150 Watts xppower.com AML150 Series • High Power Density • Single Outputs from 12 V to 24 V • Universal Input • High Efficiency • 0 °C to +70 °C Operating Temperature • Non-standard Connectors Available • International Safety Approvals Specification Input General Input Voltage • 90-264 VAC Efficiency • 88% min Input Frequency • 47-63 Hz Isolation • 3000 VAC Input to Output 1500 VAC Input to Ground Input Current • 2.0 A rms at 115 VAC, Output 0 V is electrically connected to 1.0 A rms at 230 VAC Input Ground Inrush Current • 60 A at 115 VAC, 120 A at 230 VAC, Switching Frequency • 20-80 kHz variable cold start +25 °C 3 Power Density • 5.1 W/In Power Factor • 0.95 typical MTBF • >100 kHrs per MIL-HDBK-217F Earth Leakage Current • 150 μA max at 115 VAC, (+25 °C ambient at full load) 250 μA max at 230 VAC Input Protection • Internal 4 A fuse Environmental Standby Power • <1 W Operating Temperature • 0 °C to +70 °C, derate from 100% power Consumption at +40 °C to 60% power at +70 °C Output Operating Humidity • 10-95% RH, non-condensing Storage Temperature • -20 °C to +80 °C Output Voltage • See table Operating Altitude • 3000 m Output Voltage Trim • Not user-adjustable Shock • 30 g, 10 ms on 3 axes Initial Set Accuracy • ±2% 2 Vibration • 5-100 Hz, 2.31 m/s , 20 mins, 3 axes Minimum Load • No minimum load required Start Up Delay • 5 s max at 100 VAC EMC & Safety Hold Up Time • 3 ms minimum at 100 VAC Emissions • EN55022/FCC/VCCI, Class B conducted Line Regulation • ±0.5% maximum EN55022/FCC/VCCI, Class B radiated Load Regulation • See table Harmonic Currents • EN61000-3-2 Transient Response • 4% max. deviation, recovery to within Voltage Flicker • EN61000-3-3 1% in 500 μs for a 25% load change ESD Immunity • EN61000-4-2, level 2 Perf Criteria A Ripple & Noise • 2% max pk-pk (see note 1) Radiated Immunity • EN61000-4-3, level 2 Perf Criteria A Overvoltage Protection • 110-140% Vnom, recycle input to reset EFT/Burst • EN61000-4-4, level 2 Perf Criteria A Overtemperature • Unit shuts down, recycle input to reset Surge • EN61000-4-5, level 3 Perf Criteria A Protection Overload Protection • 110-150%, auto recovery Conducted Immunity • EN61000-4-6, level 2 Perf Criteria A Short Circuit Protection • Trip and restart (Hiccup mode) Dips & Interruptions • EN61000-4-11, 30% for 10 ms, 60% 100 ms, 100% 5000 ms, Temperature • 0.04%/°C Perf Criteria A, B, B Coefficient Safety Approvals • EN60950, UL60950, CSA22.2 No. 60950 per cUL, CE Mark AC-DC AC-DC AML150 Models and Ratings Output Output Output Model (2) Total Regulation Power Voltage Current Number 150 W 12 V 12.50 A 5% AML150PS12†^ 150 W 15 V 10.00 A 5% AML150PS15†^ 150 W 19 V 7.89 A 5% AML150PS19†^ 150 W 20 V 7.50 A 5% AML150PS20†^ 150 W 24 V 6.25 A 5% AML150PS24†^ Notes 1. Ripple and noise measured at 20 MHz bandwidth with a 47 μF tantalum and 0.1 μF ceramic cap connected at the measurement point. 2. Total regulation includes initial set accuracy, line and load regulation. † Available from Farnell. See pages 204-206. ^ Available from Newark. See page 207-208. Mechanical Details (4) Cable length approx 70.9” ±1.97” (1800mm ±50mm) 1 3 2 4 1.6 Power On Indicator (40.7) Pin Function Rubber foot 1 Output + (4 places.) 2 Output + 3 Return/Input Earth 4 Return/Input Earth Shell Return/Input Earth 3.35 (85.0) AC Input IEC 320/C14 Inlet Notes 1. Dimensions shown in inches (mm). Tolerance is 0.02 (0.5) maximum, except output cable length. 2. Weight: 1.76 lb (800 g). 3. Optional output connectors available. Consult sales. 4. AML150PS12 cable length is 37.4” (950 mm). 5. Output connector is non locking 4 pin DC power plug and mates with Kycon part KPJ-4S or equivalent. 30-June-09 0.02 (0.5) 6.69 (170)