ACCURIDE 3832HDSC

MODEL 3832CHDSC Vertical Drawer Adjustment APPLICATIONS: Use when a stay-close and stronger self-closing action is required as in industrial workstations, residential and kitchen Heavy-Duty Self-Close v cabinetry, casework, and medical emergency carts. Not intended Stay-Close for lateral file drawer applications. This product is covered by U.S. Optional Face Frame Brackets (6,145,945) and various foreign patents issued and/or pending. Slide Travel Slide Length 1.38 .50 F 1.38 D [35.1] [12.7] [35.1] E TYP. C .70 8.82 .50 B [17.8] [224.0] [25.4] .45 A [11.4] .35 5.04 Disconnect 5.04 TYP. * [9.0] [128.0] Lever [128.0] 1.80 [45.7] 2.38 .172 DIA. .85 [60.5] .180 DIA. .50 [4.4] TYP. [21.6] .187 X .310 [4.6] (4X) [12.7] .250 DIA. .35 .180 X .375 .172 X .38 1.35 [4.7 X 7.9] [6.4] TYP. [9.0] [4.6 X 9.5] [4.4 X 9.5] [34.3] TYP. TYP. TYP. Slot not accessible * on 16" and 20" lengths. NOTE: Drawer width should not exceed slide length. Finish Clear electroplate (C) or black electroplate (CB) finish z NOTE: For optimal performance, make drawer 1-1/16" [27.0mm] less than cabinet opening. w Load Slides rated at 100 lbs [45 kg] per pair NOTE: Slides may not function properly if side space is less than .50" [12.7mm]. Length 12" to 26" [300mm to 650mm] Part Slide Slide Detent Force 6 to 9 lb. [2.7 to 4.1 kg.] per slide AB C D E F Number Length Travel Side Space .50" (+ .031 -0.00) 11.81 11.25 9.09 [12.7mm] (+ 0.8 -0.0) 3832-C12HDSC [300] [286] [231] Travel See chart 13.78 14.00 11.06 3832-C14HDSC Height 1.80" [45.7mm] [350] [356] [281] Disconnect Handed lever disconnect 15.75 16.00 13.03 11.34 3832-C16HDSC [400] [406] [331] [288] Mounting Side; optional brackets for face frame mounting 17.72 18.00 12.60 14.99 12.60 3832-C18HDSC [450] [457] [320] [381] [320] Features Drawer member vertical cam 19.69 20.00 16.96 15.12 adjustment. Silenced open and 3832-C20HDSC [500] [508] [432] [384] closed. Self-close and stay-close action eliminates bounce-back and 21.65 22.00 16.38 18.93 16.38 3832-C22HDSC drawer creep. [550] [559] [416] [481] [416] 23.62 24.00 8.82 16.38 20.90 13.86 18.90 A lateral file drawer is wider than it is deep. v 3832-C24HDSC [600] [610] [224] [416] [531] [352] [480] z Minimum order quantities may apply. 25.59 26.00 8.82 16.38 21.42 22.87 13.86 20.16 w Load rating based on 18" slides mounted 3832-C26HDSC [650] [660] [224] [416] [544] [581] [352] [512] in a 16" wide drawer. Installation Instructions Install Cabinet Member Conventional Mounting - Cabinet Figure 1 1. Separate slide members by simultaneously lifting up the left hand disconnect lever and pushing down the right hand lever. 2. Install cabinet (large) member first. For applications with an Horizontal Slots overlay drawer front, refer to Figure 1 for conventional mounting and Figure 2 for 32mm System mounting. For applications Drawer with an inset drawer front, set the slide back the thickness of the drawer front plus 1/8" [3.2mm]. 1-1/2" Install Drawer Member 3. Install the drawer member with a screw through the cam For overlay adjuster and through a hole or slot at the rear. drawer front 2-3/8" Cabinet Member NOTE: Cam must install C L Figure 2 32MM Mounting - Cabinet on same center line as drawer member. Rear Cam Adjustor Mounting Slot Cabinet 37.0mm 2.0mm NOTE: 1/16" Member [1.6mm] The cam is designed for use with the standard Drawer Maximum Accuride truss head screw. If using other screw, Head Height ensure screw head height does not exceed 1/16" Accuride part number 38.1mm [1.6mm] since it may cause interference. System Holes 2410-3218-CE For overlay Conventional and 32MM Mounting drawer front 11/16" Drawer [17.8] Optional Face Frame Brackets Conventional Vertical Slots Face frame brackets are ordered as a kit or in bulk. Brackets are available in clear zinc finish only. Mounting screws are not included. 1-1/4" To order kits, specify part number 32MM System Vertical Slot [31.8] Optional front 4180-0322-XE. Each kit contains clip-onbracket 1/8" for Conventional Mounting 2 front brackets, 2 rear 1/4" part number [5.2] for 32mm System Mounting brackets, and installation [6.4] 4180-0516-CE instructions. Order 1 kit 4. Make sure the ball bearing retainers in the cabinet side are per pair of slides. fully forward. Install drawer into cabinet. Close the drawer. For bulk, order 2 front brackets 5. Open drawer and rotate the cam with a Phillips or Pozi screw- (P/N 4180-0516-CE) driver to vertically position the drawer in relation to the cabinet. and 2 rear brackets Optional rear metal (P/N 4080-0508-CE) face frame bracket NOTE: per pair of slides. part number Total vertical 4080-0508-CE adjustment is 1/8" [3.2mm] Rotate Cam Up or Down Packaging –1/16" [1.6mm] from center, Distibutor (D) Pack: All lengths are packaged 10 pair per box. up and down. Polybag includes one pair of slides with mounting screws. Bulk (P) Pack: All lengths are packaged 10 pair per box. Slides 6. Install additional set screws to secure. and screws are ordered and packaged separately. NOTE: Install drawer pulls or knobs after set screws are in place. Specifications Slide members and ball retainers: Cold rolled steel Ball bearings: Carburized steel Additional Note: Specifications, materials, prices, terms, and delivery are Mounting Locations subject to change without notice. Slide Ordering Instructions Complete your slide order for Accuride models 3832CHDSC by specifying the following: ACCURIDE INTERNATIONAL INC. 50 Pair C 3832 -C18 HDSC D 12311 Shoemaker Avenue Total Required Slides Santa Fe Springs, CA 90670 Slide Finish TEL (562) 903-0200 Slide Model FAX (562) 903-0208 Slide Length www.accuride.com Heavy-Duty Self-Close Feature Manufacturing, Engineering, and Sales Polybag Packaging United States � Germany � Japan � Mexico � United Kingdom Copyright ' 2003 Accuride International Inc. Printed in U.S.A. 3700-1112(9467)-MK574-R1-0803 Copyright ' 2003 Accuride International Inc. Printed in U.S.A. 3700-9467(1112)-MK095-R1-0803