ACT/TECHNICO VP417
Specifications
CPU
2.16 GHz Intel Core 2 Duo processor T7400: uses uFC-PGA 478 (micro Flip-Chip Pin Grid Array) package 1.5 GHz Intel Core 2 Duo processor L7400: uses uFC-BGA 478 (micro Flip-Chip Ball Grid Array) package common processor features are: dual-core CPU 667 MHz Front Side Bus 4 Mbytes of secondary (L2) on-die cache 64 Kbytes primary (L1) on-die cache Intel 64 Technology (64-bit computing support) no CPU fan utilizes Intel E7520 server class chipset: uses Intel 6300ESB I/O controller hub provision for XDP debug port
Dimensions
supports up to 4 Gbytes DDR2-400 ECC SDRAM: up to 4 Gbytes soldered on board up to four bit error protection peak bandwidth of 6.4 Gbytes/s dual channel architecture accessible from processor or VME bus
Environment
operating temperatures: 0C to +55C (N-series: up to 2.16 GHz) -25C to +70C (E-series: 1.5GHz) -40C to +85C (K-series: 1.5GHz) storage temperature: -40C to +85C 10% to 90% Relative Humidity non-condensing (operating or storage) K-series includes humidity sealant ruggedized versions available conduction cooled (RC-series: 1.5 GHz) air coooled (RA-series: 1.5 GHz)
Ethernet
two interfaces supporting 10 Base-T, 100 Base-TX, 1000 Base-T: implemented by Intel 82571EB LAN controller via x4 PCI Express link both interfaces accessed via optional P0 1 channel switchable to front panel RJ45 support for VITA 31.1 Gigabit Ethernet for VME64x backplanes
Expansion Interface
+5V@9.8A (typical at 2.16 GHz with 4 Gbytes SDRAM) +12V@0.0A; -12V@0.0A; 3.3V not required +12V and -12V routed to both PMC sites and PMC expansion connector
FDD
Phoenix TrustedCore Server BIOS comprehensive Power-On Self-Test (POST) LAN boot firmware included
Form Factor
1 Mbyte of BIOS flash EPROM 64 Mbytes of Application flash EPROM
Gross Weight
implemented by a Silicon Motion SM722: 8 Mbytes video memory resolutions up to 1280x1024@16M colors analog graphics accessed via a 26-way high-density connector on front panel and via optional P0
IDE Interface
2x EIDE interfaces: supports up to Ultra-DMA 100 for high performance drives second EIDE interface supports CompactFlash carrier with 2 sites (within a single slot) primary channel supports off-board EIDE drives via P2 connector 2x serial ATA150 interfaces: transfer rate up to 150 Mbytes/s 1 channel can be used for on-board 2.5 inch SATA disk drive option for 1 channel via PO
Memory
6U form factor single VME64x slot- front panel width 0.8inch (20.3mm) utilizes 160-way connectors for P1 and P2 optional P0 IEEE 1101.10 handles shock: 20g, 11ms, 1/2 sine (operating) 30g, 11ms, 1/2 sine (non-operating) vibration: 5Hz-2000Hz at 2g, 0.38mm peak displacement (operating) 5Hz-2000Hz at 2g, 0.76mm peak displacement (non-operating)
OS
PC-compatible Real Time Clock (Year 2000 compliant) 3x USB 2.0 interfaces: 1 via a 26-way high-density connector on front panel 1 via P2 connector option for 1 via P0 connector (see Note 1) keyboard and mouse interfaces accessed via a 26-way high-density connector on front panel and optionally via P0 connector watchdog timer 1x32-bit Long Duration Timer with processor interrupt capability
Power Connector
2x PMC sites; for both sites: 32/64-bit, 33/66MHz PCI/PCI-X XMC (PCI Express Mezzanine Card) interface supported via x8 PCI Express link 3.3V or 5V PCI signaling levels PMC site 1 I/O via front panel and P2 PMC site 2 I/O via front panel and optional PO (see note 1) expansion to an optional dual PMC carrier board: via expansion connector (32/bit, 33 MHz) or via baseboard PMC site (64/bit, 66 MHz)
SATA
PCB (PWB) manufactured with flammability rating of 94V-0
Serial
3x serial channel interfaces: 1x RS232 accessed via a 26-way high-density connector on front panel 2x RS232/422/485 accessed via P2 16550 compatible UART
Socket
support for Linux, Windows XP, Windows XP Embedded, Windows 2000, RTX, VxWorks, QNX, Solaris and LynxOS
Video Interface
P1 and P2 connectors compatible with VME64x implemented using Tundra Universe II device VME Master/Slave A32/A24/A16/D64/D62/D32/D16/D8 (E0)/MBLT64 fast hardware byte mapping auto system controller detect full interrupter/interrupt handler support bus error interrupt hardware
Features
- 2 Gigabit Ethernet ports
- 2 x EIDE interfaces
- 2 x SATA interfaces
- 2.16 GHz Intel® Core™ 2 Duo processor T7400 or 1.5 GHz Intel® Core™ 2 Duo processor L7400 Dual-core CPU
- 4 Mbytes of shared secondary (L2) on-die cache
- 64 Kbytes of primary (L1) on-die cache
- 667 MHz Front Side Bus
- Available in extended temperature and conduction cooled versions
- Intel® 64 (or Intel® EM64T) 64-bit computing support
- No CPU fan required
- Operating temperatures: 0°C to +55°C (N-Series: up to 2.16 GHz); -25°C to +70°C (E-Series: 1.5 GHz); -40°C to +85°C (K-Series: 1.5 GHz)
- Supports up to 4 Gbytes DDR2-400 ECC SDRAM
- Up to 3 x RS232 serial channels
- USB and Flash interfaces
Datasheet
Extracted Text
Intel® Core™ 2 Duo Processor Dual PMC Embedded Controller RoHS 2002/95/EC APPLICATIONS The VP 417/03x is a PC-compatible high performance, VP 417/03x is suitable for a range of demanding high functionality VME processor board supporting the applications within the defense, industrial control, 2.16 GHz Intel® Core™ 2 Duo processor T7400 and the telecomms, telemetry, scientific and aerospace 1.5 GHz Intel® Core™ 2 Duo processor L7400. This markets. To simplify the board’s integration many single slot board features 2 PMC sites, up to 4 Gbytes of popular industry standard operating systems are soldered DDR2 SDRAM and a variety of interfaces supported. The board is plug compatible with the including an option for an on-board Hard Disk Drive, popular VP 315/02x and VP 317/02x families (5-row CompactFlash™ or Hitachi GST MicroDrive™. The backplane variants). HIGHLIGHTS � 2.16 GHz or 1.5 GHz Intel® Core™ 2 Duo processor: � Keyboard and mouse interfaces - 667 MHz Front Side Bus � 3 x serial channel interfaces - 64 Kbytes L1 cache � 3 x Universal Serial Bus (USB 2.0) interfaces - 4 Mbytes L2 cache � Watchdog timer; Long Duration Timer - Intel® 64 Technology (64-bit computing support) - no CPU fan needed � VME-64 Interface supporting � Up to 4 Gbytes of dual channel DDR2-400 ECC SDRAM A32/A24/A16/D64/D32/D16/D8(EO), MBLT64 and with support for fast hardware byte-swapping � High performance SATA and EIDE disk interfaces with optional on-board disk drive � Single slot � CompactFlash™ or Hitachi GST MicroDrive™ on a carrier � Extended temperature versions planned: - -25°C to +70°C (E-Series) � 2 x PMC/XMC module interfaces: - -40°C to +85°C (K-Series, includes humidity sealant) - 32/64-bit, 33/66 MHz PCI/PCI-X™ - supporting 1.5 GHz processor - 2 x XMC module interfaces (x8 PCI Express®) � Ruggedized versions planned: - Expansion carrier for 2 more PMC sites - conduction cooled and air cooled � 2 x 10/100/1000 Mbps Ethernet interfaces: � Support for Linux®, Windows® 2000, Windows® XP, - Gigabit Ethernet for VME64x backplane (VITA 31.1) Windows® XP Embedded, RTX®, VxWorks®, QNX®, � 1 Mbyte of BIOS Flash EPROM Solaris™ and LynxOS® � 64 Mbytes of Application Flash EPROM � Graphics interface 4 Gilberd Court, Colchester, Essex, CO4 9WN, UK CONCURRENT Tel: +44 (0)1206 752626 Fax: +44 (0)1206 751116 6 Tower Office Park, Woburn, MA 01801, USA TECHNOLOGIES Tel: (781) 933 5900 Fax: (781) 933 5911 Central Processor Ethernet Analog 10/100/ 32-bit PMC � 2.16 GHz Intel® Core™ 2 Duo processor USB 1 x RS232 Graphics 1000Mbps PMC 1 PMC 2 Expansion T7400:- Soldered Keyboard DDR2 ECC � uses �FC-PGA 478 (micro Flip-Chip Pin Grid 1x 1 x Serial Mouse USB 2.0 DRAM I/O P0 Array) package Core 2 Duo � 1.5 GHz Intel® Core™ 2 Duo processor SATA Processor BIOS Real-Time L7400:- Flash Clock EPROM x8 � uses �FC-BGA 478 (micro Flip-Chip Ball 3V Intel x8 Grid Array) package Application E7520 Flash Dual CompactFlash � common processor features are:- Carrier CF 2 x Serial x4 TM PCI-X 66 � dual-core CPU ATA Intel 6300ESB � 667 MHz Front Side Bus Universe II � 4 Mbytes of secondary (L2) on-die cache Keyboard SM722 EIDE 2 x Serial 2x Intel Mouse � 64 Kbytes of primary (L1) on-die cache Interface I/O USB 2.0 Graphics 82571EB P0 Byte � Intel® 64 Technology (64-bit computing Swap support) � no CPU fan � utilizes Intel® E7520 server class chipset:- Analog VME 2xRS232/ USB USB 2 x Ethernet KBD P2 P0 Graphics 10/100/1000 PMC 422/485 PMC (VITA 31.1) I/O I/O � uses Intel® 6300ESB I/O Controller Hub SATA EIDE � provision for XDP debug port P2 = PCI-Express Optional P0 DRAM � supports up to 4 Gbytes DDR2-400 ECC Graphics Interface VME Interface SDRAM:- � implemented by a Silicon Motion SM722:- � P1 and P2 connectors compatible with VME64x � up to 4 Gbytes soldered on-board � 8 Mbytes video memory � implemented using Tundra® Universe II™ device � up to four bit error correction � resolutions up to 1280 x 1024 @ 16M � VME Master/Slave � peak bandwidth of 6.4 Gbytes/s colors � A32/A24/A16/D64/D32/D16/D8(EO)/MBLT64 � dual channel architecture � analog graphics accessed via a 26-way � fast hardware byte swapping � accessible from processor or VME bus high-density connector on front panel and � auto system controller detect via optional P0 Hard Disk Interfaces � full interrupter / interrupt handler support � 2 x EIDE interfaces:- Serial Interfaces � bus error interrupt hardware � supports up to Ultra-DMA 100 � 3 x serial channel interfaces:- Electrical Specification � second EIDE interface supports � 1 x RS232 accessed via 26-way high � +5V@9.8A (typical at 2.16 GHz with 4 Gbytes CompactFlash™ carrier with 2 sites (within density connector on front panel SDRAM) a single slot) � 2 x RS232/422/485 accessed via P2 � +12V@0.0A; -12V@0.0A; 3.3V not required � primary channel supports off-board EIDE � 16550 compatible UART � +12V and -12V routed to both PMC sites and drives via P2 connector PMC expansion connector Other Peripheral Interfaces � 2 x Serial ATA150 interfaces:- � PC-compatible Real Time Clock (Year 2000 � transfer rate up to 150 Mbytes/s Environmental Specification compliant) � 1 channel can be used for on-board � operating temperatures:- � 3 x USB 2.0 interfaces:- 2.5 inch SATA disk drive � 0°C to +55°C (N-Series: up to 2.16 GHz) � 1 via a 26-way high-density connector on � option for 1 channel via P0 (see Note 1) � -25°C to +70°C (E-Series: 1.5 GHz) front panel � -40°C to +85°C (K-Series: 1.5 GHz) PMC Interfaces � 1 via P2 connector � storage temperature: -40°C to +85°C � 2 x PMC sites; for both sites:- � option for 1 via P0 connector (see Note 1) � 10% to 90% Relative Humidity, non condensing � 32/64-bit, 33/66 MHz PCI/PCI-X � keyboard and mouse interfaces accessed via a (operating or storage):- � XMC (PCI Express® Mezzanine Card) 26-way high-density connector on front � K-Series includes humidity sealant interface supported via x8 PCI Express Link panel and optionally via P0 connector � ruggedized versions planned:- � 3.3V or 5V PCI signaling levels � watchdog timer � conduction cooled (RC-Series: 1.5 GHz) � PMC Site 1 I/O via front panel and P2 � 1 x 32-bit Long Duration Timer with � air cooled (RA-Series: 1.5 GHz) � PMC Site 2 I/O via front panel and optional processor interrupt capability P0 (see Note 1) Mechanical Specification Flash EPROM � expansion to an optional dual PMC carrier � 6U form-factor � 1 Mbyte of BIOS Flash EPROM board:- � single VME64x slot - front panel width 0.8 inch � 64 Mbytes of Application Flash EPROM � via expansion connector (32-bit/33 MHz) (20.3mm) � or via baseboard PMC site (64-bit/66 MHz) Software Support � utilizes 160-way connectors for P1 and P2 � support for Linux®, Windows® XP, Ethernet Interfaces � optional P0 Windows® XP Embedded, Windows® 2000, � two interfaces supporting 10 Base-T, � IEEE 1101.10 handles RTX®, VxWorks®, QNX®, Solaris™ and LynxOS® 100 Base-TX, 1000Base-T:- � shock: 20g, 11ms, ½ sine (operating); � implemented by Intel® 82571EB LAN 30g, 11ms, ½ sine (non-operating) Firmware Support Controller via x4 PCI Express® link � vibration: 5Hz-2000Hz at 2g, 0.38mm peak � Phoenix® TrustedCore® Server BIOS � both interfaces accessed via optional P0 displacement (operating); � comprehensive Power-On Self-Test (POST) (see Note 1) 5Hz-2000Hz at 5g, 0.76mm peak displacement � LAN boot firmware included � 1 channel switchable to front panel RJ45 (non-operating) Safety � support for VITA 31.1:- The optional P0 connector supports � Gigabit Ethernet for VME64x backplanes � PCB (PWB) manufactured with flammability either PMC Site 2 I/O x64 and 1 x Ethernet or rating of 94V-0 PMC Site 2 I/O x32, SATA, USB and 2 x Ethernet ORDERING INFORMATION Order Number Product Description (Hardware) Replace the order number suffix (-xy) with selections from the following: VP 417/031-xy 1.5 GHz Core 2 Duo Processor L7400 1- 3-row I/O, P2= PMC1 I/O x32, EIDE, USB (1.5 Ghz only) 1 - reserved VP 417/032-xy 2.16 GHz Core 2 Duo Processor T7400 2- 5-row I/O, P2= PMC1 I/O x64, EIDE, USB, 2xRS232/422/485 2 - 2 Gbytes 3- 5-row I/O, P2 as x=2; P0= PMC2 I/O x64, 1xGigE, see ++ 3 - 4 Gbytes AD 110/001-z1 2.5 inch SATA Hard Disk Drive assembly 4- 5-row I/O, P2 as x=2; P0= PMC2 I/O x32, VITA 31.1, USB, 1xSATA see ++ AD 200/001-01 Dual CompactFlash/MicroDrive Carrier AD CRz/PMC-zz PMC Carrier boards for 2 PMC modules ++ when x=3 or 4 then Keyboard, Mouse, VGA available CB 26D/125-00 VGA, Keyboard, Mouse, RS232, USB connector cable DS MSS/001-zzU Board with HDD, CD-RW/DVD, CompactFlash For z options please contact your local sales office For extended temperature, 1.5 GHz E and K-Series, please contact your local sales office All companies and product names are trademarks of their respective organizations. Datasheet Code 1553/0607 Specification subject to change; E and OE. RoHS 2002/95/EC compliant. © Concurrent Technologies 2007 Option Option Option Dual Channel Option Option XMC PMC Module XMC PMC Module 32-bit PCI Bus
Frequently asked questions
What makes Elite.Parts unique?

What kind of warranty will the VP417 have?

Which carriers does Elite.Parts work with?

Will Elite.Parts sell to me even though I live outside the USA?

I have a preferred payment method. Will Elite.Parts accept it?

Why buy from GID?

Quality
We are industry veterans who take pride in our work

Protection
Avoid the dangers of risky trading in the gray market

Access
Our network of suppliers is ready and at your disposal

Savings
Maintain legacy systems to prevent costly downtime

Speed
Time is of the essence, and we are respectful of yours
What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods