11/27/12 Gold Box “Infinity” Power Supplies LINEAR REGULATED (to 150 watts) AC-DC single output & wide adjust output • Five Year Warranty STANDARD FEATURES • Highly Configurable, with a seemingly Infinite number of Options • Any slot voltage from 1.5v to 150v is available • Remote Sensing • Open Sense protection • Isolated output • Short circuit and overload protection with enhanced surge capabilities • No minimum load required • Internal EMI Filtering • Pluggable connectors • Can be mounted on two surfaces in any orientation Altitude rating: operation to 10,000 ft and storage to 40,000 ft. Polarity: Output is floating; either positive or negative terminal may be grounded or floated up to 300 volts above ground. Optional controls and monitors are referenced to the SPECIFICATIONS negative terminal. Input Voltage: 105-125 VAC, 50-420 Hz, single phase. (100-132 VAC, 60Hz with 30% derating.) Drift, Warm-up (first 30 minutes after turn-on, @ 25°C): AC Input Current (maximum): 1.3A (LM6A case), 2A (LM8A Voltage mode; ±0.03% or 5 mv, whichever is greater. Current mode (Wide Adjust models); ±0.01% or 10 ma, case), 3A (LM10A case). whichever is greater. Internal Failure Protection: Provided by internal fuse. Drift, Long Term (@ 25°C): Input Undervoltage: An input of less than 105 VAC will not Voltage mode; ±0.01% or 5 mv, whichever is greater, over 8 hours. damage power supply. Voltage mode; ±0.015% or 10 mv, whichever is greater, over Regulation, Ripple (in constant voltage mode): 1000 hours. See tables on pages 6 and 7. Current mode (Wide Adjust models); ±0.01% or 5 ma, whichever is greater, over 8 hours. Regulation, Ripple (in constant current mode): Current mode (Wide Adjust models); ±0.02% or 10 ma, (Wide Adjust Output models) whichever is greater, over 1000 hours. Line Regulation: ±0.01% or 2 mA, whichever is greater. Load Regulation: ±0.01% or 2 mA, whichever is greater. Remote Sensing: Provision for sensing the output voltage Current Ripple: 0.25% rms. across the load, so that drops in the load line are compensated, is a standard feature. Compensates up to 0.5 Start-up Time: 75 to 150 msec. Vdc drop per output line (or within the limits of the output Start-up Surge: 15% overcurrent for 500ms surge voltage adjustment range). (Wide Adjust Output models capability (Single Output models). compensate up to 0.5 Vdc drop per output line.) Turn-off: Exponentially decays to zero. Output Voltage Adjustment: Screwdriver accessible Transient Response: 300 μS to return to ±1% of output through the front panel. setting. Maximum of ±3% output excursion following a load Dielectric Withstand Voltage Isolation step change from 50% to 100%. Input to output: 4242 Vdc 1000 Vdc Short Circuit and Overload Protection: A short or Input to case: 2121 Vdc 500 VAC overload forces the power supply into foldback protection, Output to case: 750 Vdc 300 VAC (Single Output models) or into constant current mode (Wide Cooling: Forced-air cooled; air enters rear of power supply Adjust Output models), with automatic recovery. and exits from front cover. Ambient Operating Temperature: –20 to +71°C. Mounting: Threaded mounting holes permit mounting to a Storage Temperature: –55 to +85°C. chassis, cabinet wall or bracket. To mount from the power Temperature Coefficient (after 30 minute warm-up): supply side of the mounting surface use Mounting Kit GB8 or Voltage mode; ±0.01%/°C (typical). GBR. For DIN rail mounting use Mounting Kit LH35DIN or Current mode (Wide Adjust models); ±0.005%/°C (typical). LR35DIN. Online Ordering and Instant Quotes for ALL Acopian power supplies at www.acopian.com 1 P.O. Box 638, Easton, PA 18044 • Phone: (610) 258-5441 • FAX: (610) 258-2842 NEW!! NEW!! 8/2/11 OPTIONS page (1 of 3) * How to order: See ‘How to Order’, on last Options page. Gold Box “Infinity” Power Supplies Overvoltage Protection Options ........$15 + *$35(one-time only) Choose one: A1 or A2 or A3 or A4 A1; OVP set 15% above rated output. Non-latching. (Available on Single Output models only. Not available with option C9.) A2; OVP set 15% above rated output. Latching. Includes latching overcurrent option “C9”. Reset by momentarily removing AC input power. A3; OVP adjustable from Vout minimum to 15% higher than the maximum rated output voltage. Non-latching. Screwdriver adjustment accessible through the top panel. (Available on Single Output models only.) A4; OVP tracks as Vout is adjusted; OVP triggers between 1v minimum above Vout to 15% above Vout. Latching. (Available on Wide Adjust Output models only.) IEC AC Input Connector Options ........$15 Choose one: B1 or B2 B1; IEC inlet on the rear, with accessible fuse. (Not available with options B4, K5, L2 or on case size LM6A.) B2; IEC inlet on the front, with accessible fuse. (Not available with options B5, C8, L2.) 6' IEC AC input Cord 115 VAC, Option “K3” ........$15 6' IEC AC input Cord 230 VAC, Option “K4” ........$15 AC Input Voltage Options Choose one: B3 or B4 or B5 or B6 or L1 or L2 or L3 B3; 210-250 VAC input. Internally fused for a single phase source. (Not available with option C8.) ........$15 B4; 105-125 VAC or 210-250 VAC input, selectable with switch on rear. Internally fused for a single phase source. ........$25 (Not available with options B1, B9, C8, or on case size LM6A.) B5; 105-125 VAC or 210-250 VAC input, selectable with switch on front. Internally fused for a single phase source. ........$25 (Not available with option B2, B8.) B6; 105-125 VAC or 210-250 VAC strapable input. External fusing required. (Not available with options C8, E6.) ........$20 Input voltage of 115 or 230 VAC can be selected by the use of jumpers on a 4 place pluggable terminal block located on the front panel. L1; 90-110 VAC input. Internally fused for a single phase source ........$40 (Add 5 days to standard shipping time.) (Not available with options C8, E6.) L2; 22-26 VAC input. Internally fused for a single phase source ........$40 (Add 5 days to standard shipping time.) (Not available with options B1, B2, B8, B9, C8, E6.) L3; 195-220 VAC input. Internally fused for a single phase source ........$40 (Add 5 days to standard shipping time.) (Not available with options C8, E6.) Power Switch Options ........$10 Choose one: B8 or B9 B8; AC on/off rocker switch on front panel. (Not available with options C8, L2.) B9; AC on/off rocker switch on rear panel. (Not available with options B4, C8, L2 or on case size LM6A.) Voltage Output Adjust and Current Limit Adjust Options (standard:screwdriver slot accessible through the front panel for Vout adjust.) Choose one: C1 or C2 C1; Front panel knobs; (one for voltage, one for current) used to adjust output voltage and current ........$55 (Current adjustment range is same as for option “C2”) C2; Current Limit adjustment screwdriver slot accessible through the front panel. ........$10 Single Output models; current adjustment range is ±10% of maximum rated output current. Wide Adjust Output models; current adjustment range is from zero to maximum rated output current. Inhibit or Enable Options ........$10 + *$35(one-time only) Choose one: C3 or C4 C3; Inhibit control, TTL compatible. To disable the supply, apply a voltage between the “Rtn” terminal and the “Inh/Ena” terminal. The voltage can be any value from +3 Vdc to +15 Vdc. C4; Enable Control, TTL compatible. To enable the DC output, the “Inh/Ena” terminal must either be shorted to the “Rtn” terminal or pulled to within 0.8 Vdc of the “Rtn” terminal. An open collector or contact closure can be used. *The “$35(one-time only charge)” is only added to the total cost of the power supply one time no matter how many options are ordered. See How To Order. Online Ordering and Instant Quotes for ALL Acopian power supplies at www.acopian.com 2 P.O. Box 638, Easton, PA 18044 • Phone: (610) 258-5441 • FAX: (610) 258-2842 8/2/11 OPTIONS page (2 of 3) * How to order: See ‘How to Order’, on last Options page. Gold Box “Infinity” Power Supplies Output Programming Options (Wide Adjust models only) ........$15 + *$35(one-time only) (voltage and/or current) Choose one: C5 or C6 C5;The output voltage and current may be programmed from 0 to full rating by means of control voltage inputs of 0 to +5 Vdc. C6;The output voltage and current may be programmed from 0 to full rating by means of control voltage inputs of 0 to +10 Vdc. Voltage mode accuracy: 0.5%. Current mode accuracy: 0.5%. Accuracy percentages do not apply below 5% of output rating. C7; Voltage and Current Monitoring, Option “C7” ........$15 + *$35(one-time only) For models with no programming or with 0-10v programming (option “C6”): Voltage Monitor Terminal: Permits remote monitoring of output voltage, stepped down by a ratio of 10:1 (for 3.3v to 90v models) or 100:1 (for 100v to 150v models). Accuracy is 0.5% of maximum rated output voltage. Current Monitor Terminal: For models with greater than 10 amps output current: permits remote monitoring of output current, stepped down by a ratio of 100 mV/Amp (accuracy is 1% of maximum rated output current). For models with less than 10 amps output current: permits remote monitoring of output current, stepped down by a ratio of 1000 mV/Amp (accuracy is 1% of maximum rated output current). For models with 0-5v programming (option “C5”): Voltage Monitor Terminal: Permits remote monitoring of output voltage, stepped down by a ratio of 10:1 (for 3.3v to 45v models) or 100:1 (for 48v to 150v models). Accuracy is 0.5% of maximum rated output voltage. Current Monitor Terminal: For models with greater than 45 amps output current: permits remote monitoring of output current, stepped down by a ratio of 10 mV/Amp. For models with from 5 amps to 45 amps output current: permits remote monitoring of output current, stepped down by a ratio of 100 mV/Amp. For models with less than 4.5 amps output current: permits remote monitoring of output current, stepped down by a ratio of 1000 mV/Amp. (Accuracy is 1% of maximum rated output current.) (When monitoring the output voltage and/or current by means of the monitor terminals, the use of an instrument having an input impedance of at least 10 megohms is recommended.) C8; AC on/off control, Option “C8” ........$35 Apply control voltage between terminals 21 and 22 to turn power supply on. Control voltage range is 11 to 28 Vdc (@ 65ma maximum). (Not available with options B2, B3, B4, B6, B8, B9, E6, L1, L2, L3.) C9; Latching Overcurrent control, Option “C9” ........$5 If current is greater than 15% of the maximum rated output current, the power supply latches off. Reset by momentarily removing AC input power. This option is included with Option A2. (Available on Single Output models only. Not available with options A1, C5, C6.) D1; Over Temperature protection, Option “D1” ........$15 An internal thermostat will automatically shut down the power supply in the event of an over temperature condition. Power supply resets automatically. D2; Thermostatically controlled fan, Option “D2” ........$25 Fan runs at reduced speed until maximum speed is required. E1; Output blocking protection diode, Option “E1” ........$25 Used for battery charging or redundant applications. Derate output by 10%. E2; Transient protection for electrically noisy environments, Option “E2” ........$35 Transient protection for AC input and DC output. E3; High Frequency pulsed load filtering, Option “E3” ........$30 Recommended for applications such as "switched loads" and "stepper motors". E4; Series Operation Diode, Option “E4” ........$15 Allows power supplies to operate in series, for applications requiring higher output voltage. E5; High Isolation Output, Option “E5” ........$25 May be floated at 1000 Vdc above case. (Available only on Single Output models with no options or with options B1-B9, D1, D2, F1, K6.) E6; AC Inrush Current Limiting, Option “E6” ........$35 AC inrush is limited by a 10 ohm impedance. (Not available with options B6, C8, L1, L2, L3.) *The “$35(one-time only charge)” is only added to the total cost of the power supply one time no matter how many options are ordered. See How To Order. Online Ordering and Instant Quotes for ALL Acopian power supplies at www.acopian.com 3 P.O. Box 638, Easton, PA 18044 • Phone: (610) 258-5441 • FAX: (610) 258-2842 11/29/10 OPTIONS page (3 of 3) * How to order: See ‘How to Order’, below. Gold Box “Infinity” Power Supplies F1; Table top rubber mounting feet, Option “F1” ........$15 Alarm with Relay Contacts Options ........$15 + *$35(one-time only) Choose one: G1 or G2 G1; NC Relay contacts close when output voltage drops more than 10% below nominal. G2; NO Relay contacts open when output voltage drops more than 10% below nominal. G3; Status LEDs on Front Cover, Option “G3” ........$15 + *$35(one-time only) Green LED indicates Vout is between -10% and +15% of rated output. Red LED indicates a fault condition; thermal (for units with option D1), overcurrent, under or overvoltage. (Available on Single Output models only.) G4; ‘Voltage output OK’ Monitor, Option “G4” ........$10 + *$35(one-time only) TTL High when Vout is between -10% and +15% of rated output. (Available on Single Output models only.) G5; Temperature monitor, Option “G5” ........$25 + *$35(one-time only) The temperature monitor is used to measure the power supply’s internal temperature. Monitor output voltage is set to 2.5 Vdc at 25°C and varies above or below this value by 0.1 Vdc per °C. For example, if the temperature is 20°C the output will be 2 Vdc. (Not available with options H1-H8). H1-H8; Additional, Low Current, Auxiliary Voltage Options ........$25 + *$35(one-time only) <1% initial Accuracy, ±0.2% Line and ±0.2% Load Regulation, <10mv peak-to-peak ripple. (Not available with option G5.) Choose one: H1 or H2 or H3 or H4 or H5 or H6 or H7 or H8 H1; Auxiliary output: 3.3 Vdc, 0.1 amp H2; Auxiliary output: 5 Vdc, 0.1 amp H3; Auxiliary output: 12 Vdc, 0.1 amp H4; Auxiliary output: 13.8 Vdc, 0.1 amp H5; Auxiliary output: 15 Vdc, 0.1 amp H6; Auxiliary output: -5 Vdc, 0.1 amp H7; Auxiliary output: -12 Vdc, 0.1 amp H8; Auxiliary output: -15 Vdc, 0.1 amp J3; Redundancy (‘OR-ing’ or ‘Blocking Diode’), Option “J3” ........$190 Redundancy is attained by simply wiring two units in parallel. Derate output by 10%. (Available on Single Output models only. Not available with options C5, C6, C9, E5.) Includes: • Non-latching OVP set 15% above rated output (Option A1). • Alarm with relay contacts that close when output voltage drops more than 10% below nominal (Option G1). • Output blocking protection diode (Option E1). • Remote sensing. K3; 6' IEC AC input Cord 115 VAC, Option “K3” ........$15 K4; 6' IEC AC input Cord 230 VAC, Option “K4” ........$15 K5; Rear Panel AC input fuse, Option “K5” (Not available with option B1 or on case size LM6A.) ........$10 K6; Final Test Data, Option “K6” ........$35 Final test data also includes an extended 8 hour burn-in. K7; AC on/off LED on Front Cover, Option “K7” ........$10 Red LED indicates AC is on. L1 thru L3; see B3 thru B6 (that section includes L1, L2 and L3, which follows B3 thru B6.) *The “$35(one-time only charge)” is only added to the total cost of the power supply one time no matter how many options are ordered. See How To Order. Online Ordering and Instant Quotes for ALL Acopian power supplies at www.acopian.com 4 P.O. Box 638, Easton, PA 18044 • Phone: (610) 258-5441 • FAX: (610) 258-2842 How to Order: There are a seemingly infinite number of options available for the new Acopian Gold Box “Infinity” power supplies! And even more options will be available soon! This worksheet should make it easy to select and price the model that you desire. • Add options as a suffix to the power supply model number. For example, if options C3 and C9 are selected, the suffix on the model number is C39, denoting options C3 and C9. • The “$35(one-time only charge)” is just that; once that $35 is added into the cost of the power supply, it doesn’t need to be added again for any other option that is selected. See example below. For example, power supply model L5MC500 with options A1, B6, C3 and C9: L5MC500 ........... $280 A1....................... $15 + *$35(one-time only) B6....................... $20 Do not include this $35 because it has C3....................... $10 + *$35(one-time only) already been added from Option A1. C9......................... $5 This model number would be L5MC500A1B6C39, and the price would be $280 +(15+35) +20 +10 +5 = $365 Online Ordering and Instant Quotes for ALL Acopian power supplies at www.acopian.com 5 P.O. Box 638, Easton, PA 18044 • Phone: (610) 258-5441 • FAX: (610) 258-2842 8/1/11 Gold Box “Infinity” SINGLE OUTPUT MODELS ------------ Any other voltage between 1.5 and 150 can easily be made. ------------ Output Current Regulation Output Current Regulation Ripple mV Ripple mV Nominal Adjust Nominal Adjust Amps. at (@ 25 MHz BW) Amps. at (@ 25 MHz BW) Output Range Output Range ($) Case ($) Case Load Line Load Line Voltage ± V Voltage ± V 40°C 71°C ±mv ±mv Price Model Size 40°C 71°C ±mv ±mv Price Model Size RMS P-P RMS P-P 1.5 0.5 5 3.5 22 0.25 0.75 280 L1.5MC500 LM6A 20 1 2.3 1.6 22 0.25 0.75 290 L20MC230 LM6A 1.5 0.5 10 72 2 0.25 0.75 340 L1.5MC1000 LM8A 20 1 4.4 3.1 22 0.25 0.75 345 L20MC440 LM8A 1.5 0.5 13.2 9.2 22 0.25 0.75 380 L1.5MC1320 LM10A 20 1 6.6 4.6 22 0.25 0.75 385 L20MC660 LM10A 3.3 0.5 5 3.5 22 0.25 0.75 280 L3.3MC500 LM6A 24 1 2.3 1.6 33 0.25 0.75 290 L24MC230 LM6A 3.3 0.5 10 72 2 0.25 0.75 340 L3.3MC1000 LM8A 24 1 3.9 2.7 33 0.25 0.75 345 L24MC390 LM8A 3.3 0.5 13.2 9.2 22 0.25 0.75 380 L3.3MC1320 LM10A 24 1 6.1 4.2 33 0.25 0.75 385 L24MC610 LM10A 5 0.5 5 3.5 22 0.25 0.75 280 L5MC500 LM6A 28 12 1.4 33 0.25 0.75 290 L28MC200 LM6A 5 0.5 10 72 2 0.25 0.75 340 L5MC1000 LM8A 28 1 3.3 2.3 33 0.25 0.75 345 L28MC330 LM8A 5 0.5 13.2 9.2 22 0.25 0.75 380 L5MC1320 LM10A 28 1 5.5 3.9 33 0.25 0.75 385 L28MC550 LM10A 6 0.5 5 3.5 22 0.25 0.75 280 L6MC500 LM6A 30 1 1.9 1.3 33 0.25 0.75 290 L30MC190 LM6A 6 0.5 10 72 2 0.25 0.75 340 L6MC1000 LM8A 30 1 3.3 2.3 33 0.25 0.75 345 L30MC330 LM8A 6 0.5 13.2 9.2 22 0.25 0.75 380 L6MC1320 LM10A 30 1 5.2 3.6 33 0.25 0.75 385 L30MC520 LM10A 7 0.5 5 3.5 22 0.25 0.75 280 L7MC500 LM6A 36 1 1.4 13 3 0.25 0.75 290 L36MC140 LM6A 7 0.5 10 72 2 0.25 0.75 340 L7MC1000 LM8A 36 1 2.5 1.8 33 0.25 0.75 345 L36MC250 LM8A 7 0.5 13.2 9.2 22 0.25 0.75 380 L7MC1320 LM10A 36 1 4.4 3.1 33 0.25 0.75 385 L36MC440 LM10A 8 0.5 5 3.5 22 0.25 0.75 280 L8MC500 LM6A 48 1 1.3 0.9 33 0.25 0.75 330 L48MC130 LM6A 8 0.5 10 72 2 0.25 0.75 340 L8MC1000 LM8A 48 12 1.4 33 0.25 0.75 370 L48MC200 LM8A 8 0.5 13.2 9.2 22 0.25 0.75 380 L8MC1320 LM10A 48 1 3.3 2.3 33 0.25 0.75 405 L48MC330 LM10A 10 0.5 4.7 3.3 22 0.25 0.75 290 L10MC470 LM6A 60 11 0.7 33 1 3 330 L60MC100 LM6A 10 0.5 8.5 62 2 0.25 0.75 345 L10MC850 LM8A 60 1 1.5 1.1 33 1 3 370 L60MC150 LM8A 10 0.5 12 8.4 22 0.25 0.75 385 L10MC1200 LM10A 60 1 2.6 1.8 33 1 3 405 L60MC260 LM10A 12 1 4.5 3.2 22 0.25 0.75 290 L12MC450 LM6A 75 1 0.7 0.5 55 1 3 330 L75MC70 LM6A 12 1 7.2 52 2 0.25 0.75 345 L12MC720 LM8A 75 1 1.1 0.8 55 1 3 370 L75MC110 LM8A 12 1 10 72 2 0.25 0.75 385 L12MC1000 LM10A 75 1 2.2 1.5 55 1 3 405 L75MC220 LM10A 13.8 14 2.8 22 0.25 0.75 290 L13.8MC400 LM6A 100 1 0.6 0.4 55 1 3 375 L100MC60 LM6A 13.8 1 6.3 4.4 22 0.25 0.75 345 L13.8MC630 LM8A 100 1 0.9 0.6 55 1 3 405 L100MC90 LM8A 13.8 1 8.7 62 2 0.25 0.75 385 L13.8MC870 LM10A 100 1 1.3 0.9 55 1 3 435 L100MC130 LM10A 15 1 3.1 2.2 22 0.25 0.75 290 L15MC310 LM6A 120 1 0.6 0.4 55 1 3 375 L120MC60 LM6A 15 1 6.1 4.2 22 0.25 0.75 345 L15MC610 LM8A 120 1 0.75 0.5 55 1 3 405 L120MC75 LM8A 15 1 9.4 6.5 22 0.25 0.75 385 L15MC940 LM10A 120 1 1.1 0.8 55 1 3 435 L120MC110 LM10A 16 1 2.9 22 2 0.25 0.75 290 L16MC290 LM6A 125 1 0.5 0.4 55 1 3 375 L125MC50 LM6A 16 1 5.7 42 2 0.25 0.75 345 L16MC570 LM8A 125 1 0.7 0.5 55 1 3 405 L125MC70 LM8A 16 1 8.8 6.2 22 0.25 0.75 385 L16MC880 LM10A 125 1 1.2 0.8 55 1 3 435 L125MC120 LM10A 18 1 2.5 1.8 22 0.25 0.75 290 L18MC250 LM6A 150 1 0.35 0.2 55 1 3 375 L150MC35 LM6A 18 15 3.5 22 0.25 0.75 345 L18MC500 LM8A 150 1 0.5 0.3 55 1 3 405 L150MC50 LM8A 18 1 7.5 5.3 22 0.25 0.75 385 L18MC750 LM10A 150 11 0.7 55 1 3 435 L150MC100 LM10A Online Ordering and Instant Quotes for ALL Acopian power supplies at www.acopian.com 6 P.O. Box 638, Easton, PA 18044 • Phone: (610) 258-5441 • FAX: (610) 258-2842 8/1/11 Gold Box “Infinity” WIDE ADJUST OUTPUT MODELS Regulation Ripple mV Output Current Output Amps. at (@ 25 MHz BW) Voltage Load Line ($) Case Range ±mv ±mv Price Model Size 40°C 71°C RMS P-P 0-5 3.3 2.3 22 0.25 0.75 $365 YL05MC330 LM6A 0-5 5.5 3.9 22 0.25 0.75 $395 YL05MC550 LM8A 0-5 8.8 6.2 22 0.25 0.75 $455 YL05MC880 LM10A 0-6 2.7 1.9 22 0.25 0.75 $365 YL06MC270 LM6A 0-6 4.5 3.2 22 0.25 0.75 $395 YL06MC450 LM8A 0-6 8.8 6.2 22 0.25 0.75 $455 YL06MC880 LM10A 0-10 3 2.1 22 0.25 0.75 $365 YL010MC300 LM6A 0-10 4 2.8 22 0.25 0.75 $395 YL010MC400 LM8A 0-10 7 4.9 22 0.25 0.75 $455 YL010MC700 LM10A 0-12 2.5 1.8 22 0.25 0.75 $365 YL012MC250 LM6A 0-12 3.5 2.5 22 0.25 0.75 $395 YL012MC350 LM8A 0-12 6.8 4.8 22 0.25 0.75 $455 YL012MC680 LM10A 0-16 2.2 1.5 22 0.25 0.75 $365 YL016MC220 LM6A 0-16 3.3 2.3 22 0.25 0.75 $395 YL016MC330 LM8A 0-16 5.5 3.9 22 0.25 0.75 $455 YL016MC550 LM10A 0-20 1.7 1.2 22 0.25 0.75 $365 YL020MC170 LM6A 0-20 2.6 1.8 22 0.25 0.75 $395 YL020MC260 LM8A 0-20 4.2 2.9 22 0.25 0.75 $455 YL020MC420 LM10A 0-24 1.5 1.1 33 0.25 0.75 $365 YL024MC150 LM6A 0-24 2.3 1.6 33 0.25 0.75 $395 YL024MC230 LM8A 0-24 3.5 2.5 33 0.25 0.75 $455 YL024MC350 LM10A 0-25 1.4 13 3 0.25 0.75 $365 YL025MC140 LM6A 0-25 2.2 1.5 33 0.25 0.75 $395 YL025MC220 LM8A 0-25 3.4 2.4 33 0.25 0.75 $455 YL025MC340 LM10A 0-30 1.1 0.8 33 0.25 0.75 $365 YL030MC110 LM6A 0-30 1.8 1.2 33 0.25 0.75 $395 YL030MC180 LM8A 0-30 2.8 1.9 33 0.25 0.75 $455 YL030MC280 LM10A 0-36 1 0.7 33 0.25 0.75 $405 YL036MC100 LM6A 0-36 1.5 1.1 33 0.25 0.75 $455 YL036MC150 LM8A 0-36 2.4 1.7 33 0.25 0.75 $510 YL036MC240 LM10A 0-50 0.7 0.5 33 0.25 0.75 $405 YL050MC70 LM6A 0-50 0.9 0.7 33 0.25 0.75 $455 YL050MC90 LM8A 0-50 1.3 0.9 33 0.25 0.75 $510 YL050MC130 LM10A 0-60 0.6 0.4 33 1 3 $405 YL060MC60 LM6A 0-60 0.8 0.6 33 1 3 $455 YL060MC80 LM8A 0-60 1.1 0.8 33 1 3 $510 YL060MC110 LM10A 0-100 0.3 0.21 55 1 3 $405 YL0100MC30 LM6A 0-100 0.5 0.35 55 1 3 $455 YL0100MC50 LM8A 0-100 0.7 0.49 55 1 3 $510 YL0100MC70 LM10A 0-150 0.15 0.11 55 1 3 $405 YL0150MC15 LM6A 0-150 0.3 0.21 55 1 3 $455 YL0150MC30 LM8A 0-150 0.4 0.28 55 1 3 $510 YL0150MC40 LM10A Online Ordering and Instant Quotes for ALL Acopian power supplies at www.acopian.com 7 P.O. Box 638, Easton, PA 18044 • Phone: (610) 258-5441 • FAX: (610) 258-2842 3/29/10 Gold Box “Infinity” Power Supplies LINEAR REGULATED (to 150 watts) AC-DC single output & wide adjust output ‘Auxiliary’ drawing for options: ‘Base’ drawing 1 C2, C3,C4, C5,C6, C7, G1,G2, G3, G4, G5, 4.92 H1,H2,H3,H4,H5,H6,H7,H8 Front Cover Fan Fan Pluggable Terminal Exhaust Exhaust Block Connections PluggableTerminal Blocks (2) Front Cover 3.44 with clamping screws on top [1] Aux/Tmp 1 + + – – Vok(grn LED) NL OutSS Out [2] Alarm (NO or NC) VAdj Fault(red LED) 1 [3] Alarm Common .81 [4] V ok .78 .78 .15 [5] S bus (Typ.) [6] Inh/Ena .2 .41 V Adj (Typ.) [7] I mon .53 I Adj 12 2.04 [8] V mon [9] 0.81 I pgrm .98 [10] Ref 0.45 [11] V pgrm 1.44 [12] 12 Rtn 1.0 2.04 0.21 SIDE MOUNTING BOTTOM MOUNTING 8-32 threaded holes(4). 8-32 threaded holes(4). Maximum incursion of L M screws into mounting Maximum incursion of holes: 5/16” (.312”) ‘Auxiliary’ drawing for options: screws into mounting holes: 5/16” (.312”) Front Cover C1, C8 V Adj 4.3 3.0 knob 21 1.0 22 I Adj knob Rear Cover 1.89 Fan Intake 2.58 3.44 Case Approx. Size L M Weight LM6A 6.7 4.0 4 lb. All dimensions in inches. LM8A 8.12 6.0 5 lb. 5 oz. LM10A 10.12 7.0 7 lb. 4 oz. Online Ordering and Instant Quotes for ALL Acopian power supplies at www.acopian.com 8 P.O. Box 638, Easton, PA 18044 • Phone: (610) 258-5441 • FAX: (610) 258-2842 Fan Exhaust