ANALOG DEVICES AD5751
Description
Analog Devices AD5751 Single-Channel, Low Cost, Precision, Voltage/Current Output Driver
Part Number
AD5751
Price
Request Quote
Manufacturer
ANALOG DEVICES
Lead Time
Request Quote
Category
PRODUCTS - A
Specifications
Vcc-Vee
10.8V to 55V
Features
- 32-lead 5 mm × 5 mm LFCSP package
- Asynchronous CLEAR function
- AVDD: 12 V (± 10%) to 55 V (maximum)
- Current output ranges: 0 mA to 20 mA, 0 mA to 24 mA, or 4 mA to 20 mA; ±0.03% FSR typical total unadjusted error (TUE); ±5 ppm/°C typical output drift; 2% over-range
- Flexible serial digital interface
- On-chip output fault detection
- Output loop compliance to AVDD - 2.75 V
- Over-range capability on all ranges
- PEC error checking
- Power supply range
- Temperature range: -40°C to +105°C
- Voltage output ranges: 0 V to 5 V, 0 V to 10 V, 0 V to 40 V; ±0.02% FSR typical total unadjusted error (TUE); ±3 ppm/°C typical output drift
Datasheet
Extracted Text
Industrial I/V Output Driver, Single-Supply, 55 V Maximum Supply, Programmable Ranges AD5751 FEATURES GENERAL DESCRIPTION Current output ranges: 0 mA to 20 mA, 0 mA to 24 mA, The AD5751 is a single-channel, low cost, precision, voltage/ or 4 mA to 20 mA current output driver with hardware or software programmable ±0.03% FSR typical total unadjusted error (TUE) output ranges. The software ranges are configured via an SPI-/ ±5 ppm/°C typical output drift MICROWIRE™-compatible serial interface. The AD5751 targets 2% overrange applications in PLC and industrial process control. The analog Voltage output ranges: 0 V to 5 V, 0 V to 10 V, 0 V to 40 V input to the AD5751 is provided from a low voltage, single-supply ±0.02% FSR typical total unadjusted error (TUE) digital-to-analog converter (DAC) and is internally conditioned ±3 ppm/°C typical output drift to provide the desired output current/voltage range. Overrange capability on all ranges The output current range is programmable across three current Flexible serial digital interface ranges: 0 mA to 20 mA, 0 mA to 24 mA, or 4 mA to 20 mA. On-chip output fault detection Voltage output is provided from a separate pin that can be PEC error checking configured to provide 0 V to 5 V, 0 V to 10 V, and 0 V to 40 V Asynchronous CLEAR function output ranges. An overrange is available on the voltage ranges. Power supply range AV : 12 V (± 10%) to 55 V (maximum) DD Analog outputs are short-circuit and open-circuit protected and Output loop compliance to AV − 2.75 V DD can drive capacitive loads of 1 μF and inductive loads of 0.1 H. Temperature range: −40°C to +105°C The device is specified to operate with a power supply range from 32-lead 5 mm × 5 mm LFCSP package 10.8 V to 55 V. Output loop compliance is 0 V to AV − 2.75 V. DD APPLICATIONS The flexible serial interface is SPI and MICROWIRE compatible Process control and can be operated in 3-wire mode to minimize the digital Actuator control isolation required in isolated applications. The interface also PLCs features an optional PEC error checking feature using CRC-8 error checking, useful in industrial environments where data communication corruption can occur. The device also includes a power-on reset function ensuring that the device powers up in a known state (0 V or tristate) and an asynchronous CLEAR pin that sets the outputs to zero- scale/midscale voltage output or the low end of the selected current range. An HW SELECT pin is used to configure the part for hardware or software mode on power-up. Table 1. Related Device Part Number Description AD5422 Single-channel, 16-bit, serial input current source and voltage output DAC Rev. A Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. rights of third parties that may result from its use. Specifications subject to change without notice. No Tel: 781.329.4700 www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. Fax: 781.461.3113 ©2009-2010 Analog Devices, Inc. All rights reserved. AD5751 TABLE OF CONTENTS Features .............................................................................................. 1 OUTEN ........................................................................................ 24 Applications ....................................................................................... 1 Software Control ........................................................................ 24 General Description ......................................................................... 1 Hardware Control ...................................................................... 26 Revision History ............................................................................... 2 Transfer Function ....................................................................... 26 Functional Block Diagram .............................................................. 3 Detailed Description of Features .................................................. 27 Specif ica t ions ..................................................................................... 4 Output Fault Alert—Software Mode ....................................... 27 Timing Characteristics ................................................................ 7 Output Fault Alert—Hardware Mode ..................................... 27 Absolute Maximum Ratings ............................................................ 9 Voltage Output Short-Circuit Protection ................................ 27 ESD Caution .................................................................................. 9 Asynchronous Clear (CLEAR) ................................................. 27 Pin Configuration and Function Descriptions ........................... 10 External Current Setting Resistor ............................................ 27 Typical Performance Characteristics ........................................... 12 Programmable Overrange Modes ............................................ 28 Current Output ........................................................................... 15 Packet Error Checking ............................................................... 28 Terminology .................................................................................... 20 Applications Information .............................................................. 29 Theory of Operation ...................................................................... 21 Transient Voltage Protection .................................................... 29 Software Mode ............................................................................ 21 Thermal Considerations ............................................................ 29 Currrent Output Architecture .................................................. 23 Layout Guidelines....................................................................... 30 Driving Inductive Loads ............................................................ 23 Galvanically Isolated Interface ................................................. 30 Power-On State of the AD5751 ................................................ 23 Microprocessor Interfacing ....................................................... 30 Default Registers at Power-On ................................................. 24 Outline Dimensions ....................................................................... 31 Reset Function ............................................................................ 24 Ordering Guide .......................................................................... 31 REVISION HISTORY 5/10—Rev. 0 to Rev. A Changes to Table 2, Power Requirements ..................................... 6 10/09—Revision 0: Initial Version Rev. A | Page 2 of 32 AD5751 FUNCTIONAL BLOCK DIAGRAM DVCC GND AVDD GND COMP1 COMP2 CLEAR CLRSEL VSENSE+ INPUT SHIFT SCLK/OUTEN* REGISTER SDIN/R0* VOUT RANGE AND VOUT SCALING SYNC/RSET* CONTROL VOUT SDO/VFAULT* LOGIC SHORT FAULT STATUS HW SELECT REGISTER AVDD VIN R3 R2 VREF RESET IOUT RANGE SCALING IOUT OVERTEMP REXT1 VOUT SHORT FAULT FAULT/TEMP* R SET REXT2 IOUT OPEN FAULT NC/IFAULT* POWER- IOUT AD5751 ON RESET OPEN FAULT AD2/R1* AD1/R2* AD0/R3* *DENOTES SHARED PIN. SOFTWARE MODE DENOTED BY REGULAR TEXT, HARDWARE MODE DENOTED BYITALIC TEXT. FOR EXAMPLE, FOR FAULT/TEMP PIN, IN SOFTWARE MODE, THIS PIN TAKES ON FAULT FUNCTION. IN HARDWARE MODE, THIS PIN TAKES ONTEMP FUNCTION. Figure 1. Functional Block Diagram Rev. A | Page 3 of 32 07269-001 AD5751 SPECIFICATIONS AVDD = 12 V (± 10%) to 55 V (maximum), DVCC = 2.7 V to 5.5 V, GND = 0 V. IOUT: RLOAD = 300 Ω. All specifications TMIN to TMAX, unless otherwise noted. Table 2. 1 Parameter Min Typ Max Unit Test Conditions/Comments INPUT VOLTAGE RANGE Output unloaded 0 to 4.096 V Input Leakage Current −1 +1 μA REFERENCE INPUT Reference Input Voltage 4.096 V External reference must be exactly as stated; otherwise, accuracy errors show up as error in output Input Leakage Current −1 +1 μA VOLTAGE OUTPUT Output Voltage Ranges 0 5 V 0 10 V AVDD must have minimum 1.3 V headroom or >11.3 V 0 40 V 2 Output Voltage Overranges 0 6 V Programmable overranges; see Detailed Description of Features section 0 12 V 0 44 V Accuracy Total Unadjusted Error (TUE) 3 B Version −0.1 +0.1 % FSR −0.05 ±0.02 +0.05 % FSR TA = 25°C −0.3 +0.3 % FSR A Version3 −0.1 ±0.05 +0.1 % FSR TA = 25°C Relative Accuracy (INL) −0.02 ±0.005 +0.02 % FSR Dead Band on Output, RTI −14 8 +14 mV Referred to 4.096 V input range Offset Error −5 +5 mV 0 V to 10 V range −4 ±0.5 +4 mV TA = 25°C, 0 V to 10 V range −3 +3 mV 0 V to 5 V range −2.2 ±0.3 +2.2 mV T = 25°C, 0 V to 5 V range A −20 +20 mV 0 V to 40 V range −17 ±0.5 +17 mV T = 25°C, 0 V to 40 V range A Gain Error −0.05 +0.05 % FSR 0 V to 5 V, 0 V to 10 V range −0.04 ±0.015 +0.04 % FSR TA = 25°C −0.09 +0.09 % FSR 0 V to 40 V range −0.05 ±0.02 +0.05 % FSR TA = 25°C 4 Gain Error TC ±0.5 ppm FSR/°C All ranges Full-Scale Error −0.05 +0.05 % FSR 0 V to 5 V, 0 V to 10 V range −0.04 ±0.015 +0.04 % FSR TA = 25°C −0.09 +0.09 % FSR 0 V to 40 V range −0.05 ±0.02 +0.05 % FSR TA = 25°C 4 Full-Scale Error TC ±1.5 ppm FSR/°C All ranges 4 OUTPUT CHARACTERISTICS Headroom 1.3 V Output unloaded Short-Circuit Current 15 mA Load 1 kΩ For specified performance, 0 V to 5 V and 0 V to 10 V ranges 5 kΩ For specified performance, 0 V to 40 V range Rev. A | Page 4 of 32 AD5751 1 Parameter Min Typ Max Unit Test Conditions/Comments Capacitive Load Stability TA = 25°C R = ∞ 1 nF LOAD RLOAD = 1 kΩ 1 nF R = ∞ 2 μF External compensation capacitor required; LOAD see Driving Large Capacitive Loads section DC Output Impedance 0.12 Ω Settling Time 0 V to 5 V Range, ¼ to ¾ Step 7 μs Specified with 2 kΩ || 220 pF, ±0.05% 0 V to 5 V Range, 40 mV Input Step 4.5 μs Specified with 2 kΩ || 220 pF, ±0.05% 0 V to 40 V Range, ¼ to ¾ Step 15.8 μs Specified with 5 kΩ || 220 pF, ±0.05% Slew Rate 2 V/μs Specified with 1 kΩ || 220 pF Output Noise 3.5 μV rms 0.1 Hz to 10 Hz bandwidth 45.5 μV rms 100 kHz bandwidth; specified with 2 kΩ || 220 pF Output Noise Spectral Density 165 nV/√Hz Measured at 10 kHz; specified with 2 kΩ || 220 pF AC PSRR 65 dB 200 mV, 50 Hz/60 Hz sine wave superimposed on power supply voltage DC PSRR 10 μV/V CURRENT OUTPUT Output Current Ranges 0 24 mA 0 20 mA 3.92 20 mA 2 Output Current Overranges 0 24.5 mA See Detailed Description of Features section 0 20.4 mA See Detailed Description of Features section 3.92 20.4 mA See Detailed Description of Features section ACCURACY (INTERNAL RSET) Total Unadjusted Error (TUE) B Version3 −0.2 +0.2 % FSR −0.08 ±0.03 +0.08 % FSR TA = 25°C A Version3 −0.5 +0.5 % FSR −0.3 ±0.15 +0.3 % FSR TA = 25°C Relative Accuracy (INL) −0.02 ±0.01 +0.02 % FSR Offset Error −16 +16 μa −10 +5 +10 μa TA = 25°C 4 Offset Error TC ±3 ppm FSR/°C Dead Band on Output, RTI 8 +14 mV Referred to 4.096 V input range Gain Error −0.2 +0.2 % FSR −0.125 ±0.02 +0.125 % FSR T = 25°C A 4 Gain TC ±10 ppm FSR/°C Full-Scale Error −0.2 +0.2 % FSR −0.125 ±0.02 +0.125 % FSR TA = 25°C 4 Full-Scale TC ±4 ppm FSR/°C ACCURACY (EXTERNAL RSET) Total Unadjusted Error (TUE) B Version3 −0.1 +0.1 % FSR −0.08 ±0.03 +0.08 % FSR T = 25°C A A Version3 −0.3 +0.3 % FSR −0.1 ±0.02 +0.1 % FSR TA = 25°C Relative Accuracy (INL) −0.02 ±0.01 +0.02 % FSR Offset Error −14 +14 μA −11 +5 +11 TA = 25°C 4 Offset Error TC ±2 ppm FSR/°C Dead Band on Output, RTI 8 +14 mV Referred to 4.096 V input range Gain Error −0.08 +0.08 % FSR −0.07 ±0.02 +0.07 % FSR T = 25°C A Rev. A | Page 5 of 32 AD5751 1 Parameter Min Typ Max Unit Test Conditions/Comments 4 Gain TC ±1 ppm FSR/°C Full-Scale Error −0.1 +0.1 % FSR −0.07 ±0.02 +0.07 % FSR TA = 25°C 4 Full-Scale TC ±2 ppm FSR/°C 4 OUTPUT CHARACTERISTICS Current Loop Compliance Voltage 0 AV − 2.75 V DD Resistive Load Chosen such that compliance is not exceeded Inductive Load See test conditions/comments column H Needs appropriate capacitor at higher inductance values; see Driving Inductive Loads section Settling Time 4 mA to 20 mA, Full-Scale Step 8.5 μs 250 Ω load 120 μA Step, 4 mA to 20 mA Range 1.2 μs 250 Ω load DC PSRR 1 μA/V Output Impedance 130 MΩ 4 DIGITAL INPUTS JEDEC compliant Input High Voltage, V 2 V IH Input Low Voltage, VIL 0.8 V Input Current −1 +1 μA Per pin Pin Capacitance 5 pF Per pin 4 DIGITAL OUTPUTS FAULT, IFAULT, TEMP, VFAULT V , Output Low Voltage 0.4 V 10 kΩ pull-up resistor to DVCC OL 0.6 V At 2.5 mA V , Output High Voltage 3.6 V 10 kΩ pull-up resistor to DVCC OH SDO VOL, Output Low Voltage 0.5 0.5 V Sinking 200 μA V , Output High Voltage DVCC − 0.5 DVCC − 0.5 V Sourcing 200 μA OH High Impedance Output 3 pF Capacitance High Impedance Leakage Current −1 +1 μA POWER REQUIREMENTS AVDD 10.8 55 V DV CC Input Voltage 2.7 5.5 V AIDD 4.4 5.6 mA Output unloaded, output disabled 5.2 6.2 mA Current output enabled 5.2 6.2 mA Voltage output enabled DICC 0.3 1 mA VIH = DVCC, VIL = GND Power Dissipation 108 mW AVDD = 24 V, outputs unloaded 1 Temperature range: −40°C to +105°C; typical at +25°C. 2 Overranges are nominal; gain and offset are not trimmed as per nominal ranges. 3 Specification includes gain and offset errors, over temperature, and drift after 1000 hours, TA = 125°C. 4 Guaranteed by characterization, but not production tested. Rev. A | Page 6 of 32 AD5751 TIMING CHARACTERISTICS AVDD = 12 V (± 10%) to 55 V (maximum), DVCC = 2.7 V to 5.5 V, GND = 0 V. VOUT: RLOAD = 2 kΩ (5 kΩ for 0 V to 40 V range), CL = 200 pF, IOUT: RLOAD = 300 Ω. All specifications TMIN to TMAX, unless otherwise noted. Table 3. 1, 2 Parameter Limit at TMIN, TMAX Unit Description t1 20 ns min SCLK cycle time t2 8 ns min SCLK high time t3 8 ns min SCLK low time t 5 ns min SYNC falling edge to SCLK falling edge setup time 4 th th t 10 ns min 16 SCLK falling edge to SYNC rising edge (on 24 SCLK falling edge if using PEC) 5 t 5 ns min 6 Minimum SYNC high time (write mode) t7 5 ns min Data setup time t8 5 ns min Data hold time t , t 1.5 μs max CLEAR pulse low/high activation time 9 10 t 5 ns min Minimum SYNC high time (read mode) 11 t 40 ns max SCLK rising edge to SDO valid (SDO C = 15 pF) 12 L t13 10 ns min RESET pulse low time 1 Guaranteed by characterization, but not production tested. 2 All input signals are specified with tR = tF = 5 ns (10% to 90% of DVCC) and timed from a voltage level of 1.2 V. Timing Diagrams t 1 SCLK 12 16 t t 3 2 t 6 t t 4 5 SYNC t 8 t 7 SDIN D15 D0 CLEAR t 10 t 9 VOUT RESET t 13 Figure 2. Write Mode Timing Diagram Rev. A | Page 7 of 32 07269-003 AD5751 SCLK t SYNC 11 SDIN A2 A1 A0 R = 1 0 X X X X X X X X X X X t 12 PEC OVER IOUT VOUT SDO X X X X X R3 R2 R1 R0 CLRSEL OUTEN RSET ERROR TEMP FAULT FAULT Figure 3. Readback Mode Timing Diagram Rev. A | Page 8 of 32 07269-004 AD5751 ABSOLUTE MAXIMUM RATINGS TA = 25°C, unless otherwise noted. Transient currents of up to 100 mA do not cause SCR latch-up. Table 4. Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress Parameter Rating rating only; functional operation of the device at these or any AVDD to GND −0.3 V to +58 V other conditions above those indicated in the operational DVCC to GND −0.3 V to +7 V section of this specification is not implied. Exposure to absolute Digital Inputs to GND −0.3 V to DVCC + 0.3 V, or 7 V (whichever is less) maximum rating conditions for extended periods may affect Digital Outputs to GND −0.3 V to DV + 0.3 V, or 7 V CC device reliability. (whichever is less) ESD CAUTION VREF to GND −0.3 V to +7 V VSENSE+ to GND −0.3 V to AVDD VIN to GND −0.3 V to +7 V VOUT, IOUT to GND −0.3 V to AVDD Operating Temperature Range Industrial −40°C to +105°C Storage Temperature Range −65°C to +150°C Junction Temperature (TJ max) 125°C 32-Lead LFCSP Package θ Thermal Impedance 28°C/W JA Lead Temperature JEDEC industry standard Soldering J-STD-020 Rev. A | Page 9 of 32 AD5751 PIN CONFIGURATION AND FUNCTION DESCRIPTIONS PIN 1 INDICATOR SDO/VFAULT 1 24 VSENSE+ CLRSEL 2 23 VOUT CLEAR 3 22 GND AD5751 DVCC 4 21 GND TOP VIEW GND 5 20 COMP1 (Not to Scale) SYNC/RSET 6 19 COMP2 SCLK/OUTEN 7 18 IOUT SDIN/R0 8 17 AVDD NOTES 1. NC = NO CONNECT. 2. THE EXPOSED PADDLE IS TIED TO GND. Figure 4. Pin Configuration Table 5. Pin Function Descriptions Pin No. Mnemonic Description 1 SDO/VFAULT Serial Data Output (SDO). In software mode, this pin is used to clock data from the input shift register in readback mode. Data is clocked out on the rising edge of SCLK and is valid on the falling edge of SCLK. This pin is a CMOS output. Short-Circuit Fault Alert (VFAULT). In hardware mode, this pin acts as a short-circuit fault alert pin and is asserted low when a short-circuit error is detected. This pin is an open-drain output and must be connected to a pull-up resistor. 2 CLRSEL In hardware or software mode, this pin selects the clear value, either zero-scale or midscale code. In software mode, this pin is implemented as a logic OR with the internal CLRSEL bit. 3 CLEAR Active High Input. Asserting this pin sets the output current/voltage to zero-scale code or midscale code of range selected (user-selectable). CLEAR is a logic OR with the internal clear bit. See the Asynchronous Clear (CLEAR) section for more details. In software mode, during power-up, the CLEAR pin level determines the power-on condition of the voltage channel, which can be active 0 V or tristate. 4 DVCC Digital Power Supply. 5 GND Ground Connection. 6 SYNC/RSET Positive Edge-Sensitive Latch (SYNC). In software mode, a rising edge parallel loads the input shift register data into the AD5751, also updating the output. Resistor Select (RSET). In hardware mode, this pin selects whether the internal or the external current sense resistor is used. If RSET = 0, the external sense resistor is chosen. If RSET = 1, the internal sense resistor is chosen. 7 SCLK/OUTEN Serial Clock Input (SCLK). In software mode, data is clocked into the input shift register on the falling edge of SCLK. This pin operates at clock speeds up to 50 MHz. Output Enable (OUTEN). In hardware mode, this pin acts as an output enable pin. 8 SDIN/R0 Serial Data Input (SDIN). In software mode, data must be valid on the falling edge of SCLK. Range Decode Bit (R0). In hardware mode, this pin, in conjunction with R1, R2, and R3, selects the output current/voltage range setting on the part. 9 AD2/R1 Device Addressing Bit (AD2). In software mode, this pin, in conjunction with AD0 and AD1, allows up to eight devices to be addressed on one bus. Range Decode Bit (R1). In hardware mode, this pin, in conjunction with R0, R2, and R3, selects the output current/voltage range setting on the part. Rev. A | Page 10 of 32 07269-005 AD2/R1 9 32 NC/IFAULT AD1/R2 10 31 FAULT/TEMP AD0/R3 11 30 RESET REXT2 12 29 HW SELECT REXT1 13 28 NC VREF 14 27 NC VIN 15 26 NC GND 16 25 NC AD5751 Pin No. Mnemonic Description 10 AD1/R2 Device Addressing Bit (AD1). In software mode, this pin, in conjunction with AD0 and AD2, allows up to eight devices to be addressed on one bus. Range Decode Bit (R2). In hardware mode, this pin, in conjunction with R0, R1, and R3, selects the output current/voltage range setting on the part. 11 AD0/R3 Device Addressing Bit (AD0). In software mode, this pin, in conjunction with AD1 and AD2, allows up to eight devices to be addressed on one bus. Range Decode Bit (R3). In hardware mode, this pin, in conjunction with R0, R1, and R2, selects the output current/voltage range setting on the part. 12, 13 REXT2, REXT1 A 15 kΩ external current setting resistor can be connected between the REXT1 and REXT2 pins to improve the IOUT temperature drift performance. 14 VREF Buffered Reference Input. 15 VIN Buffered Analog Input (0 V to 4.096 V). 16 GND Ground Connection. 17 AVDD Positive Analog Supply. 18 IOUT Current Output. 19, 20 COMP2, COMP1 Optional Compensation Capacitor Connections for the Voltage Output Buffer. These are used to drive higher capacitive loads on the output. These pins also reduce overshoot on the output. Care should be taken when choosing the value of the capacitor connected between the COMP1 and COMP2 pins because it has a direct influence on the settling time of the output. See the Driving Large Capacitive Loads section for further details. 21 GND Ground Connection. 22 GND Ground Connection. 23 VOUT Buffered Analog Output Voltage. 24 VSENSE+ Sense Connection for the Positive Voltage Output Load Connection. 25, 26, 27, 28 NC No Connect. Can be tied to GND. 29 HW SELECT This part is used to configure the part to hardware or software mode. HW SELECT = 0 selects software control. HW SELECT = 1 selects hardware control. 30 RESET In software mode, this pin resets the part to its power-on state. Active low. In hardware mode, there is no reset. If using the part in hardware mode, the RESET pin should be tied high. 31 FAULT/TEMP Fault Alert (FAULT). In software mode, this pin acts as a general fault alert pin. It is asserted low when an open-circuit, short-circuit, overtemperature error, or PEC interface error is detected. This pin is an open- drain output and must be connected to a pull-up resistor. Overtemperature Fault (TEMP). In hardware mode, this pin acts as an overtemperature fault pin. It is asserted low when an overtemperature error is detected. This pin is an open-drain output and must be connected to a pull-up resistor. 32 NC/IFAULT No Connect (NC). In software mode, this pin is a no connect. Instead, tie this pin to GND. Open-Circuit Fault Alert (IFAULT). In hardware mode, this pin acts as an open-circuit fault alert pin. It is asserted low when an open-circuit error is detected. This pin is an open-drain output and must be connected to a pull-up resistor. 33 (EPAD) Exposed paddle The exposed paddle is tied to GND. Rev. A | Page 11 of 32 AD5751 TYPICAL PERFORMANCE CHARACTERISTICS 0.010 0.10 0V TO 5V 0V TO 5V POSITIVE TUE 0.008 0V TO 10V 0.08 0V TO 10V POSITIVE TUE 0V TO 40V 0V TO 40V POSITIVE TUE 0.006 0V TO 5V NEGATIVE TUE 0.06 0VTO 10VNEGATIVETUE 0VTO 40VNEGATIVETUE 0.004 0.04 0.02 0.002 0 0 –0.002 –0.02 –0.04 –0.004 –0.006 –0.06 –0.008 –0.08 –0.010 –0.10 –40 25 105 TEMPERATURE (°C) V (V) IN Figure 8. Total Unadjusted Error vs. Temperature Figure 5. Integral Nonlinearity Error vs. VIN 0.05 0.010 0V TO 5V RANGE 0V TO 5V RANGE 0V TO 10V RANGE 0.04 0V TO 10V RANGE 0.008 0V TO 40V RANGE 0V TO 40V RANGE 0.03 0.006 0.004 0.02 0.002 0.01 0 0 –0.002 –0.01 –0.004 –0.02 –0.006 –0.03 –0.008 –0.04 –0.010 –40 25 105 –40 25 105 TEMPERATURE (°C) TEMPERATURE (°C) Figure 6. Integral Nonlinearity Error vs. Temperature Figure 9. Full-Scale Error vs. Temperature 0.04 0.010 0V TO 5V 0V TO 5V RANGE 0V TO 10V 0V TO 10V RANGE 0.008 0.03 0V TO 40V 0V TO 40V RANGE 0.006 0.02 0.004 0.01 0.002 0 0 –0.002 –0.01 –0.004 –0.02 –0.006 –0.03 –0.008 –0.04 –0.010 –40 25 105 TEMPERATURE (°C) V (V) IN Figure 10. Gain Error vs. Temperature Figure 7. Total Unadjusted Error vs. V IN Rev. A | Page 12 of 32 TOTAL UNADJUSTED ERROR (%FSR) INTEGRAL NONLINEARITY ERROR (%FSR) INTEGRAL NONLINEARITY ERROR (%FSR) 0.020 0.020 0.293 0.293 0.585 0.585 0.878 0.878 1.170 1.170 1.463 1.463 1.755 1.755 2.048 2.048 2.341 2.341 2.633 2.633 2.926 2.926 3.218 3.218 3.511 3.511 3.803 3.803 4.096 4.096 07269-015 07269-016 07269-014 POSITIVE/NEGATIVE TOTAL UNADJUSTED GAIN ERROR (%FSR) FULL-SCALE ERROR (%FSR) ERROR (%FSR) 07269-019 07269-018 07269-017 AD5751 1.00 4.0 0V TO 5V RANGE V HEADROOM, LOAD OFF DD 3.5 0V TO 10V RANGE 0V TO 40V RANGE 0.95 3.0 2.5 0.90 2.0 1.5 0.85 1.0 0.5 0.80 0 –0.5 0.75 –1.0 0.70 –1.5 –40 25 105 –40 25 105 TEMPERATURE (°C) TEMPERATURE (°C) Figure 11. Offset Error vs. Temperature Figure 14. AVDD Headroom, 0 V to 10 V Range, Output Set to 10 V, Load Off 0.007 0.010 5V LINEARITY, NO LOAD 5V RANGE 10V LINEARITY, NO LOAD 0.008 0.006 40V LINEARITY, NO LOAD 0.006 0.005 0.004 0.004 0.002 0.003 0 0.002 –0.002 0.001 –0.004 0 –0.006 –0.001 –0.008 –0.010 –0.002 24 48 55 –15 –13 –11 –9 –7 –5 –3 –1 1 3 5 7 9 11 13 15 SUPPLY VOLTAGE (V) SOURCE/SINK CURRENT (mA) Figure 12. INL Error vs. Supply Voltage Figure 15. Source and Sink Capability of Output Amplifier 0.010 12 0.008 10 0.006 0.004 8 0V TO 5V POSITIVE TUE 0.002 0V TO 10V POSITIVE TUE 0V TO 40V POSITIVE TUE 6 0 0V TO 5V NEGATIVE TUE –0.002 0V TO 10V NEGATIVE TUE 0V TO 40V NEGATIVE TUE 4 –0.004 –0.006 2 –0.008 0 –0.010 24 48 55 –8 –3 2 7 12 17 22 27 SUPPLY VOLTAGE (V) TIME (µs) Figure 13. Total Unadjusted Error vs. Supply Voltage Figure 16. Full-Scale Positive Step, 10 V Range Rev. A | Page 13 of 32 TOTAL UNADJUSTED ERROR (%FSR) INTEGRAL NONLINEARITY ERROR (%FSR) OFFSET ERROR (mV) 07269-020 07269-022 07269-021 OUTPUT VOLTAGE DELTA (V) HEADROOM (V) VOLTAGE (V) 07269-025 07269-023 07269-024 AD5751 12 10 8 6 4 2 5µV/DIV 1s/DIV 0 –8 –3 2 7 12 17 22 27 TIME (µs) Figure 17. Full-Scale Negative Step, 10 V Range Figure 20. Peak-to-Peak Noise (0.1 Hz to 10 Hz Bandwidth) 40 35 30 25 20 15 10 5 0 100µV/DIV 1s/DIV –5 –1.0 –0.5 0 0.5 1.0 1.5 2.0 2.5 TIME (ms) Figure 18. VOUT vs. Time on Power-Up, Load = 2 kΩ || 200 pF Figure 21. Peak-to-Peak Noise (100 kHz Bandwidth) 4.0 1.0 3.5 0.8 3.0 1 V DD 0.6 2.5 2.0 0.4 1.5 0.2 1.0 V 2 OUT 0 0.5 0 –0.2 –1.5 –1.0 –0.5 0 0.5 1.0 1.5 2.0 B CH1 5.00V CH2 20.0mV M1.0µs A CH1 3.00V W TIME (ms) Figure 22. VDD and VOUT vs. Time on Power-Up Figure 19. VOUT Enable Glitch, Load = 2 kΩ || 1 nF Rev. A | Page 14 of 32 V (mV) OUT VOLTAGE (V) 07269-028 07269-026 07269-027 V (V) DD 07269-030 07269-029 V (V) 07269-031 OUT AD5751 CURRENT OUTPUT 0.005 0.010 4mA TO 20mA EXTERNAL R RESISTOR SET 4mA TO 20mA INTERNAL R LINEARITY SET 0mA TO 20mA EXTERNAL R RESISTOR 0.004 SET 0mA TO 20mA INTERNAL R LINEARITY 0.008 SET 0mA TO 24mA EXTERNAL R RESISTOR SET 0mA TO 24mA INTERNAL R LINEARITY SET 0.003 0.006 0.002 0.004 0.001 0.002 0 0 –0.001 –0.002 –0.002 –0.004 –0.003 –0.006 –0.004 –0.008 –0.005 –0.010 24V 48V 55V SUPPLY VOLTAGE (AVDD) V (V) IN Figure 23. Integral Nonlinearity Error vs. V , External R Resistor Figure 26. Integral Nonlinearity Current Mode, Internal RSET Sense Resistor IN SET 0.05 0.005 4mA TO 20mA INTERNAL R RESISTOR 4mA TO 20mA EXTERNAL R TUE SET SET 0mA TO 20mA INTERNAL R RESISTOR 0mA TO 20mA EXTERNAL R TUE SET 0.04 SET 0.004 0mA TO 24mA INTERNAL R RESISTOR 0mA TO 24mA EXTERNAL R TUE SET SET 0.03 0.003 0.002 0.02 0.01 0.001 0 0 –0.01 –0.001 –0.002 –0.02 –0.03 –0.003 –0.04 –0.004 –0.05 –0.005 V (V) V (V) IN IN Figure 24. Integral Nonlinearity Error vs. V , Internal R Resistor Figure 27. Total Unadjusted Error vs. VIN, External RSET Resistor IN SET 0.05 0.010 4mA TO 20mA INTERNAL R TUE 4mA TO 20mA EXTERNAL R LINEARITY SET SET 0mA TO 20mA INTERNAL R TUE 0mA TO 20mA EXTERNAL R LINEARITY 0.04 SET 0.008 SET 0mA TO 24mA EXTERNAL R LINEARITY 0mA TO 24mA INTERNAL R TUE SET SET 0.03 0.006 0.02 0.004 0.01 0.002 0 0 –0.01 –0.002 –0.02 –0.004 –0.03 –0.006 –0.04 –0.008 –0.05 –0.010 24V 48V 55V SUPPLY VOLTAGE (AVDD) V (V) IN Figure 25. Integral Nonlinearity Current Mode, External R Sense Resistor Figure 28. Total Unadjusted Error vs. VIN, Internal RSET Resistor SET Rev. A | Page 15 of 32 INTEGRAL NONLINEARITY (%FSR) INTEGRAL NONLINEARITY (%FSR) INTEGRAL NONLINEARITY (%FSR) 0.020 0.020 0.293 0.293 0.585 0.585 0.878 0.878 1.170 1.170 1.463 1.463 1.755 1.755 2.048 2.048 2.341 2.341 2.633 2.633 2.926 2.926 3.218 3.218 3.511 3.511 3.803 3.803 4.096 4.096 07269-034 07269-033 07269-032 INTEGRAL NONLINEARITY (%FSR) TOTAL UNADJUSTED ERROR (%FSR) TOTAL UNADJUSTED ERROR (%FSR) 0.020 0.020 0.293 0.293 0.585 0.585 0.878 0.878 1.170 1.170 1.463 1.463 1.755 1.755 2.048 2.048 2.341 2.341 2.633 2.633 2.926 2.926 3.218 3.218 3.511 3.511 3.803 3.803 4.096 4.096 07269-037 07269-036 07269-035 AD5751 0.020 0.005 4mA TO 20mA EXTERNAL R POSITIVE TUE SET 4mA TO 20mA EXTERNAL R LINEARITY SET 0mA TO 20mA EXTERNAL R POSITIVE TUE SET 0mA TO 20mA EXTERNAL R LINEARITY 0.004 SET 0.015 0mA TO 24mA EXTERNAL R POSITIVE TUE SET 0mA TO 24mA EXTERNAL R LINEARITY SET 0.003 0.010 0.002 0.005 0.001 0 0 –0.001 –0.005 –0.002 –0.010 4mA TO 20mA EXTERNAL R NEGATIVE TUE –0.003 SET 0mA TO 20mA EXTERNAL R NEGATIVE TUE SET –0.015 –0.004 0mA TO 24mA EXTERNAL R NEGATIVE TUE SET –0.005 –0.020 24V 48V 55V –40 25 105 SUPPLY VOLTAGE (AVDD) TEMPERATURE (°C) Figure 29. Total Unadjusted Error Current Mode, External RSET Sense Resistor Figure 32. Integral Nonlinearity Error vs. Temperature, External R Sense Resistor SET 0.010 4mA TO 20mA INTERNAL R NEGATIVE TUE SET 0.10 0mA TO 20mA INTERNAL R NEGATIVE TUE SET 4mA TO 20mA INTERNAL R POSITIVE TUE SET 0.005 0mA TO 20mA INTERNAL R POSITIVE TUE 0.08 SET 0mA TO 24mA INTERNAL R POSITIVE TUE SET 0.06 4mA TO 20mA INTERNAL R NEGATIVE TUE SET 0 0mA TO 24mA INTERNAL 0mA TO 20mA INTERNAL R NEGATIVE TUE SET 0.04 R NEGATIVE TUE 0mA TO 24mA INTERNAL R NEGATIVE TUE SET SET 4mA TO 20mA INTERNAL –0.005 R POSITIVE TUE 0.02 SET 0 –0.010 –0.02 –0.015 –0.04 –0.06 –0.020 0mA TO 20mA INTERNAL R POSITIVE TUE SET 0mA TO 24mA INTERNAL R POSITIVE TUE SET –0.08 –0.025 24V 48V 55V –0.10 –40 25 105 SUPPLY VOLTAGE (AVDD) TEMPERATURE (°C) Figure 30. Total Unadjusted Error Current Mode, Internal R Sense Resistor SET Figure 33. Total Unadjusted Error vs. Temperature, Internal R Sense Resistor SET 0.005 0.10 4mA TO 20mA INTERNAL R LINEARITY SET 0mA TO 20mA INTERNAL R LINEARITY 0.004 SET 0.08 0mA TO 24mA INTERNAL R LINEARITY SET 0.003 0.06 0.002 0.04 0.001 0.02 0 0 –0.001 –0.02 –0.002 4mA TO 20mA EXTERNAL R POSITIVE TUE SET –0.04 0mA TO 20mA EXTERNAL R POSITIVE TUE SET –0.003 0mA TO 24mA EXTERNAL R POSITIVE TUE –0.06 SET 4mA TO 20mA EXTERNAL R NEGATIVE TUE SET –0.004 –0.08 0mA TO 20mA EXTERNAL R NEGATIVE TUE SET 0mA TO 24mA EXTERNAL R NEGATIVE TUE SET –0.005 –0.10 –40 25 105 –40 25 105 TEMPERATURE (°C) TEMPERATURE (°C) Figure 31. Integral Nonlinearity Error vs. Temperature, Figure 34. Total Unadjusted Error vs. Temperature, External R Sense Resistor SET Internal RSET Sense Resistor Rev. A | Page 16 of 32 INTEGRAL NONLINEARITY (%FSR) TOTAL UNADJUSTED ERROR (%FSR) TOTAL UNADJUSTED ERROR (%FSR) 07269-040 07269-039 07269-038 INTEGRAL NONLINEARITY (%FSR) POSITIVE/NEGATIVE TUE (%FSR) POSITIVE/NEGATIVE TUE (%FSR) 07269-043 07269-042 07269-041 AD5751 50 4 45 3 40 2 35 30 1 25 0 20 15 –1 10 4mA TO 20mA EXTERNAL R SET 4mA TO 20mA EXTERNAL R SET –2 0mA TO 20mA EXTERNAL R SET 0mA TO 20mA EXTERNAL R SET 5 0mA TO 24mA EXTERNAL R SET 0mA TO 24mA EXTERNAL R SET 0 –3 –40 25 105 –40 25 105 TEMPERATURE (°C) TEMPERATURE (°C) Figure 35. Zero-Scale Error vs. Temperature, External RSET Sense Resistor Figure 38. Offset Error vs. Temperature, External RSET Sense Resistor 40 0.05 4mA TO 20mA EXTERNAL R SET 0mA TO 20mA EXTERNAL R 0.04 SET 35 0mA TO 24mA EXTERNAL R SET 0.03 30 0.02 25 0.01 20 0 –0.01 15 –0.02 10 –0.03 4mA TO 20mA INTERNAL R SET 0mA TO 20mA INTERNAL R 5 SET –0.04 0mA TO 24mA INTERNAL R SET 0 –0.05 –40 25 105 –40 25 105 TEMPERATURE (°C) TEMPERATURE (°C) Figure 36. Zero-Scale Error vs. Temperature, Internal RSET Sense Resistor Figure 39. Full-Scale Error vs. Temperature, External RSET Sense Resistor 0.10 3 4mA TO 20mA INTERNAL R SET 0mA TO 20mA INTERNAL R 0.08 SET 0mA TO 24mA INTERNAL R SET 2 0.06 0.04 1 0.02 0 0 –0.02 –1 –0.04 –0.06 4mA TO 20mA INTERNAL R SET –2 0mA TO 20mA INTERNAL R SET –0.08 0mA TO 24mA INTERNAL R SET –0.10 –3 –40 25 105 –40 25 105 TEMPERATURE (°C) TEMPERATURE (°C) Figure 40. Full-Scale Error vs. Temperature, Internal RSET Sense Resistor Figure 37. Offset Error vs. Temperature, Internal RSET Sense Resistor Rev. A | Page 17 of 32 OFFSET ERROR (µA) ZERO-SCALE ERROR (µA) ZERO-SCALE ERROR (µA) 07269-046 07269-045 07269-044 FULL-SCALE ERROR (%FSR) FULL-SCALE ERROR (%FSR) OFFSET ERROR (µA) 07269-047 07269-049 07269-048 AD5751 0.10 12 0.000010 4mA TO 20mA EXTERNAL R SET 0mA TO 20mA EXTERNAL R 0.08 SET 0.000008 10 0mA TO 24mA EXTERNAL R SET 0.06 0.000006 8 0.000004 0.04 0.000002 0.02 6 I OUT 0 0 4 –0.000002 –0.02 –0.000004 –0.04 2 –0.000006 –0.06 0 V –0.000008 –0.08 DD –2 –0.000010 –0.10 –10 –8 –6 –4 –2 0 2 4 6 8 10 –40 25 105 TIME (ms) TEMPERATURE (°C) Figure 44. Output Current vs. Time on V Power-Up Figure 41. Gain Error vs. Temperature, External RSET Sense Resistor DD 0 0.10 4mA TO 20mA INTERNAL R SET 0mA TO 20mA INTERNAL R 0.08 SET –2 0mA TO 24mA INTERNAL R SET 0.06 –4 0.04 –6 0.02 –8 0 –10 –0.02 –12 –0.04 –14 –0.06 –16 –0.08 –18 –0.10 –2 –1 01 23 45 67 8 –40 25 105 TEMPERATURE (°C) TIME (µs) Figure 45. Output Current vs. Time on Output Enable, 0 mA to 20 mA Range Figure 42. Gain Error vs. Temperature, Internal RSET Sense Resistor 2.10 0.025 2.05 0.020 2.00 1.95 0.015 1.90 1.85 0.010 1.80 1.75 0.005 AV COMPLIANCE VOLTAGE DD 1.70 0 1.65 –40 25 105 –12 –6 1 8 14 21 28 34 41 48 54 61 68 TEMPERATURE (°C) TIME (µs) Figure 46. 4 mA to 20 mA Output Current Step Figure 43. Output Compliance vs. Temperature Tested When I = 10.8 mA, 0 mA to 24 mA Range Selected OUT Rev. A | Page 18 of 32 GAIN ERROR (%FSR) GAIN ERROR (%FSR) COMPLIANCE (V) 07269-052 07269-051 07269-050 V (V) DD CURRENT (A) I (µA) OUT 07269-054 07269-055 I (A) 07269-053 OUT AD5751 3000 4.10 4.05 2500 4.00 2000 DV = 5V CC 3.95 1500 3.90 1000 3.85 500 3.80 DV = 3V CC 0 3.75 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 24 48 55 LOGIC LEVEL (V) AV (V) DD Figure 47. DICC vs. Logic Input Voltage Figure 49. AI vs. AV , I = 0 mA DD DD OUT 4.10 4.05 4.00 3.95 3.90 3.85 3.80 3.75 24 48 55 AV (V) DD Figure 48. AIDD vs. AVDD, VOUT = 0 V Rev. A | Page 19 of 32 AI (mA) DI (µA) CC DD 07269-057 07269-056 AI (mA) DD 07269-058 AD5751 TERMINOLOGY Zero-Scale TC Total Unadjusted Error (TUE) TUE is a measure of the output error taking all the various Zero-scale TC is a measure of the change in zero-scale error errors into account: INL error, offset error, gain error, and with a change in temperature. Zero-scale error TC is expressed output drift over supplies, temperature, and time. TUE is in ppm FSR/°C. expressed as a percentage of full-scale range (% FSR). Offset Error Relative Accuracy or Integral Nonlinearity (INL) Offset error is a measurement of the difference between the INL is a measure of the maximum deviation, in % FSR, from a actual VOUT and the ideal VOUT expressed in millivolts (mV) straight line passing through the endpoints of the output driver in the linear region of the transfer function. It can be negative or positive. transfer function. A typical INL vs. input voltage plot is shown in Figure 5. Output Voltage Settling Time Full-Scale Error Output voltage settling time is the amount of time it takes for Full-scale error is the deviation of the actual full-scale analog the output to settle to a specified level for a half-scale input change. output from the ideal full-scale output. Full-scale error is Slew Rate expressed as a percentage of full-scale range (% FSR). The slew rate of a device is a limitation in the rate of change of Full-Scale TC the output voltage. The output slewing speed is usually limited Full-scale TC is a measure of the change in the full-scale error by the slew rate of the amplifier used at its output. Slew rate is with a change in temperature. It is expressed in ppm FSR/°C. measured from 10% to 90% of the output signal and is expressed in V/μs. Gain Error Gain error is a measure of the span error of the output. It is the Current Loop Voltage Compliance deviation in slope of the output transfer characteristic from the Current loop voltage compliance is the maximum voltage at the ideal expressed in % FSR. A plot of gain error vs. temperature is IOUT pin for which the output current is equal to the shown in Figure 10. programmed value. Gain Error TC Power-On Glitch Energy Gain error TC is a measure of the change in gain error with Power-on glitch energy is the impulse injected into the analog changes in temperature. Gain error TC is expressed in ppm output when the AD5751 is powered on. It is specified as the FSR/°C. area of the glitch in nV-sec. Zero-Scale Error Power Supply Rejection Ratio (PSRR) Zero-scale error is the deviation of the actual zero-scale analog PSRR indicates how the output is affected by changes in the output from the ideal zero-scale output. Zero-scale error is power supply voltage. expressed in millivolts (mV). Rev. A | Page 20 of 32 AD5751 THEORY OF OPERATION The AD5751 is a single-channel, low cost, precision, voltage/ one time. The output range is selected by programming the R3 current output driver with hardware or software programmable to R0 bits in the control register (see Table 7 and Table 8). output ranges. The software ranges are configured via an SPI-/ Figure 50 and Figure 51 show a typical configuration of AD5751 in MICROWIRE-compatible serial interface. The hardware ranges software mode and in hardware mode, respectively, in an output are programmed using the range pins (R0 to R3). The analog module system. The HW SELECT pin chooses whether the part input to the AD5751 is provided from a low voltage, single-supply is configured in software or hardware mode. The analog input to DAC (0 V to 4.096 V), which is internally conditioned to provide the AD5751 is provided from a low voltage, single-supply DAC the desired output current/voltage range. such as the AD506x or AD566x, which can provide an output The output current range is programmable across three ranges: range of 0 V to 4.096 V. The supply and reference for the DAC, 0 mA to 20 mA, 0 mA to 24 mA, or 4 mA to 20 mA. The voltage as well as the reference for the AD5751, can be supplied from a output is provided from a separate pin that can be configured to reference such as the ADR392. The AD5751 can operate with a provide 0 V to 5 V, 0 V to 10 V, and 0 V to 40 V output ranges. single supply up to 55 V. An overrange of 20% is available on the 5 V and 10 V output SOFTWARE MODE voltage ranges, and of 10% on the 0 V to 40 V range. The VOUT In current mode, software-selectable output ranges include 0 mA and IOUT pins can be connected together. An overrange of 2% to 20 mA, 0 mA to 24 mA, or 4 mA to 20 mA. is available on the 0 mA to 20 mA, 0 mA to 24 mA, and 4 mA to 20 mA current ranges. The current and voltage outputs are In voltage mode, software-selectable output ranges include 0 V available on separate pins. Only one output can be enabled at to 5 V, 0 V to 10 V, 0 V to 40 V. AVDD AGND ADP1720 AVDD GND AD5751 VSENSE+ ADR392 VREF VDD REFIN VOUT SCLK VOUT RANGE 0V TO 5V, 0V TO 10V, SCALE SDI/DIN VIN 0V TO 40V AD506x MCU SDO AD566x IOUT SYNC1 RANGE IOUT SCALE 0mA TO 20mA, 0mA TO 24mA, SCLK 4mA TO 20mA VOUT SHORT FAULT SDIN IOUT OPEN FAULT SERIAL OVERTEMP FAULT SDO INTERFACE SYNC STATUS REGISTER HW SELECT FAULT Figure 50. Typical System Configuration in Software Mode (Pull-Up Resistors Not Shown for Open-Drain Outputs) Rev. A | Page 21 of 32 07269-006 AD5751 AVDD AGND ADP1720 AVDD GND AD5751 VSENSE+ VREF ADR392 VDD REFIN VOUT SCLK VOUT RANGE SCALE 0V TO 5V, 0V TO 10V, SDI/DIN VIN 0V TO 40V AD506x SDO MCU AD566x SYNC1 IOUT RANGE IOUT SCALE 0mA TO 20mA, DVCC HW SELECT 0mA TO 24mA, 4mA TO 20mA OUTEN R3 R2 OUTPUT RANGE SELECT PINS R1 TEMP VFAULT IFAULT R0 Figure 51. Typical System Configuration in Hardware Mode Using Internal DAC Reference (Pull-Up Resistors Not Shown for Open-Drain Outputs) Table 6. Suggested Parts for Use with the AD5751 DAC Reference Power Resolution/Accuracy Description 1 AD5660 Internal ADP1720 16-bit/12-bit Mid end system, single channel, internal reference AD5664R Internal N/A 16-bit/12-bit Mid end system, quad channel, internal reference AD5668 Internal N/A 16-bit/12-bit Mid end system, octal channel, internal reference AD5060 ADR434 ADP1720 16-bit/16-bit High end system, single channel, external reference AD5064/AD5066 ADR434 N/A 16-bit/16-bit High end system, quad channel, external reference 2 AD5662 ADR392 ADR3922 16-bit/12-bit Mid end system, single channel, external reference AD5664 ADR3922 N/A 16-bit/12-bit Mid end system, quad channel, external reference 1 ADP1720 input range up to 28 V. 2 ADR392 input range up to 15 V. Rev. A | Page 22 of 32 07269-007 AD5751 CURRRENT OUTPUT ARCHITECTURE Driving Large Capacitive Loads The voltage input from the analog input VIN core (0 V to 4.096 V) The voltage output amplifier is capable of driving capacitive loads is either converted to a current (see Figure 52), which is then of up to 1 μF with the addition of a nonpolarized compensation mirrored to the supply rail so that the application simply sees capacitor between the COMP1 and COMP2 pins. a current source output with respect to an internal reference Without the compensation capacitor, up to 20 nF capacitive loads voltage, or it is buffered and scaled to output a software-selectable can be driven. Care should be taken to choose an appropriate unipolar voltage range (see Figure 53). The reference is used to value for the CCOMP capacitor. This capacitor, while allowing the provide internal offsets for range and gain scaling. The selecta- AD5751 to drive higher capacitive loads and reduce overshoot, ble output range is programmable through the digital interface increases the settling time of the part and therefore affects the (software mode) or via the range pins (R0 to R3) (hardware mode). bandwidth of the system. Considered values of this capacitor AVDD should be in the range of 0 nF to 4 nF depending on the trade-off required between settling time, overshoot, and bandwidth. R2 R3 RANGE DECODE POWER-ON STATE OF THE AD5751 FROM INTERFACE T2 On power-up, the AD5751 senses whether hardware or software A2 mode is loaded and sets the power-up conditions accordingly. T1 VIN IOUT VOUT RANGE A1 In software SPI mode, the power-up state of the output is SCALING VREF dependent on the state of the CLEAR pin. If the CLEAR pin is pulled high, the part powers up, driving an active 0 V on the R1 output. If the CLEAR pin is pulled low, the part powers up with Figure 52. Current Output Configuration the voltage output channel in tristate mode. In both cases, the current output channel powers up in the tristate condition (0 mA). This allows the voltage and current outputs to be RANGE DECODE FROM INTERFACE connected together if desired. VSENSE+ To put the part into normal operation, the user must set the VIN OUTEN bit in the control register to enable the output and, in VOUT RANGE (0V TO 4.096V) VOUT SCALING the same write, set the output range configuration using the R3 VREF VOUT SHORT FAULT to R0 range bits. If the CLEAR pin is still high (active) during this write, the part automatically clears to its normal clear state GND as defined by the programmed range and by the CLRSEL pin or Figure 53. Voltage Output the CLRSEL bit (see the Asynchronous Clear (CLEAR) section DRIVING INDUCTIVE LOADS for more details). The CLEAR pin must be taken low to operate the part in normal mode. When driving inductive or poorly defined loads, connect a 0.01 μF capacitor between IOUT and GND. This ensures stability with The CLEAR pin is typically driven directly from a microcontroller. loads beyond 50 mH. There is no maximum capacitance limit. In cases where the power supply for the AD5751 supply is The capacitive component of the load may cause slower settling. independent of the microcontroller power supply, the user can connect a weak pull-up resistor to DVCC or a pull-down resistor Voltage Output Amplifier to ground to ensure that the correct power-up condition is The voltage output amplifier is capable of driving a load of 1 kΩ achieved independent of the microcontroller. A 10 kΩ pull-up/ (for 0 V to 5 V and 0 V to 10 V ranges) and a load of 5 kΩ (for pull-down resistor on the CLEAR pin should be sufficient for 0 V to 40 V range) and capacitive loads up to 2 μF (with an most applications. external compensation capacitor on the COMP1 and COMP2 If hardware mode is selected, the part powers up to the conditions pins). The source and sink capabilities of the output amplifier defined by the R3 to R0 range bits and the status of the OUTEN can be seen in Figure 15. The slew rate is 2 V/μs. or CLEAR pin. It is recommended to keep the output disabled Internal to the device, there is a 2.5 MΩ resistor connected when powering up the part in hardware mode. between VOUT and VSENSE+. If a fault condition occurs, these resistors act to protect the AD5751 by ensuring that the amplifier loop is closed so that the part does not enter into an open-loop condition. The current and voltage are output on separate pins and cannot be output simultaneously. This allows the user to tie both the current and voltage output pins together and configure the end system as a single-channel output. Rev. A | Page 23 of 32 07269-009 07269-008 AD5751 disabled, both the current and voltage channels go into tristate. DEFAULT REGISTERS AT POWER-ON The user must set the OUTEN bit to enable the output and The AD5751 power-on-reset circuit ensures that all registers are simultaneously set the output range configuration. loaded with zero code. In hardware mode, the output can be enabled or disabled using In software SPI mode, the part powers up with all outputs the OUTEN pin. When the output is disabled, both the current disabled (OUTEN bit = 0). The user must set the OUTEN bit in and voltage channels go into tristate. The user must write to the the control register to enable the output and, in the same write, OUTEN pin to enable the output. It is recommended that the set the output range configuration using the R3 to R0 bits. output be disabled when changing the ranges. If hardware mode is selected, the part powers up to the SOFTWARE CONTROL conditions defined by the R3 to R0 bits and the status of the OUTEN pin. It is recommended to keep the output disabled Software control is enabled by connecting the HW SELECT pin when powering up the part in hardware mode. to ground. In software mode, the AD5751 is controlled over a versatile 3-wire serial interface that operates at clock rates up to RESET FUNCTION 50 MHz. It is compatible with SPI, QSPI™, MICROWIRE, and In software mode, the part can be reset using the RESET pin DSP standards. (active low) or the reset bit (reset = 1). A reset disables both the Input Shift Register current and voltage outputs to their power-on condition. The The input shift register is 16 bits wide. Data is loaded into the user must write to the OUTEN bit to enable the output and, in device MSB first as a 16-bit word under the control of a serial RESET the same write, set the output range configuration. The clock input, SCLK. Data is clocked in on the falling edge of SCLK. pin is a level sensitive input; the part stays in reset mode as long The input shift register consists of 16 control bits, as shown in RESET as the pin is low. The reset bit clears to 0 following a Table 7. The timing diagram for this write operation is shown in reset command to the control register. Figure 2. The first three bits of the input shift register are used to set In hardware mode, there is no reset. If using the part in the hardware address of the AD5751 device on the printed circuit hardware mode, the RESET pin should be tied high. board (PCB). Up to eight devices can be addressed per board. OUTEN Bit D11, Bit D1, and Bit D0 must always be set to 0 during any write sequence. In software mode, the output can be enabled or disabled using the OUTEN bit in the control register. When the output is Table 7. Input Shift Register Contents for a Write Operation—Control Register MSB LSB D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 A2 A1 A0 R/W 0 R3 R2 R1 R0 CLRSEL OUTEN Clear RSET Reset 0 0 Table 8. Input Shift Register Descriptions for Control Register Bit Description A2, A1, A0 Used in association with the AD2, AD1, and AD0 external pins to determine which part is being addressed by the system controller. A2 A1 A0 Function 0 0 0 Addresses part with Pin AD2 = 0, Pin AD1 = 0, Pin AD0 = 0. 0 0 1 Addresses part with Pin AD2 = 0, Pin AD1 = 0, Pin AD0 = 1. 0 1 0 Addresses part with Pin AD2 = 0, Pin AD1 = 1, Pin AD0 = 0. 0 1 1 Addresses part with Pin AD2 = 0, Pin AD1 = 1, Pin AD0 = 1. 1 0 0 Addresses part with Pin AD2 = 1, Pin AD1 = 0, Pin AD0 = 0. 1 0 1 Addresses part with Pin AD2 = 1, Pin AD1 = 0, Pin AD0 = 1. 1 1 0 Addresses part with Pin AD2 = 1, Pin AD1 = 1, Pin AD0 = 0. 1 1 1 Addresses part with Pin AD2 = 1, Pin AD1 = 1, Pin AD0 = 1. R/W Indicates a read from or a write to the addressed register. Rev. A | Page 24 of 32 AD5751 Bit Description R3, R2, R1, R0 Selects the output configuration in conjunction with RSET. RSET R3 R2 R1 R0 Output Configuration 0 0 0 0 0 4 mA to 20 mA (external 15 kΩ current sense resistor). 0 0 0 0 1 0 mA to 20 mA (external 15 kΩ current sense resistor). 0 0 0 1 0 0 mA to 24 mA (external 15 kΩ current sense resistor). 0 0 0 1 1 Unused command. Do not program. 0 0 1 0 0 Unused command. Do not program. 0 0 1 0 1 0 V to 5 V. 0 0 1 1 0 0 V to 10 V. 0 0 1 1 1 Unused command. Do not program. 0 1 0 0 0 Unused command. Do not program. 0 1 0 0 1 0 V to 6.0 V (20% overrange). 0 1 0 1 0 0 V to 12.0 V (20% overrange). 0 1 0 1 1 Unused command. Do not program. 0 1 1 0 0 Unused command. Do not program. 0 1 1 0 1 Unused command. Do not program. 0 1 1 1 0 0 V to 40 V. 0 1 1 1 1 0 V to 44 V. 1 0 0 0 0 4 mA to 20 mA (internal current sense resistor). 1 0 0 0 1 0 mA to 20 mA (internal current sense resistor). 1 0 0 1 0 0 mA to 24 mA (internal current sense resistor). 1 0 0 1 1 Unused command. Do not program. 1 0 1 0 0 Unused command. Do not program. 1 0 1 0 1 0 V to 5 V. 1 0 1 1 0 0 V to 10 V. 1 0 1 1 1 Unused command. Do not program. 1 1 0 0 0 Unused command. Do not program. 1 1 0 0 1 0 V to 6.0 V (20% overrange). 1 1 0 1 0 0 V to 12.0 V (20% overrange). 1 1 0 1 1 Unused command. Do not program. 1 1 1 0 0 Unused command. Do not program. 1 1 1 0 1 3.92 mA to 20.4 mA (internal current sense resistor). 1 1 1 1 0 0 mA to 20.4 mA (internal current sense resistor). 1 1 1 1 1 0 mA to 24.5 mA (internal current sense resistor). CLRSEL Sets clear mode to zero scale or midscale. See the Asynchronous Clear (CLEAR) section. CLRSEL Function 0 Clear to 0 V. 1 Clear to midscale in unipolar mode; clear to zero scale in bipolar mode. OUTEN Output enable bit. This bit must be set to 1 to enable the outputs. Clear Software clear bit; active high. RSET Select internal/external current sense resistor. RSET Function 1 Select internal current sense resistor; used with R3 to R0 bits to select range. 0 Select external current sense resistor; used with R3 to R0 bits to select range. Reset Resets the part to its power-on state. Rev. A | Page 25 of 32 AD5751 Readback Operation HARDWARE CONTROL Readback mode is activated by selecting the correct device address Hardware control is enabled by connecting the HW SELECT (A2, A1, A0) and then setting the R/W bit to 1. By default, the pin to DVCC. In this mode, the R3, R2, R1, and R0 pins, in SDO pin is disabled. After having addressed the AD5751 for a conjunction with the RSET pin, are used to configure the W to 1 enables the SDO pin and SDO output range, as per Table 8. read operation, setting R/ th data is clocked out on the 5 rising edge of SCLK. After the data In hardware mode, there is no status register. The fault condi- SYNC has been clocked out on SDO, a rising edge on disables tions (open circuit, short circuit, and overtemperature) are (tristate) the SDO pin again. Status register data (see Table 9) available on Pin IFAULT, Pin VFAULT, and Pin TEMP. If any and control register data are both available during the same one of these fault conditions is set, a low is asserted on the read cycle. specific fault pin. IFAULT, VFAULT, and TEMP are open-drain outputs and, therefore, can be connected together to allow the The status bits comprise four read-only bits. They are used to user to generate one interrupt to the system controller to notify the user of specific fault conditions that occur, such as an communicate a fault. If hardwired in this way, it is not possible open circuit or short circuit on the output, overtemperature to isolate which fault occurred in the system. error, or an interface error. If any of these fault conditions occur, a hardware FAULT is also asserted low, which can be used as a TRANSFER FUNCTION hardware interrupt to the controller. The AD5751 consists of an internal signal conditioning block See the Detailed Description of Features section for a full that maps the analog input voltage to a programmed output explanation of fault conditions. range. The available analog input range is 0 V to 4.096 V. For all ranges, both current and voltage, the AD5751 imple- ments a straight linear mapping function, where 0 V maps to the lower end of the selected range and 4.096 V maps to the upper end of the selected range. Table 9. Input Shift Register Contents for a Read Operation—Status Register MSB LSB D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 A2 A1 A0 1 0 R3 R2 R1 R0 CLRSEL OUTEN RSET PEC error OVER TEMP IOUT fault VOUT fault Table 10. Status Bit Options Bit Description PEC Error This bit is set if there is an interface error detected by CRC-8 error checking. See the Detailed Description of Features section. OVER TEMP This bit is set if the AD5751 core temperature exceeds approximately 150°C. IOUT Fault This bit is set if there is an open circuit on the IOUT pin. VOUT Fault This bit is set if there is a short circuit on the VOUT pin. Rev. A | Page 26 of 32 AD5751 DETAILED DESCRIPTION OF FEATURES • A short is detected on the voltage output pin. The short- OUTPUT FAULT ALERT—SOFTWARE MODE circuit current is limited to 15 mA. If this fault is detected, In software mode, the AD5751 is equipped with one FAULT the VFAULT pin is forced low. pin; this is an open-drain output allowing several AD5751 • The core temperature of the AD5751 exceeds approx- devices to be connected together to one pull-up resistor for imately 150°C. If this fault is detected, the TEMP pin is global fault detection. In software mode, the FAULT pin is forced low. forced active low by any one of the following fault scenarios: VOLTAGE OUTPUT SHORT-CIRCUIT PROTECTION • The voltage at IOUT attempts to rise above the compliance range due to an open-loop circuit or insufficient power Under normal operation the voltage output sinks and sources supply voltage. The internal circuitry that develops the up to 12 mA and maintains specified operation. The maximum fault output avoids using a comparator with window limits current that the voltage output delivers is 15 mA; this is the because this requires an actual output error before the fault short-circuit current. output becomes active. Instead, the signal is generated ASYNCHRONOUS CLEAR (CLEAR) when the internal amplifier in the output stage has less CLEAR is an active high clear that allows the voltage output to than approximately 1 V of remaining drive capability. be cleared to either zero-scale code or midscale code, and is Thus, the fault output activates slightly before the com- user-selectable via the CLRSEL pin or the CLRSEL bit of the pliance limit is reached. Because the comparison is made input shift register, as described in Table 8. (The clear select within the feedback loop of the output amplifier, the output feature is a logical OR function of the CLRSEL pin and the accuracy is maintained by its open-loop gain, and an CLRSEL bit). The current loop output clears to the bottom of its output error does not occur before the fault output programmed range. When the CLEAR signal is returned low, becomes active. the output returns to its programmed value or to a new • A short is detected on the voltage output pin (VOUT). The programmed value. A clear operation can also be performed via short-circuit current is limited to 15 mA. the clear command in the control register. • An interface error is detected due to the packet error checking failure (PEC). See the Packet Error Checking Table 11. CLRSEL Options section. Output Clear Value • The core temperature of the AD5751 exceeds Unipolar Output approximately 150°C. CLRSEL Voltage Range Unipolar Current Output Range 0 0 V Zero-scale; for example: OUTPUT FAULT ALERT—HARDWARE MODE 4 mA on the 4 mA to 20 mA range 0 mA on the 0 mA to 20 mA In hardware mode, the AD5751 is equipped with three fault pins: 1 Midscale Midscale; for example: VFAULT, IFAULT, and TEMP. These are open-drain outputs 12 mA on the 4 mA to 20 mA range allowing several AD5751 devices to be connected together to 10 mA on the 0 mA to 20 mA range one pull-up resistor for global fault detection. In hardware EXTERNAL CURRENT SETTING RESISTOR control mode, these fault pins are forced active by any one of the following fault scenarios: Referring to Figure 1, RSET is an internal sense resistor and is part of the voltage-to-current conversion circuitry. The nominal • An open-circuit is detected. The voltage at IOUT attempts value of the internal current sense resistor is 15 kΩ. To allow for to rise above the compliance range, due to an open-loop overrange capability in current mode, the user can also select circuit or insufficient power supply voltage. The internal the internal current sense resistor to be 14.7 kΩ, giving a nominal circuitry that develops the fault output avoids using a 2% overrange capability. This feature is available in the 0 mA to comparator with window limits because this requires an 20 mA, 0 mA to 24 mA, and 4 mA to 20 mA current ranges. actual output error before the fault output becomes active. Instead, the signal is generated when the internal amplifier The stability of the output current value over temperature is in the output stage has less than approximately 1 V of dependent on the stability of the value of RSET. As a method of remaining drive capability. Thus, the fault output activates improving the stability of the output current over temperature, slightly before the compliance limit is reached. Because the an external low drift resistor can be connected to the REXT1 comparison is made within the feedback loop of the output and REXT2 pins of the AD5751, which can be used instead of the internal resistor. The external resistor is selected via the amplifier, the output accuracy is maintained by its open- input shift register. If the external resistor option is not used, the loop gain, and an output error does not occur before the fault output becomes active. If this fault is detected, the REXT1 and REXT2 pins should be left floating. IFAULT pin is forced low. Rev. A | Page 27 of 32 AD5751 PROGRAMMABLE OVERRANGE MODES PACKET ERROR CHECKING The AD5751 contains an overrange mode for most of the To verify that data has been received correctly in noisy available ranges. The overranges are selected by configuring the environments, the AD5751 offers the option of error checking R3, R1, R1, and R0 bits (or pins) accordingly. based on an 8-bit (CRC-8) cyclic redundancy check. The device controlling the AD5751 should generate an 8-bit frame check In voltage mode, depending on selected range, the overranges sequence using the following polynomial: are 10% or 20%, providing programmable output ranges of 0 V to 6 V, 0 V to 12 V, and 0 V to 44 V. The 0 V to 4.096 V analog C(x) = x + x + x + 1 8 2 1 input remains the same. This is added to the end of the data-word, and 24 data bits are In current mode, the overranges are typically 2%. In current sent to the AD5751 before taking SYNC high. If the AD5751 mode, the overrange capability is only available on three ranges, receives a 24-bit data frame, it performs the error check when 0 mA to 20 mA, 0 mA to 24 mA, and 4 mA to 20 mA. For these SYNC goes high. If the check is valid, then the data is written to ranges, the analog input also remains the same (0 V to 4.096 V). the selected register. If the error check fails, the FAULT pin goes low and Bit D3 of the status register is set. After reading this register, this error flag is cleared automatically and the FAULT pin goes high again. UPDATE ON SYNC HIGH SYNC SCLK D15 D0 (MSB) (LSB) 16-BIT DATA SDIN 16-BIT DATA TRANSER—NO ERROR CHECKING UPDATE AFTER SYNC HIGH ONLY IF ERROR CHECK PASSED SYNC SCLK D23 D8 (MSB) (LSB) D7 D0 SDIN 16-BIT DATA 8-BIT FCS FAULT GOES LOW IF FAULT ERROR CHECK FAILS 16-BIT DATA TRANSER WITH ERROR CHECKING Figure 54. PEC Error Checking Timing Rev. A | Page 28 of 32 07269-010 AD5751 APPLICATIONS INFORMATION THERMAL CONSIDERATIONS TRANSIENT VOLTAGE PROTECTION It is important to understand the effects of power dissipation The AD5751 contains ESD protection diodes that prevent damage on the package and how it affects junction temperature. The from normal handling. The industrial control environment can, internal junction temperature should not exceed 125°C. The however, subject I/O circuits to much higher transients. To protect AD5751 is packaged in a 32-lead, 5 mm × 5 mm LFCSP pack- the AD5751 from excessively high voltage transients, external age. The thermal impedance, θJA, is 28°C/W. It is important that power diodes and a surge current limiting resistor may be the devices not be operated under conditions that cause the required, as shown in Figure 55. The constraint on the resistor junction temperature to exceed its limit. Worst-case conditions value is that during normal operation the output level at IOUT occur when the AD5751 are operated from the maximum AV DD must remain within its voltage compliance limit of AV − DD (55 V) and driving the maximum current (24 mA) directly to 2.75 V and the two protection diodes and resistor must have ground. The quiescent current of the AD5751 should also be appropriate power ratings. Further protection can be added taken into account, nominally ~4 mA. The following calculations with transient voltage suppressors if needed. estimate maximum power dissipation under these worst-case AV DD conditions, and determine maximum ambient temperature based on this. These figures assume that proper layout and grounding AV DD techniques are followed to minimize power dissipation, as AD5751 R P outlined in the Layout Guidelines section. I OUT R LOAD Figure 55. Output Transient Voltage Protection Table 12. Thermal and Supply Considerations Considerations 32-Lead LFCSP Package Maximum allowed power dissipation when operating at an ambient T −T 125− 85 JMAX A = = 1.42 W temperature of 85°C θ 28 JA Maximum allowed ambient temperature when operating from a supply of TJMAX − (PD × θJA) = 125 − ((55 × 0.028) × 28) = 81.8°C 55 V and driving 24 mA directly to ground (include 4 mA for internal AD5751 current) Maximum allowed supply voltage when operating at an ambient T −T 125− 85 JMAX A = = 51 V temperature of 85°C and driving 24 mA directly to ground AI ×θ() 0.028× 28 DD JA Rev. A | Page 29 of 32 07269-011 AD5751 corresponding thermal land paddle on the PCB (GND). LAYOUT GUIDELINES Thermal vias should be designed into the PCB land paddle area In any circuit where accuracy is important, careful consideration to further improve heat dissipation. of the power supply and ground return layout helps to ensure the rated performance. The PCB on which the AD5751 is GALVANICALLY ISOLATED INTERFACE mounted should be designed so that the AD5751 lies on the In many process control applications, it is necessary to provide analog plane. an isolation barrier between the controller and the unit being The AD5751 should have ample supply bypassing of 10 μF in controlled to protect and isolate the controlling circuitry from parallel with 0.1 μF on each supply, located as close to the any hazardous common-mode voltages that may occur. The package as possible, ideally right up against the device. The iCoupler® family of products from Analog Devices, Inc., provides 10 μF capacitors are the tantalum bead type. The 0.1 μF capaci- voltage isolation in excess of 5.0 kV. The serial loading structure tor should have low effective series resistance (ESR) and low of the AD5751 makes it ideal for isolated interfaces because the effective series inductance (ESI) such as the common ceramic number of interface lines is kept to a minimum. Figure 57 shows a types, which provide a low impedance path to ground at high 4-channel isolated interface to the AD5751 using an ADuM1400. frequencies to handle transient currents due to internal logic For further information, visit http://www.analog.com/icouplers. switching. 1 CONTROLLER ADuM1400 In systems where there are many devices on one board, it is often V V OA IA TO SERIAL ENCODE DECODE SCLK CLOCK OUT useful to provide some heat sinking capability to allow the power to dissipate easily. V V IB OB TO SERIAL ENCODE DECODE SDIN DATA OUT AD5751 V V OC TO IC SYNC OUT ENCODE DECODE SYNC V V OD ID TO CONTROL OUT ENCODE DECODE CLEAR 1 ADDITIONAL PINS OMITTED FOR CLARITY. GND Figure 57. Isolated Interface PLANE MICROPROCESSOR INTERFACING BOARD Microprocessor interfacing to the AD5751 is via a serial bus that uses a protocol compatible with microcontrollers and DSP proces- Figure 56. Paddle Connection to Board sors. The communication channel is a 3-wire (minimum) interface consisting of a clock signal, a data signal, and a SYNC The AD5751 has an exposed paddle beneath the device. signal. The AD5751 requires a 16-bit data-word with data valid Connect this paddle to the GND of the AD5751. For optimum on the falling edge of SCLK. performance, special considerations should be used to design the motherboard and to mount the package. For enhanced thermal, electrical, and board level performance, the exposed paddle on the bottom of the package should be soldered to the Rev. A | Page 30 of 32 07269-012 07269-013 AD5751 OUTLINE DIMENSIONS 5.00 0.60 MAX BSC SQ 0.60 MAX PIN 1 INDICATOR 25 32 1 24 PIN 1 INDICATOR 0.50 BSC TOP EXPOSED 3.25 4.75 VIEW BSC SQ PAD 3.10 SQ (BOTTOM VIEW) 2.95 0.50 0.40 17 8 16 9 0.30 0.25 MIN 0.80 MAX 3.50 REF 12° MAX 0.65 TYP FOR PROPER CONNECTION OF 0.05 MAX THE EXPOSED PAD, REFER TO 1.00 0.02 NOM THE PIN CONFIGURATION AND 0.85 0.30 FUNCTION DESCRIPTIONS COPLANARITY 0.20 REF SECTION OF THIS DATA SHEET. 0.80 0.23 0.08 SEATING 0.18 PLANE COMPLIANT TO JEDEC STANDARDS MO-220-VHHD-2 Figure 58. 32-Lead Lead Frame Chip Scale Package [LFCSP_VQ] 5 mm × 5 mm Body, Very Thin Quad (CP-32-2) Dimensions shown in millimeters ORDERING GUIDE 1 Model Temperature Range Package Description Package Option AD5751ACPZ −40°C to +105°C 32-Lead LFCSP_VQ CP-32-2 AD5751ACPZ-REEL7 −40°C to +105°C 32-Lead LFCSP_VQ CP-32-2 AD5751BCPZ −40°C to +105°C 32-Lead LFCSP_VQ CP-32-2 AD5751BCPZ-REEL7 −40°C to +105°C 32-Lead LFCSP_VQ CP-32-2 1 Z = RoHS Compliant Part. Rev. A | Page 31 of 32 011708-A AD5751 NOTES ©2009-2010 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D07269-0-5/10(A) Rev. A | Page 32 of 32
Frequently asked questions
What makes Elite.Parts unique?
What kind of warranty will the AD5751 have?
Which carriers does Elite.Parts work with?
Will Elite.Parts sell to me even though I live outside the USA?
I have a preferred payment method. Will Elite.Parts accept it?
Why buy from GID?
Quality
We are industry veterans who take pride in our work
Protection
Avoid the dangers of risky trading in the gray market
Access
Our network of suppliers is ready and at your disposal
Savings
Maintain legacy systems to prevent costly downtime
Speed
Time is of the essence, and we are respectful of yours
Manufacturers


What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods