0 0 0 0 0 0 Table 12. Programming the Offset Register R/W DUT_AD1 DUT_AD0 DREG2 DREG1 DREG0 DAC_AD1 DAC_AD0 D15 to D0 0 Device address 1 0 0 DAC channel address Offset adjustment Table 13. Offset Register Options Offset Adjustment OF15 OF14 OF13 OF12 to OF4 OF3 OF2 OF1 OF0 +32,767 LSBs 1 1 1 1 1 1 1 1 +32,766 LSBs 1 1 1 1 1 1 0 0 … … … … … … … … … No Adjustment (Default) 1 0 0 0 0 0 0 0 … … … … … … … … … −32,767 LSBs 0 0 0 0 0 0 0 0 −32,768 LSBs 0 0 0 0 0 0 0 0 Table 14. Programming the Clear Code Register R/W DUT_AD1 DUT_AD0 DREG2 DREG1 DREG0 DAC_AD1 DAC_AD0 D15 to D0 0 Device address 1 1 0 DAC channel address Clear code Rev. C | Page 28 of 44 Data Sheet AD5757 CONTROL REGISTERS When writing to a control register, the format shown in Table 15 Main Control Register must be used. See Table 8 for information on the configuration The main control register options are shown in Table 17 and of Bit D23 to Bit D16. The control registers are addressed by setting Table 18. See the Device Features section for more information the DREG[2:0] bits to 111 and then setting the CREG[2:0] bits on the features controlled by the main Control Register. to the appropriate decode address for that register, according to Table 16. These CREG bits select among the various control registers. Table 15. Writing to a Control Register MSB LSB D23 D22 D21 D20 D19 D18 D17 D16 D15 D14 D13 D12 to D0 R/W DUT_AD1 DUT_AD0 1 1 1 DAC_AD1 DAC_AD0 CREG2 CREG1 CREG0 Data Table 16. Register Access Decode CREG2 (D15) CREG1 (D14) CREG0 (D13) Function 0 0 0 Slew rate control register (one per channel) 0 0 1 Main control register 0 1 0 DAC control register (one per channel) 0 1 1 DC-to-dc control register 1 0 0 Software register Table 17. Programming the Main Control Register MSB LSB D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 to D0 1 1 1 0 0 1 0 STATREAD EWD WD1 WD0 X X OUTEN_ALL DCDC_ALL X 1 X = don’t care. Table 18. Main Control Register Functions Bit Description STATREAD Enable status readback during a write. See the Device Features section. STATREAD = 1, enable. STATREAD = 0, disable (default). EWD Enable watchdog timer. See the Device Features section for more information. EWD = 1, enable watchdog. EWD = 0, disable watchdog (default). WD1, WD0 Timeout select bits. Used to select the timeout period for the watchdog timer. WD1 WD0 Timeout Period (ms) 0 0 5 0 1 10 1 0 100 1 1 200 OUTEN_ALL Enables the output on all four DACs simultaneously. Do not use the OUTEN_ALL bit when using the OUTEN bit in the DAC control register. DCDC_ALL When set, powers up the dc-to-dc converter on all four channels simultaneously. To power down the dc-to-dc converters, all channel outputs must first be disabled. Do not use the DCDC_ALL bit when using the DC_DC bit in the DAC control register. Rev. C | Page 29 of 44 AD5757 Data Sheet DAC Control Register The DAC control register is used to configure each DAC channel. The DAC control register options are shown in Table 19 and Table 20. Table 19. Programming DAC Control Register D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 1 1 1 1 1 0 1 0 X X X X INT_ENABLE CLR_EN OUTEN RSET DC_DC X R2 R1 R0 1 X = don’t care. Table 20. DAC Control Register Functions Bit Description INT_ENABLE Powers up the dc-to-dc converter, DAC, and internal amplifiers for the selected channel. Does not enable the output. Can only be done on a per channel basis. It is recommended to set this bit and allow a >200 µs delay before enabling the output because this results in a reduced output enable glitch. Plots of this glitch can be found in Figure 25. CLR_EN Per channel clear enable bit. Selects if this channel clears when the CLEAR pin is activated. CLR_EN = 1, channel clears when the part is cleared. CLR_EN = 0, channel does not clear when the part is cleared (default). OUTEN Enables/disables the selected output channel. OUTEN = 1, enables the channel. OUTEN = 0, disables the channel (default). RSET Selects an internal or external current sense resistor for the selected DAC channel. RSET = 0, selects the external resistor (default). RSET = 1, selects the internal resistor. DC_DC Powers the dc-to-dc converter on the selected channel. DC_DC = 1, power up the dc-to-dc converter. DC_DC = 0, power down the dc-to-dc converter (default). This allows per channel dc-to-dc converter power-up/power-down. To power down the dc-to-dc converter, the OUTEN and INT_ENABLE bits must also be set to 0. All dc-to-dc converters can also be powered up simultaneously using the DCDC_ALL bit in the main control register. R2, R1, R0 Selects the output range to be enabled. R2 R1 R0 Output Range Selected 1 0 0 4 mA to 20 mA current range 1 0 1 0 mA to 20 mA current range 1 1 0 0 mA to 24 mA current range Rev. C | Page 30 of 44 Data Sheet AD5757 Software Register When the watchdog feature is enabled, the user must write 0x195 to the software register within the timeout period. If this The software register has three functions. It allows the user to command is not received within the timeout period, the ALERT perform a software reset to the part. It can be used to set the pin signals a fault condition. This is only required when the user toggle bit, D11, in the status register. It is also used as part watchdog timer function is enabled. of the watchdog feature when it is enabled. This feature is useful to ensure that communication has not been lost between the DC-to-DC Control Register MCU and the AD5757 and that the datapath lines are working The dc-to-dc control register allows the user control over properly (that is, SDIN, SCLK, and SYNC). the dc-to-dc switching frequency and phase, as well as the maximum allowable dc-to-dc output voltage. The dc-to-dc control register options are shown in Table 23 and Table 24. Table 21. Programming the Software Register MSB LSB D15 D14 D13 D12 D11 to D0 1 0 0 User program Reset code/SPI code Table 22. Software Register Functions Bit Description User Program This bit is mapped to Bit D11 of the status register. When this bit is set to 1, Bit D11 of the status register is set to 1. Likewise, when D12 is set to 0, Bit D11 of the status register is also set to zero. This feature can be used to ensure that the SPI pins are working correctly by writing a known bit value to this register and reading back the corresponding bit from the status register. Reset Code/SPI Code Option Description Reset code Writing 0x555 to D[11:0] performs a reset of the AD5757. SPI code If the watchdog timer feature is enabled, 0x195 must be written to the software register (D11 to D0) within the programmed timeout period. Table 23. Programming the DC-to-DC Control Register MSB LSB D15 D14 D13 D12 to D7 D6 D5 to D4 D3 to D2 D1 to D0 1 0 1 1 X DC-DC Comp DC-DC phase DC-DC Freq DC-DC MaxV 1 X = don’t care. Table 24. DC-to-DC Control Register Options Bit Description DC-DC Comp Selects between an internal and external compensation resistor for the dc-to-dc converter. See the DC-to-DC Converter Compensation Capacitors and AICC Supply Requirements—Slewing sections in the Device Features section for more information. 0 = selects the internal 150 kΩ compensation resistor (default). 1 = bypasses the internal compensation resistor for the dc-to-dc converter. In this mode, an external dc-to-dc compensation resistor must be used; this is placed at the COMP pin in series with the 10 nF dc-to-dc compensation DCDC_x capacitor to ground. Typically, a ~50 kΩ resistor is recommended. DC-DC Phase User programmable dc-to-dc converter phase (between channels). 00 = all dc-to-dc converters clock on the same edge (default). 01 = Channel A and Channel B clock on the same edge, Channel C and Channel D clock on opposite edges. 10 = Channel A and Channel C clock on the same edge, Channel B and Channel D clock on opposite edges. 11 = Channel A, Channel B, Channel C, and Channel D clock 90° out of phase from each other. DC-DC Freq DC-to-dc switching frequency; these are divided down from the internal 13 MHz oscillator (see Figure 46 and Figure 47). 00 = 250 ± 10% kHz. 01 = 410 ± 10% kHz (default). 10 = 650 ± 10% kHz. DC-DC MaxV Maximum allowed VBOOST_x voltage supplied by the dc-to-dc converter. 00 = 23 V + 1 V/−1.5 V (default). 01 = 24.5 V ± 1 V. 10 = 27 V ± 1 V. 11 = 29.5 V ± 1V. Rev. C | Page 31 of 44 AD5757 Data Sheet Slew Rate Control Register no operation command. The no operation command for DUT_AD[1:0] = 00 is 0x1CE000; for other DUT addresses, This register is used to program the slew rate control for the Bit D22 and Bit D21 are set accordingly. selected DAC channel. The slew rate control is enabled/ disabled and programmed on a per channel basis. See Table 25 Readback Example and the Digital Slew Rate Control section for more information. To read back the gain register of Device 1, Channel A on the AD5757, implement the following sequence: READBACK OPERATION 1. Write 0xA80000 to the AD5757 input register. This Readback mode is invoked by setting the R/W bit = 1 in the configures the AD5757 Device Address 1 for read mode serial input register write. See Table 26 for the bits associated with the gain register of Channel A selected. All the data with a readback operation. The DUT_AD1 and DUT_AD0 bits, bits, D15 to D0, are don’t cares. in association with Bits RD[4:0], select the register to be read. 2. Follow with another read command or a no operation The remaining data bits in the write sequence are don’t cares. command (0x3CE000). During this command, the data During the next SPI transfer (see Figure 4), the data appearing from the Channel A gain register is clocked out on the on the SDO output contains the data from the previously SDO line. addressed register. This second SPI transfer should either be a request to read yet another register on a third data transfer or a Table 25. Programming the Slew Rate Control Register D15 D14 D13 D12 D11 to D7 D6 to D3 D2 to D0 1 0 0 0 SREN X SR_CLOCK SR_STEP 1 X = don’t care. Table 26. Input Shift Register Contents for a Read Operation D23 D22 D21 D20 D19 D18 D17 D16 D15 to D0 1 R/ DUT_AD1 DUT_AD0 RD4 RD3 RD2 RD1 RD0 X W 1 X = don’t care. Table 27. Read Address Decoding RD4 RD3 RD2 RD1 RD0 Function 0 0 0 0 0 Read DAC A data register 0 0 0 0 1 Read DAC B data register 0 0 0 1 0 Read DAC C data register 0 0 0 1 1 Read DAC D data register 0 0 1 0 0 Read DAC A control register 0 0 1 0 1 Read DAC B control register 0 0 1 1 0 Read DAC C control register 0 0 1 1 1 Read DAC D control register 0 1 0 0 0 Read DAC A gain register 0 1 0 0 1 Read DAC B gain register 0 1 0 1 0 Read DAC C gain register 0 1 0 1 1 Read DAC D gain register 0 1 1 0 0 Read DACA offset register 0 1 1 0 1 Read DAC B offset register 0 1 1 1 0 Read DAC C offset register 0 1 1 1 1 Read DAC D offset register 1 0 0 0 0 Clear DAC A code register 1 0 0 0 1 Clear DAC B code register 1 0 0 1 0 Clear DAC C code register 1 0 0 1 1 Clear DAC D code register 1 0 1 0 0 DAC A slew rate control register 1 0 1 0 1 DAC B slew rate control register 1 0 1 1 0 DAC C slew rate control register 1 0 1 1 1 DAC D slew rate control register 1 1 0 0 0 Read status register 1 1 0 0 1 Read main control register 1 1 0 1 0 Read dc-to-dc control register Rev. C | Page 32 of 44 Data Sheet AD5757 Status Register register is set, the status register contents can be read back on the SDO pin during every write sequence. Alternatively, if the The status register is a read only register. This register contains STATREAD bit is not set, the status register can be read using any fault information as a well as a ramp active bit and a user the normal readback operation. toggle bit. When the STATREAD bit in the main control Table 28. Decoding the Status Register MSB LSB D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 1 1 1 1 DC- DC- DC- DC- User PEC Ramp Over X X X X I I I I OUT_D OUT_C OUT_B OUT_A DCD DCC DCB DCA toggle error active TEMP fault fault fault fault 1 X = don’t care. Table 29. Status Register Options Bit Description DC-DCD This bit is set on Channel D if the dc-to-dc converter cannot maintain compliance (it may be reaching its V MAX voltage). In this case, the I fault bit is also set. See the DC-to-DC Converter V Functionality section for more OUT_D MAX information on this bit’s operation under this condition. DC-DCC This bit is set on Channel C if the dc-to-dc converter cannot maintain compliance (it may be reaching its VMAX voltage). In this case, the IOUT_C fault bit is also set. See the DC-to-DC Converter VMAX Functionality section for more information on this bit’s operation under this condition. DC-DCB This bit is set on Channel B if the dc-to-dc converter cannot maintain compliance (it may be reaching its V MAX voltage). In this case, the I fault bit is also set. See the DC-to-DC Converter V Functionality section for more OUT_B MAX information on this bit’s operation under this condition. DC-DCA This bit is set on Channel A if the dc-to-dc converter cannot maintain compliance (it may be reaching its VMAX voltage). In this case, the IOUT_A fault bit is also set. See the DC-to-DC Converter VMAX Functionality section for more information on this bit’s operation under this condition. User toggle User toggle bit. This bit is set or cleared via the software register. This can be used to verify data communications if needed. PEC Error Denotes a PEC error on the last data-word received over the SPI interface. Ramp Active This bit is set while any one of the output channels is slewing (slew rate control is enabled on at least one channel). Over TEMP This bit is set if the AD5757 core temperature exceeds approximately 150°C. I Fault This bit is set if a fault is detected on the I pin. OUT_D OUT_D I Fault This bit is set if a fault is detected on the I pin. OUT_C OUT_C I Fault This bit is set if a fault is detected on the I pin. OUT_B OUT_B IOUT_A Fault This bit is set if a fault is detected on the IOUT_A pin. Rev. C | Page 33 of 44 AD5757 Data Sheet DEVICE FEATURES Theory of Operation section. Both the gain register and the OUTPUT FAULT offset register have 16 bits of resolution. The correct method to FAULT The AD5757 is equipped with a pin, an active low open- calibrate the gain/offset is to first calibrate out the gain and then drain output allowing several AD5757 devices to be connected calibrate the offset. together to one pull-up resistor for global fault detection. The The value (in decimal) that is written to the DAC input register FAULT pin is forced active by any one of the following fault can be calculated by scenarios: (M+ 1) • The voltage at IOUT_x attempts to rise above the compliance 15 Code = D× + C− 2 (1) DACRegister 16 range, due to an open-loop circuit or insufficient power 2 supply voltage. The internal circuitry that develops the where: fault output avoids using a comparator with windowed D is the code loaded to the DAC channel’s input register. limits because this requires an actual output error before 16 M is the code in the gain register (default code = 2 – 1). FAULT the output becomes active. Instead, the signal is 15 C is the code in the offset register (default code = 2 ). generated when the internal amplifier in the output stage STATUS READBACK DURING A WRITE has less than approximately 1 V of remaining drive The AD5757 has the ability to read back the status register capability. Thus, the FAULT output activates slightly before contents during every write sequence. This feature is enabled the compliance limit is reached. via the STATREAD bit in the main control register. This allows • An interface error is detected due to a PEC failure. See the the user to continuously monitor the status register and act Packet Error Checking section. quickly in the case of a fault. • If the core temperature of the AD5757 exceeds approximately 150°C. When status readback during a write is enabled, the contents of the 16-bit status register (see Table 29) are output on the SDO The I fault, PEC error, and over TEMP bits of the status OUT_x pin, as shown in Figure 5. FAULT register are used in conjunction with the output to The AD5757 powers up with this feature disabled. When this is inform the user which one of the fault conditions caused the enabled, the normal readback feature is not available, except for FAULT output to be activated. the status register. To read back any other register, clear the DIGITAL OFFSET AND GAIN CONTROL STATREAD bit first before following the readback sequence. Each DAC channel has a gain (M) and offset (C) register, which STATREAD can be set high again after the register read. allow trimming out of the gain and offset errors of the entire ASYNCHRONOUS CLEAR signal chain. Data from the DAC data register is operated on by CLEAR is an active high, edge-sensitive input that allows the a digital multiplier and adder controlled by the contents of the output to be cleared to a preprogrammed 16-bit code. This code M and C registers. The calibrated DAC data is then stored in the is user programmable via a per channel 16-bit clear code register. DAC input register. For a channel to clear, that channel must be enabled to be INPUT DAC DAC REGISTER REGISTER cleared via the CLR_EN bit in the channel’s DAC control register. If the channel is not enabled to be cleared, the output M remains in its current state independent of the CLEAR pin level. REGISTER When the CLEAR signal is returned low, the relevant outputs C REGISTER remain cleared until a new value is programmed. Figure 53. Digital Offset and Gain control PACKET ERROR CHECKING Although Figure 53 indicates a multiplier and adder for each To verify that data has been received correctly in noisy environ- channel, there is only one multiplier and one adder in the device, ments, the AD5757 offers the option of packet error checking and they are shared among all four channels. This has based on an 8-bit cyclic redundancy check (CRC-8). The device implications for the update speed when several channels are controlling the AD5757 should generate an 8-bit frame check updated at once (see Table 3). sequence using the polynomial Each time data is written to the M or C register, the output is C(x) = x8 + x2 + x1 + 1 not automatically updated. Instead, the next write to the DAC This is added to the end of the data-word, and 32 bits are sent channel uses these M and C values to perform a new calibration SYNC to the AD5757 before taking high. If the AD5757 sees a and automatically updates the channel. SYNC 32-bit frame, it performs the error check when goes high. The output data from the calibration is routed to the DAC input If the check is valid, the data is written to the selected register. register. This is then loaded to the DAC as described in the Rev. C | Page 34 of 44 09225-075 Data Sheet AD5757 FAULT If the error check fails, the pin goes low and the PEC INTERNAL REFERENCE error bit in the status register is set. After reading the status The AD5757 contains an integrated 5 V voltage reference with register, FAULT returns high (assuming there are no other initial accuracy of ±5 mV maximum and a temperature drift faults), and the PEC error bit is cleared automatically. coefficient of ±10 ppm maximum. The reference voltage UPDATE ON SYNC HIGH is buffered and externally available for use elsewhere within SYNC the system. EXTERNAL CURRENT SETTING RESISTOR SCLK Referring to Figure 49, RSET is an internal sense resistor as part MSB LSB D23 D0 of the voltage to current conversion circuitry. The stability of SDIN 24-BIT DATA the output current value over temperature is dependent on the stability of the value of R . As a method of improving the SET 24-BIT DATA TRANSFER—NO ERROR CHECKING stability of the output current over temperature, an external 15 kΩ low drift resistor can be connected to the RSET_x pin of UPDATE ON SYNC HIGH SYNC ONLY IF ERROR CHECK PASSED the AD5757 to be used instead of the internal resistor, R1. The external resistor is selected via the DAC control register (see Table 19). SCLK MSB LSB Table 1 outlines the performance specifications of the AD5757 D31 D8 D7 D0 with both the internal R resistor and an external, 15 kΩ R SET SET SDIN 24-BIT DATA 8-BIT CRC resistor. Using an external RSET resistor allows for improved performance over the internal RSET resistor option. The external FAULT PIN GOES LOW RSET resistor specification assumes an ideal resistor; the actual FAULT IF ERROR CHECK FAILS performance depends on the absolute value and temperature 32-BIT DATA TRANSFER WITH ERROR CHECKING coefficient of the resistor used. This directly affects the gain error Figure 54. PEC Timing of the output, and thus the total unadjusted error. To arrive at The PEC can be used for both transmit and receive of data the gain/TUE error of the output with a particular external R SET packets. If status readback during a write is enabled, the PEC resistor, add the percentage absolute error of the R resistor SET values returned during the status readback during a write directly to the gain/TUE error of the AD5757 with the external operation should be ignored. If status readback during a write is RSET resistor, shown in Table 1 (expressed in % FSR). disabled, the user can still use the normal readback operation to HART monitor status register activity with PEC. The AD5757 has four CHART pins, one corresponding to each WATCHDOG TIMER output channels. A HART signal can be coupled into these pins. When enabled, an on-chip watchdog timer generates an alert The HART signal appears on the corresponding current output, signal if 0x195 has not been written to the software register if the output is enabled. Table 30 shows the recommended input within the programmed timeout period. This feature is useful voltages for the HART signal at the CHART pin. If these to ensure that communication has not been lost between the voltages are used, the current output should meet the HART MCU and the AD5757 and that these datapath lines are working amplitude specifications. Figure 55 shows the recommended SYNC properly (that is, SDIN, SCLK, and ). If 0x195 is not circuit for attenuating and coupling in the HART signal. received by the software register within the timeout period, Table 30. CHART Input Voltage to HART Output Current the ALERT pin signals a fault condition. The ALERT signal is CHART Input Current Output active high and can be connected directly to the CLEAR pin to RSET Voltage (HART) enable a CLEAR in the event that communication from the Internal R 150 mV p-p 1 mA p-p SET MCU is lost. External RSET 170 mV p-p 1 mA p-p The watchdog timer is enabled, and the timeout period (5 ms, C1 10 ms, 100 ms, or 200 ms) is set in the main control register (see CHARTx Table 17 and Table 18). C2 HART MODEM OUTPUT OUTPUT ALERT Figure 55. Coupling HART Signal The AD5757 is equipped with an ALERT pin. This is an active A minimum capacitance of C1 + C2 is required to ensure that high CMOS output. The AD5757 also has an internal watchdog the 1.2 kHz and 2.2 kHz HART frequencies are not significantly timer. When enabled, it monitors SPI communications. If 0x195 attenuated at the output. The recommended values are C1 = is not received by the software register within the timeout period, 22 nF, C2 = 47 nF. the ALERT pin goes active. Rev. C | Page 35 of 44 09225-008 09225-076 AD5757 Data Sheet Digitally controlling the slew rate of the output is necessary to The following equation describes the slew rate as a function of meet the analog rate of change requirements for HART. the step size, the update clock frequency, and the LSB size: DIGITAL SLEW RATE CONTROL Slew Time= The slew rate control feature of the AD5757 allows the user to Output Change control the rate at which the output value changes. With the Step Size×Update Clock Frequency× LSB Size slew rate control feature disabled, the output value changes at a rate limited by the output drive circuitry and the attached load. where: To reduce the slew rate, this can be achieved by enabling the Slew Time is expressed in seconds. slew rate control feature. With the feature enabled via the SREN Output Change is expressed in amps for IOUT_x. bit of the slew rate control register (see Table 25), the output, When the slew rate control feature is enabled, all output instead of slewing directly between two values, steps digitally at changes occur at the programmed slew rate (see the DC-to-DC a rate defined by two parameters accessible via the slew rate Converter Settling Time section for additional information). control register, as shown in Table 25. The parameters are For example, if the CLEAR pin is asserted, the output slews to SR_CLOCK and SR_STEP. SR_CLOCK defines the rate at the clear value at the programmed slew rate (assuming that the which the digital slew is updated, for example, if the selected clear channel is enabled to be cleared). If a number of channels update rate is 8 kHz, the output updates every 125 µs. In conjunc- are enabled for slew, care must be taken when asserting the tion with this, SR_STEP defines by how much the output value CLEAR pin. If one of the channels is slewing when CLEAR is changes at each update. Together, both parameters define the asserted, other channels may change directly to their clear rate of change of the output value. Table 31 and Table 32 outline values not under slew rate control. The update clock frequency the range of values for both the SR_CLOCK and SR_STEP for any given value is the same for all output ranges. The step parameters. size, however, varies across output ranges for a given value of step size because the LSB size is different for each output range. Table 31. Slew Rate Update Clock Options 1 SR_CLOCK Update Clock Frequency (Hz) POWER DISSIPATION CONTROL 0000 64 k The AD5757 contains integrated dynamic power control using 0001 32 k a dc-to-dc boost converter circuit, allowing reductions in power 0010 16 k consumption from standard designs. 0011 8 k In standard current input module designs, the load resistor 0100 4 k values can range from typically 50 Ω to 750 Ω. Output module 0101 2 k systems must source enough voltage to meet the compliance 0110 1 k voltage requirement across the full range of load resistor values. 0111 500 For example, in a 4 mA to 20 mA loop when driving 20 mA, a 1000 250 compliance voltage of >15 V is required. When driving 20 mA 1001 125 into a 50 Ω load, only 1 V compliance is required. 1010 64 1011 32 The AD5757 circuitry senses the output voltage and regulates 1100 16 this voltage to meet compliance requirements plus a small 1101 8 headroom voltage. The AD5757 is capable of driving up to 1110 4 24 mA through a 1 kΩ load. 1111 0.5 DC-TO-DC CONVERTERS 1 These clock frequencies are divided down from the 13 MHz internal The AD5757 contains four independent dc-to-dc converters. oscillator. See Table 1, Figure 46, and Figure 47. These are used to provide dynamic control of the VBOOST supply voltage for each channel (see Figure 49). Figure 56 shows the Table 32. Slew Rate Step Size Options discrete components needed for the dc-to-dc circuitry, and the SR_STEP Step Size (LSBs) following sections describe component selection and operation 000 1 of this circuitry. 001 2 L D R DCDC DCDC FILTER 010 4 AV V CC BOOST_X 10µH 10Ω 011 16 C IN C C FILTER DCDC ≥10µF 0.1µF 4.7µF 100 32 SWx 101 64 Figure 56. DC-to-DC Circuit 110 128 111 256 Rev. C | Page 36 of 44 09225-077 Data Sheet AD5757 29.6 Table 33. Recommended DC-to-DC Components V 0mA TO 24mA RANGE, 24mA OUTPUT MAX OUTPUT UNLOADED DC_DC BIT Symbol Component Value Manufacturer 29.5 LDCDC XAL4040-103 10 µH Coilcraft® 29.4 CDCDC GRM32ER71H475KA88L 4.7 µF Murata 29.3 D PMEG3010BEA 0.38 V NXP DCDC F 29.2 It is recommended to place a 10 Ω, 100 nF low-pass RC filter 29.1 after CDCDC. This consumes a small amount of power but DC-DCMaxV = 29.5V DC-DCx BIT = 1 29.0 reduces the amount of ripple on the VBOOST_x supply. f = 410kHz SW 28.9 DC-to-DC Converter Operation T = 25°C A 28.8 The on-board dc-to-dc converters use a constant frequency, peak current mode control scheme to step up an AVCC input of 28.7 DC-DCx BIT = 0 4.5 V to 5.5 V to drive the AD5757 output channel. These are 28.6 designed to operate in discontinuous conduction mode (DCM) 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 TIME (ms) with a duty cycle of <90% typical. Discontinuous conduction Figure 57. Operation on Reaching VMAX mode refers to a mode of operation where the inductor current goes to zero for an appreciable percentage of the switching As shown in Figure 57, the DC-DCx bit in the status register cycle. The dc-to-dc converters are nonsynchronous; that is, asserts when the AD5757 is ramping to the VMAX value but they require an external Schottky diode. deasserts when the voltage is decaying to VMAX − ~0.4 V. DC-to-DC Converter Output Voltage DC-to-DC Converter On-Board Switch When a channel current output is enabled, the converter regulates The AD5757 contains a 0.425 Ω internal switch. The switch the V supply to 7.4 V (±5%) or (I × R + Headroom), BOOST_x OUT LOAD current is monitored on a pulse by pulse basis and is limited to whichever is greater (see Figure 31 for a plot of headroom 0.8 A peak current. supplied vs. output current). When the output is disabled, the DC-to-DC Converter Switching Frequency and Phase converter regulates the VBOOST_x supply to 7.4 V (±5%). The AD5757 dc-to-dc converter switching frequency can be DC-to-DC Converter Settling Time selected from the dc-to-dc control register. The phasing of the The settling time for a step greater than ~1 V (I × R ) is OUT LOAD channels can also be adjusted so that the dc-to-dc converter can dominated by the settling time of the dc-to-dc converter. The clock on different edges (see Table 24). For typical applications, exception to this is when the required voltage at the I pin plus OUT_x a 410 kHz frequency is recommended. At light loads (low output the compliance voltage is below 7.4 V (±5%). A typical plot of the current and small load resistor), the dc-to-dc converter enters a output settling time can be found in Figure 26. This plot is for a pulse-skipping mode to minimize switching power dissipation. 1 kΩ load. The settling time for smaller loads is faster. The DC-to-DC Converter Inductor Selection settling time for current steps less than 24 mA is also faster. For typical 4 mA to 20 mA applications, a 10 µH inductor (such DC-to-DC Converter V Functionality MAX as the XAL4040-103 from Coilcraft), combined with a switch- The maximum V voltage is set in the dc-to-dc control BOOST_x ing frequency of 410 kHz, allows up to 24 mA to be driven into a register (23 V, 24.5 V, 27 V, or 29.5 V; see Table 24). On reaching load resistance of up to 1 kΩ with an AVCC supply of 4.5 V to this maximum voltage, the dc-to-dc converter is disabled, and 5.5 V. It is important to ensure that the inductor is able to handle the VBOOST_x voltage is allowed to decay by ~0.4 V. After the the peak current without saturating, especially at the maximum VBOOST_x voltage has decayed by ~0.4 V, the dc-to-dc converter ambient temperature. If the inductor enters into saturation mode, is reenabled, and the voltage ramps up again to V , if still MAX it results in a decrease in efficiency. The inductance value also required. This operation is shown in Figure 57. drops during saturation and may result in the dc-to-dc converter circuit not being able to supply the required output power. DC-to-DC Converter External Schottky Selection The AD5757 requires an external Schottky for correct operation. Ensure that the Schottky is rated to handle the maximum reverse breakdown expected in operation and that the rectifier maximum junction temperature is not exceeded. The diode average current is approximately equal to the ILOAD current. Diodes with larger forward voltage drops result in a decrease in efficiency. Rev. C | Page 37 of 44 V VOLTAGE (mV) BOOST 09225-183 AD5757 Data Sheet DC-to-DC Converter Compensation Capacitors AI SUPPLY REQUIREMENTS—SLEWING CC As the dc-to-dc converter operates in DCM, the uncompensated The AICC current requirement while slewing is greater than in transfer function is essentially a single-pole transfer function. static operation because the output power increases to charge The pole frequency of the transfer function is determined by the output capacitance of the dc-to-dc converter. This transient the dc-to-dc converter’s output capacitance, input and output current can be quite large (see Figure 58), although the methods voltage, and output load. The AD5757 uses an external capaci- described in the Reducing AI Current Requirements section CC tor in conjunction with an internal 150 kΩ resistor to compensate can reduce the requirements on the AV supply. If not enough CC the regulator loop. Alternatively, an external compensation AICC current can be provided, the AVCC voltage drops. Due to resistor can be used in series with the compensation capacitor this AVCC drop, the AICC current required to slew increases by setting the DC-DC Comp bit in the dc-to-dc control register. further. This means that the voltage at AVCC drops further (see In this case, a ~50 kΩ resistor is recommended. A description Equation 3) and the VBOOST_x voltage, and thus the output volt- of the advantages of this can be found in the AICC Supply age, may never reach its intended value. Because this AV CC Requirements—Slewing section. For typical applications, a voltage is common to all channels, this may also affect other 10 nF dc-to-dc compensation capacitor is recommended. channels. 0.8 DC-to-DC Converter Input and Output Capacitor 30 Selection 0.7 The output capacitor affects ripple voltage of the dc-to-dc con- 25 0.6 verter and indirectly limits the maximum slew rate at which the 0mA TO 24mA RANGE 1kΩ LOAD channel output current can rise. The ripple voltage is caused by 20 0.5 f = 410kHz SW INDUCTOR = 10µH (XAL4040-103) a combination of the capacitance and equivalent series resistance T = 25°C A 0.4 15 (ESR) of the capacitor. For the AD5757, a ceramic capacitor of 4.7 µF is recommended for typical applications. Larger 0.3 10 capacitors or paralleled capacitors improve the ripple at the 0.2 expense of reduced slew rate. Larger capacitors also impact AI CC 5 I the AV supplies current requirements while slewing (see the 0.1 OUT CC V BOOST AI Supply Requirements—Slewing section). This capacitance CC 0 0 at the output of the dc-to-dc converter should be >3 µF under 0 0.5 1.0 1.5 2.0 2.5 TIME (ms) all operating conditions. Figure 58. AICC Current vs. Time for 24 mA Step Through 1 kΩ Load The input capacitor provides much of the dynamic current with Internal Compensation Resistor required for the dc-to-dc converter and should be a low ESR Reducing AI Current Requirements CC component. For the AD5757, a low ESR tantalum or ceramic There are two main methods that can be used to reduce the capacitor of 10 µF is recommended for typical applications. AI current requirements. One method is to add an external CC Ceramic capacitors must be chosen carefully because they can compensation resistor, and the other is to use slew rate control. exhibit a large sensitivity to dc bias voltages and temperature. Both of these methods can be used in conjunction. X5R or X7R dielectrics are preferred because these capacitors remain stable over wider operating voltage and temperature A compensation resistor can be placed at the COMPDCDC_x pin ranges. Care must be taken if selecting a tantalum capacitor to in series with the 10 nF compensation capacitor. A 51 kΩ external ensure a low ESR value. compensation resistor is recommended. This compensation increases the slew time of the current output but eases the AICC AI SUPPLY REQUIREMENTS—STATIC CC transient current requirements. Figure 59 shows a plot of AI CC The dc-to-dc converter is designed to supply a VBOOST_x voltage of current for a 24 mA step through a 1 kΩ load when using a VBOOST = IOUT × RLOAD + Headroom (2) 51 kΩ compensation resistor. This method eases the current requirements through smaller loads even further, as shown in See Figure 31 for a plot of headroom supplied vs. output Figure 60. voltage. This means that, for a fixed load and output voltage, the dc-to-dc converter output current can be calculated by the following formula: Power Out I ×V OUT BOOST AI = = (3) CC Efficiency× AV η × AV CC V CC BOOST where: IOUT is the output current from IOUT_x in amps. ηV is the efficiency at VBOOST_x as a fraction (see Figure 33 BOOST and Figure 34). Rev. C | Page 38 of 44 AI CURRENT (A) CC I CURRENT (mA)/V VOLTAGE (V) OUT_x BOOST_x 09225-184 Data Sheet AD5757 0.8 0.8 32 32 0mA TO 24mA RANGE 0mA TO 24mA RANGE 1kΩ LOAD 1kΩ LOAD f = 410kHz 0.7 0.7 SW 28 28 f = 410kHz SW INDUCTOR = 10µH (XAL4040-103) INDUCTOR = 10µH (XAL4040-103) T = 25°C A T = 25°C A 0.6 0.6 24 24 AI CC 0.5 20 0.5 20 I OUT V BOOST 0.4 16 0.4 16 0.3 12 0.3 12 0.2 8 0.2 8 AI CC 0.1 I 4 0.1 4 OUT V BOOST 0 0 0 0 0 0.5 1.0 1.5 2.0 2.5 0 1 2 3 4 5 6 TIME (ms) TIME (ms) Current vs. Time for 24 mA Step Through 1 kΩ Load Current vs. Time for 24 mA Step Through 1 kΩ Load Figure 59. AICC Figure 61. AICC with External 51 kΩ Compensation Resistor with Slew Rate Control 0.8 32 EXTERNAL PMOS MODE AI CC 0mA TO 24mA RANGE I 0.7 28 OUT The AD5757 can also be used with an external PMOS transistor 500Ω LOAD V BOOST f = 410kHz SW per channel, as shown in Figure 62. This mode can be used to INDUCTOR = 10µH (XAL4040-103) 0.6 24 T = 25°C A limit the on-chip power dissipation of the AD5757, though this 0.5 20 will not reduce the power dissipation of the total system. The IGATE functionality is not typically required when using the 0.4 16 dynamic power control feature so Figure 62 shows the configura- 0.3 12 tion of the device for a fixed VBOOST_x supply. 0.2 8 In this configuration the SWx pin are left floating and the GNDSWx pin is grounded. The VBOOST_x pin is connected to a 0.1 4 minimum supply of 7.5 V and a maximum supply of 33 V. This 0 0 supply can be sized according to the maximum load required to 0 0.5 1.0 1.5 2.0 2.5 be driven. TIME (ms) Figure 60. AICC Current vs. Time for 24 mA Step Through 500 Ω Load The IGATE functionality works by holding the gate of the with External 51 kΩ Compensation Resistor external PMOS transistor at (VBOOST_x − 5 V). This means that Using slew rate control can greatly reduce the AVCC supplies cur- the majority of the channels power dissipation will take place in rent requirements, as shown in Figure 61. When using slew rate this external PMOS transistor. control, attention should be paid to the fact that the output cannot The external PMOS transistor should be chosen tolerate a V DS slew faster than the dc-to-dc converter. The dc-to-dc converter voltage of at least −V , as well as to handle the power BOOST_x slews slowest at higher currents through large (for example, 1 dissipation required. This external PMOS transistor typically kΩ) loads. This slew rate is also dependent on the configuration has minimal effect on the current output performance. of the dc-to-dc converter. Two examples of the dc-to-dc converter’s output slew are shown in Figure 59 and Figure 60 (VBOOST corre- sponds to the dc-to-dc converter’s output voltage). AV CC V 5.0V BOOST_A SW (LEFT FLOATING) A R2 R3 DAC A I OUT_A (V –5V) BOOST_A IGATEA CURRENT OUTPUT R1 R LOAD R SET_A CHARTA DAC CHANNEL A SWGND A Figure 62. Configuration off a Particular Channel Using IGATE Rev. C | Page 39 of 44 AI CURRENT (A) AI CURRENT (A) CC CC I CURRENT (mA)/V VOLTAGE (V) I CURRENT (mA)/V VOLTAGE (V) OUT_x BOOST_x OUT_x BOOST_x 09225-186 09225-185 AI CURRENT (A) CC 09225-190 I CURRENT (mA)/V VOLTAGE (V) OUT_x BOOST_x 09225-187 AD5757 Data Sheet APPLICATIONS INFORMATION There are four possible sources of error to consider when choosing CURRENT OUTPUT MODE WITH INTERNAL R SET a voltage reference for high accuracy applications: initial When using the internal R resistor in current output mode, SET accuracy, temperature coefficient of the output voltage, long- the output is significantly affected by how many other channels term drift, and output voltage noise. using the internal RSET are enabled and by the dc crosstalk from Initial accuracy error on the output voltage of an external refer- these channels. The internal RSET specifications in Table 1 are ence can lead to a full-scale error in the DAC. Therefore, to for all channels enabled with the internal RSET selected and minimize these errors, a reference with low initial accuracy outputting the same code. error specification is preferred. Choosing a reference with an For every channel enabled with the internal RSET, the offset error output trim adjustment, such as the ADR425, allows a system decreases. For example, with one current output enabled using designer to trim system errors out by setting the reference the internal R , the offset error is 0.075% FSR. This value SET voltage to a voltage other than the nominal. The trim adjust- decreases proportionally as more current channels are enabled; ment can be used at any temperature to trim out any error. the offset error is 0.056% FSR on each of two channels, 0.029% Long-term drift is a measure of how much the reference output on each of three channels, and 0.01% on each of four channels. voltage drifts over time. A reference with a tight long-term drift Similarly, the dc crosstalk when using the internal RSET is propor- specification ensures that the overall solution remains relatively tional to the number of current output channels enabled with stable over its entire lifetime. the internal RSET. For example, with the measured channel at 0x8000 and one channel going from zero to full scale, the dc The temperature coefficient of a reference’s output voltage affects crosstalk is −0.011% FSR. With two channels going from zero to INL, DNL, and TUE. A reference with a tight temperature full scale, it is −0.019% FSR, and with all three other channels coefficient specification should be chosen to reduce the depend- ence of the DAC output voltage to ambient temperature. going from zero to full scale, it is −0.025% FSR. In high accuracy applications, which have a relatively low noise For the full-scale error measurement in Table 1, all channels are budget, reference output voltage noise must be considered. at 0xFFFF. This means that, as any channel goes to zero scale, Choosing a reference with as low an output noise voltage as practi- the full-scale error increases due to the dc crosstalk. For example, cal for the system resolution required is important. Precision with the measured channel at 0xFFFF and three channels at zero scale, the full-scale error is 0.025%. Similarly, if only one voltage references such as the ADR435 (XFET design) produce channel is enabled in current output mode with the internal low output noise in the 0.1 Hz to 10 Hz region. However, as the R circuit bandwidth increases, filtering the output of the reference SET, the full-scale error is 0.025% FSR + 0.075% FSR = 0.1% FSR. may be required to minimize the output noise. PRECISION VOLTAGE REFERENCE SELECTION DRIVING INDUCTIVE LOADS To achieve the optimum performance from the AD5757 over its full operating temperature range, a precision voltage reference When driving inductive or poorly defined loads, a capacitor may be required between I and AGND to ensure stability. A must be used. Thought should be given to the selection of a OUT_x 0.01 µF capacitor between I and AGND ensures stability of precision voltage reference. The voltage applied to the reference OUT_x a load of 50 mH. The capacitive component of the load may inputs is used to provide a buffered reference for the DAC cores. cause slower settling, although this may be masked by the set- Therefore, any error in the voltage reference is reflected in the outputs of the device. tling time of the AD5757. There is no maximum capacitance limit for the current output of the AD5757. Table 34. Recommended Precision References Initial Accuracy Long-Term Drift 0.1 Hz to 10 Hz Noise Part No. (mV Maximum) (ppm Typical) Temperature Drift (ppm/°C Maximum) (µV p-p Typical) ADR445 ±2 50 3 2.25 ADR02 ±3 50 3 10 ADR435 ±2 40 3 8 ADR395 ±5 50 9 8 AD586 ±2.5 15 10 4 Rev. C | Page 40 of 44 Data Sheet AD5757 TRANSIENT VOLTAGE PROTECTION AD5757 SPORT_TFS SYNC The AD5757 contains ESD protection diodes that prevent dam- SPORT_TSCK SCLK age from normal handling. The industrial control environment SPORT_DTO SDIN can, however, subject I/O circuits to much higher transients. To protect the AD5757 from excessively high voltage transients, external power diodes and a surge current limiting resistor (R ) P ADSP-BF527 GPIO0 LDAC are required, as shown in Figure 63. A typical value for R is 10 Ω. P The two protection diodes and the resistor (RP) must have appro- Figure 64. AD5757-to-ADSP-BF527 SPORT Interface priate power ratings. (FROM LAYOUT GUIDELINES R DC-TO-DC FILTER CONVERTER) Grounding 10Ω C FILTER C DCDC 0.1µF In any circuit where accuracy is important, careful consideration 4.7µF of the power supply and ground return layout helps to ensure V BOOST_x the rated performance. The printed circuit board on which the D1 AD5757 R P AD5757 is mounted should be designed so that the analog and I OUT_x digital sections are separated and confined to certain areas of the AGND R D2 LOAD board. If the AD5757 is in a system where multiple devices require an AGND-to-DGND connection, the connection should Figure 63. Output Transient Voltage Protection be made at one point only. The star ground point should be Additional protection can be provided using transient voltage established as close as possible to the device. suppressors (TVSs), also referred to as transorbs. These compo- The GNDSW and ground connection for the AV supply are x CC nents are available as unidirectional suppressors, which protect referred to as PGND. PGND should be confined to certain areas against positive high voltage transients, and as bidirectional of the board, and the PGND-to-AGND connection should be suppressors, which protect against both positive and negative made at one point only. high voltage transients. Transient voltage suppressors are avail- Supply Decoupling able in a wide range of standoff and breakdown voltage ratings. The TVS should be sized with the lowest breakdown voltage The AD5757 should have ample supply bypassing of 10 µF possible while not conducting in the functional range of the in parallel with 0.1 µF on each supply located as close to the current output. package as possible, ideally right up against the device. The 10 µF capacitors are the tantalum bead type. The 0.1 µF capaci- It is recommended that all field connected nodes be protected. tor should have low effective series resistance (ESR) and low MICROPROCESSOR INTERFACING effective series inductance (ESL), such as the common ceramic Microprocessor interfacing to the AD5757 is via a serial bus that types, which provide a low impedance path to ground at high uses a protocol compatible with microcontrollers and DSP frequencies to handle transient currents due to internal logic processors. The communications channel is a 3-wire minimum switching. interface consisting of a clock signal, a data signal, and a latch Traces signal. The AD5757 requires a 24-bit data-word with data valid The power supply lines of the AD5757 should use as large a on the falling edge of SCLK. trace as possible to provide low impedance paths and reduce the The DAC output update is initiated on either the rising edge of effects of glitches on the power supply line. Fast switching signals LDAC LDAC SYNC or, if is held low, on the rising edge of . The such as clocks should be shielded with digital ground to prevent contents of the registers can be read using the readback function. radiating noise to other parts of the board and should never be run near the reference inputs. A ground line routed between the AD5757-TO-ADSP-BF527 INTERFACE SDIN and SCLK lines helps reduce crosstalk between them (not The AD5757 can be connected directly to the SPORT interface required on a multilayer board that has a separate ground plane, of the ADSP-BF527, an Analog Devices, Inc., Blackfin® DSP. but separating the lines helps). It is essential to minimize noise Figure 64 shows how the SPORT interface can be connected to on the REFIN line because it couples through to the DAC output. control the AD5757. Avoid crossover of digital and analog signals. Traces on opposite sides of the board should run at right angles to each other. This reduces the effects of feedthrough on the board. A microstrip technique is by far the best but not always possible with a double-sided board. In this technique, the component side of the board is dedicated to ground plane, whereas signal traces are placed on the solder side. Rev. C | Page 41 of 44 09225-013 09225-080 AD5757 Data Sheet DC-to-DC Converters GALVANICALLY ISOLATED INTERFACE To achieve high efficiency, good regulation, and stability, a well- In many process control applications, it is necessary to provide designed printed circuit board layout is required. an isolation barrier between the controller and the unit being controlled to protect and isolate the controlling circuitry from Follow these guidelines when designing printed circuit boards any hazardous common-mode voltages that may occur. Analog (see Figure 56): Devices iCoupler® products can provide voltage isolation in • Keep the low ESR input capacitor, CIN, close to AVCC excess of 2.5 kV. The serial loading structure of the AD5757 and PGND. makes it ideal for isolated interfaces because the number of • Keep the high current path from CIN through the inductor, interface lines is kept to a minimum. Figure 65 shows a 4-channel L , to SW and PGND as short as possible. DCDC X isolated interface to the AD5757 using an ADuM1400. For • Keep the high current path from C through L and the IN DCDC more information, visit www.analog.com. rectifier, D , to the output capacitor, C , as short as DCDC DCDC MICROCONTROLLER ADuM1400* possible. V V OA IA SERIAL CLOCK ENCODE DECODE TO SCLK OUT • Keep high current traces as short and as wide as possible. V V IB OB SERIAL DATA The path from CIN through the inductor, LDCDC, to SWX and ENCODE DECODE TO SDIN OUT PGND should be able to handle a minimum of 1 A. V V OC IC SYNC OUT ENCODE DECODE TO SYNC • Place the compensation components as close as possible to V V COMPDCDC_x. ID OD CONTROL OUT ENCODE DECODE TO LDAC • Avoid routing high impedance traces near any node *ADDITIONAL PINS OMITTED FOR CLARITY. connected to SWx or near the inductor to prevent radiated Figure 65. Isolated Interface noise injection. Rev. C | Page 42 of 44 09225-081 Data Sheet AD5757 adheres to the HART physical layer specifications as defined by INDUSTRIAL HART CAPABLE ANALOG OUTPUT the HART Communication Foundation. APPLICATION For transient overvoltage protection, a 24 V transient voltage sup- Many industrial control applications have requirements for pressor (TVS) is placed on the IOUT/VOUT connection. For added accurately controlled current output signals, and the AD5757 is protection, clamping diodes are connected from the IOUT_x/VOUT_x ideal for such applications. Figure 67 shows the AD5757 in a pin to the AVDD and GND power supply pins. A 5 kΩ current circuit design for a HART-enabled output module, specifically limiting resistor is also placed in series with the +VSENSE_X for use in an industrial control application. input. This is to limit the current to an acceptable level during a The design provides for a HART-enabled current output, with transient event. The recommended external band-pass filter for the HART capability provided by the AD5700/AD5700-1 HART the AD5700 HART modem includes a 150 kΩ resistor, which modem, the industry’s lowest power and smallest footprint HART- limits current to a sufficiently low level to adhere to intrinsic safety compliant IC modem. For additional space-savings, the AD5700-1 requirements. In this case, the input has higher transient voltage offers a 0.5% precision internal oscillator. The HART_OUT signal protection and should, therefore, not require additional protection from the AD5700 is attenuated and ac-coupled into the CHARTx circuitry, even in the most demanding of industrial environments. pin of the AD5757. Such a configuration results in the AD5700 HART modem output modulating the 4 mA to 20 mA analog current without affecting the dc level of the current. This circuit 10µF +15V +15V 0.1µF 2.7V TO 5.5V V (X4) AV AV SW(X4) DV DD CC BOOST DD 10µF 10kΩ IOUT B,C,D 0.1µF RESET ALERT CHART B,C,D FAULT CLEAR SYNC AD5757 D2 MCU SCLK R P SDIN IOUTA SDO 4.20mA D3 D1 CURRENTLOOP UART INTERFACE LDAC R L DGND REFOUT REFIN CHART A GND 0.1µF 0.1µF 22nF 47nF C1 C2 V CC TXD HART_OUT RXD RTS CD AD5700/AD5700-1 REF 1µF 1.2MQ 150kΩ ADC_IP GND 1.2MQ 300pF 150pF Figure 66. AD5757 in HART Configuration Rev. C | Page 43 of 44 09225-065 AD5757 Data Sheet OUTLINE DIMENSIONS 9.10 9.00 SQ 0.60 MAX 8.90 0.60 PIN 1 MAX INDICATOR 49 64 1 48 PIN 1 INDICATOR 8.85 0.50 EXPOSED 7.25 PAD 8.75 SQ BSC 7.10 SQ 8.65 6.95 0.50 16 33 0.40 17 32 0.30 0.25 MIN BOTTOM VIEW TOP VIEW 7.50 REF 0.80 MAX 12° MAX 1.00 0.65 TYP 0.85 0.05 MAX FOR PROPER CONNECTION OF 0.80 THE EXPOSED PAD, REFER TO 0.02 NOM THE PIN CONFIGURATION AND 0.30 FUNCTION DESCRIPTIONS SEATING 0.20 REF SECTION OF THIS DATA SHEET. PLANE 0.23 0.18 COMPLIANT TO JEDEC STANDARDS MO-220-VMMD-4 Figure 67. 64-Lead Lead Frame Chip Scale Package [LFCSP_VQ] 9 mm × 9 mm Body, Very Thin Quad (CP-64-3) Dimensions shown in millimeters ORDERING GUIDE 1 Model Resolution (Bits) Temperature Range Package Description Package Option AD5757ACPZ 16 −40°C to +105°C 64-Lead Lead Frame Chip Scale Package [LFCSP_VQ] CP-64-3 AD5757ACPZ-REEL7 16 −40°C to +105°C 64-Lead Lead Frame Chip Scale Package [LFCSP_VQ] CP-64-3 EVAL-AD5757SDZ Evaluation Board 1 Z = RoHS Compliant Part. ©2011–2012 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D09225-0-5/12(C) Rev. C | Page 44 of 44 04-10-2012-C
Frequently asked questions
What makes Elite.Parts unique?
What kind of warranty will the AD5757 have?
Which carriers does Elite.Parts work with?
Will Elite.Parts sell to me even though I live outside the USA?
I have a preferred payment method. Will Elite.Parts accept it?
Why buy from GID?
Quality
We are industry veterans who take pride in our work
Protection
Avoid the dangers of risky trading in the gray market
Access
Our network of suppliers is ready and at your disposal
Savings
Maintain legacy systems to prevent costly downtime
Speed
Time is of the essence, and we are respectful of yours
Manufacturers


What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods