Elite.Parts

Description

XP Power PMP110-45-2 Power Supply - 110W AC/DC Medical Desktop

Part Number

PMP110-45-2

Price

Request Quote

Manufacturer

XP POWER

Lead Time

Request Quote

Category

POWER SUPPLY

Specifications

Derating

Derate from 100% at +50°C, linearly to 50% at +70°C

Earth leakage current

90uA max. @ 115VAC, 60Hz; 150uA max. @230VAC, 50Hz

Efficiency

70%minimum on single output models with Vo>12V, 65% minimum on the others

EMC Performance (EN60601-1-2: 2001)

EN55011:Class B conducted, Class B radiated; FCC:Class B conducted, Class B radiated; VCCI:Class B conducted, Class B radiated; EN61000-3-2:Harmonic distortion , Class A; EN61000-3-3:Line flicker; EN61000-4-2:ESD, ± 8KV air and ± 6KV contact; EN61000-4-3:Radiated immunity, 3V/m for 80~2500MHz; EN61000-4-4:Fast transient/burst, ± 2KV; EN61000-4-5:Surge, ± 1KV diff., ± 2KV com.; EN61000-4-6:Conducted immunity, 3Vrms; EN61000-4-8:Magnetic field immunity, 3A/m;EN61000-4-11:Voltage dips, 30?reduction for 500ms, 60% reduction for 100ms and >95? reduction for 10ms

Hold-up time

12 msec minimum at 110VAC

Input current

3.20A (rms) for 115 VAC; 1.80A (rms) for 230VAC

Input frequency

47 to 63Hz

Input voltage

85 to 264VAC

Inrush current

15 amps @ 115VAC or 30 amps @ 230VAC, at 25°C cold start

Line regulation

±0.5% maximum at full load

MTBF

550,000 hours minimum at full load at 25°C ambient , calculated per MIL-HDBK-217F, excluding DC fan.

Overcurrent protection

All outputs protected to short circuit conditions

Overvoltage protection

Provided on output #1 only; set at 112-132%of its nominal output voltage

PFD signal (optional)

TTL logic high for normal operation and TTL logic low upon loss of input power. This signal appears at least 1ms prior to +5V output dropping 5% below its nominal value. This signal also provides a minimum delay of 100ms after +5V is within regulation.

Relative humidity

5% to 95% non-condensing

Ripple and noise

1% peak to peak maximum

Safety Standard Approvals

UL 2601-1, CSA C22.2 NO. 601.1 Fil e No. E178020; TÜV EN60601-1 Certificate No. T9954597

Switching frequency

20KHz to 250KHz, varies with load and line

Temperature

Operating:0°C to +70°C; Storage:-40°C to +85°C

Temperature coefficient

All outputs ±0.04/°C maximum

Total output power

110 watts maximum

Transient response

Maximum excursion of 4% or better on all models, recovering to 1% of final value within 500us after a 25% step load change

Withstand voltage

4000VAC from input to output; 1500VAC from input to ground; 500VAC from output to ground

Datasheet

XP Power=PMP110-45-2=datasheet1-1661740275.pdf

292 KiB

Download

Extracted Text

PROTEK 110 WATT MEDICAL SWITCHING POWER SUPPLIES PMP110 SERIES DESCRIPTION (LVD) The PMP110 series of AC/DC switching power RoHS supplies are for 110 watts of continuous output power. They are enclosed in a 94V-1 rated polyphenylene-oxide case with an IEC 320 inlet to mate with interchangeable cord for world-wide use. An on/off switch can be added at request. All models meet CISPR 11 and FCC class B emission limits, and are designed for medical applications, not for life support equipment. FEATURES ‧ Dual, triple or quadruple outputs ‧ Optional output connectors ‧ Optional on/off switch Safety Standard Approvals： ‧ Optional Power Fail Detect (PFD) signal ‧ 100% burn-in UL 2601-1, CSA C22.2 NO. 601.1 ‧ Wide input range 85 to 264VAC File No. E178020 ‧ Input surge current protection ‧ Overvoltage protection TÜV EN60601-1 ‧ Overcurrent protection Certificate No. T9954597 ‧ Compliant with RoHS requirements ENVIRONMENTAL SPECIFICATIONS Operating temperature： 0℃to +70℃ Storage temperature： -40℃to +85℃ INPUT SPECIFICATIONS Relative humidity： 5﹪ to 95﹪ non-condensing Input voltage： 85 to 264VAC Derating： Derate from 100﹪ at +50℃ Input frequency： 47 to 63Hz linearly to 50﹪ at +70℃ Input current： 3.20A (rms) for 115 VAC 1.80A (rms) for 230VAC GENERAL SPECIFICATIONS Earth leakage current： 90uA max. @ 115VAC, 60Hz Switching frequency： 20KHz to 250KHz, varies with load 150uA max. @230VAC, 50Hz and line Efficiency： 70﹪minimum on single output models with Vo ≧ 12V, 65% minimum on the others Hold-up time： 12 msec minimum at 110VAC OUTPUT SPECIFICATIONS Line regulation： ±0.5﹪ maximum at full load Output voltage/current： See rating chart Inrush current： 15 amps @ 115VAC or 30 amps @ 230VAC, at 25℃ cold start Total output power： 110 watts maximum Withstand voltage： 4000VAC from input to output Ripple and noise： 1﹪peak to peak maximum 1500VAC from input to ground Provided on output #1 only; Overvoltage protection： 500VAC from output to ground set at 112-132﹪of its nominal MTBF： 550,000 hours minimum at full load output voltage at 25℃ ambient , calculated per All outputs protected to short MIL-HDBK-217F, excluding DC fan. Overcurrent protection： circuit conditions EMC Performance (EN60601-1-2: 2001) All outputs ±0.04/℃ maximum Temperature coefficient： EN55011: Class B conducted, Class B radiated FCC: Class B conducted, Class B radiated Maximum excursion of 4 ﹪ or VCCI: Class B conducted, Class B radiated Transient response： better on all models, recovering to EN61000-3-2: Harmonic distortion , Class A 1 ﹪of final value within 500us EN61000-3-3: Line flicker after a 25﹪step load change EN61000-4-2: ESD, ± 8KV air and ± 6KV contact PFD signal (optional): TTL logic high for normal EN61000-4-3: Radiated immunity, 3V/m for 80~2500MHz operation and TTL logic low EN61000-4-4: Fast transient/burst, ± 2KV upon loss of input power. This EN61000-4-5: Surge, ± 1KV diff., ± 2KV com. signal appears at least 1ms EN61000-4-6: Conducted immunity, 3Vrms prior to +5V output dropping EN61000-4-8: Magnetic field immunity, 3A/m 5% below its nominal value. EN61000-4-11: Voltage dips, 30﹪reduction for 500ms, This signal also provides a 60% reduction for 100ms and >95﹪ minimum delay of 100ms after reduction for 10ms +5V is within regulation. 4-9 PMP110 MEDICAL SERIES UNIVERSAL INPUT OUTPUT VOLTAGE/CURRENT RATING CHART Maximum Output #1 Output #2 (1) Output #3 Output #4 Output MODEL (2) Vnom. Imin. Imax. Tol. Vnom. Imin. Imax. Ipeak Tol Vnom. Imin. Imax. Tol Vnom. Imin. Imax. Tol. Power PMP110-23 +5V 0.8A 10A5% +12V 0A 5A 9.0A5% (N/A) (N/A) 110W PMP110-31 +5V 0.8A 10A5% +12V 0A 5A 9.0A5%-12V 0A 2A 5% (N/A) 110W PMP110-32 +5V 0.8A 10A5% +15V 0A 4A 7.5A5%-15V 0A 2A 5% (N/A) 110W PMP110-40 +5V 0.8A 10A5% +12V 0A 5A 9.0A5%-12V 0A 2A 5% -5V 0A 2A 5% 110W PMP110-41 +5V 0.8A 10A5% +15V 0A 4A 7.5A5%-15V 0A 2A 5%+24V 0A 2A 5% 110W PMP110-42 +5V 0.8A 10A5% +12V 0A 5A 9.0A5%-12V 0A 2A 5%+12V 0A 2A 5% 110W PMP110-45 +5V 0.8A 10A5% +12V 0A 5A 9.0A5%-12V 0A 2A 5%+24V 0A 2A 5% 110W PMP110-45-1 +5V 2.0A 10A 5% +12V 0A 5A 9.0A 5% -12V 0A 2A 5% +24V 1.5A 3A 10% 110W PMP110-45-2 +5V 0.8A 10A 5% +24V 0A 3A 5.0A 5% -12V 0A 2A 5% +12V 0A 2A 5% 110W PMP110-46 +5V 0.8A 10A5% +15V 0A 4A 7.5A5%-15V 0A 2A 5% -5V 0A 2A 5% 110W NOTES: 1. Peak output current with 10% maximum duty cycle for less than 60 seconds. Total peak power must not exceed 130 watts. 2. The output #1 of model PMP110-45-1 needs a minimum current of 2A to support the other outputs at their maximum rated loads. MECHANICAL SPECIFICATIONS NOTES: 1. Dimensions shown in inch [mm] 2. Tolerance 0.02 [0.5] maximum 3. Weight: 1.40 Kgs (3.08 Lbs.) approx. 4. See pages 6-19 to 6-26 for optional output connectors. Add the suffix assigned for a selected connector to a wanted model number, e.g.PMP110-31-K1, for ordering. 5. To order a model with on/off switch, add suffix “S” to the model number. e.g. PMP110-31-K1-S. 6. To order a model with PFD signal, add suffix “PF” to the model number, e.g. PMP110-31-K1-PF. PIN CHART 1 2 3 4 5 6 7 8 PIN MODEL COMMON OUTPUT OUTPUT COMMON OUTPUT N.C. or PMP110-23 N.C. N.C. RETURN #1. #2. RETURN #1 PFD COMMON OUTPUT OUTPUT OUTPUT COMMON OUTPUT N.C. or PMP110-31 PMP110-32 N.C RETURN #3 #1. #2. RETURN #1 PFD PMP110-40 PMP110-41 PMP110-42 PMP110-45 COMMON OUTPUT OUTPUT OUTPUT OUTPUT COMMON OUTPUT N.C. or PMP110-45-1 PMP110-45-2 RETURN #3 #1. #4 #2.. RETURN #1 PFD. PMP110-46 4-10

Frequently asked questions

At GID Industrial (Elite.Parts' parent company), we specialize in procuring industrial parts. We know where to find the rare and obsolete equipment that our customers need in order to get back to business. There are other companies who claim to do what we do, but we're confident that our commitment to quality and value is unparalleled in our field.

Warranties differ by part and by which suppliers we use to procure it for you. Sometimes, a part will be sold as-is and without a warranty. Our specialty, single board computers, tend to receive a one-year warranty.

Elite.Parts can ship via FedEx, UPS, DHL, and USPS. We have accounts with each of them and generally ship using one of those, but we can also ship using your account if you would prefer. However, we can use other carriers if it will be more convenient for you.

Absolutely! We are happy to serve customers regardless of location. We work with international clients all the time, and we are familiar with shipping to destinations all across the globe.

All major credit cards are accepted: Visa, MasterCard, Discover, and American Express. We will also accept payment made with wire transfer or PayPal. Checks will only be accepted from customers in the USA. Terms may available for larger orders, upon approval.

What they say about us

FANTASTIC RESOURCE

One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!

Bucher Emhart Glass

EXCELLENT SERVICE

With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.

Fuji

HARD TO FIND A BETTER PROVIDER

Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.

Applied Materials

CONSISTENTLY DELIVERS QUALITY SOLUTIONS

Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.

Nidec Vamco

TERRIFIC RESOURCE

This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.

Trican Well Service

GO TO SOURCE

When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.

ConAgra Foods

Why buy from GID?

What they say about us

Related Products