Elite.Parts Manufacturers A ANALOG DEVICES AD5755-1
About product Specifications Features Datasheet FAQ

ANALOG DEVICES AD5755-1

Description

Analog Devices AD5755-1 Quad Channel, 16-Bit, Serial Input 4-20MA & Voltage Output DAC

Part Number

AD5755-1

Price

Request Quote

Manufacturer

ANALOG DEVICES

Lead Time

Request Quote

Category

PRODUCTS - A

Specifications

DAC Input Format

SPI

DAC Settling Time

11µs

DAC Type

I or V Out

DAC Update Rate

91kSPS

Max Pos Supply (V)

+33V

Resolution (Bits)

16bit

Single-Supply

No

Features

Datasheet

pdf file

AD5755-1-715424705.pdf

1508 KiB

Extracted Text

Quad Channel, 16-Bit, Serial Input, 4 mA to 20 mA and Voltage Output DAC, Dynamic Power Control, HART Connectivity Data Sheet AD5755-1 in current mode. This is achieved by regulating the voltage on FEATURES the output driver from 7.4 V to 29.5 V using a dc-to-dc boost 16-bit resolution and monotonicity converter optimized for minimum on-chip power dissipation. Dynamic power control for thermal management Each channel has a corresponding CHART pin so that HART Current and voltage output pins connectable to a single signals can be coupled onto the current output of the AD5755-1. terminal Current output ranges: 0 mA to 20 mA, 4 mA to 20 mA, The part uses a versatile 3-wire serial interface that operates at or 0 mA to 24 mA clock rates of up to 30 MHz and is compatible with standard ±0.05% total unadjusted error (TUE) maximum SPI, QSPI™, MICROWIRE™, DSP, and microcontroller interface Voltage output ranges (with 20% overrange): 0 V to 5 V, 0 V standards. The interface also features optional CRC-8 packet to 10 V, ±5 V, and ±10 V error checking, as well as a watchdog timer that monitors ±0.04% total unadjusted error (TUE) maximum activity on the interface. User programmable offset and gain PRODUCT HIGHLIGHTS On-chip diagnostics 1. Dynamic power control for thermal management. On-chip reference (±10 ppm/°C maximum) 2. 16-bit performance. −40°C to +105°C temperature range 3. Multichannel. APPLICATIONS 4. HART compliant. Process control COMPANION PRODUCTS Actuator control PLCs Product Family: AD5755, AD5757 HART network connectivity HART Modem: AD5700, AD5700-1 External References: ADR445, ADR02 GENERAL DESCRIPTION Digital Isolators: ADuM1410, ADuM1411 The AD5755-1 is a quad, voltage and current output DAC that Power: ADP2302, ADP2303 operates with a power supply range from −26.4 V to +33 V. On- Additional companion products on the AD5755-1 product page chip dynamic power control minimizes package power dissipation FUNCTIONAL BLOCK DIAGRAM AV CC 5.0V AV AV SS DD –15V/0V AGND +15V SW V x BOOST_x DV 7.4V TO 29.5V DD DGND DC-TO-DC LDAC CONVERTER SCLK SDIN SYNC DIGITAL I OUT_x INTERFACE SDO R + DAC A SET_x CLEAR CURRENT AND CHARTx VOLTAGE FAULT OUTPUT RANGE SCALING ALERT GAIN REG A +V SENSE_x AD1 OFFSET REG A V OUT _x AD0 DAC CHANNEL A REFOUT REFERENCE REFIN DAC CHANNEL B DAC CHANNEL C AD5755-1 DAC CHANNEL D NOTES 1. x = A, B, C, AND D. Figure 1. Rev. C Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. rights of third parties that may result from its use. Specifications subject to change without notice. No Tel: 781.329.4700 www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. Fax: 781.461.3113 ©2011–2012 Analog Devices, Inc. All rights reserved. 09226-101 AD5755-1 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 Device Features ............................................................................... 40 Applications ....................................................................................... 1 Output Fault ................................................................................ 40 General Description ......................................................................... 1 Voltage Output Short-Circuit Protection ................................ 40 Product Highlights ........................................................................... 1 Digital Offset and Gain Control ............................................... 40 Companion Products ....................................................................... 1 Status Readback During a Write .............................................. 40 Functional Block Diagram .............................................................. 1 Asynchronous Clear ................................................................... 41 Revision History ............................................................................... 3 Packet Error Checking ............................................................... 41 Detailed Functional Block Diagram .............................................. 4 Watchdog Timer ......................................................................... 41 Specifications ..................................................................................... 5 Output Alert ................................................................................ 41 AC Performance Characteristics ................................................ 8 Internal Reference ...................................................................... 41 Timing Characteristics ................................................................ 9 External Current Setting Resistor ............................................ 41 Absolute Maximum Ratings .......................................................... 12 HART ........................................................................................... 42 ESD Caution ................................................................................ 12 Digital Slew Rate Control .......................................................... 42 Pin Configuration and Function Descriptions ........................... 13 Power Dissipation control ......................................................... 43 Typical Performance Characteristics ........................................... 16 DC-to-DC Converters ............................................................... 43 Voltage Outputs .......................................................................... 16 AICC Supply Requirements—Static .......................................... 44 Current Outputs ......................................................................... 20 AICC Supply Requirements—Slewing ...................................... 44 DC-to-DC Block ......................................................................... 24 Applications Information .............................................................. 46 Reference ..................................................................................... 25 Voltage and Current Output Ranges on the Same Terminal ...................................................................................... 46 General ......................................................................................... 26 Current Output Mode with Internal R ................................ 46 SET Terminology .................................................................................... 27 Precision Voltage Reference Selection ..................................... 46 Theory of Operation ...................................................................... 29 Driving Inductive Loads ............................................................ 47 DAC Architecture ....................................................................... 29 Transient Voltage Protection .................................................... 47 Power-On State of the AD5755-1 ............................................. 29 Microprocessor Interfacing ....................................................... 47 Serial Interface ............................................................................ 30 Layout Guidelines....................................................................... 47 Transfer Function ....................................................................... 30 Galvanically Isolated Interface ................................................. 48 Registers ........................................................................................... 31 Industrial HART Capable Analog Output Application— Programming Sequence to Write/Enable the Output Shared V and I Pin ...................................................... 49 OUT_x OUT_x Correctly ...................................................................................... 32 Outline Dimensions ....................................................................... 50 Changing and Reprogramming the Range ............................. 32 Ordering Guide .......................................................................... 50 Data Registers ............................................................................. 33 Control Registers ........................................................................ 35 Readback Operation................................................................... 38 Rev. C | Page 2 of 52 Data Sheet AD5755-1 Changes to Figure 44 ...................................................................... 22 REVISION HISTORY Changes to Figure 71 ...................................................................... 29 5/12—Rev. B to Rev. C Changes to Power-On State of the AD5755-1 Section ............... 30 Changes to Companion Products Section ..................................... 1 Changes to Table 17 ........................................................................ 35 Changes to Figure 2........................................................................... 3 Changes to Readback Operation section and Table 26 .............. 38 Changes to Table 5 .......................................................................... 15 Changes to Voltage Output Short-Circuit Protection Section .. 40 Changes to Figure 22 ...................................................................... 18 Changes to Figure 78 ...................................................................... 41 Added Industrial HART Capable Analog Output Application— Changes to Figure 82 ...................................................................... 44 Shared VOUT_x and IOUT_X Pin Section and Figure 89, Changes to Figure 83, Figure 84, and Figure 85 .................................. 45 Renumbered Sequentially .............................................................. 49 Changes to Transient Voltage Protection Section and Figure 86 ... 47 Updated Outline Dimensions ........................................................ 50 Changes to Galvanically Isolated Interface Section .................... 48 11/11—Rev. A to Rev. B 5/11—Rev. 0 to Rev. A Removed Voltage Output Test Conditions/Comments, Table 1 .... 5 Removed Endnote 6 (Table 1) ......................................................... 6 Changed Headroom and Footroom Test Conditions/Comments, Changed AVDD Minimum Value from 10.8 V to 9 V ................... 6 Table 1 .............................................................................................................. 5 Changed AI Minimum Value from −1.4 mA to −1.7 mA......... 7 SS Changes to Figure 4......................................................................... 10 Changed AV Voltage in Pin 19 Description ............................ 13 DD Changes to Figure 5......................................................................... 11 Changes to Ordering Guide ........................................................... 48 Changes to SCLK Description, Table 5 ........................................ 13 4/11—Revision 0: Initial Version Changes to Figure 12 ...................................................................... 16 Changes to Figure 21 ...................................................................... 18 Changes to Figure 37 ...................................................................... 20 Rev. C | Page 3 of 52 AD5755-1 Data Sheet DETAILED FUNCTIONAL BLOCK DIAGRAM AV CC 5.0V AV AV SS DD –15V/0V AGND +15V SW V A BOOST_A DV POWER-ON DD DC-TO-DC RESET CONVERTER DGND V V SEN1 SEN2 POWER 7.4V TO 29.5V LDAC CONTROL REG CLEAR INPUT SHIFT SCLK REGISTER R2 R3 16 16 INPUT DAC AND SDIN DAC A REG A REG A CONTROL SYNC SDO FAULT GAIN REG A I OUT_A OFFSET REG A STATUS REGISTER R1 WATCHDOG ALERT R SET_A TIMER (SPI ACTIVITY) CHARTA REFOUT VREF +V SENSE_A VOUT RANGE V REFERENCE OUT_A REFIN DAC CHANNEL A SCALING BUFFERS I , I , I OUT_B OUT_C OUT_D R , R , R DAC CHANNEL B SET_B SET_C SET_D AD1 CHARTB, CHARTC, CHARTD DAC CHANNEL C AD5755-1 +V , +V , +V SENSE_B SENSE_C SENSE_D DAC CHANNEL D AD0 V , V , V OUT_B OUT_C OUT_D V , V , V SW , SW , SW BOOST_B BOOST_C BOOST_D B C D Figure 2. Rev. C | Page 4 of 52 09226-001 Data Sheet AD5755-1 SPECIFICATIONS AVDD = VBOOST_x = 15 V; AVSS = −15 V/0 V; DVDD = 2.7 V to 5.5 V; AVCC = 4.5 V to 5.5 V; dc-to-dc converter disabled; AGND = DGND = GNDSWx = 0 V; REFIN = 5 V; voltage outputs: RL = 1 kΩ, CL = 220 pF; current outputs: RL = 300 Ω; all specifications TMIN to TMAX, unless otherwise noted. Table 1. 1 Parameter Min Typ Max Unit Test Conditions/Comments VOLTAGE OUTPUT Output Voltage Ranges 0 5 V 0 10 V −5 +5 V −10 +10 V 0 6 V 0 12 V −6 +6 V −12 +12 V ACCURACY BIPOLAR SUPPLY AVSS = −15 V, loaded and unloaded Resolution 16 Bits Total Unadjusted Error (TUE) −0.04 +0.04 % FSR −0.03 ±0.0032 +0.03 % FSR T = 25°C A TUE Long-Term Stability 35 ppm FSR Drift after 1000 hours, TJ = 150°C Relative Accuracy (INL) −0.006 ±0.0012 +0.006 % FSR 0 V to 5 V, 0 V to 10 V, ±5 V, ±10 V ranges −0.008 ±0.0012 +0.008 % FSR On overranges Differential Nonlinearity (DNL) −1 +1 LSB Guaranteed monotonic Zero-Scale Error −0.03 ±0.002 +0.03 % FSR 2 Zero-Scale TC ±2 ppm FSR/°C Bipolar Zero Error −0.03 ±0.002 +0.03 % FSR 2 Bipolar Zero TC ±1 ppm FSR/°C Offset Error −0.03 ±0.002 +0.03 % FSR 2 Offset TC ±2 ppm FSR/°C Gain Error −0.03 ±0.004 +0.03 % FSR 2 Gain TC ±3 ppm FSR/°C Full-Scale Error −0.03 ±0.002 +0.03 % FSR 2 Full-Scale TC ±2 ppm FSR/°C 2 ACCURACY UNIPOLAR SUPPLY AV = 0 V SS Total Unadjusted Error (TUE) −0.06 ±0.025 +0.06 % FSR 3 Relative Accuracy (INL) −0.009 +0.009 % FSR Differential Nonlinearity (DNL) −1 +1 LSB Guaranteed monotonic Zero-Scale Error +0.22 % FSR Offset Error −0.07 ±0.025 +0.07 % FSR Gain Error −0.07 ±0.015 +0.07 % FSR Full-Scale Error −0.06 ±0.015 +0.06 % FSR 2 OUTPUT CHARACTERISTICS Headroom 1 2.2 V With respect to VBOOST supply Footroom 0.7 1.4 V With respect to the AVSS supply, bipolar output ranges Output Voltage Drift vs. Time 20 ppm FSR Drift after 1000 hours, ¾ scale output, T = 150°C, J AVSS = −15 V Short-Circuit Current 12/6 16/8 mA Programmable by user, defaults to 16 mA typical level Load 1 kΩ For specified performance Capacitive Load Stability 10 nF 2 µF External compensation capacitor of 220 pF connected DC Output Impedance 0.06 Ω DC PSRR 50 µV/V DC Crosstalk 24 µV Rev. C | Page 5 of 52 AD5755-1 Data Sheet 1 Parameter Min Typ Max Unit Test Conditions/Comments CURRENT OUTPUT Output Current Ranges 0 24 mA 0 20 mA 4 20 mA Resolution 16 Bits ACCURACY (EXTERNAL R ) SET Assumes ideal resistor, see the External Current Setting Resistor section for more information Total Unadjusted Error (TUE) −0.05 ±0.009 +0.05 % FSR TUE Long-Term Stability 100 ppm FSR Drift after 1000 hours, T = 150°C J Relative Accuracy (INL) −0.006 +0.006 % FSR Differential Nonlinearity (DNL) −1 +1 LSB Guaranteed monotonic Offset Error −0.05 ±0.005 +0.05 % FSR 2 Offset Error Drift ±4 ppm FSR/°C Gain Error −0.05 ±0.004 +0.05 % FSR 2 Gain TC ±3 ppm FSR/°C Full-Scale Error −0.05 ±0.008 +0.05 % FSR 2 Full-Scale TC ±5 ppm FSR/°C DC Crosstalk 0.0005 % FSR External RSET ACCURACY (INTERNAL RSET) 4, 5 Total Unadjusted Error (TUE) −0.14 +0.14 % FSR −0.11 ±0.009 +0.11 % FSR TA = 25°C TUE Long-Term Stability 180 ppm FSR Drift after 1000 hours, TJ = 150°C Relative Accuracy (INL) −0.006 +0.006 % FSR Relative Accuracy (INL) −0.004 +0.004 % FSR TA = 25°C Differential Nonlinearity (DNL) −1 +1 LSB Guaranteed monotonic 4, 5 Offset Error −0.05 +0.05 % FSR −0.04 ±0.007 +0.04 % FSR TA = 25°C 2 Offset Error Drift ±6 ppm FSR/°C Gain Error −0.12 +0.12 % FSR −0.06 ±0.002 +0.06 % FSR TA = 25°C 2 Gain TC ±9 ppm FSR/°C 4, 5 Full-Scale Error −0.14 +0.14 % FSR −0.1 ±0.007 +0.1 % FSR T = 25°C A 2 Full-Scale TC ±14 ppm FSR/°C 5 DC Crosstalk −0.011 % FSR Internal RSET 2 OUTPUT CHARACTERISTICS Current Loop Compliance Voltage V − V − V BOOST_x BOOST_x 2.4 2.7 Output Current Drift vs. Time Drift after 1000 hours, ¾ scale output, T = 150°C J 90 ppm FSR External R SET 140 ppm FSR Internal RSET Resistive Load 1000 Ω The dc-to-dc converter has been characterized with a maximum load of 1 kΩ, chosen such that compli- ance is not exceeded; see Figure 53 and DC-DC MaxV bits in Table 25 Output Impedance 100 MΩ DC PSRR 0.02 1 µA/V Rev. C | Page 6 of 52 Data Sheet AD5755-1 1 Parameter Min Typ Max Unit Test Conditions/Comments REFERENCE INPUT/OUTPUT 2 Reference Input Reference Input Voltage 4.95 5 5.05 V For specified performance DC Input Impedance 45 150 MΩ Reference Output Output Voltage 4.995 5 5.005 V TA = 25°C 2 Reference TC −10 ±5 +10 ppm/°C 2 Output Noise (0.1 Hz to 10 Hz) 7 µV p-p 2 Noise Spectral Density 100 nV/√Hz At 10 kHz 2 Output Voltage Drift vs. Time 180 ppm Drift after 1000 hours, T = 150°C J 2 Capacitive Load 1000 nF Load Current 9 mA See Figure 64 Short-Circuit Current 10 mA 2 Line Regulation 3 ppm/V See Figure 65 2 Load Regulation 95 ppm/mA See Figure 64 2 Thermal Hysteresis 160 ppm First temperature cycle 5 ppm Second temperature cycle DC-TO-DC Switch Switch On Resistance 0.425 Ω Switch Leakage Current 10 nA Peak Current Limit 0.8 A Oscillator Oscillator Frequency 11.5 13 14.5 MHz This oscillator is divided down to give the dc-to-dc converter switching frequency Maximum Duty Cycle 89.6 % At 410 kHz dc-to-dc switching frequency 2 DIGITAL INPUTS JEDEC compliant VIH, Input High Voltage 2 V V , Input Low Voltage 0.8 V IL Input Current −1 +1 µA Per pin Pin Capacitance 2.6 pF Per pin 2 DIGITAL OUTPUTS SDO, ALERT V , Output Low Voltage 0.4 V Sinking 200 µA OL VOH, Output High Voltage DVDD − 0.5 V Sourcing 200 µA High Impedance Leakage −1 +1 µA Current High Impedance Output 2.5 pF Capacitance FAULT V , Output Low Voltage 0.4 V 10 kΩ pull-up resistor to DV OL DD VOL, Output Low Voltage 0.6 V At 2.5 mA VOH, Output High Voltage 3.6 V 10 kΩ pull-up resistor to DVDD POWER REQUIREMENTS AV 9 33 V DD AVSS −26.4 −10.8/0 V DV 2.7 5.5 V DD AV 4.5 5.5 V CC Rev. C | Page 7 of 52 AD5755-1 Data Sheet 1 Parameter Min Typ Max Unit Test Conditions/Comments AIDD 8.6 10.5 mA Voltage output mode on all channels, output unloaded, over supplies 7 7.5 mA Current output mode on all channels AI −11 −8.8 mA Voltage output mode on all channels, output SS unloaded, over supplies −1.7 mA Current output mode on all channels DI 9.2 11 mA V = DV , V = DGND, internal oscillator running, CC IH DD IL over supplies AI 1 mA Output unloaded, over supplies CC I 2.7 mA Per channel, voltage output mode, output BOOST unloaded, over supplies 6 I 1 mA Per channel, current output mode, 0 mA output BOOST Power Dissipation 173 mW AVDD = +15 V, AVSS = −15 V, dc-to-dc converter enable, current output mode, outputs disabled 1 Temperature range: −40°C to +105°C; typical at +25°C. 2 Guaranteed by design and characterization; not production tested. 3 For voltage output ranges in unipolar supply mode, the INL and TUE are measured beginning from Code 4096. 4 For current outputs with internal RSET, the offset, full-scale, and TUE measurements exclude dc crosstalk. The measurements are made with all four channels enabled loaded with the same code. 5 See the Current Output Mode with Internal RSET section for more explanation of the dc crosstalk. 6 Efficiency plots in Figure 55, Figure 56, Figure 57, and Figure 58 include the I quiescent current BOOST AC PERFORMANCE CHARACTERISTICS AVDD = VBOOST_x = 15 V; AVSS = −15 V; DVDD = 2.7 V to 5.5 V; AVCC = 4.5 V to 5.5 V; dc-to-dc converter disabled; AGND = DGND = GNDSWx = 0 V; REFIN = 5 V; voltage outputs: RL = 2 kΩ, CL = 220 pF; current outputs: RL = 300 Ω; all specifications TMIN to TMAX, unless otherwise noted. Table 2. 1 Parameter Min Typ Max Unit Test Conditions/Comments DYNAMIC PERFORMANCE Voltage Output Output Voltage Settling Time 11 µs 5 V step to ±0.03% FSR, 0 V to 5 V range 18 µs 10 V step to ±0.03% FSR, 0 V to 10 V range 13 µs 100 mV step to 1 LSB (16-bit LSB), 0 V to 10 V range Slew Rate 1.9 V/µs 0 V to 10 V range Power-On Glitch Energy 150 nV-sec Digital-to-Analog Glitch Energy 6 nV-sec Glitch Impulse Peak Amplitude 25 mV Digital Feedthrough 1 nV-sec DAC to DAC Crosstalk 2 nV-sec 0 V to 10 V range Output Noise (0.1 Hz to 10 Hz 0.15 LSB p-p 16-bit LSB, 0 V to 10 V range Bandwidth) Output Noise Spectral Density 150 nV/√Hz Measured at 10 kHz, midscale output, 0 V to 10 V range AC PSRR 83 dB 200 mV 50 Hz/60 Hz sine wave superimposed on power supply voltage Current Output Output Current Settling Time 15 µs To 0.1% FSR (0 mA to 24 mA) See test conditions/ ms See Figure 49, Figure 50, and Figure 51 comments Output Noise (0.1 Hz to 10 Hz 0.15 LSB p-p 16-bit LSB, 0 mA to 24 mA range Bandwidth) Output Noise Spectral Density 0.5 nA/√Hz Measured at 10 kHz, midscale output, 0 mA to 24 mA range 1 Guaranteed by design and characterization; not production tested. Rev. C | Page 8 of 52 Data Sheet AD5755-1 TIMING CHARACTERISTICS AVDD = VBOOST_x = 15 V; AVSS = −15 V; DVDD = 2.7 V to 5.5 V; AVCC = 4.5 V to 5.5 V; dc-to-dc converter disabled; AGND = DGND = GNDSWx = 0 V; REFIN = 5 V; voltage outputs: RL = 1 kΩ, CL = 220 pF; current outputs: RL = 300 Ω; all specifications TMIN to TMAX, unless otherwise noted. Table 3. 1, 2, 3 Parameter Limit at T , T Unit Description MIN MAX t1 33 ns min SCLK cycle time t2 13 ns min SCLK high time t 13 ns min SCLK low time 3 t 13 ns min SYNC falling edge to SCLK falling edge setup time 4 th nd t5 13 ns min 24 /32 SCLK falling edge to SYNC rising edge (see Figure 78) t6 198 ns min SYNC high time t7 5 ns min Data setup time t 5 ns min Data hold time 8 t 20 µs min SYNC rising edge to LDAC falling edge (all DACs updated or any channel has 9 digital slew rate control enabled) 5 µs min SYNC rising edge to LDAC falling edge (single DAC updated) t10 10 ns min LDAC pulse width low t11 500 ns max LDAC falling edge to DAC output response time t See the AC Performance µs max DAC output settling time 12 Characteristics section t 10 ns min CLEAR high time 13 t14 5 µs max CLEAR activation time t15 40 ns max SCLK rising edge to SDO valid t16 21 µs min SYNC rising edge to DAC output response time (LDAC = 0) (all DACs updated) 5 µs min SYNC rising edge to DAC output response time (LDAC = 0) (single DAC updated) t 500 ns min LDAC falling edge to SYNC rising edge 17 t18 800 ns min RESET pulse width 4 t19 20 µs min SYNC high to next SYNC low (digital slew rate control enabled) (all DACs updated) 5 µs min SYNC high to next SYNC low (digital slew rate control disabled) (single DAC updated) 1 Guaranteed by design and characterization; not production tested. 2 All input signals are specified with t = t = 5 ns (10% to 90% of DV ) and timed from a voltage level of 1.2 V. R F DD 3 See Figure 3, Figure 4, Figure 5, and Figure 6. 4 This specification applies if LDAC is held low during the write cycle; otherwise, see t9. Rev. C | Page 9 of 52 AD5755-1 Data Sheet Timing Diagrams t 1 SCLK 1 2 24 t t t 6 3 2 t t 4 5 SYNC t 8 t 19 t 7 SDIN MSB LSB t t 10 10 t 9 LDAC t t 17 12 t 11 V OUT_x LDAC = 0 t 12 t 16 V OUT_x t 13 CLEAR t 14 V OUT_x t 18 RESET Figure 3. Serial Interface Timing Diagram SCLK 1 24 1 24 t 6 SYNC MSB LSB MSB LSB SDIN INPUT WORD SPECIFIES NOP CONDITION REGISTER TO BE READ MSB LSB SDO UNDEFINED SELECTED REGISTER DATA CLOCKED OUT t 15 Figure 4. Readback Timing Diagram Rev. C | Page 10 of 52 09226-002 09226-003 Data Sheet AD5755-1 LSB MSB 1 2 16 SCLK SYNC DUT_ DUT_ R/W X X X D15 D14 D1 D0 SDIN AD1 AD0 SDO_ STATUS STATUS STATUS STATUS SDO SDO DISABLED ENAB Figure 5. Status Readback During Write 200µA I OL V (MIN) OR TO OUTPUT OH PIN V (MAX) OL C L 50pF 200µA I OH Figure 6. Load Circuit for SDO Timing Diagram Rev. C | Page 11 of 52 09226-005 09226-004 AD5755-1 Data Sheet ABSOLUTE MAXIMUM RATINGS TA = 25°C, unless otherwise noted. Transient currents of up to Stresses above those listed under Absolute Maximum Ratings 100 mA do not cause SCR latch-up. may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any Table 4. other conditions above those indicated in the operational Parameter Rating section of this specification is not implied. Exposure to absolute AV , V to AGND, DGND −0.3 V to +33 V DD BOOST_x maximum rating conditions for extended periods may affect AVSS to AGND, DGND +0.3 V to −28 V device reliability. AVDD to AVSS −0.3 V to +60 V ESD CAUTION AV to AGND −0.3 V to +7 V CC DVDD to DGND −0.3 V to +7 V Digital Inputs to DGND −0.3 V to DV + 0.3 V or +7 V DD (whichever is less) Digital Outputs to DGND −0.3 V to DVDD + 0.3 V or +7 V (whichever is less) REFIN, REFOUT to AGND −0.3 V to AVDD + 0.3 V or +7 V (whichever is less) V to AGND AV to V or 33 V if using OUT_x SS BOOST_x the dc-to-dc circuitry +V to AGND AV to V or 33 V if using SENSE_x SS BOOST_x the dc-to-dc circuitry IOUT_x to AGND AVSS to VBOOST_x or 33 V if using the dc-to-dc circuitry SWx to AGND −0.3 to +33 V AGND, GNDSW to DGND −0.3 V to +0.3 V x Operating Temperature Range (TA) 1 Industrial −40°C to +105°C Storage Temperature Range −65°C to +150°C Junction Temperature (TJ max) 125°C 64-Lead LFCSP 2 θ Thermal Impedance 20°C/W JA Power Dissipation (TJ max − TA)/θJA Lead Temperature JEDEC industry standard Soldering J-STD-020 1 Power dissipated on chip must be derated to keep the junction temperature below 125°C. 2 Based on a JEDEC 4-layer test board. Rev. C | Page 12 of 52 Data Sheet AD5755-1 PIN CONFIGURATION AND FUNCTION DESCRIPTIONS PIN 1 INDICATOR R 1 48 COMP SET_B DCDC_C R 2 47 I SET_A OUT_C REFGND 3 46 V BOOST_C REFGND 4 45 AV CC AD0 5 44 SW C AD1 6 43 GNDSW C SYNC 7 42 GNDSW AD5755-1 D SCLK 8 41 SW D TOP VIEW SDIN 9 40 AV SS (Not to Scale) SDO 10 39 SW A DV 11 38 DD GNDSW A DGND 12 37 GNDSW B LDAC 13 36 SW B CLEAR 14 35 AGND ALERT 15 34 V BOOST_B FAULT 16 33 I OUT_B NOTES 1. THE EXPOSED PAD SHOULD BE CONNECTED TO THE POTENTIAL OF THE AV PIN, OR, ALTERNATIVELY, IT CAN BE LEFT ELECTRICALLY SS UNCONNECTED. IT IS RECOMMENDED THAT THE PAD BE THERMALLY CONNECTED TO A COPPER PLANE FOR ENHANCED THERMAL PERFORMANCE. Figure 7. Pin Configuration Table 5. Pin Function Descriptions Pin No. Mnemonic Description 1 RSET_B An external, precision, low drift 15 kΩ current setting resistor can be connected to this pin to improve the IOUT_B temperature drift performance. See the Device Features section. 2 R An external, precision, low drift 15 kΩ current setting resistor can be connected to this pin to improve the I SET_A OUT_A temperature drift performance. See the Device Features section. 3, 4 REFGND Ground Reference Point for Internal Reference. 5 AD0 Address Decode for the Device Under Test (DUT) on the Board. 6 AD1 Address Decode for the DUT on the Board. 7 SYNC Active Low Input. This is the frame synchronization signal for the serial interface. While SYNC is low, data is transferred in on the falling edge of SCLK. 8 SCLK Serial Clock Input. Data is clocked into the input shift register on the falling edge of SCLK. This operates at clock speeds of up to 30 MHz. 9 SDIN Serial Data Input. Data must be valid on the falling edge of SCLK. 10 SDO Serial Data Output. Used to clock data from the serial register in readback mode. See Figure 4 and Figure 5. 11 DV Digital Supply. The voltage range is from 2.7 V to 5.5 V. DD 12 DGND Digital Ground. 13 LDAC Load DAC, Active Low Input. This is used to update the DAC register and consequently the DAC outputs. When tied permanently low, the addressed DAC data register is updated on the rising edge of SYNC. If LDAC is held high during the write cycle, the DAC input register is updated, but the DAC output update only takes place at the falling edge of LDAC (see Figure 3). Using this mode, all analog outputs can be updated simultaneously. The LDAC pin must not be left unconnected. 14 CLEAR Active High, Edge Sensitive Input. Asserting this pin sets the output current and voltage to the preprogrammed clear code bit setting. Only channels enabled to be cleared are cleared. See the Device Features section for more information. When CLEAR is active, the DAC output register cannot be written to. Rev. C | Page 13 of 52 POC 17 64 R SET_C RESET 18 63 R SET_D AV 19 62 DD REFOUT COMP 20 61 LV_A REFIN 21 60 COMP CHARTA LV_D +V 22 59 CHARTD SENSE_A COMP 23 58 +V DCDC_A SENSE_D V 24 57 COMP BOOST_A DCDC_D V 25 56 V OUT_A BOOST_D I 26 55 V OUT_A OUT_D AV 27 54 I OUT_D SS COMP 28 53 AV LV_B SS 29 52 COMP CHARTB LV_C +V 30 51 CHARTC SENSE_B V 31 50 +V OUT_B SENSE_C COMP 32 49 V DCDC_B OUT_C 09266-006 AD5755-1 Data Sheet Pin No. Mnemonic Description 15 ALERT Active High Output. This pin is asserted when there has been no SPI activity on the interface pins for a predetermined time. See the Device Features section for more information. 16 FAULT Active Low Output. This pin is asserted low when an open circuit in current mode is detected, a short circuit in voltage mode is detected, a PEC error is detected, or an overtemperature is detected (see the Device Features section). Open-drain output. 17 POC Power-On Condition. This pin determines the power-on condition and is read during power-on or, alternatively, after a device reset. If POC = 0, the device is powered up with the voltage and current channels in tristate mode. If POC = 1, the device is powered up with a 30 kΩ pull-down resistor to ground on the voltage output channel, and the current channel is in tristate mode. 18 RESET Hardware Reset, Active Low Input. 19 AV Positive Analog Supply. The voltage range is from 9 V to 33 V. DD 20 COMPLV_A Optional Compensation Capacitor Connection for VOUT_A Output Buffer. Connecting a 220 pF capacitor between this pin and the VOUT_A pin allows the voltage output to drive up to 2 µF. Note that the addition of this capacitor reduces the bandwidth of the output amplifier, increasing the settling time. 21 CHARTA HART Input Connection for DAC Channel A. 22 +V Sense Connection for the Positive Voltage Output Load Connection for V . SENSE_A OUT_A 23 COMPDCDC_A DC-to-DC Compensation Capacitor. Connect a 10 nF capacitor from this pin to ground. Used to regulate the feedback loop of the Channel A dc-to-dc converter. Alternatively, if using an external compensation resistor, place a resistor in series with a capacitor to ground from this pin (see the DC-to-DC Converter Compensation Capacitors and the AICC Supply Requirements—Slewing sections in the Device Features section for more information). 24 V Supply for Channel A Current Output Stage (see Figure 73). This is also the supply for the V stage, which is BOOST_A OUT_x regulated to 15 V by the dc-to-dc converter. To use the dc-to-dc feature of the device, connect as shown in Figure 80. 25 VOUT_A Buffered Analog Output Voltage for DAC Channel A. 26 I Current Output Pin for DAC Channel A. OUT_A 27 AV Negative Analog Supply. Voltage range is from −10.8 V to −26.4 V. SS 28 COMP Optional Compensation Capacitor Connection for V Output Buffer. Connecting a 220 pF capacitor between LV_B OUT_B this pin and the VOUT_B pin allows the voltage output to drive up to 2 µF. Note that the addition of this capacitor reduces the bandwidth of the output amplifier, increasing the settling time. 29 CHARTB HART Input Connection for DAC Channel B. 30 +V Sense Connection for the Positive Voltage Output Load Connection for V . SENSE_B OUT_B 31 V Buffered Analog Output Voltage for DAC Channel B. OUT_B 32 COMPDCDC_B DC-to-DC Compensation Capacitor. Connect a 10 nF capacitor from this pin to ground. Used to regulate the feedback loop of the Channel B dc-to-dc converter. Alternatively, if using an external compensation resistor, place a resistor in series with a capacitor to ground from this pin (see the DC-to-DC Converter Compensation Capacitors and AI Supply Requirements—Slewing sections in the Device Features section for more CC information). 33 I Current Output Pin for DAC Channel B. OUT_B 34 VBOOST_B Supply for Channel B Current Output Stage (see Figure 73). This is also the supply for the VOUT_x stage, which is regulated to 15 V by the dc-to-dc converter. To use the dc-to-dc feature of the device, connect as shown in Figure 80. 35 AGND Ground Reference Point for Analog Circuitry. This must be connected to 0 V. 36 SW Switching Output for Channel B DC-to-DC Circuitry. To use the dc-to-dc feature of the device, connect as shown B in Figure 80. 37 GNDSWB Ground Connection for DC-to-DC Switching Circuit. This pin should always be connected to ground. 38 GNDSWA Ground Connection for DC-to-DC Switching Circuit. This pin should always be connected to ground. 39 SW Switching Output for Channel A DC-to-DC Circuitry. To use the dc-to-dc feature of the device, connect as shown A in Figure 80. 40 AV Negative Analog Supply Pin. The voltage range is from −10.8 V to −26.4 V. This pin can be connected to 0 V if SS using the device in unipolar supply mode. 41 SWD Switching Output for Channel D DC-DC Circuitry. To use the dc-to-dc feature of the device, connect as shown in Figure 80. 42 GNDSW Ground Connections for DC-to-DC Switching Circuit. This pin should always be connected to ground. D 43 GNDSW Ground Connections for DC-to-DC Switching Circuit. This pin should always be connected to ground. C 44 SW Switching Output for Channel C DC-to-DC Circuitry. To use the dc-to-dc feature of the device, connect as shown C in Figure 80. 45 AVCC Supply for DC-to-DC Circuitry. Rev. C | Page 14 of 52 Data Sheet AD5755-1 Pin No. Mnemonic Description 46 VBOOST_C Supply for Channel C Current Output Stage (see Figure 73). This is also the supply for the VOUT_x stage, which is regulated to 15 V by the dc-to-dc converter. To use the dc-to-dc feature of the device, connect as shown in Figure 80. 47 I Current Output Pin for DAC Channel C. OUT_C 48 COMP DC-to-DC Compensation Capacitor. Connect a 10 nF capacitor from this pin to ground. Used to regulate the DCDC_C feedback loop of the Channel C dc-to-dc converter. Alternatively, if using an external compensation resistor, place a resistor in series with a capacitor to ground from this pin (see the DC-to-DC Converter Compensation Capacitors and AICC Supply Requirements—Slewing sections in the Device Features section for more information). 49 V Buffered Analog Output Voltage for DAC Channel C. OUT_C 50 +V Sense Connection for the Positive Voltage Output Load Connection for V . SENSE_C OUT_C 51 CHARTC HART Input Connection for DAC Channel C. 52 COMPLV_C Optional Compensation Capacitor Connection for VOUT_C Output Buffer. Connecting a 220 pF capacitor between this pin and the VOUT_C pin allows the voltage output to drive up to 2 µF. Note that the addition of this capacitor reduces the bandwidth of the output amplifier, increasing the settling time. 53 AV Negative Analog Supply Pin. SS 54 I Current Output Pin for DAC Channel D. OUT_D 55 VOUT_D Buffered Analog Output Voltage for DAC Channel D. 56 VBOOST_D Supply for Channel D Current Output Stage (see Figure 73). This is also the supply for the VOUT_x stage, which is regulated to 15 V by the dc-to-dc converter. To use the dc-to-dc feature of the device, connect as shown in Figure 80. 57 COMP DC-to-DC Compensation Capacitor. Connect a 10 nF capacitor from this pin to ground. Used to regulate the DCDC_D feedback loop of the Channel D dc-to-dc converter. Alternatively, if using an external compensation resistor, place a resistor in series with a capacitor to ground from this pin (see the DC-to-DC Converter Compensation Capacitors and AICC Supply Requirements—Slewing sections in the Device Features section for more information). 58 +V Sense Connection for the Positive Voltage Output Load Connection for V . SENSE_D OUT_D 59 CHARTD HART Input Connection for DAC Channel D 60 COMPLV_D Optional Compensation Capacitor Connection for VOUT_D Output Buffer. Connecting a 220 pF capacitor between this pin and the VOUT_D pin allows the voltage output to drive up to 2 µF. Note that the addition of this capacitor reduces the bandwidth of the output amplifier, increasing the settling time. 61 REFIN External Reference Voltage Input. 62 REFOUT Internal Reference Voltage Output. It is recommended to place a 0.1 µF capacitor between REFOUT and REFGND. REFOUT must be connected to REFIN to use the internal reference. 63 RSET_D An external, precision, low drift 15 kΩ current setting resistor can be connected to this pin to improve the IOUT_D temperature drift performance. See the Device Features section. 64 R An external, precision, low drift 15 kΩ current setting resistor can be connected to this pin to improve the I SET_C OUT_C temperature drift performance. See the Device Features section. EPAD Exposed Pad. This exposed pad should be connected to the potential of the AVSS pin, or, alternatively, it can be left electrically unconnected. It is recommended that the pad be thermally connected to a copper plane for enhanced thermal performance. Rev. C | Page 15 of 52 AD5755-1 Data Sheet TYPICAL PERFORMANCE CHARACTERISTICS VOLTAGE OUTPUTS 0.0015 0.0015 ±10V RANGE AV = +15V DD ±5V RANGE AV = –15V SS +10V RANGE T = 25°C A 0.0010 +5V RANGE 0.0010 +10V RANGE WITH DCDC 0.0005 +5V RANGE MAX INL +10V RANGE MAX INL ±5V RANGE MAX INL ±10V RANGE MAX INL 0.0005 +5V RANGE MIN INL +10V RANGE MIN INL ±5V RANGE MIN INL ±10V RANGE MIN INL 0 AV = +15V DD 0 AV = –15V SS –0.0005 OUTPUT UNLOADED –0.0005 –0.0010 –0.0015 –0.0010 –40 –20 0 20 40 60 80 100 0 10k 20k 30k 40k 50k 60k TEMPERATURE (°C) CODE Figure 8. Integral Nonlinearity Error vs. DAC Code Figure 11. Integral Nonlinearity Error vs. Temperature 1.0 1.0 ±10V RANGE AV = +15V DD AV = +15V 0.8 0.8 DD ±5V RANGE AV = –15V SS AV = –15V +10V RANGE SS T = 25°C A +5V RANGE 0.6 0.6 ALL RANGES +10V RANGE WITH DCDC 0.4 0.4 0.2 0.2 DNL ERROR MAX 0 0 DNL ERROR MIN –0.2 –0.2 –0.4 –0.4 –0.6 –0.6 –0.8 –0.8 –1.0 –1.0 0 10k 20k 30k 40k 50k 60k –40 –20 0 20 40 60 80 100 CODE TEMPERATURE (°C) Figure 9. Differential Nonlinearity Error vs. DAC Code Figure 12. Differential Nonlinearity Error vs. Temperature 0.006 0.012 ±10V RANGE AV = +15V DD +5V RANGE ±5V RANGE AV = –15V SS +10V RANGE 0.010 0.004 +10V RANGE T = 25°C ±5V RANGE A +5V RANGE ±10V RANGE +10V RANGE WITH DCDC 0.008 0.002 AV = +15V DD 0.006 AV = –15V SS 0 OUTPUT UNLOADED 0.004 –0.002 0.002 –0.004 0 –0.006 –0.002 –0.008 –0.004 –0.010 –0.006 0 10k 20k 30k 40k 50k 60k –40 –20 0 20 40 60 80 100 CODE TEMPERATURE (°C) Figure 10. Total Unadjusted Error vs. DAC Code Figure 13. Total Unadjusted Error vs. Temperature Rev. C | Page 16 of 52 TOTAL UNADJUSTED ERROR (%FSR) INL ERROR (%FSR) DNL ERROR (LSB) 09226-024 09226-023 09226-025 INL ERROR (%FSR) TOTAL UNADJUSTED ERROR (%FSR) DNL ERROR (LSB) 09226-128 09226-129 09226-127 Data Sheet AD5755-1 0 0.0025 0.0020 –0.005 0.0015 –0.010 0.0010 +5V RANGE –0.015 0.0005 +12V RANGE AV = +15V DD 0 –0.020 AV = 0V SS ±5V RANGE OUTPUT UNLOADED –0.0005 ±10V RANGE –0.025 AV = +15V DD –0.0010 AV = –15V SS OUTPUT UNLOADED –0.030 –0.0015 –0.035 –0.0020 –40 –20 0 20 40 60 80 100 –40 –20 0 20 40 60 80 100 TEMPERATURE (°C) TEMPERATURE (°C) Figure 14. Total Unadjusted Error vs. Temperature, Single Supply Figure 17. Bipolar Zero Error vs. Temperature 0.012 0.010 +5V RANGE +5V RANGE +10V RANGE 0.010 0.008 +10V RANGE ±5V RANGE ±5V RANGE ±10V RANGE ±10V RANGE 0.008 0.006 AV = +15V AV = +15V DD DD AV = –15V 0.006 AV = –15V SS SS 0.004 OUTPUT UNLOADED OUTPUT UNLOADED 0.004 0.002 0.002 0 0 –0.002 –0.002 –0.004 –0.004 –0.006 –0.006 –40 –20 0 20 40 60 80 100 –40 –20 0 20 40 60 80 100 TEMPERATURE (°C) TEMPERATURE (°C) Figure 15. Full-Scale Error vs. Temperature Figure 18. Gain Error vs. Temperature 0.0015 0.0015 0.0010 0.0010 0.0005 0.0005 0 0 –0.0005 –0.0005 +5V RANGE –0.0010 +5V RANGE +10V RANGE +10V RANGE –0.0010 AV = +15V ±5V RANGE DD –0.0015 ±10V RANGE AV = –15V SS AV = +15V OUTPUT UNLOADED DD –0.0015 –0.0020 AV = –15V SS OUTPUT UNLOADED –0.0020 –0.0025 –40 –20 0 20 40 60 80 100 –40 –20 0 20 40 60 80 100 TEMPERATURE (°C) TEMPERATURE (°C) Figure 16. Offset Error vs. Temperature Figure 19. Zero-Scale Error vs. Temperature Rev. C | Page 17 of 52 OFFSET (%FSR) FULL-SCALE ERROR (%FSR) TOTAL UNADJUSTED ERROR (%FSR) 09226-132 09226-130 09226-133 BIPOLAR ZERO ERROR (%FSR) ZERO-SCALE ERROR (%FSR) GAIN ERROR (%FSR) 09226-135 09226-136 09226-134 AD5755-1 Data Sheet 0.0020 0.0020 8mA LIMIT, CODE = 0xFFFF 0.0015 0.0015 16mA LIMIT, CODE = 0xFFFF 0.0010 0.0010 0.0005 0.0005 0V TO 10V RANGE MAX INL 0V TO 10V RANGE MIN INL 0 0 T = 25°C A AV = –26.4V FOR AV > +26.4V SS DD –0.0005 –0.0005 –0.0010 –0.0010 AV = +15V DD AV = –15V SS ±10V RANGE –0.0015 –0.0015 T = 25°C A –0.0020 –0.0020 10 15 20 25 30 –20 –16 –12 –8 –4 0 4 8 12 16 20 SUPPLY (V) OUTPUT CURRENT (mA) Figure 20. Integral Nonlinearity Error vs. AV /|AV | Figure 23. Source and Sink Capability of Output Amplifier DD SS 1.0 12 AV = +15V DD AV = +15V DD 0.8 AV = –15V SS AV = –15V SS ALL RANGES 8 ±10V RANGE 0.6 T = 25°C A T = 25°C A AV = –26.4V FOR AV > +26.4V SS DD OUTPUT UNLOADED 0.4 4 0.2 DNL ERROR MAX 0 0 DNL ERROR MIN –0.2 –4 –0.4 –0.6 –8 –0.8 –12 –1.0 10 15 20 25 30 –5 0 5 10 15 TIME (µs) SUPPLY (V) Figure 21. Differential Nonlinearity Error vs. AV /|AV | Figure 24. Full-Scale Positive Step DD SS 0.008 12 0V TO 10V RANGE MAX TUE AV = +15V DD 0V TO 10V RANGE MIN TUE AV = –15V SS T = 25°C 0.006 A 8 ±10V RANGE AV = –26.4V FOR AV > +26.4V SS DD T = 25°C A OUTPUT UNLOADED 0.004 4 0 0.002 –4 0 –8 –0.008 –12 –0.004 10 15 20 25 30 –5 0 5 10 15 TIME (µs) SUPPLY (V) Figure 22. Total Unadjusted Error vs. AVDD/|AVSS| Figure 25. Full-Scale Negative Step Rev. C | Page 18 of 52 TOTAL UNADJUSTED ERROR (%FSR) INL EROR (%FSR) DNL ERROR (LSB) 09226-138 09226-034 09226-035 OUTPUT VOLTAGE DELTA (V) OUTPUT VOLTAGE (V) OUTPUT VOLTAGE (V) 09226-038 09226-037 09226-036 Data Sheet AD5755-1 15 25 0x7FFF TO 0x8000 20 0x8000 TO 0x7FFF 10 AV = +15V DD 15 AV = –15V SS +10V RANGE 5 10 T = 25ºC A 5 0 0 –5 –5 –10 –10 –15 AV = +15V DD –15 AV = –15V SS –20 T = 25°C A –25 –20 0 25 50 75 100 125 0 1 2 3 4 5 TIME (µs) TIME (µs) Figure 29. VOUT_x vs. Time on Power-Up Figure 26. Digital-to-Analog Glitch 15 60 AV = +15V DD AV = –15V SS 40 ±10V RANGE 10 T = 25°C A 20 OUTPUT UNLOADED 0 5 –20 0 –40 –60 POC = 1 –5 POC = 0 –80 AV = +15V DD AV = –15V SS –100 –10 ±10V RANGE T = 25°C A –120 INT_ENABLE = 1 –15 –140 0 1 2 3 4 5 6 7 8 9 10 0 2 4 6 8 10 TIME (s) TIME (µs) Figure 27. Peak-to-Peak Noise (0.1 Hz to 10 Hz Bandwidth) Figure 30. VOUT_x vs. Time on Output Enable 300 0 AV = +15V ±10V RANGE OUTPUT UNLOADED DD AV = +15V AV = –15V T = 25°C DD SS A V = +15V BOOST 200 –20 AV = –15V SS T = 25°C A 100 –40 0 –60 –100 –80 –200 –100 –300 –120 10 100 1k 10k 100k 1M 10M 0 1 2 3 4 5 6 7 8 9 10 TIME (µs) FREQUENCY (Hz) Figure 28. Peak-to-Peak Noise (100 kHz Bandwidth) Figure 31. VOUT_x PSRR vs. Frequency Rev. C | Page 19 of 52 OUTPUT VOLTAGE (µV) OUTPUT VOLTAGE (mV) OUTPUT VOLTAGE (µV) 09226-040 09226-041 09226-039 V PSRR (dB) OUT_x OUTPUT VOLTAGE (mV) OUTPUT VOLTAGE (mV) 09226-044 09226-043 09226-045 AD5755-1 Data Sheet CURRENT OUTPUTS 0.0025 0.0010 AV = +15V DD 0.0008 AV = –15V SS T = 25°C A 0.0006 0.0015 0.0004 4mA TO 20mA RANGE MAX INL AV = +15V DD 0.0002 0mA TO 24mA RANGE MAX INL 0.0005 AV = –15V/0V SS 0mA TO 20mA RANGE MIN INL 0 0mA TO 20mA RANGE MAX INL 4mA TO 20mA RANGE MAX INL –0.0002 –0.0005 0mA TO 24mA RANGE MIN INL –0.0004 –0.0006 –0.0015 4mA TO 20mA, EXTERNAL R SET 4mA TO 20mA, EXTERNAL R , WITH DC-TO-DC CONVERTER SET –0.0008 4mA TO 20mA, INTERNAL R SET 4mA TO 20mA, INTERNAL R , WITH DC-TO-DC CONVERTER SET –0.0010 –0.0025 –40 –20 0 20 40 60 80 100 0 10000 20000 30000 40000 50000 60000 TEMPERATURE (°C) CODE Figure 32. Integral Nonlinearity vs. Code Figure 35. Integral Nonlinearity vs. Temperature, Internal RSET 0.0020 1.0 AV = +15V DD 4mA TO 20mA RANGE MAX INL 0.8 AV = –15V SS 0.0015 0mA TO 24mA RANGE MAX INL T = 25°C A 0mA TO 20mA RANGE MIN INL 0.6 0.0010 0.4 0.0005 0.2 0mA TO 20mA RANGE MAX INL 0 4mA TO 20mA RANGE MIN INL 0 0mA TO 24mA RANGE MIN INL –0.2 –0.0005 –0.4 –0.0010 –0.6 AV = +15V DD 4mA TO 20mA, EXTERNAL R SET –0.0015 AV = –15V/0V 4mA TO 20mA, EXTERNAL R , WITH DC-TO-DC CONVERTER SET SS –0.8 4mA TO 20mA, INTERNAL R SET 4mA TO 20mA, INTERNAL R , WITH DC-TO-DC CONVERTER SET –0.0020 –1.0 –40 –20 0 20 40 60 80 100 0 10000 20000 30000 40000 50000 60000 TEMPERATURE (°C) CODE Figure 33. Differential Nonlinearity vs. Code Figure 36. Integral Nonlinearity vs. Temperature, External R SET 0.035 1.0 AV = +15V DD 0.030 0.8 AV = –15V/0V SS ALL RANGES 0.025 0.6 INTERNAL AND EXTERNAL R SET AV = +15V 0.020 DD 0.4 AV = –15V SS T = 25°C A 0.015 0.2 ALL CHANNELS ENABLED DNL ERROR MAX 0.010 0 DNL ERROR MIN 4mA TO 20mA, EXTERNAL R SET 0.005 –0.2 4mA TO 20mA, EXTERNAL R , WITH DC-TO-DC CONVERTER SET 4mA TO 20mA, INTERNAL R SET 0 –0.4 4mA TO 20mA, INTERNAL R , WITH DC-TO-DC CONVERTER SET –0.005 –0.6 –0.010 –0.8 –0.015 –1.0 0 10000 20000 30000 40000 50000 60000 –40 –20 0 20 40 60 80 100 TEMPERATURE (°C) CODE Figure 37. Differential Nonlinearity vs. Temperature Figure 34. Total Unadjusted Error vs. Code Rev. C | Page 20 of 52 INL ERROR (%FSR) TOTAL UNADJUSTED ERROR (%FSR) DNL ERROR (LSB) 09226-150 09226-151 09226-149 INL ERROR (%FSR) INL ERROR (%FSR) DNL ERROR (LSB) 09226-154 09226-153 09226-152 Data Sheet AD5755-1 0.03 0.02 0.02 0.01 0.01 0 0 –0.01 –0.01 AV = +15V DD –0.02 AV = –15V/0V SS –0.02 AV = +15V –0.03 DD AV = –15V/0V SS –0.03 4mA TO 20mA INTERNAL R –0.04 SET 4mA TO 20mA INTERNAL R SET 0mA TO 20mA INTERNAL R SET 0mA TO 20mA INTERNAL R SET –0.05 0mA TO 24mA INTERNAL R SET –0.04 0mA TO 24mA INTERNAL R SET 4mA TO 20mA EXTERNAL R SET –0.06 4mA TO 20mA EXTERNAL R SET 0mA TO 20mA EXTERNAL R SET –0.05 0mA TO 20mA EXTERNAL R SET 0mA TO 24mA EXTERNAL R SET –0.07 0mA TO 24mA EXTERNAL R SET –0.08 –0.06 –40 –20 0 20 40 60 80 100 –40 –20 0 20 40 60 80 100 TEMPERATURE (°C) TEMPERATURE (°C) Figure 38. Total Unadjusted Error vs. Temperature Figure 41. Gain Error vs. Temperature 0.03 0.0025 4mA TO 20mA RANGE MAX INL 0.02 0.0020 4mA TO 20mA RANGE MIN INL T = 25°C A 0.01 AV = –26.4V FOR AV > +26.4V SS DD 0.0015 0 0.0010 –0.01 0.0005 –0.02 AV = +15V DD –0.03 AV = –15V/0V 0 SS –0.04 4mA TO 20mA INTERNAL R SET –0.0005 0mA TO 20mA INTERNAL R SET –0.05 0mA TO 24mA INTERNAL R SET –0.0010 4mA TO 20mA EXTERNAL R SET –0.06 0mA TO 20mA EXTERNAL R SET –0.0015 0mA TO 24mA EXTERNAL R –0.07 SET –0.08 –0.0020 –40 –20 0 20 40 60 80 100 10 15 20 25 30 SUPPLY (V) TEMPERATURE (°C) Figure 42. Integral Nonlinearity Error vs. AVDD/|AVSS|, Figure 39. Full Scale Error vs. Temperature Over Supply, External RSET 0.020 0.0015 0.015 0.0010 0.010 0.0005 0.005 0 0 –0.0005 AV = +15V DD AV = –15V/0V SS –0.0010 –0.005 4mA TO 20mA INTERNAL R SET 0mA TO 20mA INTERNAL R SET –0.0015 4mA TO 20mA RANGE MAX INL –0.010 0mA TO 24mA INTERNAL R SET 4mA TO 20mA RANGE MIN INL 4mA TO 20mA EXTERNAL R SET T = 25°C A –0.0020 –0.015 0mA TO 20mA EXTERNAL R SET AV = –26.4V FOR AV > +26.4V SS DD 0mA TO 24mA EXTERNAL R SET –0.0025 –0.020 10 15 20 25 30 –40 –20 0 20 40 60 80 100 SUPPLY (V) TEMPERATURE (°C) Figure 43. Integral Nonlinearity Error vs. AVDD/|AVSS|, Figure 40. Offset Error vs. Temperature Over Supply, Internal RSET Rev. C | Page 21 of 52 OFFSET ERROR (%FSR) FULL-SCALE ERROR (%FSR) TOTAL UNADJSUTED ERROR (%FSR) 09226-157 09226-155 09226-158 INL ERROR (%FSR) INL ERROR (%FSR) GAIN ERROR (%FSR) 09226-159 09226-057 09226-056 AD5755-1 Data Sheet 1.0 6 ALL RANGES AV = +15V DD 0.8 INTERNAL AND EXTERNAL R SET AV = –15V SS T = 25°C A 5 T = 25°C A 0.6 AV = –26.4V FOR AV > +26.4V SS DD R = 300Ω LOAD 0.4 4 0.2 DNL ERROR MAX 0 3 DNL ERROR MIN –0.2 2 –0.4 –0.6 1 –0.8 –1.0 0 10 15 20 25 30 0 5 10 15 20 SUPPLY (V) TIME (µs) Figure 44. Differential Nonlinearity Error vs. AV Figure 47. Output Current vs. Time on Power-Up DD 0.012 4 2 0.010 0 0.008 –2 0.006 –4 0.004 –6 AV = +15V DD 4mA TO 20mA RANGE MAX TUE AV = –15V SS 4mA TO 20mA RANGE MIN TUE T = 25°C 0.002 A T = 25°C –8 A R = 300Ω LOAD AV = –26.4V FOR AV > +26.4V SS DD INT_EN = 1 0 –10 0 1 2 3 4 5 6 10 15 20 25 30 SUPPLY (V) TIME (µs) Figure 48. Output Current vs. Time on Output Enable Figure 45. Total Unadjusted Error vs. AVDD, External RSET 0 30 –0.002 25 –0.004 –0.006 20 4mA TO 20mA RANGE MAX TUE –0.008 4mA TO 20mA RANGE MIN TUE T = 25°C A 15 I –0.010 OUT AV = –26.4V FOR AV > +26.4V SS DD V BOOST –0.012 10 0mA TO 24mA RANGE –0.014 1kΩ LOAD f = 410kHz SW –0.016 INDUCTOR = 10µH (XAL4040-103) 5 AV = 5V CC –0.018 T = 25°C A 0 –0.020 –0.50 –0.25 0 0.25 0.50 0.75 1.00 1.25 1.50 1.75 2.00 10 15 20 25 30 SUPPLY (V) TIME (ms) Figure 46. Total Unadjusted Error vs. AVDD, Internal RSET Figure 49. Output Current and VBOOST_x Settling Time with DC-to-DC Converter (See Figure 80) Rev. C | Page 22 of 52 TOTAL UNADJUSTED ERROR (%FSR) TOTAL UNADJUSTED ERROR (%FSR) DNL ERROR (LSB) 09226-162 09226-060 09226-061 CURRENT (µA) CURRENT (µA) OUTPUT CURRENT (mA) 09226-167 09226-063 09226-062 Data Sheet AD5755-1 30 8 0mA TO 24mA RANGE 7 1kΩ LOAD 25 F = 410kHz SW INDUCTOR = 10µH (XAL4040-103) 6 T = 25°C A 20 5 15 I , T = –40°C 4 OUT A I , T = +25°C OUT A I , T = +105°C OUT A 3 10 0mA TO 24mA RANGE 2 1kΩ LOAD 5 f = 410kHz SW 1 INDUCTOR = 10µH (XAL4040-103) AV = 5V CC 0 0 –0.25 0 0.25 0.50 0.75 1.00 1.25 1.50 1.75 0 5 10 15 20 CURRENT (mA) TIME (ms) Figure 50. Output Current Settling with DC-to-DC Converter vs. Time and Figure 53. DC-to-DC Converter Headroom vs. Output Current (See Figure 80) Temperature (See Figure 80) 30 0 AV = +15V DD V = +15V BOOST 25 –20 AV = –15V SS T = 25°C A 20 –40 15 I , AV = 4.5V OUT CC –60 I , AV = 5.0V OUT CC I , AV = 5.5V OUT CC 10 –80 0mA TO 24mA RANGE 1kΩ LOAD 5 f = 410kHz –100 SW INDUCTOR = 10µH (XAL4040-103) T = 25°C A 0 –120 –0.25 0 0.25 0.50 0.75 1.00 1.25 1.50 1.75 10 100 1k 10k 100k 1M 10M TIME (ms) FREQUENCY (Hz) Figure 51. Output Current Settling with DC-to-DC Converter vs. Time and Figure 54. IOUT_x PSRR vs. Frequency AVCC (See Figure 80) 10 20mA OUTPUT 10mA OUTPUT 8 6 4 2 0 –2 –4 –6 0mA TO 24mA RANGE AV = 5V 1kΩ LOAD –8 CC f = 410kHz EXTERNAL R SW SET INDUCTOR = 10µH (XAL4040-103) T = 25°C A –10 0 2 4 6 8 10 12 14 TIME (µs) Figure 52. Output Current vs. Time with DC-to-DC Converter (See Figure 80) Rev. C | Page 23 of 52 CURRENT (AC COUPLED) (µA) OUTPUT CURRENT (mA) OUTPUT CURRENT (mA) 09226-170 09226-169 09226-168 I PSRR (dB) OUT_x HEADROOM VOLTAGE (V) 09226-067 09226-068 AD5755-1 Data Sheet DC-TO-DC BLOCK 90 80 AV = 4.5V 20mA CC AV = 5V 85 CC AV = 5.5V 70 CC 80 60 75 70 50 65 40 0mA TO 24mA RANGE 0mA TO 24mA RANGE 1kΩ LOAD 1kΩ LOAD 60 EXTERNAL R EXTERNAL R SET SET f = 410kHz 30 AV = 5V SW CC 55 INDUCTOR = 10µH (XAL4040-103) f = 410 kHz SW T = 25°C INDUCTOR = 10µH (XAL4040-103) A 50 20 0 4 8 12 16 20 24 –40 –20 0 20 40 60 80 100 CURRENT (mA) TEMPERATURE (°C) Figure 55. Efficiency at VBOOST_x vs. Output Current (See Figure 80) Figure 58. Output Efficiency vs. Temperature (See Figure 80) 90 0.6 20mA 85 0.5 80 0.4 75 70 0.3 65 0mA TO 24mA RANGE 0.2 1kΩ LOAD EXTERNAL R 60 SET AV = 5V CC f = 410kHz 0.1 SW 55 INDUCTOR = 10µH (XAL4040-103) 50 0 –40 –20 0 20 40 60 80 100 –40 –20 0 20 40 60 80 100 TEMPERATURE (°C) TEMPERATURE (°C) Figure 56. Efficiency at V vs. Temperature (See Figure 80) BOOST_x Figure 59. Switch Resistance vs. Temperature 80 AV = 4.5V CC AV = 5V CC AV = 5.5V 70 CC 60 50 40 0mA TO 24mA RANGE 1kΩ LOAD EXTERNAL R SET 30 f = 410kHz SW INDUCTOR = 10µH (XAL4040-103) T = 25°C A 20 0 4 8 12 16 20 24 CURRENT (mA) Figure 57. Output Efficiency vs. Output Current (See Figure 80) Rev. C | Page 24 of 52 I EFFICIENCY (%) V EFFICIENCY (%) OUT_x BOOST_x V EFFICIENCY (%) BOOST_x 09226- 09226-017 017 09226-018 09226-016 I EFFICIENCY (%) SWITCH RESISTANCE (Ω) OUT_x 09226-123 09226-019 Data Sheet AD5755-1 REFERENCE 16 5.0050 AV DD 30 DEVICES SHOWN 5.0045 14 REF OUT AV = 15V DD T = 25°C A 5.0040 12 5.0035 10 5.0030 8 5.0025 6 5.0020 4 5.0015 2 5.0010 0 5.0005 –2 5.0000 –40 –20 0 20 40 60 80 100 0 0.2 0.4 0.6 0.8 1.0 1.2 TIME (ms) TEMPERATURE (°C) Figure 60. REFOUT Turn-On Transient Figure 63. REFOUT vs. Temperature (When the AD5755-1 is soldered onto a PCB, the reference shifts due to thermal shock on the package. The average output voltage shift is −4 mV. Measurement of these parts after seven days shows that the outputs typically shift back 2 mV toward their initial values. This second shift is due to the relaxation of stress incurred during soldering.) 4 5.002 AV = 15V DD AV = 15V DD T = 25°C A T = 25°C 3 5.001 A 2 5.000 1 4.999 0 4.998 –1 4.997 –2 4.996 –3 4.995 0 2 4 6 8 10 0 2 4 6 8 10 TIME (s) LOAD CURRENT (mA) Figure 61. REFOUT Output Noise (0.1 Hz to 10 Hz Bandwidth) Figure 64. REFOUT vs. Load Current 150 5.00000 AV = 15V DD T = 25°C A T = 25°C A 4.99995 100 4.99990 50 4.99985 0 4.99980 4.99975 –50 4.99970 –100 4.99965 –150 4.99960 0 5 10 15 20 10 15 20 25 30 TIME (ms) AV (V) DD Figure 62. REFOUT Output Noise (100 kHz Bandwidth) Figure 65. REFOUT vs. Supply Rev. C | Page 25 of 52 REFOUT (µV) VOLTAGE (V) REFOUT (µV) 09226-011 09226-012 09226-010 REFOUT (V) REFOUT (V) REFOUT (V) 09226-163 09226-014 09226-015 AD5755-1 Data Sheet GENERAL 450 13.4 DV = 5V CC 400 T = 25°C 13.3 A 350 13.2 300 13.1 250 13.0 200 12.9 150 12.8 100 12.7 DV = 5.5V CC 50 0 12.6 –40 –20 0 20 40 60 80 100 0 1 2 3 4 5 SDIN VOLTAGE (V) TEMPERATURE (°C) Figure 66. DI vs. Logic Input Voltage CC Figure 69. Internal Oscillator Frequency vs. Temperature 10 14.4 8 14.2 6 4 AI 14.0 DD AI SS 2 T = 25°C A V = 0V 13.8 OUT 0 OUTPUT UNLOADED –2 13.6 –4 13.4 –6 –8 13.2 DV = 5.5V CC –10 T = 25°C A 13.0 –12 2.5 3.0 3.5 4.0 4.5 5.0 5.5 10 15 20 25 30 VOLTAGE (V) VOLTAGE (V) Figure 67. AIDD/AISS vs. AVDD/|AVSS| Figure 70. Internal Oscillator Frequency vs. DVCC Supply Voltage 8 7 6 5 4 3 2 AI DD T = 25°C A 1 I = 0mA OUT 0 10 15 20 25 30 VOLTAGE (V) Figure 68. AIDD vs. AVDD Rev. C | Page 26 of 52 DI (µA) CURRENT (mA) CURRENT (mA) CC 09226-009 09226-008 09226-007 FREQUENCY (MHz) FREQUENCY (MHz) 09226-020 09226-021 Data Sheet AD5755-1 TERMINOLOGY Full-Scale Error Relative Accuracy or Integral Nonlinearity (INL) Full-scale error is a measure of the output error when full-scale For the DAC, relative accuracy, or integral nonlinearity, is a code is loaded to the DAC register. Ideally, the output should be measure of the maximum deviation, in LSBs, from the best fit full-scale − 1 LSB. Full-scale error is expressed in percent of line through the DAC transfer function. A typical INL vs. code full-scale range (% FSR). plot is shown in Figure 8. Full-Scale TC Differential Nonlinearity (DNL) Full-scale TC is a measure of the change in full-scale error with Differential nonlinearity (DNL) is the difference between the changes in temperature and is expressed in ppm FSR/°C. measured change and the ideal 1 LSB change between any two Total Unadjusted Error adjacent codes. A specified differential nonlinearity of ±1 LSB maximum ensures monotonicity. This DAC is guaranteed Total unadjusted error (TUE) is a measure of the output error monotonic by design. A typical DNL vs. code plot is shown in taking all the various errors into account, including INL error, Figure 9. offset error, gain error, temperature, and time. TUE is expressed in % FSR. Monotonicity A DAC is monotonic if the output either increases or remains DC Crosstalk constant for increasing digital input code. The AD5755-1 is This is the dc change in the output level of one DAC in response monotonic over its full operating temperature range. to a change in the output of another DAC. It is measured with a full-scale output change on one DAC while monitoring another Negative Full-Scale Error/Zero-Scale Error DAC, which is at midscale. Negative full-scale error is the error in the DAC output voltage when 0x0000 (straight binary coding) is loaded to the DAC Current Loop Compliance Voltage register. The maximum voltage at the I pin for which the output OUT_x current is equal to the programmed value. Zero-Scale TC This is a measure of the change in zero-scale error with a change in Voltage Reference Thermal Hysteresis temperature. Zero-scale error TC is expressed in ppm FSR/°C. Voltage reference thermal hysteresis is the difference in output voltage measured at +25°C compared to the output voltage Bipolar Zero Error measured at +25°C after cycling the temperature from +25°C to Bipolar zero error is the deviation of the analog output from the −40°C to +105°C and back to +25°C. The hysteresis is specified ideal half-scale output of 0 V when the DAC register is loaded for the first and second temperature cycles and is expressed in ppm. with 0x8000 (straight binary coding). Output Voltage Settling Time Bipolar Zero TC Output voltage settling time is the amount of time it takes for Bipolar zero TC is a measure of the change in the bipolar zero the output to settle to a specified level for a full-scale input error with a change in temperature. It is expressed in ppm change. A plot of settling time is shown in Figure 24, Figure 50, FSR/°C. and Figure 51. Offset Error Slew Rate In voltage output mode, offset error is the deviation of the The slew rate of a device is a limitation in the rate of change of analog output from the ideal quarter-scale output when in the output voltage. The output slewing speed of a voltage- bipolar output ranges and the DAC register is loaded with output digital-to-analog converter is usually limited by the slew 0x4000 (straight binary coding). rate of the amplifier used at its output. Slew rate is measured In current output mode, offset error is the deviation of the from 10% to 90% of the output signal and is given in V/µs. analog output from the ideal zero-scale output when all DAC Power-On Glitch Energy registers are loaded with 0x0000. Power-on glitch energy is the impulse injected into the analog Gain Error output when the AD5755-1 is powered-on. It is specified as the This is a measure of the span error of the DAC. It is the devia- area of the glitch in nV-sec. See Figure 29 and Figure 47. tion in slope of the DAC transfer characteristic from the ideal, Digital-to-Analog Glitch Impulse expressed in % FSR. Digital-to-analog glitch impulse is the impulse injected into the Gain TC analog output when the input code in the DAC register changes This is a measure of the change in gain error with changes in state, but the output voltage remains constant. It is normally temperature. Gain TC is expressed in ppm FSR/°C. specified as the area of the glitch in nV-sec and is measured when the digital input code is changed by 1 LSB at the major carry transition (~0x7FFF to 0x8000). See Figure 26. Rev. C | Page 27 of 52 AD5755-1 Data Sheet Glitch Impulse Peak Amplitude Line Regulation Glitch impulse peak amplitude is the peak amplitude of the Line regulation is the change in reference output voltage due to impulse injected into the analog output when the input code in a specified change in supply voltage. It is expressed in ppm/V. the DAC register changes state. It is specified as the amplitude Load Regulation of the glitch in mV and is measured when the digital input code Load regulation is the change in reference output voltage due to is changed by 1 LSB at the major carry transition (~0x7FFF to a specified change in load current. It is expressed in ppm/mA. 0x8000). See Figure 26. DC-to-DC Converter Headroom Digital Feedthrough This is the difference between the voltage required at the Digital feedthrough is a measure of the impulse injected into the current output and the voltage supplied by the dc-to-dc analog output of the DAC from the digital inputs of the DAC but is converter. See Figure 53. measured when the DAC output is not updated. It is specified Output Efficiency in nV-sec and measured with a full-scale code change on the 2 I × R data bus. LOAD OUT AV × AI DAC-to-DAC Crosstalk CC CC DAC-to-DAC crosstalk is the glitch impulse transferred to the This is defined as the power delivered to a channel’s load vs. the output of one DAC due to a digital code change and a subsequent power delivered to the channel’s dc-to-dc input. output change of another DAC. This includes both digital and Efficiency at VBOOST_x analog crosstalk. It is measured by loading one of the DACs I ×V OUT BOOST _ x with a full-scale code change (all 0s to all 1s and vice versa) with AV × AI CC CC LDAC low and monitoring the output of another DAC. The energy of the glitch is expressed in nV-sec. This is defined as the power delivered to a channel’s V BOOST_x supply vs. the power delivered to the channel’s dc-to-dc input. Power Supply Rejection Ratio (PSRR) The V quiescent current is considered part of the dc-to- BOOST_x PSRR indicates how the output of the DAC is affected by dc converter’s losses. changes in the power supply voltage. Reference TC Reference TC is a measure of the change in the reference output voltage with a change in temperature. It is expressed in ppm/°C. Rev. C | Page 28 of 52 Data Sheet AD5755-1 THEORY OF OPERATION V BOOST_x The AD5755-1 is a quad, precision digital-to-current loop and voltage output converter designed to meet the requirements of industrial process control applications. It provides a high precision, R2 R3 fully integrated, low cost, single-chip solution for generating T2 current loop and unipolar/bipolar voltage outputs. The current A2 ranges available are 0 mA to 20 mA, 0 mA to 24 mA, and 4 mA T1 16-BIT DAC to 20 mA. The voltage ranges available are 0 V to 5 V, ±5 V, 0 V I A1 OUT_x to 10 V, and ±10 V. The current and voltage outputs are availa- ble on separate pins, and only one is active at any one time. The R desired output configuration is user selectable via the DAC SET control register. Figure 73. Voltage-to-Current Conversion Circuitry On-chip dynamic power control minimizes package power dissipation in current mode. Voltage Output Amplifier DAC ARCHITECTURE The voltage output amplifier is capable of generating both unipolar and bipolar output voltages. It is capable of driving a The DAC core architecture of the AD5755-1 consists of two load of 1 kΩ in parallel with 1 µF (with an external compen- matched DAC sections. A simplified circuit diagram is shown sation capacitor) to AGND. The source and sink capabilities of in Figure 71. The four MSBs of the 16-bit data-word are the output amplifier are shown in Figure 23. The slew rate is decoded to drive 15 switches, E1 to E15. Each of these switches 1.9 V/µs with a full-scale settling time of 16 µs (10 V step). If connects one of 15 matched resistors to either ground or the remote sensing of the load is not required, connect +V SENSE_x reference buffer output. The remaining 12 bits of the data-word directly to VOUT_x. + VSENSE_x must stay within ±3.0 V of VOUT_x drive Switch S0 to Switch S11 of a 12-bit voltage mode R-2R for correct operation. ladder network. Driving Large Capacitive Loads V OUT 2R 2R 2R 2R 2R 2R 2R The voltage output amplifier is capable of driving capacitive S0 S1 S7/S11 E1 E2 E15 loads of up to 2 µF with the addition of a 220 pF nonpolarized compensation capacitor on each channel. Care should be taken to choose an appropriate value of compensation capacitor. This capacitor, while allowing the AD5755-1 to drive higher capaci- 12-BIT R-2R LADDER FOUR MSBs DECODED INTO tive loads and reduce overshoot, increases the settling time of 15 EQUAL SEGMENTS the part and, therefore, affects the bandwidth of the system. Figure 71. DAC Ladder Structure Without the compensation capacitor, up to 10 nF capacitive loads can be driven. See Table 5 for information on connecting The voltage output from the DAC core is either converted to a compensation capacitors. current (see Figure 73), which is then mirrored to the supply rail so that the application simply sees a current source output, or it Reference Buffers is buffered and scaled to output a software selectable unipolar or The AD5755-1 can operate with either an external or internal bipolar voltage range (see Figure 72). Both the voltage and current reference. The reference input requires a 5 V reference for outputs are supplied by V . The current and voltage are BOOST_x specified performance. This input voltage is then buffered output on separate pins and cannot be output simultaneously. before it is applied to the DAC. A channel’s current and voltage output pins can be tied together. POWER-ON STATE OF THE AD5755-1 +V SENSE_x On initial power-up of the AD5755-1, the power-on reset circuit powers up in a state that is dependent on the power-on RANGE V OUT_x DAC SCALING condition (POC) pin. V SHORT FAULT If POC = 0, the voltage output and current output channels OUT_X power up in tristate mode. Figure 72. Voltage Output If POC = 1, the voltage output channel powers up with a 30 kΩ pull-down resistor to ground, and the current output channel powers up to tristate. Even though the output ranges are not enabled, the default output range is 0 V to 5 V, and the clear code register is loaded Rev. C | Page 29 of 52 09226-069 09226-070 09226-071 AD5755-1 Data Sheet OUTPUT with all zeros. This means that if the user clears the part after I/V AMPLIFIER power-up, the output is actively driven to 0 V (if the channel V 16-BIT REFIN V OUT_x DAC has been enabled for clear). After a device power on, or a device reset, it is recommended to DAC wait 100 μs or more before writing to the device to allow time LDAC REGISTER for internal calibrations to take place. SERIAL INTERFACE DAC INPUT REGISTER The AD5755-1 is controlled over a versatile 3-wire serial OFFSET AND GAIN interface that operates at clock rates of up to 30 MHz and is CALIBRATION compatible with SPI, QSPI, MICROWIRE, and DSP standards. DAC DATA REGISTER Data coding is always straight binary. Input Shift Register SCLK INTERFACE SDO SYNC The input shift register is 24 bits wide. Data is loaded into the LOGIC SDIN device MSB first as a 24-bit word under the control of a serial Figure 74. Simplified Serial Interface of Input Loading Circuitry clock input, SCLK. Data is clocked in on the falling edge of SCLK. for One DAC Channel If packet error checking, or PEC (see the Device Features TRANSFER FUNCTION section), is enabled, an additional eight bits must be written to Table 6 shows the input code to ideal output voltage relationship the AD5755-1, creating a 32-bit serial interface. for the AD5755-1 for straight binary data coding of the ±10 V There are two ways in which the DAC outputs can be updated: output range. individual updating or simultaneous updating of all DACs. Table 6. Ideal Output Voltage to Input Code Relationship Individual DAC Updating Digital Input In this mode, LDAC is held low while data is being clocked into Straight Binary Data Coding Analog Output the DAC data register. The addressed DAC output is updated on MSB LSB VOUT SYNC the rising edge of . See Table 3 and Figure 3 for timing 1111 1111 1111 1111 +2 VREF × (32,767/32,768) information. 1111 1111 1111 1110 +2 V × (32,766/32,768) REF 1000 0000 0000 0000 0 V Simultaneous Updating of All DACs 0000 0000 0000 0001 −2 V × (32,767/32,768) REF In this mode, LDAC is held high while data is being clocked 0000 0000 0000 0000 −2 VREF into the DAC data register. Only the first write to each channel’s LDAC DAC data register is valid after is brought high. Any subse- LDAC quent writes while is still held high are ignored, though they are loaded into the DAC data register. All the DAC outputs are updated by taking LDAC low after SYNC is taken high. Rev. C | Page 30 of 52 09226-072 Data Sheet AD5755-1 REGISTERS Table 7 shows an overview of the registers for the AD5755-1. Table 7. Data, Control, and Readback Registers for the AD5755-1 Register Description Data DAC Data Register (×4) Used to write a DAC code to each DAC channel. AD5755-1 data bits = D15 to D0. There are four DAC data registers, one per DAC channel. Gain Register (×4) Used to program gain trim, on a per channel basis. AD5755-1 data bits = D15 to D0. There are four gain registers, one per DAC channel. Offset Register (×4) Used to program offset trim, on a per channel basis. AD5755-1 data bits = D15 to D0. There are four offset registers, one per DAC channel. Clear Code Register (×4) Used to program clear code on a per channel basis. AD5755-1 data bits = D15 to D0. There are four clear code registers, one per DAC channel. Control Main Control Register Used to configure the part for main operation. Sets functions such as status readback during write, enables output on all channels simultaneously, powers on all dc-to-dc converter blocks simultaneously, and enables and sets conditions of the watchdog timer. See the Device Features section for more details. Software Register Has three functions. Used to perform a reset, to toggle the user bit, and, as part of the watchdog timer feature, to verify correct data communication operation. Slew Rate Control Register (×4) Used to program the slew rate of the output. There are four slew rate control registers, one per channel. DAC Control Register (×4) These registers are used to control the following: Set the output range, for example, 4 mA to 20 mA, 0 V to 10 V. Set whether an internal/external sense resistor is used. Enable/disable a channel for CLEAR. Enable/disable overrange. Enable/disable internal circuitry on a per channel basis. Enable/disable output on a per channel basis. Power on dc-to-dc converters on a per channel basis. There are four DAC control registers, one per DAC channel. DC-to-DC Control Register Use to set the dc-to-dc control parameters. Can control dc-to-dc maximum voltage, phase, and frequency. Readback Status Register This contains any fault information, as well as a user toggle bit. Rev. C | Page 31 of 52 AD5755-1 Data Sheet PROGRAMMING SEQUENCE TO WRITE/ENABLE CHANGING AND REPROGRAMMING THE RANGE THE OUTPUT CORRECTLY When changing between ranges, the same sequence as To correctly write to and set up the part from a power-on described in the Programming Sequence to Write/Enable the Output Correctly section should be used. It is recommended to condition, use the following sequence: set the range to its zero point (can be midscale or zero scale) 1. Perform a hardware or software reset after initial power-on. prior to disabling the output. Because the dc-to-dc switching 2. The dc-to-dc converter supply block must be configured. frequency, maximum voltage, and phase have already been Set the dc-to-dc switching frequency, maximum output selected, there is no need to reprogram these. A flowchart of voltage allowed, and the phase that the four dc-to-dc this sequence is shown in Figure 76. channels clock at. 3. Configure the DAC control register on a per channel basis. CHANNEL’S OUTPUT IS ENABLED. The output range is selected, and the dc-to-dc converter block is enabled (DC_DC bit). Other control bits can be STEP 1: WRITE TO CHANNEL’S DAC DATA REGISTER. SET THE OUTPUT configured at this point. Set the INT_ENABLE bit; however, TO 0V (ZERO OR MIDSCALE). the output enable bit (OUTEN) should not be set. 4. Write the required code to the DAC data register. This STEP 2: WRITE TO DAC CONTROL REGISTER. implements a full DAC calibration internally. Allow at least DISABLE THE OUTPUT (OUTEN = 0), AND SET THE NEW OUTPUT RANGE. KEEP THE 200 µs before Step 5 for reduced output glitch. DC_DC BIT AND THE INT_ENABLE BIT SET. 5. Write to the DAC control register again to enable the output (set the OUTEN bit). STEP 3: WRITE VALUE TO THE DAC DATA REGISTER. A flowchart of this sequence is shown in Figure 75. STEP 4: WRITE TO DAC CONTROL REGISTER. POWER ON. RELOAD SEQUENCE AS IN STEP 2 ABOVE. THIS TIME SELECT THE OUTEN BIT TO ENABLE THE OUTPUT. STEP 1: PERFORM A SOFTWARE/HARDWARE RESET. Figure 76. Steps for Changing the Output Range STEP 2: WRITE TO DC-TO-DC CONTROL REGISTER TO SET DC-TO-DC CLOCK FREQUENCY, PHASE, AND MAXIMUM VOLTAGE. STEP 3: WRITE TO DAC CONTROL REGISTER. SELECT THE DAC CHANNEL AND OUTPUT RANGE. SET THE DC_DC BIT AND OTHER CONTROL BITS AS REQUIRED. SET THE INT_ENABLE BIT BUT DO NOT SELECT THE OUTEN BIT. STEP 4: WRITE TO EACH/ALL DAC DATA REGISTERS. ALLOW AT LEAST 200µs BETWEEN STEP 3 AND STEP 5 FOR REDUCED OUTPUT GLITCH. STEP 5: WRITE TO DAC CONTROL REGISTER. RELOAD SEQUENCE AS IN STEP 3 ABOVE. THIS TIME SELECT THE OUTEN BIT TO ENABLE THE OUTPUT. Figure 75. Programming Sequence for Enabling the Output Correctly Rev. C | Page 32 of 52 09226-073 09226-074 Data Sheet AD5755-1 DATA REGISTERS The input register is 24 bits wide. When PEC is enabled, the DAC Data Register input register is 32 bits wide, with the last eight bits correspond- When writing to the AD5755-1 DAC data registers, D15 to D0 ing to the PEC code (see the Packet Error Checking section for are used for DAC data bits. Table 10 shows the register format more information on PEC). When writing to a data register, the and Table 9 describes the function of Bit D23 to Bit D16. format in Table 8 must be used. Table 8. Writing to a Data Register MSB LSB D23 D22 D21 D20 D19 D18 D17 D16 D15 to D0 R/ DUT_AD1 DUT_AD0 DREG2 DREG1 DREG0 DAC_AD1 DAC_AD0 Data W Table 9. Input Register Decode Bit Description R/W Indicates a read from or a write to the addressed register. DUT_AD1, DUT_AD0 Used in association with the external pins, AD1 and AD0, to determine which AD5755-1 device is being addressed by the system controller. DUT_AD1 DUT_AD0 Function 0 0 Addresses part with Pin AD1 = 0, Pin AD0 = 0 0 1 Addresses part with Pin AD1 = 0, Pin AD0 = 1 1 0 Addresses part with Pin AD1 = 1, Pin AD0 = 0 1 1 Addresses part with Pin AD1 = 1, Pin AD0 = 1 DREG2, DREG1, DREG0 Selects whether a data register or a control register is written to. If a control register is selected, a further decode of CREG bits (see Table 17) is required to select the particular control register, as follows. DREG2 DREG1 DREG0 Function 0 0 0 Write to DAC data register (individual channel write) 0 1 0 Write to gain register 0 1 1 Write to gain register (all DACs) 1 0 0 Write to offset register 1 0 1 Write to offset register (all DACs) 1 1 0 Write to clear code register 1 1 1 Write to a control register DAC_AD1, DAC_AD0 These bits are used to decode the DAC channel. DAC_AD1 DAC_AD0 DAC Channel/Register Address 0 0 DAC A 0 1 DAC B 1 0 DAC C 1 1 DAC D X X These are don’t cares if they are not relevant to the operation being performed. Table 10. Programming the DAC Data Registers MSB LSB D23 D22 D21 D20 D19 D18 D17 D16 D15 to D0 R/W DUT_AD1 DUT_AD0 DREG2 DREG1 DREG0 DAC_AD1 DAC_AD0 DAC data Rev. C | Page 33 of 52 AD5755-1 Data Sheet in steps of 1 LSB. This is done by setting the DREG[2:0] bits to Gain Register 100. It is possible to write the same offset code to all four DAC The 16-bit gain register, as shown in Table 11, allows the user to channels at the same time by setting the DREG[2:0] bits to 101. adjust the gain of each channel in steps of 1 LSB. This is done by The offset register coding is straight binary as shown in Table 14. setting the DREG[2:0] bits to 010. It is possible to write the The default code in the offset register is 0x8000, which results in same gain code to all four DAC channels at the same time by zero offset programmed to the output. See the Digital Offset setting the DREG[2:0] bits to 011. The gain register coding is and Gain Control section for more information. straight binary as shown in Table 12. The default code in the Clear Code Register gain register is 0xFFFF. In theory, the gain can be tuned across the full range of the output. In practice, the maximum The 16-bit clear code register allows the user to set the clear recommended gain trim is about 50% of programmed range to value of each channel as shown in Table 15. It is possible, via maintain accuracy. See the Digital Offset and Gain Control software, to enable or disable on a per channel basis which section for more information. channels are cleared when the CLEAR pin is activated. The default clear code is 0x0000. See the Asynchronous Clear Offset Register section for more information. The 16-bit offset register, as shown in Table 13, allows the user to adjust the offset of each channel by −32,768 LSBs to +32,767 LSBs Table 11. Programming the Gain Register R/W DUT_AD1 DUT_AD0 DREG2 DREG1 DREG0 DAC_AD1 DAC_AD0 D15 to D0 0 Device address 0 1 0 DAC channel address Gain adjustment Table 12. Gain Register Gain Adjustment G15 G14 G13 G12 to G4 G3 G2 G1 G0 +65,535 LSBs 1 1 1 1 1 1 1 1 +65,534 LSBs 1 1 1 1 1 1 0 0 … … … … … … … … … 1 LSB 0 0 0 0 0 0 0 1 0 LSBs 0 0 0 0 0 0 0 0 Table 13. Programming the Offset Register R/W DUT_AD1 DUT_AD0 DREG2 DREG1 DREG0 DAC_AD1 DAC_AD0 D15 to D0 0 Device address 1 0 0 DAC channel address Offset adjustment Table 14. Offset Register Options Offset Adjustment OF15 OF14 OF13 OF12 to OF4 OF3 OF2 OF1 OF0 +32,767 LSBs 1 1 1 1 1 1 1 1 +32,766 LSBs 1 1 1 1 1 1 0 0 … … … … … … … … … No Adjustment (Default) 1 0 0 0 0 0 0 0 … … … … … … … … … −32,767 LSBs 0 0 0 0 0 0 0 0 −32,768 LSBs 0 0 0 0 0 0 0 0 Table 15. Programming the Clear Code Register R/W DUT_AD1 DUT_AD0 DREG2 DREG1 DREG0 DAC_AD1 DAC_AD0 D15 to D0 0 Device address 1 1 0 DAC channel address Clear code Rev. C | Page 34 of 52 Data Sheet AD5755-1 CONTROL REGISTERS When writing to a control register, the format shown in Table 16 Main Control Register must be used. See Table 9 for information on the configuration The main control register options are shown in Table 18 and of Bit D23 to Bit D16. The control registers are addressed by Table 19. See the Device Features section for more information setting the DREG[2:0] bits to 111 and then setting the on the features controlled by the main control register. CREG[2:0] bits to the appropriate decode address for that register, according to Table 17. These CREG bits select among the various control registers. Table 16. Writing to a Control Register MSB LSB D23 D22 D21 D20 D19 D18 D17 D16 D15 D14 D13 D12 to D0 R/W DUT_AD1 DUT_AD0 1 1 1 DAC_AD1 DAC_AD0 CREG2 CREG1 CREG0 Data Table 17. Register Access Decode CREG2 (D15) CREG1 (D14) CREG0 (D13) Function 0 0 0 Slew rate control register (one per channel) 0 0 1 Main control register 0 1 0 DAC control register (one per channel) 0 1 1 DC-to-dc control register 1 0 0 Software register Table 18. Programming the Main Control Register MSB LSB D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 to D0 1 1 0 0 1 POC STATREAD EWD WD1 WD0 X ShtCctLim OUTEN_ALL DCDC_ALL X 1 X = don’t care. Table 19. Main Control Register Functions Bit Description POC The POC bit determines the state of the voltage output channels during normal operation. Its default value is 0. POC = 0. The output goes to the value set by the POC hardware pin when the voltage output is not enabled (default). POC = 1. The output goes to the opposite value of the POC hardware pin if the voltage output is not enabled. STATREAD Enable status readback during a write. See the Device Features section. STATREAD = 1, enable. STATREAD = 0, disable (default). EWD Enable watchdog timer. See the Device Features section for more information. EWD = 1, enable watchdog. EWD = 0, disable watchdog (default). WD1, WD0 Timeout select bits. Used to select the timeout period for the watchdog timer. WD1 WD0 Timeout Period (ms) 0 0 5 0 1 10 1 0 100 1 1 200 ShtCctLim Programmable short-circuit limit on the V pin in the event of a short-circuit condition. OUT_x 0 = 16 mA (default). 1 = 8 mA. OUTEN_ALL Enables the output on all four DACs simultaneously. Do not use the OUTEN_ALL bit when using the OUTEN bit in the DAC control register. DCDC_ALL When set, powers up the dc-to-dc converter on all four channels simultaneously. To power down the dc-to-dc converters, all channel outputs must first be disabled. Do not use the DCDC_ALL bit when using the DC_DC bit in the DAC control register. Rev. C | Page 35 of 52 AD5755-1 Data Sheet DAC Control Register The DAC control register is used to configure each DAC channel. The DAC control register options are shown in Table 20 and Table 21. Table 20. Programming DAC Control Register D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 1 1 1 1 0 1 0 X X X X INT_ENABLE CLR_EN OUTEN RSET DC_DC OVRNG R2 R1 R0 1 X = don’t care. Table 21. DAC Control Register Functions Bit Description INT_ENABLE Powers up the dc-to-dc converter, DAC, and internal amplifiers for the selected channel. Does not enable the output. Can only be done on a per channel basis. It is recommended to set this bit and allow a >200 µs delay before enabling the output because this results in a reduced output enable glitch. See Figure 30 and Figure 48 for plots of this glitch. CLR_EN Per channel clear enable bit. Selects if this channel clears when the CLEAR pin is activated. CLR_EN = 1, channel clears when the part is cleared. CLR_EN = 0, channel does not clear when the part is cleared (default). OUTEN Enables/disables the selected output channel. OUTEN = 1, enables the channel. OUTEN = 0, disables the channel (default). RSET Selects an internal or external current sense resistor for the selected DAC channel. RSET = 0, selects the external resistor (default). RSET = 1, selects the internal resistor. DC_DC Powers the dc-to-dc converter on the selected channel. DC_DC = 1, power up the dc-to-dc converter. DC_DC = 0, power down the dc-to-dc converter (default). This allows per channel dc-to-dc converter power-up/power-down. To power down the dc-to-dc converter, the OUTEN and INT_ENABLE bits must also be set to 0. All dc-to-dc converters can also be powered up simultaneously using the DCDC_ALL bit in the main control register. OVRNG Enables 20% overrange on voltage output channel only. No current output overrange available. OVRNG = 1, enabled. OVRNG = 0, disabled (default). R2, R1, R0 Selects the output range to be enabled. R2 R1 R0 Output Range Selected 0 0 0 0 V to 5 V voltage range (default). 0 0 1 0 V to 10 V voltage range. 0 1 0 ±5 V voltage range. 0 1 1 ±10 V voltage range. 1 0 0 4 mA to 20 mA current range. 1 0 1 0 mA to 20 mA current range. 1 1 0 0 mA to 24 mA current range. Rev. C | Page 36 of 52 Data Sheet AD5755-1 When the watchdog feature is enabled, the user must write Software Register 0x195 to the software register within the timeout period. If this The software register has three functions. It allows the user to command is not received within the timeout period, the ALERT perform a software reset to the part. It can be used to set the pin signals a fault condition. This is only required when the user toggle bit, D11, in the status register. It is also used as part watchdog timer function is enabled. of the watchdog feature when it is enabled. This feature is useful DC-to-DC Control Register to ensure that communication has not been lost between the MCU and the AD5755-1 and that the datapath lines are working The dc-to-dc control register allows the user control over properly (that is, SDIN, SCLK, and SYNC). the dc-to-dc switching frequency and phase, as well as the maximum allowable dc-to-dc output voltage. The dc-to-dc control register options are shown in Table 24 and Table 25. Table 22. Programming the Software Register MSB LSB D15 D14 D13 D12 D11 to D0 1 0 0 User program Reset code/SPI code Table 23. Software Register Functions Bit Description User Program This bit is mapped to Bit D11 of the status register. When this bit is set to 1, Bit D11 of the status register is set to 1. Likewise, when D12 is set to 0, Bit D11 of the status register is also set to zero. This feature can be used to ensure that the SPI pins are working correctly by writing a known bit value to this register and reading back the corresponding bit from the status register. Reset Code/SPI Code Option Description Reset code Writing 0x555 to D[11:0] performs a reset of the AD5755-1. SPI code If the watchdog timer feature is enabled, 0x195 must be written to the software register (D11 to D0) within the programmed timeout period. Table 24. Programming the DC-to-DC Control Register MSB LSB D15 D14 D13 D12 to D7 D6 D5 to D4 D3 to D2 D1 to D0 1 0 1 1 X DC-DC Comp DC-DC phase DC-DC Freq DC-DC MaxV 1 X = don’t care. Table 25. DC-to-DC Control Register Options Bit Description DC-DC Comp Selects between an internal and external compensation resistor for the dc-to-dc converter. See the DC-to-DC Converter Compensation Capacitors and AICC Supply Requirements—Slewing sections in the Device Features section for more information. 0 = selects the internal 150 kΩ compensation resistor (default). 1 = bypasses the internal compensation resistor for the dc-to-dc converter. In this mode, an external dc-to-dc compensation resistor must be used; this is placed at the COMP pin in series with the 10 nF dc-to-dc compensation DCDC_x capacitor to ground. Typically, a ~50 kΩ resistor is recommended. DC-DC Phase User programmable dc-to-dc converter phase (between channels). 00 = all dc-to-dc converters clock on the same edge (default). 01 = Channel A and Channel B clock on the same edge, Channel C and Channel D clock on opposite edges. 10 = Channel A and Channel C clock on the same edge, Channel B and Channel D clock on opposite edges. 11 = Channel A, Channel B, Channel C, and Channel D clock 90° out of phase from each other. DC-DC Freq DC-to-dc switching frequency; these are divided down from the internal 13 MHz oscillator (see Figure 69 and Figure 70). 00 = 250 ± 10% kHz. 01 = 410 ± 10% kHz (default). 10 = 650 ± 10% kHz. DC-DC MaxV Maximum allowed VBOOST_x voltage supplied by the dc-to-dc converter. 00 = 23 V + 1 V/−1.5 V (default). 01 = 24.5 V ± 1 V. 10 = 27 V ± 1 V. 11 = 29.5 V ± 1V. Rev. C | Page 37 of 52 AD5755-1 Data Sheet request to read yet another register on a third data transfer or a Slew Rate Control Register no operation command. The no operation command for DUT This register is used to program the slew rate control for the Address 00 is 0x1CE000, for other DUT addresses, Bits D22 and selected DAC channel. This feature is available on both the D21 are set accordingly. current and voltage outputs. The slew rate control is enabled/ Readback Example disabled and programmed on a per channel basis. See Table 26 and the Digital Slew Rate Control section for more information. To read back the gain register of Device 1, Channel A on the AD5755-1, implement the following sequence: READBACK OPERATION 1. Write 0xA80000 to the AD5755-1 input register. This Readback mode is invoked by setting the R/W bit = 1 in the configures the AD5755-1 Device Address 1 for read mode serial input register write. See Table 27 for the bits associated with the gain register of Channel A selected. All the data with a readback operation. The DUT_AD1 and DUT_AD0 bits, bits, D15 to D0, are don’t cares. in association with Bits RD[4:0], select the register to be read. 2. Follow with another read command or a no operation The remaining data bits in the write sequence are don’t cares. command (0x3CE000). During this command, the data During the next SPI transfer (see Figure 4), the data appearing from the Channel A gain register is clocked out on the on the SDO output contains the data from the previously SDO line. addressed register. This second SPI transfer should either be a Table 26. Programming the Slew Rate Control Register D15 D14 D13 D12 D11 to D7 D6 to D3 D2 to D0 1 0 0 0 SREN X SR_CLOCK SR_STEP 1 X = don’t care. Table 27. Input Shift Register Contents for a Read Operation D23 D22 D21 D20 D19 D18 D17 D16 D15 to D0 1 R/W DUT_AD1 DUT_AD0 RD4 RD3 RD2 RD1 RD0 X 1 X = don’t care. Table 28. Read Address Decoding RD4 RD3 RD2 RD1 RD0 Function 0 0 0 0 0 Read DAC A data register 0 0 0 0 1 Read DAC B data register 0 0 0 1 0 Read DAC C data register 0 0 0 1 1 Read DAC D data register 0 0 1 0 0 Read DAC A control register 0 0 1 0 1 Read DAC B control register 0 0 1 1 0 Read DAC C control register 0 0 1 1 1 Read DAC D control register 0 1 0 0 0 Read DAC A gain register 0 1 0 0 1 Read DAC B gain register 0 1 0 1 0 Read DAC C gain register 0 1 0 1 1 Read DAC D gain register 0 1 1 0 0 Read DACA offset register 0 1 1 0 1 Read DAC B offset register 0 1 1 1 0 Read DAC C offset register 0 1 1 1 1 Read DAC D offset register 1 0 0 0 0 Clear DAC A code register 1 0 0 0 1 Clear DAC B code register 1 0 0 1 0 Clear DAC C code register 1 0 0 1 1 Clear DAC D code register 1 0 1 0 0 DAC A slew rate control register 1 0 1 0 1 DAC B slew rate control register 1 0 1 1 0 DAC C slew rate control register 1 0 1 1 1 DAC D slew rate control register 1 1 0 0 0 Read status register 1 1 0 0 1 Read main control register 1 1 0 1 0 Read dc-to-dc control register Rev. C | Page 38 of 52 Data Sheet AD5755-1 Status Register the SDO pin during every write sequence. Alternatively, if the The status register is a read only register. This register contains STATREAD bit is not set, the status register can be read using any fault information as a well as a ramp active bit and a user the normal readback operation. toggle bit. When the STATREAD bit in the main control register is set, the status register contents can be read back on Table 29. Decoding the Status Register MSB LSB D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 DC- DC- DC- DC- User PEC Ramp Over VOUT_D VOUT_C VOUT_B VOUT_A IOUT_D IOUT_C IOUT_B IOUT_A DCD DCC DCB DCA toggle error active TEMP fault fault fault fault fault fault fault fault Table 30. Status Register Options Bit Description DC-DCD In current output mode, this bit is set on Channel D if the dc-to-dc converter cannot maintain compliance (it may be reaching its V voltage). In this case, the I fault bit is also set. See the DC-to-DC Converter V Functionality section MAX OUT_D MAX for more information on this bit’s operation under this condition. In voltage output mode, this bit is set if, on Channel D, the dc-to-dc converter is unable to regulate to 15 V as expected. FAULT When this bit is set, it does not result in the pin going high. DC-DCC In current output mode, this bit is set on Channel C if the dc-to-dc converter cannot maintain compliance (it may be reaching its VMAX voltage). In this case, the IOUT_C fault bit is also set. See the DC-to-DC Converter VMAX Functionality section for more information on this bit’s operation under this condition. In voltage output mode, this bit is set if, on Channel C, the dc-to-dc converter is unable to regulate to 15 V as expected. FAULT When this bit is set, it does not result in the pin going high. DC-DCB In current output mode, this bit is set on Channel B if the dc-to-dc converter cannot maintain compliance (it may be reaching its VMAX voltage). In this case, the IOUT_B fault bit is also set. See the DC-to-DC Converter VMAX Functionality section for more information on this bit’s operation under this condition. In voltage output mode, this bit is set if, on Channel B, the dc-to-dc converter is unable to regulate to 15 V as expected. FAULT When this bit is set, it does not result in the pin going high. DC-DCA In current output mode, this bit is set on Channel A if the dc-to-dc converter cannot maintain compliance (it may be reaching its V voltage). In this case, the I fault bit is also set. See the DC-to-DC Converter V Functionality section for MAX OUT_A MAX more information on this bit’s operation under this condition. In voltage output mode, this bit is set if, on Channel A, the dc-to-dc converter is unable to regulate to 15 V as expected. FAULT When this bit is set, it does not result in the pin going high. User Toggle User toggle bit. This bit is set or cleared via the software register. This can be used to verify data communications if needed. PEC Error Denotes a PEC error on the last data-word received over the SPI interface. Ramp Active This bit is set while any one of the output channels is slewing (slew rate control is enabled on at least one channel). Over TEMP This bit is set if the AD5755-1 core temperature exceeds approximately 150°C. VOUT_D Fault This bit is set if a fault is detected on the VOUT_D pin. VOUT_C Fault This bit is set if a fault is detected on the VOUT_C pin. VOUT_B Fault This bit is set if a fault is detected on the VOUT_B pin. V Fault This bit is set if a fault is detected on the V pin. OUT_A OUT_A I Fault This bit is set if a fault is detected on the I pin. OUT_D OUT_D I Fault This bit is set if a fault is detected on the I pin. OUT_C OUT_C I Fault This bit is set if a fault is detected on the I pin. OUT_B OUT_B I Fault This bit is set if a fault is detected on the I pin. OUT_A OUT_A Rev. C | Page 39 of 52 AD5755-1 Data Sheet DEVICE FEATURES DAC DAC DATA OUTPUT FAULT DAC INPUT REGISTER REGISTER FAULT The AD5755-1 is equipped with a pin, an active low M open-drain output allowing several AD5755-1 devices to be REGISTER connected together to one pull-up resistor for global fault C detection. The FAULT pin is forced active by any one of the REGISTER following fault scenarios: Figure 77. Digital Offset and Gain control • The voltage at IOUT_x attempts to rise above the compliance Although Figure 77 indicates a multiplier and adder for each range due to an open-loop circuit or insufficient power channel, there is only one multiplier and one adder in the device, supply voltage. The internal circuitry that develops the and they are shared among all four channels. This has fault output avoids using a comparator with windowed implications for the update speed when several channels are limits because this requires an actual output error before updated at once (see Table 3). FAULT the output becomes active. Instead, the signal is Each time data is written to the M or C register, the output is generated when the internal amplifier in the output stage not automatically updated. Instead, the next write to the DAC has less than approximately 1 V of remaining drive channel uses these M and C values to perform a new calibration capability. Thus, the FAULT output activates slightly before and automatically updates the channel. the compliance limit is reached. The output data from the calibration is routed to the DAC input • A short is detected on a voltage output pin. The short- circuit current is limited to 16 mA or 8 mA, which is register. This is then loaded to the DAC as described in the programmable by the user. If using the AD5755-1 in Theory of Operation section. Both the gain register and the unipolar supply mode, a short-circuit fault may be offset register have 16 bits of resolution. The correct method to generated if the output voltage is below 50 mV. calibrate the gain/offset is to first calibrate out the gain and then calibrate the offset. • An interface error is detected due to a PEC failure. See the Packet Error Checking section. The value (in decimal) that is written to the DAC input register • If the core temperature of the AD5755-1 exceeds can be calculated by approximately 150°C. (M+ 1) 15 Code = D× + C− 2 (1) DACRegister 16 The VOUT_x fault, IOUT_x fault, PEC error, and over TEMP bits 2 of the status register are used in conjunction with the FAULT where: output to inform the user which one of the fault conditions D is the code loaded to the DAC channel’s input register. FAULT caused the output to be activated. 16 M is the code in the gain register (default code = 2 – 1). 15 VOLTAGE OUTPUT SHORT-CIRCUIT PROTECTION C is the code in the offset register (default code = 2 ). Under normal operation, the voltage output sinks/sources up STATUS READBACK DURING A WRITE to 12 mA and maintains specified operation. The maximum The AD5755-1 has the ability to read back the status register output current or short-circuit current is programmable by contents during every write sequence. This feature is enabled the user and can be set to 16 mA or 8 mA. If a short circuit is via the STATREAD bit in the main control register. This allows detected, the FAULT goes low and the relevant V fault bit OUT_x the user to continuously monitor the status register and act in the status register is set. quickly in the case of a fault. DIGITAL OFFSET AND GAIN CONTROL When status readback during a write is enabled, the contents of Each DAC channel has a gain (M) and offset (C) register, which the 16-bit status register (see Table 30) are output on the SDO allow trimming out of the gain and offset errors of the entire pin, as shown in Figure 5. signal chain. Data from the DAC data register is operated on by The AD5755-1 powers up with this feature disabled. When this a digital multiplier and adder controlled by the contents of the is enabled, the normal readback feature is not available, except M and C registers. The calibrated DAC data is then stored in the for the status register. To read back any other register, clear the DAC input register. STATREAD bit first before following the readback sequence. STATREAD can be set high again after the register read. Rev. C | Page 40 of 52 09226-075 Data Sheet AD5755-1 disabled, the user can still use the normal readback operation to ASYNCHRONOUS CLEAR monitor status register activity with PEC. CLEAR is an active high, edge-sensitive input that allows the output to be cleared to a preprogrammed 16-bit code. This code WATCHDOG TIMER is user programmable via a per channel 16-bit clear code register. When enabled, an on-chip watchdog timer generates an alert For a channel to clear, that channel must be enabled to be signal if 0x195 has not been written to the software register cleared via the CLR_EN bit in the channel’s DAC control within the programmed timeout period. This feature is useful to register. If the channel is not enabled to be cleared, then ensure that communication has not been lost between the MCU the output remains in its current state independent of the and the AD5755-1 and that these datapath lines are working CLEAR pin level. properly (that is, SDIN, SCLK, and SYNC). If 0x195 is not received by the software register within the timeout period, the When the CLEAR signal is returned low, the relevant outputs ALERT pin signals a fault condition. The ALERT signal is active remain cleared until a new value is programmed. high and can be connected directly to the CLEAR pin to enable PACKET ERROR CHECKING a clear in the event that communication from the MCU is lost. To verify that data has been received correctly in noisy environ- The watchdog timer is enabled, and the timeout period (5 ms, ments, the AD5755-1 offers the option of packet error checking 10 ms, 100 ms, or 200 ms) is set in the main control register (see based on an 8-bit cyclic redundancy check (CRC-8). The device Table 18 and Table 19). controlling the AD5755-1 should generate an 8-bit frame check OUTPUT ALERT sequence using the polynomial The AD5755-1 is equipped with an ALERT pin. This is an C(x) = x + x + x + 1 8 2 1 active high CMOS output. The AD5755-1 also has an internal This is added to the end of the data-word, and 32 bits are sent to watchdog timer. When enabled, it monitors SPI communica- the AD5755-1 before taking SYNC high. If the AD5755-1 sees a tions. If 0x195 is not received by the software register within the 32-bit frame, it performs the error check when SYNC goes high. timeout period, the ALERT pin goes active. If the check is valid, the data is written to the selected register. INTERNAL REFERENCE FAULT If the error check fails, the pin goes low and the PEC The AD5755-1 contains an integrated +5 V voltage reference error bit in the status register is set. After reading the status with initial accuracy of ±5 mV maximum and a temperature FAULT register, returns high (assuming there are no other drift coefficient of ±10 ppm maximum. The reference voltage faults), and the PEC error bit is cleared automatically. is buffered and externally available for use elsewhere within UPDATE ON SYNC HIGH the system. SYNC EXTERNAL CURRENT SETTING RESISTOR SCLK Referring to Figure 73, RSET is an internal sense resistor as part MSB LSB of the voltage-to-current conversion circuitry. The stability of D23 D0 the output current value over temperature is dependent on the SDIN 24-BIT DATA stability of the value of R . As a method of improving the SET 24-BIT DATA TRANSFER—NO ERROR CHECKING stability of the output current over temperature, an external 15 kΩ low drift resistor can be connected to the RSET_x pin of the AD5755-1 to be used instead of the internal resistor, R1. The UPDATE ON SYNC HIGH SYNC ONLY IF ERROR CHECK PASSED external resistor is selected via the DAC control register (see Table 20). SCLK Table 1 outlines the performance specifications of the AD5755-1 MSB LSB with both the internal R resistor and an external, 15 kΩ R SET SET D31 D8 D7 D0 resistor. Using an external R resistor allows for improved SET SDIN 24-BIT DATA 8-BIT CRC performance over the internal RSET resistor option. The external RSET resistor specification assumes an ideal resistor; the actual performance depends on the absolute value and temperature FAULT PIN GOES LOW FAULT IF ERROR CHECK FAILS coefficient of the resistor used. This directly affects the gain error 32-BIT DATA TRANSFER WITH ERROR CHECKING of the output, and thus the total unadjusted error. To arrive at Figure 78. PEC Timing the gain/TUE error of the output with a particular external R SET The PEC can be used for both transmit and receive of data resistor, add the percentage absolute error of the R resistor SET packets. If status readback during a write is enabled, the PEC directly to the gain/TUE error of the AD5755-1 with the exter- values returned during the status readback during a write nal RSET resistor, shown in Table 1 (expressed in % FSR). operation should be ignored. If status readback during a write is Rev. C | Page 41 of 52 09226-180 AD5755-1 Data Sheet Table 32. Slew Rate Update Clock Options HART 1 SR_CLOCK Update Clock Frequency (Hz) The AD5755-1 has four CHART pins, one corresponding to 0000 64 k each output channels. A HART signal can be coupled into these 0001 32 k pins. The HART signal appears on the corresponding current 0010 16 k output, if the output is enabled. Table 31 shows the recommended 0011 8 k input voltages for the HART signal at the CHART pin. If these 0100 4 k voltages are used, the current output should meet the HART 0101 2 k amplitude specifications. Figure 79 shows the recommended 0110 1 k circuit for attenuating and coupling in the HART signal. 0111 500 Table 31. CHART Input Voltage to HART Output Current 1000 250 CHART Input Current Output 1001 125 R Voltage (HART) SET 1010 64 Internal RSET 150 mV p-p 1 mA p-p 1011 32 External RSET 170 mV p-p 1 mA p-p 1100 16 1101 8 C1 CHARTx 1110 4 C2 HART MODEM 1111 0.5 OUTPUT 1 Figure 79. Coupling HART Signal These clock frequencies are divided down from the 13 MHz internal oscillator. See Table 1, Figure 69, and Figure 70. A minimum capacitance of C1 + C2 is required to ensure that Table 33. Slew Rate Step Size Options the 1.2 kHz and 2.2 kHz HART frequencies are not significantly SR_STEP Step Size (LSBs) attenuated at the output. The recommended values are C1 = 22 nF, C2 = 47 nF. 000 1 001 2 Digitally controlling the slew rate of the output is necessary to 010 4 meet the analog rate of change requirements for HART. 011 16 DIGITAL SLEW RATE CONTROL 100 32 The slew rate control feature of the AD5755-1 allows the user to 101 64 control the rate at which the output value changes. This feature 110 128 is available on both the current and voltage outputs. With the 111 256 slew rate control feature disabled, the output value changes at a The following equation describes the slew rate as a function of rate limited by the output drive circuitry and the attached load. the step size, the update clock frequency, and the LSB size: To reduce the slew rate, this can be achieved by enabling the Slew Time= slew rate control feature. With the feature enabled via the SREN bit of the slew rate control register (see Table 26), the output, Output Change instead of slewing directly between two values, steps digitally at Step Size×Update Clock Frequency× LSB Size a rate defined by two parameters accessible via the slew rate where: control register, as shown in Table 26. Slew Time is expressed in seconds. The parameters are SR_CLOCK and SR_STEP. SR_CLOCK Output Change is expressed in amps for I or volts for V . OUT_x OUT_x defines the rate at which the digital slew is updated, for When the slew rate control feature is enabled, all output changes example, if the selected update rate is 8 kHz, the output updates occur at the programmed slew rate (see the DC-to-DC Converter every 125 µs. In conjunction with this, SR_STEP defines by how Settling Time section for additional information). For example, much the output value changes at each update. Together, both if the CLEAR pin is asserted, the output slews to the clear value parameters define the rate of change of the output value. Table 32 at the programmed slew rate (assuming that the clear channel is and Table 33 outline the range of values for both the enabled to be cleared). If a number of channels are enabled for SR_CLOCK and SR_STEP parameters. slew, care must be taken when asserting the CLEAR pin. If one of the channels is slewing when CLEAR is asserted, other chan- nels may change directly to their clear values not under slew rate control. The update clock frequency for any given value is the same for all output ranges. The step size, however, varies across output ranges for a given value of step size because the LSB size is different for each output range. Rev. C | Page 42 of 52 09226-076 Data Sheet AD5755-1 output disabled, the converter regulates the V supply to POWER DISSIPATION CONTROL BOOST_x +15 V (±5%). In current output mode with the output disabled, The AD5755-1 contains integrated dynamic power control the converter regulates the V supply to 7.4 V (±5%). BOOST_x using a dc-to-dc boost converter circuit, allowing reductions in power consumption from standard designs when using the part Within a channel, the VOUT_x and IOUT_x stages share a common in current output mode. VBOOST_x supply so that the outputs of the IOUT_x and VOUT_x stages can be tied together. In standard current input module designs, the load resistor values can range from typically 50 Ω to 750 Ω. Output module DC-to-DC Converter Settling Time systems must source enough voltage to meet the compliance When in current output mode, the settling time for a step greater voltage requirement across the full range of load resistor values. than ~1 V (I × R ) is dominated by the settling time of the OUT LOAD For example, in a 4 mA to 20 mA loop when driving 20 mA, a dc-to-dc converter. The exception to this is when the required compliance voltage of >15 V is required. When driving 20 mA voltage at the IOUT_x pin plus the compliance voltage is below into a 50 Ω load, only 1 V compliance is required. 7.4 V (±5%). A typical plot of the output settling time can be found in Figure 49. This plot is for a 1 kΩ load. The settling time The AD5755-1 circuitry senses the output voltage and regulates for smaller loads is faster. The settling time for current steps less this voltage to meet compliance requirements plus a small than 24 mA is also faster. headroom voltage. The AD5755-1 is capable of driving up to 24 mA through a 1 kΩ load. DC-to-DC Converter V Functionality MAX DC-TO-DC CONVERTERS The maximum VBOOST_x voltage is set in the dc-to-dc control register (23 V, 24.5 V, 27 V, or 29.5 V; see Table 25). On reaching The AD5755-1 contains four independent dc-to-dc converters. this maximum voltage, the dc-to-dc converter is disabled, and These are used to provide dynamic control of the V supply BOOST the V voltage is allowed to decay by ~0.4 V. After the BOOST_x voltage for each channel (see Figure 73). Figure 80 shows the V voltage has decayed by ~0.4 V, the dc-to-dc converter BOOST_x discrete components needed for the dc-to-dc circuitry, and the is reenabled, and the voltage ramps up again to V , if still MAX following sections describe component selection and operation required. This operation is shown in Figure 81. of this circuitry. 29.6 L D R V 0mA TO 24mA RANGE, 24mA OUTPUT DCDC DCDC FILTER MAX AV V OUTPUT UNLOADED CC BOOST_X DC_DC BIT 29.5 10µH 10Ω C IN C C FILTER DCDC ≥10µF 0.1µF 4.7µF 29.4 SWx 29.3 Figure 80. DC-to-DC Circuit 29.2 Table 34. Recommended DC-to-DC Components 29.1 DC-DCMaxV = 11 (29.5V) Symbol Component Value Manufacturer DC-DCx BIT = 1 29.0 L XAL4040-103 10 µH Coilcraft® DCDC f = 410kHz SW 28.9 T = 25°C C GRM32ER71H475KA88L 4.7 µF Murata A DCDC 28.8 DDCDC PMEG3010BEA 0.38 VF NXP 28.7 It is recommended to place a 10 Ω, 100 nF low-pass RC filter DC-DCx BIT = 0 28.6 after C . This consumes a small amount of power but DCDC 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 reduces the amount of ripple on the V supply. BOOST_x TIME (ms) Figure 81. Operation on Reaching VMAX DC-to-DC Converter Operation As can be seen in Figure 81, the DC-DCx bit in the status register The on-board dc-to-dc converters use a constant frequency, asserts when the AD5755-1 is ramping to the VMAX value but peak current mode control scheme to step up an AV input of CC deasserts when the voltage is decaying to VMAX − ~0.4 V. 4.5 V to 5.5 V to drive the AD5755-1 output channel. These are designed to operate in discontinuous conduction mode (DCM) DC-to-DC Converter On-Board Switch with a duty cycle of <90% typical. Discontinuous conduction The AD5755-1 contains a 0.425 Ω internal switch. The switch mode refers to a mode of operation where the inductor current current is monitored on a pulse by pulse basis and is limited to goes to zero for an appreciable percentage of the switching 0.8 A peak current. cycle. The dc-to-dc converters are nonsynchronous; that is, they DC-to-DC Converter Switching Frequency and Phase require an external Schottky diode. The AD5755-1 dc-to-dc converter switching frequency can be DC-to-DC Converter Output Voltage selected from the dc-to-dc control register. The phasing of the When a channel current output is enabled, the converter regulates channels can also be adjusted so that the dc-to-dc converter can the VBOOST_x supply to 7.4 V (±5%) or (IOUT × RLOAD + Headroom), clock on different edges (see Table 25). For typical applications, whichever is greater (see Figure 53 for a plot of headroom a 410 kHz frequency is recommended. At light loads (low output supplied vs. output current). In voltage output mode with the Rev. C | Page 43 of 52 09226-077 V VOLTAGE (mV) BOOST_x 09226-183 AD5755-1 Data Sheet current and small load resistor), the dc-to-dc converter enters a component. For the AD5755-1, a low ESR tantalum or ceramic pulse-skipping mode to minimize switching power dissipation. capacitor of 10 µF is recommended for typical applications. Ceramic capacitors must be chosen carefully because they can DC-to-DC Converter Inductor Selection exhibit a large sensitivity to dc bias voltages and temperature. For typical 4 mA to 20 mA applications, a 10 µH inductor (such X5R or X7R dielectrics are preferred because these capacitors as the XAL4040-103 from Coilcraft), combined with a switch- remain stable over wider operating voltage and temperature ing frequency of 410 kHz, allows up to 24 mA to be driven into a ranges. Care must be taken if selecting a tantalum capacitor to load resistance of up to 1 kΩ with an AV supply of 4.5 V to CC ensure a low ESR value. 5.5 V. It is important to ensure that the inductor is able to AI SUPPLY REQUIREMENTS—STATIC CC handle the peak current without saturating, especially at the maximum ambient temperature. If the inductor enters into The dc-to-dc converter is designed to supply a VBOOST_x voltage of saturation mode, it results in a decrease in efficiency. The VBOOST = IOUT × RLOAD + Headroom (2) inductance value also drops during saturation and may result in See Figure 53 for a plot of headroom supplied vs. output the dc-to-dc converter circuit not being able to supply the voltage. This means that, for a fixed load and output voltage, required output power. the dc-to-dc converter output current can be calculated by DC-to-DC Converter External Schottky Selection the following formula: The AD5755-1 requires an external Schottky for correct Power Out I ×V OUT BOOST operation. Ensure that the Schottky is rated to handle the AI = = (3) CC Efficiency× AV η × AV CC V CC maximum reverse breakdown expected in operation and that BOOST the rectifier maximum junction temperature is not exceeded. where: The diode average current is approximately equal to the I LOAD I is the output current from I in amps. OUT OUT_x current. Diodes with larger forward voltage drops result in a η is the efficiency at V as a fraction (see Figure 55 V BOOST_x BOOST decrease in efficiency. and Figure 56). DC-to-DC Converter Compensation Capacitors AI SUPPLY REQUIREMENTS—SLEWING CC As the dc-to-dc converter operates in DCM, the uncompensated The AI current requirement while slewing is greater than in CC transfer function is essentially a single-pole transfer function. static operation because the output power increases to charge The pole frequency of the transfer function is determined by the output capacitance of the dc-to-dc converter. This transient the dc-to-dc converter’s output capacitance, input and output current can be quite large (see Figure 82), although the methods voltage, and output load. The AD5755-1 uses an external capacitor described in the Reducing AICC Current Requirements section in conjunction with an internal 150 kΩ resistor to compensate can reduce the requirements on the AVCC supply. If not enough the regulator loop. Alternatively, an external compensation resistor AICC current can be provided, the AVCC voltage drops. Due to can be used in series with the compensation capacitor, by setting this AV drop, the AI current required to slew increases CC CC the DC-DC Comp bit in the dc-to-dc control register. In this case, further. This means that the voltage at AV drops further (see CC a ~50 kΩ resistor is recommended. A description of the advantages Equation 3) and the V voltage, and thus the output voltage, BOOST_x of this can be found in the AI Supply Requirements—Slewing CC may never reach its intended value. Because this AV voltage is CC section. For typical applications, a 10 nF dc-to-dc compensation common to all channels, this may also affect other channels. capacitor is recommended. 0.8 DC-to-DC Converter Input and Output Capacitor 30 0.7 Selection 25 The output capacitor affects ripple voltage of the dc-to-dc 0.6 0mA TO 24mA RANGE converter and indirectly limits the maximum slew rate at which 1kΩ LOAD 20 0.5 f = 410kHz SW the channel output current can rise. The ripple voltage is caused INDUCTOR = 10µH (XAL4040-103) T = 25°C A by a combination of the capacitance and equivalent series 0.4 15 resistance (ESR) of the capacitor. For the AD5755-1, a ceramic 0.3 capacitor of 4.7 µF is recommended for typical applications. 10 Larger capacitors or paralleled capacitors improve the ripple at 0.2 AI the expense of reduced slew rate. Larger capacitors also impact CC 5 I 0.1 OUT V the AVCC supplies current requirements while slewing (see the BOOST 0 0 AICC Supply Requirements—Slewing section). This capacitance 0 0.5 1.0 1.5 2.0 2.5 at the output of the dc-to-dc converter should be >3 µF under TIME (ms) Figure 82. AI Current vs. Time for 24 mA Step Through 1 kΩ Load all operating conditions. CC with Internal Compensation Resistor The input capacitor provides much of the dynamic current required for the dc-to-dc converter and should be a low ESR Rev. C | Page 44 of 52 AI CURRENT (A) CC I CURRENT (mA)/V VOLTAGE (V) OUT_x BOOST_x 09226-184 Data Sheet AD5755-1 0.8 32 Reducing AI Current Requirements CC AI CC 0mA TO 24mA RANGE 0.7 I 28 There are two main methods that can be used to reduce the OUT 500Ω LOAD V BOOST f = 410kHz SW AICC current requirements. One method is to add an external 0.6 INDUCTOR = 10µH (XAL4040-103) 24 T = 25°C A compensation resistor, and the other is to use slew rate control. 0.5 20 Both of these methods can be used in conjunction. A compensation resistor can be placed at the COMP pin 0.4 16 DCDC_x in series with the 10 nF compensation capacitor. A 51 kΩ exter- 0.3 12 nal compensation resistor is recommended. This compensation increases the slew time of the current output but eases the AI 0.2 8 CC transient current requirements. Figure 83 shows a plot of AICC 0.1 4 current for a 24 mA step through a 1 kΩ load when using a 0 0 51 kΩ compensation resistor. This method eases the current 0 0.5 1.0 1.5 2.0 2.5 requirements through smaller loads even further, as shown in TIME (ms) Figure 84. Figure 84. AICC Current vs. Time for 24 mA Step Through 500 Ω Load with External 51 kΩ Compensation Resistor 0.8 32 0mA TO 24mA RANGE 1kΩ LOAD Using slew rate control can greatly reduce the AVCC supplies f = 410kHz 0.7 SW 28 INDUCTOR = 10µH (XAL4040-103) current requirements, as shown in Figure 85. When using slew T = 25°C A 0.6 24 rate control, attention should be paid to the fact that the output cannot slew faster than the dc-to-dc converter. The dc-to-dc 0.5 20 converter slews slowest at higher currents through large (for 0.4 16 example, 1 kΩ) loads. This slew rate is also dependent on the configuration of the dc-to-dc converter. Two examples of the 0.3 12 dc-to-dc converter output slew are shown in Figure 83 and 0.2 8 Figure 84 (VBOOST corresponds to the dc-to-dc converter’s output AI CC voltage). 0.1 I 4 OUT V BOOST 0.8 32 0 0 0mA TO 24mA RANGE 0 0.5 1.0 1.5 2.0 2.5 1kΩ LOAD 0.7 28 f = 410kHz TIME (ms) SW INDUCTOR = 10µH (XAL4040-103) T = 25°C Figure 83. AICC Current vs. Time for 24 mA Step Through 1 kΩ Load A 0.6 24 with External 51 kΩ Compensation Resistor AI CC 0.5 I 20 OUT V BOOST 0.4 16 0.3 12 0.2 8 0.1 4 0 0 0 1 2 3 4 5 6 TIME (ms) Figure 85. AICC Current vs. Time for 24 mA Step Through 1 kΩ Load with Slew Rate Control Rev. C | Page 45 of 52 AI CURRENT (A) CC I CURRENT (mA)/V VOLTAGE (V) OUT_x BOOST_x 09226-185 AI CURRENT (A) AI CURRENT (A) CC CC I CURRENT (mA)/V VOLTAGE (V) I CURRENT (mA)/V VOLTAGE (V) OUT_x BOOST_x OUT_x BOOST_x 09226-187 09226-186 AD5755-1 Data Sheet APPLICATIONS INFORMATION channels at zero scale, the full-scale error is 0.025%. Similarly, VOLTAGE AND CURRENT OUTPUT RANGES ON if only one channel is enabled in current output mode with the THE SAME TERMINAL internal RSET, the full-scale error is 0.025% FSR + 0.075% FSR = When using a channel of the AD5755-1, the current and voltage 0.1% FSR. output pins can be connected to two separate terminals or tied PRECISION VOLTAGE REFERENCE SELECTION together and connected to a single terminal. There is no conflict with tying the two output pins together because only the voltage To achieve the optimum performance from the AD5755-1 over output or the current output can be enabled at any one time. When its full operating temperature range, a precision voltage reference the current output is enabled, the voltage output is in tristate must be used. Thought should be given to the selection of a mode, and when the voltage output is enabled, the current precision voltage reference. The voltage applied to the reference output is in tristate mode. For this operation, the POC pin must inputs is used to provide a buffered reference for the DAC cores. be tied low and the POC bit in the main control register set to 0, Therefore, any error in the voltage reference is reflected in the or, if the POC pin is tied high, the POC bit in the main control outputs of the device. register must be set to 1 before the current output is enabled. There are four possible sources of error to consider when As shown in the Absolute Maximum Ratings section, the output choosing a voltage reference for high accuracy applications: tolerances are the same for both the voltage and current output initial accuracy, temperature coefficient of the output voltage, pins. The +V SENSE_x connections are buffered so that current long term drift, and output voltage noise. leakage into these pins is negligible when in current output mode. Initial accuracy error on the output voltage of an external refer- ence can lead to a full-scale error in the DAC. Therefore, to CURRENT OUTPUT MODE WITH INTERNAL R SET minimize these errors, a reference with low initial accuracy When using the internal R resistor in current output mode, SET error specification is preferred. Choosing a reference with an the output is significantly affected by how many other channels output trim adjustment, such as the ADR425, allows a system using the internal RSET are enabled and by the dc crosstalk from designer to trim system errors out by setting the reference these channels. The internal RSET specifications in Table 1 are voltage to a voltage other than the nominal. The trim adjust- for all channels enabled with the internal RSET selected and ment can be used at any temperature to trim out any error. outputting the same code. Long-term drift is a measure of how much the reference output For every channel enabled with the internal R , the offset error SET voltage drifts over time. A reference with a tight long-term drift decreases. For example, with one current output enabled using specification ensures that the overall solution remains relatively the internal R , the offset error is 0.075% FSR. This value SET stable over its entire lifetime. decreases proportionally as more current channels are enabled; the offset error is 0.056% FSR on each of two channels, 0.029% The temperature coefficient of a reference’s output voltage affects on each of three channels, and 0.01% on each of four channels. INL, DNL, and TUE. A reference with a tight temperature coefficient specification should be chosen to reduce the depend- Similarly, the dc crosstalk when using the internal RSET is propor- ence of the DAC output voltage to ambient temperature. tional to the number of current output channels enabled with the internal R . For example, with the measured channel at In high accuracy applications, which have a relatively low noise SET 0x8000 and one channel going from zero to full scale, the dc budget, reference output voltage noise must be considered. crosstalk is −0.011% FSR. With two channels going from zero to Choosing a reference with as low an output noise voltage as full scale, it is −0.019% FSR, and with all three other channels practical for the system resolution required is important. going from zero to full scale, it is −0.025% FSR. Precision voltage references such as the ADR435 (XFET design) produce low output noise in the 0.1 Hz to 10 Hz region. However, For the full-scale error measurement in Table 1, all channels are as the circuit bandwidth increases, filtering the output of the at 0xFFFF. This means that, as any channel goes to zero scale, reference may be required to minimize the output noise. the full-scale error increases due to the dc crosstalk. For example, with the measured channel at 0xFFFF and three Table 35. Recommended Precision References Initial Accuracy Long-Term Drift 0.1 Hz to 10 Hz Noise Part No. (mV Maximum) (ppm Typical) Temperature Drift (ppm/°C Maximum) (µV p-p Typical) ADR445 ±2 50 3 2.25 ADR02 ±3 50 3 10 ADR435 ±2 40 3 8 ADR395 ±5 50 9 8 AD586 ±2.5 15 10 4 Rev. C | Page 46 of 52 Data Sheet AD5755-1 DRIVING INDUCTIVE LOADS MICROPROCESSOR INTERFACING When driving inductive or poorly defined loads, a capacitor Microprocessor interfacing to the AD5755-1 is via a serial bus may be required between IOUT_x and AGND to ensure stability. that uses a protocol compatible with microcontrollers and DSP A 0.01 µF capacitor between I and AGND ensures stability processors. The communications channel is a 3-wire minimum OUT_x of a load of 50 mH. The capacitive component of the load may interface consisting of a clock signal, a data signal, and a latch cause slower settling, although this may be masked by the set- signal. The AD5755-1 requires a 24-bit data-word with data tling time of the AD5755-1. There is no maximum capacitance valid on the falling edge of SCLK. limit for the current output of the AD5755-1. The DAC output update is initiated on either the rising edge of LDAC or, if LDAC is held low, on the rising edge of SYNC. The TRANSIENT VOLTAGE PROTECTION contents of the registers can be read using the readback function. The AD5755-1 contains ESD protection diodes that prevent damage from normal handling. The industrial control AD5755-1-TO-ADSP-BF527 INTERFACE environment can, however, subject I/O circuits to much higher The AD5755-1 can be connected directly to the SPORT transients. To protect the AD5755-1 from excessively high interface of the ADSP-BF527, an Analog Devices, Inc., voltage transients, external power diodes and a surge current Blackfin® DSP. Figure 87 shows how the SPORT interface limiting resistor (RP) are required, as shown in Figure 86. A can be connected to control the AD5755-1. typical value for R is 10 Ω. The two protection diodes and the P AD5755-1 resistor (R ) must have appro-priate power ratings. P SPORT_TFS SYNC (FROM R SPORT_TSCK SCLK DC-TO-DC FILTER CONVERTER) SPORT_DTO SDIN 10Ω C C FILTER DCDC 4.7µF 0.1µF V ADSP-BF527 BOOST_x D1 GPIO0 LDAC AD5755-1 R P I OUT_x AGND Figure 87. AD5755-1-to-ADSP-BF527 SPORT Interface R D2 LOAD LAYOUT GUIDELINES Figure 86. Output Transient Voltage Protection Grounding Further protection can be provided using transient voltage In any circuit where accuracy is important, careful consideration suppressors (TVSs), also referred to as transorbs. These compo- of the power supply and ground return layout helps to ensure nents are available as unidirectional suppressors, which protect the rated performance. The printed circuit board on which the against positive high voltage transients, and as bidirectional AD5755-1 is mounted should be designed so that the analog suppressors, which protect against both positive and negative and digital sections are separated and confined to certain areas of high voltage transients. Transient voltage suppressors are avail- the board. If the AD5755-1 is in a system where multiple devices able in a wide range of standoff and breakdown voltage ratings. require an AGND-to-DGND connection, the connection should The TVS should be sized with the lowest breakdown voltage be made at one point only. The star ground point should be possible while not conducting in the functional range of the established as close as possible to the device. current output. The GNDSWx and ground connection for the AVCC supply are It is recommended that all field connected nodes be protected. referred to as PGND. PGND should be confined to certain areas The voltage output node can be protected with a similar circuit, of the board, and the PGND-to-AGND connection should be where D2 and the transorb are connected to AVSS. For the volt- made at one point only. age output node, the +VSENSE_x pin should also be protected with Supply Decoupling a large value series resistance to the transorb, such as 5 kΩ. In The AD5755-1 should have ample supply bypassing of 10 µF this way, the I and V pins can also be tied together and OUT_x OUT_x in parallel with 0.1 µF on each supply located as close to the share the same protection circuitry. package as possible, ideally right up against the device. The 10 µF capacitors are the tantalum bead type. The 0.1 µF capacitor should have low effective series resistance (ESR) and low effective series inductance (ESL), such as the common ceramic types, which provide a low impedance path to ground at high frequencies to handle transient currents due to internal logic switching. Rev. C | Page 47 of 52 09226-079 09226-080 AD5755-1 Data Sheet Traces GALVANICALLY ISOLATED INTERFACE The power supply lines of the AD5755-1 should use as large a In many process control applications, it is necessary to provide trace as possible to provide low impedance paths and reduce an isolation barrier between the controller and the unit being the effects of glitches on the power supply line. Fast switching controlled to protect and isolate the controlling circuitry from signals such as clocks should be shielded with digital ground any hazardous common-mode voltages that may occur. The to prevent radiating noise to other parts of the board and Analog Devices iCoupler® products can provide voltage isolation should never be run near the reference inputs. A ground line in excess of 2.5 kV. The serial loading structure of the AD5755- routed between the SDIN and SCLK lines helps reduce crosstalk 1 makes it ideal for isolated interfaces because the number of between them (not required on a multilayer board that has a interface lines is kept to a minimum. Figure 88 shows a 4- separate ground plane, but separating the lines helps). It is channel isolated interface to the AD5755-1 using an essential to minimize noise on the REFIN line because it ADuM1400. For more information, visit www.analog.com. couples through to the DAC output. MICROCONTROLLER ADuM1400* V V OA SERIAL CLOCK IA Avoid crossover of digital and analog signals. Traces on oppo- ENCODE DECODE TO SCLK OUT site sides of the board should run at right angles to each other. V V OB IB SERIAL DATA ENCODE DECODE TO SDIN This reduces the effects of feedthrough on the board. A OUT V microstrip technique is by far the best but not always possible V OC IC SYNC OUT ENCODE DECODE TO SYNC with a double-sided board. In this technique, the component V V ID OD CONTROL OUT ENCODE DECODE TO LDAC side of the board is dedicated to ground plane, whereas signal traces are placed on the solder side. *ADDITIONAL PINS OMITTED FOR CLARITY. Figure 88. Isolated Interface DC-to-DC Converters To achieve high efficiency, good regulation, and stability, a well- designed printed circuit board layout is required. Follow these guidelines when designing printed circuit boards (see Figure 80): • Keep the low ESR input capacitor, CIN, close to AVCC and PGND. • Keep the high current path from CIN through the inductor, LDCDC, to SWX and PGND as short as possible. • Keep the high current path from CIN through LDCDC and the rectifier, DDCDC, to the output capacitor, CDCDC, as short as possible. • Keep high current traces as short and as wide as possible. The path from C through the inductor, L , to SW and IN DCDC X PGND should be able to handle a minimum of 1 A. • Place the compensation components as close as possible to COMPDCDC_x. • Avoid routing high impedance traces near any node connected to SWx or near the inductor to prevent radiated noise injection. Rev. C | Page 48 of 52 09226-081 Data Sheet AD5755-1 CHARTx pin of the AD5755-1. Such a configuration results in INDUSTRIAL HART CAPABLE ANALOG OUTPUT the AD5700 HART modem output modulating the 4 mA to 20 APPLICATION—SHARED V AND I PIN OUT_X OUT_X mA analog current without affecting the dc level of the current. Many industrial control applications have requirements for This circuit adheres to the HART physical layer specifications as accurately controlled current output signals, and the AD5755-1 defined by the HART Communication Foundation. is ideal for such applications. Figure 89 shows the AD5755-1 in For transient overvoltage protection, a 24 V transient voltage a circuit design for a HART-enabled output module, specifically suppressor (TVS) is placed on the IOUT/VOUT connection. For for use in an industrial control application in which both the added protection, clamping diodes are connected from the voltage output and current output are available—one at a time—on I /V pin to the AV and AV power supply pins. A one pin, thus reducing the number of screw connections required. OUT_x OUT_x DD SS 5 kΩ current limiting resistor is also placed in series with the There is no conflict with tying the two output pins together +V input. This is to limit the current to an acceptable level because only the voltage output or the current output can be SENSE_x during a transient event. The recommended external band-pass enabled at any one time. filter for the AD5700 HART modem includes a 150 kΩ resistor, The design provides for a HART-enabled current output, with which limits current to a sufficiently low level to adhere to the HART capability provided by the AD5700/AD5700-1 HART intrinsic safety requirements. In this case, the input has higher modem, the industry’s lowest power and smallest footprint HART- transient voltage protection and should, therefore, not require compliant IC modem. For additional space-savings, the AD5700-1 additional protection circuitry, even in the most demanding of offers a 0.5% precision internal oscillator. The HART_OUT industrial environments. signal from the AD5700 is attenuated and ac-coupled into the +15V +15V 10µF 0.1µF 2.7V TO 5.5V AV AV SW (×4) V (×4) DD CC BOOST DV DD 10µF 10kΩ VOUT B, C, D 0.1µF RESET IOUT B, C, D ALERT D2 CHART B, C, D R FAULT P 4mA TO 20mA IOUT A CLEAR CURRENT LOOP D1 D3 SYNC AD5755-1 R L MCU 500Ω SCLK 5kΩ +VSENSE_A SDIN SDO AV SS UART INTERFACE VOUTA LDAC DGND –VSENSE_A AV REFOUT REFIN CHART A SS GND 0.1µF 47nF 22nF 0.1µF C2 C1 VCC TXD HART_OUT RXD RTS CD AD5700/AD5700-1 REF 1µF 1.2MΩ 300pF 150kΩ ADC_IP GND 1.2MΩ 150pF Figure 89. AD5755-1 in HART Configuration Rev. C | Page 49 of 52 09226-089 AD5755-1 Data Sheet OUTLINE DIMENSIONS 9.10 9.00 SQ 0.60 MAX 8.90 0.60 PIN 1 MAX INDICATOR 49 64 1 48 PIN 1 INDICATOR 8.85 0.50 EXPOSED 7.25 PAD 8.75 SQ BSC 7.10 SQ 8.65 6.95 0.50 16 33 0.40 32 17 0.30 0.25 MIN TOP VIEW BOTTOM VIEW 7.50 REF 0.80 MAX 12° MAX 1.00 0.65 TYP 0.85 0.05 MAX FOR PROPER CONNECTION OF 0.80 THE EXPOSED PAD, REFER TO 0.02 NOM THE PIN CONFIGURATION AND 0.30 FUNCTION DESCRIPTIONS SEATING 0.20 REF SECTION OF THIS DATA SHEET. PLANE 0.23 0.18 COMPLIANT TO JEDEC STANDARDS MO-220-VMMD-4 Figure 90. 64-Lead Lead Frame Chip Scale Package [LFCSP_VQ] 9 mm × 9 mm Body, Very Thin Quad (CP-64-3) Dimensions shown in millimeters ORDERING GUIDE 1 Model Resolution (Bits) Temperature Range Package Description Package Option AD5755-1ACPZ 16 −40°C to +105°C 64-lead LFCSP_VQ CP-64-3 AD5755-1ACPZ-REEL7 16 −40°C to +105°C 64-lead LFCSP_VQ CP-64-3 EVAL-AD5755-1SDZ Evaluation Board 1 Z = RoHS Compliant Part. Rev. C | Page 50 of 52 04-10-2012-C Data Sheet AD5755-1 NOTES Rev. C | Page 51 of 52 AD5755-1 Data Sheet NOTES ©2011–2012 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D09226-0-5/12(C) Rev. C | Page 52 of 52

Frequently asked questions

What makes Elite.Parts unique?

chervon down
At GID Industrial (Elite.Parts' parent company), we specialize in procuring industrial parts. We know where to find the rare and obsolete equipment that our customers need in order to get back to business. There are other companies who claim to do what we do, but we're confident that our commitment to quality and value is unparalleled in our field.

What kind of warranty will the AD5755-1 have?

chervon down
Warranties differ by part and by which suppliers we use to procure it for you. Sometimes, a part will be sold as-is and without a warranty. Our specialty, single board computers, tend to receive a one-year warranty.

Which carriers does Elite.Parts work with?

chervon down
Elite.Parts can ship via FedEx, UPS, DHL, and USPS. We have accounts with each of them and generally ship using one of those, but we can also ship using your account if you would prefer. However, we can use other carriers if it will be more convenient for you.

Will Elite.Parts sell to me even though I live outside the USA?

chervon down
Absolutely! We are happy to serve customers regardless of location. We work with international clients all the time, and we are familiar with shipping to destinations all across the globe.

I have a preferred payment method. Will Elite.Parts accept it?

chervon down
All major credit cards are accepted: Visa, MasterCard, Discover, and American Express. We will also accept payment made with wire transfer or PayPal. Checks will only be accepted from customers in the USA. Terms may available for larger orders, upon approval.

Why buy from GID?

quality

Quality

We are industry veterans who take pride in our work

protection

Protection

Avoid the dangers of risky trading in the gray market

access

Access

Our network of suppliers is ready and at your disposal

savings

Savings

Maintain legacy systems to prevent costly downtime

speed

Speed

Time is of the essence, and we are respectful of yours

What they say about us

FANTASTIC RESOURCE

star star star star star

One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!

Bucher Emhart Glass

EXCELLENT SERVICE

star star star star star

With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.

Fuji

HARD TO FIND A BETTER PROVIDER

star star star star star

Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.

Applied Materials

CONSISTENTLY DELIVERS QUALITY SOLUTIONS

star star star star star

Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.

Nidec Vamco

TERRIFIC RESOURCE

star star star star star

This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.

Trican Well Service

GO TO SOURCE

star star star star star

When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.

ConAgra Foods

Related Products

ANALOG DEVICE# A5E1032

SOCKET FOR MODEL AD210 IC

TRANSFORMER CURRENT 60.0 AMP

SOCKET FOR MODEL 1B22 IC

product

Analog Devices AD7291 12-Bit Low power 8-Channel Successive Approximation Analog-to-Digital Converte...