ANALOG DEVICES AD5421
Description
Analog Devices AD5421 16-Bit, Serial Input, Loop-Powered, 4 mA to 20 mA Digital-to-Analog Converter
Part Number
AD5421
Price
Request Quote
Manufacturer
ANALOG DEVICES
Lead Time
Request Quote
Category
PRODUCTS - A
Specifications
DAC Input Format
SPI
DAC Settling Time
50µs
DAC Type
Current Out
Max Pos Supply (V)
+52V
Resolution (Bits)
16bit
Single-Supply
Yes
Features
- 16-bit resolution and monotonicity
- Automatic readback of fault register on each write cycle
- Flexible SPI-compatible serial digital interface with Schmitt triggered inputs
- Gain and offset adjust registers
- INL error: 0.0035% FSR maximum
- Loop voltage range: 5.5 V to 52 V
- NAMUR-compliant alarm currents: Downscale alarm current = 3.2 mA; Upscale alarm current = 22.8 mA/24 mA
- On-chip fault alerts via FAULT pin or alarm current
- On-chip reference TC: 4 ppm/°C maximum
- Output TC: 3 ppm/°C typical
- Pin selectable NAMUR-compliant ranges: 4 mA to 20 mA; 3.8 mA to 21 mA; 3.2 mA to 24 mA
- Quiescent current: 300 µA maximum
- Selectable regulated voltage output
- Slew rate control function
- Temperature range: -40°C to +105°C
- Total unadjusted error (TUE): 0.05% maximum
- TSSOP and LFCSP packages
Datasheet
Extracted Text
16-Bit, Serial Input, Loop-Powered, 4 mA to 20 mA DAC Data Sheet AD5421 FEATURES GENERAL DESCRIPTION 16-bit resolution and monotonicity The AD5421 is a complete, loop-powered, 4 mA to 20 mA Pin selectable NAMUR-compliant ranges digital-to-analog converter (DAC) designed to meet the needs 4 mA to 20 mA of smart transmitter manufacturers in the industrial control 3.8 mA to 21 mA industry. The DAC provides a high precision, fully integrated, 3.2 mA to 24 mA low cost solution in compact TSSOP and LFCSP packages. NAMUR-compliant alarm currents The AD5421 includes a regulated voltage output that is used to Downscale alarm current = 3.2 mA power itself and other devices in the transmitter. This regulator Upscale alarm current = 22.8 mA/24 mA provides a regulated 1.8 V to 12 V output voltage. The AD5421 Total unadjusted error (TUE): 0.05% maximum also contains 1.22 V and 2.5 V references, thus eliminating the INL error: 0.0035% FSR maximum need for a discrete regulator and voltage reference. Output TC: 3 ppm/°C typical The AD5421 can be used with standard HART® FSK protocol Quiescent current: 300 µA maximum communication circuitry without any degradation in specified Flexible SPI-compatible serial digital interface performance. The high speed serial interface is capable of opera- with Schmitt triggered inputs ting at 30 MHz and allows for simple connection to commonly On-chip fault alerts via FAULT pin or alarm current used microprocessors and microcontrollers via a SPI-compatible, Automatic readback of fault register on each write cycle 3-wire interface. Slew rate control function Gain and offset adjust registers The AD5421 is guaranteed monotonic to 16 bits. It provides On-chip reference TC: 4 ppm/°C maximum 0.0015% integral nonlinearity, 0.0012% offset error, and Selectable regulated voltage output 0.0006% gain error under typical conditions. Loop voltage range: 5.5 V to 52 V The AD5421 is available in a 28-lead TSSOP and a 32-lead Temperature range: −40°C to +105°C LFCSP specified over the extended industrial temperature range TSSOP and LFCSP packages of −40°C to +105°C. APPLICATIONS COMPANION PRODUCTS Industrial process control HART Modem: AD5700, AD5700-1 4 mA to 20 mA loop-powered transmitters Smart transmitters HART network connectivity FUNCTIONAL BLOCK DIAGRAM IODV DV V REG_SEL0 REG_SEL1 REG_SEL2 REG REG DD DD LOOP OUT IN LOOP VOLTAGE FAULT DRIVE VOLTAGE REGULATOR MONITOR SYNC INPUT R SET REGISTER SCLK 24kΩ CONTROL SDIN 16 LOGIC 16-BIT SDO DAC GAIN/OFFSET LDAC ADJUSTMENT REGISTERS RANGE0 TEMPERATURE RANGE1 11.5kΩ 52Ω SENSOR LOOP– ALARM_CURRENT_DIRECTION VREF AD5421 R /R INT EXT REFOUT2 REFOUT1 REFIN C R R COM IN EXT1 EXT2 Figure 1. Rev. D Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. rights of third parties that may result from its use. Specifications subject to change without notice. No Tel: 781.329.4700 www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Fax: 781.461.3113 ©2011–2012 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. 09128-001 AD5421 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 On-Chip ADC ............................................................................ 22 Applications ....................................................................................... 1 Voltage Regulator ....................................................................... 22 General Description ......................................................................... 1 Loop Current Slew Rate Control .............................................. 22 Functional Block Diagram .............................................................. 1 Power-On Default ...................................................................... 23 Revision History ............................................................................... 2 HART Communications ........................................................... 23 Specifications ..................................................................................... 3 Serial Interface ................................................................................ 25 AC Performance Characteristics ................................................ 8 Input Shift Register .................................................................... 25 Timing Characteristics ................................................................ 8 Register Readback ...................................................................... 25 Absolute Maximum Ratings .......................................................... 10 DAC Register .............................................................................. 26 Thermal Resistance .................................................................... 10 Control Register ......................................................................... 27 ESD Caution ................................................................................ 10 Fault Register .............................................................................. 28 Pin Configuration and Function Descriptions ........................... 11 Offset Adjust Register ................................................................ 29 Typical Performance Characteristics ........................................... 13 Gain Adjust Register .................................................................. 29 Terminology .................................................................................... 19 Applications Information .............................................................. 31 Theory of Operation ...................................................................... 20 Determining the Expected Total Error ................................... 31 Fault Alerts .................................................................................. 20 Thermal and Supply Considerations ....................................... 32 External Current Setting Resistor ............................................ 21 Outline Dimensions ....................................................................... 33 Loop Current Range Selection .................................................. 21 Ordering Guide .......................................................................... 34 Connection to Loop Power Supply .......................................... 21 REVISION HISTORY 5/12—Rev. C to Rev. D Changes to Figure 33 ...................................................................... 17 Changes to Features Section and Applications Section; Added Changes to the On-Chip ADC Section ....................................... 22 Companion Products Section ......................................................... 1 Changes to Figure 46 ...................................................................... 23 Changes to Line Regulation Parameter, Table 1 ........................... 5 Changes to Figure 48 ...................................................................... 24 Updated Outline Dimensions ....................................................... 33 Changes to the Register Readback Section ................................. 25 Updated Outline Dimensions ....................................................... 33 12/11—Rev. B to Rev. C Changes to Ordering Guide .......................................................... 34 Change to REFOUT1 Pin, Capacitive Load Parameter, Test Conditions, Table 1 ........................................................................... 4 5/11—Rev. 0 to Rev. A Change to REGOUT Output, Capacitive Load Parameter, Test Changes to REGIN, REFOUT1, and REFOUT2 Pin Descriptions Conditions, Table 1 ........................................................................... 5 in Table 8 .......................................................................................... 10 Changes to ESD Parameter, Table 6 ............................................. 10 Change to Figure 45 ....................................................................... 22 Changes to Input Shift Register Section, Table 11, and Register 12/11—Rev. A to Rev. B Readback Section ............................................................................ 24 Added 32-Lead LFCSP ....................................................... Universal Changes to Figure 48 ...................................................................... 30 Changes to the Specifications Section, Table 1 ............................. 3 Changes to Table 7 .......................................................................... 10 2/11—Revision 0: Initial Version Added Figure 5, Renumbered Sequentially ................................ 11 Changes to Table 8 .......................................................................... 11 Rev. D | Page 2 of 36 Data Sheet AD5421 SPECIFICATIONS Loop voltage = 24 V; REFIN = 2.5 V external; RL = 250 Ω; external NMOS connected; all loop current ranges; all specifications TMIN to TMAX, unless otherwise noted. Table 1. 1 Parameter Min Typ Max Unit Test Conditions/Comments ACCURACY, INTERNAL R SET Resolution 16 Bits 2 Total Unadjusted Error (TUE) −0.126 +0.126 % FSR C grade −0.041 ±0.0064 +0.041 % FSR C grade, TA = 25°C −0.18 +0.18 % FSR B grade −0.06 ±0.011 +0.06 % FSR B grade, T = 25°C A −0.27 +0.27 % FSR A grade −0.08 ±0.011 +0.08 A grade, TA = 25°C TUE Long-Term Stability 210 ppm FSR Drift after 1000 hours at TA = 125°C Relative Accuracy (INL) −0.0035 ±0.0015 +0.0035 % FSR C grade −0.012 ±0.006 +0.012 % FSR B grade −0.024 ±0.01 +0.024 % FSR A grade Differential Nonlinearity (DNL) −1 +1 LSB Guaranteed monotonic Offset Error −0.056 +0.056 % FSR B grade and C grade −0.008 ±0.0008 +0.008 % FSR B grade and C grade, TA = 25°C −0.11 ±0.0008 +0.11 % FSR A grade 3 Offset Error TC 1 ppm FSR/°C Gain Error −0.107 +0.107 % FSR B grade and C grade −0.035 ±0.0058 +0.035 % FSR B grade and C grade, TA = 25°C −0.2 ±0.0058 +0.2 % FSR A grade 3 Gain Error TC 4 ppm FSR/°C Full-Scale Error −0.126 +0.126 % FSR B grade and C grade −0.041 ±0.0065 +0.041 % FSR B grade and C grade, T = 25°C A −0.25 ±0.0065 +0.25 % FSR A grade 3 Full-Scale Error TC 5 ppm FSR/°C Downscale Alarm Current 3.19 3.21 mA Upscale Alarm Current 22.77 22.83 mA 4 mA to 20 mA and 3.8 mA to 21 mA ranges 23.97 24.03 mA 3.2 mA to 24 mA range ACCURACY, EXTERNAL R (24 kΩ) Assumes ideal resistor, B grade and SET C grade only; not specified for A grade Resolution 16 Bits 2 Total Unadjusted Error (TUE) −0.048 +0.048 % FSR C grade −0.027 ±0.002 +0.027 % FSR C grade, TA = 25°C −0.08 +0.08 % FSR B grade −0.04 ±0.003 +0.04 % FSR B grade, T = 25°C A TUE Long-Term Stability 40 ppm FSR Drift after 1000 hours at T = 125°C A Relative Accuracy (INL) −0.0035 ±0.0015 +0.0035 % FSR C grade −0.012 ±0.006 +0.012 % FSR B grade Differential Nonlinearity (DNL) −1 +1 LSB Guaranteed monotonic Offset Error −0.021 +0.021 % FSR −0.007 ±0.0012 +0.007 % FSR T = 25°C A 3 Offset Error TC 0.5 ppm FSR/°C Gain Error −0.03 +0.03 % FSR −0.023 ±0.0006 +0.023 % FSR TA = 25°C Rev. D | Page 3 of 36 AD5421 Data Sheet 1 Parameter Min Typ Max Unit Test Conditions/Comments 3 Gain Error TC 1 ppm FSR/°C Full-Scale Error −0.047 +0.047 % FSR −0.028 ±0.0017 +0.028 % FSR TA = 25°C 3 Full-Scale Error TC 1 ppm FSR/°C Downscale Alarm Current 3.08 3.21 mA Upscale Alarm Current 22.78 23 mA 4 mA to 20 mA and 3.8 mA to 21 mA ranges 23.99 24.01 mA 3.2 mA to 24 mA range 3 OUTPUT CHARACTERISTICS 4 Loop Compliance Voltage LOOP− + 5.5 V REGOUT < 5.5 V, loop current = 24 mA LOOP− + 12.5 V REGOUT = 12 V, loop current = 24 mA Loop Current Long-Term Stability 100 ppm FSR Drift after 1000 hours at T = 125°C, A loop current = 12 mA, internal R SET 15 ppm FSR Drift after 1000 hours at T = 125°C, A loop current = 12 mA, external RSET Loop Current Error vs. REGOUT Load 1.2 µA/mA Loop current = 12 mA, load current Current from REGOUT = 5 mA Resistive Load 0 2 kΩ See Figure 20 for a load line graph Inductive Load 50 mH Stable operation Power Supply Sensitivity 0.1 µA/V Loop current = 12 mA Output Impedance 12 400 MΩ Output TC 3 ppm FSR/°C Loop current = 12 mA, internal RSET 1 ppm FSR/°C Loop current = 12 mA, external RSET Output Noise 0.1 Hz to 10 Hz 50 nA p-p 500 Hz to 10 kHz 0.2 mV rms HART bandwidth; measured across 500 Ω load Noise Spectral Density 195 nA/√Hz At 1 kHz 256 nA/√Hz At 10 kHz 3 REFERENCE INPUT (REFIN PIN) 5 Reference Input Voltage 2.5 V For specified performance DC Input Impedance 75 800 MΩ REFERENCE OUTPUTS REFOUT1 Pin Output Voltage 2.498 2.5 2.503 V T = 25°C A Temperature Coefficient 1.5 4 ppm/°C C grade 2 8 ppm/°C B grade 4 10 ppm/°C A grade 3 Output Noise (0.1 Hz to 10 Hz) 7.5 µV p-p 3 Noise Spectral Density 245 nV/√Hz At 1 kHz 70 nV/√Hz At 10 kHz 3 Output Voltage Drift vs. Time 200 ppm Drift after 1000 hours at T = 125°C A 3 Capacitive Load 10 nF Recommended operation 3, 6 Load Current 4 mA 3 Short-Circuit Current 6.5 mA Short circuit to COM 3 Power Supply Sensitivity 2 12 µV/V 3 Thermal Hysteresis 285 ppm First temperature cycle 5 ppm Second temperature cycle 3 Load Regulation 0.1 0.2 mV/mA Measured at 0 mA and 1 mA loads Output Impedance 0.1 Ω REFOUT2 Pin Output Voltage 1.18 1.227 1.28 V T = 25°C A Output Impedance 72 kΩ Rev. D | Page 4 of 36 Data Sheet AD5421 1 Parameter Min Typ Max Unit Test Conditions/Comments REGOUT OUTPUT Voltage regulator output Output Voltage 1.8 12 V See Table 10 3 Output Voltage TC 110 ppm/°C Output Voltage Accuracy −4 ±2 +4 % 3, 6 Externally Available Current 3.15 mA Assuming 4 mA flowing in the loop and during HART communications Short-Circuit Current 23 mA 3 Line Regulation 500 μV/V Internal NMOS 10 μV/V External NMOS 3 Load Regulation 8 mV/mA Inductive Load 50 mH Stable operation Capacitive Load 2 10 µF Recommended operation ADC ACCURACY Die Temperature ±5 °C VLOOP Input ±1 % DV OUTPUT Can be overdriven up to 5.5 V DD Output Voltage 3.17 3.3 3.48 V 3, 6 Externally Available Current 3.15 mA Assuming 4 mA flowing in the loop and during HART communications Short-Circuit Current 7.7 mA Load Regulation 45 mV/mA Measured at 0 mA and 3 mA loads 3 DIGITAL INPUTS SCLK, SYNC, SDIN, LDAC Input High Voltage, VIH 0.7 × IODVDD V Input Low Voltage, V 0.25 × IODV V IL DD Hysteresis 0.21 V IODV = 1.8 V DD 0.63 V IODVDD = 3.3 V 1.46 V IODVDD = 5.5 V Input Current −0.015 +0.015 µA Per pin Pin Capacitance 5 pF Per pin 3 DIGITAL OUTPUTS SDO Pin Output Low Voltage, V 0.4 V OL Output High Voltage, V IODV − 0.5 V OH DD High Impedance Leakage −0.01 +0.01 µA Current High Impedance Output 5 pF Capacitance FAULT Pin Output Low Voltage, V 0.4 V OL Output High Voltage, VOH IODVDD − 0.5 V FAULT THRESHOLDS I Under I − 0.01% FSR mA LOOP LOOP ILOOP Over ILOOP + 0.01% FSR mA Temp 140°C 133 °C Fault removed when temperature ≤ 125°C Temp 100°C 90 °C Fault removed when temperature ≤ 85°C V 6V 0.3 V Fault removed when V ≥ 0.4 V LOOP LOOP VLOOP 12V 0.6 V Fault removed when VLOOP ≥ 0.7 V Rev. D | Page 5 of 36 AD5421 Data Sheet 1 Parameter Min Typ Max Unit Test Conditions/Comments POWER REQUIREMENTS REGIN 5.5 52 V With respect to LOOP− IODVDD 1.71 5.5 V With respect to COM Quiescent Current 260 300 µA 1 Temperature range: −40°C to +105°C; typical at +25°C. 2 Total unadjusted error is the total measured error (offset error + gain error + linearity error + output drift over temperature) after factory calibration of the AD5421. System level total error can be reduced using the offset and gain registers. 3 Guaranteed by design and characterization; not production tested. 4 The voltage between LOOP− and REGIN must be 5.5 V or greater. 5 The AD5421 is factory calibrated with an external 2.5 V reference connected to REFIN. 6 This is the current that the output is capable of sourcing. The load current originates from the loop and, therefore, contributes to the total current consumption figure. Rev. D | Page 6 of 36 Data Sheet AD5421 Loop voltage = 24 V; REFIN = REFOUT1 (2.5 V internal reference); R = 250 Ω; external NMOS connected; all loop current ranges; L all specifications T to T , unless otherwise noted. MIN MAX Table 2. C Grade 1, 2 Parameter Min Typ Max Unit Test Conditions/Comments ACCURACY, INTERNAL R SET 3 Total Unadjusted Error (TUE) −0.157 +0.157 % FSR −0.117 ±0.0172 +0.117 % FSR TA = 25°C Relative Accuracy (INL) −0.004 +0.004 % FSR −0.004 ±0.0015 +0.004 % FSR TA = 25°C Offset Error −0.04 +0.04 % FSR −0.025 ±0.0025 +0.025 % FSR T = 25°C A Offset Error TC 1 ppm FSR/°C Gain Error −0.128 +0.128 % FSR −0.093 ±0.0137 +0.093 % FSR TA = 25°C Gain Error TC 5 ppm FSR/°C Full-Scale Error −0.157 +0.157 % FSR −0.117 ±0.0172 +0.117 % FSR T = 25°C A Full-Scale Error TC 6 ppm FSR/°C ACCURACY, EXTERNAL R (24 kΩ) Assumes ideal resistor SET 3 Total Unadjusted Error (TUE) −0.133 +0.133 % FSR −0.133 ±0.0252 +0.133 % FSR TA = 25°C Relative Accuracy (INL) −0.004 +0.004 % FSR −0.004 ±0.0015 +0.004 % FSR TA = 25°C Offset Error −0.029 +0.029 % FSR −0.029 ±0.0038 +0.029 % FSR T = 25°C A Offset Error TC 0.5 ppm FSR/°C Gain Error −0.11 +0.11 % FSR −0.106 ±0.0197 +0.106 % FSR TA = 25°C Gain Error TC 2 ppm FSR/°C Full-Scale Error −0.133 +0.133 % FSR −0.133 ±0.0252 +0.133 % FSR T = 25°C A Full-Scale Error TC 2 ppm FSR/°C 1 Temperature range: −40°C to +105°C; typical at +25°C. 2 Specifications guaranteed by design and characterization; not production tested. 3 Total unadjusted error is the total measured error (offset error + gain error + linearity error + output drift over temperature) after factory calibration of the AD5421. System level total error can be reduced using the offset and gain registers. Rev. D | Page 7 of 36 AD5421 Data Sheet AC PERFORMANCE CHARACTERISTICS Loop voltage = 24 V; REFIN = 2.5 V external; RL = 250 Ω; all specifications TMIN to TMAX, unless otherwise noted. Table 3. 1 Parameter Min Typ Max Unit Test Conditions/Comments DYNAMIC PERFORMANCE Loop Current Settling Time 50 µs To 0.1% FSR, CIN = open circuit Loop Current Slew Rate 400 µA/µs CIN = open circuit AC Loop Voltage Sensitivity 1.3 µA/V 1200 Hz to 2200 Hz, 5 V p-p, RL = 3 kΩ 1 Temperature range: −40°C to +105°C; typical at +25°C. TIMING CHARACTERISTICS Loop voltage = 24 V; REFIN = 2.5 V external; R = 250 Ω; all specifications T to T . L MIN MAX Table 4. 1, 2, 3 Parameter Limit at T , T Unit Description MIN MAX t1 33 ns min SCLK cycle time t 17 ns min SCLK high time 2 t 17 ns min SCLK low time 3 t4 17 ns min SYNC falling edge to SCLK falling edge setup time t5 10 ns min SCLK falling edge to SYNC rising edge t6 25 µs min Minimum SYNC high time t 5 ns min Data setup time 7 t 5 ns min Data hold time 8 t 25 µs min SYNC rising edge to LDAC falling edge 9 t10 10 ns min LDAC pulse width low t11 70 ns max SCLK rising edge to SDO valid (CL SDO = 30 pF) t12 0 ns min SYNC falling edge to SCLK rising edge setup time t 70 ns max SYNC rising edge to SDO tristate (C = 30 pF) 13 L SDO 1 Guaranteed by design and characterization; not production tested. 2 All input signals are specified with tR = tF = 5 ns (10% to 90% of DVDD) and timed from a voltage level of 1.2 V. 3 See Figure 2 and Figure 3. Table 5. SPI Watchdog Timeout Periods 1 Parameter T0 T1 T2 Min Typ Max Unit 0 0 0 43 50 59 ms 0 0 1 87 100 117 ms 0 1 0 436 500 582 ms 0 1 1 873 1000 1163 ms 1 0 0 1746 2000 2326 ms 1 0 1 2619 3000 3489 ms 1 1 0 3493 4000 4652 ms 1 1 1 4366 5000 5814 ms 1 Specifications guaranteed by design and characterization; not production tested. Rev. D | Page 8 of 36 Data Sheet AD5421 Timing Diagrams t 1 t 12 SCLK 1 8 9 10 11 12 22 24 2 23 t t 3 2 SDIN D23 D16 D15 D14 D13 D2 D1 D0 t t 8 13 t t 4 7 D15 D14 D13 D2 D1 D0 SDO t 6 t 5 t 11 SYNC t t 9 10 LDAC Figure 2. Serial Interface Timing Diagram SCLK 1 8 9 24 1 8 9 24 SDIN D23 D16 D15 D0 D23 D16 D15 D0 INPUT WORD SPECIFIES REGISTER TO BE READ NOP OR REGISTER ADDRESS SDO D15 D0 UNDEFINED DATA SPECIFIED REGISTER DATA CLOCKED OUT SYNC Figure 3. Readback Timing Diagram Rev. D | Page 9 of 36 09128-002 09128-003 AD5421 Data Sheet ABSOLUTE MAXIMUM RATINGS TA = 25°C, unless otherwise noted. Transient currents of up Stresses above those listed under Absolute Maximum Ratings to 100 mA do not cause SCR latch-up. may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any Table 6. other conditions above those indicated in the operational Parameter Rating section of this specification is not implied. Exposure to absolute REG to COM −0.3 V to +60 V IN maximum rating conditions for extended periods may affect REGOUT to COM −0.3 V to +14 V device reliability. Digital Inputs to COM, −0.3 V to DVDD + 0.3 V RANGE0, RANGE1, RINT/REXT, or +7 V (whichever is less) THERMAL RESISTANCE ALARM_CURRENT_DIRECTION, θJA is specified for the worst-case conditions, that is, a device REG_SEL0, REG_SEL1, REG_SEL2 soldered in a circuit board for surface-mount packages. Digital Inputs to COM −0.3 V to IODVDD + 0.3 V SCLK, SDIN, SYNC, LDAC or +7 V (whichever is less) Table 7. Thermal Resistance Digital Outputs to COM, −0.3 V to IODVDD + 0.3 V Package Type θ θ Unit JA JC SDO, FAULT or +7 V (whichever is less) 28-Lead TSSOP_EP (RE-28-2) 32 9 °C/W REFIN to COM −0.3 V to +7 V 24-Lead LFCSP_WQ (CP-32-11) 40 7 °C/W REFOUT1, REFOUT2 −0.3 V to +4.7 V VLOOP to COM −0.3 V to +60 V LOOP− to COM −5 V to +0.3 V ESD CAUTION DVDD to COM −0.3 V to +7 V IODV to COM −0.3 V to +7 V DD R , C to COM −0.3 V to +4.3 V EXT1 IN R to COM −0.3 V to +0.3 V EXT2 DRIVE to COM −0.3 V to +11 V Operating Temperature Range (TA) Industrial −40°C to +105°C Storage Temperature Range −65°C to +150°C Junction Temperature (T ) 125°C J MAX Power Dissipation (T − T )/θ J MAX A JA Lead Temperature, JEDEC Industry Standard Soldering (10 sec) J-STD-020 ESD Human Body Model 3 kV Field Induced Charged Device 2 kV Model Machine Model 200 V Rev. D | Page 10 of 36 Data Sheet AD5421 PIN CONFIGURATION AND FUNCTION DESCRIPTIONS 1 28 IODV REG DD OUT 2 27 SDO REG IN 3 26 SCLK DRIVE 4 25 SYNC V LOOP 5 AD5421 24 SDIN LOOP– SDIN 1 24 V LOOP PIN 1 TOP VIEW 6 23 LDAC 2 23 LOOP– LDAC R INDICATOR EXT2 (Not to Scale) FAULT 3 22 R EXT2 FAULT 7 22 R EXT1 AD5421 COM 4 21 R EXT1 DV 8 21 C DD IN DV 5 TOP VIEW 20 C DD IN ALARM_CURRENT_DIRECTION 9 20 REFOUT1 (Not to Scale) ALARM CURRENT DIRECTION 6 19 REFOUT1 R /R 10 19 REFOUT2 R /R 7 18 REFOUT2 INT EXT INT EXT RANGE 0 8 17 REFIN 11 18 REFIN RANGE0 12 17 RANGE1 REG_SEL0 13 16 COM REG_SEL1 14 15 COM REG_SEL2 NOTES 1. THE EXPOSED PADDLE SHOULD BE CONNECTED TO THE SAME POTENTIAL AS THE COM PIN AND TO A COPPER PLANE FOR NOTES OPTIMUM THERMAL PERFORMANCE. 1. NO CONNECT. DO NOT CONNECT TO THIS PIN. 2. THE EXPOSED PADDLE SHOULD BE CONNECTED TO THE SAME POTENTIAL AS THE COM PIN AND TO A COPPER PLANE FOR OPTIMUM THERMAL PERFORMANCE. Figure 4. TSSOP Pin Configuration Figure 5. LFCSP Pin Configuration Table 8. Pin Function Descriptions Pin No. TSSOP LFCSP Mnemonic Description 1 29 IODVDD Digital Interface Supply Pin. Digital thresholds are referenced to the voltage applied to this pin. A voltage from 1.71 V to 5.5 V can be applied to this pin. 2 30 SDO Serial Data Output. Used to clock data from the input shift register. Data is clocked out on the rising edge of SCLK and is valid on the falling edge of SCLK. 3 31 SCLK Serial Clock Input. Data is clocked into the input shift register on the falling edge of SCLK. This input operates at clock speeds up to 30 MHz. 4 32 SYNC Frame Synchronization Input, Active Low. This is the frame synchronization signal for the serial interface. When SYNC is low, data is transferred on the falling edge of SCLK. The input shift register data is latched on the rising edge of SYNC. 5 1 SDIN Serial Data Input. Data must be valid on the falling edge of SCLK. 6 2 LDAC Load DAC Input, Active Low. This pin is used to update the DAC register and, consequently, the output current. If LDAC is tied permanently low, the DAC register is updated on the rising edge of SYNC. If LDAC is held high during the write cycle, the input register is updated, but the output update is delayed until the falling edge of LDAC. The LDAC pin should not be left unconnected. 7 3 FAULT Fault Alert Output Pin, Active High. This pin is asserted high when a fault is detected. Detectable faults are loss of SPI interface control, communication error (PEC), loop current out of range, insufficient loop voltage, and overtemperature. For more information, see the Fault Alerts section. 8 5 DV 3.3 V Digital Power Supply Output. This pin should be decoupled to COM with 100 nF and 4.7 µF DD capacitors. 9 6 ALARM_ Alarm Current Direction Select. This pin is used to select whether the alarm current is upscale CURRENT_ (22.8 mA/24 mA) or downscale (3.2 mA). Connecting this pin to DVDD selects an upscale alarm DIRECTION current (22.8 mA/24 mA); connecting this pin to COM selects a downscale alarm current (3.2 mA). For more information, see the Power-On Default section. 10 7 R /R Current Setting Resistor Select. When this pin is connected to DV , the internal current setting INT EXT DD resistor is selected. When this pin is connected to COM, the external current setting resistor is selected. An external resistor can be connected between the REXT1 and REXT2 pins. 11, 12 8, 10 RANGE0, Digital Input Pins. These two pins select the loop current range (see the Loop Current Range RANGE1 Selection section). Rev. D | Page 11 of 36 09128-004 09128-100 NC 9 32 SYNC RANGE 1 10 31 SCLK COM 11 30 SDO COM 12 29 IODV DD REG_SEL2 13 28 REG OUT REG_SEL1 14 27 REG IN REG_SEL0 15 26 DRIVE NC 16 25 NC AD5421 Data Sheet Pin No. TSSOP LFCSP Mnemonic Description 13, 14 4, 11, 12 COM Ground Reference Pin for the AD5421. It is recommended that a 4.7 V Zener diode be placed between the LOOP− and COM pins. See the Applications Information section for more information. 15, 16, 13, 14, 15 REG_SEL2, These three pins together select the regulator output (REGOUT) voltage (see the Voltage Regulator 17 REG_SEL1, section). REG_SEL0 18 17 REFIN Reference Voltage Input. V = 2.5 V for specified performance. REFIN 19 18 REFOUT2 Internal Reference Voltage Output (1.22 V). It is recommended to connect a 100 nF capacitor from this pin to COM. 20 19 REFOUT1 Internal Reference Voltage Output (2.5 V). It is recommended to connect a 100 nF capacitor from this pin to COM. 21 20 C External Capacitor Connection and HART FSK Input. An external capacitor connected from C to IN IN COM implements an output slew rate control function (see the Loop Current Slew Rate Control section). HART FSK signaling can also be coupled through a capacitor to this pin (see the HART Communications section). 22, 23 21, 22 R , R Connection for External Current Setting Resistor. A precision 24 kΩ resistor can be connected EXT1 EXT2 between these pins for improved performance. 24 23 LOOP− Loop Current Return Pin. 25 23 VLOOP Voltage Input Pin. Voltage input range is 0 V to 2.5 V. The voltage applied to this pin is digitized to eight bits, which are available in the fault register. This pin can be used for general-purpose voltage monitoring, but it is intended for monitoring of the loop supply voltage. Connecting the loop voltage to this pin via a 20:1 resistor divider allows the AD5421 to monitor and feedback the loop voltage. The AD5421 also generates an alert if the loop voltage is close to the minimum operating value (see the Loop Voltage Fault section). 26 26 DRIVE Gate Connection for External Depletion Mode MOSFET. For more information, see the Connection to Loop Power Supply section. 27 27 REG Voltage Regulator Input. The loop voltage can be connected directly to this pin. Or, to reduce on- IN chip power dissipation, an external pass transistor can be connected at this pin to stand off the loop voltage. For more information, see the Connection to Loop Power Supply section. 28 28 REGOUT Voltage Regulator Output. Pin selectable values are from 1.8 V to 12 V via the REG_SEL0, REG_SEL1, and REG_SEL2 pins (see the Voltage Regulator section). 1 N/A 9, 16, 25 NC No Connect. Do not connect to this pin. EPAD EPAD Exposed Pad The exposed paddle should be connected to the same potential as the COM pin and to a copper plane for optimum thermal performance. 1 N/A means not applicable. Rev. D | Page 12 of 36 Data Sheet AD5421 TYPICAL PERFORMANCE CHARACTERISTICS 1.0 0.015 EXT V , INT R REF SET EXT V , EXT R 0.8 REF SET INT V , INT R REF SET 0.6 0.010 INT V , EXT R REF SET 0.4 0.2 0.005 0 –0.2 0 V = 24V LOOP –0.4 EXT NMOS R = 250Ω LOAD –0.6 –0.005 T = 25°C V = 24V A LOOP 4mA TO 20mA RANGE 4mA TO 20mA RANGE –0.8 EXT V R = 250Ω LOAD REF EXT R EXT NMOS SET –1.0 –0.010 0 10k 20k 30k 40k 50k 60k –40 –15 10 35 60 85 DAC CODE TEMPERATURE (°C) Figure 6. Integral Nonlinearity Error vs. Code Figure 9. Offset Error vs. Temperature 1.0 0.03 0.8 0.02 0.6 0.01 0.4 0 0.2 –0.01 0 –0.02 V = 24V LOOP –0.2 4mA TO 20mA RANGE R = 250Ω V = 24V –0.03 LOOP LOAD –0.4 EXT NMOS EXT NMOS R = 250Ω LOAD –0.04 EXT V , INT R REF SET –0.6 T = 25°C A EXT V , EXT R REF SET 4mA TO 20mA RANGE –0.05 –0.8 INT V , INT R REF SET EXT V REF INT V , EXT R EXT R SET REF SET –1.0 –0.06 0 10k 20k 30k 40k 50k 60k –40 –15 10 35 60 85 DAC CODE TEMPERATURE (°C) Figure 7. Differential Nonlinearity Error vs. Code Figure 10. Gain Error vs. Temperature 0.01 0.0012 R = 250Ω LOAD T = 25°C A 0.0010 4mA TO 20mA RANGE 0 MAX INL 0.0008 –0.01 0.0006 0.0004 –0.02 0.0002 EXT V , INT R REF SET V = 24V –0.03 LOOP EXT V , EXT R REF SET 0 4mA TO 20mA RANGE INT V , INT R REF SET R = 250Ω LOAD V EXT, R EXT, NMOS EXT, 24V INT V , EXT R REF SET –0.0002 REF SET –0.04 V EXT, R EXT, NMOS INT, 24V REF SET V EXT, R EXT, NMOS INT, 52V –0.0004 REF SET V INT, R INT, NMOS EXT, 24V –0.05 MIN INL REF SET –0.0006 V INT, R INT, NMOS INT, 24V REF SET V INT, R INT, NMOS INT, 52V REF SET –0.06 –0.0008 0 10k 20k 30k 40k 50k 60k –40 –15 10 35 60 85 DAC CODE TEMPERATURE (°C) Figure 8. Total Unadjusted Error vs. Code Figure 11. Integral Nonlinearity Error vs. Temperature Rev. D | Page 13 of 36 TOTAL UNADJUSTED ERROR (% FSR) DNL ERROR (LSB) INL ERROR (LSB) 09128-006 09128-005 09128-007 INL ERROR (% FSR) GAIN ERROR (% FSR) OFFSET ERROR (% FSR) 09128-009 09128-008 09128-010 AD5421 Data Sheet 0.5 0.0006 MAX INL 0.4 0.0004 0.3 MAX DNL 0.2 0.0002 V = 24V 0.1 LOOP 4mA TO 20mA RANGE R = 250Ω 0 LOAD 0 –0.1 MIN INL –0.0002 MIN DNL –0.2 R = 250Ω LOAD –0.3 T = 25°C A –0.0004 3.8mA TO 21mA RANGE –0.4 EXT V REF EXT R SET –0.5 –0.0006 –40 –15 10 35 60 85 0 10 20 30 40 50 60 TEMPERATURE (°C) LOOP SUPPLY VOLTAGE (V) Figure 12. Differential Nonlinearity Error vs. Temperature Figure 15. Integral Nonlinearity Error vs. Loop Supply Voltage 0.04 0.0029 0.03 0.0027 0.02 0.0025 0.01 0 0.0023 –0.01 V = 24V LOOP 0.0021 –0.02 4mA TO 20mA RANGE R = 250Ω LOAD –0.03 EXT NMOS 0.0019 R = 250Ω LOAD EXT V , INT R REF SET –0.04 T = 25°C A EXT V , EXT R REF SET 0.0017 3.8mA TO 21mA RANGE INT V , INT R –0.05 REF SET EXT V REF INT V , EXT R REF SET EXT R SET –0.06 0.0015 –40 –15 10 35 60 85 0 10 20 30 40 50 60 TEMPERATURE (°C) LOOP SUPPLY VOLTAGE (V) Figure 13. Total Unadjusted Error vs. Temperature Figure 16. Total Unadjusted Error vs. Loop Supply Voltage 0.04 0.0024 R = 250Ω LOAD T = 25°C A 0.03 3.8mA TO 21mA RANGE 0.0022 EXT V REF 0.02 EXT R SET 0.0020 0.01 0 0.0018 –0.01 V = 24V LOOP 0.0016 –0.02 4mA TO 20mA RANGE R = 250Ω LOAD –0.03 EXT NMOS 0.0014 EXT V , INT R REF SET –0.04 EXT V , EXT R REF SET 0.0012 INT V , INT R –0.05 REF SET INT V , EXT R REF SET –0.06 0.0010 –40 –15 10 35 60 85 0 10 20 30 40 50 60 TEMPERATURE (°C) LOOP SUPPLY VOLTAGE (V) Figure 14. Full-Scale Error vs. Temperature Figure 17. Offset Error vs. Loop Supply Voltage Rev. D | Page 14 of 36 FULL-SCALE ERROR (% FSR) TOTAL UNADJUSTED ERROR (% FSR) DNL ERROR (LSB) 09128-011 09128-013 09128-012 OFFSET ERROR (% FSR) TOTAL UNADJUSTED ERROR (% FSR) INL ERROR (% FSR) 09128-016 09128-015 09128-014 Data Sheet AD5421 0.0015 4.70 R = 250Ω R = 250Ω LOAD LOAD T = 25°C 3.2mA TO 24mA RANGE A 0.0010 3.8mA TO 21mA RANGE EXT V 4.65 REF EXT V I = 24mA REF LOOP EXT R 0.0005 SET 4.60 0 4.55 –0.0005 4.50 –0.0010 4.45 –0.0015 4.40 –0.0020 –0.0025 4.35 0 10 20 30 40 50 60 –40 –20 0 20 40 60 80 100 LOOP SUPPLY VOLTAGE (V) TEMPERATURE (°C) Figure 18. Gain Error vs. Loop Supply Voltage Figure 21. Compliance Voltage Headroom vs. Temperature 0.0030 7 V = 24V LOOP EXT NMOS R = 250Ω 0.0025 6 LOAD T = 25°C A I = 20mA LOOP 0.0020 5 0.0015 4 0.0010 3 0.0005 2 R = 250Ω LOAD T = 25°C A 0 3.8mA TO 21mA RANGE 1 EXT V REF EXT R SET –0.0005 0 0 10 20 30 40 50 60 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 LOOP SUPPLY VOLTAGE (V) REG LOAD CURRENT (mA) OUT Figure 19. Full-Scale Error vs. Loop Supply Voltage Figure 22. Loop Current Error vs. REG Load Current OUT 2000 8 T = 25°C A EXT V REF 1750 6 I = 24mA LOOP EXT R SET 1500 4 2 1250 1000 0 750 –2 OPERATING AREA V = 24V LOOP 500 –4 EXT NMOS EXT V REF I = 4mA 250 –6 LOOP R = 250Ω LOAD T = 25°C A 0 –8 0 10 20 30 40 50 0 1 2 3 4 5 6 7 8 9 10 LOOP SUPPLY VOLTAGE (V) TIME (Seconds) Figure 20. Load Resistance Load Line vs. Loop Supply Voltage Figure 23. Loop Current Noise, 0.1 Hz to 10 Hz Bandwidth (Voltage Between LOOP− and REGIN) Rev. D | Page 15 of 36 FULL-SCALE ERROR (% FSR) GAIN ERROR (% FSR) LOAD RESISTANCE (Ω) 09128-019 09128-018 09128-017 COMPLIANCE VOLTAGE HEADROOM (V) VOLTAGE ACROSS 250Ω LOAD RESISTOR (µV) LOOP CURRENT ERROR (µA) 09128-022 09128-021 09128-020 AD5421 Data Sheet 1.0 0.244 V = 24V I = 4mA 1.33mV p-p LOOP LOOP IODV = 1.8V DD EXT NMOS R = 500Ω 0.2mV rms 0.8 LOAD T = 25°C A 0.242 INT V T = 25°C REF A 0.6 0.240 DECREASING 0.4 0.238 0.2 0.236 0 0.234 –0.2 0.232 –0.4 INCREASING 0.230 –0.6 0.228 –0.8 –1.0 0.226 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 0 0.5 1.0 1.5 2.0 TIME (Seconds) DIGITAL LOGIC VOLTAGE (V) Figure 24. Loop Current Noise, 500 Hz to 10 kHz Bandwidth Figure 27. IODVDD Current vs. Digital Logic Voltage, Increasing and (HART Bandwidth) Decreasing, IODVDD = 1.8 V 6 0.60 IODV = 3.3V DD T = 25°C FALLING A 5 0.55 DECREASING 4 INCREASING V = 24V LOOP EXT NMOS R = 250Ω 3 0.50 LOAD T = 25°C A C = OPEN CIRCUIT IN 2 0.45 RISING 1 0 0.40 –40 –30 –20 –10 0 10 20 30 40 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 TIME (µs) DIGITAL LOGIC VOLTAGE (V) Figure 25. Full-Scale Loop Current Step Figure 28. IODVDD Current vs. Digital Logic Voltage, Increasing and Decreasing, IODVDD = 3.3 V 6 1.3 IODV = 5V DD T = 25°C A FALLING 1.2 5 DECREASING 1.1 4 V = 24V LOOP 1.0 EXT NMOS INCREASING R = 250Ω 3 LOAD T = 25°C A 0.9 C = 22nF IN 2 0.8 RISING 1 0.7 0 0.6 –1.0 –0.5 0 0.5 1.0 1.5 2.0 2.5 3.0 0 1 2 3 4 5 6 TIME (ms) DIGITAL LOGIC VOLTAGE (V) Figure 26. Full-Scale Loop Current Step, C = 22 nF Figure 29. IODV Current vs. Digital Logic Voltage, Increasing and IN DD Decreasing, IODV = 5 V DD Rev. D | Page 16 of 36 VOLTAGE ACROSS 500Ω LOAD RESISTOR (mV) VOLTAGE ACROSS 250Ω LOAD RESISTOR (V) VOLTAGE ACROSS 250Ω LOAD RESISTOR (V) 09128-026 09128-025 09128-023 IODV CURRENT (µA) IODV CURRENT (µA) DD IODV CURRENT (µA) DD DD 09128-029 09128-028 09128-027 Data Sheet AD5421 3.5 0 REG LOAD CURRENT (mA) OUT 0 0.05 0.10 0.15 0.20 0.25 1.85 0 3.0 V = 24V LOOP –50 EXT NMOS –5 1.84 T = 25°C A 2.5 –10 1.83 –100 –15 2.0 1.82 –20 1.81 1.5 –150 –25 1.80 –30 1.0 1.79 –200 –35 0.5 V = 24V LOOP 1.78 EXT NMOS –40 T = 25°C A 0 –250 1.77 –45 0 1 2 3 4 5 DV LOAD CURRENT (mA) 1.76 –50 DD 0 2 4 6 8 10 12 REG LOAD CURRENT (mA) OUT Figure 30. REGOUT Voltage vs. Load Current Figure 33. DVDD Output Voltage vs. Load Current 263.5 4 T = 25°C A 263.0 3 262.5 2 262.0 1 261.5 261.0 0 260.5 –1 260.0 –2 259.5 V = 24V LOOP –3 259.0 EXT NMOS T = 25°C A 258.5 –4 0 10 20 30 40 50 60 0 1 2 3 4 5 6 7 8 9 10 LOOP SUPPLY VOLTAGE (V) TIME (Seconds) Figure 31. Quiescent Current vs. Loop Supply Voltage Figure 34. REFOUT1 Voltage Noise, 0.1 Hz to 10 Hz Bandwidth 266 3.0 1 V = 24V LOOP EXT NMOS 265 V = IODV IH DD 2.5 0 V = COM IL 264 T = 25°C A 263 –1 2.0 262 –2 1.5 261 260 –3 1.0 259 0.5 –4 V = 24V LOOP 258 EXT NMOS T = 25°C A 257 0 –5 –40 –20 0 20 40 60 80 100 0 1 2 3 4 5 6 7 TEMPERATURE (°C) REFOUT1 LOAD CURRENT (mA) Figure 32. Quiescent Current vs. Temperature Figure 35. REFOUT1 Voltage vs. Load Current Rev. D | Page 17 of 36 REG VOLTAGE (V) OUT QUIESCENT CURRENT (µA) QUIESCENT CURRENT (µA) REG VOLTAGE CHANGE (mV) 09128-032 OUT 09128-031 09128-030 REFOUT1 VOLTAGE (V) DV OUTPUT VOLTAGE (V) DD REFOUT1 VOLTAGE NOISE (µV) REFOUT1 VOLTAGE CHANGE (mV) 09128-034 DV OUTPUT VOLTAGE CHANGE (mV) DD 09128-101 09128-035 AD5421 Data Sheet 2.5012 250 60 DEVICES SHOWN V = 24V LOOP EXT NMOS 2.5010 R = 250Ω LOAD I = 3.2mA 200 LOOP 2.5008 2.5006 150 2.5004 2.5002 100 2.5000 2.4998 50 2.4996 2.4994 0 –40 –20 0 20 40 60 80 100 –40 –20 0 20 40 60 80 100 TEMPERATURE (°C) DIE TEMPERATURE (°C) Figure 36. REFOUT1 Voltage vs. Temperature, 60 Devices Shown Figure 38. On-Chip ADC Code vs. Die Temperature (C Grade Device) 30 250 V = 24V MEAN TC = 1.5ppm/°C LOOP EXT NMOS T = 25°C A 25 200 20 150 15 100 10 50 5 0 0 0 0.5 1.0 1.5 2.0 2.5 V PIN INPUT VOLTAGE (V) LOOP TEMPERATURE COEFFICIENT (ppm/°C) Figure 37. REFOUT1 Temperature Coefficient Histogram Figure 39. On-Chip ADC Code vs. VLOOP Pin Input Voltage (C Grade Device) Rev. D | Page 18 of 36 REFOUT1 VOLTAGE (V) POPULATION (%) 0 0.25 0.50 0.75 1.00 1.25 1.50 1.75 2.00 2.25 2.50 2.75 3.00 3.25 3.50 3.75 4.00 4.25 4.50 4.75 5.00 09128-037 09128-036 ADC CODE (Decimal) ADC CODE (Decimal) 09128-038 09128-039 Data Sheet AD5421 TERMINOLOGY Loop Compliance Voltage Headroom Total Unadjusted Error Total unadjusted error (TUE) is a measure of the total output Loop compliance voltage headroom is the minimum voltage error. TUE consists of INL error, offset error, gain error, and between the LOOP− and REGIN pins for which the output output drift over temperature, in the case of maximum TUE. current is equal to the programmed value. TUE is expressed in % FSR. Output Temperature Coefficient (TC) Relative Accuracy or Integral Nonlinearity (INL) Error Output TC is a measure of the change in the output current Relative accuracy, or integral nonlinearity (INL) error, is a at 12 mA with changes in temperature and is expressed in measure of the maximum deviation in the output current from ppm FSR/°C. a straight line passing through the endpoints of the transfer Voltage Reference Thermal Hysteresis function. INL error is expressed in % FSR. Voltage reference thermal hysteresis is the difference in output Differential Nonlinearity (DNL) Error voltage measured at +25°C compared to the output voltage Differential nonlinearity (DNL) error is the difference between measured at +25°C after cycling the temperature from +25°C to the measured change and the ideal 1 LSB change between any −40°C to +105°C and back to +25°C. The hysteresis is specified two adjacent codes. A specified differential nonlinearity of for the first and second temperature cycles and is expressed in mV. ±1 LSB maximum ensures monotonicity. Voltage Reference Temperature Coefficient (TC) Offset Error Voltage reference TC is a measure of the change in the reference Offset error is a measure of the output error when zero code is output voltage with a change in temperature. The voltage refer- loaded to the DAC register and is expressed in % FSR. ence TC is calculated using the box method, which defines the TC as the maximum change in the reference output voltage over Offset Error Temperature Coefficient (TC) a given temperature range. Voltage reference TC is expressed in Offset error TC is a measure of the change in offset error with ppm/°C as follows: changes in temperature and is expressed in ppm FSR/°C. V − V Gain Error REF_MAX REF_MIN 6 TC = × 10 Gain error is a measure of the span error of the DAC. It is the V × Temp_Range REF_NOM deviation in slope of the DAC transfer function from the ideal where: and is expressed in % FSR. V is the maximum reference output voltage measured REF_MAX Gain Error Temperature Coefficient (TC) over the total temperature range. Gain error TC is a measure of the change in gain error with VREF_MIN is the minimum reference output voltage measured changes in temperature and is expressed in ppm FSR/°C. over the total temperature range. Full-Scale Error VREF_NOM is the nominal reference output voltage, 2.5 V. Full-scale error is a measure of the output error when full-scale Temp_Range is the specified temperature range code is loaded to the DAC register and is expressed in % FSR. (−40°C to +105°C). Full-Scale Error Temperature Coefficient (TC) Full-scale error TC is a measure of the change in full-scale error with changes in temperature and is expressed in ppm FSR/°C. Rev. D | Page 19 of 36 AD5421 Data Sheet THEORY OF OPERATION The AD5421 is an integrated device designed for use in loop- In the case of data readback, if the AD5421 is addressed with a powered, 4 mA to 20 mA smart transmitter applications. In a 32-bit frame, it generates the 8-bit frame check sequence and single chip, the AD5421 provides a 16-bit DAC and current appends it to the end of the 24-bit data stream to create a 32-bit amplifier for digital control of the loop current, a voltage data stream. regulator to power the entire transmitter, a voltage reference, fault alert functions, a flexible SPI-compatible serial interface, UPDATE ON SYNC HIGH SYNC gain and offset adjust registers, as well as other features and functions. The features of the AD5421 are described in the following sections. SCLK MSB LSB D23 D0 FAULT ALERTS SDIN 24-BIT DATA The AD5421 provides a number of fault alert features. All faults are signaled to the controller via the FAULT pin and the 24-BIT DATA TRANSFER—NO ERROR CHECKING fault register. In the case of a loss of communication between UPDATE AFTER SYNC HIGH the AD5421 and the microcontroller (SPI fault), the AD5421 ONLY IF ERROR CHECK PASSED SYNC programs the loop current to an alarm value. If the controller detects that the FAULT pin is set high, it should then read the fault register to determine the cause of the fault. SCLK MSB LSB SPI Fault D31 D8 D7 D0 SDIN 24-BIT DATA 8-BIT FCS The SPI fault is asserted if there is no valid communication to any register of the AD5421 for more than a user-defined period. FAULT PIN GOES HIGH The user can program the time period using the SPI watchdog FAULT IF ERROR CHECK FAILS timeout bits of the control register. The SPI fault bit of the fault 32-BIT DATA TRANSFER WITH ERROR CHECKING register indicates the fault on the SPI bus. Because this fault is Figure 40. PEC Timing caused by a loss of communication between the controller and Current Loop Fault the AD5421, the loop current is also forced to the alarm value. The current loop (I ) fault is asserted when the actual loop LOOP The direction of the alarm current (downscale or upscale) current is not within ±0.01% FSR of the programmed loop is selected via the ALARM_CURRENT_DIRECTION pin. current. If the measured loop current is less than the programmed Connecting this pin to DVDD selects an upscale alarm current loop current, the ILOOP Under bit of the fault register is set. If the (22.8 mA/24 mA); connecting this pin to COM selects a measured loop current is greater than the programmed loop downscale alarm current (3.2 mA). current, the I Over bit of the fault register is set. The FAULT LOOP Packet Error Checking pin is set to logic high in either case. To verify that data has been received correctly in noisy environ- An I Over condition occurs when the value of the load current LOOP ments, the AD5421 offers the option of error checking based on sourced from the AD5421 (via REG , REFOUT1, REFOUT2, OUT an 8-bit cyclic redundancy check (CRC). Packet error checking or DVDD) is greater than the loop current that is programmed (PEC) is enabled by writing to the AD5421 with a 32-bit serial to flow in the loop. An ILOOP under condition occurs when there frame, where the least significant eight bits are the frame check is insufficient compliance voltage to support the programmed sequence (FCS). The device controlling the AD5421 should loop current, caused by excessive load resistance or low loop generate the 8-bit FCS using the following polynomial: supply voltage. 8 2 C(x) = x + x + x + 1 Overtemperature Fault The 8-bit FCS is appended to the end of the data-word, and There are two overtemperature alert bits in the fault register: 32 data bits are sent to the AD5421 before SYNC is taken high. Temp 100°C and Temp 140°C. If the die temperature of the AD5421 exceeds either 100°C or 140°C, the appropriate bit is If the check is valid, the data is accepted. If the check fails, the set. If the Temp 140°C bit is set in the fault register, the FAULT FAULT pin is asserted and the PEC bit of the fault register is set. pin is set to logic high. After the fault register is read, the PEC bit is reset low and the FAULT pin returns low. Rev. D | Page 20 of 36 09128-049 Data Sheet AD5421 Loop Voltage Fault LOOP CURRENT RANGE SELECTION There are two loop voltage alert bits in the fault register: To select the loop current range, connect the RANGE0 VLOOP 12V and VLOOP 6V. If the voltage between the VLOOP and and RANGE1 pins to the COM and DVDD pins, as shown COM pins falls below 0.6 V (corresponding to a 12 V loop in Table 9. supply value), the VLOOP 12V bit is set; this bit is cleared when Table 9. Selecting the Loop Current Range the voltage returns above 0.7 V. Similarly, if the voltage between RANGE1 Pin RANGE0 Pin Loop Current Range the V and COM pins falls below 0.3 V (corresponding to a LOOP COM COM 4 mA to 20 mA 6 V loop supply value), the V 6V bit is set; this bit is cleared LOOP COM DVDD 3.8 mA to 21 mA when the voltage returns above 0.4 V. If the V 6V bit is set in LOOP DV COM 3.2 mA to 24 mA DD the fault register, the FAULT pin is set to logic high. DV DV 3.8 mA to 21 mA DD DD Figure 41 illustrates how a resistor divider enables the monitor- ing of the loop supply with the VLOOP input. The recommended CONNECTION TO LOOP POWER SUPPLY resistor divider consists of a 1 MΩ and a 19 MΩ resistor that The AD5421 is powered from the 4 mA to 20 mA current loop. provide a 20:1 ratio, allowing the 2.5 V input range of the V LOOP Typically, the power supply is located far from the transmitter pin to monitor loop supplies up to 50 V. With a 20:1 divider ratio, device and has a value of 24 V. The AD5421 can be connected the preset V 6V and V 12V alert bits of the fault register LOOP LOOP directly to the loop power supply and can tolerate a voltage up generate loop supply faults according to their stated values. If to a maximum of 52 V (see Figure 42). another divider ratio is used, the fault bits generate faults at values that are not equal to 6 V and 12 V. REG IN V LOOP AD5421 REG IN DRIVE R AD5421 V L 19MΩ LOOP V LOOP– LOOP R L 1MΩ COM LOOP– COM Figure 42. Direct Connection of the AD5421 to Loop Power Supply Figure 42 shows how the AD5421 is connected directly to the loop power supply. An alternative power connection is shown Figure 41. Resistor Divider Connection at V Pin LOOP in Figure 43, which shows a depletion mode N-channel MOSFET EXTERNAL CURRENT SETTING RESISTOR connected between the AD5421 and the loop power supply. The The 24 kΩ resistor RSET, shown in Figure 1, converts the DAC use of this device keeps the voltage drop across the AD5421 at output voltage to a current, which is then mirrored with a gain approximately 12 V, limiting the worst-case on-chip power dissi- of 221 to the LOOP− pin. The stability of the loop current over pation to 288 mW (12 V × 24 mA = 288 mW). If the AD5421 is temperature is dependent on the temperature coefficient of R . SET connected directly to the loop supply as shown in Figure 42, the potential worst-case on-chip power dissipation for a 24 V loop Table 1 and Table 2 outline the performance specifications of power supply is 576 mW (24 V × 24 mA = 576 mW). The power the AD5421 with both the internal R resistor and an external, SET dissipation changes in proportion to the loop power supply voltage. 24 kΩ RSET resistor. Using the internal RSET resistor, a total unad- justed error of better than 0.126% FSR can be expected. Using T1 DN2540 BSP129 an external resistor gives improved performance of 0.048% FSR. This specification assumes an ideal resistor; the actual performance 200kΩ depends on the absolute value and temperature coefficient of REG IN the resistor used. For more information, see the Determining V LOOP AD5421 the Expected Total Error section. DRIVE R L LOOP– COM Figure 43. MOSFET Connecting the AD5421 to Loop Power Supply Rev. D | Page 21 of 36 09128-048 09128-050 09128-051 AD5421 Data Sheet The resistance of the DAC is typically 15.22 kΩ for the 4 mA ON-CHIP ADC to 20 mA and 3.8 mA to 21 mA loop current ranges. The DAC The AD5421 contains an on-chip ADC used to measure and resistance changes to 16.11 kΩ when the 3.2 mA to 24 mA loop feed back to the fault register either the temperature of the die current range is selected. or the voltage between the VLOOP and COM pins. The select ADC input bit (Bit D8) of the control register selects the parameter The time constant of the circuit is expressed as to be converted. A conversion is initiated with command byte τ = RDAC × CSLEW 00001000 (necessary only if auto fault readback is disabled). This Taking five time constants as the required time to reach the final command byte powers on the ADC and performs the conversion. value, C can be determined for a desired response time, t, SLEW A read of the fault register returns the conversion result. If auto as follows: readback of the fault register is required, the ADC must first be powered up by setting the on-chip ADC bit (Bit D7) of the t C = SLEW control register. 5× R DAC Because the FAULT pin can go high for as long as 30 μs, care is where: required when performing a die temperature measurement after t is the desired time for the output current to reach its final a readback of the V voltage. LOOP value. RDAC is the resistance of the DAC core, either 15.22 kΩ or VOLTAGE REGULATOR 16.11 kΩ, depending on the selected loop current range. The on-chip voltage regulator provides a regulated voltage out- For a response time of 5 ms, put to supply the AD5421 and the remainder of the transmitter circuitry. The output voltage range is from 1.8 V to 12 V and is 5 ms C = ≈ 68 nF selected by the states of three digital input pins (see Table 10). SLEW 5× 15,220 The regulator output is accessed at the REGOUT pin. For a response time of 10 ms, Table 10. Setting the Voltage Regulator Output 10 ms Regulated Output C = ≈ 133 nF SLEW 5× 15,220 REG_SEL2 REG_SEL1 REG_SEL0 Voltage (V) COM COM COM 1.8 The responses for both of these configurations are shown COM COM DVDD 2.5 in Figure 45. COM DV COM 3.0 DD 6 C = 68nF COM DV DV 3.3 DD DD SLEW DV COM COM 5.0 DD 5 DVDD COM DVDD 9.0 DVDD DVDD COM 12.0 4 C = 267nF SLEW C = 133nF SLEW LOOP CURRENT SLEW RATE CONTROL 3 The rate of change of the loop current can be controlled by 2 connecting an external capacitor between the CIN pin and COM. This reduces the rate of change of the loop current. 1 The output resistance of the DAC (RDAC) together with the C capacitor generate a time constant that determines the SLEW 0 response of the loop current (see Figure 44). –2 2 6 10 14 18 22 TIME (ms) R DAC V-TO-I LOOP– CIRCUITRY Figure 45. 4 mA to 20 mA Step with Slew Rate Control C IN C The CIN pin can also be used as a coupling input for HART SLEW FSK signaling. The HART signal must be ac-coupled to the CIN Figure 44. Slew Capacitor Circuit input. The capacitor through which the HART signal is coupled must be considered in the preceding calculations, where the total capacitance is C + C . For more information, see SLEW HART the HART Communications section. Rev. D | Page 22 of 36 09128-052 VOLTAGE ACROSS 250Ω LOAD RESISTOR (V) 09128-053 Data Sheet AD5421 To achieve a 500 Hz high-pass 3 dB frequency cutoff, the com- POWER-ON DEFAULT bined values of C and C should be 21 nF. To ensure the HART SLEW The AD5421 powers on with all registers loaded with their default correct HART signal amplitude on the current loop, the final values and with the loop current in the alarm state set to 3.2 mA values for the capacitors are C = 4.7 nF and C = 16.3 nF. HART SLEW or 22.8 mA/24 mA (depending on the state of the ALARM_ CURRENT_DIRECTION pin and the selected range). The Output Noise During Silence and Analog Rate of Change AD5421 remains in this state until it is programmed with new The AD5421 has a direct influence on two important specifi- values. The SPI watchdog timer is enabled by default with a cations relating to the HART communications protocol: output timeout period of 1 sec. If there is no communication with the noise during silence and analog rate of change. Figure 24 shows AD5421 within 1 sec of power-on, the FAULT pin is set. the measurement of the AD5421 output noise in the HART extended bandwidth; the noise measurement is 0.2 mV rms, HART COMMUNICATIONS within the required 2.2 mV rms value. The AD5421 can be interfaced to a Highway Addressable To meet the analog rate of change specification, the rate of Remote Transducer (HART) modem to enable HART digital change of the 4 mA to 20 mA current must be slow enough so communications over the 2-wire loop connection. Figure 46 that it does not interfere with the HART digital signaling. This shows how the modem frequency shift keying (FSK) output is is determined by forcing a full-scale loop current change connected to the AD5421. through a 500 Ω load resistor and applying the resulting voltage signal to the HART digital filter (HCF_TOOL-31). The peak amplitude of the signal at the filter output must be less than 200kΩ 150 mV. To achieve this, the rate of change of the loop current must be restricted to less than approximately 1.3 mA/ms. REG IN V LOOP AD5421 The output of the AD5421 naturally slews at approximately DRIVE 880 mA/ms, a rate that is far too great to comply with the R L HART specifications. To reduce the slew rate, a capacitor can be LOOP– connected from the C pin to COM, as described in the Loop C COM IN IN Current Slew Rate Control section. To reduce the slew rate enough so that the HART specification is met, a capacitor value C C SLEW HART in the region of 4.7 μF is required, resulting in a full-scale transition HART time of 500 ms. Many applications regard this time as too slow, MODEM HART_OUT in which case the slew rate needs to be digitally controlled by HART_IN writing a sequence of codes to the DAC register so that the output response follows the desired curve. Figure 46. Connecting a HART Modem to the AD5421 Figure 47 shows a digitally controlled full-scale step and the To achieve a 1 mA p-p FSK current signal on the loop, the voltage resulting filter output. In Figure 47, it can be seen that the peak at the C pin must be 111 mV p-p. Assuming a 500 mV p-p IN amplitude of the filter output signal is less than the required output from the HART modem, this means that the signal must 150 mV, and the transition time is approximately 30 ms. be attenuated by a factor of 4.5. The following equation can be 12 150 used to calculate the values of the CHART and CSLEW capacitors. C C HART SLEW 10 100 4.5 C HART 50 8 From this equation, the ratio of CHART to CSLEW is 1 to 3.5. This ratio of the capacitor values sets the amplitude of the HART 0 6 FSK signal on the loop. The absolute values of the capacitors set the response time of the loop current, as well as the bandwidth –50 4 presented to the HART signal connected at the C pin. The IN bandwidth must pass frequencies from 500 Hz to 10 kHz. The –100 2 , form a high- two capacitors and the internal impedance, RDAC pass filter. The 3 dB frequency of this high-pass filter should be –150 0 –50 –30 –10 10 30 50 less than 500 Hz and can be calculated as follows: TIME (ms) 1 Figure 47. Digitally Controlled Full-Scale Step and Resulting HART Digital f 3dB Filter Output Signal 2R C C DAC HART SLEW Rev. D | Page 23 of 36 09128-054 VOLTAGE ACROSS 500Ω LOAD RESISTOR (V) OUTPUT OF HART DIGITAL FILTER (mV) HCF_TOOL-31 09128-060 AD5421 Data Sheet Figure 48 shows the circuit diagram for this measurement. The 47 nF and 168 nF capacitor values for C and C provide HART SLEW adequate filtering of the digital steps, ensuring that they do not cause interference. REG IN V LOOP AD5421 R L LOOP– C COM IN 168nF 47nF FROM HART MODEM Figure 48. Circuit Diagram for Figure 47 Rev. D | Page 24 of 36 09128-061 Data Sheet AD5421 SERIAL INTERFACE The AD5421 is controlled by a versatile, 3-wire serial interface Address/Command Byte Function that operates at clock rates up to 30 MHz. It is compatible with 00000011 Write to offset adjust register the SPI, QSPI™, MICROWIRE®, and DSP standards. Figure 2 00000100 Write to gain adjust register shows the timing diagram. The interface operates with either 00000101 Load DAC a continuous or noncontinuous gated burst clock. 00000110 Force alarm current 00000111 Reset (it is recommended to wait SYNC The write sequence begins with a falling edge of the 50 µs after a device reset before signal; data is clocked in on the SDIN data line on the falling writing the next command) SYNC edge of SCLK. On the rising edge of , the 24 bits of data 00001000 Initiate V /temperature LOOP are latched; the data is transferred to the addressed register and measurement the programmed function is executed (either a change in DAC 00001001 No operation output or mode of operation). 10000001 Read DAC register 10000010 Read control register If packet error checking on the SPI interface is required using 10000011 Read offset adjust register cyclic redundancy codes, an additional eight bits must be written 10000100 Read gain adjust register to the AD5421, creating a 32-bit serial interface. In this case, 10000101 Read fault register SYNC 32 bits are written to the AD5421 before is brought high. The 16 bits of the data-word written following a load DAC, force INPUT SHIFT REGISTER alarm current, reset, initiate V /temperature measurement, LOOP The input shift register is 24 bits wide (32 bits wide if CRC error or no operation command byte are don’t cares (see Table 12 and checking of the data is required). Data is loaded into the device Table 13). MSB first as a 24-/32-bit word under the control of a serial clock REGISTER READBACK input, SCLK. The input shift register consists of an 8-bit address/ command byte, a 16-bit data-word, and an optional 8-bit CRC, To read back a register, Bit D11 of the control register must be set as shown in Table 12 and Table 13. to Logic 1 to disable the automatic readback of the fault register. The 16 bits of the data-word written following a read command The address/command byte decoding is described in Table 11. are don’t cares (see Table 12 and Table 13). Table 11. Address/Command Byte Functions The register data addressed by the read command is clocked out Address/Command Byte Function of SDO on the subsequent write command (see Figure 3). 00000001 Write to DAC register 00000010 Write to control register Table 12. Input Shift Register MSB LSB D23 D22 D21 D20 D19 D18 D17 D16 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 Address/command byte Data-word Table 13. Input Shift Register with CRC MSB LSB D31 D30 D29 D28 D27 D26 D25 D24 D23 D22 D21 D20 D19 D18 D17 D16 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 Address/command byte Data-word CRC Rev. D | Page 25 of 36 AD5421 Data Sheet For the 3.8 mA to 21 mA output range, the loop current can be DAC REGISTER expressed as follows: The DAC register is a read/write register and is addressed as described in Table 11. The data programmed to the DAC 17.2 mA I = × D + 3.8 mA LOOP 16 register determines the loop current, as shown in the Ideal 2 Output Transfer Function section and in Table 15. For the 3.2 mA to 24 mA output range, the loop current can be Ideal Output Transfer Function expressed as follows: The transfer function describing the relationship between the 20.8 mA I = × D + 3.2 mA data programmed to the DAC register and the loop current is LOOP 16 2 expressed by the following three equations. where D is the decimal value of the DAC register. For the 4 mA to 20 mA output range, the loop current can be expressed as follows: 16 mA I = × D + 4 mA LOOP 16 2 Table 14. DAC Register Bit Map MSB LSB D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 16-bit data Table 15. Relationship of DAC Register Code to Ideal Loop Current (Gain = 65,536; Offset = 0) Ideal Loop Current (mA) DAC Register Code 4 mA to 20 mA Range 3.8 mA to 21 mA Range 3.2 mA to 24 mA Range 0x0000 4 3.8 3.2 0x0001 4.00024 3.80026 3.2003 … … … … 0x7FFF 11.9997 12.39974 13.5997 0x8000 12 12.4 13.6 … … … … 0xFFFE 19.9995 20.99947 23.9994 0xFFFF 19.9997 20.99974 23.9997 Rev. D | Page 26 of 36 Data Sheet AD5421 CONTROL REGISTER The control register is a read/write register and is addressed as described in Table 11. The data programmed to the control register determines the mode of operation of the AD5421. Table 16. Control Register Bit Map MSB LSB D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 SPI watchdog timeout SPI Auto fault Alarm on Set min Select On-chip Power down VLOOP Reserved watchdog readback SPI fault loop ADC ADC internal fault T0 T1 T2 timer current input reference alert Table 17. Control Register Bit Descriptions Control Bits Description SPI watchdog The T0, T1, and T2 bits allow the user to program the watchdog timeout period. The watchdog timer is reset when a valid timeout write to any AD5421 register occurs or when a NOP command is written. T0 T1 T2 Timeout Period 0 0 0 50 ms 0 0 1 100 ms 0 1 0 500 ms 0 1 1 1 sec (default) 1 0 0 2 sec 1 0 1 3 sec 1 1 0 4 sec 1 1 1 5 sec SPI watchdog 0 = SPI watchdog timer is enabled (default). timer 1 = SPI watchdog timer is disabled. Auto fault This bit specifies whether the fault register contents are automatically clocked out on the SDO pin on each write operation. readback (The fault register can always be addressed for readback.) 0 = fault register contents are clocked out on the SDO pin (default). 1 = fault register contents are not clocked out on the SDO pin. Alarm on SPI This bit specifies whether the loop current is forced to the alarm value when an SPI fault is detected (that is, the watchdog fault timer times out). When an SPI fault is detected, the SPI fault bit of the fault register and the FAULT pin are always set. 0 = loop current is forced to the alarm value when an SPI fault is detected (default). 1 = loop current is not forced to the alarm value when an SPI fault is detected. Set min loop 0 = normal operation (default). current 1 = loop current is set to its minimum value so that the total current flowing in the loop consists only of the operating current of the AD5421 and its associated circuitry. Select ADC 0 = on-chip ADC measures the voltage between the V and COM pins (default). LOOP input 1 = on-chip ADC measures the temperature of the AD5421 die. On-chip ADC 0 = on-chip ADC is disabled (default). 1 = on-chip ADC is enabled. Power down 0 = internal voltage reference is powered up (default). internal 1 = internal voltage reference is powered down and an external voltage reference source is required. reference VLOOP fault This bit specifies whether the FAULT pin is set when the voltage between the VLOOP and COM pins falls to approximately 0.3 V. alert (The V 6V bit of the fault register is always set.) LOOP 0 = FAULT pin is not set when the V − COM voltage falls to approximately 0.3 V. LOOP 1 = FAULT pin is set when the V − COM voltage falls to approximately 0.3 V. LOOP Rev. D | Page 27 of 36 AD5421 Data Sheet FAULT REGISTER The read-only fault register is addressed as described in Table 11. The bits in the fault register indicate a range of possible fault conditions. Table 18. Fault Register Bit Map MSB LSB D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 SPI PEC ILOOP ILOOP Temp Temp VLOOP VLOOP VLOOP/temperature value Over Under 140°C 100°C 6V 12V Table 19. Fault Register Bit Descriptions FAULT Fault Alert Pin Set Description SPI Yes This bit is set high to indicate the loss of the SPI interface signaling. This fault occurs if there is no valid communication to the AD5421 over the SPI interface for more than the user-defined timeout period. The occurrence of this fault also forces the loop current to the alarm value if Bit D10 of the control register is at Logic 0. The alarm current direction is determined by the state of the ALARM_CURRENT_DIRECTION pin. PEC (packet Yes This bit is set high when an error in the SPI communication is detected using cyclic redundancy check (CRC) error check) error detection. See the Packet Error Checking section for more information. I Over Yes This bit is set high when the actual loop current is greater than the programmed loop current. LOOP ILOOP Under Yes This bit is set high when the actual loop current is less than the programmed loop current. Temp 140°C Yes This bit is set high to indicate an overtemperature fault. This bit is set if the die temperature of the AD5421 exceeds approximately 140°C. This bit is cleared when the temperature returns below approximately 125°C. Temp 100°C No This bit is set high to indicate an increasing temperature of the AD5421. This bit is set if the die temperature of the AD5421 exceeds approximately 100°C. This bit is cleared when the temperature returns below approximately 85°C. V 6V Yes This bit is set high when the voltage between the V and COM pins falls below approximately 0.3 V (representing LOOP LOOP a 6 V loop supply voltage with 20:1 resistor divider connected at V ). This bit is cleared when the voltage returns LOOP above approximately 0.4 V. V 12V No This bit is set high when the voltage between the V and COM pins falls below approximately 0.6 V (representing LOOP LOOP a 12 V loop supply voltage with 20:1 resistor divider connected at V ). This bit is cleared when the voltage returns LOOP above approximately 0.7 V. V /temper- N/A These eight bits represent either the voltage between the V and COM pins or the AD5421 die temperature, LOOP LOOP ature value depending on the setting of Bit D8 of the control register (see the On-Chip ADC Transfer Function Equations section). 8-Bit Value V − COM Voltage (V) Die Temperature (°C) LOOP 00000000 0 +300 … … … 11111111 2.49 −55 On-Chip ADC Transfer Function Equations The transfer function equation for the die temperature is as follows: The transfer function equation for the measurement of the voltage between the VLOOP and COM pins is as follows: Die Temperature = 125 − (1.771 × (D − 128)) V − COM = (2.5/256) × D LOOP where D is the 8-bit digital code returned by the on-chip ADC. where D is the 8-bit digital code returned by the on-chip ADC. Rev. D | Page 28 of 36 Data Sheet AD5421 OFFSET ADJUST REGISTER The offset adjust register is a read/write register and is addressed as described in Table 11. Table 20. Offset Adjust Register Bit Map MSB LSB D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 16-bit offset adjust data Table 21. Offset Adjust Register Adjustment Range Offset Adjust Register Data Digital Offset Adjustment (LSBs) 65535 +32767 65534 +32766 … … 32769 +1 32768 (default) 0 32767 −1 … … 1 −32767 0 −32768 GAIN ADJUST REGISTER The gain adjust register is a read/write register and is addressed as described in Table 11. Table 22. Gain Adjust Register Bit Map MSB LSB D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 16-bit gain adjust data Table 23. Gain Adjust Register Adjustment Range Gain Adjust Register Data Digital Gain Adjustment at Full-Scale Output (LSBs) 65535 (default) 0 65534 −1 … … 32769 −32767 32768 −32768 32767 −32769 … … 1 −65534 0 −65535 Rev. D | Page 29 of 36 AD5421 Data Sheet Transfer Function Equations with Offset and Gain Adjust For the 3.2 mA to 24 mA output range, the loop current can be Values expressed as follows: When the offset adjust and gain adjust register values are taken 20.8 mA × Gain into account, the transfer equations can be expressed as follows. 16 2 I = × D LOOP For the 4 mA to 20 mA output range, the loop current can be 16 2 expressed as follows: 16 mA × Gain 20.8 mA 16 2 + 3.2 mA+ ×(Offset − 32,768) 16 I = × D LOOP 16 2 2 where: D is the decimal value of the DAC register. 16 mA Gain is the decimal value of the gain adjust register. + 4 mA+ ×(Offset − 32,768) 16 2 Offset is the decimal value of the offset adjust register. Note that the offset adjust register cannot adjust the zero-scale output value downward. For the 3.8 mA to 21 mA output range, the loop current can be expressed as follows: 17.2 mA × Gain 16 2 I = × D LOOP 16 2 17.2 mA + 3.8 mA+ ×(Offset − 32,768) 16 2 Rev. D | Page 30 of 36 Data Sheet AD5421 APPLICATIONS INFORMATION Figure 49 shows a typical connection diagram for the AD5421 DETERMINING THE EXPECTED TOTAL ERROR configured in a HART capable smart transmitter. To reduce The AD5421 can be set up in a number of different configu- power dissipation on the chip, a depletion mode MOSFET (T1), rations, each of which achieves different levels of accuracy, as such as a DN2540 or BSP129, can be connected between the described in Table 1 and Table 2. With the internal voltage loop voltage and the AD5421, as shown in Figure 49. reference and internal RSET enabled, a maximum total error If a low loop voltage is used, T1 does not need to be inserted, of 0.157% of full-scale range can be expected for the C grade and the loop voltage can connect directly to REG (see Figure 42). IN device over the temperature range of −40°C to +105°C. In Figure 49, all interface signal lines are connected to the micro- Other configurations specify an external voltage reference, an controller. To reduce the number of interface signal lines, the external R resistor, or both an external voltage reference and SET LDAC signal can be connected to COM, and the SDO and FAULT external R resistor. In these configurations, the specifications SET lines can be left unconnected. However, this configuration disables assume that the external voltage reference and external R SET the use of the fault alert features. resistor are ideal. Therefore, the errors associated with these Under normal operating conditions, the voltage between COM components must be added to the data sheet specifications to and LOOP− does not exceed 1.5 V, and the voltage at LOOP− is determine the overall performance. The performance depends negative with respect to COM. If it is possible that the voltage at on the specifications of these components. LOOP− may be forced positive with respect to COM, or if the voltage difference between LOOP− and COM may be forced in excess of 5 V, a 4.7 V low leakage Zener diode should be placed between COM and the LOOP− pin, as shown in Figure 49, to protect the AD5421 from potential damage. OPTIONAL OPTIONAL 2.5V T1 EMC FILTER MOSFET DN2540 BSP129 10µF 4.7µF 200kΩ 0.1µF 0.1µF IODV DV REG REG DD DD OUT IN V LOOP RANGE0 RANGE1 DRIVE 19MΩ R L ALARM_CURRENT_DIRECTION V LOOP R /R INT EXT 1MΩ SYNC ADuC7060 SCLK LOOP– AD5421 SDIN V = 4.7V Z SDO R EXT1 24-BIT FAULT SENSOR MCU R1 Σ-Δ ADC LDAC R EXT2 OPTIONAL COM RESISTOR REFOUT2 C REFOUT1 REFIN IN COM 0.1µF SETS REGULATOR 0.1µF VOLTAGE 0.1µF 47nF 168nF V CC HART MODEM TxD RxD HART_OUT RTS CD HART_IN GND Figure 49. AD5421 Application Diagram for HART Capable Smart Transmitter Rev. D | Page 31 of 36 REG_SEL0 REG_SEL1 REG_SEL2 09128-055 AD5421 Data Sheet To determine the absolute worst-case overall error, the reference Excessive junction temperature can occur if the AD5421 and R errors can be directly summed with the specified AD5421 experiences elevated voltages across its terminals while SET maximum error. For example, when using an external reference regulating the loop current at a high value. The resulting junction temperature depends on the ambient temperature. and external RSET resistor, the maximum AD5421 error is 0.048% of full-scale range. Assuming that the absolute errors for the Table 24 provides the bounds of operation at maximum ambient voltage reference and RSET resistor are, respectively, 0.04% and temperature and maximum supply voltage. This information is 0.05% with temperature coefficients of 3 ppm/°C and 2 ppm/°C, displayed graphically in Figure 50 and Figure 51. These figures respectively, the overall worst-case error is as follows: assume that the exposed paddle is connected to a copper plane 2 Worst-Case Error = of approximately 6 cm . AD5421 Error + V Absolute Error + V TC + 4.5 REF REF Absolute Error + R TC RSET SET 4.0 Worst-Case Error = 3.5 6 TSSOP 0.048% + 0.04% + [(3/10 ) × 100 × 145]% + 3.0 6 0.05% + [(2/10 ) × 100 × 145]% = 0.21% FSR 2.5 This is the absolute worst-case value when the AD5421 operates LFCSP 2.0 over the temperature range of −40°C to +105°C. An error of this value is very unlikely to occur because the temperature coeffi- 1.5 cients of the individual components do not exhibit the same 1.0 drift polarity, and, therefore, an element of cancelation occurs. 0.5 For this reason, the TC values should be added in a root of squares fashion. 0 0 20 40 60 80 100 A further improvement can be gained by performing a two-point AMBIENT TEMPERATURE (°C) calibration at zero scale and full scale, thus reducing the absolute Figure 50. Maximum Power Dissipation vs. Ambient Temperature errors of the voltage reference and R resistor to a combined SET 60 error of 1 LSB or 0.0015% FSR. After performing this calibration, TSSOP the total maximum error becomes 50 Total Error = LFCSP 40 2 2 0.048%+ 0.0015%+ (0.0435%) + (0.029%) = 0.102% FSR 30 To reduce this error value further, a voltage reference and RSET resistor with lower TC specifications must be chosen. 20 THERMAL AND SUPPLY CONSIDERATIONS 10 The AD5421 is designed to operate at a maximum junction temp- erature of 125°C. To ensure reliable and specified operation over 0 the lifetime of the product, it is important that the device not be 40 50 60 70 80 90 100 operated under conditions that cause the junction temperature AMBIENT TEMPERATURE (°C) to exceed this value. Figure 51. Maximum Supply Voltage vs. Ambient Temperature Table 24. Thermal and Supply Considerations (External MOSFET Not Connected) Parameter Description 32-Lead LFCSP 28-Lead TSSOP Maximum Maximum permitted power T − T T − T 125− 105 125−105 J MAX A J MAX A = = 625mW = = 500 mW Power dissipation when operating at an θ 32 θ 40 JA JA Dissipation ambient temperature of 105°C Maximum Maximum permitted ambient T − P ×θ = T − (P ×θ )= J MAX D JA J MAX D JA Ambient temperature when operating from a 125− ((52× 0.0228)× 32)= 87°C 125−((52× 0.0228)× 40)= 77°C Temperature supply of 52 V while regulating a loop current of 22.8 mA Maximum Maximum permitted supply voltage T − T T − T 125− 105 125−105 J MAX A J MAX A = = 27 V = = 21 V Supply when operating at an ambient I ×θ 0.0228× 32 I ×θ 0.0228× 40 LOOP JA LOOP JA Voltage temperature of 105°C while regulating a loop current of 22.8 mA Rev. D | Page 32 of 36 SUPPLY VOLTAGE (V) POWER DISSIPATION (W) 09128-102 09128-103 Data Sheet AD5421 OUTLINE DIMENSIONS 5.10 0.30 5.00 SQ 0.25 4.90 0.18 PIN 1 INDICATOR 25 32 24 1 0.50 BSC EXPOSED 3.65 PAD 3.50 SQ 3.45 8 17 16 9 0.50 0.25 MIN TOP VIEW BOTTOM VIEW 0.40 0.30 3.50 REF 0.80 FOR PROPER CONNECTION OF 0.75 0.05 MAX THE EXPOSED PAD, REFER TO 0.70 THE PIN CONFIGURATION AND 0.02 NOM FUNCTION DESCRIPTIONS COPLANARITY SECTION OF THIS DATA SHEET. 0.08 SEATING 0.20 REF PLANE COMPLIANT TO JEDEC STANDARDS MO-220-WHHD. Figure 52. 32-Lead Lead Frame Chip Scale Package [LFCSP_WQ] 5 mm × 5 mm Body, Very Very Thin Quad (CP-32-11) Dimensions shown in millimeters 9.80 5.55 9.70 5.50 9.60 5.45 28 15 4.50 3.05 EXPOSED 4.40 PAD 3.00 4.30 (Pins Up) 2.95 1 6.40 BSC 14 PIN 1 INDICATOR TOP VIEW BOTTOM VIEW 1.05 0.20 1.00 0.09 1.20 MAX FOR PROPER CONNECTION OF 0.80 0.25 THE EXPOSED PAD, REFER TO THE PIN CONFIGURATION AND FUNCTION DESCRIPTIONS 8° 0.75 SEATING 0.15 MAX SECTION OF THIS DATA SHEET. 0° 0.60 PLANE 0.65 BSC 0.30 0.05 MIN 0.45 COPLANARITY 0.19 0.10 COMPLIANT TO JEDEC STANDARDS MO-153-AET Figure 53. 28-Lead Thin Shrink Small Outline Package, Exposed Pad [TSSOP_EP] (RE-28-2) Dimensions shown in millimeters Rev. D | Page 33 of 36 PIN 1 INDICATOR 04-02-2012-A 05-08-2006-A AD5421 Data Sheet ORDERING GUIDE 1 Model Temperature Range Package Description Package Option AD5421ACPZ-REEL7 −40°C to +105°C 32-Lead LFCSP_WQ CP-32-11 AD5421BCPZ-REEL7 −40°C to +105°C 32-Lead LFCSP_WQ CP-32-11 AD5421BREZ −40°C to +105°C 28-Lead TSSOP_EP RE-28-2 AD5421BREZ-REEL −40°C to +105°C 28-Lead TSSOP_EP RE-28-2 AD5421BREZ-REEL7 −40°C to +105°C 28-Lead TSSOP_EP RE-28-2 AD5421CREZ −40°C to +105°C 28-Lead TSSOP_EP RE-28-2 AD5421CREZ-RL −40°C to +105°C 28-Lead TSSOP_EP RE-28-2 AD5421CREZ-RL7 −40°C to +105°C 28-Lead TSSOP_EP RE-28-2 EVAL-AD5421SDZ Evaluation Board 1 Z = RoHS Compliant Part. Rev. D | Page 34 of 36 Data Sheet AD5421 NOTES Rev. D | Page 35 of 36 AD5421 Data Sheet NOTES ©2011–2012 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D09128-0-5/12(D) Rev. D | Page 36 of 36
Frequently asked questions
What makes Elite.Parts unique?
What kind of warranty will the AD5421 have?
Which carriers does Elite.Parts work with?
Will Elite.Parts sell to me even though I live outside the USA?
I have a preferred payment method. Will Elite.Parts accept it?
Why buy from GID?
Quality
We are industry veterans who take pride in our work
Protection
Avoid the dangers of risky trading in the gray market
Access
Our network of suppliers is ready and at your disposal
Savings
Maintain legacy systems to prevent costly downtime
Speed
Time is of the essence, and we are respectful of yours
Manufacturers


What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods