WHITE-RODGERS DC PRODUCTS Type 586 sealed solenoid FEATURES • Water resistant Double-make or double-break contacts Capable of handling high and low current requirements Black impact phenolic casing ENGINEERING DATA Contacts GENERAL DATA Pole form–SPNO and SPDT Dielectric Strength Material–silver alloy 500 Volts 5 Termination– / ”-24 UNF-2A thread 16 Temperature Range -40°F/-40°C to 149°F/65°C RATINGS Mechanical Life (no load) NO NC Volts DC Cont. Inrush Cont. Inrush100,000 cycles 6 200A 600 A 100A 300 A Electrical Life (rated load—making and breaking 12 200 A 600 A 100 A 300 A 200 amp on NO Contacts) 24 & 36 200 A 600 A 100 A 200 A 50,000 cycles Mounting Position Coils Recommended mounting is vertical plane Voltage–6 VDC through 48 VDC with coil terminals up Termination–#10-32 UNF-2A thread Weight (approximate) Power (approximate) SPNO–24.0 oz. Continuous 12 watts SPDT, 8 watts SPNO SPDT–26.0 oz. Connections Duty Cycle Coil isolated (two terminals) Continuous Operate (77°F/25°C) Intermittent—10 seconds “on” maximum 67% of nominal coil voltage (intermittent) and minimum 60 seconds “off” 110% max. safe of nominal coil voltage One minute “on” maximum and minimum 6 minutes “off” COIL DATA Hardware Torque Specification Resistance in Ohms Contact Terminal: 60 inch-lbs. max. § Intermittent Continuous Coil Terminal: 12-18 inch-lbs. max. Volts DC SPDT SPNO SPDT SPNO 6 2.2 3.3 3.3 5.25 12 8.4 13.2 13.2 21.0 15 13.1 21.0 21.0 32.8 24 18.4 30.0 30.0 47.0 28 33.6 53.0 53.0 84.0 36 75.6 120.0 120.0 189.0 48 134.0 213.0 213.0 336.0 § Intermittent—special request only St. Louis, Missouri Markham, Ontario 314-553-3600 905-201-4701 The Emerson logo is a R-4005B trademark and a service mark www.white-rodgers.com of Emerson Electric Co. 0746 onlinecomponents.com TYPE 586 PART NUMBERING SYSTEM 586 – x xx x x x - x Basic Part Number Series Mounting Bracket Coil Coil Termination 1 – Standard bracket Voltage/Duty 1 – Isolated Contact 02 – 6 Volt continuous Form 05 – 12 Volt continuous Factory Assigned Specials 08 – 15 Volt continuous 1 – SPNO Contact (where undefined, contact factory) 14 – 24 Volt continuous 3 – SPDT Material 16 – 28 Volt continuous No dash – Standard assem- 17 – 36 Volt continuous bly, hardware sent bulk 1 – AgCdO 20 – 48 Volt continuous 2 – Customer requested markings 3 – Customer requested markings 3A – Customer requested markings APPLICATION NOTES 5 – Customer requested Not all part number combinations are available. Please contact your Sales Representative markings for available part numbers. 6 – Customer requested Solenoids applied in battery charging circuits should be protected from higher than rated markings voltage during charging. The service life may be affected by this condition and the solenoid 6A – Customer requested may or may not operate the circuit as intended. markings 7 – Customer requested Circuits should be designed to provide safe operation should the solenoid fail in either the markings open or closed position. SPDT – Isolated Coil .281 WIDE X .640 LONG SLOT .594 NORMALLY OPEN #10-32 UNF-2A X .375 LONG W 3.300 NORMALLY 1.156 2.300 H 2.797 CLOSED 1.274 5/16-24 UNF-2A X .594 LONG CIRCUIT DIAGRAM L 1.375 4.618 SPNO – Isolated Coil .281 WIDE X .640 LONG SLOT NORMALLY .594 OPEN #10-32 UNF-2A X .375 LONG W 3.300 H 2.797 2.300 1.156 1.274 CIRCUIT DIAGRAM 5/16-24 UNF-2A X .594 LONG 1.375 L 3.688 R-4005B 0746 onlinecomponents.com