SQFlash 2.5” SATA-SSD 2.5” SATA-SSD Datasheet Specifications subject to change without notice, contact your sales representatives for the most update information. REV 0.5 Page 1 of 20 Apr. 21, 2010 SQFlash 2.5” SATA-SSD CONTENTS 1. Overview ............................................................................................ 4  2. Features ............................................................................................. 5  3. General Description .......................................................................... 6  4. Pin Assignment and Description ..................................................... 8      4.1 2.5” SATA-SSD Interface Pin Assignments (Signal Segment) ......................................... 8     4.2 2.5” SATA-SSD Interface Pin Assignments (Power Segment) ......................................... 8 5. Identify Device Data .......................................................................... 9  6. ATA Command Set .......................................................................... 11  7. System Power Consumption ......................................................... 18      7.1 Supply Voltage .............................................................................................................. 18     7.2 Power Consumption ...................................................................................................... 18 8. Physical Dimension ........................................................................ 19  Appendix: Part Number Table ........................................................... 20  Specifications subject to change without notice, contact your sales representatives for the most update information. REV 0.5 Page 2 of 20 Apr. 21, 2010 SQFlash 2.5” SATA-SSD Revision History Rev. Date History st 0.1 2009/10/14 1. 1 draft 0.2 2009/10/21 1. Revise specification 0.3 2009/11/19 1. Revise specification 0.4 2009/12/17 1. Create 8GB LBA data 0.5 2010/4/21 1. Add 4GB SLC SSD Advantech reserves the right to make changes without further notice to any products or data herein to improve reliability, function, or design. Information furnished by Advantech is believed to be accurate and reliable. However, Advantech does not assure any liability arising out of the application or use of this information, nor the application or use of any product or circuit described herein, neither does it convey any license under its patent rights nor the rights of others. Copyright © 1983-2010 Advantech Co., Ltd. All rights reserved. Specifications subject to change without notice, contact your sales representatives for the most update information. REV 0.5 Page 3 of 20 Apr. 21, 2010 SQFlash 2.5” SATA-SSD 1. Overview Advantech SQFlash 2.5” SATA-SSD (Solid State Drive) delivers all the advantages of Flash Disk technology with the Serial ATA II interface, fully compliant with standard 2.5-inch form factor. SATA Drives are replacing the older and slower (PATA) interface in embedded environments. The SATA SSD is based on a standard 7-pin interface for data segment and 15-pin for power segment, designed to operate at a maximum operating frequency of 150MHz with 30MHz external crystal. Its capacity could provide a wide range from 8GB to up to 256GB. Also it can reach 220MB/s read as well as 160MB/s write high performance based on MLC flash (with 64MB DDR enabled and measured by CrystalDiskMark v2.1). The power consumption of Flash Disk is much lower than traditional Hard Drive. In addition, Advantech SQFlash 2.5” SATA-SSD provides hot-swapping abilities when removing, replacing or upgrading flash disks. Specifications subject to change without notice, contact your sales representatives for the most update information. REV 0.5 Page 4 of 20 Apr. 21, 2010 SQFlash 2.5” SATA-SSD 2. Features „ Standard SATA interface – Support SATA 1.5 Gbps and 3.0 Gbps interface – SATA Revision 2.6 compliant – Power management supported „ Operating Voltage：5.0V „ Support 48/32/28 bit ECC correct per 2K Byte data „ Capacities – SLC type：4GB，8GB，16GB，32GB，64GB – MLC type：16GB，32GB，64GB，128GB，256GB „ Performance – SLC type ● Sustain Read Speed up to 210 MB/s ● Sustain Write Speed up to 200 MB/s – MLC type ● Sustain Read Speed up to 220 MB/s ● Sustain Write Speed up to 160 MB/s „ Temperature Ranges – Commercial Temperature ● 0℃ to 70℃ for operating ● -40℃ to 85℃ for storage – Industrial Temperature ● -40℃ to 85℃ for operating ● -40℃ to 85℃ for storage „ Mechanical Specification – Shock：1,500G / 0.5ms – Vibration：20G / 80~2,000Hz „ Humidty – Humidity：5% ~ 95% under 55℃ „ Endurance – > 2,000,000 program/erase cycles „ MTBF – 2,000,000 hours „ Data Retention – 10 years „ Acquired RoHS、WHQL、CE、FCC Certificate „ Acoustic：0 dB „ Dimension：100 mm x 69.85 mm x 9.5 mm Specifications subject to change without notice, contact your sales representatives for the most update information. REV 0.5 Page 5 of 20 Apr. 21, 2010 SQFlash 2.5” SATA-SSD 3. General Description „ Advanced NAND Flash Controller Advantech SQFlash 2.5” SATA-SSD includes Bad Block Management Algorithm, Wear Leveling Algorithm and Error Detection / Correction Code (EDC/ECC) Algorithm. „ Bad Block Management Bad blocks are blocks that contain one or more invalid bits of which the reliability is not guaranteed. Bad blocks may be representing when flash is shipped and may developed during life time of the device. Advantech SQFlash 2.5” SATA-SSD implement an efficient bad block management algorithm to detect the factory produced bad blocks and manages any bad blocks that may develop over the life time of the device. This process is completely transparent to the user, user will not aware of the existence of the bad blocks during operation. „ Wear Leveling NAND Type flash have individually erasable blocks, each of which can be put through a finite number of erase cycles before becoming unreliable. It means after certain cycles for any given block, errors can be occurred in a much higher rate compared with typical situation. Unfortunately, in the most of cases, the flash media will not been used evenly. For certain area, like file system, the data gets updated much frequently than other area. Flash media will rapidly wear out in place without any rotation. Wear leveling attempts to work around these limitations by arranging data so that erasures and re-writes are distributed evenly across the full medium. In this way, no single sector prematurely fails due to a high concentration of program/erase cycles. Advantech SQFlash 2.5” SATA-SSD provides advanced wear leveling algorithm, which can efficiently spread out the flash usage through the whole flash media area. By implement both dynamic and static wear leveling algorithms, the life expectancy of the flash media can be improved significantly. „ Error Detection / Correction Advantech SQFlash 2.5” SATA-SSD utilizes BCH ECC Algorithm which offers one of the most powerful ECC algorithms in the industry. This algorithm can support 48/32/28 bit ECC correct per 2K Byte data. „ Sophisticate Product Management Systems Since industrial application require much more reliable devices compare with consumer product, a more sophisticated product management system become necessary for industrial customer requirement. The key to providing reliable devices is product traceability and failure analysis system. By implement such systems end customer can expect much more reliable product. Specifications subject to change without notice, contact your sales representatives for the most update information. REV 0.5 Page 6 of 20 Apr. 21, 2010 SQFlash 2.5” SATA-SSD „ Block Diagram „ LBA、Cylinders、Heads、Sectors value for SLC type Density LBA (K bytes) Cylinders Heads Sectors 4 GB 7,863,912 15,603 16 63 8 GB 15,727,824 15,603 16 63 16 GB 31,587,696 16,383 16 63 32 GB 64,323,504 16,383 16 63 64 GB 129,760,848 16,383 16 63 „ LBA、Cylinders、Heads、Sectors value for MLC type Density LBA (K bytes) Cylinders Heads Sectors 16 GB 30,080,736 16,383 16 63 32 GB 60,292,512 16,383 16 63 64 GB 124,780,320 16,383 16 63 128 GB 253,891,646 16,383 16 63 256 GB 508,952,304 16,383 16 63 Specifications subject to change without notice, contact your sales representatives for the most update information. REV 0.5 Page 7 of 20 Apr. 21, 2010 SQFlash 2.5” SATA-SSD 4. Pin Assignment and Description 4.1 2.5” SATA-SSD Interface Pin Assignments (Signal Segment) Pin # Function Description nd S1 GND 2 mate S2 A+ Differential signal pair A S3 A- nd S4 GND 2 mate S5 B- Differential signal pair B S6 B+ nd S7 GND 2 mate 4.2 2.5” SATA-SSD Interface Pin Assignments (Power Segment) Pin # Function P1 Not Used (3.3V) P2 Not Used (3.3V) P3 Not Used (3.3V Pre-Charge) P4 GND P5 GND P6 GND P7 5V Pre-Charge P8 5V P9 5V P10 GND P11 RESERVED P12 GND P13 Not Used (12V Pre-Charge) P14 Not Used (12V) P15 Not Used (12V) Specifications subject to change without notice, contact your sales representatives for the most update information. REV 0.5 Page 8 of 20 Apr. 21, 2010 SQFlash 2.5” SATA-SSD 5. Identify Device Data The Identity Device Data enables Host to receive parameter information from the device. The parameter words in the buffer have the arrangement and meanings defined in below table. All reserve bits or words are zero F：Fixed Word Default V：Variable Data Field Type Information Address Value X：Both 0 F 045Ah General configuration bit-significant information 1 X 3FFFh Obsolete – Number of logical cylinders (16383) 2 V 0h Specific configuration 3 X 0010h Obsolete – Number of logical heads (16) 4-5 X 02007E00h Retired 6 X 003Fh Obsolete – Number of logical sectors per logical track (63) 7 - 8 V 0h Reserved for assignment by the Compact Flash Association 9 X 0h Retired 10 - 19 F Varies Serial number (20 ASCII characters) 20 - 21 X 0h Retired 22 X 0h Obsolete 23 - 26 F Varies Firmware revision (8 ASCII characters) 27 - 46 F Varies Model number (xxxxxxxx) 7:0- Maximum number of sectors transferred per interrupt on 47 F 8001h MULTIPLE commands 48 F 0h Reserved 49 F 0F00h Capabilities 50 F 4000h Capabilities 51 - 52 X 00000200h Obsoleted 53 F 0007h Words 88 and 70:64 valid 54 X 3FFFh Obsolete – Number of logical cylinders (16383) 55 X 0010h Obsolete – Number of logical heads (16) 56 X 003Fh Obsolete – Number of logical sectors per track (63) 57 - 58 X 00FBFC10h Obsolete 59 F 0100h Number of sectors transferred per interrupt on MULTIPLE commands 037DFF40h (32G) 60 - 61 F Total number of user addressable sectors xxxxxxxxh (64G) 62 X 0h Obsolete 63 F 0007h Multi-word DMA modes supported/selected 64 F 0003h PIO modes supported 65 F 0078h Minimum Multiword DMA transfer cycle time per word 66 F 0078h Manufacturer’s recommended Multiword DMA transfer cycle time 67 F 0078h Minimum PIO transfer cycle time without flow control 68 F 0078h Minimum PIO transfer cycle time with IORDY flow control 69 - 70 F 0h Reserved 71 - 74 F 0h Reserved for the IDENTIFY PACKET DEVICE command 75 F 0h Queue depth 76 F 0002h Serial SATA capabilities 77 F 0h Reserved for future Serial ATA definition 78 F 0h Serial ATA features supported 79 V 0H Serial ATA features enabled 80 F 00F8h Major Version Number 81 F 0021h Minor Version Number 82 F 7429h Command set supported Specifications subject to change without notice, contact your sales representatives for the most update information. REV 0.5 Page 9 of 20 Apr. 21, 2010 SQFlash 2.5” SATA-SSD F：Fixed Word Default V：Variable Data Field Type Information Address Value X：Both 83 F 7008h Command set supported 84 F 4000h Command set/feature supported extension 85 V 7028h Command set/feature enabled 86 V 3000h Command set/feature enabled 87 V 4000h Command set/feature default 88 V 007Fh Ultra DMA Modes 89 F 0h Time required for security erase unit completion 90 F 0h Time required for Enhanced security erase completion 91 V 0h Current advanced power management value 92 V 0h Master Password Revision Code Hardware reset result. The contents of the bits (12:0) of this word shall 93 F 0h change only during the executeion of s hardware reset. 94 V 0h Vebdor’s recommended and actual acoustic management value 95 F 0h Stream Minimum Request Size 96 V 0h Streaming Transfer Time – DMA 97 V 0h Streaming Access Latency – DMA and PIO 98 - 99 F 0h Streaming Performance Granularity xxxxxxxxh (32G) xxxxxxxxh (64G) 100 - 103 V Maximum user LBA for 48 bit Address feature set xxxxxxxxh (128G) xxxxxxxxh (256G) 104 V 0h Streaming Transfer Time – PIO 105 F 0h Reserved 106 F 0h Physical sector size / Logical sector size 107 F 0h Inter-seek delay for ISO-7779 acoustic testing in microseconds 108 - 111 F 0h Unique ID 112 - 115 F 0h Reserved 116 V 0h Reserved 117 - 118 F 0h Words per logical Sector 119 F 0h Supported settings 120 F 0h Command set/Feature Enabled/Supported 121 - 126 F 0h Reserved 127 F 0h Removable Media Status Notification feature set support 128 V 0h Security status 129 - 159 X 0h Vendor specific 160 F 0h Compact Flash Association (CFA) power mode 1 161 - 175 X 0h Reserved for assignment by the CFA 176 - 205 V 0h Current media serial number 206 - 216 F 0h Reserved 217 F 0h Non-rotating media device 218 - 221 F 0h Reserved 222 F 0h Reserved 223 - 233 F 0h Reserved 234 0h Reserved 235 0h Reserved 236 - 254 F 0h Reserved 255 X Varies Integrity word (Checksum and Signature) Specifications subject to change without notice, contact your sales representatives for the most update information. REV 0.5 Page 10 of 20 Apr. 21, 2010 SQFlash 2.5” SATA-SSD 6. ATA Command Set [Command Set List] No. Command set Code Protocol Argument 1 CHECK POWER MODE 98h,E5h ND 28-bit 2 DOWNLOAD MICROCODE 92h PO 28-bit 3 EXECUTE DEVICE DIAGNOSTIC 90h DD 28-bit 4 FLUSH CACHE E7h ND 28-bit 5 FLUSH CACHE EXT EAh ND 28-bit 6 IDENTIFY DEVICE ECh PI 28-bit 7 IDLE 97h,E3h ND 28-bit 8 IDLE IMMEDIATE 95h,E1h ND 28-bit 9 INITIALIZE DEVICE PARAMETERS 91h ND 28-bit 10 NOP 00h ND 28-bit 11 READ BUFFER E4h PI 28-bit 12 READ DMA C8h,C9h DM 28-bit 13 READ DMA EXT 25h DM 48-bit 14 READ MULTIPLE C4h PI 28-bit 15 READ MULTIPLE EXT 29h PI 48-bit 16 READ NATIVE MAX ADDRESS F8h ND 28-bit 17 READ NATIVE MAX ADDRESS EXT 27h ND 48-bit 18 READ SECTOR(S) 20h, PI 28-bit 19 READ SECTOR(S) EXT 24h PI 48-bit 20 READ VERIFY SECTOR(S) 40h,41h ND 28-bit 21 READ VERIFY EXT 42h ND 48-bit 22 RECALIBRATE 1Xh ND 28-bit 23 SECURITY DISABLE PASSWORD F6h PO 28-bit 24 SECURITY ERASE PREPARE F3h ND 28-bit 25 SECURITY ERASE UNIT F4h PO 28-bit 26 SECURITY FREEZE F5h ND 28-bit 27 SECURITY SET PASSWORD F1h PO 28-bit 28 SECURITY UNLOCK F2h PO 28-bit 29 SEEK 7Xh ND 28-bit 30 SET MAX ADDRESS F9h ND 28-bit 31 SET MAX ADDRESS EXT 37h ND 48-bit 32 SET FEATURE EFh ND 28-bit 33 SET MULTIPLE C6h ND 28-bit 34 SLEEP 99h,E6h ND 28-bit 35 SMART READ DATA B0h 36 SMART ENABLE/DISABLE AUTO SAVE B0h 37 SMART EXECUTE OFF-LINE B0h 38 SMART READ LOG B0h 39 SMART ENABLE OPERATION B0h 40 SMART DISABLE OPERATION B0h 41 SMART RETURN STATUS B0h 42 STANDBY 96h,E2h ND 28-bit 43 STANDBY IMMEDIATE 94h,E0h ND 28-bit 44 WRITE BUFFER E8h PO 28-bit 45 WRITE DMA CAh,CBh DM 28-bit 46 WRITE DMA EXT 35h DM 48-bit 47 WRITE MULTIPLE C5h PO 28-bit Specifications subject to change without notice, contact your sales representatives for the most update information. REV 0.5 Page 11 of 20 Apr. 21, 2010 SQFlash 2.5” SATA-SSD No. Command set Code Protocol Argument 48 WRITE MULTIPLE EXT 39h PO 48-bit 49 WRITE SECTOR(S) 30h PO 28-bit 50 WRITE SECTOR(S) EXT 34h PO 48-bit 51 WRITE SECTOR(S) W/O ERASE 38h PO 28-bit 52 WRITE VERIFY 3Ch PO 28-bit Note: ND = Non-Data Command PI = PIO Data-In Command PO = PIO Data-Out Command DM = DMA Command DD = Execute Diagnostic Command Specifications subject to change without notice, contact your sales representatives for the most update information. REV 0.5 Page 12 of 20 Apr. 21, 2010 SQFlash 2.5” SATA-SSD [Command Set Descriptions] 1. CHECK POWER MODE (code: 98h or E5h); This command allow host to determine the current power mode of the device. 2. DOWNLOAD MICROCODE (code: 92h); This command enable the host to alter the device’s microcode. The data transferred using the DOWNLOAD MICROCODE command is vendor specific. All transfers shall be an integer multiple of the sector size. The size of the data transfer is determined by the content of the LBA Low register and the Sector Count register. This allows transfer sizes from 0 bytes to 33,553,920 bytes, in 512bytes increments. 3. EXECUTE DEVICE DIAGNOSTIC (code: 90h); This command performs the internal diagnostic tests implemented by the module. 4. FLUSH CACHE (code: E7h); This command used by the host to request the device to flush the write cache. 5. FLUSH CACHE EXT (code: EAh); This command is used by the host to request the device to flush the write cache. If there is data in the write cache, that data shall be written to the media. 6. IDENTIFY DEVICE (code: ECh); The IDENTIFY DEVICE command enables the host to receive parameter information from the module. 7. IDLE (code: 97h or E3h); This command allows the host to place the module in the IDLE mode and also set the Standby timer. INTRQ may be asserted even through the module may not have fully transitioned to IDLE mode. If the Sector Count register is non-”0”, then the Standby timer shall be enabled. The value in the Sector Count register shall be used to determine the time programmed into the Standby timer. If the Sector Count register is “0” then the Standby timer is disabled. 8. IDLE IMMEDIATE (code: 95h or E1h); This command causes the module to set BSY, enter the Idle (Read) mode, clear BSY and generate an interrupt. 9. INITIALIZE DEVICE PARAMETERS (code: 91h); This command enables the host to set the number of sectors per track and the number of heads per cylinder. 10. NOP (code: 00h); If this command is issued, the module respond with command aborted. 11. READ BUFFER (code: E4h); This command enables the host to read the current contents of the module's sector buffer. 12. READ DMA (code: C8h or C9h); This command reads from “1” to “256” sectors as specified in the Sector Count register using the DMA data transfer protocol. A sector count of “0” requests “256” sectors transfer. The transfer begins at the sector specified in the Sector Number register. 13. READ DMA Ext (code: 25h); This command allows the host to read data using the DMA data transfer protocol. Specifications subject to change without notice, contact your sales representatives for the most update information. REV 0.5 Page 13 of 20 Apr. 21, 2010 SQFlash 2.5” SATA-SSD 14. READ MULTIPLE (code: C4h); This command performs similarly to the READ SECTORS command. Interrupts are not generated on each sector, but on the transfer of a block which contains the number of sector per block is defined by the content of word 59 in the IDENTIFY DEVICE response. 15. READ MULTIPLE EXT (code: 29h); This command performs similarly to the READ SECTORS command. The number of sectors per block is defined by a successful SET MULTIPLE command. If no successful SET MULTIPLE command has been issued, the block is defined by the device’s default value for number of sectors per block as defined in bits (7:0) in word 47 in the IDENTIFY DEVICE information. 16. READ NATIVE MAX ADDRESS (code: F8h); This command returns the native maximum address. The native maximum address is the highest address accepted by the device in the factory default condition. 17. READ NATIVE MAX ADDRESS EXT (code: 27h); This command returns the native maximum address. 18. READ SECTOR(S) (code: 20h or 21h); This command reads from “1” to “256” sectors as specified in the Sector Count register. A sector count of “0” requests “256” sectors transfer. The transfer begins at the sector specified in the Sector Number register. 19. READ SECTOR(S) EXT (code: 24h); This command reads from “1” to “65536” sectors as specified in the Sector Count register. A sector count of “0” requests “65536” sectors transfer. The transfer begins at the sector specified in the Sector Number register. 20. READ VERIFY SECTOR(S) (code: 40h or 41h); This command is identical to the READ SECTORS command, except that DRQ is never set and no data is transferred to the host. 21. READ VERIFY SECTOR(S) EXT (code: 42h); This command is identical to the READ SECTORS command, except that DRQ is never set and no data is transferred to the host. 22. RECALIBRATE (code: 1xh); This command return value is select address mode by the host request. 23. SECURITY DISABLE PASSWORD (code: F6h); This command transfers 512 bytes of data from the host. Table defines the content of this information. If the password selected by word 0 match the password previously saved by the device, the device shall disable the Lock mode. This command shall not change the Master password. The Master password shall be reactivated when a User password is set. 24. SECURITY ERASE PREPARE (code: F3h); This command shall be issued immediately before the SECURITY ERASE UNIT command to enable device eraseing and unlocking. 25. SECURITY ERASE UNIT (code: F4h); This command transfer 512 bytes of data from the host. Table## defines the content of this information. If the password does not match the password previously saved by the device, the device shall reject the command with command aborted. Specifications subject to change without notice, contact your sales representatives for the most update information. REV 0.5 Page 14 of 20 Apr. 21, 2010 SQFlash 2.5” SATA-SSD The SECURITY ERASE PREPARE command shall be completed immediately prior to the SECURITY ERASE UNIT command. 26. SECURITY FREEZE LOCK (code: F5h); This command shall set the device to frozen mode. After command completion any other commands that update the device Lock mode shall be command aborted. Frozen shall be disabled by power-off or hardware reset. If SECURITY FREEZE LOCK is issued when the drive is in frozen mode, the drive executes the command and remains in frozen mode. 27. SECURITY SET PASSWORD (code: F1h); This command transfer 512 bytes of data from the host. Table defines the content of this information. The data transferred controls the function of this command. Table defines the interaction of the identifier and security level bits. 28. SECURITY UNLOCK (code: F2h); This command transfer 512 bytes of data from the host. Table (as Disable Password) defines the content of this information. If the Identifier bit is set to Master and the device is in high security level, then the password supplied shall be compared with the stored Master password. If the device is in maximum security level then the unlock shall be rejected. If the identifier bit is set to user then the device shall compare the supplied password with the stored User password. If the password compare fails then the device shall return command aborted to the host and decrements the unlock counter. This counter shall be initially set to five and shall be decremented for each password mismatch when SECURITY UNLOCK is issued and the device is locked. When this counter reachs zero then SECURITY UNLOCK and SECURITY ERASE UNIT command shall be aborted unitl a power-on or a hardware reset. 29. SEEK (code: 7Xh); This command performs address range check. 30. SET FEATURE (code: EFh); This command is used by the host to establish parameters that affect the execution of certain device features. 31. SET MAX ADDRESS (code: F9h); After successful command completion, all read and write access attempts to address greater than specified by the successful SET MAX ADDRESS command shall be rejected with an IDNF error. IDENTIFY DEVICE response words (61:60) shall reflect the maximum address set with this command. 32. SET MAX ADDRESS EXT (code: 37h); After successful command completion, all read and write access attempts to address greater than specified by the successful SET MAX ADDRESS command shall be rejected with an IDNF error. IDENTIFY DEVICE response words (61:60) shall reflect the maximum address set with this command. 33. SET MULTIPLE MODE (code: C6h); This command enables the device to perform READ and Write Multiple operations and establishes the block count for these commands. 34. SLEEP (code: 99h or E6h); This command causes the module to set BSY, enter the Sleep mode, clear BSY and generate an interrupt. Specifications subject to change without notice, contact your sales representatives for the most update information. REV 0.5 Page 15 of 20 Apr. 21, 2010 SQFlash 2.5” SATA-SSD 35. SMART READ DATA (code: B0h with Feature register value of D0h); This command returns the Device SMART data structure to the host. 36. SMART ENABLE/DISABLE AUTO SAVE (code: B0h with Feature register value of D2h); This command enables and disables the optional attribute autosave feature of the device. 37. SMART EXECUTE OFF_LINE (code: B0h with Feature register value of D4h); This command cause the device to immediately initiate the optional set of activities that collect SMART data in an off-line mode and then save this data to the device’s non-volatile memory, or execute a self-diagnostic test routine in either captive or off-line mode. 38. SMART READ LOG (code: B0h with Feature register value of D5h); This command returns the specified log data to the host. 39. SMART ENABLE OPERATION (code: B0h with Feature register value of D8h); This command enables access to all SMART capabilities within the device. Prior to receipt of this command SMART data are neither monitored nor saved by the device. 40. SMART DISABLE OPERATION (code: B0h with Feature register value of D9h); This command disables all SMART capabilities within the device including any and all timer and event count functions related exclusively to this feature. After command acceptance the device shall disable all SMART operations. After receipt of this command by the device, all other SMART commands including SMART DISABLE OPERATION commands, with exception of SMART ENABLE OPERATIONS, are disabled and invalid and shall be command aborted by the device. 41. SMART RETURN STATUS (code: B0h with Feature register value of DAh); This command cause the device to communicate the reliability status of the device to the host. 42. STANDBY (code: 96h or E2h); This command causes the module to set BSY, enter the Standby mode, clear BSY and return the interrupt immediately. 43. STANDBY IMMEDIATE (code: 94h or E0h); This command causes the module to set BSY, enter the Standby mode, clear BSY and return the interrupt immediately. 44. WRITE BUFFER (code: E8h); This command enables the host to overwrite contents of the module’s sector buffer with any data pattern desired. 45. WRITR DMA (code: CAh or CBh); This command writes from “1” to “256” sectors as specified in the Sector Count register using the DMA data transfer protocol. A sector count of “0” requests “256” sectors transfer. The transfer begins at the sector specified in the Sector Number register. 46. WRITR DMA EXT (code: 35h); This command writes from “1” to “65536” sectors as specified in the Sector Count register using the DMA data transfer protocol. A sector count of “0” requests “65536” sectors transfer. The transfer begins at the sector specified in the Sector Number register. 47. WRITE MULTIPLE (code: C5h); This command is similar to the WRITE SECTORS command. Interrupts are not presented on each sector, but on the transfer of a block which contains the number of sectors defined by Set Multiple command. Specifications subject to change without notice, contact your sales representatives for the most update information. REV 0.5 Page 16 of 20 Apr. 21, 2010 SQFlash 2.5” SATA-SSD 48. WRITE MULTIPLE EXT (code: 39h); This command is similar to the WRITE SECTORS command. Interrupts are not presented on each sector, but on the transfer of a block which contains the number of sectors defined by Set Multiple command. 49. WRITE SECTOR(S) (code: 30h or 31h); This command writes from “1” to “256” sectors as specified in the Sector Count register. A sector count of “0” requests “256” sectors transfer. The transfer begins at the sector specified in the Sector Number register. 50. WRITE SECTOR(S) EXT (code: 34h); This command writes from “1” to “65536” sectors as specified in the Sector Count register. A sector count of “0” requests “65536” sectors transfer. The transfer begins at the sector specified in the Sector Number register. 51. WRITE SECTOR(S) W/O ERASE (code: 38h); This command writes from “1” to “256” sectors as specified in the Sector Count register. A sector count of “0” requests “256” sectors transfer. The transfer begins at the sector specified in the Sector Number register. 52. WRITE VERIFY (code: 3Ch); This command is similar to the WRITE SECTOR(S) command, except that each sector is verified before the command is completed. Specifications subject to change without notice, contact your sales representatives for the most update information. REV 0.5 Page 17 of 20 Apr. 21, 2010 SQFlash 2.5” SATA-SSD 7. System Power Consumption 7.1 Supply Voltage Parameter Rating Operating Voltage 5V +/- 5% Max. Ripple 100mV, 0~30MHz 7.2 Power Consumption Parameter Value Standby 0.5W Operating 5.3W Specifications subject to change without notice, contact your sales representatives for the most update information. REV 0.5 Page 18 of 20 Apr. 21, 2010 SQFlash 2.5” SATA-SSD 8. Physical Dimension 2.5” SATA SSD (Unit: mm) (Top View) (Side View) (Bottom View) Specifications subject to change without notice, contact your sales representatives for the most update information. REV 0.5 Page 19 of 20 Apr. 21, 2010 SQFlash 2.5” SATA-SSD Appendix: Part Number Table Product Advantech PN Manufacture PN Advantech SQFlash 2.5” SATA SSD 4G SLC, DMA (0~70°C) SQF-S25S4-4G-CTE SSB004GTSC0-S30 Advantech SQFlash 2.5” SATA SSD 8G SLC, DMA (0~70°C) SQF-S25S4-8G-CTE SSB008GTSC0-S30 Advantech SQFlash 2.5” SATA SSD 16G SLC, DMA (0~70°C) SQF-S25S8-16G-CTE SSB016GTSC0-S30 Advantech SQFlash 2.5” SATA SSD 32G SLC, DMA (0~70°C) SQF-S25S8-32G-CTE SSB032GTSC0-S30 Advantech SQFlash 2.5” SATA SSD 64G SLC, DMA (0~70°C) SQF-S25S8-64G-CTE SSB064GTSC0-S30 Advantech SQFlash 2.5” SATA SSD 4G SLC, DMA (-40~85°C) SQF-S25S4-4G-ETE SSB004GTSE0-S30 Advantech SQFlash 2.5” SATA SSD 8G SLC, DMA (-40~85°C) SQF-S25S4-8G-ETE SSB008GTSE0-S30 Advantech SQFlash 2.5” SATA SSD 16G SLC, DMA (-40~85°C) SQF-S25S8-16G-ETE SSB016GTSE0-S30 Advantech SQFlash 2.5” SATA SSD 32G SLC, DMA (-40~85°C) SQF-S25S8-32G-ETE SSB032GTSE0-S30 Advantech SQFlash 2.5” SATA SSD 64G SLC, DMA (-40~85°C) SQF-S25S8-64G-ETE SSB064GTSE0-S30 Advantech SQFlash 2.5” SATA SSD 16G MLC, DMA (0~70°C) SQF-S25M4-16G-CTE SSB016GTMC0-S30 Advantech SQFlash 2.5” SATA SSD 32G MLC, DMA (0~70°C) SQF-S25M8-32G-CTE SSB032GTMC0-S30 Advantech SQFlash 2.5” SATA SSD 64G MLC, DMA (0~70°C) SQF-S25M8-64G-CTE SSB064GTMC0-S30 Advantech SQFlash 2.5” SATA SSD 128G MLC, DMA (0~70°C) SQF-S25M8-128G-CTE SSB128GTMC0-S30 Advantech SQFlash 2.5” SATA SSD 256G MLC, DMA (0~70°C) SQF-S25M8-256G-CTE SSB256GTMC0-S30 Advantech SQFlash 2.5” SATA SSD 16G MLC, DMA (-40~85°C) SQF-S25M4-16G-ETE SSB016GTME0-S30 Advantech SQFlash 2.5” SATA SSD 32G MLC, DMA (-40~85°C) SQF-S25M8-32G-ETE SSB032GTME0-S30 Advantech SQFlash 2.5” SATA SSD 64G MLC, DMA (-40~85°C) SQF-S25M8-64G-ETE SSB064GTME0-S30 Advantech SQFlash 2.5” SATA SSD 128G MLC, DMA (-40~85°C) SQF-S25M8-128G-ETE SSB128GTME0-S30 Advantech SQFlash 2.5” SATA SSD 256G MLC, DMA (-40~85°C) SQF-S25M8-256G-ETE SSB256GTME0-S30 Specifications subject to change without notice, contact your sales representatives for the most update information. REV 0.5 Page 20 of 20 Apr. 21, 2010