CPCI-6065 CompactPCI Peripheral Slot Processor Board Front page ® The Emerson CPCI-6065 series of CompactPCI boards provides competitive The Emerson CPCI-6065 processors, Emerson’s PowerPlus II Architecture, dual 10/100BaseTX Ethernet, two offers maximum perfor- PCI mezzanine card (PMC) slots, and up to 1.5GB of ECC SDRAM. All this is available mance and flexibility. in a single CompactPCI slot. ° MPC7410 or MPC750 class Using the low-power, high-performance MPC7410 or MPC750 class processors, 64-bit Interior page processor local peripheral component interconnect (PCI) bus for the on-board peripherals and processor/memory bus to PCI bus bridge, the CPCI-6065 offers maximum performance ° 1MB or 2MB of L2 cache ® and flexibility. It is also fully compliant to the PICMG 2.1 Hot Swap Specification, ° Up to 1.5GB ECC SDRAM, making it the ideal choice for high availability applications. with optional RAM500 memory expansion modules ° Dual 10/100BaseTX Ethernet interface ° Two 32/64-bit PMC expansion slots with front-panel or backplane I/O ° 16MB on-board flash memory for user-specified requirements ° Two 32-pin PLCC/CLCC sockets for flash memory, up to 1MB capacity for on-board firmware or user specified requirements ° Optional CompactFlash memory card socket on accompanying transition module ° On-board debug monitor with self-test diagnostics ° Two USB ports, four async serial ports ° 32KB NVRAM and time-of-day clock with replaceable battery backup ° Four 32-bit timers, one watchdog timer Front page Interior page CPCI6065 Block Diagram CompactPCI Bus—64-bit EIA-232 3 EIA-232 FP & J3 I/O J3 I/O J1/ J2 MPC7410 64 L2 MPC750 processor Cache Memory 4 Serial Flash 64MB to 1.5GB 1MB Async PowerPC Architecture ECC SDRAM Nontransparent Two PLCCs Bus 32/D64-bit 16MB Flash (Socketed) PCI Bridge NVRAM Hawk 16 RTC PCI Bridge & Memory Bus–144-bit Memory Control PCI Local Bus—A32/D64-bit Two USB PMC PMC J3 I/O Ethernet Ethernet Ethernet Ethernet Slot 1 Slot 2 PCI to ISA/IDE Bridge 10/100BaseTX 10/100BaseTX 64 64 FP I/O or J5 J5 CompactFlash PMC PMC FP I/O FP I/O J5 I/O J3/J5 TranSITIon modulE Hardware Overview The CPCI-6065-TM-PIMC101 transition module IEEE P1386.1 ComPlIanT PmC SloTS provides industry-standard connector access to two The CPCI-6065 features dual PMC ports with support RJ-45 Ethernet connectors, two RJ-45 async serial port for both front-panel and backplane I/O. In addition to connectors (configured as EIA DTE), two headers for providing high-performance expansion I/O, the IEEE async serial ports and two PIM slots for PMC interface P1386.1 compliant PMC ports form a common modules. One socket for optional CompactFlash architecture for future generations of products. memory is also provided. Changing I/O requirements can be satisfied by simply replacing PMCs while reusing the same base platform FIrmwarE monITor and software, reducing the long-term cost of ownership. Firmware must fulfill the traditional functions of test and initialization, in addition to operating system boot PowErPluS II arChITECTurE support. The CPCI-6065 firmware monitor exceeds A second-generation architecture, PowerPlus II these requirements plus expands features like power- Architecture, is a processor and bus architecture fully up tests with extensive diagnostics, as well as a optimized to get the maximum performance from the powerful evaluation and debug tool for simple ® PowerPC architecture-compatible microprocessor checkout or when high-level development debuggers family, the PCI bus and the CompactPCI bus. Features require additional support. All this is included with the added to the original PowerPlus Architecture include CPCI-6065 firmware, plus it supports booting both support for 100 MHz local bus operation and utiliza- operating systems and kernels. tion of synchronous DRAM (SDRAM) technology. The outstanding performance of the PowerPlus II Architecture oPEraTIng SySTEmS and KErnElS is not due to a single factor. A number of elements in CPCI-6065 supports booting VxWorks real-time the design of the PowerPlus II Architecture contribute operating system and kernels, which may be to its outstanding performance including the processor/ purchased from Wind River Systems, Inc. memory subsystem, high-speed local bus, optimally decoupled architecture, decoupling the processor from PCI and the advanced CompactPCI interface that reduces PCI delays. 2 SNAPHAT Battery Front page Interior page Specifications CounTErS/TImErS ° TOD Clock Device: M48T37V; 32KB NVRAM ProCESSor ° Real-Time Timers/Counters: Four 32-bit programmable ° Microprocessor: 450 or 500 MHz MPC750 class or 500 MHz MPC7410 ° Watchdog Timer: Time-out generates reset ° On-chip Cache (I/D): 32K/32K uSB mEmory ° Controller: 82C586 or 82C686 ° ECC Protected Main Memory: PC100 SDRAM with ° Connectors: Routed to J3 for use of two Series A 100 MHz bus receptacles on optional host interface module ° Capacity: 64MB to 1.5GB IEEE P1386.1 PCI mEzzanInE Card SloTS ° Single Cycle Accesses: 10 read/5 write ° Address/Data: A32/D32/D64, PMC JN1, JN2, JN3, ° Read Burst Mode: 7-1-1-1 idle; 2-1-1-1 aligned page hit JN4 connectors ° Write Burst Mode: 4-1-1-1 idle; 2-1-1-1 aligned page hit ° PCI Bus Clock: 33 MHz ° L2 Cache: 1MB (750) or 2MB (7410) ° Signaling: 5V ° EEPROM/Flash: On-board programmable ° Power: +3.3V, +5V, ±12V, 7.5 watts maximum per ° Capacity: 1MB via two 32-pin PLCC/CLCC sockets; PMC slot 16MB surface mount ° Module Types: Two single-wide or one double-wide, ° Read Access (8MB port): 70 clocks (32-byte burst) front panel I/O or J3 and J5 I/O; supports PrPMC module type PMCs (maximum, not including PMC modules) ° Read Access (1MB port): 262 clocks (32-byte burst) ° NVRAM: 32KB; 24KB available for users Note: Due to high component density, uninsulated ° Cell Capacity Life: 5 years at 100% duty cycle, 25° C traces and vias are located in the CPCI-6065 I/O keepout ° Removable Battery: Yes area. If installed, PMC modules having conductive I/O connectors could contact these traces and vias. If full ComPaCTPCI InTErFaCE IEEE 1386-2001 compliance is required, an insulating ® ° Controller: Intel 2155x shield (e.g., Kapton tape) should be installed. ° Address/Data: A32/D32/D64 hoT SwaP ° PCI Bus Clock: 33 MHz Compliant with PICMG Hot Swap Specification, ° Signaling: 3.3V output; input defined by VIO Revision 1.0 dual EThErnET InTErFaCE PowEr rEquIrEmEnTS ® (maximum, not including PMC modules) ° Controller: Two Intel 21143 ° Interface Speed: 10/100Mbps +3.3V ±5% +5V ±5% +12V ±5% –12V ±5% ° PCI Local bus DMA: Yes, with PCI burst CPCI-6065- 2.97 A . 2.65 A 20 mA <10 mA ° Connector: One RJ-45 on front panel or J5/TM, one 3371 additional J5/TM only CPCI-6065- 2.97 A 3.65 A . 20 mA <10 mA aSynChronouS SErIal PorTS 8371 ° Controller: 16C550C UART ° Number of Ports: Four Board SIzE ° Async Baud Rate, bps max.: 38.4K EIA-232 ° Height: 233.4 mm (9.2 in.) ° Connector (COM1): Front panel; also RJ-45 on ° Depth: 160.0 mm (6.3 in.) CPCI-6065-TM-PIMC101 ° Front Panel Height: 261.8 mm (10.3 in.) ° Connector (COM2/3/4): Routed to J3; one RJ-45, ° Width: 19.8 mm (0.8 in.) two headers on CPCI-6065-TM-PIMC101 ° Max. Component Height: 14.8 mm (0.58 in.) 3 Front page Interior page mISCEllanEouS All Modules ° Reset/Abort switch (recessed on the MPC7410) on EnvIronmEnTal front panel Operating Non-operating ° Three LEDs for FAIL, CPU activity and hot swap Temperature: 0° C to +55° C, –40° C to +85° C forced air cooling dEmonSTraTEd mTBF Humidity (NC): 0% to 80% 10% to 90% (based on a sample of eight boards in accelerated stress environment) Vibration: 0.5 G RMS, 6.0 Gs RMS, 20–2000 Hz 20–2000 Hz ° Mean: 214,322 hours random random ° 95% Confidence: 121,141 hours CPCI-6065-TM-PIMC101 Transition Module SaFETy All printed wiring boards (PWBs) are manufactured I/o ConnECTorS with a flammability rating of 94V-0 by UL recognized ° Asynchronous Serial Ports: Two RJ-45 connectors manufacturers. labeled as COM1 and COM2; two 10-pin headers labeled as COM3 and COM4 ElECTromagnETIC ComPaTIBIlITy (EmC) ° Ethernet: Two RJ-45 Intended for use in systems meeting the following regulations: PIm Card SloT Å U.S.: FCC Part 15, Subpart B, Class A ° Power: +3.3V, +5V, +12V, –12V (non-residential) ° Module Types: Two single-wide or one double-wide Å Canada: ICES-003, Class A (non-residential) Note: Jn0 PIM connectors incorporate other This product was tested in a representative system to CPCI-6065 I/O for future host interface modules. the following standards: Å CE Mark per European EMC Directive 89/336/EEC ComPaCTFlaSh mEmory Card InTErFaCE with Amendments; Emissions: EN55022 Class B; ° Controller: 82C586 Immunity: EN55024 ° Interface: ATA, true IDE mode ° CompactFlash Cards (optional): Emerson CFLASH5E-xxx series ° Connector: One standard 50-pin socket Board SIzE ° Height: 233.4 mm (9.2 in.) ° Depth: 80.0 mm (3.1 in.) ° Front Panel Height: 261.8 mm (10.3 in.) ° Width: 19.8 mm (0.8 in.) 4 Front page Interior page Ordering Information Part Number Description CPCI-6065-3371 500 MHZ MPC750 processor, 512MB SDRAM, 5E CPCI-6065-3361 500 MHZ MPC750 processor, 256MB SDRAM, 5E CPCI-6065-8371 500 MHZ MPC7410 processor, 512MB SDRAM, 5E Transition module CPCI-6065-TM-PIMC101 Dual Ethernet transition module for the CPCI-6065 documentation 6806800A67A CPCI-6065 CompactPCI Nonsystem Slot Processor Module Installation and Use MCPN765A/PG MCPN765 CompactPCI Nonsystem Slot Processor Module Programmer's Reference Guide 6806800A84A CPCI-6065-TM-PIMC-0101 Transition Module Installation and Use SoluTIon SErvICES Emerson Network Power provides a portfolio of solution services optimized to meet your needs throughout the product lifecycle. Design services help speed time-to-market. Deployment services include global 24x7 technical support. Renewal services enable product longevity and technology refresh. Plus solution extras include enhanced warranty and repairs. PICMG and CompactPCI are registered trademarks of the PCI Industrial Computer Manufacturers Group. PowerPC is a trademark of IBM Corp. and used under license. Intel is a registered trademark of Intel Corporation or its subsidiaries in the U.S. and other countries. All other product or service names are the property of their respective owners. This document identifies products, their specifications, and their characteristics, which may be suitable for certain applications. It does not constitute an offer to sell or a commitment of present or future availability, and should not be relied upon to state the terms and conditions, including warranties and disclaimers thereof, on which Emerson Network Power may sell products. A prospective buyer should exercise its own independent judgment to confirm the suitability of the products for particular applications. Emerson Network Power reserves the right to make changes, without notice, to any products or information herein which will, in its sole discretion, improve reliability, function, or design. Emerson Network Power does not assume any liability arising out of the application or use of any product or circuit described herein; neither does it convey any license under its patent or other intellectual property rights or under others. This disclaimer extends to any prospective buyer, and it includes Emerson Network Power’s licensee, licensee’s transferees, and licensee’s customers and users. Availability of some of the products and services described herein may be restricted in some locations. AC Power Systems Embedded Power Precision Cooling Emerson Network Power. Connectivity Integrated Cabinet Solutions Services The global leader in enabling DC Power Systems Outside Plant Site Monitoring ™ Business-Critical Continuity . Embedded Computing Power Switching & Control Surge & Signal Protection Business-Critical Continuity, Emerson Network Power and Emerson Network Power the Emerson Network Power logo are trademarks and Offices: Tempe, AZ U.S.A. 1 800 759 1107 or +1 602 438 5720 Madison, WI U.S.A. 1 800 356 9602 or +1 608 831 5500 service marks of Emerson Electric Co. Shanghai, China +86 215292 5693 Paris, France +33 1 69 35 77 00 Tokyo, Japan +81 3 5424 3101 ©2008 Emerson Electric Co. Munich, Germany +49 (0) 89 9 608 2 333 Hong Kong, China +852 2966 3210 Tel Aviv, Israel +972 3 568 4387 www.EmersonNetworkPower.com/EmbeddedComputing CPCI6065-D1 2/08