Elite.Parts Manufacturers W WESTELL A90-915000
About product Datasheet FAQ

WESTELL A90-915000

Description

CHAN SVC UN

Part Number

A90-915000

Price

Request Quote

Manufacturer

WESTELL

Lead Time

Request Quote

Category

PRODUCTS - A

Datasheet

pdf file

9150CSU.pdf

171 KiB

Extracted Text

Section 9150-00-100 Issue A Westell, Inc. December 1999 General Description & Installation Practice 030-100045 Rev. D All Rights Reserved Channel Service Unit Model 9150-00 CLEI Code: NCCSW111AA Contents 1. General page 1 2. Operating Description page 1 3. Inspection and Warranty page 2 4. Mounting page 2 5. Installer Connections page 2 6. Testing and Alignment page 2 7. Specifications page 2 1. General switches IN) in 1dB increments Switch settings are shown 1.01 The Westell 9150-00, Channel Service Unit, is in Table 1. The insertion loss of the 9150-00 at 1kHz, with used to terminate a 2-wire special service, private line cir- the attenuators set for 0dB is 1.2dB at 600 Ohms. cuit or polled network service at the customer premises. Features include over-voltage protection, current surge 2.06 A capacitor on the line side (switch controlled) is protection, a balanced termination, DC isolation and a provided to block DC current in the tip and ring circuit only switchable attenuator from 1.2 to 16.2dB, in 1dB steps. A when utilizing the 9150-00 is polled network services. The switchable polled network service capacitor is provided. switch must be closed (shorting the capacitor) for 2-wire The Westell 9150-00 is electrically equivalent to the Private Line services. WECO 150A CSU. 1.02 This practice is revised to Rev. C to reflect the Table 1. 9150-00 Attenuation Switch Settings new logo and new address for Westell. ATTENUATOR SETTINGS Desired Attenuator 1.0dB 2.0dB 4.0dB 8.0dB Loss of Setting in dB Switch Switch Switch Switch 2. Operating Description CSU (dB) (See Note) Position Position Position Position 2.01 Refer to Figure 1, the 9150-00 Block Diagram, as 0.0 to 1.7 OUT OUT OUT OUT 0 needed, while reading the following functional description 1.8 to 2.7 IN OUT OUT OUT 1 of circuit operation. 2.8 to 3.7 OUT IN OUT OUT 2 2.02 The 9150-00 is used to couple VF signals. It is a 3.8 to 4.7 IN IN OUT OUT 3 passive unit that provides an interface between voice- 4.8 to 5.7 OUT OUT IN OUT 4 band data equipment and a 2-wire Private Line (PL) ser- vice or a polled network service such as the Dataphone 5.8 to 6.7 IN OUT IN OUT 5 Select-a-Station and the Transaction Network. 6.8 to 7.7 OUT IN IN OUT 6 2.03 Signals to/from the line are coupled through the 7.8 to 8.7 IN IN IN OUT 7 transformer. The transformer terminates the line in 600 8.8 to 9.7 OUT OUT OUT IN 8 Ohms and provides longitudinal balance isolation and 9.8 to 10.7 IN OUT OUT IN 9 isolation between the telephone line and the customer equipment. 10.8 to 11.7 OUT IN OUT IN 10 2.04 Two Zener diodes protect the circuitry from tran- 11.8 to 12.7 IN IN OUT IN 11 sients and limit all signals to less than 9 Volts peak. Two 12.8 to 13.7 OUT OUT IN IN 12 resistors limit current surges on the line side and one va- 13.8 to 14.7 IN OUT IN IN 13 ristor acts as a fuse for protection against high currents on 14.8 to 15.7 OUT IN IN IN 14 the drop side. 15.8 to 16.7 IN IN IN IN 15 2.05 Two double DIP switch attenuators (S2 and S3), having values of 1dB, 2dB, 4dB and 8dB, provide overall Note: The 1kHz loss through CSU between 600-ohm source and 600-ohm load is equal to attenuator setting plus 1.2dB. attenuation of 1.2dB (all switches OUT) to 16dB (all CLEI is a trademark of Bell Communicatins Research, Inc. page 1 of 2 Printed in USA Section 9150-00-100 removal of the top cover. Remove the exposed PC board 3. Inspection and Warranty by pressing outward on one of the two metal tabs of the Inspection base plate. Route the wiring from the telephone line and 3.01 Upon receipt of the equipment, inspect it thor- customer equipment through the elongated slot in the oughly. If the equipment has been damaged in transit, re- base plate. Mount the base plate to the wall with two port the damage to the transportation company and to screws (not provided) through the two key-hole slots in Westell. the base plate. Warranty 3.02 Westell warrants this product to be free of defects 5. Installer Connections at the time of shipment. Westell also warrants this product 5.01 Installer connections are made to the appropriate to be functional for the period specified by the terms and screw terminal of the printed circuit board in accordance conditions governing the sale of the product. with Table 2. Ensure all connections are secure and the 3.03 This equipment should not be field repaired. Any Polled/Norm switch is in the correct position. attempt to repair or modify the equipment by anyone oth- er than an authorized Westell representative will void the Table 2. 9150-00 Wiring Connections warranty. If the equipment is suspected of being faulty, re- Lead Designation Screw Terminal place it with another unit and retest. If the replacement unit operates correctly, the original unit may be faulty and Customer Tip (Drop Side) CT Customer Ring (Drop Side) CR should be returned for repair. Line Tip T Repair and Return Line Ring R 3.04 Before returning equipment, a Return Material Authorization (RMA) number must first be requested from Westell. Once the number is obtained, please include a description of the problem then return the equipment to: 6. Testing and Alignment Westell, Inc. 6.01 Alignment consists of setting the attenuators for 750 N. Commons Drive the attenuation desired. For example, when all switches Aurora, IL 60504-7940 are OUT, the 9150-00 has about 1.2dB of loss; when all ATTN: R.G.M. Department switches are IN, the 9150-00 has a nominal 16.2dB of loss 3.05 Westell will repair or replace any defective West- (refer to Table 1). For 2W Private Line service, make sure ell equipment without cost during the warranty period if it switch S1 is set to Norm. Note: This same procedure is is found to be defective for any reason other than abuse, used when the unit is connected to a Polled Network ser- improper use or improper installation. If the equipment is vice except S1 must be set to the Polled position. found to be defective, contact Westell. If a replacement is 6.02 Upon completion of installation, re-position the required, it will be shipped in the fastest manner consis- top cover to the base plate and secure in place. tent with the urgency of the situation. 3.06 Westell will continue to repair or replace faulty 7. Specifications equipment beyond the warranty period for a nominal charge. Contact Westell or your local Westell Sales Rep- � Pad Range: 1.2 to 16.2dB, in 1dB steps resentative for details. � Impedance: 600 Ohms, drop and line Technical Assistance � Insertion Loss: 1kHz, 1.2dB plus attenuator 3.07 If technical assistance is required, contact the � Over-Voltage Protection: 8.2 Volts, peak Westell Technical Service Department by calling (630) � Surge Current: Varistor protected 898-2500 or 1-800-323-6883. � Polled Network Service: DC current blocking capaci- 4. Mounting tor, line side (switch selectable) � Operating Environment: 0� to 50�C 4.01 The 9150-00 is designed to mount on a wall or 3 � Dimensions: Approx. 4” x 3” x 1 / ” other flat surface directly over an outlet box. Remove the 4 cover from base plate by removing the screw followed by � Weight: Approx. 10 oz. T CT 8dB 4dB 2dB 1dB PAD PAD PAD PAD R CR NORM OUT OUT OUT OUT S1 S2 POLLED S2 S3 S3 IN IN IN IN 8dB 4dB 2dB 1dB Figure 1. 9150-00 Block Diagram page 2

Frequently asked questions

What makes Elite.Parts unique?

chervon down
At GID Industrial (Elite.Parts' parent company), we specialize in procuring industrial parts. We know where to find the rare and obsolete equipment that our customers need in order to get back to business. There are other companies who claim to do what we do, but we're confident that our commitment to quality and value is unparalleled in our field.

What kind of warranty will the A90-915000 have?

chervon down
Warranties differ by part and by which suppliers we use to procure it for you. Sometimes, a part will be sold as-is and without a warranty. Our specialty, single board computers, tend to receive a one-year warranty.

Which carriers does Elite.Parts work with?

chervon down
Elite.Parts can ship via FedEx, UPS, DHL, and USPS. We have accounts with each of them and generally ship using one of those, but we can also ship using your account if you would prefer. However, we can use other carriers if it will be more convenient for you.

Will Elite.Parts sell to me even though I live outside the USA?

chervon down
Absolutely! We are happy to serve customers regardless of location. We work with international clients all the time, and we are familiar with shipping to destinations all across the globe.

I have a preferred payment method. Will Elite.Parts accept it?

chervon down
All major credit cards are accepted: Visa, MasterCard, Discover, and American Express. We will also accept payment made with wire transfer or PayPal. Checks will only be accepted from customers in the USA. Terms may available for larger orders, upon approval.

Why buy from GID?

quality

Quality

We are industry veterans who take pride in our work

protection

Protection

Avoid the dangers of risky trading in the gray market

access

Access

Our network of suppliers is ready and at your disposal

savings

Savings

Maintain legacy systems to prevent costly downtime

speed

Speed

Time is of the essence, and we are respectful of yours

What they say about us

FANTASTIC RESOURCE

star star star star star

One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!

Bucher Emhart Glass

EXCELLENT SERVICE

star star star star star

With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.

Fuji

HARD TO FIND A BETTER PROVIDER

star star star star star

Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.

Applied Materials

CONSISTENTLY DELIVERS QUALITY SOLUTIONS

star star star star star

Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.

Nidec Vamco

TERRIFIC RESOURCE

star star star star star

This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.

Trican Well Service

GO TO SOURCE

star star star star star

When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.

ConAgra Foods

Related Products

A25A90-311511

30A T1 TST SET

30B T1 LPBACK TRMTR

MANF DISCONT

PRFRMC MON TST ACCESS

product

WESTELL-A90-312552-DS1 Network Interface Unit