ANALOG DEVICES AD5752R
Description
Analog Devices AD5752R Complete, Dual, 16-Bit, Serial Input, Unipolar/Bipolar, Voltage Output Digital-to-Analog Converter
Part Number
AD5752R
Price
Request Quote
Manufacturer
ANALOG DEVICES
Lead Time
Request Quote
Category
PRODUCTS - A
Specifications
DAC Input Format
Ser,SPI
DAC Settling Time
7.5µs
DAC Type
Voltage Out
DAC Update Rate
1.07MSPS
Max Pos Supply (V)
+16.5V
Resolution (Bits)
16bit
Single-Supply
Yes
Features
- 24-lead TSSOP
- Asynchronous to zero scale or midscale CLR
- Complete, dual, 12-/14-/16-bit digital-to-analog converter (DAC)
- DSP-/micro-controller-compatible serial interface
- iCMOS process technology1
- INL error: ±16 LSB maximum, DNL error: ±1 LSB maximum
- Integrated reference buffers
- Integrated reference: 5 ppm/°C maximum
- Operates from single/dual supplies
- Operating temperature range: -40°C to +85°C
- Output control during power-up/brownout
- Settling time: 10 µs typical
- Simultaneous updating via LDAC
- Software programmable output range: +5 V, +10 V, +10.8 V, ±5 V, ±10 V, ±10.8 V
- Total unadjusted error (TUE): 0.1% FSR maximum
Datasheet
Extracted Text
Complete, Dual, 12-/14-/16-Bit, Serial Input, Unipolar/Bipolar, Voltage Output DACs AD5722R/AD5732R/AD5752R +10.8 V, ±5 V, ±10 V, or ±10.8 V. Integrated output amplifiers, FEATURES reference buffers, and proprietary power-up/power-down Complete, dual, 12-/14-/16-bit digital-to-analog converter (DAC) control circuitry are also provided. Operates from single/dual supplies Software programmable output range The parts offer guaranteed monotonicity, integral nonlinearity +5 V, +10 V, +10.8 V, ±5 V, ±10 V, ±10.8 V (INL) of ±16 LSB maximum, low noise, 10 μs maximum settling INL error: ±16 LSB maximum, DNL error: ±1 LSB maximum time, and an on-chip +2.5 V reference. Total unadjusted error (TUE): 0.1% FSR maximum The AD5722R/AD5732R/AD5752R use a serial interface that Settling time: 10 μs typical operates at clock rates up to 30 MHz and are compatible with Integrated reference: 5 ppm/°C maximum DSP and microcontroller interface standards. Double buffering Integrated reference buffers allows the simultaneous updating of all DACs. The input coding Output control during power-up/brownout is user-selectable twos complement or offset binary for a bipolar Simultaneous updating via LDAC 2sComp output (depending on the state of Pin BIN/ ), and Asynchronous CLR to zero scale or midscale straight binary for a unipolar output. The asynchronous clear DSP-/microcontroller-compatible serial interface function clears all DAC registers to a user-selectable zero-scale 24-lead TSSOP or midscale output. The parts are available in a 24-lead TSSOP Operating temperature range: −40°C to +85°C 1 and offer guaranteed specifications over the −40°C to +85°C iCMOS process technology industrial temperature range. APPLICATIONS Industrial automation Table 1. Pin Compatible Devices Closed-loop servo control, process control Part Number Description Automotive test and measurement AD5722/AD5732/AD5752 AD5722R/AD5732R/AD5752R Programmable logic controllers without internal reference. AD5724/AD5734/AD5754 Complete, quad, 12-/14-/16-bit, GENERAL DESCRIPTION serial input, unipolar/bipolar, The AD5722R/AD5732R/AD5752R are dual, 12-/14-/16-bit, voltage output DACs. serial input, voltage output digital-to-analog converters. They AD5724R/AD5734R/AD5754R AD5724/AD5734/AD5754 with operate from single supply voltages of +4.5 V up to +16.5 V or internal reference. dual supply voltages from ±4.5 V up to ±16.5 V. Nominal full- scale output range is software selectable from +5 V, +10 V, FUNCTIONAL BLOCK DIAGRAM AV AV SS DD REFIN/REFOUT AD5722R/AD5732R/AD5752R DV CC 2.5V REFERENCE REFERENCE BUFFERS CLR BIN/2sCOMP n n INPUT DAC DAC A SDIN V A REGISTER A REGISTER A OUT INPUT SHIFT REGISTER SCLK AND n CONTROL SYNC INPUT DAC LOGIC DAC B REGISTER B REGISTER B V B OUT SDO GND LDAC DAC_GND (2) SIG_GND (2) AD5722: n = 12-BIT AD5732: n = 14-BIT AD5752: n = 16-BIT Figure 1. 1 For analog systems designers within industrial/instrumentation equipment OEMs who need high performance ICs at higher voltage levels, iCMOS® is a technology platform that enables the development of analog ICs capable of 30 V and operating at ±15 V supplies while allowing dramatic reductions in power consumption and package size, as well as increased ac and dc performance. Rev. D Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. rights of third parties that may result from its use. Specifications subject to change without notice. No Tel: 781.329.4700 www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Fax: 781.461.3113 ©2008–2011 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. 06466-001 AD5722R/AD5732R/AD5752R TABLE OF CONTENTS Features .............................................................................................. 1 Transfer Function....................................................................... 22 Applications....................................................................................... 1 Input Shift Register .................................................................... 26 General Description ......................................................................... 1 DAC Register .............................................................................. 27 Functional Block Diagram .............................................................. 1 Output Range Select Register ................................................... 27 Revision History ............................................................................... 2 Control Register ......................................................................... 28 Specifications..................................................................................... 3 Power Control Register ............................................................. 28 AC Performance Characteristics ................................................ 5 Design Features............................................................................... 29 Timing Characteristics ................................................................ 6 Analog Output Control ............................................................. 29 Timing Diagrams.......................................................................... 7 Power-Down Mode.................................................................... 29 Absolute Maximum Ratings............................................................ 9 Overcurrent Protection ............................................................. 29 ESD Caution.................................................................................. 9 Thermal Shutdown .................................................................... 29 Pin Configuration and Function Descriptions........................... 10 Internal Reference ...................................................................... 29 Typical Performance Characteristics ........................................... 11 Applications Information .............................................................. 30 Terminology .................................................................................... 18 +5 V/±5 V Operation ................................................................ 30 Theory of Operation ...................................................................... 20 Layout Guidelines....................................................................... 30 Architecture................................................................................. 20 Galvanically Isolated Interface ................................................. 30 Serial Interface ............................................................................ 20 Microprocessor Interfacing....................................................... 30 Load DAC (LDAC)..................................................................... 22 Outline Dimensions....................................................................... 31 Ordering Guide .......................................................................... 31 Asynchronous Clear (CLR)....................................................... 22 Configuring the AD5722R/AD5732R/AD5752R .................. 22 REVISION HISTORY 7/11—Rev. C to Rev. D Changes to Table 4: t7, t8, t10 Limits......................................................6 3/11—Rev. B to Rev. C Changes to Configuring the AD5722R/AD5732R/ AD5752R Section ........................................................................... 22 8/10—Rev. A to Rev. B Changes to Table 28........................................................................ 28 4/10—Rev. 0 to Rev. A Changes to Junction Temperature, T max Parameter, Table 5 .. 9 J Changes to Exposed Paddle Description, Table 6...................... 10 11/08—Revision 0: Initial Version Rev. D | Page 2 of 32 AD5722R/AD5732R/AD5752R SPECIFICATIONS 1 1 AVDD = 4.5 V to 16.5 V; AVSS = −4.5 V to −16.5 V, or AVSS = 0 V; GND = 0 V; REFIN= 2.5 V external; DVCC = 2.7 V to 5.5 V; RLOAD = 2 kΩ; CLOAD = 200 pF; all specifications TMIN to TMAX unless otherwise noted. Table 2. Parameter Min Typ Max Unit Test Conditions/Comments ACCURACY Outputs unloaded Resolution AD5752R 16 Bits AD5732R 14 Bits AD5722R 12 Bits Total Unadjusted Error (TUE) −0.1 +0.1 % FSR 2 Integral Nonlinearity (INL) AD5752R −16 +16 LSB AD5732R −4 +4 LSB AD5722R −1 +1 LSB Differential Nonlinearity (DNL) −1 +1 LSB All models, guaranteed monotonic Bipolar Zero Error −6 +6 mV T = 25 C, error at other temperatures A obtained using bipolar zero TC 3 Bipolar Zero TC ±4 ppm FSR/°C Zero-Scale Error −6 +6 mV TA = 25°C, error at other temperatures obtained using zero-scale TC 3 Zero-Scale TC ±4 ppm FSR/°C Offset Error −6 +6 mV T = 25°C, error at other temperatures A obtained using offset error TC 3 Offset Error TC ±4 ppm FSR/°C Gain Error −0.025 +0.025 % FSR ±10 V range, TA = 25°C, error at other temperatures obtained using gain TC 3 Gain Error −0.065 0 % FSR +10 V and +5 V ranges, T = 25°C, error at other A temperatures obtained using gain TC 3 Gain Error 0 +0.08 % FSR ±5 V range, TA = 25°C, error at other temperatures obtained using gain TC 3 Gain TC ±4 ppm FSR/°C 3 DC Crosstalk 120 μV REFERENCE INPUT/OUTPUT 3 Reference Input Reference Input Voltage 2.5 V ±1% for specified performance DC Input Impedance 1 5 MΩ Input Current −2 ±0.5 +2 μA Reference Range +2 +3 V Reference Output Output Voltage +2.497 +2.501 V T = 25°C A 3 Reference TC −5 ±1.8 +5 ppm/°C 0°C to +85°C −10 ±2.2 +10 ppm/°C −40°C to +85°C 3 Output Noise (0.1 Hz to 10 Hz) 5 μV p-p 3 Noise Spectral Density 75 nV/√Hz 10 kHz 3 OUTPUT CHARACTERISTICS Output Voltage Range −10.8 +10.8 V AVDD/AVSS = ±11.7 V min, REFIN = 2.5 V −12 +12 V AVDD/AVSS = ±12.9 V min, REFIN = 3 V Headroom 0.5 0.9 V Output Voltage TC ±4 ppm FSR/°C Short-Circuit Current 20 mA Load 2 kΩ For specified performance Capacitive Load Stability 4000 pF DC Output Impedance 0.5 Ω Rev. D | Page 3 of 32 AD5722R/AD5732R/AD5752R Parameter Min Typ Max Unit Test Conditions/Comments 3 DIGITAL INPUTS DVCC = 2.7 V to 5.5 V, JEDEC compliant Input High Voltage, VIH 2 V Input Low Voltage, VIL 0.8 V Input Current ±1 μA Per pin Pin Capacitance 5 pF Per pin 3 DIGITAL OUTPUTS (SDO) Output Low Voltage, V 0.4 V DV = 5 V ± 10%, sinking 200 μA OL CC Output High Voltage, V DV − 1 V DV = 5 V ± 10%, sourcing 200 μA OH CC CC Output Low Voltage, VOL 0.4 V DVCC = 2.7 V to 3.6 V, sinking 200 μA Output High Voltage, VOH DVCC − 0.5 V DVCC = 2.7 V to 3.6 V, sourcing 200 μA High Impedance Leakage Current ±1 μA High Impedance Output 5 pF Capacitance POWER REQUIREMENTS AV 4.5 16.5 V DD AV −4.5 −16.5 V SS DV 2.7 5.5 V CC 3 Power Supply Sensitivity ∆VOUT/∆ΑVDD −65 dB AIDD 3.25 mA/channel Outputs unloaded 2.4 mA/channel AV = 0 V, outputs unloaded SS AI 2.5 mA/channel Outputs unloaded SS DICC 0.5 3 μA VIH = DVCC, VIL = GND Power Dissipation 190 mW ±16.5 V operation, outputs unloaded 79 mW +16.5 V operation, AVSS = 0 V, outputs unloaded Power-Down Currents AI 40 μA DD AI 40 μA SS DICC 300 nA 1 For specified performance, the headroom requirement is 0.9 V. 2 INL is the relative accuracy. It is measured from Code 512, Code 128, and Code 32 for the AD5752R, AD5732R, and AD5722R, respectively. 3 Guaranteed by characterization; not production tested. Rev. D | Page 4 of 32 AD5722R/AD5732R/AD5752R AC PERFORMANCE CHARACTERISTICS 1 AVDD = 4.5 V to 16.5 V; AVSS = −4.5 V to −16.5 V, or AVSS = 0 V; GND = 0 V; REFIN = 2.5 V external; DVCC = 2.7 V to 5.5 V; RLOAD = 2 kΩ; CLOAD = 200 pF; all specifications TMIN to TMAX unless otherwise noted. Table 3. B Version 2 Parameter Min Typ Max Unit Test Conditions/Comments DYNAMIC PERFORMANCE Output Voltage Settling Time 10 12 μs 20 V step to ±0.03% FSR 7.5 8.5 μs 10 V step to ±0.03% FSR 5 μs 512 LSB step settling (16-bit resolution) Slew Rate 3.5 V/μs Digital-to-Analog Glitch Energy 13 nV-sec Glitch Impulse Peak Amplitude 35 mV Digital Crosstalk 10 nV-sec DAC-to-DAC Crosstalk 10 nV-sec Digital Feedthrough 0.6 nV-sec Output Noise 0.1 Hz to 10 Hz Bandwidth 15 μV p-p 0x8000 DAC code 100 kHz Bandwidth 80 μV rms Output Noise Spectral Density 320 nV/√Hz Measured at 10 kHz, 0x8000 DAC code 1 For specified performance, the headroom requirement is 0.9 V. 2 Guaranteed by design and characterization; not production tested. Rev. D | Page 5 of 32 AD5722R/AD5732R/AD5752R TIMING CHARACTERISTICS AVDD = 4.5 V to 16.5 V; AVSS = −4.5 V to −16.5 V, or AVSS = 0 V; GND = 0 V; REFIN = 2.5 V external; DVCC = 2.7 V to 5.5 V; RLOAD = 2 kΩ; CLOAD = 200 pF; all specifications TMIN to TMAX, unless otherwise noted. Table 4. 1, 2, 3 Parameter Limit at tMIN, tMAX Unit Description t1 33 ns min SCLK cycle time t2 13 ns min SCLK high time t3 13 ns min SCLK low time t 13 ns min SYNC falling edge to SCLK falling edge setup time 4 t 13 ns min SCLK falling edge to SYNC rising edge 5 t 100 ns min 6 Minimum SYNC high time (write mode) t7 7 ns min Data setup time t8 2 ns min Data hold time t 20 ns min LDAC falling edge to SYNC falling edge 9 t 130 ns min SYNC rising edge to LDAC falling edge 10 t 20 ns min LDAC pulse width low 11 t12 10 μs typ DAC output settling time t13 20 ns min CLR pulse width low t14 2.5 μs max CLR pulse activation time 4 t 13 ns min SYNC rising edge to SCLK rising edge 15 4 5 t 40 ns max SCLK rising edge to SDO valid (C = 15 pF) 16 L SDO t 200 ns min high time (readback/daisy-chain mode) 17 Minimum SYNC 1 Guaranteed by characterization; not production tested. 2 All input signals are specified with tR = tF = 5 ns (10% to 90% of DVCC) and timed from a voltage level of 1.2 V. 3 See Figure 2, Figure 3, and Figure 4. 4 Daisy-chain and readback mode. 5 C = capacitive load on SDO output. L SDO Rev. D | Page 6 of 32 AD5722R/AD5732R/AD5752R TIMING DIAGRAMS t 1 SCLK 1 2 24 t t t 6 3 2 t t 5 4 SYNC t 8 t 7 SDIN DB23 DB0 t 11 t 9 t 10 LDAC t 12 V x OUT t 12 V x OUT t 13 CLR t 14 V x OUT Figure 2. Serial Interface Timing Diagram t 1 SCLK 24 48 t t t t 3 2 5 17 t 15 t 4 SYNC t 8 t 7 D32B D0B D32B D0B SDIN INPUT WORD FOR DAC N INPUT WORD FOR DAC N – 1 t 16 DB23 DB0 SDO t UNDEFINED INPUT WORD FOR DAC N 10 t 11 LDAC Figure 3. Daisy-Chain Timing Diagram Rev. D | Page 7 of 32 06466-002 06466-003 AD5722R/AD5732R/AD5752R SCLK 1 1 24 24 t 17 SYNC DB23 DB0 DB23 DB0 SDIN INPUT WORD SPECIFIES NOP CONDITION REGISTER TO BE READ DB23 DB0 DB23 DB0 SDO UNDEFINED SELECTED REGISTER DATA CLOCKED OUT Figure 4. Readback Timing Diagram Rev. D | Page 8 of 32 06466-004 AD5722R/AD5732R/AD5752R ABSOLUTE MAXIMUM RATINGS TA = 25°C unless otherwise noted. Transient currents of up to 100 mA do not cause SCR latch-up. Table 5. Stresses above those listed under Absolute Maximum Ratings Parameter Rating may cause permanent damage to the device. This is a stress AV to GND −0.3 V to +17 V DD rating only; functional operation of the device at these or any AVSS to GND +0.3 V to −17 V other conditions above those indicated in the operational DVCC to GND −0.3 V to +7 V section of this specification is not implied. Exposure to absolute Digital Inputs to GND −0.3 V to DVCC + 0.3 V or to maximum rating conditions for extended periods may affect 7 V (whichever is less) device reliability. Digital Outputs to GND −0.3 V to DV + 0.3 V or to CC 7 V (whichever is less) REFIN/REFOUT to GND −0.3 V to +5 V ESD CAUTION VOUTA or VOUTB to GND AVSS to AVDD DAC_GND to GND −0.3 V to +0.3 V SIG_GND to GND −0.3 V to +0.3 V Operating Temperature Range, T A Industrial −40°C to +85°C Storage Temperature Range −65°C to +150°C Junction Temperature, TJ max 150°C 24-Lead TSSOP Package θ Thermal Impedance 42°C/W JA θ Thermal Impedance 9°C/W JC Power Dissipation (TJ max − TA)/θJA Lead Temperature JEDEC industry standard Soldering J-STD-020 ESD (Human Body Model) 3.5 kV Rev. D | Page 9 of 32 AD5722R/AD5732R/AD5752R PIN CONFIGURATION AND FUNCTION DESCRIPTIONS AV 1 24 AV DD SS NC 2 23 V B OUT V A 3 22 NC OUT NC 4 21 SIG_GND 5 AD5722R/ 20 SIG_GND BIN/2sCOMP AD5732R/ NC 6 19 DAC_GND AD5752R SYNC 7 18 DAC_GND TOP VIEW SCLK 8 (Not to Scale) 17 REFIN/REFOUT SDIN 9 16 SDO LDAC 10 15 GND DV CLR 11 14 CC NC 12 13 NC NOTES 1. NC = NO CONNECT 2. IT IS RECOMMENDED THAT THE EXPOSED PAD BE THERMALLY CONNECTED TO A COPPER PLANE FOR ENHANCED THERMAL PERFORMANCE. Figure 5. Pin Configuration Table 6. Pin Function Descriptions Pin No. Mnemonic Description 1 AVSS Negative Analog Supply. Voltage ranges from −4.5 V to −16.5 V. This pin can be connected to 0 V if output ranges are unipolar. 2, 4, 6, 12, NC Do not connect to these pins. 13, 22 3 V A Analog Output Voltage of DAC A. The output amplifier is capable of directly driving a 2 kΩ, 4000 pF load. OUT 5 BIN/2sCOMP Determines the DAC coding for a bipolar output range. This pin should be hardwired to either DVCC or GND. When hardwired to DVCC, input coding is offset binary. When hardwired to GND, input coding is twos complement. (For unipolar output ranges, coding is always straight binary.) 7 SYNC Active Low Input. This is the frame synchronization signal for the serial interface. While SYNC is low, data is transferred on the falling edge of SCLK. Data is latched on the rising edge of SYNC. 8 SCLK Serial Clock Input. Data is clocked into the shift register on the falling edge of SCLK. This operates at clock speeds up to 30 MHz. 9 SDIN Serial Data Input. Data must be valid on the falling edge of SCLK. 10 LDAC Load DAC, Logic Input. This is used to update the DAC registers and, consequently, the analog output. When this pin is tied permanently low, the addressed DAC register is updated on the rising edge of SYNC. If LDAC is held high during the write cycle, the DAC input register is updated, but the output update is held off until the falling edge of LDAC. In this mode, all analog outputs can be updated simultaneously on the falling edge of LDAC. The LDAC pin should not be left unconnected. 11 CLR Active Low Input. Asserting this pin sets the DAC registers to zero-scale code or midscale code (user selectable). 14 DV Digital Supply. Voltage ranges from 2.7 V to 5.5 V. CC 15 GND Ground Reference. 16 SDO Serial Data Output. Used to clock data from the serial register in daisy-chain or readback mode. Data is clocked out on the rising edge of SCLK and is valid on the falling edge of SCLK. 17 REFIN/REFOUT External Reference Voltage Input and Internal Reference Voltage Output. Reference input range is 2 V to 3 V. REFIN = 2.5 V for specified performance. REFOUT = 2.5 V ± 2 mV. 18, 19 DAC_GND Ground Reference for the Four Digital-to-Analog Converters. 20, 21 SIG_GND Ground Reference for the Four Output Amplifiers. 23 V B Analog Output Voltage of DAC B. The output amplifier is capable of directly driving a 2 kΩ, 4000 pF load. OUT 24 AVDD Positive Analog Supply. Voltage ranges from 4.5 V to 16.5 V. Exposed This exposed paddle should be connected to the potential of the AVSS pin, or alternatively, it can be left electrically Paddle unconnected. It is recommended that the paddle be thermally connected to a copper plane for enhanced thermal performance. Rev. D | Page 10 of 32 06466-005 AD5722R/AD5732R/AD5752R TYPICAL PERFORMANCE CHARACTERISTICS 6 0.6 AV /AV = +12V/0V, RANGE = +10V DD SS AV /AV = ±12V, RANGE = ±10V DD SS AV /AV = ±6.5V, RANGE = ±5V DD SS 4 0.4 AV /AV = +6.5V/0V, RANGE = +5V DD SS 2 0.2 0 0 –2 –0.2 –4 –0.4 AV /AV = +12V/0V, RANGE = +10V DD SS –6 –0.6 AV /AV = ±12V, RANGE = ±10V DD SS AV /AV = ±6.5V, RANGE = ±5V DD SS AV /AV = +6.5V/0V, RANGE = +5V DD SS –8 –0.8 0 10,000 20,000 30,000 40,000 50,000 60,000 0 10,000 20,000 30,000 40,000 50,000 60,000 CODE CODE Figure 6. AD5752R Integral Nonlinearity Error vs. Code Figure 9. AD5752R Differential Nonlinearity Error vs. Code 1.5 0.15 AV /AV = +12V/0V, RANGE = +10V DD SS AV /AV = ±12V, RANGE = ±10V DD SS AV /AV = ±6.5V, RANGE = ±5V DD SS 1.0 0.10 AV /AV = +6.5V/0V, RANGE = +5V DD SS 0.5 0.05 0 0 –0.5 –0.05 –1.0 –0.10 AV /AV = +12V/0V, RANGE = +10V DD SS –1.5 –0.15 AV /AV = ±12V, RANGE = ±10V DD SS AV /AV = ±6.5V, RANGE = ±5V DD SS AV /AV = +6.5V/0V, RANGE = +5V DD SS –2.0 –0.20 0 2000 4000 6000 8000 10,000 12,000 14,000 16,000 0 2000 4000 6000 8000 10,000 12,000 14,000 16,000 CODE CODE Figure 10. AD5732R Differential Nonlinearity Error vs. Code Figure 7. AD5732R Integral Nonlinearity Error vs. Code 0.3 0.04 AV /AV = +12V/0V, RANGE = +10V AV /AV = +12V/0V, RANGE = +10V DD SS DD SS AV /AV = ±12V, RANGE = ±10V AV /AV = ±12V, RANGE = ±10V DD SS DD SS AV /AV = ±6.5V, RANGE = ±5V 0.03 AV /AV = ±6.5V, RANGE = ±5V DD SS 0.2 DD SS AV /AV = +6.5V/0V, RANGE = +5V AV /AV = +6.5V/0V, RANGE = +5V DD SS DD SS 0.02 0.1 0.01 0 0 –0.1 –0.01 –0.2 –0.02 –0.3 –0.03 –0.4 –0.04 –0.5 –0.05 0 500 1000 1500 2000 2500 3000 3500 4000 0 500 1000 1500 2000 2500 3000 3500 4000 CODE CODE Figure 8. AD5722R Integral Nonlinearity Error vs. Code Figure 11. AD5722R Differential Nonlinearity Error vs. Code Rev. D | Page 11 of 32 INL ERROR (LSB) INL ERROR (LSB) INL ERROR (LSB) 06466-013 06466-015 06466-014 DNL ERROR (LSB) DNL ERROR (LSB) DNL ERROR (LSB) 06466-016 06466-017 06466-018 AD5722R/AD5732R/AD5752R 8 1.0 BIPOLAR 10V MIN UNIPOLAR 10V MIN 0.8 6 BIPOLAR 10V MAX UNIPOLAR 10V MAX 0.6 4 0.4 MAX INL ±10V MAX INL ±5V 2 0.2 MIN INL ±10V MIN INL ±5V MAX INL +10V 0 0 MIN INL +10V MAX INL +5V –0.2 MIN INL +5V –2 –0.4 –4 –0.6 –6 –0.8 –8 –1.0 11.5 12.0 12.5 13.0 13.5 14.0 14.5 15.0 15.5 16.0 16.5 –40 –20 0 20 40 60 80 TEMPERATURE (°C) SUPPLY VOLTAGE (V) Figure 12. AD5752R Integral Nonlinearity Error vs. Temperature Figure 15. AD5752R Differential Nonlinearity Error vs. Supply Voltage 0.1 10 8 0 6 –0.1 MAX DNL ±10V 4 MAX DNL ±5V MIN DNL ±10V 2 MIN DNL ±5V –0.2 BIPOLAR 5V MIN MAX DNL +10V UNIPOLAR 5V MIN MIN DNL +10V 0 BIPOLAR 5V MAX MAX DNL +5V UNIPOLAR 5V MAX –0.3 MIN DNL +5V –2 –4 –0.4 –6 –0.5 –8 –0.6 –10 –40 –20 0 20 40 60 80 5.5 6.5 7.5 8.5 9.5 10.5 11.5 12.513.514.515.516.5 TEMPERATURE (°C) SUPPLY VOLTAGE (V) Figure 13. AD5752R Differential Nonlinearity Error vs. Temperature Figure 16. AD5752R Integral Nonlinearity Error vs. Supply Voltage 10 1.0 BIPOLAR 5V MIN UNIPOLAR 5V MIN 8 0.8 BIPOLAR 5V MAX UNIPOLAR 5V MAX 6 0.6 4 0.4 0.2 2 BIPOLAR 10V MIN UNIPOLAR 10V MIN 0 0 BIPOLAR 10V MAX UNIPOLAR 10V MAX –2 –0.2 –0.4 –4 –6 –0.6 –0.8 –8 –10 –1.0 11.5 12.0 12.5 13.0 13.5 14.0 14.5 15.0 15.5 16.0 16.5 5.5 6.5 7.5 8.5 9.5 10.5 11.5 12.5 13.5 14.5 15.5 16.5 SUPPLY VOLTAGE (V) SUPPLY VOLTAGE (V) Figure 14. AD5752R Integral Nonlinearity Error vs. Supply Voltage Figure 17. AD5752R Differential Nonlinearity Error vs. Supply Voltage Rev. D | Page 12 of 32 INL ERROR (LSB) DNL ERROR (LSB) INL ERROR (LSB) 06466-045 06466-044 06466-034 DNL ERROR (LSB) DNL ERROR (LSB) INL ERROR (LSB) 06466-033 06466-035 06466-032 AD5722R/AD5732R/AD5752R 0.8 0.02 0.6 0.01 0.4 ±5V RANGE BIPOLAR 10V MIN 0.2 0 UNIPOLAR 10V MIN BIPOLAR 10V MAX 0 UNIPOLAR 10V MAX –0.01 ±10V RANGE –0.2 –0.4 –0.02 –0.6 –0.03 –0.8 –0.04 –1.0 11.5 12.0 12.5 13.0 13.5 14.0 14.5 15.0 15.5 16.0 16.5 –40 –20 0 20 40 60 80 SUPPLY VOLTAGE (V) TEMPERATURE (°C) Figure 18. AD5752R Total Unadjusted Error vs. Supply Voltage Figure 21. Bipolar Zero-Scale Error vs. Temperature 0.04 0.06 ±5V 0.03 0.04 0.02 0.01 BIPOLAR 5V MIN 0.02 UNIPOLAR 5V MIN BIPOLAR 5V MAX 0 UNIPOLAR 5V MAX 0 ±10V –0.01 –0.02 –0.02 +10V –0.03 –0.04 –0.04 –0.05 –0.06 5.5 6.5 7.5 8.5 9.5 10.5 11.5 12.5 13.5 14.5 15.5 16.5 –40 –20 0 20 40 60 80 SUPPLY VOLTAGE (V) TEMPERATURE (°C) Figure 19. AD5752R Total Unadjusted Error vs. Supply Voltage Figure 22. Gain Error vs. Temperature 4 1000 900 +10V 3 800 700 2 600 1 500 ±10V 400 0 DV = 5V CC 300 –1 200 100 –2 DV = 3V CC 0 ±5V –3 –100 0123456 –40 –20 0 20 40 60 80 V (V) TEMPERATURE (°C) LOGIC Figure 20. Zero-Scale Error vs. Temperature Figure 23. Digital Current vs. Logic Input Voltage Rev. D | Page 13 of 32 TUE (%) TUE (%) ZERO-SCALE ERROR (mV) 06466-046 06466-037 06466-036 DI (µA) CC GAIN ERROR (% FSR) BIPOLAR ZERO-SCALE ERROR (mV) 06466-043 06466-048 06466-047 AD5722R/AD5732R/AD5752R 0.010 12 ±5V RANGE, CODE = 0xFFFF ±10V RANGE, CODE = 0xFFFF +10V RANGE, CODE = 0xFFFF +5V RANGE, CODE = 0xFFFF 0.005 10 ±5V RANGE, CODE = 0x0000 ±10V RANGE, CODE = 0x0000 0 8 –0.005 6 –0.010 4 –0.015 2 –0.020 0 –25 –20 –15 –10 –5 0 5 10 15 20 25 –3 –1 13579 11 OUTPUT CURRENT (mA) TIME (µs) Figure 24. Output Source and Sink Capability Figure 27. Full-Scale Settling Time, +10 V Range 6 15 5 10 4 5 3 0 2 –5 1 –10 0 –15 –3 –1 13579 11 –3 –1 13579 11 TIME (µs) TIME (µs) Figure 25. Full-Scale Settling Time, ±10 V Range Figure 28. Full-Scale Settling Time, +5 V Range 7 0.020 ±10V RANGE, 0x7FF±F TO 0x8000 ±10V RANGE, 0x8000 T ± O 0x7FFF ±5V RANGE, 0x7FFF ± TO 0x8000 5 0.015 ±5V RANGE, 0x8000 T ± O 0x7FFF +10V RANGE, 0x7FFF TO 0x8000 +10V RANGE, 0x8000 TO 0x7FFF 3 0.010 +5V RANGE, 0x7FFF TO 0x8000 +5V RANGE, 0x8000 TO 0x7FFF 1 0.005 –1 0 –3 –0.005 –5 –0.010 –7 –0.015 –3 –1 13579 11 –1 0 12345 TIME (µs) TIME (µs) Figure 26. Full-Scale Settling Time, ±5 V Range Figure 29. Digital-to-Analog Glitch Energy Rev. D | Page 14 of 32 OUTPUT VOLTAGE DELTA (V) OUTPUT VOLTAGE (V) OUTPUT VOLTAGE (V) 06466-023 06466-022 06466-040 OUTPUT VOLTAGE (V) OUTPUT VOLTAGE (V) OUTPUT VOLTAGE (V) 06466-025 06466-024 06466-039 AD5722R/AD5732R/AD5752R 1 2 RANGE = ±5V RANGE = +10V RANGE = +5V RANGE = ±10V 1 CH1 5µV M 5s LINE 73.8V CH1 5V CH2 500mV M 200µs CH1 2.9V Figure 30. Peak-to-Peak Noise, 0.1 Hz to 10 Hz Bandwidth Figure 33. REFOUT Turn-On Transient 1 1 RANGE = ±5V RANGE = +10V RANGE = +5V RANGE = ±10V CH1 100mV M 5s LINE 1.2V CH1 5µV M5s LINE 73.8V Figure 31. Peak-to-Peak Noise, 100 kHz Bandwidth Figure 34. REFOUT Output Noise (100 kHz Bandwidth) 0.10 AV /AV = ±16.5V DD SS AV = +16.5V, AVSS = 0V DD 0.08 0.06 0.04 1 0.02 0 –0.02 –0.04 –0.06 CH1 10mV M 5s LINE 1.2V –50 –30 –10 1030507090 TIME (µs) Figure 32. Output Glitch on Power-Up Figure 35. REFOUT Output Noise (0.1 Hz to 10 Hz Bandwidth) Rev. D | Page 15 of 32 OUTPUT VOLTAGE (V) 06466-027 06466-026 06466-041 06466-030 06466-029 06466-028 AD5722R/AD5732R/AD5752R 3.0 1.0 AV /AV = +12V/0V, RANGE = +10V DD SS AV /AV = ±12V, RANGE = ±10V DD SS 2.9 AV /AV = ±6.5V, RANGE = ±5V DD SS 0.5 AV /AV = +6.5V/0V, RANGE = +5V DD SS 2.8 0 2.7 2.6 –0.5 2.5 –1.0 2.4 2.3 –1.5 2.2 –2.0 2.1 2.0 –2.5 –0.18 –0.13 –0.08 –0.03 0.02 0.07 0.12 0.17 0 500 1000 1500 2000 2500 3000 3500 4000 LOAD CURRENT (mA) CODE Figure 36. REFOUT Voltage vs. Load Current Figure 39. AD5722R Total Unadjusted Error vs. Code 15 40 AV /AV = +12V/0V, RANGE = +10V DD SS AV /AV = ±12V, RANGE = ±10V DD SS 10 AV /AV = ±6.5V, RANGE = ±5V DD SS 35 AV /AV = +6.5V/0V, RANGE = +5V DD SS 5 30 0 25 –5 –10 20 –15 15 –20 10 –25 5 –30 –35 0 0 1000 2000 3000 4000 5000 6000 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 7.0 TEMPERATURE COEFFICIENT (ppm/°C) CODE Figure 40. Reference Output TC (−40°C to +85°C) Figure 37. AD5752R Total Unadjusted Error vs. Code 4 40 AV /AV = +12V/0V, RANGE = +10V DD SS AV /AV = ±12V, RANGE = ±10V DD SS AV /AV = ±6.5V, RANGE = ±5V DD SS 35 2 AV /AV = +6.5V/0V, RANGE = +5V DD SS 30 0 25 –2 20 –4 15 –6 10 –8 5 –10 0 0 2000 4000 6000 8000 10,000 12,000 14,000 16,000 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 TEMPERATURE COEFFICIENT (ppm/°C) CODE Figure 38. AD5732R Total Unadjusted Error vs. Code Figure 41. Reference Output TC (0°C to 85°C) Rev. D | Page 16 of 32 TUE (LSB) REF VOLTAGE (V) TUE (LSB) OUT 06466-019 06466-031 06466-020 TUE (LSB) POPULATION (%) POPULATION (%) 06466-052 06466-049 06466-021 AD5722R/AD5732R/AD5752R 2.50120 2.50120 20 DEVICES SHOWN 20 DEVICES SHOWN 2.50100 2.50100 2.50080 2.50080 2.50060 2.50060 2.50040 2.50040 2.50020 2.50020 2.50000 2.50000 2.49980 2.49980 –40 –20 020 40 60 80 0 10 2030 4050 60 70 80 TEMPERATURE (°C) TEMPERATURE (°C) Figure 42. Reference Output Voltage vs. Temperature (−40°C to+ 85°C) Figure 43. Reference Output Voltage vs. Temperature (0°C to 85°C) Rev. D | Page 17 of 32 REFERENCE OUTPUT VOLTAGE (V) 06466-051 REFERENCE OUTPUT VOLTAGE (V) 06466-050 AD5722R/AD5732R/AD5752R TERMINOLOGY Gain TC Relative Accuracy or Integral Nonlinearity (INL) Gain TC is a measure of the change in gain error with changes For the DAC, relative accuracy, or integral nonlinearity, is a in temperature. Gain TC is expressed in ppm FSR/°C. measure of the maximum deviation in LSBs from a straight line passing through the endpoints of the DAC transfer function. A Total Unadjusted Error (TUE) typical INL vs. code plot can be seen in Figure 6. Total unadjusted error is a measure of the output error taking all the various errors into account, namely, INL error, offset Differential Nonlinearity (DNL) error, gain error, and output drift over supplies, temperature, Differential nonlinearity is the difference between the measured and time. TUE is expressed in % FSR. change and the ideal 1 LSB change between any two adjacent codes. A specified differential nonlinearity of ±1 LSB maximum Power-On Glitch Energy ensures monotonicity. Therefore, the AD5722R/AD5732R/ Power-on glitch energy is the impulse injected into the analog AD5752R DACs are guaranteed monotonic by design. A typical output when the AD5722R/AD5732R/AD5752R power on. It is DNL vs. code plot can be seen in Figure 9. normally specified as the area of the glitch in nV-sec (see Figure 32). Monotonicity Digital-to-Analog Glitch Impulse A DAC is monotonic if the output either increases or remains Digital-to-analog glitch impulse is the impulse injected into the constant for increasing digital input code. The AD5722R/ analog output when the input code in the DAC register changes state but the output voltage remains constant. It is normally AD5732R/AD5752R are monotonic over the full operating temperature range. specified as the area of the glitch in nV-sec and is measured when the digital input code is changed by 1 LSB at the major Bipolar Zero Error carry transition (0x7FFF to 0x8000). See Figure 29. Bipolar zero error is the deviation of the analog output from the ideal half-scale output of 0 V when the DAC register is loaded Glitch Impulse Peak Amplitude with 0x8000 (straight binary coding) or 0x0000 (twos complement Glitch impulse peak amplitude is the peak amplitude of the coding). A plot of bipolar zero error vs. temperature can be seen impulse injected into the analog output when the input code in in Figure 21. the DAC register changes state. It is specified as the amplitude of the glitch in mV and is measured when the digital input code Bipolar Zero Temperature Change (TC) is changed by 1 LSB at the major carry transition (0x7FFF to Bipolar zero TC is a measure of the change in the bipolar zero 0x8000). See Figure 29. error with a change in temperature. It is expressed in ppm FSR/°C. Digital Feedthrough Zero-Scale Error or Negative Full-Scale Error Digital feedthrough is a measure of the impulse injected into Zero-scale error is the error in the DAC output voltage when the analog output of the DAC from the digital inputs of the 0x0000 (straight binary coding) or 0x8000 (twos complement DAC and is measured when the DAC output is not updated. It coding) is loaded to the DAC register. Ideally, the output voltage is specified in nV-sec and measured with a full-scale code should be negative full-scale − 1 LSB. A plot of zero-scale error change on the data bus. vs. temperature can be seen in Figure 20. Power Supply Sensitivity Zero-Scale TC Power supply sensitivity indicates how the output of the DAC is Zero-scale TC is a measure of the change in zero-scale error with a affected by changes in the power supply voltage. change in temperature. Zero-scale TC is expressed in ppm FSR/°C. DC Crosstalk Output Voltage Settling Time DC crosstalk is the dc change in the output level of one DAC in Output voltage settling time is the amount of time required for response to a change in the output of another DAC. It is measured the output to settle to a specified level for a full-scale input change. with a full-scale output change on one DAC while monitoring A plot of full-scale settling time can be seen in Figure 25. another DAC. It is expressed in LSBs. Slew Rate Digital Crosstalk The slew rate of a device is a limitation in the rate of change of the output voltage. The output slewing speed of a voltage output Digital crosstalk is a measure of the impulse injected into the DAC is usually limited by the slew rate of the amplifier used at analog output of one DAC from the digital inputs of another its output. Slew rate is measured from 10% to 90% of the output DAC and is measured when the DAC output is not updated. It signal and is given in V/μs. is specified in nV-sec and measured with a full-scale code change on the data bus. Gain Error Gain error is a measure of the span error of the DAC. It is the deviation of the DAC transfer characteristic from the ideal slope and is expressed in % FSR. A plot of gain error vs. temperature can be seen in Figure 22. Rev. D | Page 18 of 32 AD5722R/AD5732R/AD5752R DAC-to-DAC Crosstalk Voltage Reference TC DAC-to-DAC crosstalk is the glitch impulse transferred to the Voltage reference TC is a measure of the change in the refer output of one DAC due to a digital code change and a subsequent ence output voltage with a change in temperature. This value output change of another DAC. This includes both digital and is expressed in ppm/°C. analog crosstalk. It is measured by loading one of the DACs with a full-scale code change (all 1s to all 0s, and vice versa) with LDAC low and monitoring the output of another DAC. The energy of the glitch is expressed in nV-sec. Rev. D | Page 19 of 32 AD5722R/AD5732R/AD5752R THEORY OF OPERATION REFIN The AD5722R/AD5732R/AD5752R are dual, 12-/14-/16-bit, serial input, unipolar/bipolar, voltage output DACs. They R operate from unipolar supply voltages of +4.5 V to +16.5 V or bipolar supply voltages of ±4.5 V to ±16.5 V. In addition, the parts have software-selectable output ranges of +5 V, +10 V, R +10.8 V, ±5 V, ±10 V, and ±10.8 V. Data is written to the AD5722R/AD5732R/AD5752R in a 24-bit word format via a TO OUTPUT R 3-wire serial interface. The devices also offer an SDO pin to AMPLIFIER facilitate daisy chaining or readback. The AD5722R/AD5732R/AD5752R incorporate a power-on reset circuit to ensure that the DAC registers power up loaded with 0x0000. When powered on, the outputs are clamped to 0 V via a low impedance path. The parts also feature on-chip reference and reference buffers. R ARCHITECTURE R The DAC architecture consists of a string DAC followed by an output amplifier. Figure 44 shows a block diagram of the DAC architecture. The reference input is buffered before being Figure 45. Resistor String Structure applied to the DAC. Output Amplifiers REFIN The output amplifiers are capable of generating both unipolar and bipolar output voltages. They are capable of driving a load REF (+) of 2 kΩ in parallel with 4000 pF to GND. The source and sink RESISTOR DAC REGISTER V x OUT STRING capabilities of the output amplifiers can be seen in Figure 24. CONFIGURABLE REF (–) The slew rate is 4.5 V/μs with a full-scale settling time of 10 μs. OUTPUT AMPLIFIER Reference Buffers GND OUTPUT The AD5722R/AD5732R/AD5752R can operate with either an RANGE CONTROL external or internal reference. The reference input has an input Figure 44. DAC Architecture Block Diagram range of 2 V to 3 V, with 2.5 V for specified performance. This The resistor string structure is shown in Figure 45. It is a string input voltage is then buffered before it is applied to the DAC cores. of resistors, each of value R. The code loaded to the DAC register SERIAL INTERFACE determines the node on the string where the voltage is to be The AD5722R/AD5732R/AD5752R are controlled over a tapped off and fed into the output amplifier. The voltage is versatile 3-wire serial interface that operates at clock rates up to tapped off by closing one of the switches connecting the string 30 MHz. It is compatible with SPI, QSPI™, MICROWIRE™, and to the amplifier. Because it is a string of resistors, it is guaranteed DSP standards. monotonic. Input Shift Register The input shift register is 24 bits wide. Data is loaded into the device MSB first as a 24-bit word under the control of a serial clock input, SCLK. The input register consists of a read/write bit, three register select bits, three DAC address bits, and 16 data bits. The timing diagram for this operation is shown in Figure 2. Rev. D | Page 20 of 32 06466-006 06466-007 AD5722R/AD5732R/AD5752R Standalone Operation Daisy-Chain Operation The serial interface works with both a continuous and noncon- For systems that contain several devices, the SDO pin can be tinuous serial clock. A continuous SCLK source can be used used to daisy-chain several devices together. Daisy-chain mode only if SYNC is held low for the correct number of clock cycles. can be useful in system diagnostics and in reducing the number of serial interface lines. The first falling edge of SYNC starts the In gated clock mode, a burst clock containing the exact number SYNC write cycle. SCLK is continuously applied to the input shift of clock cycles must be used, and must be taken high SYNC after the final clock to latch the data. The first falling edge of register when is low. If more than 24 clock pulses are SYNC applied, the data ripples out of the shift register and appears on starts the write cycle. Exactly 24 falling clock edges must the SDO line. This data is clocked out on the rising edge of SYNC be applied to SCLK before is brought high again. If th SCLK and is valid on the falling edge. By connecting the SDO SYNC is brought high before the 24 falling SCLK edge, the of the first device to the SDIN input of the next device in the data written is invalid. If more than 24 falling SCLK edges are chain, a multidevice interface is constructed. Each device in the applied before SYNC is brought high, the input data is also system requires 24 clock pulses. Therefore, the total number of invalid. The input register addressed is updated on the rising clock cycles must equal 24 × N, where N is the total number of SYNC SYNC edge of . For another serial transfer to take place, AD5722R/AD5732R/AD5752R devices in the chain. When the must be brought low again. After the end of the serial data SYNC serial transfer to all devices is complete, is taken high. transfer, data is automatically transferred from the input shift This latches the input data in each device in the daisy chain and register to the addressed register. prevents any further data from being clocked into the input shift When the data has been transferred into the chosen register of register. The serial clock can be a continuous or gated clock. the addressed DAC, all DAC registers and outputs can be A continuous SCLK source can only be used if SYNC is held updated by taking LDAC low while SYNC is high. low for the correct number of clock cycles. In gated clock mode, AD5722R/ a burst clock containing the exact number of clock cycles must * AD5732R/ 68HC11 SYNC AD5752R* be used, and must be taken high after the final clock to SDIN MOSI latch the data. SCK SCLK Readback Operation PC7 SYNC Readback mode is invoked by setting the R/W bit = 1 in the write PC6 LDAC SDO operation to the serial input shift register. (If the SDO output is MISO disabled via the SDO disable bit in the control register, it is auto- matically enabled for the duration of the read operation, after SDIN W which it is disabled again). With R/ = 1, Bit A2 to Bit A0 in AD5722R/ AD5732R/ association with Bit REG2 to Bit REG0 select the register to be AD5752R* read. The remaining data bits in the write sequence are don’t SCLK care bits. During the next SPI write, the data appearing on the SYNC SDO output contains the data from the previously addressed LDAC register. For a read of a single register, the NOP command can SDO be used in clocking out the data from the selected register on SDO. The readback diagram in Figure 4 shows the readback sequence. For example, to read back the DAC register of SDIN AD5722R/ Channel A, the following sequence should be implemented: AD5732R/ AD5752R* 1. Write 0x800000 to the AD5722R/AD5732R/AD5752R SCLK input register. This configures the part for read mode with SYNC the DAC register of Channel A selected. Note that all the LDAC data bits, DB15 to DB0, are don’t care bits. SDO 2. Follow this with a second write, a NOP condition, 0x180000. During this write, the data from the register is clocked out * ADDITIONAL PINS OMITTED FOR CLARITY. on the SDO line. Figure 46. Daisy Chaining the AD5722R/AD5732R/AD5752R Rev. D | Page 21 of 32 06466-008 AD5722R/AD5732R/AD5752R LOAD DAC (LDAC) CONFIGURING THE AD5722R/AD5732R/AD5752R When the power supplies are applied to the AD5722R/AD5732R/ After data has been transferred into the input register of the AD5752R, the power-on reset circuit ensures that all registers DACs, there are two ways to update the DAC registers and DAC default to 0. This places all channels and the internal reference SYNC LDAC outputs. Depending on the status of both and , one in power-down mode. The DV should be brought high before CC of two update modes is selected: individual DAC updating or any of the interface lines are powered. If this is not done the first simultaneous updating of all DACs. write to the device may be ignored. The first communication to OUTPUT AMPLIFIER the AD5722R/AD5732R/AD5752R should be to set the required 12-/14-/16-BIT REFIN V x OUT output range on all channels (the default range is the 5 V unipolar DAC range) by writing to the output range select register. The user should then write to the power control register to power on the DAC LDAC REGISTER required channels and the internal reference, if required. If an external reference source is being used, the internal reference must remain in power-down mode. To program an INPUT REGISTER output value on a channel, that channel must first be powered up; any writes to a channel while it is in power-down mode are SCLK ignored. The AD5722R/AD5732R/AD5752R operate with a INTERFACE SDO SYNC LOGIC wide power supply range. It is important that the power supply SDIN applied to the parts provides adequate headroom to support the Figure 47. Simplified Diagram of Input Loading Circuitry for One DAC chosen output ranges. Individual DAC Updating TRANSFER FUNCTION LDAC In this mode, is held low while data is being clocked into Table 8 to Table 16 show the relationships of the ideal input code the input shift register. The addressed DAC output is updated to output voltage for the AD5752R, AD5732R, and AD5722R, on the rising edge of SYNC. respectively, for all output voltage ranges. For unipolar output Simultaneous Updating of All DACs ranges, the data coding is straight binary. For bipolar output LDAC 2sCOMP In this mode, is held high while data is being clocked ranges, the data coding is user selectable via the BIN/ into the input shift register. All DAC outputs are asynchronously pin and can be either offset binary or twos complement. LDAC SYNC updated by taking low after has been taken high. For a unipolar output range, the output voltage expression is LDAC The update now occurs on the falling edge of . given by ASYNCHRONOUS CLEAR (CLR) D ⎡ ⎤ V =V ×Gain OUT REFIN N ⎢ ⎥ CLR ⎣2 ⎦ is an active low clear that allows the outputs to be cleared to either zero-scale code or midscale code. The clear code value For a bipolar output range, the output voltage expression is given by is user selectable via the CLR select bit of the control register Gain×V D ⎡ ⎤ REFIN (see the Control Register section). It is necessary to maintain V =V ×Gain − OUT REFIN N ⎢ ⎥ ⎣2 ⎦ 2 CLR low for a minimum amount of time to complete the operation (see Figure 2). When the CLR signal is returned high, the output where: D is the decimal equivalent of the code loaded to the DAC. remains at the cleared value until a new value is programmed. The N is the bit resolution of the DAC. CLR outputs cannot be updated with a new value while the pin VREFIN is the reference voltage applied at the REFIN pin. is low. A clear operation can also be performed via the clear Gain is an internal gain whose value depends on the output command in the control register. range selected by the user, as shown in Table 7. Table 7. Output Range (V) Gain Value +5 2 +10 4 +10.8 4.32 ±5 4 ±10 8 ±10.8 8.64 Rev. D | Page 22 of 32 06466-009 AD5722R/AD5732R/AD5752R Ideal Output Voltage to Input Code Relationship—AD5752R Table 8. Bipolar Output, Offset Binary Coding Digital Input Analog Output MSB LSB ±5 V Output Range ±10 V Output Range ±10.8 V Output Range 1111 1111 1111 1111 +2 × REFIN × (32,767/32,768) +4 × REFIN × (32,767/32,768) +4.32 × REFIN × (32,767/32,768) 1111 1111 1111 1110 +2 × REFIN × (32,766/32,768) +4 × REFIN × (32,766/32,768) +4.32 × REFIN × (32,766/32,768) … … … … … … … 1000 0000 0000 0001 +2 × REFIN × (1/32,768) +4 × REFIN × (1/32,768) +4.32 × REFIN × (1/32,768) 1000 0000 0000 0000 0 V 0 V 0 V 0111 1111 1111 1111 −2 × REFIN × (1/32,768) −4 × REFIN × (1/32,768) −4.32 × REFIN × (32,766/32,768) … … … … … … … 0000 0000 0000 0001 −2 × REFIN × (32,766/32,768) −4 × REFIN × (32,766/32,768) −4.32 × REFIN × (32,766/32,768) 0000 0000 0000 0000 −2 × REFIN × (32,767/32,768 −4 × REFIN × (32,767/32,768) −4.32 × REFIN × (32,767/32,768) Table 9. Bipolar Output, Twos Complement Coding Digital Input Analog Output MSB LSB ±5 V Output Range ±10 V Output Range ±10.8 V Output Range 0111 1111 1111 1111 +2 × REFIN × (32,767/32,768) +4 × REFIN × (32,767/32,768) +4.32 × REFIN × (32,767/32,768) 0111 1111 1111 1110 +2 × REFIN × (32,766/32,768) +4 × REFIN × (32,766/32,768) +4.32 × REFIN × (32,766/32,768) … … … … … … … 0000 0000 0000 0001 +2 × REFIN × (1/32,768) +4 × REFIN × (1/32,768) +4.32 × REFIN × (1/32,768) 0000 0000 0000 0000 0 V 0 V 0 V 1111 1111 1111 1111 −2 × REFIN × (1/32,768) −4 × REFIN × (1/32,768) −4.32 × REFIN × (1/32,768) … … … … … … … 1000 0000 0000 0001 −2 × REFIN × (32,766/32,768) −4 × REFIN × (32,766/32,768) −4.32 × REFIN × (32,766/32,768) 1000 0000 0000 0000 −2 × REFIN × (32,767/32,768) −4 × REFIN × (32,767/32,768) −4.32 × REFIN × (32,767/32,768) Table 10. Unipolar Output, Straight Binary Coding Digital Input Analog Output MSB LSB +5 V Output Range +10 V Output Range +10.8 V Output Range 1111 1111 1111 1111 +2 × REFIN × (65,535/65,536) +4 × REFIN × (65,535/65,536) +4.32 × REFIN × (65,535/65,536) 1111 1111 1111 1110 +2 × REFIN × (65,534/65,536) +4 × REFIN × (65,534/65,536) +4.32 × REFIN × (65,534/65,536) … … … … … … … 1000 0000 0000 0001 +2 × REFIN × (32,769/65,536) +4 × REFIN × (32,769/65,536) +4.32 × REFIN × (32,769/65,536) 1000 0000 0000 0000 +2 × REFIN × (32,768/65,536) +4 × REFIN × (32,768/65,536) +4.32 × REFIN × (32,768/65,536) 0111 1111 1111 1111 +2 × REFIN × (32,767/65,536) +4 × REFIN × (32,767/65,536) +4.32 × REFIN × (32,767/65,536) … … … … … … … 0000 0000 0000 0001 +2 × REFIN × (1/65,536) +4 × REFIN × (1/65,536) +4.32 × REFIN × (1/65,536) 0000 0000 0000 0000 0 V 0 V 0 V Rev. D | Page 23 of 32 AD5722R/AD5732R/AD5752R Ideal Output Voltage to Input Code Relationship—AD5732R Table 11. Bipolar Output, Offset Binary Coding Digital Input Analog Output MSB LSB ±5 V Output Range ±10 V Output Range ±10.8 V Output Range 11 1111 1111 1111 +2 × REFIN × (8191/8192) +4 × REFIN × (8191/8192) +4.32 × REFIN × (8191/8192) 11 1111 1111 1110 +2 × REFIN × (8190/8192) +4 × REFIN × (8190/8192) +4.32 × REFIN × (8190/8192) … … … … … … … 10 0000 0000 0001 +2 × REFIN × (1/8192) +4 × REFIN × (1/8192) +4 × REFIN × (1/8192) 10 0000 0000 0000 0 V 0 V 0 V 01 1111 1111 1111 −2 × REFIN × (1/8192) −4 × REFIN × (1/8192) −4.32 × REFIN × (1/8192) … … … … … … … 00 0000 0000 0001 −2 × REFIN × (8190/8192) −4 × REFIN × (8190/8192) −4.32 × REFIN × (8190/8192) 00 0000 0000 0000 −2 × REFIN × (8191/8191) −4 × REFIN × (8191/8192) −4.32 × REFIN × (8191/8192) Table 12. Bipolar Output, Twos Complement Coding Digital Input Analog Output MSB LSB ±5 V Output Range ±10 V Output Range ±10.8 V Output Range 01 1111 1111 1111 +2 × REFIN × (8191/8192) +4 × REFIN × (8191/8192) +4.32 × REFIN × (8191/8192) 01 1111 1111 1110 +2 × REFIN × (8190/8192) +4 × REFIN × (8190/8192) +4.32 × REFIN × (8190/8192) … … … … … … … 00 0000 0000 0001 +2 × REFIN × (1/8192) +4 × REFIN × (1/8192) +4 × REFIN × (1/8192) 00 0000 0000 0000 0 V 0 V 0 V 11 1111 1111 1111 −2 × REFIN × (1/8192) −4 × REFIN × (1/8192) −4.32 × REFIN × (1/8192) … … … … … … … 10 0000 0000 0001 −2 × REFIN × (8190/8192) −4 × REFIN × (8190/8192) −4.32 × REFIN × (8190/8192) 10 0000 0000 0000 −2 × REFIN × (8191/8192) −4 × REFIN × (8191/8192) −4.32 × REFIN × (8191/8192) Table 13. Unipolar Output, Straight Binary Coding Digital Input Analog Output MSB LSB +5 V Output Range +10 V Output Range +10.8 V Output Range 11 1111 1111 1111 +2 × REFIN × (16,383/16,384) +4 × REFIN × (16,383/16,384) +4.32 × REFIN × (16,383/16,384) 11 1111 1111 1110 +2 × REFIN × (16,382/16,384) +4 × REFIN × (16,382/16,384) +4.32 × REFIN × (16,382/16,384) … … … … … … … 10 0000 0000 0001 +2 × REFIN × (8193/16,384) +4 × REFIN × (8193/16,384) +4.32 × REFIN × (8193/16,384) 10 0000 0000 0000 +2 × REFIN × (8192/16,384) +4 × REFIN × (8192/16,384) +4.32 × REFIN × (8192/16,384) 01 1111 1111 1111 +2 × REFIN × (8191/16,384) +4 × REFIN × (8191/16,384) +4.32 × REFIN × (8191/16,384) … … … … … … … 00 0000 0000 0001 +2 × REFIN × (1/16,384) +4 × REFIN × (1/16,384) +4.32 × REFIN × (1/16,384) 00 0000 0000 0000 0 V 0 V 0 V Rev. D | Page 24 of 32 AD5722R/AD5732R/AD5752R Ideal Output Voltage to Input Code Relationship—AD5722R Table 14. Bipolar Output, Offset Binary Coding Digital Input Analog Output MSB LSB ±5 V Output Range ±10 V Output Range ±10.8 V Output Range 1111 1111 1111 +2 × REFIN × (2047/2048) +4 × REFIN × (2047/2048) +4.32 × REFIN × (2047/2048) 1111 1111 1110 +2 × REFIN × (2046/2048) +4 × REFIN × (2046/2048) +4.32 × REFIN × (2046/2048) … … … … … … 1000 0000 0001 +2 × REFIN × (1/2048) +4 × REFIN × (1/2048) +4 × REFIN × (1/2048) 1000 0000 0000 0 V 0 V 0 V 0111 1111 1111 −2 × REFIN × (1/2048) −4 × REFIN × (1/2048) −4.32 × REFIN × (1/2048) … … … … … … 0000 0000 0001 −2 × REFIN × (2046/2048) −4 × REFIN × (2046/2048) −4.32 × REFIN × (2046/2048) 0000 0000 0000 −2 × REFIN × (2047/2047) −4 × REFIN × (2047/2048) −4.32 × REFIN × (2047/2048) Table 15. Bipolar Output, Twos Complement Coding Digital Input Analog Output MSB LSB ±5 V Output Range ±10 V Output Range ±10.8 V Output Range 0111 1111 1111 +2 × REFIN × (2047/2048) +4 × REFIN × (2047/2048) +4.32 × REFIN × (2047/2048) 0111 1111 1110 +2 × REFIN × (2046/2048) +4 × REFIN × (2046/2048) +4.32 × REFIN × (2046/2048) … … … … … … 0000 0000 0001 +2 × REFIN × (1/2048) +4 × REFIN × (1/2048) +4 × REFIN × (1/2048) 0000 0000 0000 0 V 0 V 0 V 1111 1111 1111 −2 × REFIN × (1/2048) −4 × REFIN × (1/2048) −4.32 × REFIN × (1/2048) … … … … … … 1000 0000 0001 −2 × REFIN × (2046/2048) −4 × REFIN × (2046/2048) −4.32 × REFIN × (2046/2048) 1000 0000 0000 −2 × REFIN × (2047/2048) −4 × REFIN × (2047/2048) −4.32 × REFIN × (2047/2048) Table 16. Unipolar Output, Straight Binary Coding Digital Input Analog Output MSB LSB +5 V Output Range +10 V Output Range +10.8 V Output Range 1111 1111 1111 +2 × REFIN × (4095/4096) +4 × REFIN × (4095/4096) +4.32 × REFIN × (4095/4096) 1111 1111 1110 +2 × REFIN × (4094/4096) +4 × REFIN × (4094/4096) +4.32 × REFIN × (4094/4096) … … … … … … 1000 0000 0001 +2 × REFIN × (2049/4096) +4 × REFIN × (2049/4096) +4.32 × REFIN × (2049/4096) 1000 0000 0000 +2 × REFIN × (2048/4096) +4 × REFIN × (2048/4096) +4.32 × REFIN × (2048/4096) 0111 1111 1111 +2 × REFIN × (2047/4096) +4 × REFIN × (2047/4096) +4.32 × REFIN × (2047/4096) … … … … … … 0000 0000 0001 +2 × REFIN × (1/4096) +4 × REFIN × (1/4096) 4.32 × REFIN × (1/4096) 0000 0000 0000 0 V 0 V 0 V Rev. D | Page 25 of 32 AD5722R/AD5732R/AD5752R INPUT SHIFT REGISTER The input shift register is 24 bits wide and consists of a read/write bit (R/W); a reserved bit (ZERO), which must always be set to 0; three register select bits (REG2, REG1, REG0); three DAC address bits (A2, A1, A0); and 16 data bits (data). The register data is clocked in MSB first on the SDIN pin. Table 17 shows the register format, while Table 18 describes the function of each bit in the register. All registers are read/write registers. Table 17. AD5752R Input Register Format MSB LSB DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 to DB0 R/W Zero REG2 REG1 REG0 A2 A1 A0 Data Table 18. Input Register Bit Functions Bit Mnemonic Description R/W Indicates a read from or a write to the addressed register. REG2, REG1, REG0 Used in association with the address bits to determine if a write operation is to the DAC register, output range select register, power control register, or control register. REG2 REG1 REG0 Function 0 0 0 DAC register 0 0 1 Output range select register 0 1 0 Power control register 0 1 1 Control register A2, A1, A0 These DAC address bits are used to decode the DAC channels. A2 A1 A0 Channel Address 0 0 0 DAC A 0 1 0 DAC B 1 0 0 Both DACs Data Data bits. Rev. D | Page 26 of 32 AD5722R/AD5732R/AD5752R DAC REGISTER The DAC register is addressed by setting the three REG bits to 000. The DAC address bits select the DAC channel where the data transfer is to take place (see Table 18). The data bits are in positions DB15 to DB0 for the AD5752R (see Table 19), DB15 to DB2 for the AD5732R (see Table 20), and DB15 to DB4 for the AD5722R (see Table 21). Table 19. Programming the AD5752R DAC Register MSB LSB R/W Zero REG2 REG1 REG0 A2 A1 A0 DB15 to DB0 0 0 0 0 0 DAC address 16-bit DAC data Table 20. Programming the AD5732R DAC Register MSB LSB R/W Zero REG2 REG1 REG0 A2 A1 A0 DB15 to DB2 DB1 DB0 0 0 0 0 0 DAC address 14-bit DAC data X X Table 21. Programming the AD5722R DAC Register MSB LSB R/W Zero REG2 REG1 REG0 A2 A1 A0 DB15 to DB4 DB3 DB2 DB1 DB0 0 0 0 0 0 DAC address 12-bit DAC data X X X X OUTPUT RANGE SELECT REGISTER The output range select register is addressed by setting the three REG bits to 001. The DAC address bits select the DAC channel, and the range bits (R2, R1, R0) select the required output range (see Table 22 and Table 23). Table 22. Programming the Required Output Range MSB LSB R/W Zero REG2 REG1 REG0 A2 A1 A0 DB15 to DB3 DB2 DB1 DB0 0 0 0 0 1 DAC address Don’t care R2 R1 R0 Table 23. Output Range Options R2 R1 R0 Output Range (V) 0 0 0 +5 0 0 1 +10 0 1 0 +10.8 0 1 1 ±5 1 0 0 ±10 1 0 1 ±10.8 Rev. D | Page 27 of 32 AD5722R/AD5732R/AD5752R CONTROL REGISTER The control register is addressed by setting the three REG bits to 011. The value written to the address and data bits determines the control function selected. The control register options are shown in Table 24 and Table 25. Table 24. Programming the Control Register MSB LSB R/W Zero REG2 REG1 REG0 A2 A1 A0 DB15 to DB4 DB3 DB2 DB1 DB0 0 0 0 1 1 0 0 0 NOP, data = don’t care 0 0 0 1 1 0 0 1 Don’t care TSD enable Clamp enable CLR select SDO disable 0 0 0 1 1 1 0 0 Clear, data = don’t care 0 0 0 1 1 1 0 1 Load, data = don’t care Table 25. Explanation of Control Register Options Option Description NOP No operation instruction used in readback operations. Clear Addressing this function sets the DAC registers to the clear code and updates the outputs. Load Addressing this function updates the DAC registers and, consequently, the DAC outputs. SDO Disable Set by the user to disable the SDO output. Cleared by the user to enable the SDO output (default). CLR Select See Table 26 for a description of the CLR select operation. Clamp Enable Set by the user to enable the current limit clamp. The channel does not power down upon detection of an overcurrent; the current is clamped at 20 mA (default). Cleared by the user to disable the current-limit clamp. The channel powers down upon detection of an overcurrent. TSD Enable Set by the user to enable the thermal shutdown feature. Cleared by the user to disable the thermal shutdown feature (default). Table 26. CLR Select Options Output CLR Value CLR Select Setting Unipolar Output Range Bipolar Output Range 0 0 V 0 V 1 Midscale Negative full scale POWER CONTROL REGISTER The power control register is addressed by setting the three REG bits to 010. This register allows the user to control and determine the power and thermal status of the AD5722R/AD5732R/AD5752R. The power control register options are shown in Table 27 and Table 28. Table 27. Programming the Power Control Register MSB LSB DB15 to R/W Zero REG2 REG1 REG0 A2 A1 A0 DB11 DB10 DB9 DB8 DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 0 0 0 1 0 0 0 0 X X OC X OC 0 TSD PU X PU X PU B A REF B A Table 28. Power Control Register Functions Option Description PU DAC A power-up. When set, this bit places DAC A in normal operating mode. When cleared, this bit places DAC A in power-down A mode (default). After setting this bit to power DAC A, a power-up time of 10 μs is required. During this power-up time the DAC register should not be loaded to the DAC output (see the Load DAC (LDAC) section). If the clamp enable bit of the control register is cleared, DAC A powers down automatically on detection of an overcurrent, and PUA is cleared to reflect this. PUB DAC B power-up. When set, this bit places DAC B in normal operating mode. When cleared, this bit places DAC B in power-down mode (default). After setting this bit to power DAC B, a power-up time of 10 μs is required. During this power-up time the DAC register should not be loaded to the DAC output (see the Load DAC (LDAC) section). If the clamp enable bit of the control register is cleared, DAC B powers down automatically on detection of an overcurrent, and PUB is cleared to reflect this. PUREF Reference power-up. When set, this bit places the internal reference in normal operating mode. When cleared, this bit places the internal reference in power-down mode (default). TSD Thermal shutdown alert. Read-only bit. In the event of an overtemperature situation, both DACs are powered down and this bit is set. OC DAC A overcurrent alert. Read-only bit. In the event of an overcurrent situation on DAC A, this bit is set. A OC DAC B overcurrent alert. Read-only bit. In the event of an overcurrent situation on DAC B, this bit is set. B Rev. D | Page 28 of 32 AD5722R/AD5732R/AD5752R DESIGN FEATURES Constant Current Clamp (Clamp Enable = 1) ANALOG OUTPUT CONTROL If a short circuit occurs in this configuration, the current is In many industrial process control applications, it is vital that clamped at 20 mA. This event is signaled to the user by the the output voltage be controlled during power-up. When the setting of the appropriate overcurrent (OC ) bit in the power X supply voltages change during power-up, the V pins are OUT control register. Upon removal of the short-circuit fault, the clamped to 0 V via a low impedance path (approximately 4 kΩ). OC bit is cleared. X To prevent the output amplifiers from being shorted to 0 V during this time, Transmission Gate G1 is also opened (see Automatic Channel Power-Down (Clamp Enable = 0) Figure 48). These conditions are maintained until the power If a short circuit occurs in this configuration, the shorted supplies have stabilized and a valid word is written to a DAC channel powers down, and its output is clamped to ground via a register. At this time, G2 opens and G1 closes. resistance of approximately 4 kΩ. At this time, the output of the amplifier is also disconnected from the output pin. The short- VOLTAGE MONITOR ) circuit event is signaled to the user via the overcurrent (OCX AND CONTROL bits, and the power-up (PUX) bits indicate which channels have G1 powered down. After the fault is rectified, the channels can be V A OUT powered up again by setting the PUX bits. G2 THERMAL SHUTDOWN The AD5722R/AD5732R/AD5752R incorporate a thermal shutdown feature that automatically shuts down the device if Figure 48. Analog Output Control Circuitry the core temperature exceeds approximately 150°C. The thermal POWER-DOWN MODE shutdown feature is disabled by default and can be enabled via Each DAC channel of the AD5722R/AD5732R/AD5752R can the TSD enable bit of the control register. In the event of a be individually powered down. By default, all channels are in thermal shutdown, the TSD bit of the power control register is set. power-down mode. The power status is controlled by the power INTERNAL REFERENCE control register (see Table 27 and Table 28 for details). When a The on-chip voltage reference is powered down by default. If an channel is in power-down mode, its output pin is clamped to external voltage reference source is to be used, the internal ground through a resistance of approximately 4 kΩ, and the reference must remain powered down at all times. If the output of the amplifier is disconnected from the output pin. internal reference is to be used as the reference source, it must OVERCURRENT PROTECTION be powered up via the PUREF bit of the power control register. Each DAC channel of the AD5722R/AD5732R/AD5752R The internal reference voltage is accessible at the REFIN/REFOUT incorporates individual overcurrent protection. The user has pin for use as a reference source for other devices within the two options for the configuration of the overcurrent protection: system. If the internal reference is to be used external to the constant current clamp or automatic channel power-down. The AD5722R/AD5732R/AD5752R, it must first be buffered. configuration of the overcurrent protection is selected via the clamp enable bit in the control register. Rev. D | Page 29 of 32 06466-010 AD5722R/AD5732R/AD5752R APPLICATIONS INFORMATION GALVANICALLY ISOLATED INTERFACE +5 V/±5 V OPERATION In many process control applications, it is necessary to provide When operating from a single +5 V supply or a dual ±5 V an isolation barrier between the controller and the unit being supply, an output range of +5 V or ±5 V is not achievable controlled to protect and isolate the controlling circuitry from because sufficient headroom for the output amplifier is not any hazardous common-mode voltages that may occur. The available. In this situation, a reduced reference voltage can be iCoupler® family of products from Analog Devices, Inc., provides used. For example, a 2 V reference voltage produces an output voltage isolation in excess of 2.5 kV. The serial loading structure range of +4 V or ±4 V, and the 1 V of headroom is more than of the AD5722R/AD5732R/AD5752R makes them ideal for enough for full operation. A standard value voltage reference isolated interfaces because the number of interface lines is kept of 2.048 V can be used to produce output ranges of +4.096 V to a minimum. Figure 49 shows a 4-channel isolated interface to and ±4.096 V. Refer to the plots in the Typical Performance the AD5722R/AD5732R/AD5752R using an ADuM1400. For Characteristics section for performance data at a range of more information, visit http://www.analog.com/icouplers. voltage reference values. MICROCONTROLLER ADuM1400* LAYOUT GUIDELINES V V IA OA SERIAL CLOCK OUT ENCODE DECODE TO SCLK In any circuit where accuracy is important, careful considera- V V IB OB SERIAL DATA OUT ENCODE DECODE TO SDIN tion of the power supply and ground return layout helps to V V IC OC ensure the rated performance. The printed circuit board on SYNC OUT ENCODE DECODE TO SYNC which the AD5722R/AD5732R/AD5752R are mounted should V V ID OD CONTROL OUT ENCODE DECODE TO LDAC be designed so that the analog and digital sections are separated and confined to certain areas of the board. If the AD5722R/ *ADDITIONAL PINS OMITTED FOR CLARITY. AD5732R/AD5752R are in a system where multiple devices Figure 49. Isolated Interface require an AGND-to-DGND connection, the connection should MICROPROCESSOR INTERFACING be made at one point only. The star ground point should be Microprocessor interfacing to the AD5722R/AD5732R/AD5752R established as close as possible to the device. is via a serial bus that uses standard protocol compatible with The AD5722R/AD5732R/AD5752R should have ample supply microcontrollers and DSP processors. The communications bypassing of a 10 μF capacitor in parallel with a 0.1 μF capacitor channel is a 3-wire (minimum) interface consisting of a clock on each supply located as close to the package as possible, signal, a data signal, and a synchronization signal. Each AD5722R/ ideally right up against the device. The 10 μF capacitors are the AD5732R/AD5752R requires a 24-bit data-word with data valid tantalum bead type. The 0.1 μF capacitor should have low on the falling edge of SCLK. effective series resistance (ESR) and low effective series For all interfaces, the DAC output update can be initiated inductance (ESI), such as the common ceramic types, which automatically when all the data is clocked in, or it can be provide a low impedance path to ground at high frequencies to performed under the control of LDAC. The contents of the handle transient currents due to internal logic switching. registers can be read using the readback function. The power supply lines of the AD5722R/AD5732R/AD5752R AD5722R/AD5732R/AD5752R to Blackfin® DSP Interface should use as large a trace as possible to provide low impedance paths and reduce the effects of glitches on the power supply line. Figure 50 shows how the AD5722R/AD5732R/AD5752R can be Fast switching signals, such as clock signals, should be shielded interfaced to Analog Devices Blackfin DSP. The Blackfin has an with digital ground to avoid radiating noise to other parts of the integrated SPI port that can be connected directly to the SPI pins board, and they should never be run near the reference inputs. of the AD5722R/AD5732R/AD5752R and the programmable I/O A ground line routed between the SDIN and SCLK lines helps pins that can be used to set the state of a digital input, such as reduce crosstalk between these lines (this is not required on a LDAC the pin. multilayer board that has a separate ground plane, but separating the lines does help). It is essential to minimize noise on the SPISELx SYNC SCK SCLK REFIN line because noise couples through to the DAC output. MOSI SDIN Avoid crossover of digital and analog signals. Traces on opposite AD5722R/ sides of the board should run at right angles to each other. This ADSP-BF531 AD5732R/ AD5752R reduces the effects of feedthrough on the board. A microstrip technique is by far the best method, but it is not always possible PF10 LDAC with a double-sided board. In this technique, the component side of the board is dedicated to a ground plane, and signal traces are placed on the solder side. Figure 50. AD5722R/AD5732R/AD5752R-to-Blackfin Interface Rev. D | Page 30 of 32 06466-012 06466-011 AD5722R/AD5732R/AD5752R OUTLINE DIMENSIONS 5.02 7.90 5.00 7.80 4.95 7.70 24 13 4.50 3.25 EXPOSED PAD 4.40 3.20 (Pins Up) 4.30 3.15 6.40 BSC 1 12 TOP VIEW BOTTOM VIEW FOR PROPER CONNECTION OF THE EXPOSED PAD, REFER TO 1.05 1.20 MAX THE PIN CONFIGURATION AND 1.00 8° FUNCTION DESCRIPTIONS 0.80 SECTION OF THIS DATA SHEET. 0° 0.20 0.15 0.30 0.65 0.75 SEATING 0.09 0.05 BSC 0.19 PLANE 0.60 0.10 COPLANARITY 0.45 COMPLIANT TO JEDEC STANDARDS MO-153-ADT Figure 51. 24-Lead Thin Shrink Small Outline Package, Exposed Pad [TSSOP_EP] (RE-24) Dimensions shown in millimeters ORDERING GUIDE 1 Model Resolution Temperature Range INL Package Description Package Option AD5722RBREZ 12 −40°C to 85°C ±1 LSB 24-Lead TSSOP_EP RE-24 AD5722RBREZ-REEL7 12 −40°C to 85°C ±1 LSB 24-Lead TSSOP_EP RE-24 AD5732RBREZ 14 −40°C to 85°C ±4 LSB 24-Lead TSSOP_EP RE-24 AD5732RBREZ-REEL7 14 −40°C to 85°C ±4 LSB 24-Lead TSSOP_EP RE-24 AD5752RBREZ 16 −40°C to 85°C ±16 LSB 24-Lead TSSOP_EP RE-24 AD5752RBREZ-REEL7 16 −40°C to 85°C ±16 LSB 24-Lead TSSOP_EP RE-24 1 Z = RoHS Compliant Part. Rev. D | Page 31 of 32 061708-A AD5722R/AD5732R/AD5752R NOTES ©2008–2011 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D06466-0-7/11(D) Rev. D | Page 32 of 32
Frequently asked questions
What makes Elite.Parts unique?
What kind of warranty will the AD5752R have?
Which carriers does Elite.Parts work with?
Will Elite.Parts sell to me even though I live outside the USA?
I have a preferred payment method. Will Elite.Parts accept it?
Why buy from GID?
Quality
We are industry veterans who take pride in our work
Protection
Avoid the dangers of risky trading in the gray market
Access
Our network of suppliers is ready and at your disposal
Savings
Maintain legacy systems to prevent costly downtime
Speed
Time is of the essence, and we are respectful of yours
Manufacturers


What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods