Industry Pack Modules AcPC8625 ® CompactPCI , Non-intelligent, IP Carrier Card The AcPC8625 is a non-intelligent slave board that interfaces four IP modules to the CompactPCI (cPCI) bus. Mix and match plug-in modules with different I/O functions to quickly create custom I/O boards with hundreds of channels. All 200 I/O points are brought out the rear J4 and J5 connectors. This convenience eliminates messy cables Environmental Operation from hanging out the front of the cage. In addition to a Operating temperature: -25 to 85°C (AcPC8625) Acromag’s carrier boards provide full data access to the more efficient cage wiring design, it is also much easier or -40 to 85°C (AcPC8625E models). IP module’s I/O, ID and interrupt spaces. With full access to insert and replace boards. And with Acromag’s 80mm Storage temperature: -25 to 85°C (AcPC8625) to the programmable registers, you can easily configure transition module (TRANS-C200), all 200 I/O points are or -40 to 85°C (AcPC8625E models). and control the operation of the IP modules from the easily ported out the back of the cage. Relative humidity: 5 to 95% non-condensing. CompactPCI bus. Power: +5V (±5%): 250mA maximum. Features Up to two interrupt requests are supported for each IP ±12V (±5%): 0mA (not used). ■Four industry-standard IP module slots module. All board interrupts are mapped to PCI bus Plus IP module load. INTA# signal. ■Board resides in memory space and MTBF: 409,808 hrs. at 25°C, MIL-HDBK-217F, notice 2. Individual passive filters on each IP power supply line ■Supports IP module I/O, ID and INT spaces provide optimum filtering and noise isolation between Ordering Information ■200 I/O points with rear access the IP modules and the carrier board. Industry Pack Carriers ■High-density rear connectors AcPC8625: CompactPCI carrier. Holds four IP modules. Specifications AcPC8625E: Same as AcPC8625 plus extended temp.range. ■Compatible with all CompactPCI CPUs IP Compliance (ANSI/VITA 4) Software (see Page 81) Meets IP specs per ANSI/VITA 4-1995 (8MHz operation only)■Plug-and-play carrier configuration and ® IPSW-API-VXW: VxWorks software support package and IP I/O mapping to PICMG 2.4 R1.0. interrupt support ® IPSW-API-QNX: QNX software support package Electrical/mechanical interface: ■Two interrupts per IP module ® Supports single or double size IP modules. IPSW-ATX-PCI: ActiveX /OLE Controls 2.0 software package 32-bit IP modules are not supported. ™ IPSW-LINUX: Linux support (website download only)■Front panel LEDs IP Module I/O space, ID space, and INT space supported. Accessories (see Page 87)■Supervisory circuit for reset generation Memory space: Not supported. 5028-438: Cable, SCSI-2 to SCSI-2, shielded. Interrupts: Supports two interrupt requests per IP module and ■Individually filtered and fused power to each IP 5028-378: Termination panel, SCSI-2 connector, interrupt acknowledge cycles via access to IP INT space. 50 screw terminals ■Ruggedized with ESD strip and EMC front panel CompactPCI bus Compliance TRANS-C200: Transition module ■ActiveX/OLE controls available for easy software Meets PCI spec. V2.1 and PICMG 2.0, R2.1. ACPC8625 TRANS-C200 integration (sold separately) Data transfer bus: Slave with 32-bit, 16-bit, and 8-bit data transfer operation 32-bit read/write accesses are imple- mented as two 16-bit transfers to the IPs. Benefits Interrupts: CompactPCI bus INTA# interrupt signal. Up to two ■Clean system cabling. requests sourced from each IP mapped to INTA#. Interrupt vectors come from IP modules via access to IP module INT■Easy board replacement. space. ■Simplified debugging with status LEDs. Plug-and-Play: The system maps the base address into the PCI bus 32-bit memory space. Acromag, Inc.  PO Box 437, Wixom, MI 48393  Phone: 248-624-1541  Fax: 248-624-9234  solutions@acromag.com  www.acromag.com 8 Industry Pack Carriers cPCI Backplane